Nikon ONE TOUCH 90S-QD Le manuel du propriétaire

Marque: Nikon

Modèle: ONE TOUCH 90S-QD

Catégorie: Caméras de cinéma

Taper: Le manuel du propriétaire

Ce manuel convient également à

Instruction Manual (Pages 2-39)

Bedienungsanleitung (Seiten 40-77)

Manuel d’ulilisation (Pages 78-115)

Manual de instrucciones (Páginas 116-153)

Getting Started

For your safety Caring for the Camera and Battery

To prevent damage to your Nikon product or injury to

yourself or to others, read the following safety precautions

in their entirety before using this equipment. Keep these

safety instructions where all those who use the product

will read them.

The consequences that could result from failure to

observe the precautions listed in this section are

indicated by the following symbols:

WARNINGS

Do not look at the sun through the viewfinder

Viewing the sun or other strong light source through the

viewfinder could cause permanent visual impairment.

Turn off immediately in the event of malfunction

Should you notice smoke or an unusual smell coming

from the equipment, remove the battery immediately,

taking care to avoid burns. Continued operation could

result in injury. After removing the battery, take the

equipment to a Nikon-authorized service center for

inspection.

Do not use in the presence of flammable gas

Do not use electronic equipment in the presence of

flammable gas, as this could result in explosion or fire.

Do not place strap around neck

Placing the camera strap around your neck could result

in strangulation. Special care should be taken to avoid

placing the strap around the neck of an infant or child.

Do not disassemble

Touching the product’s internal parts could result in

injury. In the event of a malfunction, the product should

be repaired only by a qualified technician. Should the

product break open as the result of a fall or other

accident, remove the battery and then take the product

to a Nikon-authorized service center for inspection.

This icon marks warnings, information that should be

read before using your Nikon product to prevent

possible injury.

Getting Started

Observe proper precautions when handling

batteries

Batteries may leak or explode if improperly handled.

Observe the following precautions when handling

batteries for use in this product:

• Be sure the product is off before replacing the

battery.

• Use only a 3 V CR2 lithium battery.

• When inserting the battery, do not attempt to insert

it upside down or backwards.

• Do not short or disassemble the battery.

• Do not expose the battery to flame or to excessive

heat.

• Do not immerse in or expose to water.

• Do not transport or store with metal objects such as

necklaces or hairpins.

• Immediately after use, or when the product is used

on battery power for an extended period, the battery

may become hot. Before removing the battery, turn

the camera off and allow the battery to cool.

• Discontinue use immediately should you notice any

changes in the battery, such as discoloration or

deformation.

Keep out of reach of children

Particular care should be taken to prevent infants

from putting the battery or other small parts into their

mouths.

Observe caution when operating the flash

Using the flash close to your subject’s eyes could

cause temporary visual impairment. Particular care

should be observed if photographing infants, when the

flash should be no less than one meter (39”) from the

subject.

Getting Started

Caring for the Camera and Battery

Keep dry

This product is not waterproof, and may malfunction if

immersed in water or exposed to high levels of humidity.

Rusting of the internal mechanism can cause irreparable

damage.

Keep free of salt, sand, and dust

After using your camera at the beach or seaside, wipe

off any sand or salt with a lightly dampened cloth and

then dry your camera thoroughly.

Do not touch the lens with your fingers

Use a blower brush to remove dirt and dust from the

lens. To remove fingerprints or smudges from the

lens’ surface, use a soft, clean cotton cloth or lens

tissue moistened with ethanol (alcohol) or lens

cleaner.

Handle the lens cover and all moving parts with care

Do not apply force to the lens or to the battery or lens

covers. These parts are especially susceptible to

damage.

Do not drop

The product may malfunction if subjected to strong

shocks or vibration.

Keep away from strong magnetic fields

Do not use or store this device in the vicinity of

equipment that generates strong electromagnetic

radiation or magnetic fields. Strong static charges or

the magnetic fields produced by equipment such as

radio transmitters could affect the product’s internal

circuitry.

Avoid sudden changes in temperature

Sudden changes in temperature, such as occur when

entering or leaving a heated building on a cold day,

can cause condensation inside the device. To prevent

condensation, place the device in a carrying case or a

plastic bag before exposing it to sudden changes in

temperature.

Getting Started

Batteries

• When you turn the device on, check the battery-level

displayed in the LCD panel to determine whether the

battery needs to be replaced. The battery needs to

be replaced the low battery power indicator appears

in the LCD panel.

• Ready a spare battery when taking pictures on

important occasions. Depending on your location,

you may find it difficult to purchase replacement

batteries on short notice.

• On cold days, the capacity of batteries tends to

decrease. Use a fresh battery at low temperatures.

Keep a spare battery in a warm place and exchange

the two as necessary. Once warmed, a cold battery

may recover some of its charge.

• Should the battery terminals become dirty, wipe them

off with a clean, dry cloth before use.

Storage

•To prevent mold or mildew, store the camera in a dry,

well-ventilated area. If you will not be using the

product for a long period of time, remove the battery

to prevent leakage and store the camera in a plastic

bag containing a desiccant. Do not, however, store

the camera case in a plastic bag, as this may cause

the material to deteriorate. Note that desiccant

gradually loses its capacity to absorb moisture and

should be replaced at regular intervals.

• Do not store the camera with naphtha or camphor

moth balls, close to equipment that produces strong

magnetic fields, or in areas subject to extremes of

temperature, for example near a space heater or in a

closed vehicle on a hot day.

•To prevent mold or mildew, take the camera out of

storage at least once a month. Turn the camera on

and release the shutter a few times before putting

the camera away again.

• Store the battery in a cool, dry place.

Getting Started

Thank you for purchasing the Nikon One Touch Zoom

90s/One Touch Zoom 90s QUARTZ DATE (QD) camera.

Be sure to read this manual thoroughly before use, and

keep it handy until you feel confident using the camera.

Some of the illustrations show the model with the date

function (One Touch Zoom 90s QD).

Your Nikon camera features:

• 35mm compact camera with built-in 2.4X zoom lens

from 38 to 90mm focal length range. ( p. 17)

•

Close-up photography in Macro mode for subjects as near

as at approx. 0.3 to 0.7m (1.0 to 2.3 ft.). ( p. 31)

Symbols used in this manual

Indicates items to be checked, such as requirements

and restrictions.

:Indicates notes and cautions you are requested

to follow.

:Indicates supplementary descriptions.

:Indicates pages for reference.

Accessories

The following strap is supplied with this camera.

Attaching the strap

Attach the strap as shown

in the illustration.

Optional accessory

• Camera case CS-L26

Strap

Getting Started

Table of Contents

For your safety _________________________________________ 2

Caring for the Camera and Battery __________________________ 4

Camera parts ________________________________________ 8

Body ______________________________________________ 8

LCD panel _________________________________________ 10

Indications in the viewfinder ___________________________ 10

1 Preparations

Installing a battery ______________________________________ 11

Turning the camera on ___________________________________ 12

Checking the battery power _______________________________ 12

Loading the film _______________________________________ 13

2 Basic Operations

Holding the camera properly ______________________________ 15

Operating the Shutter Release button _______________________ 16

Zooming _____________________________________________ 17

Shooting _____________________________________________ 18

Rewinding the film _____________________________________ 19

Removing the film ______________________________________ 19

3 Advanced Operations

When the main subject is not in the center of the picture ________ 20

Difficult-to-focus subjects ________________________________ 21

Flash photography ______________________________________ 22

Procedure for Flash Photography __________________________ 23

To automatically fire the flash _____________________________ 24

To cancel flash operation _________________________________ 25

To fire the flash intentionally ______________________________ 26

To photograph a person in a night view ______________________ 27

To reduce “Red-eye” effect _______________________________ 28

Shooting a distant view or landscape through a window _________ 30

Using the self-timer _____________________________________ 30

Close-up photography ___________________________________ 31

Printing the date/time on pictures

(One Touch Zoom 90s QD only) ________________________ 32

4 Additional Information

Correcting the date and time

(One Touch Zoom 90s QD only) ________________________ 33

Replacing the battery for date

(One Touch Zoom 90s QD only) ________________________ 34

Troubleshooting _______________________________________ 36

Specifications _________________________________________ 38

Getting Started

Strap slot ( p. 6)

Camera parts (Body)

Autofocus window

Auto Exposure

metering window

Flash

( pp. 22-27)

LCD panel ( p. 10)

Mid-roll Rewind button

( p. 19)

Red-eye Reduction lamp/

Self-Timer lamp

Lens

Autofocus window

Zoom buttons

( p. 17)

button

Red-eye Reduction

( pp. 28, 29)

Self-Timer ( p. 30)

Viewfinder

window

( p. 10)

Power button

( p. 12)

Macro button

(orange lamp)

( p. 31)

button

Flash mode ( pp. 22-27)

Infinity Focus mode ( p. 30)

Shutter Release button

( p. 16)

Camera back lock

release lever

( p. 13)

Getting Started

Green LED

( p. 10)

Film cartridge confirmation

window ( p. 34)

Tripod socket

SET button*

( p. 33)

SELECT button*

( p. 33)

MODE button*

( pp. 32, 33)

* One Touch Zoom 90s QD only

Date panel*

( pp. 32, 33)

Battery chamber lid

( p. 11)

Viewfinder

eyepiece

Getting Started

Indications in the viewfinder

1Parallax compensation marks ( p. 31)

For photography in Macro mode at a distance of

approx. 0.3m (1.0 ft.), and when shooting a subject at

a distance of less than 0.7m (2.3 ft.) with the Zoom in

the Telephoto setting.

2Autofocus spot marks ( p. 18)

Center the main subject to be in focus within this spot.

3Green LED

Lights when focus is achieved or when the flash is

ready to fire. It blinks while the flash is being charged.

If the subject is closer than approx. 0.7m (2.3 ft.), the green

LED does not light even when you press the Shutter Release

button halfway, and the shutter cannot be released. Note that

you may take a picture even if the camera-to-subject

distance is extremely short and out of the control range of

the camera. However, the focus may not be sharp.

LCD panel

Red-eye Reduction indicator

( pp. 28, 29)

Flash Mode indicator

( pp. 22-27)

Infinity Focus Mode indicator

( p. 30)

Low battery power

indicator

( p. 12)

Frame counter ( p. 14)

Self-Timer indicator

( pp. 28, 30)

The illustrations are fully labeled for your reference.

Getting Started

Installing a battery

Battery type

Use one CR2 type 3 V lithium battery in this camera.

Open the battery chamber lid using a

coin or equivalent.

Install a new battery.

Observe the correct polarities and insert the battery in the

direction shown in the illustration above.

Close the battery chamber lid.

Firmly press the battery chamber lid until it clicks shut.

Preparations

Turning the camera on

Press the Power button.

Once you press the Power button, the camera is turned on,

and the lens protrudes. When you press the Power button

again, the camera is turned off and the lens retracts.

Auto Power-Off function

The camera is automatically turned off if it is not operated for

more than 3 minutes. When the camera is turned off, the lens

cover closes, and all shooting modes are reset (except for

Red-eye Reduction mode).

Checking the battery power

Make sure that the Low Battery Power

indicator ( ) is not appeared on the LCD

panel.

If “ ” is not appeared, battery power is sufficient.

If “ ” is blinking, or no indicators on the LCD panel appear, the

battery is exhausted. Replace it with a new one.

Always check the battery condition before shooting.

It is recommended to carry spare batteries with you.

The batteries may be difficult to obtain in some areas.

13Preparations

Use DX-coded 35mm film with this camera.

For DX-coded film, film speed is automatically set. Film

speeds valid for automatic setting are ISO 100, 200, 400 and

800. (With other films, the film speed is automatically set to

ISO 100.)

When loading/unloading film, be sure not to open the camera

back cover in direct sunlight.

Recommended film

It is recommended to use ISO 400 film, which provides good

results in flash photography, and reasonable protection

against camera shake.

Open the camera back.

Slide the camera back lock release lever in the direction of the

arrow (1) to open the camera back (2).

Insert a film cartridge.

Loading the film

Tips on DX-coded 35mm film

DX code

Film cartridge

DX mark

DX-coded 35mm

film

Number of frames

Film speed

Preparations

Pull the film leader out to the red index

mark.

Hold the film cartridge and ensure film is properly

positioned with no slack.

Close the camera back, and check that

the film has been correctly loaded.

Once the camera back is closed, the film automatically

advances to the first frame. Until film loading is complete,

“

” blinks on the LCD panel.

When the film has been properly set, “ ” is displayed on the

LCD panel.

If the letter “ ” blinks on the LCD panel, film is not properly

loaded. Open the camera back again and reload film.

Loading the film (continued)

15Preparations

Holding the camera properly

Hold the camera firmly.

Prop your elbows against your body and hold the camera with

both hands.

When holding the camera vertically, make sure that the flash

is on top as shown.

Do not block the lens, autofocus window, or flash with your

fingers or hair, or the strap.

Take some trial shots

Before taking important pictures, it is strongly

recommended to take a few trial shots first to familiarize

yourself with the camera and all its features.

Nikon cannot be held responsible for malfunctions

caused by using the One Touch Zoom 90s / One Touch

Zoom 90s QD in ways not specified in this manual.

Basic Operations

16 Basic Operations

Operating the Shutter Release button

Lightly press the button halfway and

confirm the green LED lights up.

When you press the button lightly, the focus and exposure are

achieved, and the green LED lights up.

The focus is locked (Focus lock p. 20) while the Shutter

Release button is depressed lightly.

Fully depress the Shutter Release button

to take the picture.

Pressing the Shutter Release button abruptly in one stroke

may result in camera shake. Be sure to slowly press the

Shutter Release button.

While the green LED is blinking with the Shutter Release

button pressed lightly, the flash is being charged, and the

shutter cannot be released. Lightly press the Shutter Release

button again, if the green LED is not blinking and remains lit

release the shutter.

If the subject is closer than approx. 0.7m (2.3 ft.) in the

telephoto setting, the green LED does not light even when you

press the Shutter Release button halfway, and the shutter

cannot be released. Move away from the subject until the

green LED lights up. Note that the Shutter Release button may

still work even if the camera-to-subject distance is extremely

short, i.e., out of the control range of the camera.

Basic Operations

Zooming

Press the Zoom button to compose the

picture.

Press the zoom button for telephoto (90mm) photography

or the

zoom button for wide-angle (38mm) photography.

Remove your finger from the button when the desired image

size is obtained.

Example of a telephoto photograph

Example of a wide-angle photograph

18 Basic Operations

Shooting

Center the autofocus spot mark on the

main subject.

If the main subject is outside the autofocus

spot:

If the main subject is outside the autofocus spot, use the

focus lock to achieve focus. (

p. 20)

Lightly press the Shutter Release button

halfway.

Slowly press the Shutter Release button

all the way.

If the subject is dark in Auto Flash mode, the flash fires

automatically.

Pressing the Shutter Release button abruptly in one stroke

may result in camera shake.

Basic Operations

Rewinding the film

Film rewinds automatically.

At the end of the film roll, the film rewinding starts automatically.

While the film is rewinding, the number on the frame counter

decreases one by one. When rewinding is complete, the letter “

”

blinks for approx. 10 seconds, then stops blinking and remains lit.

If rewinding stops midway through the roll because of a dead

battery, it resumes automatically as soon as the battery is replaced

and the camera is turned on.

Do not open the camera back until the letter “ ” starts blinking.

To rewind the film in mid-roll

Press the mid-roll rewind ( ) button using

the point of a ballpoint pen or equivalent.

Once rewinding starts, there is no need to keep the button

pressed.

Removing the film

Make sure rewind is complete by

checking the letter “ ” indication.

Open the camera back and remove the film.

Advanced Operations20

When the main subject is not in the center of the picture

Focus lock photography

When the subject to be focused is outside the autofocus

spot in the center of the picture, use focus lock, which

enables you to change the picture composition while

locking the focus. Also use focus lock for difficult-to-

focus subjects described on the next page ( p. 21).

Compose the picture.

If the shutter is released in a condition like that in the above

example where the main subject is out of focus.

Center the autofocus spot mark on the

main subject, then lightly press the

Shutter Release button halfway.

Do not change the camera-to-subject distance

While you lightly press the Shutter Release button, the focus

is locked. Do not change the camera-to-subject distance.

While depressing the Shutter Release button

lightly, recompose the picture and depress

the Shutter Release button all the way.

La page charge ...

Nikon ONE TOUCH 90S-QD Le manuel du propriétaire

Marque: Nikon

Modèle: ONE TOUCH 90S-QD

Catégorie: Caméras de cinéma

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Nikon ONE TOUCH 90S-QD Owner's manual
Deutsch: Nikon ONE TOUCH 90S-QD Bedienungsanleitung

Nikon ONE TOUCH 90S-QD Le manuel du propriétaire

Ce manuel convient également à

Nikon ONE TOUCH 90S-QD Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents