Samsung WA45H7000AW/A2 Le manuel du propriétaire

Washing Machine

user manual

WA48H7400A*

WA45H7200A*

WA45H7000A*

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory

parts, please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

This manual is made with 100% recycled paper.

English - 2

contents

INSTALLING YOUR WASHER

10

10 Unpacking your washer

10 Overview of your washer

11 Basic location requirements

11 Electrical

11 Grounding

11 Water

12 Drain facility

12 Flooring

12 Location considerations

12 Alcove or closet installation

13 Required dimensions for Installation

13 Important note to installer

OPERATING INSTRUCTIONS

17

17 Loading your washer

17 Getting started

WASHING A LOAD OF LAUNDRY

18

18 Overview of the control panel

20 Child Lock [

]

21 Sound

21 Garment

21 Delay End

21 Pre Soak

21 AquaJet

TM

22 Mist Shower

22 Smart Care

23 Washing clothes using the cycle selector

23 ATC (Auto Temperature Control)

24 Detergent use

24 Features

MAINTAINING YOUR WASHER

27

27 Cleaning the exterior

27 Cleaning the interior

27 Storing your washer

27 Preserving the top cover and the front frame

28 Cleaning the dispensers

29 Self Clean

TROUBLESHOOTING

30

30 Check these solutions if your washer…

32 Information codes

APPENDIX

34

34 Fabric care chart

35 Cycle chart

38 Helping the environment

38 Declaration of conformity

38 Speciﬁcation

English - 3

safety information

Congratulations on your new Samsung Washer. This manual contains important

information on the installation, use, and care of your appliance. Please take time

to read this manual to take full advantage of your washer’s many beneﬁts and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, and operating your washer.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

To reduce the risk of ﬁre, explosion, electric shock, or personal injury

when using your washer, follow these basic safety precautions:

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning icons are here to prevent injury to you and others.

Please heed them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

SAVE THESE INSTRUCTIONS

English - 4

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using the appliance.

2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked

in, or spotted with gasoline, dry-cleaning solvents, other ﬂammable or explosive

substances as they give o vapors that could ignite or explode.

3. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

4. Before the appliance is removed from service or discarded, remove the lid of the

washing or drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to the weather.

7. Do not tamper with the controls.

8. Do not repair or replace any part of the appliance or attempt any servicing unless it is

speciﬁcally recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

9. Do not add gasoline, dry-cleaning solvents, or other ﬂammable or explosive substances

to the wash water. These substances give o vapors that could ignite or explode.

10. Under certain conditions, hydrogen gas may be produced in a hot water system that

has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the

hot water system has not been used for 2 weeks or more, before using a washer or

combination washer-dryer, turn on all hot water faucets and let the water ﬂow from

each for several minutes. This will release any accumulated hydrogen gas. As the gas is

ﬂammable, do not smoke or use an open ﬂame during this time.

State of California Proposition 65 Warnings:

WARNING: This product contains chemicals known to the State of California to cause

cancer and reproductive toxicity.

SAVE THESE INSTRUCTIONS

safety information

WARNING

English - 5

CRITICAL INSTALLATION WARNINGS

Plug the power cord into an AC 120 V / 60 Hz/wall socket rated at 15 amps or higher. Use

the socket for this appliance only. In addition, do not use an extension cord.

- Sharing a wall socket with other appliances, using a power strip, or extending the power

cord may result in electric shock or ﬁre.

- Do not use an electric transformer. It may result in electric shock or ﬁre.

- Ensure that the power voltage, frequency, and current match the product’s

speciﬁcations. Failing to do so may result in electric shock or ﬁre.

Have this appliance installed by a qualiﬁed technician or service company.

- Failing to do so may result in electric shock, ﬁre, an explosion, problems with the

product, or injury.

Remove all foreign substances such as dust or water from the power plug terminals and

contact points using a dry cloth on a regular basis.

- Unplug the power plug and clean it with a dry cloth.

- Failing to do so may result in electric shock or ﬁre.

Plug the power plug into the wall socket in the right direction so that the cord runs towards

the ﬂoor.

- If you plug the power plug into the socket in the opposite direction, the electric wires

within the cable may be damaged and this may result in electric shock or ﬁre.

This appliance must be properly grounded.

Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.

- Improper grounding may result in electric shock, ﬁre, an explosion, or problems with the

product

- Never plug the power cord into a socket that is not grounded correctly. Make sure the

socket you use is grounded in accordance with local and national codes.

Do not install this appliance near a heater or inﬂammable material.

Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to

direct sunlight or water (rain drops).

Do not install this appliance in a location where gas may leak.

- This may result in electric shock or ﬁre.

Plug the power plug into the wall socket ﬁrmly. Do not use a damaged power plug,

damaged power cord, or loose wall socket.

- This may result in electric shock or ﬁre.

Do not pull or excessively bend the power cord.

Do not twist or tie the power cord.

Do not hook the power cord over a metal object, place a heavy object on the power cord,

insert the power cord between objects, or push the power cord into the space behind the

appliance.

- This may result in electric shock or ﬁre.

Do not pull the power cord when unplugging the power plug.

- Unplug the power plug by holding the plug.

- Failing to do so may result in electric shock or ﬁre.

If the power plug or power cord are damaged, contact your nearest service center.

SAVE THESE INSTRUCTIONS

WARNING

English - 6

INSTALLATION CAUTIONS

Position the appliance so that the power plug is easily accessible.

- Failing to do so may result in electric shock or ﬁre due to electric leakage.

Install your appliance on a level and hard ﬂoor that can support its weight.

- Failing to do so may result in abnormal vibrations, noise, or problems with the product.

Unplug the power plug when the appliance is not being used for long periods of time or

during a thunder/lightning storm.

- Failing to do so may result in electric shock or ﬁre.

CRITICAL USAGE WARNINGS

If the appliance is ﬂooded, cut the power immediately and contact your nearest service

center.

If the appliance emits a strange noise, a burning smell, or smoke, unplug the power plug

immediately and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁre.

In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area

immediately. Do not turn any appliance or light on or o.

- Do not use a ventilating fan.

- A spark may result in an explosion or ﬁre.

Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or

other ﬂammable or explosive substances.

- This may result in electric shock, ﬁre, or an explosion.

Do not force the washer lid open while the washer is operating (high-temperature washing/

drying/spinning).

- Water ﬂowing out of the washer may cause burns or cause the ﬂoor to be slippery.

This may result in injury.

- Forcing the lid open can damage the product or cause injury.

Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the

washer before using it.

Do not insert your hand under the washer.

- This may result in injury.

safety information

SAVE THESE INSTRUCTIONS

WARNING

CAUTION

English - 7

Do not touch the power plug with wet hands.

- This may result in electric shock.

Do not turn the appliance o by unplugging the power plug while the washer is in operation.

- Plugging the power plug into the wall socket again may cause a spark and result in

electric shock or ﬁre.

Keep all packaging materials well out of the reach of children, as packaging materials can

be dangerous to children.

- If a child places a bag over its head, it may suocate.

Do not let children or inﬁrm persons use this washer unsupervised.

- Failing to do so may result in electric shock, burns or injury.

Do not insert your hand or a metal object under the washer while it is operating.

- This may result in injury.

Do not attempt to repair, disassemble, or modify the appliance yourself.

- Do not use any fuse (such as cooper, steel wire, etc.) other than the standard fuse.

- If you need to repair or reinstall the appliance, contact your nearest service center.

- Failing to do so may result in electric shock, ﬁre, problems with the product, or injury.

If any foreign substance such as water enters the appliance in any area other than the tub,

unplug the power plug and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁre.

If the water supply hose comes loose from the faucet and ﬂoods the appliance, unplug the

power plug.

- Failing to do so may result in electric shock or ﬁre.

USAGE CAUTIONS

If the washer is contaminated by a foreign substance such as detergent, dirt, food waste,

etc., unplug the power plug and clean the washer using a damp, soft cloth.

- Failing to do so may result in discoloration, deformation, damage or rust.

The clear portion of the lid can be broken by a strong impact. Take care when using the

washer.

- If the clear portion is cracked or broken, it may result in injury.

After a water supply failure or when reconnecting the water supply hose, open the faucet

slowly.

Open the faucet slowly after a long period of non-use.

- The air pressure in the water supply hose or the water pipe may result in damage to a

part or in water leakage.

If a drain error occurs during an operation, check if there is a draining problem.

- If the washer is used when it is ﬂooded because of a draining problem, it may result in

electric shock or ﬁre due to electric leakage.

Do not insert your hand under the washer.

- This may result in injury.

SAVE THESE INSTRUCTIONS

CAUTION

English - 8

Insert the laundry into the washer completely so that laundry does not get caught in the lid.

- If laundry gets caught in the lid, it may result in damage to the laundry or the washer, or

result in water leakage.

Ensure that the faucet is turned o when the washer is not being used.

- Ensure that the water supply hose connectors are properly tightened.

- Failing to do so may result in property damage or injury.

Open the faucet and check if the water supply hose connector is ﬁrmly tightened and that

there is no water leaking before using the product.

- If the water supply hose connectors are loose, it may result in water leakage.

Do not stand on top of the appliance or place objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.

- This may result in electric shock, ﬁre, problems with the product, or injury.

Do not operate the appliance with wet hands.

- This may result in electric shock.

Do not spray volatile material such as insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may also result in electric shock, ﬁre,or problems

with the product.

Do not place an object that generates a electromagnetic ﬁeld near the washer.

- This may result in injury due to a malfunction.

Since the water drained during a high-temperature wash or drying cycle is hot, do not touch

the water.

- This may result in burns or injury.

Do not wash, spin, or dry water-proof seats, mats, or clothing*.

- Do not wash thick, hard mats even if the washer mark is on the care label.

This may result in injury or damage to the washer, walls, ﬂoor, or clothing due to

abnormal vibrations.

* Items not to wash: Woolen bedding, rain covers, ﬁshing vests, ski pants, sleeping bags,

diaper covers, sweat suits, and bicycle, motor cycle, car covers, etc.

Do not operate the washer when detergent dispenser is removed.

- This may result in electric shock or injury due to water leakage.

Do not insert your hand into the detergent dispenser after opening it.

- This may result in injury as your hand may be caught.

safety information

SAVE THESE INSTRUCTIONS

English - 9

Do not place any non-laundry objects, such as shoes, food waste, or animals into the

washer.

- This can cause abnormal vibrations that can damage the washer, and, in the case of

pets, cause severe injury or death.

Do not press the buttons using sharp objects such as pins, knifes, ﬁngernails, etc.

- This may result in electric shock or injury.

Do not wash laundry contaminated by oils, creams, or lotions usually found in skincare

shops or massage clinics.

- This may result in the rubber seal becoming deformed and water leakage.

Do not leave metal objects (safety pins, hair pins, etc.) or bleach in the tub for long periods

of time.

- This may cause the tub to rust.

- If rust appears on the surface of the tub, apply a neutral cleansing agent to the surface

and use a sponge to clean it. Never use a metal brush.

Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry

contaminated by dry cleaning detergent.

- This may result in spontaneous combustion or ignition due to heat from the oxidation of

the oil.

Do not use hot water from water cooling/heating devices.

- This may result in problems with the washer.

Do not use natural hand-washing soap in the washer.

- If it hardens and accumulates inside the washer, it may cause problems with the

product, discoloration, rust, or bad odors.

Do not wash large laundry items such as bedding in the washing net.

- Failing to do so may result in injury due to abnormal vibrations.

- Place smaller items, such as lace socks and lingerie in the washing net.

Do not use hardened detergent.

- If it accumulates inside the washer, it may result in water leakage.

Do not wash throw rugs or doormats.

- If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may

result in error such as no draining.

CRITICAL CLEANING INSTRUCTIONS

Do not clean the appliance by spraying water directly onto it.

Do not use the strong acid cleaning agent.

Do not use benzene, thinner, or alcohol to clean the appliance.

- This may result in discoloration, deformation, damage, electric shock, or ﬁre.

Before cleaning or performing maintenance, unplug the appliance from the wall socket.

- Failing to do so may result in electric shock or ﬁre.

SAVE THESE INSTRUCTIONS

WARNING

English - 10

installing your washer

UNPACKING YOUR WASHER

Unpack your washer and inspect it for shipping damage. Make sure you have received all the items

shown below. If your washer was damaged during shipping, or you do not have all of the items, contact

1-800-SAMSUNG (1-800-726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.

Packing materials can be dangerous to children; Keep all packing material (plastic bags, polystyrene,

etc.) well out of childrens’ reach.

It’s need two people collaboration When demolition washing machine cushion bottom,the machine

forward dumping shall be strictly prohibited.

OVERVIEW OF YOUR WASHER

Parts supplied

Hose guide User manual book Plastic zip hose tie Water intake cap

Tools needed

Wrench Flat screwdriver Level

Parts not supplied

• Ifyouloseanaccessoryandwanttopurchaseareplacement,contactthe

Samsung service center (1-800-SAMSUNG (1-800-726-7864)).

• Thedesignofthepartsandaccessoriesmaydierfromthepicturesabove.

Their design is subject to change without notice for product improvement.

• Donotreuseoldhoses.Onlyusenewwatersupplyhoseswhenyouinstallthe

washing machine. Old water supply hoses can leak or burst causing ﬂooding

and property damage.

• Conrmthattherearerubberwashersinsideeachcouplingofthewater

supply hoses.

Water supply hoses

Adjustable legs

Drain Hose

Control panel

Lid

Power Cord

WARNING

CAUTION

English - 11

BASIC LOCATION REQUIREMENTS

Electrical

• 120 Volt 60 Hz 15 AMP fuse or circuit breaker

• Individual branch circuit serving only your Washer is recommended.

• Your Washer is equipped with a power cord.

NEVER USE AN EXTENSION CORD.

Grounding

ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE.

This appliance must be grounded. In the event of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a power cord having a three-prong grounding plug for use in a

properly installed and grounded outlet.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

An improperly connected equipment-grounding conductor can increase the risk of electrical

shock. Check with a qualiﬁed electrician or serviceman if you are not sure whether the

appliance is properly grounded. Do not modify the plug provided with the appliance – if it

does not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

IMPORTANT SAFETY PRECAUTIONS

• To prevent unnecessary risk of ﬁre, electrical shock or personal injury, all wiring and

grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.

70 Latest Revision and local codes and ordinances. It is the personal responsibility of the

appliance owner to provide adequate electrical service for this appliance.

NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR

HOT WATER PIPES.

Water

To correctly ﬁll your Washer in the proper amount of time, water pressure of 20 to 116psi (137 to

800kPa) is required.

Water pressure less than 20 psi may cause water valve failure, or may not allow the water valve

to shut o completely, or may extend the ﬁll time beyond what your Washer controls allow,

causing your Washer to turn o. A time limit is built into the controls to prevent ﬂooding in your

home if a hose becomes loose.

The water faucets must be within 4 feet / 122 cm of the back of your Washer to match the inlet

hoses provided with your Washer.

Accessory inlet hoses are available in various lengths up to 10 feet / 275 cm for faucets that

are further away from the back of your Washer.

To avoid the possibility of water damage:

• Have water faucets easily accessible

• Turn o faucets when the washer is not in use.

• Periodically check that there is no leakage from the water inlet hose ﬁttings.

CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.

01 installing your washer

CAUTION

WARNING

CAUTION

WARNING

English - 12

Drain facility

The recommended height of the standpipe is 39 in / 99 cm. The drain hose must be routed

through the drain hose clip to the standpipe. The standpipe must be large enough to accept the

outside diameter of the drain hose. The drain hose is attached to the washer at the factory.

Flooring

For best performance, you must install your washer on a solidly constructed ﬂoor. Wood ﬂoors

may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting

and soft tile surfaces are contributing factors to vibration which can cause your washer to move

slightly during the spin cycle.

Never install your washer on a platform or weakly supported structure.

Location considerations

Do not install your washer in areas where water may freeze, since your washer will always retain

some water in its water valve, pump, and hose areas. Frozen water can damage the belts, the

pump, hoses, and other components.

Alcove or closet installation

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm

Rear – 6 in / 152 mm

Closet Front – 2 in / 51 mm

TOP - 21 in / 533 mm

Gap between end of water valve and the wall

- Case 1. Assemble supply hose after installing : Over 3.9 in (10 cm).

- Case 2. Assemble supply hose before installing : Over 2.8 in (7cm).

If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²)

unobstructed air opening. Your washer alone does not require a speciﬁc air opening.

A. Recessed area

B. Side view - closet or conﬁned area

installing your washer

2 in.

(5.1 cm)

6 in.

(15.2 cm)

29.3 in.

(74.4 cm)

B

21 in.

(53.3 cm)

Case 1. 3.9 in. (10 cm)

Case 2. 2.8 in. (7 cm)

A

1 in.

(2.5 cm)

1 in.

(2.5 cm)

27.0 in.

(68.6 cm)

27.0 in.

(68.6 cm)

1 in.

(2.5 cm)

English - 13

Required dimensions for Installation

IMPORTANT NOTE TO INSTALLER

Please read the following instructions carefully before installing your washer.

These instructions should be retained for future reference.

We recommend you hire a professional to install this washer.

Installation Flow chart

STEP 1 Selecting a Location

Before you install the washer, make sure the location:

• Hasahard,levelsurfacewithoutcarpetingorooringthatmayobstructventilation.

• Isawayfromdirectsunlight.

• Hasadequateventilation.

• Isnotexposedtofreezingtemperatures(temperaturesunder32°For0°C).

• Isawayfromheatsourcessuchasoilorgas.

• Hasenoughspacesothatthewasherdoesn’trestonitspowercord.

27.0 in.

(68.6 cm)

43.9 in.

(111.5 cm)

39.3 in.

(99.8 cm)

29.3 in.

(74.4 cm)

29.3 in.

(74.4 cm)

43.9 in.

(111.5 cm)

58.1 in.

(147.6 cm)

Closet or Door

48 in.² *

(310 cm²)

24 in.² *

(155 cm²)

3 in.

(7.6 cm)

3 in.

(7.6 cm)

*Required spacing

Selecting

a location

Removing the

shipping bolts

(*Drum only)

Adjusting the

levelling feet

Connecting the water

and the drain

[Running a test cycle]

Run a test cycle(Rinse+Spin)

with small amount of laundary

(about 4~5 Towels)

Running

a Calibration

mode

Powering your

washing machine

Finish the

installation

Does a

Laundary machine

Vibrate?

No

Yes

Please check again before steps.

01 installing your washer

English - 14

STEP 2

Connecting the water and the drain

Connecting the water supply hose

Before installing the water supply hoses, make sure there are

rubber gaskets inside the ﬁttings at both ends of each new

water hose. Installing the water supply hoses without rubber

gaskets can cause water leakage.

When you initially install the washer, be sure to use new hoses.

Failing to do so may result in a water leakage or overﬂow and

may damage your property.

Do not connect multiple water supply hoses together to

increase the length of the supply hose. Hoses connected this

way can leak and the leakage can cause electrical shock. If a

hose is too short, replace the hose with a longer, high pressure

hose.

1. Connect the ends of the water supply hoses to the HOT and COLD faucets.

2. Tighten the ﬁttings by hand until they are snug, and then tighten them an

additional two-thirds of a turn with a wrench.

When you fasten the ﬁttings, do not fasten them too tightly or apply

tape or sealant to the faucets or water supply intakes. This can

damage the ﬁttings.

After you have connected the water supply hoses to the faucets,

ensure that they are connected correctly by pulling the water supply

hoses downwards

3. Place the unconnected ends of the hoses into a bucket and open

the faucets connected to the two water supply hoses for 10 or 15

seconds to remove any foreign substances from the hoses. Close the

faucets before continuing.

4. Connect the ends of the water supply hoses to the water supply

intake connections at the back of the washer.

The water supply hose connected to the HOT faucet must be

connected to the hot water supply intake and the water hose

connected to the COLD faucet must be connected to the COLD

water supply intake.

5. Tighten the ﬁttings by hand until they are snug, and then tighten them

an additional two-thirds of a turn with a wrench.

To ensure the correct water usage, connect both the HOT and

COLD water faucets. If either or both are not connected, an

“4E” (no ﬁll) error can occur.

If you do not want to use the HOT water supply hose, insert

the water intake cap into the HOT water supply intake hole. In

this case, you must select the Tap Cold option for the water

temperature.If you select the Tap Cold option, all the lamps for

the water temperature options are turned o.

Conﬁrm that the water supply hoses are not twisted or bent. If

the hoses are twisted or bent, the hoses can leak and cause

electric shock due to the water leakage.

6. Turn on the HOT and COLD water supplies and check all the water

supply intake connections and the faucets for water leaks.

installing your washer

Rubber Washer

Coupling

Cold Hot

CAUTION

English - 15

Connecting the drain hose

The end of the drain hose can be positioned in

three ways:

Over the edge of a wash basin

Secure the guide to the side of the basin wall

with a hook or to the tap with a piece of string to

prevent the drain hose from moving.

In a standpipe or laundry tub

The standpipe must be no shorter than 39 in (99

cm) and no longer than 96 in (245cm).

Make sure that the connection between the

drain hose and the standpipe is not airtight.

Connection the hose guide within 4 in (10cm)

from the end of the drain hose. If the drain hose is

extended more than 4 in (10cm) beyond the end of the

hose guide, mold or microorganisms could spread to the

inside of the washer.

Drain Hose can be installed until 96 in (245cm) maximum.

But drain capability can be reduced at this height. It

causes the washer to have odor, because of remained

water in the drain system.

If drain hose is installed below 39 in (99cm), water can be

drained in cycle working cause of siphon phenomenon. It

causes the washer to “4E” error.

STEP 3

Leveling your washer

See if the washer is level by checking the position of the tub:

1. Slide the washer into position.

2. Open the lid of the washer, and pour the water into the tub to

just below the pulsator level.

3. If the washer is level, the pulsator is positioned at the center of the

water as shown in the ﬁgure. If not, level your washer by turning the

front leveling feet clockwise or counterclockwise as necessary.

Turn the front leveling feet clockwise to raise the washer, and

counterclockwise to lower the washer.

01 installing your washer

Laundry tub Stand pipe

Hose

retainer

Tie

strap

39” Min

(99 cm)

96” Max

39” Min

Loosen Lock

Pulsator

Adjustable legs

(three)

1RPRUHWKDQ

LQFP

+RVH*XLGH

English - 16

STEP 4

Powering your washer

Plug the power cord into a 3-prong, well grounded 120 volt 60

Hz approved electrical outlet protected by a 15-amp fuse or

comparable circuit breaker.

Your washer is grounded through the third prong of the power

cord when plugged into a three-prong grounded electrical

outlet.

Test run

Make sure that you install your washing machine correctly by running the Rinse+Spin cycle

after the installation is complete.

STEP 5

Running a test cycle

Run a test cycle as follows to check if your washer is properly installed.

1. Load about 6 pounds of laundry into the tub.

2. Press the Power button to turn on your washer.

3. Select the Rinse+Spin cycle by turning the Cycle Selector.

4. Press the Start/Pause button to start the test cycle.

5. The washer should not rock or vibrate excessively when water is supplied or when washing

or spinning, and should drain well during the spin cycle.

If water leaks while water is being supplied or drained, check the water connections. Refer

to the “Connecting the water and the drain” section on pages 14~15 for instructions.

If the washer rocks and vibrates excessively, level your washer again. Refer to the “Leveling

your washer” section on page 15 for instructions.

STEP 6

Calibration mode

Your Samsung washing machine detects the laundry weight automatically.

For more accurate weight detection, please run Calibration Mode after the installation.

To run Calibration Mode, follow these steps:

1. Remove laundry or any contents in the machine.

2. Press the Temp. and Delay End buttons simultaneously, and then press the Power button.

The machine turns on.

3. Press the Start/Pause button to activate “Calibration Mode”.

4. The pulsator rotates clockwise and counterclockwise for approximately 1 minute.

5. When “Calibration Mode” is ﬁnished, “End” (WA48H7400A*, WA45H7200A*) / “0”

(WA45H7000A*)

appears on the display, and the machine automatically turns o. The washing machine is now

ready for use.

installing your washer

English - 17

operating instructions

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

LOADING YOUR WASHER

• You can ﬁll the tub with dry, unfolded clothes, but DO NOT OVERLOAD the tub, No more than 3/4 full.

• Overloading may reduce washing eciency, cause excess wear, and possibly cause creasing or

wrinkling of the load.

• Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar

lightweight items.

• When washing big bulky items or a few smaller items that don’t ﬁll the tub completely – a rug, a pillow,

stued toys, or one or two sweaters, for example – add a few towels to improve spin performance.

• Do not insert bulky items except for Bedding in this cycle.

During the spin cycle, the washer may add additional water to redistribute the clothes and correct an

imbalance inside the drum.

• When washing heavily soiled loads, do not overload your washer to ensure good cleaning results.

• To add a forgotten item:

1. Press the Start/Pause button to pause the washer.

2. Wait for the door to unlock automatically, and then open the door.

3. Add the item, close the door, and then press the Start/Pause button. The cycle will resume.

GETTING STARTED

1. Load your washer.

2. Add liquid (or powder) detergent and additives to the dispenser (see pages 24~26).

3. Select the appropriate cycle and options for the load (see pages 18~23).

4. Close the lid.

5. Press the Start/Pause button.

6. The Wash Indicator light illuminates.

7. The estimated cycle time will appear in the display.

The time may ﬂuctuate to indicate the time remaining in the cycle better.

The actual time required for a cycle may dier from the estimated time in the display depending on the

water pressure, water temperature, detergent, and laundry.

8. Before your washer starts to ﬁll, it will make a series of clicking noises to check the door lock and do a

quick drain.

• When the cycle is complete, the Door Lock light will go out and “End” (WA48H7400A*,

WA45H7200A*) / “0” (WA45H7000A*) will appear in the display.

• Pressing the Power button cancels the cycle and stops your washer.

•

The Wash, Rinse ,and Spin indicator lights will illuminate during those portions of the cycle.

02 operating instructions

WARNING

English - 18

washing a load of laundry

OVERVIEW OF THE CONTROL PANEL

Cycle Selector

Select the appropriate cycle for the type of load.

The cycle you select determines the tumble pattern and spin speed

for the cycle.

To minimize wrinkling of laundry, select the Perm Press cycle.

NORMAL - For most fabrics including cottons, linens, and normally

soiled garments.

HEAVY DUTY - For sturdy, colorfast fabrics and heavily soiled

garments.

COLORS/DARKS (WA48H7400A*, WA45H7200A*) - For brightly or

dark colored casual garments.

BEDDING - For bulky items such as blankets and sheets. When you

are washing comforters, use liquid detergent.

DELICATES - For sheer fabrics, bras, lingerie, silks, and other

handwash-only fabrics. For best results, use liquid detergent.

WATERPROOF - For waterproof, water-resistant items.

* Do not wash waterproof items and non-waterproof items together.

PERM PRESS - For wash-and-wear, synthetic fabrics, and lightly to

normally soiled garments.

WA48H7400A*

43 5

1 6

7

8

2

WA45H7200A*

WA45H7000A*

1

English - 19

ACTIVE WEAR (WA48H7400A*, WA45H7200A*) - Use this cycle to wash

exercise wear such as sports jerseys, training pants, shirts/tops and other

performance clothing. This cycle provides eective soil removal with gentle

action for special fabric care.

QUICK WASH - For lightly soiled garments needed quickly.

SPIN - Drains the water and spins at a high speed.

RINSE + SPIN - Use for loads that need rinsing only or to add rinse-added

fabric softener to a load.

Display

Provides instructions and diagnostics while keeping you updated on the cycle

status and time remaining.

Temp. selection

button

Press the button repeatedly to cycle through the dierent water temperature

options.

Hot - Whites and heavily soiled, colorfast items.

Warm - Colorfast items.

Eco Warm - Moderately soiled, colorfast items; most wrinkle-free items.

Cold - Brightly colored, very lightly soiled items.

Tap Cold - Cold water with no warm water added.

 If you select the Tap Cold option, all the lamps for the water

temperature options are turned o.

Spin selection

button

Press the button repeatedly to cycle through the dierent spin speed options.

High - Use for underwear, t-shirts, jeans, and sturdy cottons.

Medium - Use for jeans, wrinkle-free or wash-and-wear items, and

synthetics.

Low - Use for delicate items needing a slow spin speed.

No Spin - Drains your washer without spinning. Use for extremely delicate

items that cannot tolerate any spin.

Soil Level

selection button

Press the button to select the soil level/washing time.

Heavy - For heavily soiled loads.

Normal - For moderately soiled loads. This setting is best for most loads.

Light - For lightly soiled loads.

Select Cycle

Option

Press these buttons to select dierent cycle options.

AquaJet

TM

Deep Clean (WA48H7400A*) - Improve washing performance

through longer AquaJet spray action. Water Level can be adjusted.

AquaJet

TM

(WA45H7200A*) - Improves the washing & rinsing performance

using falling water.

Extra Rinse (WA45H7000A*) - Change from spray rinse mode to deep rinse

mode, and rinse once again.

Delay End - Delay the end of any cycle for up to 19 hours in one-hour

increments. Displayed hour indicates the time the wash will be ended.

Self Clean - Use to clean dirt and bacteria from the drum. Regular use(after

every 20 washes) is recommended. No detergent or bleach is needed.

Pre Soak - Remove stains more thoroughly by specifying additional time.

Start/Pause

selection button

Press to pause and restart cycles.

Power button

Press once to turn your washer on. Press again to turn your washer o. If

the washer is left on for more than 10 minutes without any buttons being

touched, the power automatically turns o.

7

03 washing a load of laundry

2

3

4

5

6

8

English - 20

Child Lock [ ]

Child Lock prevents children from playing with your washer.

Activating the Child Lock function

Press and hold the Spin and Soil Level buttons simultaneously for approximately 3 seconds.

• When you activate the Child Lock function, the “Child Lock [

]” lamp blinks.

Using the Child Lock function

If the lid is opened when the Child Lock function is on, “dE” is displayed and an alarm sounds.

• If the water level in the tub is above the safe water level, “dE” is displayed on the LED display

and the washing machine starts to drain water by force after 30 seconds.

• If the water level in the tub is above the safe water level and the Child Lock function is turned

on while the door is open, “CL” is displayed on the LED display even if the power of the

washing machine is turned o and the washing machine drains water by force.

• Even if the power of the washing machine is turned o, if the lid is opened while the water

level in the tub is above the Reset water level, “CL” is displayed on the LED display without

the alarm sounding and the washing machine starts to drain water. When the draining

operation ﬁnishes, the power is automatically turned o again.

• You have activated the Child Lock function while the washing machine is running, the Start/

Pause button will not work.

• After the compulsory drain, the “CL” code display blinks at 1 second intervals and the

product enters the “CL” mode. (When the product is in the “CL” mode, only the Power

button works.)

• To cancel the “CL” mode, you need to turn the power o and then on again.

• To cancel the “dE” mode, deactivate the Child Lock function. To deactivate the Child Lock

function, press and hold the Spin and Soil Level buttons simultaneously for at least

3seconds.

Adding laundry when Child Lock is on

• Toaddlaundry,deactivatetheChildLockfunction.TodeactivatetheChildLockfunction,

press and hold the Spin and Soil Level buttons simultaneously for at least 3seconds.

See “Pause Option” on page 23 for additional details.

Deactivating the Child Lock function

Press and hold both the Spin and Soil Level buttons simultaneously for approximately

3seconds.

• When you deactivate the Child Lock function, the “Child Lock [

]” is turned o.

• The Child Lock function prevents children or the inﬁrm from accidently operating the washer

and injuring themselves.

• Ifachildentersthewashingmachine,thechildmaybecometrappedandsuocate.

• OnceyouhaveactivatedtheChildLockfunction,itcontinuesworkingevenifthepower

is turned o.

• Forcingthelidopencanresultininjuryordamagetotheproduct.

To add laundry after you have activated the Child Lock function, you must ﬁrst deactivate

the Child Lock function.

CAUTION

WARNING

washing a load of laundry

La page charge ...

Samsung WA45H7000AW/A2 Le manuel du propriétaire

Ce manuel convient également à

Samsung WA45H7000AW/A2 Le manuel du propriétaire

dans d''autres langues

Documents connexes