Kenmore 593 . 66122700 Manuel utilisateur

Marque: Kenmore

Modèle: 593 . 66122700

Taper: Manuel utilisateur

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Sears

Canada, Inc., Toronto, Ontario, Canada M5B 2B8

RAN

ÇAIS E

Part No. 12828180

Form C/12/06

www.sears.com

Canada, www.sears.ca

Bottom Freezer Refrigerator*

Use & Care Guide

Réfrigérateur à compartiment congélateur inférieur*

Guide d'utilisation et d'entretien

Refrigerador con congelador inferior*

Guía de Uso y Cuidado

* See model numbers on inside back cover for models referenced

* Voir sur troisième de couverture les numéros de modèle auxquels il est fait référence.

* Ver los números de modelos en el interior de la contraportada para los modelos respectivos.

Important safety information

What you need to know

about safety

instructions

Warning and Important Safety

Instructions appearing in this manual are

not meant to cover all possible

conditions and situations that may occur.

Common sense, caution, and care must

be exercised when installing,

maintaining, or operating refrigerator.

Always contact your dealer, distributor,

service agent, or manufacturer about

problems or conditions you do not

understand.

Save these instructions

DANGER – Immediate hazards

which WILL result in severe personal

injury or death.

DANGER

WARNING – Hazards or unsafe

practices which COULD result in

severe personal injury or death.

WARNING

CAUTION – Hazards or unsafe

practices which COULD result in

minor personal injury.

CAUTION

To reduce risk of injury or death,

follow basic precautions, including

the following:

IMPORTANT: Child entrapment and

suffocation are not problems of the

past. Junked or abandoned

refrigerators are still dangerous –

even if they sit out for “just a few

days.” If you are getting rid of your

old refrigerator, please follow the

instructions below to help prevent

accidents.

Before you throw away your old

refrigerator or freezer:

➢ Take off the doors.

➢ Leave the shelves in

place so children

may not easily climb

inside.

DANGER

RECOGNIZE SAFETY

SYMBOLS, WORDS,

LABELS

To reduce risk of fire, electric shock, serious injury or

death when using your refrigerator, follow these basic

precautions, including the following:

1. Read all instructions

before

using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not sure this

appliance is properly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate 115

volt, 15 amp., 60 cycle line.

8. Do not modify plug on power cord. If plug does not fit

electrical outlet, have proper outlet installed by a

qualified electrician.

9. Do not use a two-prong adapter, extension cord or

power strip.

10. Do not remove warning tag from power cord.

11. Do not tamper with refrigerator controls.

12. Do not service or replace any part of refrigerator unless

specifically recommended in Use & Care Guide or

published user-repair instructions. Do not attempt

service if instructions are not understood or if they are

beyond personal skill level.

13.

Always

disconnect refrigerator from electrical supply

before attempting any service. Disconnect power cord

by grasping the plug, not the cord.

14. Install refrigerator according to Installation Instructions.

All connections for water, electrical power and grounding

must comply with local codes and be made by licensed

personnel when required.

15. Keep your refrigerator in good condition. Bumping or

dropping refrigerator can damage refrigerator or cause

refrigerator to malfunction or leak. If damage occurs,

have refrigerator checked by qualified service

technician.

16. Replace worn power cords and/or loose plugs.

17.

Always

read and follow manufacturer’s storage and ideal

environment instructions for items being stored in

refrigerator.

18. Your refrigerator should not be operated in the

presence of explosive fumes.

19. Children should not climb, hang or stand on any part of

the refrigerator.

20. Clean up spills or water leakage associated with water

installation.

WARNING

ENGLISH FRANÇAIS ESPAÑOL

Protection agreements

Master protection

agreements

IN THE U.S.A.

Congratulations on making a smart

purchase. Your new Kenmore

appliance is designed and manufactured

for years of dependable operation. But

like all products, it may require

preventive maintenance or repair from

time to time. That is when having a

Master Protection Agreement can save

you money and aggravation.

Purchase a Master Protection

Agreement now and protect yourself

from unexpected hassle and expense.

The Master Protection Agreement also

helps extend the life of your new

appliance. Here is what is included in

the agreement:

➢ Expert service by our 12,000

professional repair specialists.

➢ Unlimited service and no charge for

parts and labor on all covered

repairs.

➢ “No-lemon” guarantee – replacement

of your covered product if more than

three product failures occur within

twelve months.

➢ Product replacement if your covered

product cannot be fixed.

➢ Annual Preventive Maintenance

Check at your request – no extra

charge.

➢ Fast help by phone – non-technical

and instructional assistance on

products repaired in your home, plus

convenient repair scheduling.

➢ Power surge protection against

electrical damage due to power

fluctuations.

➢ Rental reimbursement if repair of

your covered product takes longer

than promised.

Once you purchase the Agreement, a

simple phone call is all that it takes for

you to schedule service. You can call

anytime day or night, or schedule a

service appointment online.

Sears has over 12,000 professional

repair specialists, who have access to

over 4.5 million quality parts and

accessories. That is the kind of

professionalism you can count on to

help prolong the life of your new

purchase for years to come. Purchase

your Master Protection Agreement

today!

Some limitations and exclusions apply.

For prices and additional information,

call 1-800-827-6655.

Sears Installation Service

For Sears guaranteed professional

installation of home appliances and

items like garage door openers and

water heaters, in the U.S.A. call

1-800-MY-HOME

Maintenance agreements

IN CANADA

Your purchase has added value because

you can depend on Sears HomeCentral

for service. With over 2,400 service

technicians and access to over 900,000

parts and accessories, we have the

tools, parts, knowledge and skills to

ensure our pledge: We Service What

We Sell.

Your Kenmore

appliance is designed,

manufactured and tested to provide

years of dependable operation. Yet any

major appliance may require service

from time to time. The Sears

Maintenance Agreement offers you an

outstanding service program, affordably

priced.

Sears Maintenance Agreement

➢ Is your way to buy tomorrow’s service

at today’s price.

➢ Eliminates repair bills resulting from

normal wear and tear.

➢ Provides for non-technical and

instructional assistance.

➢ Even if you don’t need repairs,

provides an annual Preventive

Maintenance Check, at your request,

to ensure that your appliance is in

proper running condition.

Some limitations apply. For information

concerning Sears Canada Maintenance

Agreements, call 1-800-361-6665.

Product record

In the space below record the model

and serial numbers and purchase date

of your refrigerator. You will find the

model and serial number sticker inside

the refrigerator section on the left wall.

Model Number: 596. _______________

Serial Number: ____________________

Purchase Date: ____________________

Keep this booklet and your Sears

sales receipt in a safe place for future

reference.

Reverse Osmosis

Water Systems

Some Reverse Osmosis home

water systems cause low water

pressure. Low water pressure

can affect the water and ice

dispensing system by causing

small or hollow ice cubes and

slow water flow from the

dispenser. Service problems

related to the home’s Reverse

Osmosis water system are not

covered by the warranty.

Warranty

One Year Limited Warranty

When installed, operated and

maintained according to all

instructions supplied with the

product, if this appliance fails due to

a defect in material or workmanship

within one year from the date of

purchase, call 1-800-4-MY-HOME

to arrange for free repair.

If this appliance is used for other

than private family purposed, this

warranty applies for only 90 days

from the date of purchase.

This warranty covers only defects

in material and workmanship.

Sears will NOT pay for:

1. Expendable items that can wear

out from normal use, including

but not limited to filters, belts,

light bulbs, and bags.

2. A service technician to instruct

the user in correct product

installation, operation or

maintenance.

3. A service technician to clean or

maintain this product.

4. Damage to or failure of this

product if it is not installed,

operated or maintained according

to all instructions supplied with

the product.

5. Damage to or failure of this

product resulting from accident,

abuse, misuse or use for other

than its intended purpose.

6. Damage to or failure of this

product caused by the use of

detergents, cleaners, chemicals

or utensils other than those

recommended in all instructions

supplied with the product.

7. Damage to or failure of parts or

systems resulting

from unauthorized modifications

made to this

product.

Disclaimer of implied warranties;

limitation of remedies

Customer’s sole and exclusive

remedy under this limited warranty

shall be product repair as provided

herein. Implied warranties, including

warranties of merchantability or

fitness for a particular purpose, are

limited to one year or the shortest

period allowed by law. Sears shall

not be liable for incidental or

consequential damages. Some

states and provinces do not allow

the exclusion or limitation of

incidental or consequential

damages, or limitations on the

duration of implied warranties or

merchantability or fitness, so these

exclusions or limitations may not

apply to you.

This warranty applies only while this

appliance is used in the United

States and Canada.

This warranty gives you specific

legal rights, and you may also have

other rights which vary from state to

state.

Sears, Roebuck and Co., Dept.

817WA, Hoffman Estates, IL 60179

Sears Canada Inc., Toronto,

Ontario, Canada

M5B 2B8

Warranty

ENGLISH FRANÇAIS ESPAÑOL

Contents

Important Safety Information ......................................................................................2

What You Need to Know About Safety Instructions...................................................2

Protection Agreements ................................................................................................3

Master Protection Agreements – U.S.A.....................................................................3

Maintenance Agreements – Canada .........................................................................3

Warranty.....................................................................................................................4

Product Record ..........................................................................................................4

Installing Your Refrigerator ....................................................................................6-11

Measuring the Opening .............................................................................................6

Transporting Your Refrigerator...................................................................................6

Selecting the Best Location .......................................................................................6

How to Install and Remove Handles .........................................................................7

How to Remove the Hinges, Doors and Drawer .......................................................8

How to Reverse the Hinges, Doors and Drawer .......................................................9

How to Replace the Hinges, Doors and Drawer........................................................9

How to Connect the Water Supply...........................................................................10

How to Level Your Refrigerator ................................................................................11

Setting and Maintaining Proper Temperatures........................................................12

Initial Control Settings..............................................................................................12

Adjusting the Controls..............................................................................................12

Fresh Food Storage.................................................................................................12

Frozen Food Storage...............................................................................................12

Fresh Food Features.............................................................................................13-14

Interior Shelves ........................................................................................................13

Door Storage............................................................................................................13

Climate-Controlled Drawers.....................................................................................14

Storage Drawers ......................................................................................................14

Freezer Features .........................................................................................................15

Automatic Ice Maker ................................................................................................15

Shelves ....................................................................................................................15

Drawers....................................................................................................................15

Door Storage............................................................................................................15

Hints and Care .......................................................................................................16-17

How to Clean Your Refrigerator ...............................................................................16

How to Remove Odors from Refrigerator ................................................................17

Energy Saving Ideas................................................................................................17

How to Remove and Replace Light Bulbs...............................................................17

Normal Operating Sounds .........................................................................................18

Troubleshooting ....................................................................................................19-20

Operation ............................................................................................................19-20

Ice and Water...........................................................................................................20

Français .......................................................................................................................21

Español........................................................................................................................41

Service ..........................................................................................................Back Cover

Contents

Installing your refrigerator

Your refrigerator was packed carefully

for shipment. Remove and discard shelf

packaging and tape. Do not remove the

serial plate.

Measuring the opening

A one-half inch (

⁄2") of air space must be

provided for the top and the back of the

refrigerator. When installing your

refrigerator, measure carefully.

Subflooring or floor coverings (i.e.

carpet, tile, wood floors, rugs) may make

your opening smaller than anticipated.

Some clearance may be gained by

using the leveling procedure under

How to Level Your Refrigerator

(page 11).

IMPORTANT: If refrigerator is to be

installed into a recess where top of

refrigerator is completely covered, use

dimensions from floor to top of hinge

cap to verify proper clearance.

Selecting the best

location

Observe these points when choosing the

final location for your refrigerator:

➢ DO NOT install refrigerator near

oven, radiator or other heat source. If

not possible, shield refrigerator with

cabinet material.

➢ DO NOT install where temperature

falls below 55° F (13° C). Malfunction

may occur at this temperature.

➢ To assure proper door closure, follow

the leveling instructions in the

section, How to Level Your

Refrigerator

(page 11).

Transporting your

refrigerator

Follow these tips when moving the

refrigerator to final location:

➢ NEVER transport refrigerator on its

side. If an upright position is not

possible, lay refrigerator on its back.

Allow refrigerator to sit upright for

approximately 30 minutes prior to

plugging refrigerator in to assure oil

returns to the compressor. Plugging

refrigerator in immediately may cause

damage to internal parts.

➢ Use an appliance dolly when moving

refrigerator.

ALWAYS truck

refrigerator from its side or

back–NEVER from its front.

➢ Protect outside finish of refrigerator

during transport by wrapping cabinet

in blankets or inserting padding

between the refrigerator and dolly.

➢ Secure refrigerator to dolly firmly with

straps or bungee cords. Thread

straps through handles when

possible. DO NOT overtighten. Over-

tightening restraints may dent or

damage outside finish.

ENGLISH FRANÇAIS ESPAÑOL

How to install and

remove handles

For easier installation, some

refrigerators may have been delivered

with the handles off. Please see the

interior of the fresh food section to

locate the handle assembly.

Handle design may vary from

refrigerator to refrigerator. Please

reference the instructions for the

appropriate handle design below.

Before handle installation, remove all

packaging and tape.

FRESH FOOD HANDLE

Installing Front-Mounted Handle

1. Remove

⁄4" hex head

screws from door face

with hex head driver.

Remove Phillips screw

from top of door.

• If reversing door, remove door plugs

from opposite side of door and

insert in screw holes.

2. Align handle holes with screw

holes on door face

and secure with 2

door face screws

from step 1.

NOTE: Do not reinstall top screw at

this step.

3. Locate handle trim in

literature pack and install

over top and bottom of

handle, as illustrated.

• Secure top handle trim

with remaining screw

removed in step 1.

• Snap bottom trim over bottom

portion of handle.

* Fasteners may require either a T-15 Torx

driver or a Phillips screwdriver.

Torx

is a registered trademark of Textron Inc.

FREEZER HANDLE

Installing Partial-Width Handle

➢ Remove screws from

the top of door.

➢ Install handle by

fastening with

screws removed

from the top of door.

• If reversing freezer

door, remove door

plugs from opposite top edge of

door and insert into screw holes.

Removing Partial-Width Handle

➢ Remove handle

screws.*

• Retain screws for

later replacement.

Installing Full-Width Handle

➢ Remove the screws

on the top of door.

➢ Install handle by

fastening with

screws* removed

from edge of door.

Removing Full-Width Handle

➢ Remove handle by

removing screws*

from handle.

• Retain screws for later

replacement.

Removing Front-Mounted Handle

1. Remove top handle trim

by removing top handle

screw.

• Retain trim and screw

for later replacement.

2. Pry bottom handle trim

from handle with

screwdriver flat blade

wrapped in masking tape.

• Retain trim for later

replacement.

3. Remove two remaining

handle screws and

remove handle.

• Retain screws for later

replacement.

Installing Side-Mounted Handle

➢ Remove screws from the side of the

door.*

➢ Install handle by

fastening with the

screws removed

from edge of door.

NOTE: If reversing door, remove door

plugs from opposite side of door and

insert in screw holes.

Removing Side-Mounted Handle

➢ Remove handle by

removing three

screws* from side of

door.

• Retain screws for later replacement.

Installing your refrigerator, cont.

How to remove the

hinges, doors and

drawer

Some installations require door removal

to get refrigerator to final location.

5. Lift refrigerator door from center

hinge pin.

For freezer door only:

Hold freezer door in

place while removing

center hinge pin with a

⁄16" hex head driver.

Remove freezer door

from bottom hinge.

• Retain hinge pin for later use.

For freezer drawer only: Remove

center hinge pin with a

⁄16" hex head

driver.

• Retain hinge pin for later use.

7. Remove Phillips

screws to remove

center hinge.

• Retain all screws

for later use.

8. Remove bottom hinge or stabilizing

bracket with

⁄8" hex head driver.

• Retain

screws for

later use.

• Lift out

bottom hinge

pin (some

models).

PULLOUT DRAWER

(SOME MODELS)

To avoid electrical shock which can

cause severe personal injury or

death, observe the following:

➢ Disconnect power to refrigerator

before removing doors. Connect

power only after replacing doors.

WARNING

To avoid damage to walls and

flooring, protect soft vinyl or other

flooring with cardboard, rugs or other

protective material.

CAUTION

1. Unplug power cord from power

source.

2. Remove toe grille and bottom bracket

cover(s) (page 11).

3. Remove top hinge

cover from refrigerator

door by removing

Phillips screw.

• Retain screw and

cover for

replacement.

4. Unscrew

⁄16" hex head

screws from top hinge

to remove hinge.

• Retain all screws for

later use.

To avoid possible injury, product, or

property damage, you will need two

people to perform the following

instructions.

CAUTION

1. Pull drawer open to full extension.

2. Remove lower basket by pressing

inward on basket sides, then lift

basket.

3. Pull upper basket out to full

extension, and lift out to remove.

Press Tab Here

4. Remove Phillips screw from each side

of rail system (some models).

5. Lift top of door to unhook door

supports from rail system. Lift door out

to remove.

ENGLISH FRANÇAIS ESPAÑOL

How to reverse the

hinges, doors and

drawer

1. Perform all steps listed in How to

Remove the Hinges, Doors and

Drawer (page 8).

2. Transfer cabinet

plugs and cabinet

screws to opposite

side of cabinet.

• Remove cabinet

plugs with flat

blade of

screwdriver tip

wrapped in

masking tape.

• Remove center mullion screws with

⁄16" hex head driver.

• For freezer door only: Remove

bottom mullion screws with

⁄8" hex

head driver.

IMPORTANT: When working directly on

doors, place doors on a nonabrasive

surface protected by towels or rugs to

avoid damage to door finish.

3. Transfer door stops from bottom edge

of fresh food door and freezer door

(some models) to

opposite side of

door edge.

• Use a Phillips

screwdriver for

removal and installation.

4. See How to Install and Remove

Handles to remove and reinstall

handles (page 7).

5. Proceed to How to Replace the

Hinges, Doors and Drawer to mount

doors.

How to replace the

hinges, doors and

drawer

1. Install hinge assemblies.

• Install top hinge loosely with

⁄16" hex

head screws.

• Install center hinge with Phillips

screws.

• Install bottom hinge with

⁄8" hex

head screws.

2. Insert bottom

hinge pin

(some models).

• Locate bottom

hinge hole

closest to

outside edge

of cabinet,

and insert bottom hinge pin.

Replace any door shims, if present.

3. Replace toe grille and bracket

cover(s). See markings on inside of

toe grille to insure proper placement.

• Snap bottom portion into place

first. Press down on top part of grille

until top portion snaps into place.

4. For freezer door

only: Place hinge

side of freezer

door on bottom

hinge pin. Hold

freezer door

upright while installing center hinge

pin with

⁄16" hex head driver.

• Replace any applicable door shims.

• Make sure the hinge pin is installed

tightly.

For freezer drawer only: Install

center hinge pin with

⁄16" hex head

driver.

• Replace any applicable door shims.

• Make sure the hinge pin is installed

tightly.

5. Place hinge side of refrigerator door

on center hinge pin.

6. While holding

refrigerator door

upright, tighten

down top hinge

with

⁄16" hex head

driver and replace

hinge cover (some

models).

PULLOUT DRAWER

1. Pull both rails out to full extension.

2. Hook door supports into rail tabs, as

illustrated, and lower door into final

position.

3. With drawer pulled out to full

extension, insert lower basket by

aligning tabs on both side of lower

basket with notches in rail assembly.

4. Slide upper basket into unit. Make

sure that rear of basket hooks behind

rail catch.

Installing your refrigerator, cont.

How to connect the

water supply

To reduce the risk of injury or

death, follow basic precautions,

including the following:

➢ Read all instructions before

installing device.

➢ DO NOT attempt installation if

instructions are not understood or

if they are beyond personal skill

level.

➢ Observe all local codes and

ordinances.

➢ DO NOT service device unless

specifically recommended in Use

and Care Guide or published user-

repair instructions.

➢ Disconnect power to refrigerator

prior to installing device.

WARNING

To avoid property damage or

possible injury, follow basic

precautions, including the

following:

➢ Consult a plumber to connect

copper tubing to household

plumbing to assure compliance

with local codes and ordinances.

➢ Confirm water pressure to water

valve is between 20 and 100

pounds per square inch. If water

filter is installed, water pressure to

water valve must be a minimum of

35 pounds per square inch.

➢ DO NOT use a self-piercing, or

⁄16"

saddle valve! Both reduce water

flow, become clogged with time,

and may cause leaks if repair is

attempted.

➢ Tighten nuts by hand to prevent

cross threading. Finish tightening

nuts with pliers and wrenches. Do

not overtighten.

➢ Wait 24 hours before placing

refrigerator into final position to

check and correct any water leaks.

CAUTION

MATERIALS NEEDED

➢

⁄4" outer diameter flexible copper

tubing

➢ Brass compression nut and sleeve for

⁄4" outer diameter copper tubing.

➢ Shut-off valve (requires a

⁄4" hole to

be drilled into water supply before

valve attachment)

➢ Adjustable wrench

➢

⁄4" hex nut driver

NOTE: Add 8' to tubing length needed to

reach water supply for creation of

service loop.

1. Create service loop with tubing using

care to avoid kinks in tubing.

2. Remove plastic cap from water valve

inlet port.

3. Place brass nut (A) and sleeve (B) on

copper tube end as illustrated.

4. Place end of copper tubing into water

valve inlet port. Shape tubing slightly –

DO NOT KINK – so that tubing feeds

straight into inlet port.

5. Slide brass nut over sleeve and

screw nut into inlet port. Tighten nut

with wrench.

IMPORTANT: DO NOT overtighten.

Cross threading may occur.

6. Pull on tubing to confirm connection

is secure. Connect tubing to frame

with water tubing clamp (C) and turn

on water supply. Check for leaks and

correct, if present.

7. Monitor water connection for 24

hours. Correct leaks, if necessary.

ENGLISH FRANÇAIS ESPAÑOL

How to level your

refrigerator

If your refrigerator requires an ice maker

water supply connection, refer to How

to Connect the Water Supply (page

10) section before leveling your

refrigerator.

To protect personal property or

refrigerator from damage, observe

the following:

➢ Protect soft vinyl or other flooring

with cardboard, rugs, or other

protective material.

➢ Do not use power tools when

performing leveling procedure.

CAUTION

MATERIALS NEEDED

➢

⁄8" hex head driver

➢ Carpenters Level

1. Remove toe grille:

➢ Grasp toe grille firmly and pull

outward to unclip.

5. Turn stabilizing legs (C) clockwise

until firmly against floor.

6. Turn front adjustment screws (A) 2 to

3 times counterclockwise, so that full

weight of refrigerator rests on

stabilizing legs (C).

4. Select models also have rear

adjustment screws (B). Using the hex

head driver, turn each of these

adjustment screws (B) to raise or

lower the rear of the refrigerator.

7. Using a level, make sure the

refrigerator is level from side to side

and the front of refrigerator is

⁄4"

(6 mm) or

⁄2 bubble higher than back

of refrigerator.

8. Replace the lower bracket cover

(if applicable):

➢ Position the cover(s) on the outer

edge of the lower hinge. Swing

the cover(s) toward the cabinet

and snap into place.

2 Remove bottom bracket cover

(if applicable):

➢ Use the eraser end of a pencil or

similar blunt tool and place in the

notch. Use slight pressure to pry

the cover from the lower hinge

bracket.

➢ Continue to maintain downward

pressure to the notched side of

the cover while swinging it off.

3. Using hex head driver, turn front

adjustment screws (A) clockwise to

raise and counterclockwise to lower

the front of the refrigerator.

Notch

Location

9. Reinstall the toe grille.

➢ See markings on the inside of

the toe grille to insure proper

placement.

➢ Align the toe grille mounting clips

with the lower cabinet slots and

snap bottom portion into place

first.

➢ Press on the top part of the grille

until it snaps into place.

➢ Push the toe grille firmly and

snap into place.

NOTE: Some models only have

adjustment screws “A.”

Initial control settings

After plugging the refrigerator in, set the

controls.

➢ Pressing the or pads adjusts the

controls to the desired setting.

➢ The temperature control range for both

compartments is 1 through 7 (coldest).

➢ Initially set the refrigerator control on 4.

➢ Initially set the freezer control on 4.

➢ Let the refrigerator run at least 8 to 12

hours before adding food.

Setting and maintaining proper temperatures

The controls are located at the top front of the refrigerator and freezer compartments. NOTE: The freezer control turns the cooling

system on. Neither section will cool if freezer control is set to off.

Refrigerator Control

Freezer Control

Initial control settings

1. Locate refrigerator control at the top

of fresh food compartment and

freezer control at top of freezer

section.

2. The manufacturer’s recommended

setting for both compartments is 4.

3. Let the refrigerator run at least 8 to

12 hours before adding food.

4. Allow 24 hours for temperature to

stabilize.

Adjusting the controls

➢ 24 hours after adding food, you may

decide that one or both

compartments should be colder or

warmer. If so, adjust the control(s) as

indicated in the Temperature Control

Guide.

➢ Do not change either control more

than one number at a time.

➢ Allow 5-8 hours for temperatures to

stabilize.

TEMPERATURE CONTROL GUIDE

Refrigerator too warm Turn the refrigerator control to next higher number.

Refrigerator too cold Turn the refrigerator control to next lower number.

Freezer too warm Turn the freezer control to next higher number.

Freezer too cold Turn the freezer control to next lower number.

To turn refrigerator OFF Turn the freezer control to OFF.

Check after 24 hours. If the

temperature is above 40° F adjust the

controls as explained above.

Frozen food storage

➢ The freezer compartment of a

refrigerator should be kept at

approximately 0° F. To check the

temperature, place an appliance

thermometer between the frozen

packages and check after 24 hours. If

the temperature is above 0˚ F, adjust

the control as described above.

➢ Changing either control will have

some effect on the temperature of the

other compartment.

Fresh food storage

➢ The fresh food compartment of a

refrigerator should be kept between

34° F and 40° F with an optimum

temperature of 37° F. To check the

temperature, place an appliance

thermometer in a glass of water and

place in the center of the refrigerator.

Touch Temperature Controls

(SELECT MODELS)

TEMPERATURE CONTROL GUIDE

Refrigerator too warm Set the refrigerator control to next higher number

by pressing the pad

Refrigerator too cold Set the refrigerator control to next lower number by

pressing the pad.

Freezer too warm Set the freezer control to next higher number by

pressing the pad.

Freezer too cold Set the freezer control to next lower number by

pressing the pad.

To turn refrigerator OFF Press the refrigerator or freezer pad until a dash

(–) appears in the display.

Freezer Control

Control

NOTE: Turning freezer control to OFF stops cooling in both compartments. It does

not shut off power to the refrigerator.

NOTE: Turning freezer control to OFF stops cooling in both compartments. It does

not shut off power to the refrigerator.

ENGLISH FRANÇAIS ESPAÑOL

Door storage

DAIRY CENTER

The Dairy Center

provides convenient

storage for items

such as butter,

yogurt, cheese, etc.

This compartment is an adjustable

feature located in the door. It can be

moved to several different locations to

accommodate storage needs.

➢ To remove, open dairy door, pull

upward and tilt out.

➢ To install, reverse above procedure.

DOOR BUCKETS

Door Buckets adjust to

meet individual storage

needs.

➢ To remove,

slide bucket up

and pull

straight out.

➢ To install, reverse above procedure.

Fresh food features

Interior shelves

To avoid personal injury or property

damage, observe the following:

➢ Confirm shelf is secure before

placing items on shelf.

➢ Handle tempered glass shelves

carefully. Shelves may break

suddenly if nicked, scratched, or

exposed to sudden temperature

change.

CAUTION

SPILLPROOF SHELVES

(SOME MODELS)

Spillproof Shelves hold

simple spills for easier

cleaning.

➢ To remove shelves, lift

up and out.

➢ To install shelves, reverse above

procedure.

Spillproof Slide-out

Shelves feature

the convenience

of easy cleaning

with a pullout

design to reach items in the back. For

ease of cleaning, glass shelf may be

removed by pulling to full extension and

lifting out of frame.

DOOR RETAINER

Door Retainers remove for easy

cleaning.

➢ To remove, slide retainer up and pull

straight out.

➢ To install, reverse above procedure.

Fresh food features, cont.

Climate-controlled

drawers

HUMIDITY-CONTROLLED

CRISPER DRAWERS

The Crisper Drawer

keeps produce fresh

longer by providing

an environment with

adjustable humidity.

Controls

The crisper

controls

regulate the

amount of humidity in the crisper drawer.

Use the

low

setting for produce with

outer skins. Use the

high

setting for

leafy produce.

To remove and install drawers:

➢ To remove drawer, pull drawer out to

full extension. Tilt up front of drawer

and pull straight out.

➢ To install, insert drawer into frame

rails and push back into place.

To remove and install glass and

frame:

➢ Remove drawers as instructed

above.

➢ Place hand beneath frame to push up

glass from underneath. Lift glass out.

➢ Lift frame from refrigerator liner rails.

➢ To install, repeat above instructions in

reverse order.

WHAT CAN I DO TO PROLONG

THE LIFE OF MY PRODUCE?

Please observe the following rules when

storing produce in humidity-controlled

crisper drawers:

➢ DO NOT wash produce before

placing in crispers. Any additional

moisture added to the drawers may

cause produce to prematurely spoil.

➢ DO NOT line crispers with paper

towels. Towels will retain moisture.

➢ Follow control instructions carefully.

Not setting controls correctly may

damage produce.

See below for correct humidity drawer

control settings:

LOW • cauliflower • apples

• corn • oranges

• zucchini • grapes

• cucumbers

HIGH • lettuce • asparagus

• spinach • cabbage

• celery • broccoli

• fresh sprouts • fresh herbs

Storage drawers

SNACK DRAWER

(SOME MODELS)

The Snack Drawer

can be used for

storage of food

items or extra

produce.

To remove and install drawers:

➢ To remove drawer, pull drawer out to

full extension. Tilt up front of drawer

and pull straight out.

➢ To install, insert drawer into frame

rails and push back into place.

CAN RACK

(SOME MODELS)

The Can Rack slides out from

underneath the spillproof stationary

shelf. The can rack holds up to twelve

12-ounce beverage cans.

To remove and install can rack:

➢ To remove can rack, pull can rack out

to full extension. Tilt up front of can

rack and pull straight out.

➢ To install, insert can rack into frame

rails and push back into place.

ENGLISH FRANÇAIS ESPAÑOL

Freezer features

Automatic ice maker

(SOME MODELS)

Using Ice Maker for the First Time

1. Confirm ice bin is in

place and ice maker

arm is down.

2. After freezer section reaches

between 0° to 2° F (-18° to -17° C),

ice maker fills with water and begins

operating.

3. Allow approximately 24 hours after

installation to receive first harvest of

ice.

4. Discard ice created within first 12

hours of operation to verify system is

flushed of impurities.

Operating Instructions

1. Confirm ice bin is in place and ice

maker arm is down.

2. After freezer section reaches 0° to 2°

F (-18° to -17° C), ice maker fills with

water and begins operating. You will

have a complete harvest of ice

approximately every 3 hours.

3. Stop ice production

by raising ice maker

arm until click is

heard.

4. Ice maker will remain in the

off

position until arm is pushed down.

To avoid property damage, observe

the following:

➢ Do not force ice maker arm down

or up.

➢ Do not place or store anything in

ice storage bin.

CAUTION

Shelves

ICE SERVICE RACK

(SOME MODELS)

To install and remove rack:

➢ To install, slide

L-shaped

groove of shelf

down over back

wall screw.

Push rack back until screw is stopped

in L-shaped groove (1) . Slide front

portion of shelf over front wall screw

(2).

➢ To remove, perform above steps in

reverse order.

FIXED FREEZER SHELF

(SOME MODELS)

To remove and install shelves:

➢ Remove shelf

by pulling out

to full

extension. Tilt

up front of

shelf and pull straight out.

➢ To install, insert shelf into refrigerator

liner rails and push to back of

compartment.

Drawers

WIRE BASKET

(SOME MODELS)

To remove and install basket:

➢ To remove

basket, pull

basket out

to full

extension.

Tilt up front of basket and pull straight

out.

➢ To install, insert basket into

refrigerator liner rails and push back

into place.

PULLOUT DRAWER

BASKETS

(SOME MODELS)

(Door assembly of drawer removed from

illustration for visual clarity.)

To remove baskets:

➢ Follow steps 1-3 of Pullout Drawer

(page 8).

To replace baskets:

➢ Follow steps 3-4 of Pullout Drawer

(page 9).

To prevent accidental child

entrapment or suffocation risk, DO

NOT remove the divider in the top

freezer basket.

DANGER

Door storage

DOOR SHELF

(SOME MODELS)

The Door Shelf provides convenient

storage for frozen food items in freezer

door.

To remove and install door shelf:

➢ To remove shelf,

lift assembly from

side liner tabs

and pull out.

➢ To install, fit ends

of shelf assembly on

liner tabs and slide down.

Hints and care

PART DO

➢ Use 4 tablespoons of baking soda dissolved in 1 quart

(1 liter) warm soapy water.

➢ Rinse surfaces with clean warm water and dry immediately

to avoid water spots.

➢ Use warm, soapy water and a soft, clean cloth or sponge.

➢ Rinse surfaces with clean warm water and dry immediately

to avoid water spots.

➢ Use a vacuum cleaner hose nozzle.

➢ Use a vacuum cleaner hose nozzle with brush attachment.

➢ Follow removal and installation instructions from appropriate

feature section.

➢ Allow items to adjust to room temperature.

➢ Dilute mild detergent and use a soft clean cloth or sponge

for cleaning.

➢ Use a plastic bristle brush to get into crevices.

➢ Rinse surfaces with clean warm water.

➢ Dry glass and clear items immediately to avoid spots.

DO NOT USE

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Vinegar-based products

➢ Citrus-based cleaners

➢ Abrasive or harsh cleaners

➢ Metal or plastic-textured

scouring pads

➢ A dishwasher

Textured Doors

and Exterior

Cabinet Interior

Stainless Steel Doors

and Exterior*

IMPORTANT:

Damage

to stainless steel finish

due to improper use of

cleaning products or

non-recommended

products is not covered

under this product’s

warranty.

Door Gaskets

Condenser Coil

Remove base grille to

access

Condenser Fan Outlet

Grille

See back of refrigerator

Accessories

Shelves,

buckets, drawers, etc.

To avoid personal injury or property damage, observe the following:

• Read and follow manufacturer’s directions for all cleaning products.

• DO NOT place buckets, shelves or accessories in dishwasher. Cracking or

warping of accessories may result.

CAUTION

To avoid electrical shock which can

cause severe personal injury or

death, disconnect power to

refrigerator before cleaning. After

cleaning, connect power.

WARNING

How to clean your refrigerator

* A stainless steel cleaner has been included inside the refrigerator for your use. To purchase additional cleaner, please contact

Sears using the information on the back of your manual.

ENGLISH FRANÇAIS ESPAÑOL

How to remove odors

from refrigerator

1. Remove all food.

2. Disconnect refrigerator.

3. Clean the following items–paying

special attention to crevices–using

the appropriate instructions in

How to

Clean Your Refrigerator

• Walls, floor and ceiling of cabinet

interior.

• Drawers, shelves and gaskets.

4. Wash and dry all bottles, containers

and jars. Discard spoiled or expired

items.

5. Wrap or store odor-causing foods in

tightly-sealed containers to prevent

reoccurring odors.

6. Connect power to refrigerator and

return food.

7. After 24 hours, check if odor has

been eliminated.

If odor is still present...

1. Remove drawers and place on top

shelf of refrigerator.

2. Pack refrigerator and freezer

sections–including doors–with

crumpled sheets of black and white

newspaper.

3. Place charcoal briquettes randomly

on crumpled newspaper in both

freezer and refrigerator

compartments.

4. Close doors and let stand 24–48 hours.

5. Repeat steps 5 through 7 above.

If odor was not eliminated, contact

Sears Service Center. Refer to back of

manual for phone number.

Energy saving ideas

➢ Avoid overcrowding refrigerator

shelves. This reduces effectivity of air

circulation around food and causes

refrigerator to run longer.

➢ Avoid adding too much warm food to

refrigerator at one time. This

overloads compartments and slows

rate of cooling.

➢ Do not use aluminum foil, wax paper,

or paper toweling as shelf liners. This

decreases air flow and causes

refrigerator to run less efficiently.

➢ A freezer that is

⁄3 full runs most

efficiently.

➢ Locate refrigerator in coolest part of

room. Avoid areas of direct sunlight,

or near heating ducts, registers, or

other heat producing appliances. If

this is not possible, isolate exterior by

using a section of cabinet or an

added layer of insulation.

➢ Refer to section in Use and Care

Guide on temperature controls for

recommended control settings.

➢ Clean door gaskets every three

months according to Use and Care

Guide instructions. This will assure

that door seals properly and

refrigerator runs efficiently.

➢ Take time to organize items in

refrigerator to reduce time that door

is open.

➢ Be sure your doors are closing

securely by leveling refrigerator as

instructed in your Use and Care

Guide.

➢ Clean condenser coils off as

indicated in the Use and Care Guide

every 3 months. This will increase

energy efficiency and cooling

performance.

To avoid personal injury or property

damage, observe the following:

➢ Allow light bulb to cool.

➢ Wear gloves when replacing light

bulb.

CAUTION

To avoid electrical shock which can

cause severe personal injury or

death, disconnect power to

refrigerator before replacing light

bulb. After replacing light bulb,

connect power.

WARNING

How to remove and

replace light bulbs

FRESH FOOD

1. Slide shield toward

back of

compartment to

release from light

assembly.

2. Remove light bulbs.

3. Replace with appliance bulbs

greater than 40 watts.

4. Replace light bulb

cover by inserting

tabs on light shield

into liner holes on

each side of light

assembly. Slide shield toward front of

refrigerator until it locks into place.

DO NOT force shield beyond locking

point. Doing so may damage light

shield.

FREEZER

1. Pinch rear tabs on

light cover and pull

straight down.

2. Remove light

bulb.

3. Replace bulb with appliance bulb

greater than 40 watts.

4. Insert front tabs of light cover into

freezer liner and snap rear portion

over light assembly until rear tabs

engage.

Normal operating sounds

Today’s refrigerators use foam insulation and are more energy efficient than refrigerators of the past. However, foam insulation is

not as sound absorbent as former insulated models. As a result, certain sounds may be unfamiliar. In time, these sounds will

become familiar. Please refer to this information before calling service.

SOLUTION

➢ Normal operation

➢ See Installing your Refrigerator for details on how to level

your refrigerator.

➢ Normal operation

➢ Stop sound by raising ice maker arm to ‘off’ position. See

Automatic Ice Maker section in your Use and Care Guide

for details.

➢ Normal operation

POSSIBLE CAUSE

➢ Freezer control (A) clicks when

starting or stopping compressor.

➢ Defrost timer (B) sounds like an

electric clock and snaps in and

out of defrost cycle.

➢ Freezer fan (C) and condenser

fan (D) make this noise while

operating.

➢ Evaporator (E) and heat

exchanger (F) refrigerant makes

this noise when flowing.

➢ Ice cubes from ice maker (select

models) drop into ice bucket (G).

➢ Compressor (H) makes a

pulsating sound while running.

➢ Refrigerator is not level.

➢ Ice maker water valve (I)

hookup (select models) buzzes

when ice maker fills with water.

➢ Ice maker (J) is in the ‘on’

position without water

connection.

➢ Compressor (H) can make a high-

pitched hum while operating.

➢ Defrost heater (K) hisses, sizzles

or pops when operational.

TOPIC

Clicking

Air rushing or whirring

Gurgling or boiling

sound

Thumping

Vibrating noise

Buzzing

Humming

Hissing or

popping

ENGLISH FRANÇAIS ESPAÑOL

PROBLEM

Food temperature

appears too warm

Refrigerator has an odor

Water droplets form on

outside of refrigerator

Water droplets form on

inside of refrigerator

Refrigerator or ice maker

make unfamiliar sounds

or seems too loud

Crisper drawers do not

close freely

Refrigerator runs too

frequently

Operation

POSSIBLE CAUSE

Door is not closing properly.

Controls need to be adjusted.

Condenser coils are dirty.

Rear air grille is blocked.

Door has been opened frequently, or has

been opened for long periods.

Food has recently been added.

Compartment is dirty or has odor-causing

food.

Check gaskets for proper seal.

Humidity levels are high.

Controls require adjustment.

Humidity levels are high or door has been

opened frequently.

Check gaskets for proper seal.

Normal operation.

Contents of drawer, or positioning of items in

the surrounding compartment could be

obstructing drawer.

Drawer is not in proper position.

Refrigerator is not level.

Drawer channels are dirty or need treatment.

Doors have been opened frequently or have

been opened for long periods of time.

Humidity or heat in surrounding area is high.

Food has recently been added.

Refrigerator is exposed to heat by

environment or by appliances nearby.

Condenser coils are dirty.

SOLUTION

See Installing Your Refrigerator–How to Level Your

Refrigerator

section on how to properly level refrigerator.

Check gaskets for proper seal. Clean, if necessary, according

to cleaning instructions.

Check for internal obstructions that are keeping door from

closing properly (i.e. improperly closed drawers, ice buckets,

oversized or improperly stored containers or foodstuffs, etc.)

See

Setting and Maintaining Proper Temperatures–

Adjusting the Controls

section on how to adjust your controls.

See section on

Hints and Care–How to Clean Your

Refrigerator

for instructions.

Check the positioning of food items in refrigerator to make

sure grille is not blocked. Rear air grilles are located under

crisper drawers.

Reduce time door is open. Organize food items efficiently to

assure door is open for as short a time as possible.

Allow interior environment to adjust for period the door has

been open.

Allow time for recently added food to reach refrigerator or

freezer temperature.

See section on

Hints and Care for instructions.

See section on

Hints and Care–How to Clean Your

Refrigerator

for instructions.

See

Setting and Maintaining Proper Temperatures–

Adjusting the Controls

section on how to adjust your controls.

See

Setting and Maintaining Proper Temperatures–

Adjusting the Controls

section on how to adjust your controls.

See

Setting and Maintaining Proper Temperatures–

Adjusting the Controls

section on how to adjust your controls.

Reduce time door is open. Organize food items efficiently to

assure door is open for as short a time as possible.

See section on

Hints and Care–How to Clean Your

Refrigerator

for instructions.

Refer to

Normal Operating Sounds.

Reposition food items and containers to avoid interference

with the drawers.

See section on

Fresh Food Features–Climate-Controlled

Drawers

to verify drawer positioning.

See

Installing Your Refrigerator–How to Level Your

Refrigerator

section on how to properly level refrigerator.

Clean drawer channels with warm, soapy water. Rinse and

dry thoroughly. Apply a thin layer of petroleum jelly to drawer

channels.

Reduce time door is open. Organize food items efficiently to

assure door is open for as short a time as possible.

Allow interior environment to adjust for period the door has

been open.

Normal operation.

Allow time for recently-added food to reach refrigerator or

freezer temperature.

Evaluate your refrigerator’s environment. Refrigerator may

need to be moved to run more efficiently.

See section on

Hints and Care–How to Clean Your

Refrigerator

for instructions.

Troubleshooting

Ice and water

PROBLEM

Refrigerator runs too

frequently

continued

POSSIBLE CAUSE

Controls need to be adjusted.

Door is not closing properly.

SOLUTION

See Setting and Maintaining Proper Temperatures–

Adjusting the Controls

section on how to adjust your controls.

See

Installing Your Refrigerator–How to Level Your

Refrigerator

section on how to properly level refrigerator.

Check gaskets for proper seal. Clean, if necessary. See section on

Hints and Care–How to Clean Your Refrigerator for instructions.

Check for internal obstructions that are keeping door from

closing properly (i.e. improperly closed drawers, ice buckets,

oversized or improperly stored containers or foodstuffs, etc.)

Operation, cont.

Refrigerator is leaking

water

Ice forms in inlet tube to

ice maker

Water flow is slower than

normal

Plastic tubing was used to complete water

connection.

Improper water valve was installed.

Water pressure is low.

Freezer temperature is too high.

Water pressure is low.

Improper water valve was installed.

Sears recommends using copper tubing for installation.

Plastic is less durable and can cause leakage.

Sears is not

responsible for property damage due to improper

installation or water connection.

See section on Installing Your Refrigerator–How to

Connect the Water Supply

for instructions. Self-piercing and

⁄16” saddle valves cause low water pressure and may clog the

line over time.

Sears is not responsible for property

damage due to improper installation or water connection.

Water pressure must be between 20 to 100 pounds per

square inch to function properly. A minimum pressure of

35 pounds per square inch is recommended for refrigerators

with water filters.

See

Setting and Maintaining Proper Temperatures–

Adjusting the Controls

section on how to adjust your

controls. Freezer is recommended to be between 0 to 2° F

(-18 to -17° C).

Water pressure must be between 20 to 100 pounds per

square inch to function properly. A minimum pressure of

35 pounds per square inch is recommended for refrigerators

with water filters.

See section on

Installing Your Refrigerator–How to

Connect the Water Supply

for instructions. Self-piercing and

⁄16” saddle valves cause low water pressure and may clog the

line over time.

Sears is not responsible for property

damage due to improper installation or water connection.

Troubleshooting, cont.

La page charge ...

Kenmore 593 . 66122700 Manuel utilisateur

Marque: Kenmore

Modèle: 593 . 66122700

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 593 . 66122700 User manual
español: Kenmore 593 . 66122700 Manual de usuario

Kenmore 593 . 66122700 Manuel utilisateur

Kenmore 593 . 66122700 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents