Monogram 1892728 Guide d'installation

INSTALLATION

INSTRUCTIONS

30” Integrated Bottom Freezer Refrigerator

30” Integrated Bottom Freezer Wine Reserve

ENGLISH/FRANÇAIS/ESPAÑOL.

MONOGRAM.COM

2

31-1000169 Rev. 4

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use. Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately

contact your dealer or builder.

Skill Level – Installation of this unit requires basic

mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the Monogram Warranty. See the Owner’s Manual for

warranty information.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping

forward which could result in death or serious injury. Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from appliance. Failure to do so can result

in fire, explosion, or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to

have access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance,

2 people are required for proper installation.

CAUTION

.HHSILQJHUVRXWRIWKH³SLQFKSRLQWƎDUHDVFOHDUDQFHVEHWZHHQWKHGRRUVDQGEHWZHHQWKH

doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord.

If the supply cord is damaged it must be replaced by a

qualified service professional with an authorized service

part from the manufacturer.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the unit.

This appliance must be installed with a means in the

fixed house wiring or circuit breaker for disconnecting the

appliance from the electrical supply after installation.

For Monogram local service in your area, visit monogram.com or call 800.444.1845.

For Monogram service in Canada, visit monogram.ca or call 800.561.3344.

For Monogram Parts and Accessories, visit monogram.com or call 800.444.1845.

For Monogram Parts and Accessories in Canada, visit monogram.ca or call 800.661.1616.

3

31-1000169 Rev. 4

Safety Information

Contents

WARNING

EXPLOSION HAZARD Flammable Refrigerant

This appliance contains isobutane refrigerant,

R600a, a natural gas with high environmental

compatibility. However, it is also combustible.

Adhere to the warnings below to reduce the risk of

injury or property damage.

1) When handling, installing and operating the appliance,

care should be taken to avoid damage to the

refrigerant tubing.

2) Service shall only be performed by authorized service

personnel. Use only manufacturer-authorized service

SDUWVƎ

3) Dispose of unit in accordance with Federal and Local

Regulations. Flammable refrigerant and insulation

material used require special disposal procedures.

Contact your local authorities for the environmentally

safe disposal of your unit.

4) Keep ventilation openings in the appliance enclosures

or in the built-in structure clear of obstruction.

5) Do not use mechanical devices or other means to

accelerate the defrosting process.

6) Do not damage refrigerant circuit.

7) Do not use electrical appliances inside the food

storage compartment of the appliance.

Design Guide

Cabinet Enclosure Dimensions for

Fully Integrated Instructions 4

Unit Dimensions with 3/4” Panels 5

Cabinet Enclosure Dimensions for

Single or Multiple Units 6

The Installation Space (per unit) 7

Grounding the Unit 7

115° Door Swing 8

90° Door Swing 9

SS Panel Accessory & Dimensions 10

ƎFP&XVWRP3DQHO'LPHQVLRQV 

Installation Instructions for Single Unit

Tools, Hardware, Materials 12

Step 1. Remove Packaging 13

Step 2. Install Anti-tip Bracket 14

Step 3. Connect Water Line 14

Step 4. Connect Power 14

Step 5. Slide Unit into Enclosure 15

Step 6. Remove Toekick and Vent 15

Step 7. Level Unit 15

Step 8. Install Toekick and Vent 16

Step 9. Reverse Door Swing 16

Step 10. Adjust Door Swing 17

Step 11. Install Door Bracket Covers 17

Step 12. Install Door and Drawer Panels 18

Step 13. Start Icemaker 19

Installation Instructions for Multiple Units

Tools, Hardware, Materials 20

Step 1. Remove Packaging 21

Step 2. Install Heater Unification Kit(S) to Unit 2 22

Step 3. Reverse Door Swing (Unit 1) 24

Step 4. Adjust Door Swing (Unit 1) 26

Step 5. Install Door Bracket Covers (Unit 1) 26

Step 6. Installing Other Units 26

Step 7. Join Units 26

Step 8. Install Anti-Tip Brackets 27

Step 9. Connect Water Line 27

Step 10. Connect Power 27

Step 11. Slide Units into Enclosures 28

Step 12. Install Hinge Guard 28

Step 13. Connect Heater 28

Step 14. Level Units 29

Step 15. Install Toekick And Vent 30

Step 16. Install Front Trim 30

Step 17. Install Door and Drawer Panels 31

Step 18. Start Icemaker 32

4

31-1000169 Rev. 4

Design Guide (One Unit)

Cabinet Enclosure Dimensions For Fully Integrated Instructions

Height options

80" (203.2 cm)

or *84" (213.4 cm)

30" Finished Width

(76.2 cm)

25" min. depth

(63.5 cm)

7KHFXWRXWGHSWKPXVWEHƎIRU

flush installations.

• The front face of the unit fits flush

ZLWKƎFPGHSWKDGMDFHQW

cabinets.

7KHXQLWFDQILWLQWRDƎ

FPPLQLPXPƎFP

maximum high enclosure. The unit

LWVHOIFDQRQO\EHUDLVHGWRƎ

(204.2 cm).

• The refrigerator door panel can be

FRQVWUXFWHGWRILOODGGLWLRQDOKHLJKW

see Stainless Steel or Custom

Panel sections.

'HVLJQ7LS:HUHFRPPHQGILQLVKLQJWKHLQVLGHVXUIDFHRIWKHHQFORVXUHDPLQRIƎFPIURPWKH

front face.

'HVLJQ7LS,IXVLQJƎFPHQFORVXUHFRQVLGHUDGGLQJDILQLVKHGYDOHQFHDERYHWKHXQLWFDVH

34 3/8"

(87.3 cm)

34 3/8"

(87.3 cm)

Design Tip: It is possible to align your unit drawer with adjacent cabinetry for a completely integrated

look.

5

31-1000169 Rev. 4

Design Guide

Height adjustable

from

79-3/8” to 80-3/8” *

(201.6 cm - 204.2 cm)

23-3/4"

(60.3 cm)

29-3/4"

(75.6 cm)

1-1/4"

(3.2 cm)

3/4"

(19.1 mm)

1/8"

(3.2 mm)

4"

(10.2 cm)

6"

(15.2 cm)

Case

Door

Panel

Clearance

Front with Panels Side with Panels

8QLW'LPHQVLRQVZLWKƎ3DQHOV

Top with Panels

Install Clearances

Top

ƎPP

Each Side

ƎPP

Rear

ƎPP

7KH8QLWFDQEHDGMXVWHGWRILWLQWRDFDELQHWVSDFHWKDWLVƎFPWRƎ

(214.3 cm) with the appropriate door panel kit.

(Case and Door only)

6

31-1000169 Rev. 4

Design Guide

Cabinet Enclosure Dimensions for Single or Multiple Units

77”

(195.5 cm)

Hinge Side

Anti Tip Location - DO NOT

obstruct this area.

Electrical and Water

Area Connection

6” (15.2 cm)

Electrical Outlet and

Home Water Source

1 per product

E = 5” (12.4 cm) x 6” (15.2 cm)

W = 6.25” (15.87 cm) x 6” (15.2 cm)

30” (76.2 cm)

4-3/8”

(11 cm)

25”

(63.5 cm)

Product

Depth

Opening

Height

80”

(203.2 cm)

min.

84”

(213.4 cm)

max.

77”

(195.5 cm)

E

W

ONE PRODUCT INSTALLATION

TWO PRODUCTS INSTALLATION

77”

(195.5 cm)

Hinge Side

Electrical and Water

Area Connection

6” (15.2 cm)

25”

(63.5 cm)

Product

Depth

Anti Tip Location - DO NOT

obstruct this area.

60” (152.4 cm)

Opening

Height

80”

(203.2 cm)

min.

84”

(213.4 cm)

max.

4-3/8”

(11 cm)

E

W

E

W

34-1/8”

(86.7 cm)

77”

(195.5 cm)

Electrical Outlet and

Home Water Source

1 per product

E = 5” (12.4 cm) x 6” (15.2 cm)

W = 6.25” (15.87 cm) x 6” (15.2 cm)

THREE PRODUCTS INSTALLATION

25”

(63.5 cm)

Product

Depth

Electrical Outlet and Home Water Source

1 per product

E = 5” (12.4 cm) x 6” (15.2 cm)

W = 6.25” (15.87 cm) x 6” (15.2 cm)

90” (228.6 cm)

Anti Tip Location - DO NOT

obstruct this area.

Electrical and Water

Area Connection

6” (15.2 cm)

Opening

Height

80”

(203.2 cm)

min.

84”

(213.4 cm)

max.

77”

(195.5 cm)

4-3/8”

(11 cm)

E

W

E

W

E

W

34-1/8”

(86.7 cm)

64”

(86.7 cm)

Hinge Side

NOTES:

• When two or three units are installed side

by side, an exterior heater must be applied

to the left exterior wall of the second and/

RUWKLUGXQLW6HH([WHULRU+HDWHU8QL¿FDWLRQ

Kit.

• Toekick dimension is 4” (10.2 cm) from the

ÀRRU

•7KHSURGXFWFDQ¿WLQWRD´

cm) minimum and up to 84 1/2” (214.6 cm)

maximum high enclosure.

• The unit can only be raised to 80-3/8”

(204.2 cm).

• The unit door panel can be constructed to

¿OODGGLWLRQDOKHLJKW6HHGRRUDGMXVWPHQW

section.

25

SIDE VIEW

25" (63.5)

3 1/2"

(8.9)

Finished

Return

Back

127(&RQ¿JXUDWLRQVZLWKXQLWVLQVWDOOHGKLQJHWRKDQGOH

will result in interference while opening doors. To enable

all three doors to open independently, additional clearance

between the hinge to handle units is required and the

middle door should be set to a 90 degree opening.

7

31-1000169 Rev. 4

Design Guide (One, Two, or Three Units)

THE INSTALLATION SPACE (Per Unit)

Water and Electrical Locations

Locate electrical and water supply connections in the areas shown on the Cabinet Dimensions section page.

WARNING

Connect to potable water supply only.

PREPARING INSTALL WATER LINE

• A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120

p.s.i. (275-827 kPa).

5RXWHƎFP2'FRSSHURU6PDUW&RQQHFW

™

plastic tubing between the house cold water line and the water

connection location.

• Tubing should be long enough to extend to the front of the enclosure.

• Water line can enter an opening through the floor or back wall.

• Install a shut-off valve between the icemaker water valve and cold water supply in the home.

NOTE:

• It is recommended that the water shut-off valve be placed in a location that is easily accessible. We do not advise

placing it behind the unit because of access difficulties. If it is necessary to install the valve behind the unit, it must

be located in the area shown on Design Guide.

• Saddle type shut-off valves are included in many water supply kits, but are not recommended for this application.

• The only GEA-approved plastic tubing is supplied in the SmartConnect

™

Refrigerator Tubing kits. Do not use any

other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or

rupture with age and cause water damage to your home. See water line kits on Assessories Page.

• Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use

is not permitted in Massachusetts. Consult with your licensed plumber.

Electrical Specifications

• A 115-volt, 60-Hz., 15- or 20-amp power supply is required. An individual properly grounded branch circuit or circuit

breaker is recommended.

• Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on

rear wall as shown in the Cabinet Dimensions section.

NOTE: GFI (ground fault interrupter) is not recommended.

GROUNDING THE UNIT

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

three-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT

OR REMOVE THE THIRD

(GROUND) PRONG FROM

THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT THE

UNIT TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

WARNING

Electrical Shock

Hazard.

Failure to follow these instructions can

result in death, fire, or electrical shock.

8

31-1000169 Rev. 4

Design Guide (One, Two, or Three Units)

1-1/2" (3.8 cm)

1-1/4" (3.2 cm)

1" (2.5 cm)

3/4" (1.9 cm)

1-1/2"

(3.8 cm)

2-1/16" (5.4 cm)

1-1/4"

(3.2 cm)

1-3/8"

(3.5 cm)

1"

(2.5 cm)

3/4"

(1.9 cm)

1/8" (3.2 mm)

Allow 17" (43.2 cm) minimum

clearance to a wall for a full

115° door swing.

Refrigerator

Stainless Steel or Custom Panels

Top View

115° DOOR SWING

(factory setting)

Product Clearances

These units are equipped with a 2-position door stop. The

factory-set 115° door swing can be adjusted to 90° if clear-

ance to adjacent cabinets or walls is restricted.

For 90° Door swing see next page.

Not to scale

TOP VIEW

DIMENSIONS BASED

ON HANDLE HEIGHT

OF 2-9/16” (6.5)

DOOR OPEN 115°

29 1/4”

(74.3 cm)

29 15/16”

(76.0 cm)

16-9/16"

(42.1 cm)

Minimum

to a Wall

9

31-1000169 Rev. 4

Design Guide (One, Two, or Three Units)

For a 90º door swing

allow 4" (10.2 cm)

min. clearance to a

wall, for stainless

steel models.

1-1/2"

(3.8 cm)

2-1/4"

(5.7 cm)

1-1/4"

(3.2 cm)

1"

(2.5 cm)

3/4"

(1.9 cm)

1-1/2" (3.8 cm)

1-1/4" (3.2 cm)

1-3/16"

(3 cm)

1" (2.5 cm)

3/4" (1.9 cm)

Refrigerator

1/8" (3.2 mm)

Stainless Steel or Custom Panels

Top View

90° DOOR SWING

(optional setting)

Not to scale

TOP VIEW

DOOR OPEN 90°

DIMENSIONS BASED

ON HANDLE HEIGHT

OF 2-9/16” (6.5)

33 1/4”

(84.5 cm)

29 1/4”

(74.3 cm)

5-1/8"

(13.0 cm)

Minimum

to a Wall

10

31-1000169 Rev. 4

Design Guide (One, Two, or Three Units)

SS PANEL ACCESSORY & DIMENSIONS

ƎFP7KLFN6ROLG'RRU3DQHO2SWLRQVDQGƎFP7KLFN)UDPHIRU*ODVV'RRU

(75.6 cm)

29-3/4"

4" (10.2 cm)

7-9/16"

(19.2 cm)

22-3/4"

(57.8 cm)

1/8" (3.2 mm) Min.*

Fresh

Food

Ice Drawer

Cabinets

Freezer/

Convertible

Drawer

45-3/8" (115.3 cm) for

80" (203.2 cm) Installation

49-3/8" (125.4 cm) for

84" (213.4 cm) Installation

(75.6 cm)

29-3/4"

23"

(58.4 cm)

Glass Panel

for Fresh Food

45-3/8"

(115.3 cm)

49-3/8"

3-3/8"

(8.6 cm)

6"

(15.2 cm)

6"

(15.2 cm)

80"

(203.2 cm)

Install.

10"

(25.4 cm)

84"

(213.4 cm)

Install.

ACCESSORIES/KITS

Kit Name Instruction PN

+HDWHU8QL¿FDWLRQ.LW ZUG30

Water Line 8’ (2.5m) WX08X10006

Water Line 15’ (4.6m) WX08X10015

Water Line 25’ (7.6m) WX08X10025

Stainless Steel Full Door and Drawer Panel Kits (Order for a Full Product)

NOTE: Each kit also contains matching top door, freezer and customizable

drawer panels, and toe kick.

FULL DOOR & DRAWER KIT ATTRIBUTES/REQUIREMENTS

Instructions PNDoor Front Type: Door Height Left or Right

Glass 80” Left ZKGSN809NLH

Glass 80” Right ZKGSN804NRH

Glass 84” Left ZKGSN849NLH

Glass 84” Right ZKGSN844NRH

Solid 80” Left ZKSSN809NLH

Solid 80” Right ZKSSN804NRH

Solid 84” Left ZKSSN849NLH

Solid 84” Right ZKSSN844NRH

Handles and Mountings Instructions PN

Minimalist Handle Full Kit ZKGC3H3CNSS

Minimalist Door Handle WR12X32600

Minimalist Handle (Drawer) WR12X32406

Statement Handle Full Kit ZKGC3H3PNSS

Statement Door Handle WR1232571

Statement Freezer Handle WR12X32599

Custom Panel Handle Stud Kit ZKPN

11

31-1000169 Rev. 4

Design Guide (One, Two, or Three Units)

3/4ƎFP&867203$1(/',0(16,216ƎFP+LJK)XOO\

Integrated Installation

ƎFP&867203$1(/',0(16,216ƎFP+LJK)XOO\

Integrated Installation

If you choose to install custom panels, they must be cut

to the dimensions shown. The panels will attach to the

door and drawers using a hook and bracket system.

EXTREMELY IMPORTANT: Custom wood panels

PXVWEHDWOHDVWƎFPWKLFNZKHUHKRRNVDQG

bracket hardware are attached. Refer to Templates

for hook and bracket location.

NOTE:7KLVSURGXFWLVGHVLJQHGWRKDQGOHƎFP

panels that are made of wood.

Ǝ[Ǝ[FPLVWKHPD[LPXP

opening for a glass window. The opening may be

smaller if desired.

If you choose to install custom panels, they must be cut

to the dimensions shown. The panels will attach to the

door and drawers using a hook and bracket system.

EXTREMELY IMPORTANT: Custom wood panels

PXVWEHDWOHDVWƎFPWKLFNZKHUHKRRNVDQG

bracket hardware are attached. Refer to Templates

for hook and bracket location.

NOTE:7KLVSURGXFWLVGHVLJQHGWRKDQGOHƎFP

panels that are made of wood.

Ǝ[Ǝ[FPLVWKHPD[LPXP

opening for a glass window. The opening may be

smaller if desired.

IMPORTANT NOTE: Maximum panel weight:

A Refrigerator Door Panel: 33 lbs.

B Freezer Drawer Panel: 9 lbs.

C Convertible Drawer Panel: 19 lbs.

IMPORTANT NOTE: Maximum panel weight:

A Refrigerator Door Panel: 33 lbs.

B Freezer Drawer Panel: 9 lbs.

C Convertible Drawer Panel: 19 lbs.

29-3/4”

(75.6 cm)

33-3/8”

(84.8 cm)

3-3/8”

(8.6 cm)

6”

(15.2 cm)

6”

(15.2 cm)

3-3/8”

(8.6 cm)

23”

(58.4 cm)

45-3/8”

(115.3 cm)

A

B

C

(115.3 cm)

45-3/8

"

(75.6 cm)

29-3/4"

7-9/16

"

(19.2 cm)

22-3/4

"

(57.8 cm)

(10.7 cm)

4

"

PANELS FOR SOLID DOOR

AND DRAWERS

PANELS FOR SOLID DOOR

AND DRAWERS

PANELS FOR

GLASS DOOR

PANELS FOR

GLASS DOOR

6W\OHVPXVWEHDPLQƎFPWR

cover aluminum door frame.

6W\OHVPXVWEHDPLQƎFPWR

cover aluminum door frame.

Design Tip: Some amount of each panel will be visible on the interior side

of the unit. It is recommended that both sides of each panel be finished.

Design Tip: If using custom panels, a custom toe kick should

be considered. The Bottom of case is white.

Design Tip: Some amount of each panel will

be visible on the interior side of the unit. It is

recommended that both sides of each panel

be finished.

Design Tip: If using custom panels, a custom

toe kick should be considered. The Bottom of

case is white.

29-3/4”

(75.6 cm)

33-3/8”

(84.8 cm)

3-3/8”

(8.6 cm)

10”

(25.4 cm)

6”

(15.2 cm)

3-3/8”

(8.6 cm)

23”

(58.4 cm)

45-3/8”

(115.3 cm)

A

B

C

(115.3 cm)

45-3/8

"

(75.6 cm)

29-3/4"

7-9/16

"

(19.2 cm)

22-3/4

"

(57.8 cm)

(10.7 cm)

4

"

12

31-1000169 Rev. 4

Installation Instructions

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT

TOOLS REQUIRED

Ǝ$OOHQZUHQFK

• Utility knife

• Stepladder

• Bucket

• Level

• Appliance hand truck

• Tubing cutter

ƎRSHQHQGZUHQFK

ƎRSHQHQGZUHQFK

• #2 Phillips screwdriver

• Drill and bit set

ƎVRFNHW

• Safety glasses

• Pliers

ƎUDWFKHW

• Torx T-20, T-30 wrench

HARDWARE SUPPLIED

• Anti-tip bracket & screws

• Panel installation kit

• Door panel templates- Pub # 31-1000149, 31-1000150,

31-1000151, 31-1000152

• Water filter - Part # XWFE

• Drywall Anchors and screws

MATERIALS REQUIRED

ƎFRSSHUZDWHUOLQHWXELQJRU6PDUW&RQQHFW

Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for refrigerator door, freezer drawer and

Convertible drawer

• Velcro w/adhesive if using custom toekick.

FLOORING

For proper installation, this unit must be placed on a level

surface of hard material that is at the same height as the

rest of the flooring. This surface should be strong enough

to support a fully loaded unit, or approximately 1,200 lbs.

NOTE: Protect the finish of the flooring. Cut a large sec-

tion of the cardboard carton and place under the unit

where you are working.

UNIT LOCATION

Ŷ Do not install the unit where the temperature will go

below 60°F (16°C). It will not run often enough to

maintain proper temperatures.

Ŷ Do not install the unit where temperatures will go above

100°F (37°C). It will not perform properly.

Ŷ Do not install the unit in a location exposed to water

(rain, etc.) or direct sunlight.

Ŷ Do not install the unit on a floor not strong enough to

support it fully loaded.

13

31-1000169 Rev. 4

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

This appliance is top heavy. Use extreme caution

with moving to prevent tipping over which could

result in death or serious injury.

Ŷ Cut bands and tape on the top and bottom

of packaging with a utility knife.

Ŷ Unfold the cardboard seams and remove the top

of the packaging.

Ŷ Slide the remainder of the box off of the appliance. You

can use a box cutter to cut the remaining cardboard

being VERY CAREFUL not to scratch

the appliance.

Ŷ Remove the EPS supports from around the unit.

Ŷ DO NOT remove the door band or lower EPS banded

parts until unit is ready to go into enclosure.

Ŷ Remove anti-tip bracket and foam blanket from top of

unit and set aside for installation later.

Ŷ Keep front door band and door/drawer tape on unit

until product is installed to anti-tip bracket.

Ŷ Remove trim pieces taped to front of product and set

aside for installation later.

Ŷ Remove all packing tape except for warning labels and

tape with orange warning labels.

Ŷ Pull back, but DO NOT REMOVE, door/drawer tape.

Ŷ Open middle drawer and remove Owner’s Manual

packet which includes unit installation instructions.

Ŷ Close middle drawer and re-apply tape to keep the

door and drawers closed until product is installed to

anti-tip bracket.

Ŷ Cut EPS skid at the sides near the front from the back

of the unit.

Ŷ Push unit forward & remove rear portion of the EPS

skid.

Ŷ Carefully lower rear onto the floor.

Ŷ Lean unit back slightly & remove front portion of the

EPS skid.

Ŷ Discard all unused packaging materials appropriately.

Ŷ The unit can now be moved using an appliance hand

truck or rolled on a properly protected floor by 2

people.

Ŷ Leave any protective film on the unit until installation is

complete.

Installation Instructions

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT

14

31-1000169 Rev. 4

STEP 3 CONNECT WATER LINE

WARNING

Connect to potable water supply

only.

Ŷ Position appliance in front of enclosure.

Ŷ Locate and bring tubing to the front of the cabinet.

Ŷ Turn the water on to flush debris from line. Run about

DTXDUWRIZDWHUWKURXJKWXELQJLQWRDEXFNHWWKHQ

shut off water.

If needed cut the tubing to the proper length so it can

be attached to the water valve.

Copper Tubing:

Ŷ 6OLSDƎQXWDQGIHUUXOHRYHUERWKHQGVRIWKH

copper tubing. Insert tube into the union fitting on the

unit and tighten nut to union.

Ŷ Turn on the water to check for leaks.

SmartConnect™ Tubing:

ŶFollow the instructions provided with the tubing. Over

tightening may cause leaks. Turn on the water to

check for leaks.

NOTE: Coil excess tubing length behind the unit.

Installation Instructions

67(3,167$//$17,7,3

BRACKET

Ŷ,QVLGHWRSIDFHRIEUDFNHWVKRXOGEHLQVWDOOHGDWƎ

FP³6ORWƎLQEUDFNHWVKRXOGWREHSODFHGLQ

FHQWHURILQVWDOOVSDFHW\SLFDOO\Ǝ>FP@

Ŷ Mark (within slots, placement) stud and anchor

positions on brackets.

Ŷ Secure bracket using a combination of studs &

anchors.

Ŷ At least 1 stud must be engaged. However, please

engage as many studs as possible within the

enclosure. A minimum of three fasteners should be

used for proper installation.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

Water

Line Hole

STEP 4 CONNECT POWER

Ŷ Plug the power cord into the socket.

Ŷ Check to make sure power to unit is on by opening

the ice drawer (FF door will be banded or taped shut)

to see if interior lights are on.

Ŷ The temperature controls are preset at 37°F for the

refrigerator section and 0°F in both the freezer drawer

and customizable drawer.

Ŷ Allow 24 hours to stabilize before making

adjustments.

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT (cont.)

Slot

80”

ƎFP

15

31-1000169 Rev. 4

STEP 5 SLIDE UNIT INTO

ENCLOSURE

Roll the unit into the enclosure, being careful not to

pinch the water line or power cord.

Ŷ$ORQJIODWEDURU\DUGVWLFNPD\EHQHHGHGWRJXLGH

the front edge of the anti-tip bracket over the unit.

ŶIf space allows, you may also bend the front edge of

the bracket upward slightly, allowing it to clear the

back of the unit.

ŶRemove top-center trim cover from unit.

ŶSecure the unit to the Anti-tip bracket using both

machine screws & washers to engage the threaded

inserts in the anti-tip bracket.

ŶHand start the screws until unit is in desired location

within the install space.

ŶFinalize unit install by tightening the screws fully.

ŶReinstall Trim cover.

STEP 7 LEVEL UNIT

All models have 4-point leveling. The front is supported

E\OHYHOLQJOHJVWKHUHDULVVXSSRUWHGE\DGMXVWDEOH

wheels. Both are accessible from the front of the unit.

Ŷ7ROHYHOWKHEDFNRIWKHXQLWWXUQWKHƎKH[

nut located above the front wheels. Turn counter

clockwise to raise or clockwise to lower the unit.

Ŷ)RUIURQWOHYHOLQJXVHDƎRSHQHQGZUHQFK

ŶAdjust height of unit to match installation cutout

opening. The unit should be level and plumb with

cabinetry.

NOTICE: The rear leveling wheels and front leveling

OHJVDUHOLPLWHGWRDPD[LPXPKHLJKWDGMXVWPHQWRIƎ

,IWKHLQVWDOODWLRQUHTXLUHVPRUHWKDQƎKHLJKWWKH

installer should elevate the unit on a sheet of plywood

or runners. Cabinetry trim could also be added across

the top of the opening to shorten the opening.

,I\RXDWWHPSWWRUDLVHWKHXQLWPRUHWKDQƎ\RXZLOO

damage the front leveling legs and the rear leveling

wheels.

Installation Instructions

STEP 6 REMOVE TOEKICK AND

VENT

The toekick must be removed to access the leveling

leg system.

ŶRemove band around EPS block in front of toekick.

ŶRemove and dispose of EPS block.

ŶRemove the solid portion of the toekick by pulling

forward.

Ŷ Place the toekick, vent and screws out of the way so

you will have them for reinstallation.

Vent

Screw

Toekick

Vent

Screws

(behind

toekick)

Screw

Up

Leveling Leg

Up

Hex Nut Adjusts

Rear Wheels

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT (cont.)

16

31-1000169 Rev. 4

STEP 9 REVERSE DOOR SWING

(if needed) (cont.)

8VLQJDƎ$OOHQZUHQFKUHPRYHWKHVFUHZV

per hinge that secure the door to the unit. Have

someone hold the door while removing these screws

to keep the door from falling.

2SHQWKHKLQJHV8VLQJDƎ$OOHQZUHQFK

remove the 2 screws per hinge that secure the hinge

to the unit cabinet.

5. Remove the trim and hinge pocket from the top of

the unit and install on the opposite sides.

6. Remove the trim and hinge pocket from the bottom

of the refrigerator compartment. Remove the control

panel and gently place in the FZ drawer.

7. Reinstall the control panel.

8. The hinges will be reinstalled in opposite corners.

The hinge from the top will be turned over

and installed at the bottom of the refrigerator

compartment. The hinge from the bottom will be

turned over and installed at the top of the refrigerator

compartment.

9. Install the screws on the refrigerator compartment

cabinet in all 4 places. Screw them in about halfway.

Installation Instructions

STEP 8 INSTALL TOEKICK AND

VENT

ŶLocate the toekick, vent and screws (removed

earlier).

ŶA custom toekick can be installed to match or

complement the surrounding cabinetry. Use the

supplied toekick as a template.

ŶReinstall the vent using the screws removed earlier.

ŶReinstall the toekick .

Supplied Toekick

Vent Holes

STEP 9 REVERSE DOOR SWING

(if needed)

Skip this step if door swing is satisfactory.

WARNING

Follow all steps when reversing

the door swing. Failure to follow these instructions,

leaving off parts, or overtightening screws, can

lead to the door falling off and result in injury and

property damage.

1. Remove the front tape from unit.

WARNING

Door Hinge Pinch

Point Hazard

This next step is important for safe handling of an

unloaded hinge. Do not skip step 2.

2. Release the hinge springs by using a Torx T-20

wrench to loosen the Torx screw from | to 0 on both

hinges. Close the door.

Top Hinge Bottom Hinge

Slots for

Tabs

Screws

Control Panel

Screws

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT (cont.)

17

31-1000169 Rev. 4

Installation Instructions

Screws

STEP 9 REVERSE DOOR SWING

(cont).

10. To install the top hinge, turn the hinge in the proper

direction—the section of the bracket that will be

attached to the door should be at the bottom of the

hinge. Slide the hinge over the screws and seat the

tabs into the hinge pocket. Tighten the screws.

11. To install the bottom hinge, turn the hinge in the

proper direction—the section of the bracket that will

attach to the door should be at the top of the hinge.

Slide the hinge over the screws and seat the tabs

into the hinge pocket. Tighten the screws. Close the

hinge.

12. Remove the hinge brackets from the door and rein-

stall them on the opposite end, top and bottom.

13. With another person holding the door in place, align

the holes in the door hinge bracket with the holes in

the hinge. Install the screws to the top hinge first.

14. Install screws on the bottom hinge next.

15. Using a Torx T-20

wrench, tighten the

tension on the hinge

springs by turning

the screws from 0

to |.

STEP 10 ADJUST DOOR SWING

(if needed)

NOTE: This unit has a 2-position door stop. When

space does not allow the door to swing to 115°, you

may limit the door swing to a 90°

Skip this step if door opening is satisfactory for your

installation situation.

Ŷ2SHQWKHUHIULJHUDWRUGRRUWRDFFHVVWKHWRSDQG

bottom hinges.

Ŷ/RRVHQWKHERWWRPKLQJHVFUHZVWKDWDWWDFKHGWRWKH

unit

Ŷ3XOOKLQJHIRUZDUGVOLJKWO\LQVHUWKLQJHSLQLQWRWKH

hole nearest the unit.

Ŷ<RXPD\QHHGWRXVHDVPDOOKDPPHUWRIXOO\VHDW

them in place.

Ŷ5HWLJKWHQKLQJHVFUHZV

ŶRepeat for top hinge.

STEP 11 INSTALL DOOR BRACKET

COVERS

Install covers to hide the brackets near the hinges on

the top and bottom of the door. The covers snap in

place.

Door

Screws

Use Torx

T-20 Wrench

Install 1 pin,

per hinge for 90°

door stop.

Hinge screws

Door Bracket

Cover

Hinge

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT (cont.)

18

31-1000169 Rev. 4

Installation Instructions

STEP 12 INSTALL DOOR AND DRAWER PANELS

1. Remove all door and drawer panel hardware and trim

from the unit.

2. Attach A1 - F1 brackets to the door panels in the

locations identified below. Custom panels must have

pre-drilled holes as shown in Door Panel Templates:

31-1000149, 31-1000150, 31-1000151, 31-1000152.

If you purchased an SS Panel Accessory, use the

Phillips machine screws to attach the brackets to the

SS door panels. For custom panels, use an appropriate

wood screw.

3. If you had custom handles made and they are not

currently attached to your panels, do so now.

4. Remove the screw caps from the adjustment pins on

the doors.

5. Open the refrigerator door to attach the refrigerator

panel.

6. Rest the refrigerator panel on the refrigerator door

by aligning the hooks on the panel brackets with the

adjustment pins on the door.

7. Fasten the panel to the refrigerator door in four

locations using the hardware shown below. Do not

tighten the screws. Screws will be tightened after panel

alignment.

8. Shift the panel side to side to ensure even gaps with

the adjacent cabinetry on both sides.

9. Use an allen wrench to

adjust the refrigerator

door panel depth

and height to align

with the adjacent

cabinetry. There must

be a minimum 1/8” gap

between the panel and

the adjacent cabinetry.

Item Quantity

Panel Brackets 12

Phillips Machine

Screws (for use

with SS Panel

Accessory)

34

Allen Hex Socket

Head Screws

12

Washers 12

Door Trim 6

Trim Caps 12

Allen Wrench 2

D1

A1

E1

F1

B1

C1

G1

Refrigerator

Panel

Customizable

Panel

Back View of Panels

Freezer

Panel

Do not tighten the screws, you will

do that after assembly process

and left to right alignment.

Align at top

and bottom

Screw and

Washer

Depth Adjustment

Vertical

Adjustment

Tighten one screw per bracket.

The other screws will be

tightened at the end of the

alignment process.

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT (cont.)

19

31-1000169 Rev. 4

Installation Instructions

STEP 13 START ICEMAKER

Ŷ Press the zone indicator on the control pad twice

to select the freezer drawer. Press the ICE icon on

the right side of the control. A line will appear under

ICE to show that the icemaker is ON.

Ŷ Be sure nothing interferes with the sweep of the

feeler arm.

Ŷ Discard the first full bucket of ice cubes.

Ŷ To turn the icemaker off, press the ICE icon. The

word OFF appears below ICE to show that the

icemaker is OFF.

STEP 12 INSTALL DOOR AND

DRAWER PANELS

(cont.)

10. Repeat steps 5-9 for the freezer drawer.

11. Repeat steps 5-9 for the customizable drawer.

12. Tighten all screws once you are satisfied with the

panel alignment.

13. Slide on trim to hide the panel adjustment hardware.

14. Add trim caps to cover the ends of the trim.

Trim

R

L

Align trim with bracket

INSTALLATION INSTRUCTIONS FOR SINGLE UNIT (cont.)

20

31-1000169 Rev. 4

Installation Instructions

INSTALLATION INSTRUCTIONS FOR MULTIPLE UNITS

TOOLS REQUIRED

Ǝ$OOHQZUHQFK

• Utility knife

• Stepladder

• Bucket

• Level

• Appliance hand truck

• Tubing cutter

ƎRSHQHQGZUHQFK

ƎRSHQHQGZUHQFK

• #2 Phillips screwdriver

• Drill and bit set

ƎVRFNHW

• Safety glasses

• Pliers

ƎUDWFKHW

• Torx T-20, T-30 wrench

HARDWARE SUPPLIED PER UNIT

• Anti-tip bracket & screws

• Panel installation kit

• Door panel templates- Pub # 31-1000149, 31-1000150,

31-1000151, 31-1000152

• Water filter - Part # XWFE

• Drywall Anchors and screws

MATERIALS REQUIRED PER UNIT

ƎFRSSHUZDWHUOLQHWXELQJRU6PDUW&RQQHFW

Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for refrigerator door, freezer drawer and

Convertible drawer

• Velcro w/adhesive if using custom toekick.

• ZUG30 Heater Unification Kit (1 Kit needed for each

additional unit.)

FLOORING

For proper installation, this unit must be placed on a level

surface of hard material that is at the same height as the

rest of the flooring. This surface should be strong enough

to support a fully loaded unit, or approximately 1,200 lbs.

NOTE: Protect the finish of the flooring. Cut a large sec-

tion of the cardboard carton and place under the unit

where you are working.

UNIT LOCATIONS

Ŷ Do not install the units where the temperature will go

below 60°F (16°C). They will not run often enough to

maintain proper temperatures.

Ŷ Do not install the units where temperatures will go

above 100°F (37°C). They will not perform properly.

Ŷ Do not install the units in a location exposed to water

(rain, etc.) or direct sunlight.

Ŷ Do not install units on a floor not strong enough to

support them fully loaded.

La page charge ...

Monogram 1892728 Guide d'installation

Monogram 1892728 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents