Vestfrost MK 304 Instructions For Use Manual

Ice-lined Refrigerator Model MK 304

+43ºC

+5ºC

+43ºC

+5ºC

GB Instructions for use

FR Consignes d’utilisation

ES Instrucciones para el uso



CHI 使用说明



General Information

The MK-Model is an ice-lined vaccine

refrigerator. It has one compartment for

vaccine storage (+2 to +8°C) equipped with

baskets.

Power supply

The MK 304 is equipped with a heavy-duty

compressor that can operate at voltages

22% below nominal voltage. See the rating

plate. If voltage variations go beyond

this range, it is recommended to use an

automatic voltage stabilizer.

Technical data

See the rating plate, which is placed at the

rear side of the appliance.

Unpacking and installation

Unpacking

1. Unpack the appliance and check that it

has not been damaged. If you observe any

damage, inform your supervisor.

2. Check the rating for correct voltage and



3. Open and remove all internal packing

material.

Contents

General information ....................................2

Power supply ..............................................2

Technical data.............................................2

Unpacking...................................................2

Get to know your refrigerator ......................3

Installation ..................................................4

Electrical connection...................................5

Operation and function ...............................6

Cool down of the appliance ........................6

Loading the appliance ................................

Maintenance and cleaning..........................8

Trouble shooting .........................................9

Warranty, Spare parts and service ...........10

Wiring diagram .........................................13

Disposal ...................................................14



without prior notice.

2

GB

Get to know your Refrigerator

Handle

Sealing strip

Vaccine storage

Water ballast box

Compressor compartment

with ventilation grille

Temperature display

Fig. 1

3

GB

Location

The appliance must be placed in a well

ventilated room, not in direct sunlight and

away from other heating sources.

When installing the appliance please





Installation

800 mm

50 mm

100 mm

There must be at least 30 mm clearance

between the base of the appliance and the



There must be free access to



Fig. 2

Fig. 3

4

GB

Preparation



-



earthed.

Colour code for leads:

Lead of cord Pin of plug

230 V 115 V

Brown White Live

Blue Black Neutral

Green/Yellow Green Earth

Connect the plug to the socket and switch

on the appliance.

- Check, by listening, that the compressor is

running, if it does not run, contact your

supervisor.

Electrical connection

5

GB

Operation and function

Electronic thermostat

The appliance has an electronic thermostat

that controls the temperature in the vaccine

compartment. The thermostat is set by the

factory

1. The green lamp is on when the appliance

is connected to the power supply.

2. Thermometer.

Starting procedure

Connect the mains lead to the power



indicate that the appliance is operating. The

electronic thermostat makes a self test, 20

seconds before the compressor starts.

Temperature control

It is recommended to check the inside

temperature with an accurate thermometer

once a day. The inside temperature must

be checked regularly according to WHO’s



Fig. 4

Cool down of the appliance

Before the appliance is loaded with

vaccines the ice-lining in the 4 sides must

be frozen. To ensure that the ice-lining in

the 4 sides is frozen do the following:

1. Place a thermometer in the top basket.

2. Plug in the appliance, and let it run for

24 h.

3. Check the temperature in the top and

bottom basket (must be between +2° and

+8°C).

The temperature in the vaccine

compartment must always be monitored

on the thermometer and be within the

range +2° to +8°C. Due to tolerance of the

thermostat you should always control the

temperature during cool down.

6

GB

Fig. 4

Loading the appliance

Loading vaccines

When the temperature in the vaccine

compartment has stabilized, i.e. and the

temperature is between +2° and +8°C and

the compressor stops and starts, vaccines

can be loaded. The vaccines should be

placed and arranged in the baskets, and





To ensure air-circulation and prevent too

low vaccine temperature, direct contact

to the inside walls must be avoided. The

Vaccine load in the bottom basket shall not

be higher than 250 mm.

Fig. 6

Do not load lower baskets

above this height (250mm)

Fig. 5

Fan



GB

Daily maintenance:

The temperature in the vaccine

compartment must always be monitored

on the thermometer every day. Please note

that the vaccine in the appliance may not

freeze.

Weekly maintenance:

During normal use, water can accumulate

at the bottom of the appliance; remove with

a cloth or through the drainage hole.

Wipe of water droplets on the inside wall at

the same time.

Under certain ambient conditions, rime can

form on the inside wall. Remove the rime

without using sharp edged tools.

Check if lid gasket is sealing tight to the top

frame when the lid is closed. A tight sealing

lid reduces accumulation of water and for-



Monthly maintenance:

Clean the grill on the right side of the

refrigerator once each month.

Yearly maintenance:

Electric connections and components are

to be checked and cleaned once a year or

more if necessary.

Maintenance and cleaning

Cleaning

Disconnect the power supply before

cleaning. The best way to clean the

appliance is by using luke warm water with

a small amount of unscented detergent.

Never use cleaning agents that scour. Use

a soft cloth. Rinse with clean water and dry

thoroughly. It is important to prevent water

from running into the control panel.

The sealing strip around the lid must be

cleaned regularly to prevent discolouration

and prolong service life. Use clean water.

After cleaning the sealing strip, check that it

continues to provide a tight seal.

If the appliance is not being used for any

period of time, switch off the appliance,

disconnect the power supply, empty the

appliance, clean the inside, and leave the

lid open to allow air circulation and prevent

smells.

8

GB

Trouble shooting

Fault Possible cause Remedy

Compressor is not run-

ning, and the ice packs

are not cold

Be patient, it is most likely that the

compressor will start within a few

minutes.

If this is not the case, check the fol-

lowing:

- Check that power is connected.

- Check the fuse and replace it if

necessary.

- If the above is OK, call technical

supervisor.

Compressor is running,

and the temperature is

too high

The ventilation grille is blocked.

The lid is not closed properly.

The temperature in the room in which

the appliance is installed is too high.

Ensure unhindered air circulation.

Ensure that the lid is closed properly.

Shield the appliance against direct

sun light and ensure more ventilation

to the room.

No temperature is

displayed

The thermometer is broken.

There is not enough light for the solar

sensor.

Change the thermometer.

Turn on the light.

Temperature goes

below +2°C in a spe-



Air circulation is restrickted.

Basket in direct contact with wall.

Check load hight is not above 250mm

(or loadline) in lower baskets.

Move the end basket a little to leave

a gap between the basket and the

wall.

9

GB

Product nr.

Warranty, spare parts and service

Warranty disclaimer

Faults and damage caused directly or

indirectly by incorrect operation, misuse,



installation or mains connection. Fire, ac-

cident, lightening, voltage variation or other

electrical interference, including defective

fuses or faults in mains installations are not

covered by the warranty.

Repairs performed by others than approved

service centres and any other faults and

damage that the manufacturer can sub-

stantiate are caused by reasons other than

manufacturing or material faults are not

covered by the warranty.

Please note that changes to the construc-

tion of the appliance or changes to the

component equipment of the appliance will

invalidate warranty and product liability, and

the appliance cannot be used lawfully. The

approval stated on rating plate will also be

invalidated.

Spare parts

When ordering spare parts, please state

the type, serial and product numbers of

your appliance. This information is given on

the rating plate. The rating plate contains

various technical information, including type

and serial numbers.



10

GB

MK 304

Please Note! The drawing covers all variants of the model and therefore contains more pos. numbers





3.1

Position Item number Item name

0061 0-6538001 Filter drier,



A

921001 Cover + wirring clamp

  Base plate fittings, set, complete

0129 8-036038480 Compressor - FR 8,5 G,HST Complete, R134a

2168  Display with remote control - EPT-R1

5000 3010049 Drain plug

5002 6000959 Foot with pin

5118  Lid foamed without handle/hinges

5119  Rubber gasket



A

93010210 Water ballast box

5401 1510031 Hinge 30

5450 3010040-01 Top part for hinge cover

5451 3010032-01 Bottom part for hinge cover

5605 304090501 Handle with lock (push and turn)

5606 8090342-94 Inlay for handle,

5682 1510046 Key, set - 2pc.

5683 2040145 Catch for handle

5684 3010265-01 Cover for catch

5685 600098801 Lock with keys,(push and turn)

  Thermostat phial (Fan box )

  Thermostat phial

  Thermostat

  Pilot lamp, green

  Thermometer, solar

 3040141 Control panel

5812 6520106 

5850 6520004 

 6000902 Fan

  Fan box, complete, inclusive heating element

 3510024 Basket

 3510023 Basket

5963

A

 Eutectic element

 3010308-01 Motor screen

6553  Mains lead

  Transformer, 230/2X12 DC

  Fan

Please Note!

The drawing covers all variants of the model and

therefore contains more

pos. numbers than your product. See the spare

parts list for exact product

specification.

 Version :... C Date :............. 22-05-2013

A

pproved b

y

:.... SUS

11

GB

12

GB

13

GB

Disposal

Information for Users on Collection

and Disposal of Old Equipment and

used Batteries

These symbols on the products,

packaging, and/or accompanying

documents mean that used electri-

cal and electronic products and

batteries should not be mixed with

general household waste. For proper

treatment, recovery and recycling

of old products and used batteries,

please take them to applicable collec-

tion points, in accordance with your

national legislation and the Directives

2002/96/EC and 2006/66/EC.

By disposing of these products and

batteries correctly, you will help to

save valuable resources and prevent

any potential negative effects on

human health and the environment

which could otherwise arise from

inappropriate waste handling.

For more information about collec-

tion and recycling of old products and

batteries, please contact your local

municipality, your waste disposal

service or the point of sale where you

purchased the items.

Penalties may be applicable for incor-

rect disposal of this waste, in accord-

ance with national legislation.

For business users in the Euro-

pean Union.

If you wish to discard electrical and

electronic equipment, please contact

your dealer or supplier for further

information.

[Information on Disposal in other

Countries outside the European

Union]

These symbols are only valid in the

European Union. If you wish to dis-

card this product, please contact your

local authorities or dealer and ask for

the correct method of disposal.

-

tom two symbol examples):

This symbol might be used in combi-

nation with a chemical symbol. In this

case it complies with the requirement

set by the Directive for the chemical

involved.

14

GB

15

GB

Caisson lesté d’eau

Information générale

Le modèle MK est un réfrigérateur à vac-

cins avec doublage de glace. Il possède un

compartiment pour le stockage de vaccins

(+2 °C à + 8 °C) muni de paniers.



Le modèle MK 304 est équipé d’un com-

presseur puissant pouvant fonctionner sur

un voltage de 22 % inférieur à la tension

nominale. Voir la plaque signalétique. Si les

variations de tension débordent cette plage,

l’emploi d’un stabilisateur automatique de

tension est recommandé.



Voir la plaque signalétique placée à l’arrière

de l’appareil.

Déballage et installation

Déballage

1. Déballer l’appareil et s’assurer qu’il n’a

subi aucun dommage. Si un dommage

est observé, contacter votre responsable

technique.

 

tension et quelle fréquence conviennent



3. Ouvrir et sortir tout le matériel emballé à

l’intérieur.

Table des matières

Information générale...................................2

Alimentation électrique ...............................2

Caractéristiques techniques .......................2

Déballage ...................................................2

Faire connaissance avec son réfrigérateur 3

Installation ..................................................4

Raccordement électrique............................5

Mise en service et fonctions .......................6

Refroidissement de l’appareil .....................6

Chargement de l’appareil ...........................

Entretien et nettoyage ................................8

 ............................9

Garantie, pièces de rechange et service ..10

Schéma de principe ..................................13

Mise au rebut ............................................14

Nous nous réservons le droit d’apporter



2

FR

Caisson lesté d’eau

Poignée

Joint d’étanchéité

Stockage de vaccins

Compartiment du compresseur

avec grille de ventilation



température



Faire connaissance avec son réfrigérateur

3

FR

800 mm

50 mm

100 mm

Il doit y avoir au moins 30 mm d’espace

entre la base de l’appareil et le sol.

Les ouvertures de ventilation sur l’appareil

ou sur la structure incorporée doivent être

maintenues libres de toute obstruction.

-

lation doit être libre.





Emplacement

L’appareil doit être placé dans une pièce

bien ventilée, à l’abri du soleil et loin des

autres sources de chaleur.

Lors de la mise en place de l’appareil, s’as-

surer que le sol est bien plan. Pour plus



Installation



4

FR

Préparation



votre support. Si ce n’est pas le cas, de-







Cordon élec-

trique



230 V 115 V

Marron Blanc Sous tension

Bleu Noir Neutre

Vert/Jaune Vert Terre



allumer l’interrupteur de l’appareil.



en route, sinon, contacter votre respon-

sable technique.



5

FR



L’appareil est muni d’un thermostat

électronique pour le contrôle de la

température dans le compartiment à

vaccins. Le thermostat est réglé au départ

d’usine.

1. La diode verte est allumée lorsque

l’appareil est connecté à l’alimentation

électrique.

2. Thermomètre.

Procédure de mise en route



courant. La diode verte doit s’allumer

(Fig. 4) pour indiquer que l’appareil est

en fonction. Le thermostat électronique

procède à son propre test, 20 secondes

avant la mise en route du compresseur.

Contrôle de la température



température intérieure une fois par jour à

l’aide d’un thermomètre précis. Selon les



température intérieure doit être contrôlée

régulièrement.

Refroidissement de l’appareil

Avant que les vaccins soient chargés dans

l’appareil, la contre-paroi réfrigérante sur

les 4 côtés doit être gelée. Pour s’assurer

que la contre-paroi réfrigérante sur les 4

côtés est bien gelée, procéder comme suit :

1. Placer un thermomètre dans le panier

supérieur.

2. Branchez l’appareil et laissez-le

fonctionner pendant 24 h.

3. Contrôler la température dans les paniers

du haut et du bas (celle-ci doit se situer

entre +2 et +8 °C).

La température dans le compartiment à

vaccins doit être constamment contrôlée sur

le thermomètre et doit se situer dans une

fourchette de +2 à +8 °C. La précision du

thermostat permet un contrôle constant de

la température pendant le refroidissement.

Mise en service et fonctions

Fig. 4

6

FR

La page charge ...

Vestfrost MK 304 Instructions For Use Manual

Vestfrost MK 304 Instructions For Use Manual

dans d''autres langues

Documents connexes

Autres documents