JVC LT-22DE72 Instructions Manual

FRANÇAIS ENGLISH

LT-22DE72

(22” class/21.53 diagonal)

(22” classe/21,53 diagonale)

LCD TV/DVD Combo

ATTENTION

If you purchase a universal remote control from your local retailer, please contact the remote manufacturer for the

required programming code.

Si vous utilisez avec cet appareil une télécommande universelle (autre que celle vendue avec ce téléviseur),

consultez la documentation accompagnant la télécommande universelle afin de connaître le code numérique cor-

respondant au téléviseur.

AIR/CABLE MODE SELECTION

SÉLECTION DU MODE AIR/CABLE

When shipped from the factory, the Signal Type option is set to the “Cable” (Cable Television) mode.

If not using Cable TV, set this menu option to the “Air” position.

Lorsque l’appareil sort de l’usine, l’option « Signal Type » est en mode « Cable » (câblodistribution). Si vous

n’utilisez pas la câblodistribution, sélectionnez l’option « Air ».

Before operating the unit, please read this manual thoroughly.

Avant de faire fonctionner l’appareil, veuillez lire le présent guide attentivement.

IF CONTACT WITH CUSTOMER SERVICE IS REQUIRED

PLEASE HAVE THE MODEL NUMBER READY PRIOR TO THE CALL

S’IL FAUT CONTACTER LE SERVICE CLIENTÈLE, PRENEZ SOIN D’ÊTRE MUNI

DU NUMÉRO DE MODÈLE AVANT D’APPELER.

CUSTOMER SERVICE – 1-800-289-0984

SERVICE/SERVICE CLIENTÈLE: 1-800-289-0984

ORION WEBSITE

SITE WEB ORION

FOR RECYCLING INFORMATION, PLEASE VISIT ORION’S WEBSITE AT

POUR OBTENIR DES INFORMATIONS SUR RECYCLAGE, VEUILLEZ VISITER ORION’S SITE WEB:

www.orionsalesinc.com

INSTRUCTIONS

MANUAL D’ INSTRUCTIONS

57A0221A_eng.indd 157A0221A_eng.indd 1 3/14/11 10:42:10 AM3/14/11 10:42:10 AM

2

CAUTION:

THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE

READ THIS OWNER'S MANUAL CAREFULLY AND RETAIN

FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE

MAINTENANCE, CONTACT AN AUTHORIZED SERVICE

LOCATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE

PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO THE LASER BEAM,

DO NOT TRY TO OPEN THE ENCLOSURE. RADIATION MAY

BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO

NOT STARE INTO THE BEAM.

Location of the required Marking

The rating sheet and the safety caution are

on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA

RADIATION PERFORMANCE STANDARDS, 21

CFR SUBCHAPTER J.

Complies with FDA performance standards

for laser products except for deviations

pursuant to Laser Notice No. 50, dated

June 24, 2007.

The lightning flash with arrowhead

symbol, within an equilateral triangle

is intended to alert the user to the

presence of uninsulated dangerous

voltage within the product's enclosure

that may be of sufficient magnitude to

constitute a risk of electric shock.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OPEN FLAMES AWAY

FROM THIS PRODUCT AT TIMES.

CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN

BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with the FCC Rules

could void the user’s authority to operate this equipment.

ENGLISH

CLASS 1

LASER PRODUCT

Important Note:

In the spaces below, enter the model and serial number of your television (located at the rear of the television

cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user’s guide in a

convenient place for future reference. Keep the carton and original packaging for future use.

Serial number _______________________________ Model number ______________________________

57A0221A_eng.indd 257A0221A_eng.indd 2 3/14/11 10:42:14 AM3/14/11 10:42:14 AM

3

ENGLISH

15) Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such

as vases, should not be placed on the apparatus.

16) An outside antenna system should not be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can fall into such power lines or circuits. When

installing an outside antenna system, extreme care should be taken to keep from touching such

power lines or circuits, as contact with them might be fatal.

17) Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric

shock.

18) Do not push objects through any openings in this unit, as they may touch dangerous voltage

points or short out parts that could result in fire or electric shock. Never spill or spray any type of

liquid into the unit.

19) If an outside antenna or cable system is

connected to the unit, be sure the antenna or

cable system is grounded to provide some

protection against voltage surges and built-up

static charges, Section 810 of the National

Electrical Code, ANSI/NFPA 70, provides

information with respect to proper grounding of

the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location

of antenna discharge unit, connection to

grounding electrodes, and requirements for the grounding electrode.

20) When replacement parts are required, be sure the service technician uses replacement parts

specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

21) Upon completion of any service or repairs to this unit, ask the service technician to perform

safety checks to determine that the unit is in proper operating condition.

22) Keep your fingers clear of the disc slot as it is closing. It may cause injury.

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ANTENNA

LEAD IN WIRE

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUND

CLAMP

ELECTRIC SERVICE

EQUIPMENT

NEC

-

NATIONAL

ELECTRICAL CODE

S2898A

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

57A0221A_eng.indd 357A0221A_eng.indd 3 3/14/11 10:42:15 AM3/14/11 10:42:15 AM

4

IMPORTANT SAFETY INSTRUCTIONS (continued)

23) When you connect the product to other equipment, turn off the power and unplug all of the equipment from

the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's

manual of the other equipment carefully and follow the instructions when making any connections.

24) Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume

sound may cause hearing or speaker damage.

25) Do not allow the product to output distorted sound for an extended period of time. It may cause speaker

overheating and fire.

26) When you use the headphones, keep the volume at a moderate level. If you use the headphones

continuously with high volume sound, it may cause hearing damage.

27) Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the

laser beam. It may cause eye damage.

28) Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious

personal injury and product malfunction.

29) This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the NEC

that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of cable entry as practical.

30) The socket-outlet must be installed near the unit and easily accessible.

CONDENSATION

Moisture will form in the operating section of the player if the player is brought from cool surroundings into a warm

room or if the temperature of the room rises suddenly. When this happens, player's performance will be impaired.

To prevent this, let the player stand in its new surroundings for about an hour before switching it on, or make sure

that the room temperature rises gradually.

Condensation may also form during the summer if the player is exposed to the breeze from an air conditioner. In

such cases, change the location of the player.

HOW TO HANDLE THE LCD PANEL

Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur.

If the LCD panel is broken, make absolutely sure that you do not touch the liquid in the panel. This may cause

skin inflammation.

If the liquid gets in your mouth, immediately gargle and consult with your doctor. Also, if the liquid gets in your

eyes or touches your skin, consult with your doctor after rinsing for at least 15 minutes or longer in clean water.

•

CHILD SAFETY:

It Makes A Difference How and Where You Use Your Flat Panel Display

Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:

THE ISSUE

The home theater entertainment experience is a growing trend and larger flat panel displays are popular

purchases. However, flat panel displays are not always supported on the proper stands or installed

according to the manufacturer’s recommendations.

Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks, speakers,

chests or carts may fall over and cause injury.

THIS MANUFACTURER CARES!

The consumer electronics industry is committed to making home entertainment enjoyable and safe.

TUNE INTO SAFETY

One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation and use of

your flat panel display.

Carefully read and understand all enclosed instructions for proper use of this product.

Don’t allow children to climb on or play with furniture and television sets.

Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest of drawers.

Remember that children can become excited while watching a program, especially on a “larger than life” flat

panel display. Care should be taken to place or install the display where it cannot be pushed, pulled over, or

knocked down.

Care should be taken to route all cords and cables connected to the flat panel display so that they cannot be

pulled or grabbed by curious children.

WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:

Use a mount that has been recommended by the display manufacturer and/or listed by an independent

laboratory (such as UL, CSA, ETL).

Follow all instructions supplied by the display and wall mount manufacturers.

If you have any doubts about your ability to safely install your flat panel display, contact your retailer about

professional installation.

Make sure that the wall where you are mounting the display is appropriate to support the weight of the unit/

product and wall mount. If you are unsure, contact a professional installer.

A minimum of two people are required for installation. Flat panel displays can be heavy.

57A0221A_eng.indd 457A0221A_eng.indd 4 3/14/11 10:42:15 AM3/14/11 10:42:15 AM

5

ENGLISH

The unit emits heat when in operation. Do not place any covers or blankets on the unit, this may cause

overheating. Do not block ventilation holes, or set up near radiators. Do not place in direct sunshine. When

placing on a shelf leave 10 cm (4 inches) free space around the entire unit.

10cm

Notes when mounting the LCD TV/DVD on a wall

If the unit is to be mounted on the wall, contact the retailer where you purchased the LCD TV/DVD for advice,

and have the equipment professionally installed. Incomplete or improper installation may cause injury to you,

and/or damage to the LCD TV/DVD.

To hang the television on a wall, remove these screws

and then remove a stand. Before performing work spread

cushioning over the base area to lay the TV on.

IMPORTANT NOTICE

Possible Adverse Effects on LCD Panel: If a fixed (non-moving) pattern remains on the LCD Panel for

long periods of time, the image can become permanently engrained in the LCD Panel and cause subtle but

permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your

LCD Panel on for long periods of time while it is displaying the following formats or images:

Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.

Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on

a normal (4:3) display (black bars at top and bottom of screen); or viewing normal style (4:3) media on a

widescreen (16:9) display (black bars on left and right sides of screen).

The following symptoms are not signs of malfunction but technical limitation. Therefore we disclaim

any responsibility for these symptoms.

LCD Panels are manufactured using an extremely high level of precision technology, however sometimes

parts of the screen may be missing picture elements or have luminous spots.

This is not a sign of a malfunction.

Do not install the LCD Panel near electronic equipment that produces electromagnetic waves. Some

equipment placed too near this unit may cause interference.

Effect on infrared devices – There may be interference while using infrared devices such as infrared cordless

headphones.

•

SAFETY PRECAUTIONS

57A0221A_eng.indd 557A0221A_eng.indd 5 3/14/11 10:42:16 AM3/14/11 10:42:16 AM

6

How to attach the stand

NOTE:

• Unplug the AC cord from the AC INPUT terminal.

• Before beginning this process, assure that the TV is laid on a clean, safe, and cushioned surface to avoid

any damage to the unit.

• Do not touch or press the TV-screen, glass might break under pressure.

Place the TV on its front onto a table.

Align the stand’s bottom-plate (supplied) as seen here.

It will ﬁ t in only one direction.

Hold the unit and attach the stand slowly, as shown in Figure 1.

Finally secure the bottom-plate with 2 screws (supplied) as indicated by the arrows in Figure 2.

Be sure to follow the instructions. Insufficient tightening or incorrect installation of the stand will not support

your unit correctly, and could result in damage or injury from tip-over.

•

How to remove the stand

When you transport this product, remove the stand and pack ﬂ at against the back of the unit in the carton. To

remove the stand, perform these steps in reverse order.

For wall mounting, the base must be removed. To disconnect the base/stand remove the three (3) screws from

the back (see page 5).

LCD PANEL SIDE

Figure 1

Figure 2

57A0221A_eng.indd 657A0221A_eng.indd 6 3/14/11 10:42:19 AM3/14/11 10:42:19 AM

7

ENGLISH

Features

LCD color TV With DVD/CD player

Unique space saving design combines a 22” LCD color TV and a DVD/CD player.

A DVD disc has much more capacity, but is the same size as an audio CD disc. The Picture/Audio quality of a

DVD exceeds other software. The picture quality is higher than Super VHS video cassettes. The audio quality

is higher than an audio CD. The DVD also has special options; audio language selection, subtitle language

selection, or multi-angle, etc.

The DVD PLAYER can play back both audio CDs and MP3/WMA/JPEG CDs.

Compatible with a wide range of DVD audio outputs

Digital Audio Jack (Coaxial)

When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the

effect of being in a movie theater or a concert hall.

Surround standard is different from Dolby Digital. This format is already in use in many theaters. By connecting

this unit to a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs

recorded in this format can be enjoyed. However, audio will not be output from the analog audio output jacks.

By connecting this unit to an AV amplifier with a built-in MPEG decoder, the MPEG audio of DVD discs

recorded in this format can be enjoyed.

The Linear PCM sound of a 48 kHz/24 bit through 96 kHz/24 bit exceeds audio CD sound.

Convenience Features

Direct selection of your desired scenes using Title/Chapter/Time/Track - You can play back from the

desired scene.

Recalling Up to 12 Scenes -

You can program up to 12 scenes in memory and recall the marked scenes.

Frame Advance - The PAUSE and SEARCH moves one frame at a time.

Slow Motion - The SLOW moves you back and forth through the program by 4 steps of 1/16-1/2 times.

Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.

Program Playback (Audio CD/MP3/WMA CD) - You can play back tracks in programmed sequences.

Zoom - You can zoom in the selected subject on the screen during playback.

Note: Make sure that discs are suitable for the following functions.

Multi-Language - Maximum 32 language subtitles and maximum 8 language soundtracks can be played back

for movies or programs.

Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc,

you can change the angles during playback.

Parental Control - You can limit the play back of scenes or sounds of DVD discs that have a rating level

encoded on the disc.

Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor.

TV Features

LED Backlight System - It realize thin profile, low power consumption, eco-friendly Hg-less design and high

contrast picture.

Integrated Digital Tuner - You can view digital broadcasts without using a Digital TV Set-Top Box.

Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for

hearing impaired viewers.

Picture Adjustments Using The Remote Control - The On-Screen display allows precise remote control

adjustment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.

Programmable TV Sleep Timer - Operable from the remote control, the TV can be programmed for up to 120

minutes to turn off automatically.

On-Screen 3 Language Display - You can select one of 3 languages, English, French or Spanish for on-

screen programming.

V-Chip - The V-Chip function can read the rating of a TV program or movie content if the program is encoded

with this information. V-chip will allow you to set a restriction level.

•

57A0221A_eng.indd 757A0221A_eng.indd 7 3/14/11 10:42:22 AM3/14/11 10:42:22 AM

8

Contents

Before using your unit

IMPORTANT SAFETY INSTRUCTIONS ...........3

SAFETY PRECAUTIONS .................................5

IMPORTANT NOTICE .......................................5

How to attach the stand ....................................6

How to remove the stand ..................................6

Features ............................................................7

Contents ...........................................................8

Logos & Licenses .............................................8

Disc...................................................................9

Parts and functions .........................................11

Remote control ...............................................12

Power source ..................................................13

Antenna connections ......................................14

Cable TV connections .....................................14

TV operation

Starting setup .................................................15

TV operation ...................................................15

Quick guide for menu operation ......................16

Convenience functions ...................................17

Memorizing channels ......................................18

Checking the digital signal strength ................19

Labeling channels ...........................................19

Labeling video inputs ......................................19

Setting the V-Chip ...........................................20

Closed Caption ...............................................21

CC advanced ..................................................21

Setting the picture size ....................................22

DVD operation

Preparation .....................................................23

Status display of disc ......................................23

Playback procedure ........................................23

Special playback .............................................24

Zooming ..........................................................24

Locating desired scene ...................................24

A-B Repeat playback ......................................24

Marking desired scenes ..................................25

Changing angles .............................................25

Changing soundtrack language ......................25

Subtitles .......................................................... 25

Using HOME MENU .......................................26

Play mode .......................................................26

Audio Settings menu .......................................27

Video Adjust menu ..........................................28

Quick guide for DVD menu operation ..............28

Function Setup ................................................29

Parental Control ..............................................30

Additional information

Language Code List ........................................31

Country/Area Code List ..................................31

Connections to other equipment .....................32

Reception disturbances ..................................35

Problems and troubleshooting ........................36

Specifications ................................................38

limited WARRANTY .......................................39

Logos & Licenses

This item incorporates copy protection technology that is protected by U.S. patents and other intellectual

property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

is a trademark of DVD Format/Logo Licensing Corporation.

Manufactured under license from Dolby Laboratories. Dolby and the

double-D symbol are trademarks of Dolby Laboratories.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

57A0221A_eng.indd 857A0221A_eng.indd 8 3/14/11 10:42:22 AM3/14/11 10:42:22 AM

9

ENGLISH

Playable discs

Disc type and logo mark content

DVD Video

Audio

+

Video

(moving

pictures)

CD-DA

Audio

The following discs are also available.

DVD-R/RW discs of DVD video format.

CD-R/RW discs of MP3/WMA/JPEG.

•

Disc

CAUTION:

Only the left types of discs can be played on this

unit. DVD-ROM (for PC), CD-ROM (for PC), SVCD,

CVD, VCD, etc. cannot be played.

This unit cannot play an 8 cm disc. It cannot also be

played even using a disc adapter.

If you insert an irregular shaped disc, it may get

stuck and cause a malfunction.

The use of a ring protector or other disc

accessories will cause errors.

This unit is to be used exclusively with the NTSC

color system. PAL and SECAM system discs cannot

be used with this unit.

Some discs cannot be played back depending on

the recording conditions.

•

Region Number

Region number (Regional restriction code) is built-in to the unit and DVD video discs.

Region number “1” or “ALL” of DVD video discs can be used on this unit.

Title

When two or more movies are recorded on a disc, the disc

is divided into two or more sections. Each section is called

a “TITLE”.

Chapter

The titles can be subdivided into many sections.

Each section is called a “CHAPTER”.

Track

An Audio CD can contain several items.

These are assigned to the tracks.

Removing Disc from Case

Be sure to hold the edge of disc. Do not touch the surface of the disc.

Pick up the disc gently from the case.

Do not scratch the disc.

Do not get dirt on the surface of the disc.

Do not stick a label or adhesive tape on the disc.

Do not drop or bend the disc.

Storing Disc

Store the disc in the case to avoid risk of scratches, dirt or damage.

Do not leave disc exposed to direct sunlight or in hot or humid places.

Cleaning Disc

Wipe the disc with a clean, dry cloth from center to edge.

Do not wipe the disc in a circular motion.

Do not use liquid or aerosol cleaners.

•

1

ALL

CHAPTER 1

TITLE 1 TITLE 2

DVD DISC

CHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1

TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5

Audio - CD

57A0221A_eng.indd 957A0221A_eng.indd 9 3/14/11 10:42:24 AM3/14/11 10:42:24 AM

10

■ Title/Chapter/Track PC-created disc

• You may not be able to play discs recorded

using a personal computer or recorder for disc

compatibilities, scratches or marks on the disc, dirty

lenses of the unit or condensation and so on.

• Discs recorded using a personal computer may

not be playable in this unit due to the setting of the

application software used to create the disc. In

these particular instances, check with the software

publisher for more detailed information.

■ Playable files

• ISO 9660 Level 1 or 2 compliant.

Romeo and Joliet file systems are both compatible

with this player.

• DRM (Digital Rights Management) protected files

will not play in this player.

For detailed information, please see the instruction

manuals or help files that came with your PC and/or

software.

• File structure (may differ): Up to 299 folders on a

disc; up to 648 files within each folder

• Folder and file names can be displayed as long

as they are typed in alphabets and numbers. If

folder and file names are other than alphabets and

numbers, they may be replaced and displayed like

as “_”. Garbled characters may also be displayed in

this case.

■ Playing image files

JPEG files recorded in DVD-R/-RW and CD-R/-RW

can be played.

■ JPEG file compatibility

• Image files should be saved in JPEG format.

• Files recorded in Fuji Color CD, Kodak Picture CD

or CD-R/-RW can be played.

• Compatible formats: Baseline JPEG and EXIF 2.2*

still image files up to a resolution of 3072 x 2048.

*File format used by digital still cameras.

• Files with extensions .jpg or .JPG can be played.

• Progressive JPEG formatted files do not work.

• It may take some more time to start to play larger

files than usual.

• JPEG files with different aspect ratio may be

displayed with black bands (either vertical or

horizontal).

■ Playing Audio files

WMA and MP3 files recoded in DVD-R/-RW, CD-R/-

RW can be played.

■ Windows Media Audio (WMA)

compatibility

• WMA is an acronym for Windows Media Audio

and refers to an audio compression technology

developed by Microsoft Corporation.

• You can encode your files by using Windows

Media Player Ver.7, 7.1, Windows Media Player for

Windows XP or Windows Media Player 9 Series.

• When encoding your files, use only applications

approved by Microsoft Corporation. If you use a

non-approved application, it may not work properly.

• This unit is compatible with audio files recorded with

the following sampling frequency: 32 kHz, 44.1 kHz

and 48 kHz.

• It is not compatible with loss-less encoding.

• Files with extensions .wma or .WMA can be played.

■ Playing MP3 (MPEG-1 Audio Layer-3) files

• This unit is compatible with audio files recorded with

the following sampling frequency: 32 kHz, 44.1 kHz

and 48 kHz.

• Files with extensions .mp3 or .MP3 can be played.

• For the best quality of sound, 128 kbps or higher bit

rate is recommended.

■ Copy Control CD (CCCD)

This product is designed to conform to CD-DA

(Compact Disc Digital Audio). Any other discs than

CD-DA are not guaranteed with their operation and

performance in this product.

Note on copyright

• Unauthorized recording of copyrighted television

programs, films, video cassettes and other materials

may infringe the rights of copyright owners and be

contrary to copyright laws.

Disc (continued)

57A0221A_eng.indd 1057A0221A_eng.indd 10 3/14/11 10:42:25 AM3/14/11 10:42:25 AM

11

ENGLISH

Left side

Front

Remote sensor

Rear

To display the menu screen.

Touch and hold both VOL (VOLUME) +/– at the same time for 1 second to display the menu screen.

CH (CHANNEL)

/ buttons,

VOL (VOLUME) +/– buttons and INPUT/ENTER button can be used to select the

desired setting during the menu screen operations.

PC MONITOR IN jack

VIDEO IN jacks

(VIDEO/AUDIO

(L (MONO)/R))

HDMI/DVI

IN jack

PC/DVI AUDIO IN jack

Parts and functions

COMPONENT

IN jacks

ANT. (RF) IN jack

HEADPHONE jack

Indicator

Red : Standby

Blue : On

AC INPUT jack

Right side

DIGITAL AUDIO

COAXIAL OUT jack

FOR SERVICE PERSONNEL USE ONLY

Do NOT insert ANY USB device into

this port. Use of this port by other than

Service Personnel may void this products

warranty.

EJECT button

INPUT/ENTER button

CH (Channel)

/

▶

(Play) button

CH (Channel)

/ (Stop) button

VOL (Volume) +/

–

buttons

POWER button

57A0221A_eng.indd 1157A0221A_eng.indd 11 3/14/11 10:42:26 AM3/14/11 10:42:26 AM

12

Remote control

POWER Power On/Off

DISPLAY/– Call TV information

Call DVD information

Input “–” for digital channels

TV/DVD Switch between TV and DVD

(EJECT) Eject a disc

0-9 Direct channel selection of TV

Input setting

Enter a password

VOL +/– Adjust volume of TV

MUTING Switch off the sound

SLEEP Sleep timer

SETUP/

TV MENU

DVD mode - Call up initial setup mode

TV mode - Display menu of TV

DVD MENU Display DVD menu

CH

/

Select channel of TV

▲▼◀▶ Cursor buttons

ENTER Enter information in the menu

EXIT/

CANCEL

Exit from On-Screen menu

Reset information in the menu

TOP MENU Select title

SEARCH Fast Forward/Review playback

PLAY Power On : Start playback

Standby mode : Power On and start playback

SKIP Skip chapter to forward or reverse direction

SUBTITLE Set subtitle

STOP Stop

SLOW Forward/Reverse- slow motion

PAUSE/

STILL

Pause CD sound

Still picture of DVD

PLAY MODE Select playback mode

AUDIO Change soundtrack language

RETURN Remove DVD setup menu

REPEAT A-B Repeat playback between A and B

ANGLE Change playback angle

SCREEN SIZE Display Picture Size menu

MARKER Index

CCD/

JUMP

Closed Caption

Locating desired scene

RECALL/

ZOOM

Switch between present/last channel

Zoom

INPUT SELECT Display source selection menu

57A0221A_eng.indd 1257A0221A_eng.indd 12 3/14/11 10:42:31 AM3/14/11 10:42:31 AM

13

ENGLISH

Approximately 15 feet

Inserting Batteries

1

Open the battery compartment

cover in the direction of the arrow.

2

Install two “AAA” batteries

(supplied), paying attention

to the polarity diagram in the

battery compartment.

3

Replace the compartment cover.

Operation

Aim the remote control at the remote sensor and press control

buttons to operate.

Operate the remote control within a 30° angle on either side of

the remote sensor, up to a distance of approximately 15 feet.

•

Remote control (continued)

BATTERY PRECAUTIONS:

Batteries should not be exposed to excessive heat such as sunshine, fire or the like.

The remote control unit uses infrared beams to transmit signals, so sunlight or fluorescent light on the remote

sensor may shorten operating distance.

Incorrect use of batteries may cause them to leak or burst. Read the battery warnings and use the batteries

properly.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

Remove batteries if the remote control will not be operated for an extended period of time.

•

Power source

TO USE AC POWER

Connect the AC cord plug into this unit’s AC INPUT jack.

Connect the AC cord into an AC outlet.

1.

2.

NOTE:

Please make sure to insert the cord securely at both the LCD TV/DVD and the wall outlet.

The AC Cord has a polarized type AC line plug. If the supplied AC cord does not match your AC outlet,

contact a qualified electrician.

WARNING:

DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC

CORD. THIS COULD CAUSE FIRE, ELECTRICAL SHOCK, OR DAMAGE.

DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE SPECIFIED. THIS COULD CAUSE

FIRE, ELECTRICAL SHOCK, OR DAMAGE.

CAUTION:

WHEN THIS UNIT IS NOT USED FOR A LONG TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF

SAFETY, BE SURE TO UNPLUG IT FROM THE AC OUTLET.

DO NOT PLUG/UNPLUG THE AC CORD WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRICAL

SHOCK.

IF YOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED ONE IS

RECOMMENDED. CONTACT CUSTOMER SERVICE AT 1-800-289-0984.

•

If this symbol is shown, it is only

valid in the European union.

AC cord (supplied)

AC 120V, 60Hz

Wider Hole

and Blade

AC Outlet

57A0221A_eng.indd 1357A0221A_eng.indd 13 3/14/11 10:42:31 AM3/14/11 10:42:31 AM

14

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your

antenna system. If you are using a Cable TV service, see “Cable TV connections”.

Combination VHF/UHF Antenna (Single 75 ohm cable)

Antenna

Jack

75 ohm

Coaxial

Cable

Connect the 75 ohm cable from the combination

VHF/UHF antenna to the Antenna Jack.

Cable TV connections

For basic Cable TV service not requiring a Converter/

Descrambler box, connect the 75 ohm Coaxial Cable directly

to the Antenna Jack on the back of the TV.

For subscribers to scrambled Cable TV service

If you subscribe to a Cable TV service which requires the use of a Converter/Descrambler box, connect

the incoming 75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial

Cable, connect the output jack of the Converter/Descrambler box to the Antenna Jack on the TV. Follow the

connections shown below. Set the TV to the output channel of the Converter/Descrambler box (usually channel

3 or 4) and use the Converter/Descrambler box to select channels.

For subscribers to unscrambled Cable TV service with scrambled premium

channels

If you subscribe to a Cable TV service in which basic channels are unscrambled and premium channels require

the use of a Converter/Descrambler box, you may wish to use a signal Splitter and an A/B Switch box (available

from the Cable TV company or an electronics supply store). Follow the connections shown below. With the

switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the

“A” position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the

Converter/Descrambler box to tune scrambled channels.

This TV has an extended tuning range and can tune most cable channels without using a Cable TV

Converter box. Some cable companies offer “premium pay channels” where the signal is scrambled.

Descrambling these signals for normal viewing requires the use of a descrambler device which is

generally provided by the Cable TV company.

For subscribers to basic Cable TV service

Incoming

75 ohm

Cable TV

Cable

75 ohm Cable to TV

Antenna

Jack

Converter/

Descrambler

Splitter

B

A

Incoming

75 ohm

Cable TV

Cable

A/B Switch

75 ohm Cable to TV

Converter/

Descrambler

Antenna

Jack

Antenna

Jack

75 ohm

Coaxial

Cable

57A0221A_eng.indd 1457A0221A_eng.indd 14 3/14/11 10:42:32 AM3/14/11 10:42:32 AM

15

ENGLISH

Starting setup

The Auto Setup menu appears the first time you

turn on the TV, and assists you to specify the

Air/Cable setting, and program your channels

automatically.

IMPORTANT: Make sure that the antenna or cable

TV system connection is made!

1

To turn on the TV, press POWER (POWER

indicator on the front of the unit changes blue.

It may take approx. 10 seconds for a picture to

appear on screen.). The Auto Setup function

begins.

Auto Setup

Signal Type Cable

Automatic Search Start

2

Press ◀ or ▶ to select “Cable” or “Air”.

3

Press ▲ or ▼ to select “Automatic Search”, then

press ▶ or ENTER.

4

“Auto Setup” will begin. After the Auto Setup

is completed, the TV channel appears on the

screen.

Depending on the reception condition, it may

take up to 30 minutes to complete memorizing

digital cable channels. Please allow the

process to complete without interruption.

•

NOTE:

If you press EXIT/CANCEL in the process of “Auto

Setup”, the Auto Setup stops and changes to the

normal screen.

When you make a menu selection, your changes

occur immediately. You do not have to press EXIT/

CANCEL to see your changes.

TV operation

1

To turn on the TV, press

POWER. (POWER

indicator on the front of the unit changes blue.

It may take approx. 10 seconds for a picture to

appear on screen.)

2

Adjust the volume level by pressing VOL + or – .

The volume level will be indicated on the screen

by green bars. As the volume level increases, so

do the number of bars. If the volume decreases,

the number of green bars also decreases.

3

Set the Signal Type option to the appropriate

position (see “Air/Cable selection” on page 18).

4

Press the Direct Channel Selection (0-9, –)

buttons to select the channel.

(If you press only channel number, channel

selection will be delayed for a few seconds.)

•

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to

select channel 2, press 2, then press

ENTER.

10-99: Press the 2 digits in order. Example,

to select channel 12, press 1, 2, then

press ENTER.

100-135: Press the 3 digits in order. Example, to

select channel 120, press 1, 2, 0, then

press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the – button,

followed by the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1,

then press ENTER.

If a channel is selected with only audio content,

“Audio only” will be displayed on the screen.

If a channel is selected with a weak digital

signal, “Digital channel signal strength is low”

will be displayed on the screen.

The same program may be available on either

an analog channel or a digital channel. You may

choose to watch either format.

If a channel is selected to which you have not

subscribed,

“Digital channel is encrypted” will

be displayed on the screen.

•

VHF/UHF/CABLE CHANNELS

Air Cable

VHF

2-13

VHF

2-13

UHF

14-69

STD/HRC/IRC

14-36 (A) (W)

37-59 (AA) (WW)

60-85 (AAA) (ZZZ)

86-94 (86) (94)

95-99 (A-5) (A-1)

100-135 (100) (135)

01 (4A)

NOTE:

If a channel with no broadcast is selected, the

sound will automatically be muted.

It may take a few seconds for a digital channel

picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to

your LCD TV, such as a VCR player, press INPUT

SELECT, then press ▲ or ▼ or corresponding

Number buttons (0-5), then press ENTER. You

can select TV, Video, Component, HDMI, PC or DVD

depending on which input jacks you used to connect

your devices.

Input Select

0.TV

1.Video

2.Component

3.HDMI

4.PC

5.DVD

[0-5]:Select

CH /

Press and release CH / . The channel

automatically stops at the next channel set into

memory.

For proper operation, before selecting channels, they

should be set into the memory. See “Memorizing

channels” on page 18.

•

57A0221A_eng.indd 1557A0221A_eng.indd 15 3/14/11 10:42:34 AM3/14/11 10:42:34 AM

16

DISPLAY

Press DISPLAY to display the current information on

the screen.

When the TV receives a digital signal, the digital

information will appear.

62-1 HDTV_Moving_Picture...

CH-1 TV-MA

Digital Air

No Program Information is available

Sleep Timer

Off

English

Full

1080i

Channel number• Station name•

Channel label (if preset)•

Broadcast program name

•

V-Chip rating• Signal type•

Sleep timer• Audio language•

Program guide• Picture size•

Resolution•

When the TV receives an analog signal, the analog

information will appear.

14

Analog Cable

Sleep Timer

Off

Mono

Full

480i

G

Channel number• Channel label (if preset)•

V-Chip rating• Signal type•

Sleep timer• Picture size•

Audio information

(Stereo, SAP or Mono)

• Resolution•

Press DISPLAY again to clear the call display.

NOTE:

After a few seconds, DISPLAY screen will return to

normal TV operation automatically.

RECALL

This button allows you to go back to the last channel

selected by pressing RECALL. Press RECALL again to

return to the last channel you were watching.

MUTING

Press MUTING to switch off the sound. The TV’s

sound will be silenced and “Muting” will appear on

the screen. The sound can be switched back on by

pressing this button again or the VOL + or –.

SLEEP

To set the TV to turn off after a preset amount of time,

press SLEEP on the remote control. The clock will

count up 10 minutes for each press of the SLEEP but-

ton (Off, 0h 10m, 0h 20m, ..., 2h 0m). After the sleep

time is programmed, the display will appear briefly

every ten minutes to remind you that the sleep timer

is operating. To confirm the sleep timer setting, press

SLEEP and the remaining time will be displayed for a

few seconds. To cancel the sleep timer, press SLEEP

repeatedly until the display turns to Off.

•

Quick guide for menu

operation

Call menu and for example: Select Language.

1

Press INPUT SELECT to select TV mode.

2

Press TV MENU. The TV menu screen will appear.

Audio

Channel

Lock

Setup

Main Menu

Picture

>>

ENTER :Set:Select

CH

3

Press ▲ or ▼ to select “Setup”, then press ▶ or

ENTER.

4

Press ▲ or ▼ to select “Language”, then press ◀

or ▶ to select the desired language.

…on the following pages the menu can be called

in the same way as here.

5

Press EXIT to return to the normal screen.

NOTE:

If no buttons are pressed for more than about 60

seconds, the menu screen will return to normal

operation automatically.

•

57A0221A_eng.indd 1657A0221A_eng.indd 16 3/14/11 10:42:36 AM3/14/11 10:42:36 AM

17

ENGLISH

Convenience functions

You can change the default settings by pressing the TV MENU button on your remote, then select the one of the

icons at the left of the menu - follow the On-Screen prompts to set your preferences.

Icon Selected Items Setup hint

Picture Picture

Preference

Sports Bright and dynamic picture (factory-set)

Standard Standard picture quality (factory-set)

Movie Movie-like picture setting (factory-set)

Memory Your personal preferences (set by you; see “Picture Setting”)

Picture Setting Brightness /Contrast /

Sharpness / Color / Tint

You can adjust the picture quality to your preference.

Color Temperature Bluish (Cool) / Neutral (Standard) / Reddish (Warm)

Backlight The Backlight feature adjusts the screen brightness for improved

picture clarity.

DBC On/Off

Use this feature to change the Black level automatically according to the

brightness of an image. The Black level will become dark in a dark scene.

Picture Size See page 22.

Film Mode On/Off A smoother motion may be obtained by setting the Film Mode to “On”

(480i only).

PC Setting Hor Position /

Ver Position

To adjust the horizontal / vertical position of the image on the PC monitor

screen. Each video standard will require a different value for this setting.

Clock

To minimize any vertical bars or stripes visible on the screen background.

Phase

This must be adjusted after the frequency has been set optimize picture quality.

Auto Adjust To adjust the all PC settings automatically.

DNR On/Off DNR (Digital Noise Reduction) can reduce the roughness of the picture.

Audio

Equalizer Mode

Standard/Music/Movie/

News/Memory/Flat

You can adjust the Equalizer Mode to your preference.

Audio Setting Bass/Treble You can adjust the sound quality to your preference. (Flat mode only)

Equalizer Setting

100Hz/250Hz/500Hz/1kHz/2kHz/4kHz/10kHz (Not available in Flat mode)

Balance You can adjust the sound quality to your preference.

MTS Stereo / SAP / Mono The multi-channel TV sound (MTS) feature provides high-fidelity

stereo sound. MTS also can transmit a second audio program (SAP)

containing a second language or other audio information.

When the TV receives a stereo or SAP broadcast, the word “Stereo” or

“SAP” displays on-screen every time you press DISPLAY.

Surround On/Off The dynamic presence and sound created offers a thoroughly

enjoyable listening experience.

Auto Volume On/Off Volume level can be adjusted automatically by the sound level.

Audio Language

When two or more audio languages are included in a digital signal, you can select

one of the audio languages. (This function is available only for digital broadcast.)

HDMI Audio HDMI When you connect the HDMI device to the TV, select this setting.

DVI When you connect the DVI device to the TV with analog audio cords,

select this setting.

Channel Add / Delete See page 18.

DTV Signal See page 19.

Auto Ch Memory See page 18.

Ch Label See page 19.

Lock See page 20.

Setup Closed Caption See page 21.

Language

You can choose from three different languages (English, Français (French) and

Español (Spanish)) for the on-screen displays.

Select the language you prefer first, then proceed with the other menu options.

Video Label See page 19.

On Timer Off / 0h30m / 1h00m

/ 1h30m / 2h00m /

3h00m⋅⋅⋅12h00m

You can set the On Timer to automatically turn on the TV. To cancel the

On Timer select “Off”.

Auto Shut Off*

On/Off If the Auto Shut Off feature is On, a station being viewed stops

broadcasting and the TV is not operated, the TV will automatically shut

itself off after 15 minutes.

Power On/Off

Sound

On/Off When you turn on/off the TV, sound will output from TV.

Power On LED

On/Off

When you turn on the TV, Power indicator on the front of the TV will light.

PC Standby On/Off

If the PC Standby feature is On. In PC mode, if no signal is received or

no operation performed for 1 minute, the TV will turn to standby mode

automatically (LED light will flash red). When an input signal is received

or an operation performed on the PC, the TV will return to the On mode.

Reset

The Reset function returns your Picture/Audio settings to the factory settings.

“Picture Size”, “MTS” , “Audio Language” and “HDMI Audio” cannot be

reset by this function.

NOTE:

* If there is no input signal in the PC mode, after 1 minute Auto Shut Off will be activated.

57A0221A_eng.indd 1757A0221A_eng.indd 17 3/14/11 10:42:37 AM3/14/11 10:42:37 AM

18

Memorizing channels

This TV is equipped with a channel memory

feature which allows channels to skip up or down

to the next channel set into memory, skipping

over unwanted channels. Before selecting

channels, they must be programmed into the

TV’s memory. To use this TV with an antenna, set

the Signal Type option to the Air mode. When

shipped from the factory, this menu option is in

the Cable mode.

Air/Cable selection

1

Select “Channel”, then press ▶ or ENTER.

2

Press ▲ or ▼ to select “Auto Ch Memory”, then

press ▶ or ENTER.

3

Press ▲ or ▼ to select “Signal Type”.

4

Press ◀ or ▶ to select “Air” or “Cable”.

Air - VHF/UHF channels

Cable - CABLE TV channels

Automatic Search Start

Auto Ch Memory

Signal Type Cable

:Adjust

:Select

CH

CABLE CHART

The chart below is typical of many cable system

channel allocations.

NOTE:

It may take a few seconds for a digital channel

picture to appear on screen after being selected.

Automatic Search

1

Select “Channel”, then press ▶ or ENTER.

2

Press ▲ or ▼ to select

“Auto Ch Memory”, then

press

▶

or ENTER.

3

Press ▲ or ▼ to select “Automatic Search”, then

press ▶ or ENTER.

Auto Ch Memory

Signal Type Cable

Digital Channel Found : 0

Analog Channel Found : 0

Programming Now

Automatic Search Stop

ENTER :Cancel:Select

CH

•

4

The TV will begin memorizing all the channels

available in your area.

It may take from 15 minutes to 30 minutes to

complete memorizing digital cable channels.

Depending on the reception condition, a bar

display may not advance for several minutes,

please be patient.

•

NOTE:

Memorizing channels is best accomplished during

evening “PRIMETIME” hours, as more stations are

broadcasting digital signals. Memorizing channels can

only be accomplished while a station is broadcasting

a digital signal to set that channel into memory.

If you are unsure of the digital channels available

in your area, you may visit www.antennaweb.org to

receive a list based on your address or zip code.

Should you require further assistance you may call

our toll-free customer service line at 1-800-289-0984.

New digital channels may be added to your area

periodically, it is recommended to perform the

“Automatic Search” procedure regularly.

Adding Channel

If you find a new digital channel unregistered, you can

add the new channel into the channel memory.

1

Tune in the new channel.

2

Select “Channel”, then press ▶ or ENTER.

3

Press ▲ or ▼ to select “Add/Delete”, then press ▶

or ENTER.

Add/Delete

Adding Channel >>

Clear All >>

Add/Delete >>

ENTER :Set:Select

CH

4

Press ▲ or ▼ to select “Adding Channel”, then

press ▶ or ENTER. The new channel will be

added into the channel memory.

Add/Delete channel

You can select the channel that you want to skip.

1

Select “Channel”, then press ▶ or ENTER.

2

Press ▲ or ▼ to select “Add/Delete”, then press ▶

or ENTER.

3

Press ▲ or ▼ to select “Add/Delete”, then press ▶

or ENTER.

4

Press ▲ or ▼ to select the channel that you want

to skip.

CH

Signal

2 Analog

3

3-1

3-2

Analog Add

Digital Delete

Digital Add

4 Analog Delete

Add/Delete

Add

:Adjust

:Select

CH

5

Press ◀ or ▶ to select “Add” or “Delete”,

whichever function you want to perform.

6

Repeat steps 4 - 5 for other channels you want to

add or delete.

•

57A0221A_eng.indd 1857A0221A_eng.indd 18 3/14/11 10:42:38 AM3/14/11 10:42:38 AM

19

ENGLISH

Clear All

All channels are deleted from the channel memory.

1

Select “Channel”, then press ▶ or ENTER.

2

Press ▲ or ▼ to select “Add/Delete”, then press ▶

or ENTER.

3

Press ▲ or ▼ to select “Clear All”, then press ▶ or

ENTER.

Add/Delete

Adding Channel >>

Clear All >>

Add/Delete >>

ENTER :Set:Select

CH

Checking the digital

signal strength

This TV will allow you to view the digital signal

meter for digital channels.

1

Select “Channel”, then press ▶ or ENTER.

2

Press ▲ or ▼ to select “DTV Signal”.

3

Press ▶ or ENTER to check the digital signal

strength.

The digital signal strength screen will appear.

If necessary, adjust the direction of the antenna to

obtain the maximum signal strength.

Signal Level

0 50 100

DTV Signal

CH

NOTE:

Signal meter feature is not available for analog

channels.

After 240 seconds, DTV Signal screen will return to

normal TV operation automatically.

•

Labeling channels

Channel label appear with the channel number

display each time you turn on the TV, select a

channel, or press DISPLAY.

You can choose any four characters to identify a

channel.

To create channel labels

1

Select “Channel”, then press ▶ or ENTER.

2

Press ▲ or ▼ to select “Ch Label”, then press ▶

or ENTER.

The Ch Label menu will appear.

3

Press ◀ or ▶ to select a channel you want to

label, then press ▼.

Ch Label

Label Clear

>>

Ch Label

Channel Number

15-1

CH-1

:Adjust

:Select

CH

4

Press ◀ or ▶ repeatedly until the character you

want appears in the first space.

Label Clear >>

Ch Label

Channel Number 15-1

Ch Label

CH-1

:Adjust

:Select

ENTER :Set

CH

The characters rotation as follows:

SPACE

-

, () @ / + =

-

If the character which you desire appears, press

ENTER.

Repeat this step to enter the rest of the characters.

If you would like a blank space in the label name,

you must choose the empty space from the list of

characters.

5

Repeat steps 3-4 for other channel. You can

assign a label to each channel.

6

When you finish inputting the label name, press

EXIT to return to the normal screen.

To clear a Ch Label

After step 3 above, press ▲ or ▼ to select “Label

Clear”, then press ▶ or ENTER.

NOTE:

The channel labels will be reset after “Automatic

Search” on page 18.

Labeling video inputs

The Video Label feature allows you to label each

input source for your TV.

1

Select “Setup”, then press ▶ or ENTER.

2

Press ▲ or ▼ to select “Video Label”, then press

▶ or ENTER.

3

Press ▲ or ▼ to select an input which you want to

label.

4

Press ◀ or ▶ to select the desired label for that

input source.

Component -

HDMI -

PC -

Video Label

Video -

:Adjust

:Select

– / VCR / DVD / STB / Cable / Satellite / Receiver /

Game / Camcorder / PC / DVI PC / Blu-ray

•

57A0221A_eng.indd 1957A0221A_eng.indd 19 3/14/11 10:42:39 AM3/14/11 10:42:39 AM

20

Setting the V-Chip

An age limitation can be set to restrict children from

viewing or hearing violent scenes or pictures that you

may choose to exclude. The restriction applies to “TV

Rating” and “Movie Rating” if this data is transmitted.

You may set this restriction separately. To use the

V-Chip function, you must register a password.

To register a password

1

Select “Lock”, then press ▶ or ENTER.

2

Select and enter your password (4 digits) using

Number buttons (0-9), then press ENTER.

Lock

New Password

* * *

_

:Enter Code

[0-9]

ENTER :Set

“ ” appears instead of the number.

3

Enter the same password again to confirm, then

press ENTER.

The password is now registered.

NOTE:

If you forget the password, contact Customer

Service at 1-800-289-0984 for assistance.

Your original remote control will be required.

To avoid forgetting the password, write it down and

keep in a safe place.

To set the V-Chip

1

Select “Lock” menu, then press ▶ or ENTER.

2

Use Number buttons (0-9) to enter your

password, then press ENTER. The Lock menu

will appear.

3

Press ◀ or ▶ to set “V-Chip” to “On”.

4

Press ▲ or ▼ to select “V-Chip Set”, then press ▶

or ENTER.

The V-Chip Set menu will appear.

5

Press ▲ or ▼ to select which rating will be used,

then press ▶ or ENTER. Each rating below will

appear.

TV Rating

TV-Y

TV-Y7

TV-G

TV-PG

TV-14

TV-MA

TV Rating

ENTER :Set

:Select

You can set the rating using age level and genre.

Age:

TV-Y : All children

TV-Y7 : 7 years old and above

TV-G : General audience

TV-PG : Parental guidance

TV-14 : 14 years old and above

TV-MA : 17 years old and above

•

When you select TV-Y7, TV-PG, TV-14 or TV-MA,

press DISPLAY to explain the rating.

Genre:

D : Dialogue

L : Language

S : Sex

V : Violence

FV : Fantasy Violence

Movie Rating

G

PG

PG-13

R

NC-17

X

Movie Rating

ENTER :Set:Select

G : All ages

PG : Parental guidance

PG-13 : Parental guidance

less than 13 years old

R : Under 17 years old parental guidance

suggested

NC-17 : 17 years old and above

X : Adult only

6

Press ▲ or ▼ to select the desired rating, then

press ENTER.

7

Press EXIT to return to the normal screen.

V-Chip function is activated now.

To use the TV after the TV is protected.

When a program is received that is blocked by the

V-Chip, press MUTING, then enter your password.

The protection will be temporarily overridden. If the

TV is turned off or the channel is changed, the V-Chip

restriction will be reactivated.

NOTE:

The V-Chip function is activated only on programs

and input sources that include a rating signal.

To change the password

1

Select “Lock”, then press ▶ or ENTER.

2

Use Number buttons (0-9) to enter your password,

then press ENTER. The Lock menu will appear.

3

Press ▲ or ▼ to select “Change Password”, then

press ▶ or ENTER.

The Change Password screen will appear.

4

Enter a new password using Number buttons

(0-9), then press ENTER.

5

Enter the same password again to confirm, then

press ENTER.

The password is now registered.

Downloading the additional V-Chip rating system

As a supplement to the standard V-Chip rating

system, your television will be able to download an

additional rating system, if such a system becomes

available in the future.

To download the additional V-Chip rating system

(when available)

1

Select “Lock”, then press ▶ or ENTER.

2

Use Number buttons (0-9) to enter your password,

then press ENTER. The Lock menu will appear.

•

57A0221A_eng.indd 2057A0221A_eng.indd 20 3/14/11 10:42:40 AM3/14/11 10:42:40 AM

La page charge ...

JVC LT-22DE72 Instructions Manual

JVC LT-22DE72 Instructions Manual

dans d''autres langues

Documents connexes

Autres documents