Shindaiwa MTA-AHS-HD Manuel utilisateur

Catégorie
Taille-haies électriques
Taper
Manuel utilisateur
1????
OPERATOR'S MANUAL
MANUEL D'UTILISATION
BEDIENUNGSANLEITUNG
MANUALE PER L'OPERATORE
MANUAL DE INSTRUCCIONES
MTA-AHS-HD
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR
SAFE OPERATION. FAILURE TO DO SO COULD RESULT IN SERIOUS IN-
JURY.
AVERTISSEMENT
LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LESRÈGLES DE
SECURITÉ.LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN
ISQUE DE BLESSURE GRAVE.
WARNUNG
LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE
FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS
RISIKO SCHWERER VERLETZUNGEN.
AVVERTENZA
LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE
IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA
DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.
ADVERTENCIA
LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES
PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SU-
FRIR LESIONES GRAVES.
1Cover
OPERATOR'S MANUAL
HEDGE TRIMMER ATTACHMENT
MTA-AHS-HD
ENGLISH
(Original instructions)
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE
RULES FOR SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
2
Important information
2Important informati on
Please ensure that you read the operator's manual before using your product.
Introduction
This product was designed and manufactured to provide long life and on-the-job dependability.Read and understand
this manual you found in the package. You will find it easy to use and full of helpful operating tips and SAFETY mes-
sages.
Users of the product
You should not use this product until you have read the operator's manual carefully and fully absorbed its content.
This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a
cold, tiredness or otherwise in poor physical condition, or children.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-
erty.
About your operator's manual
This manual contains necessary information about the assembly, operation, and maintenance of your product. Please
read it carefully and absorb its contents.
Always keep your manual in a place where it is readily accessible.
If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.
The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,
and there may be a slight conversion error in some cases.
Loaning or assigning your product
When loaning the product described in this manual to another party, ensure that the person borrowing and working with
the product receives the operator's manual along with the product. If you assign your product to another party, please
enclose the operator's manual with the product when handing it over.
Enquiries
Please contact your dealer for requests regarding information about your product, the purchase of consumables, re-
pairs, and other such enquiries.
Notices
The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the
illustrations used may differ from the product itself in order to make the explanations clearer.
This product requires the assembly of some parts.
Please consult your dealer if anything is unclear or of concern.
IMPORTANT
This attachment is designed for use with the PAS-2620ES and M262S power sources. Use of this attachment with any
other product will cause premature gear case failure and void the warranty.
WARNING
Read rules for safe operation and instructions carefully. YAMABIKO provides Operator's Manuals with your original
PAS-2620ES and M262S. That manual and this manual must be read and understood for proper and safe operation, oth-
erwise serious personal injury may result.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a re-
placement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
For warranty service, find the nearest Authorised Service Dealer in our dealer locator map at www.echo australia.com.au/
en_au/finder, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au ,Briggs &
Stratton Australia Pty Ltd, Locked bag 5004, St Clair, NSW 2759.
3
Contents
For safe use of your product............................................................................................... 4
Warning notices............................................................................................................. 4
Other indicators ............................................................................................................. 4
Symbols.........................................................................................................................4
Location in which a safety decal is attached.................................................................. 5
Handling the product ..................................................................................................... 5
Description.......................................................................................................................... 9
Before you start ................................................................................................................10
Packing list .................................................................................................................. 10
Assembly ..................................................................................................................... 10
Adjusting cutting angle ................................................................................................ 11
Operation .......................................................................................................................... 13
Maintenance and care ...................................................................................................... 14
Maintenance and care ................................................................................................. 14
Storage ............................................................................................................................. 16
Specifications.................................................................................................................... 17
Declaration of conformity .................................................................................................. 18
UK Declaration of conformity ............................................................................................ 19
4
For safe use of your product
For safe use of yo ur product
Be careful to read this section before using your product.
The precautions described in this section contain important safety information. Please observe them carefully.
You must also read the precautions that appear in the body of the manual itself.
Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.
Warning notices
Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product
itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.
Other indicators
As well as warning notices, this manual uses the following explanatory symbols:
Symbols
In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what
each symbol means.
DANGER WARNING CAUTION
This symbol accompanied by the
word "DANGER" calls attentions to
an act or a condition which will lead to
serious personal injury or death of op-
erators and bystanders.
This symbol accompanied by the
word "WARNING" calls attentions to
an act or a condition which can lead to
serious personal injury or death of op-
erators and bystanders.
"CAUTION" indicates a potentially
hazardous situation which, if not
avoided, may result in minor or mod-
erate injury.
Circle and slash sym-
bol means whatever is
shown is prohibited.
NOTE IMPORTANT
This enclosed message provides tips
for use, care and maintenance of the
product.
Framed text featuring the word "IM-
PORTANT" contains important infor-
mation about the use, checking,
maintenance and storage of the prod-
uct described in this manual.
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
Carefully read the operator's
manual Keep bystanders away 15 m
Wear eyes, ears and head
protection
Beware of high-temperature
areas
Wear foot protection and
gloves
Do not operate closer than 15
M from electrical hazards.
Emergency stop Beware of electric shocks
5
For safe use of your product
Location in which a safety decal is attached
The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what
the decal means before using your product.
If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal
from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.
Handling the product
General precautions
1. Safety decal (Part number 890617-21661)
WARNING
Operator's manual
Be careful to read the operator's manual properly before using your product in order to ensure correct
operation.
Failure to do so could lead to an accident or serious injury.
Do not use the product for anything other than its intended purpose
You must not use the product for any purpose other than those described in the operator's manual.
To do so could lead to an accident or serious injury.
Do not modify the product
You must not modify the product.
To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be
covered by the manufacturer's warranty.
Do not use the product unless it has been checked and maintained
You must not use the product unless it has been checked and maintained. Always ensure that the product is checked
and maintained on a regular basis.
Failure to do so could lead to an accident or serious injury.
Loaning or assigning your product
When loaning your product to another party, ensure that the person borrowing the product receives the operator's
manual along with it.
If you assign your product to another party, please enclose the operator's manual with the product when handing it
over.
Failure to do so could lead to an accident or serious injury.
6
For safe use of your product
Precautions for use
Being prepared in case of an injury
In the unlikely event of an accident or injury, please ensure that you are pre-
pared.
First aid kit
Towels and wipes (to stop any bleeding)
Whistle or mobile phone (for calling outside help)
If you are unable to perform first aid or call for outside help, the injury could
worsen.
WARNING
WARNING
The area within a 15 m radius is a danger zone
The area within a 15 m radius of the product is a danger zone. Be careful to
observe the following precautions while working with the product.
Do not allow children and other people or pets to enter the danger zone.
If another person enters the danger zone, turn off the engine unit to stop the
blade
When approaching the operator, signal to him by, for example, throwing
twigs from outside the danger zone, and then check that engine has been
switched off and the blade has stopped moving.
Do not allow anyone to hold the material you are cutting.
Any contact with the cutter blade could cause serious injury.
Avoid hot surfaces
During operation, the complete unit, especially the drive shaft housing, power head, muffler and gear box
may become very hot, too hot to touch. Avoid contact during and immediately after operation.
You could burn yourself if you touch a high temperature component.
WARNING
Users of the product
The product should not be used by:
people who are tired
people who have taken alcohol
people who are on medication
people who are pregnant
people who are in poor physical condition
people who have not read the operator's manual
children
Failure to observe these instructions could lead to an accident.
Environment of use and operation
Do not use the product in places where there is no sure foothold, such as on steep slopes or after rainfall, as such
places are slippery and dangerous.
Do not operate the product at night or in dark places with poor visibility.
Do not work in odd positions or on ladders. Do not over reach.
A serious injury could result if you fall or slip, or fail to operate the product correctly.
For your own health and your safe and comfortable work, operate the machine within the air temperature range of -
5 oC to 40 oC.
Failure to observe these instructions could result in damage to your health.
7
For safe use of your product
Turn off the engine when moving around
When moving around in the situations described below, turn off the engine.
Moving to the place where you are working
Moving to another area while you are working
Leaving the place where you have been working
Failure to observe these precautions could cause burns or serious injury.
When transporting the product by car, empty the fuel tank, and secure the product firmly in place to prevent it from
moving around.
Travelling by car with fuel in the tank could lead to a fire.
Keep a firm grip
Hold the front and rear handles with both hands with thumbs and fingers tightly encircling the
handles.
Failure to observe these instructions could lead to an accident.
Vibration and cold
It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning, fol-
lowed by loss of colour and numbness in the fingers.
The following precautions are strongly recommended because the minimum exposure which might trigger the ailment
is unknown.
Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.
Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not
smoking.
Limit the number of hours of operation.
Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required.
If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, consult
your physician before exposing yourself further to cold and vibration.
Failure to observe these instructions could result in damage to your health.
Repetitive stress injuries
It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,
swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities may put
you at a high risk for developing a repetitive stress injury (RSI).
To reduce the risk of RSI, do the following:
Avoid using your wrist in a bent, extended or twisted position.
Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the
repetitive movement.
Do exercises to strengthen hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-
nosed, the more likely permanent nerve and muscle damage can be prevented.
Failure to observe these instructions could result in damage to your health.
Proper training
Do not permit operation without proper training and protective equipment.
Be thoroughly familiar with the controls and proper use of unit.
Know how to stop the unit and shut off the engine.
Never allow anyone to use the unit without proper instruction.
WARNING
8
For safe use of your product
Protective gear
WARNING
Wear protective gear
Always wear the following protective gear.
a Head protection (helmet): Protects the head
b Ear muffs or ear plugs: Protect the hearing
c Safety goggles: Protect the eyes
d Face shield: Protects the face
e Safety gloves: Protect the hands from cold and vibration
f Work clothes that fit (long sleeves, long trousers): Protect the body
g Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes
(with toecaps): Protect the feet
h Shin guards: Protect the legs
Failure to observe these precautions could result in damage to your sight or hear-
ing, or lead to a serious injury.
When necessary, please use the protective gear below.
Dust mask: Protects the breathing apparatus
Bee net: To deal with attacks by bees
Wear proper clothing.
Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the unit.
Do not wear open toed footwear, or go bare-foot or barelegged. In certain situations, to-
tal face and head protection may be required.
Failure to observe these precautions could result in damage to your sight or hearing, or lead
to a serious injury.
9
Description
Description
1. Outer tube Part of the unit that provides a casing for
power transmission shaft.
2. Cutter assembly adjustment lever Provides secure
hand grip for adjusting cutting blade angle.
3. Latch lock Fixes the angle of the cutter.
4. Latch release Safety device to prevent the latch lock
from being released unexpectedly.
5. Gear housing assembly Gear housing contains drive
gears for transmitting power to cutting blades.
6. Cutter bar and cutter blades That part of the assembly
of cutter blade and shear plate together with any sup-
porting part, which performs the cutting action.
7. Blunt extension An extending blunt part of the cutting
device.
8. Blade cover When transporting or storing the product
always fit the blade cover.
9. Type and serial number
10
Before you start
Before you start
Packing list
Assembly
Power head shaft/lower shaft assembly
1. Set power head/shaft assembly on a level surface.
2. Pull locator pin (A) out, and turn anticlockwise 1/4 turn to
lockout position.
3. Remove vinyl cap from attachment drive shaft.
4. Carefully fit attachment drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower
drive shaft engages into the square upper drive shaft socket.
5. Rotate locator pin (A) 1/4 turn clockwise to engage lower
shaft hole. Insure locator pin is fully engaged by twisting low-
er drive shaft. Locator pin should snap flush in coupler. Full
engagement will prevent further shaft rotation.
6. Secure lower shaft assembly to coupler by tightening clamp-
ing knob (D).
The following parts are packed separately in the packing box.
When you have unpacked the box, please check the parts that it contains.
Contact your dealer if anything is missing or broken.
1. Operation shaft
2. Blade cover
3. L-wrench
4. Spanner
5. Storage hook assembly
6. Operator's manual
WARNING
Read the operator's manual carefully to ensure that you assemble the product correctly.
Using a product that has been incorrectly assembled could lead to an accident or serious injury.
NOTE
Lower bearing housing and head assembly must be in line with
the power source.
11
Before you start
7. To disassemble, reverse assembly instructions.
Adjusting cutting angle
Adjusting the hedge trimmer cutter assembly
1. Position the hedge trimmer on a flat, level surface with the
engine resting on the fuel tank guard. Make sure the blade
cover is in place on the blade.
2. With your right hand, grasp the outer tube near the handle.
With your left hand, grip the adjustment lever (A) on the cut-
ter assembly. With the index finger of your left hand, press
the latch release (B). With your left thumb, press the latch
lock.
3. While holding the latch release down, pivot the cutter assem-
bly using the adjustment lever until it is at the desired cutting
angle.
4. Release the latch lock (C) and the latch release. Make sure
the latch lock and the latch release return securely to the
straight ahead position.
5. Remove the blade cover (D) from the cutter blade. The en-
gine now may be started.
DANGER
Never adjust cutting assembly with engine running.
Failure to do so could lead to an injury or serious accident.
WARNING
Hedge trimmer blades are sharp. Always wear gloves when adjusting cutting assembly.
Wear heavy duty gloves when working with the hedge trimmer blades. When replacing the hedge trimmer blades
during a trimming task, ensure that the engine is switched off and that the blades have stopped.
Do not stand hedge trimmer on end when adjusting cutting angle, otherwise serious injury may result.
Gear case assembly becomes HOT during use. Always grip assembly at blade-adjustment handle when making cut-
ting angle adjustments, otherwise serious injury may result.
Failure to do so could lead to an injury or serious accident.
IMPORTANT
The latch release provides an interlock to help prevent inad-
vertent depression of the latch lock.
CAUTION
When installing and removing the blade cover from the
cutter blade, hold the handle under the blade cover.
Failure to observe these precautions could lead to injury.
12
Before you start
Cutter assembly position
The cutter assembly can be adjusted to ten different positions
ranging from 135° to 270° from the outer tube as shown. Al-
ways make sure the lock latch is securely locked after each
adjustment.
Shoulder strap
1. Hook the strap hook to the hanger on the outer tube.
2. Wear the shoulder strap so that the hook stays at your right
hand side.
3. Adjust the length of the shoulder strap so that you can hold
and operate the machine comfortably.
The shoulder harness is fitted with an emergency release
function. In case of emergency, pull up on the collar (A) to dis-
connect the machine from the strap.
IMPORTANT
Make sure all hooks and adjustment devices are secure.
13
Operation
Operation
Hedge trimming
1. Hold trimmer firmly and squeeze throttle trigger to accelerate
engine.
2. Tilt trimmer so cutting teeth are angled slightly toward the
hedge or shrub and proceed to cut.
NOTE
This product is designed to cut shrubs and hedges with branches no larger than 6 mm in diameter.
When starting to trim, run the engine at full throttle. Cutting at less at than full speed can damage the clutch by allowing it to
slip. When you do not conduct trimming or cutting work, do not run the engine at full throttle.
Before operation a complete check of the unit must be performed;
Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
Never adjust blades when the engine is operating.
Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades should not
be used.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.
Always stop engine, disconnect the spark plug wire, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
Do not start or operate unit unless all guards and protective covers are properly assembled to unit.
Never reach into any opening while the engine is running. Moving parts may not be visible through openings.
Never remove hands from unit when blades are moving.
The engine continues running even when the blades have stopped due to an obstruction. If this occurs, stop the en-
gine, disconnect the spark plug wire and remove the obstruction.
14
Maintenance and care
Maintenance and care
Maintenance and care
15/20-Hour Maintenance
Gear case lubrication
1. Clean dirt from grease fitting (A).
2. Lubricate the cutter assembly gearbox by pumping one or
two strokes of lithium-base grease into the grease fitting us-
ing a lever-type grease gun.
Drive shaft lubrication
1. Loosen the gear case clamp bolt (A).
2. Remove the index bolt (B) from gear case (C).
3. Remove the outer tube (D) from the gear housing.
4. Pull the drive shaft (E) from the outer tube, and wipe clean.
Re-coat with a thin coating 10 to 20 g, of lithium base grease.
5. Slide the drive shaft back into the outer tube, being careful
not to get dirt on the drive shaft.
6. Align the screw hole in gear case with the locating hole in
outer tube, install and tighten index bolt, and tighten gear
case clamp bolt.
Care for cutting blades
Lubricating blades (Every 4 hours of operation)
Apply a few drops of oil the each bolt slots (A) at the bottom of
blades.
Cleaning blades (After each use)
Remove gummy residue from blades with a 50 : 50 mixture of
kerosene (paraffin) and machine oil.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect the spark plug wire, and make sure all moving parts have come to a com-
plete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.
Wear gloves to protect hands from sharp edges and hot surfaces.
If you have any questions or problems, please contact your dealer.
CAUTION
Over lubricating can cause the gear case to operate
sluggishly and can cause grease to leak out.
CAUTION
Wear gloves to protect hands from sharp blades.
Failure to observe these precautions could lead to injury.
15
Maintenance and care
Cutter blade adjustment
Standard blades require no periodic adjustments. Make sure all
blade bolts (A) are tight and in good condition.
16
Storage
Storage
Storage hook installation
1. Insert small end of hook into locating hole on attachment
shaft.
2. Slide plastic cap onto end of attachment shaft.
17
Specifications
Specifications
These specifications are subject to change without notice.
MTA-AHS-HD
External dimensions:
Length x Width x Height mm 966 × 122 × 95
Masses kg 2.1
Cutting attachment:
Type Dual action, double sided blade
Cutting length mm 536
Pitch mm 35
Height mm 21
Gear ratio and lubrication: 4.60 reduction and good quality lithium grease
Vibration levels: (ISO 10517) ahv,eq
Front handle / Rear handle m/s² 7.8 / 6.9
m/s² 8.1 / 6,5 (with MTA-3EXT)
Uncertainty: K m/s² 5.0
Sound pressure level: (ISO 10517) LpAd(=LpAeq +KpA)dB (A)97.0
Uncertainty: KpA dB (A) 2.5
Sound power level: (ISO 10517) LWAd(=LWAeq +KWA) dB (A) 108.0
Uncertainty: KWA dB (A) 2.5
Applicable model PAS-2620ES and M262S
18
Declaration of conformity
Declaration of conformity
The undersigned manufacturer:
YAMABIKO CORPORATION
1-7-2 Suehirocho
Ohme, Tokyo 198-8760
JAPAN
This declaration of conformity is issued under the sole responsibility of the manufacturer.
declares that the hereunder specified new unit:
PRO ATTACHMENT SERIES
Type: PAS-2620ES + MTA-AHS-HD
Multi-tool System
Type: M262S + MTA-AHS-HD
complies with:
* the requirements of Directive 2006/42/EC (use of harmonized standard EN ISO 10517: 2019)
* the requirements of Directive 2014/30/EU (use of harmonized standard EN ISO 14982: 2009, EN 55012: 2007+A1:
2009)
* the requirements of Directive 2011/65/EU (use of harmonized standard EN IEC 63000: 2018)
* the requirements of Directive 2000/14/EC
Conformity assessment procedure followed ANNEX V
Measured sound power level :106 dB(A)
Guaranteed sound power level :109 dB(A)
Serial Number U65940001001 to U65940100000
Tokyo, October 18th, 2022
YAMABIKO CORPORATION
The authorized representative in Europe who is authorized to
compile the technical file.
Company: CERTIFICATION EXPERTS B.V.
Address: Amerlandseweg 7, 3621 ZC Breukelen, The Nether-
lands
Hisashi Kobayashi Mr. Richard Glaser
General Manager
Quality Assurance Dept.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Shindaiwa MTA-AHS-HD Manuel utilisateur

Catégorie
Taille-haies électriques
Taper
Manuel utilisateur