NewAge Products 12031 Mode d'emploi

IM-FL2.002A-02

NewAge Stone Composite

Interior Flooring

Installation Guide

STOP

ATTENTION: Is your ooring damaged?

Need help or spare parts? For fastest service,

contact NewAge Products at 1-877-306-8930;

or support@newageproducts.com.

Do not return to the retailer.

2

Index

General Information - 3

Product Specications - 3

Available Interior Accessories - 4

Tools Needed - 5

Precautions - 6

Acclimation - 6

Expansion gap - 6

Recommended Blades - 6

Recommended Cutting Methods - 7

General Suboor Preparation - 8

Concrete suboors - 8

Wood suboors - 9

Radiant heating - 9

Baseboard and Quarter Round Preparation - 10

Installation Tips -11

Getting Started - 12

Flooring installation layout - 12

Installation Options - 13

Installing the Flooring (Tiles / Planks) - 14

Installing T- Molding Transition Strips - 18

Installing Multi-Purpose Reducers - 20

Care and Maintenance - 22

Warranty - 23

3

General Information

Product Specications

• NewAge Stone Composite Luxury Vinyl oors have been designed to withstand busy

households and commercial spaces.

• NewAge Stone Composite Luxury Vinyl oors are heavy and needs to be lifted with care.

Please use proper lifting techniques when handling the products.

• For best results, mix and install planks/tiles from dierent cartons to achieve desirable

variation.

• NewAge oors has been designed to be an easy drop and lock system.

Stone Composite Luxury Vinyl Plank

• Single Floor Plank:

L 46in x W 8.85in x 9.5mm thickness

• x5 Floor Planks in a Carton

• 14.15 SQFT Per Carton

Stone Composite Luxury Vinyl Tile

• Single Floor Plank:

L 23in x W 12in x 9.5mm thickness

• x7 Floor Tiles in a Carton

• 13.44 SQFT Per Carton

4

Available Interior Accessories

• T-Molding Transition Strips easily

connects any two oor surfaces of the

same height.

• This accessory is only available in

matching colours for the wood planks

and not stone tiles.

• Product Dimension:

L 46in X W 1.65in X H 0.5in

• 1 T-Molding and 1 Connection Base per

kit

Multi- Purpose Reducer and Connection

Base

T-Molding Transition Strip and

Connection Base

• The Multi-Purpose reducer creates a

smooth transition between two oors

with dierent heights.

• This accessory only available ion

matching colours for the wood planks

and not stone tiles.

• Product Dimension:

L 46in x W 2.17in x H 0.5in

• 1 Multi-Purpose Reducer and 1

Connection Base per kit

5

Tools Needed

Ruler

Laser level

Vacuum / Broom

Interior/ Exterior Commercial

grade Silicone Sealant

PencilTape Measure

Safety Glasses

Knee PadsFace Mask

Chisel

Spacers, tapping block

and pulling Iron

LevelerUtility Knife

Rubber Mallet

Multi Tool Cutter

Hammer

Compound Miter Saw

Ruler

Laser level

Vacuum / Broom

Interior/ Exterior Commercial

grade Silicone Sealant

PencilTape Measure

Safety Glasses

Knee PadsFace Mask

Chisel

Spacers, tapping block

and pulling Iron

LevelerUtility Knife

Rubber Mallet

Multi Tool Cutter

Hammer

Compound Miter Saw

Recommended Tools

Alternative Tools

6

• Although acclimation is not required, for best results ooring could be acclimated for 24-48

hours in its desired environment before opening the cartons.

• It is recommended to install the oors when the room temperature is at least 5°C (41°F) to

24°C (75.2°F).

Acclimation

Expansion gap

Precautions

• Do not store Floor Tile and Plank boxes on their sides. Store all boxes horizontally at on the

oor.

• Do not use heavy duty tools designed for other ooring materials or installation systems.

• NewAge luxury vinyl oor tiles and planks are nished products. Do not use any ooring

nishes (wax/polish).

• NewAge luxury vinyl tiles and planks are designed for the oating installation method only.

Do not glue down or secure the oor tiles and planks directly to the oor.

• Before starting installation, ensure all cartons contain the correct product.

• It is recommended to install your oors in bright daylight to observe any possible

imperfections, defects or damages. NewAge will not be held responsible for any costs related

to installation or visual defects post installation.

• NewAge Flooring : 100 Tooth Carbide Tipped Thin Kerf Blade

• NewAge T-Molding / Multi-purpose Reducers : 100 Tooth Carbide Tipped Thin Kerf Blade

• NewAge 46” Silver Finishing Strips : 100 Tooth carbide tipped Aluminum Saw Blade

• NewAge Flooring : High Carbon Steel End Cut Blades

• NewAge T-Molding / Multi-purpose Reducers : High Carbon Steel End Cut Blades

• NewAge 46” Silver Finishing Strip: A Semi Circular Bi Metal Saw Blade

Recommended Blades

Compound Miter Saw

Multi-Tool Cutter

• Carefully follow instructions on page 13 “Installation Options”.

7

• Tip: When using a Multi-Tool cutter on your NewAge Floor Tiles, Planks and Accessories, it

is recommended to use a slower cutting speed until you are comfortable to cut faster. This

would allow you to gain more control and avoid any errors.

Warning: Be sure to wear a face mask and safety glasses to protect yourself from the dust while

cutting the oor tiles, planks and accessories.

Recommended Cutting Methods

For large simple and straight cuts , use a compound miter saw.

For smaller and complicated cuts, use a multi-tool cutter.

1

2

8

General Suboor Preparation

Preparing your space - General

• Correctly preparing your suboors plays a large part of a satisfactory installation. The NewAge

Stone Composite Flooring uses a “oating oor” installation method which can handle minor

oor imperfections. If you have large gaps or protrusions in your suboors, NewAge Stone

Composite Flooring will not be able to cover them.

• It is not suitable to install NewAge ooring on carpet. All carpet and carpet track’s should be

removed before installation.

• Prior to installing your oors, use a vacuum to remove all dust and debris.

• Ensure the surface is structurally sound, at, clean and dry before installing NewAge Flooring.

If your oors are wet, make sure you wait until they are fully dry before proceeding with the

install.

• Leave at least a 0.5” gap between the surface of the oor and the bottom of an electric

baseboard heater to allow heat to circulate.

• Suboor atness should not exceed 3/16” per 10ft (4.7mm per 3m radius). Suboors must be

leveled before starting the installation of the NewAge Stone Composite Tiles and Planks.

• Chisel any uneven surfaces on the oor before starting the ooring install.

• Make sure all surfaces are dry, clean and free of dust, wax, solvents, paint, grease, oils and old

glue residue.

• Sand or grind any raised areas.

• Gaps and holes should be lled with concrete and nished with a straight edge to even the

oor out.

• It is important to test the moisture level before starting the install. Using a concrete moisture

meter, the moisture vapor emission rate should not exceed 5lbs per 1000sqft in 24hr. If In Situ

probe testing is to be carried out, according to ASTM F2170, it should not exceed 85%. These

tests would not predict the condition of your oors for long-term and would only indicate the

condition of your oors at the time of the test being conducted.

Note: If you have done concrete work in the desired space, sub-oors must properly cure and be

left to dry for at least 60 days before installing NewAge Stone Composite Flooring.

Concrete suboors

9

• NewAge Stone Composite Flooring is suitable to be installed over radiant heating systems as

long as the heating element is not in direct contact with the ooring. Leave at least 1/2” gap

between the Floors and radiant heat systems.

• If the radiant heating has been newly installed, leave the system on and operational for at

least 2 weeks prior to installation. This would reduce the moisture levels in the concrete.

• Turn o the heating system for 24 hrs before and after installing NewAge Stone Composite

Flooring.

• It is recommended for the desired room to be 5°C (41°F) to 24°C (75.2°F) prior to installation.

You may need to use other heating methods prior to install.

Radiant heating

General Suboor Preparation

• Test the moisture content of wood suboor using a moisture meter. It should not exceed

12%.

• Sand or plane high spots and ll all holes and gaps.

Wood suboors

• Suspended wood suboors should have at least 18 inches of well-ventilated crawl space

underneath.

• NewAge Stone Composite Flooring can be installed over many wood substrates as long as

the surface is smooth, at and structurally sound.

• Repair any squeaky oors before installing NewAge Stone Luxury Flooring.

Note: Due to the use of power and manual tools during installation, damage may occur to the

wood suboors.

10

• If there are pre-installed baseboards in need of replacement, remove old baseboards and

quarter rounds.

• If new baseboards and quarter rounds need to be installed, install these items after the oors

have been completed.

• Chisel any uneven surfaces on the oor and wall before starting the install.

• Ensure the general space preparation has been completed before starting install. Reference

page 8.

• Ensure Concrete suboor, Radiant heating or wood suboor requirements has been followed.

Reference page 8-9.

• NewAge Stone Composite ooring can not be installed with pre-installed quarter rounds. All

Quarter rounds need to be removed before starting install.

• Once all quarter rounds have been removed, cut approximately 11mm o the bottom of your

baseboards to have enough space for the 9.5mm oor planks or tiles.

• Note: If previous oors are thicker than the new Luxury Vinyl Floors, you may need to

purchase a new door casing or plinth block.

• Quarter rounds will need to be installed after the ooring is complete.

• Ensure the general space preparation has been completed before starting install. Reference

page 8.

• Ensure Concrete suboor, Radiant heating or Wood Suboor requirements has been followed.

Reference page 8-9.

Option 1: Installing Interior ooring before baseboards and quarter rounds.

Option 2: Installing Interior ooring with pre-installed baseboards and

quarter rounds.

Baseboard and Quarter Round Preparation

11

Installation Tips

TIP - 1 : To make installation easier and quicker, equally distance your boxes of planks or tiles

on your oors. This would allow you to better plan your install.

TIP - 2 : Cut a piece of tile/plank and use it as a tapping block.

TIP - 3: When installing ooring around door trims and it is challenging to use the click lock

proles, remove the top section of the click lock prole to allow you to slide in the plank or

tile under the installed oor. Apply the recommended silicone , on page 5, along the click

lock prole and slide it under the installed ooring. Make sure to wipe o any excess glue and

ensure glue used will dry in clear colour.

12

Getting Started

Flooring installation layout

• It is recommended to lay the long side of the Planks or Tiles parallel to the longest wall or

main window of the room.

• When installing the oors, stagger the tiles/planks to ensure a secure installation .

• To determine the number of rows of tile/planks are required, measure the width of the room

and width of the planks or tiles.

• Divide the width of the room by the width of the planks / tiles to get the number of rows

required.

• If the last row is less than the width of a full tile or plank, cut the rst row accordingly such

that the rst row and last rows are of even widths.

L

W

13

• Ensure you have followed the recommended steps on page 10.

• Once your space has been prepared and all quarter rounds have been removed , line your tile

or plank along the edge of your baseboard.

• This will need to remain the same along the perimeter of the room.

• Quarter rounds will be installed once oors have been completed.

Option 2 : Installing NewAge Interior Flooring with pre-installed

baseboards and quarter rounds.

Installation Options

Option 1 : Installing NewAge Interior ooring before installing baseboards

and quarter rounds.

• Ensure you have followed the recommended steps on page 10.

• Once your space has been prepared , measure 3/8” from your wall and rst tile / plank. The

3/8” gap will need to remain as your expansion gap along the perimeter of the room.

• Baseboards and quarter rounds will be installed once the oors have been completed.

3/8”

14

Installing the Flooring (Tiles / Planks)

a

b

c

d

Make sure the open click lock proles of

the rst tile is at the bottom and right

hand side away from the walls.

Place the second tile, on a slight angle,

against the rst oor tile. Slide the tile to

position.

2 3

c

d

a

b

Parts required

Note: Installation layout for the Stone Tiles and Wood planks are the same.

If installing Transition Strips and Multipurpose Reducers, refer to page 18 before starting the install.

Stone Composite

Luxury Vinyl Tiles

Tape Measure

Interior / Exterior

Commercial grade

Silicone sealant

Stone Composite

Luxury Vinyl Planks

Or

Rubber Mallet

1

Make sure you have followed the recommended space preparation and read through the

dierent Install Options on page 12-13. Ensure you have measured the correct expansion gap.

15

Using a rubber mallet, tap along the drop

click prole with medium force to secure a

tight seam.

Place the tapping block along the open

click prole of the short edge and tap over

it with a rubber mallet. This ensures a tight

install.

4

5

Installing the Flooring (Tiles / Planks)

Make sure the edges are aligned perfectly.

Place the tapping block on the open click

prole of the long edge and tap over it

with a rubber mallet to align the tiles.

Follow steps 1 to 7 for remaining row of

tiles. Measure the space left for the last tile

using a tape measure.

76

8 9

Cut the tile to required length. Refer to

the page 7 for “Recommended Cutting

Method “. Note: Ensure there is proper

clearance from the wall based on your

preferred installation.

16

f

e

g

Installing the Flooring (Tiles / Planks)

f

e

Place your tile on an angle along the long

edge of the rst row and drop the tile

down. Repeat steps 4 - 7 for each tile.

Place your second tile on an angle along

the long edge of the rst row and drop the

tile down. Note: Make sure your tiles are

cliped into each other properly along the

long and short edge.

12

e

ef

f

11

Note: When starting the second row, cut the rst tile in half or use the leftover from the rst row.

Install the last tile of the rst row.

10

f

f g

g

17

Note: When starting the second row, cut the rst tile in half or use the leftover from the rst row.

13

Installing the Flooring (Tiles / Planks)

Follow steps 1 to 12 for remaining row of tiles.

Note: Once all oors have been installed, baseboards and quarter rounds may now be

installed to complete your space.

18

Compound Miter Saw

T-Molding Transition Strip

Connection Base

Interior/ Exterior Commercial

grade Silicone Sealant

9.5mm Floor

9.5mm NewAge

Flooring

Parts required

Cut the T-molding transition strip and

connection base to required length using

a compound miter saw.

Stick the connection base to the oor

adjacent to the adjoining ooring. Make

sure the wide edge of the connection base

is facing towards the ooring that is to be

laid.

Evenly apply silicone to the back side of

the connection base.

1

3

2

Installing T- Molding Transition Strip

19

Lay the last row of tiles on the wide edge of connection base. This would would connect two

adjoining oors of the same height.

Snap the T-Molding into the base, pushing it all the way down until the strip is in place. Make

sure both edges of the molding is pushed all the way to the oor.

5

4

Installing T- Molding Transition Strip

Note: Wipe o the excessive adhesive at the corners with a clean cloth.

20

Multi-Purpose Reducer

Connection Base

Interior/ Exterior Commercial

grade Silicone Sealant

Compound Miter Saw

9.5mm NewAge

Flooring

Floor

Parts required

Cut the Multi-Purpose reducer and

connection base to required length using

a compound miter saw.

Stick the connection base to the

oor. Make sure the wide edge of the

connection base is facing towards the

ooring that is to be laid.

Evenly apply silicone to the back side of

the connection base.

1

3

2

Installing Multi-Purpose Reducer

La page charge ...

NewAge Products 12031 Mode d'emploi

NewAge Products 12031 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents