Sanyo DP52449 - 52" LCD TV Le manuel du propriétaire

2

Need help? www.sanyoctv.com 1-800-877-5032

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding-type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not fit fully into your outlet, consult an electri-

cian for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the manu-

facturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

15. If an outside antenna is connected to the television

equipment, be sure the antenna system is grounded so

as to provide some protection against voltage surges

and built up static charges. In the U.S. Selection 810-21

of the National Electrical Code provides information with

respect to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of

antenna discharge unit, connection to grounding elec-

trodes, and requirements for the grounding electrodes.

16. An outside antenna system should not be located in the

vicinity of overhead power lines or other electrical light

or power circuits, or where it can fall into such power

lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from

touching such power lines or circuits as contact with

them might be fatal.

EXAMPLE OF ANTENNA GROUNDING ACCORDING

TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

“Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the build-

ing, as close to the point of cable entry as practical.”

17. Wall or Ceiling Mounting—The product should be

mounted to a wall or ceiling only as recommended by

the manufacturer.

18. Apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

19. When the MAINS plug is used as the disconnect device,

the disconnect device shall remain readily operable.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SER-

VICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A

RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS

UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

“As an Energy Star® Partner, Sanyo

Manufacturing Corporation has deter-

mined that this product meets the Energy

Star® guidelines for energy efficiency.”

This symbol on the nameplate means

the product is Listed by Underwriter’s

Laboratories Inc. It is designed and

manufactured to meet rigid U.L. safety

standards against risk of fire, casualty

and electrical hazards.

3

Need help? www.sanyoctv.com 1-800-877-5032

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-

dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void

the user’s authority to operate the unit.

TRADEMARKS

Manufactured under license from Dolby Laboratories.

“Dolby” is a trademark of Dolby Laboratories.

CONTAINS MERCURY LAMPS,

DISPOSE OF PROPERLY

SANYO recommends keeping the TV set at its fac-

tory settings or moving Energy Saver settings

from “Level 1” to “Level 2” or “Level 3” to further

re-duce power requirements and increase energy

savings. Doing so contributes to the sustainability

of our resources and environment.

For more information visit www.energystar.gov

PC RESOLUTION CHART

HDMI, the HDMI Logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

This Class B digital apparatus complies with Canadian

ICES-003.

4

Need help? www.sanyoctv.com 1-800-877-5032

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 2

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

THINK GAIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

PC RESOLUTION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

PROTECTING THE LCD SCREEN . . . . . . . . . . . . . . . . . . . . . .4

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

STAND REMOVAL / WALL MOUNTING . . . . . . . . . . . . . . .5

GETTING STARTED—

Remote Control Battery Installation . . . . . . . . . . . . . . . .5

Antenna Connections for off-air or cable . . . . . . . . . . .5

Universal Remote Control operation . . . . . . . . . . . . . . .6

PC CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

PC MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

BACK PANEL JACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

AUDIO / VIDEO CONNECTIONS . . . . . . . . . . . . . . . . . . . . . .9

POWER CONNECTION / INITIAL CHANNEL SEARCH . .10

ON-SCREEN MENU OPERATION—

Chanel Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . .11

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Energy Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Clock Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Manual Picture Settings . . . . . . . . . . . . . . . . . . . . . .15

Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Manual Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . .16

PHOTO VIEWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

HDMI LINKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

MOTION SYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

GXDB REMOTE ADVANCED OPERATIONS . . . . . . . . . . .19

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

REMOTE CONTROL

PROGRAMMING . . . . . . . . . . . . . . . . .Supplied Code Sheet

PROTECTING THE LCD SCREEN

The screen can be damaged if it is not maintained

properly. Do not use hard objects such as hard

cloth or paper. Do not use excessive pressure

when cleaning the screen; excessive pressure can

cause permanent discoloration or dark spots.

NEVER spray liquids on the screen.

HANDLING PRECAUTIONS

• Handle by the cabinet only. Never touch the

screen when handling.

• Excessive pressure on the screen can cause per-

manent discoloration or dark spots.

• Handling damage is not covered under warranty.

POSITIONING THE LCD HDTV

Always use a firm-flat surface when posi-

tioning your HDTV. Do not position the unit

in a confined area. Allow adequate space

for proper ventilation.

SPECIFICATIONS

Power Requirement:

Source: AC 120V, 60Hz

AC Power Consumption:

DP42849 216 watts

DP46849 255 watts

DP52449 240 watts

Dimensions:

MODEL WIDTH HEIGHT DEPTH

DP42849 39.8 27.7 12.1

w/o stand 25.7 4.7

DP46849 43.7 30.1 12.7

w/o stand 28.1 4.7

DP52449 49.7 34.4 14.6

w/o stand 32.4 5.0

NOTE: Dimensions are in inches

5

Need help? www.sanyoctv.com 1-800-877-5032

STAND REMOVAL AND WALL MOUTING (OPTIONAL)

Tools Needed: Phillips screwdriver

IMPORTANT NOTE:

Place HDTV face down

on a padded or cushioned surface to protect the screen and finish.

Wall mounting of the HDTV must be performed by a skilled person.

DP42849

DP46849

DP52449

GETTING STARTED

Install batteries in the remote control

( 2 “AAA”, not included)

PRECAUTIONS

To ensure safe operation, please observe

the following precautions:

• Replace both batteries at the same

time. Do not use a new battery with

a used battery.

• There’s a risk of explosion if a battery

is replaced by an incorrect type.

• Do not expose the Remote Control unit to moisture

or heat.

• Be sure to match the “+” and “

–” signs on the batter-

ies with marks inside the remote control.

ANTENNA CONNECTION FOR

OFF-AIR SIGNALS OR CABLE

Note: The tuner in this HDTV can receive digital and

analog off air signals from an antenna. It can also

receive analog or ClearQAM cable channels from

a direct Cable TV connection.

No. 3

ANTENNA

CABLE

ANALOG / DIGITAL

ANTENNA IN

1

Remove the four (4) screws securing the foot

stand. CAUTION: Hold the stand firmly as you

remove the last screw.

2

Use the screws you removed when detach-

ing the stand to secure the HDTV to a wall

mounting kit (kit not included.)

VESA standard interface: 400 x 400

Mounting screws measurements:

M6 (6mm) Diameter, Length—16mm (maximum)

1

Remove the four (4) screws securing the foot

stand. CAUTION: Hold the stand firmly as you

remove the last screw.

2

Use the screws you removed when detach-

ing the stand to secure the HDTV to a wall

mounting kit (kit not included.)

VESA standard interface: 400 x 400

Mounting screws measurements:

M6 (6mm) Diameter, Length—16mm (max.)

6

Need help? www.sanyoctv.com 1-800-877-5032

UNIVERSAL REMOTE CONTROL OPERATION

The Sanyo GXDB universal remote control allows

you to control up to 3 more audio/video devices

with one easy to use, compact remote control.

Follow the instructions in “Remote Control

Programming” (included in separate folded sheet)

to program the GXDB remote to control your

equipment.

Press... To... Press... To...

NOTE: “TV” mode is dedicated only to a Sanyo TV.

By pressing the TV key on your remote control

the Sanyo TV control code is reactivated.

Advanced programming instructions for your

GXDB remote can be found on pages 19 - 22 of

this owner’s manual.

7

Need help? www.sanyoctv.com 1-800-877-5032

PC CONNECTIONS AND SETUP

PC PICTURE (MANUAL) SCREEN

PC SOUND (MANUAL) SCREEN

PC SETTING SCREEN

PC Setting

Auto Adjustment – Automatically adjust display

position, dot clock and phase.

Dot Clock – Adjust the Dot frequency to match

your computer’s Dot frequency.

Phase – Adjust this parameter when the picture

appears to flicker or is blurred.

H-Position – Move the image horizontally

V-Position – Move the image vertically

Power Saving – Enable the HDTV to turn to

Standby Mode when computer is not in use.

PC Picture

Standard – Sets predetermined values to the

Picture parameters.

Manual – Adjust the screen’s Contrast, Brightness

and Color Temperature settings.

PC Sound

Standard – Sets predetermined values to the

Sound parameters.

Manual – Adjust the HDTV’s Bass and Treble

settings.

Note: Before connecting any cables, disconnect the

AC power cords of both the HDTV and PC from the

AC outlets.

Note: Power on the HDTV and any other peripheral

equipment before powering on the computer.

To avoid an “Out of Range” condition please set

your PC’s output resolution to one compatible with

your HDTV. See page 3.

PC OR LAPTOP

HDTV BACK

RGB Monitor

cable

Stereo mini

audio cable

NOTE:If computer has only DVI Output, a DVI to RGB

converter will be required (not included.)

DVI OUTPUT

JACK

RGB OUTPUT

JACK

Sanyo recommends using

a monitor cable that in-

cludes a Ferrite Core.

8

Need help? www.sanyoctv.com 1-800-877-5032

Digital Audio Output (Coaxial)

Component Video Input (VIDEO2 or VIDEO3)

Green (Y), blue (Pb), and red (Pr) Video inputs plus the

white and red Audio inputs.

PC Input and Stereo Audio (Mini)

• MONITOR RGB (D-SUB)

• AUDIO R/L (Stereo Mini Jack)

Analog / Digital Antenna Input

S-Video Input (VIDEO1)

NOTE: An S-Video connection will override a connection to

the Video1 (yellow) input jack.

Composite Video Input (VIDEO1)

Yellow (Video), plus white and red (Audio) input jacks.

Stereo Audio Out (L/R) Jacks

HDMI (INPUT1, 2 & 3)

An all digital AV interface that accepts uncom-

pressed video signals up to 1080p for the very

best picture possible.

NOTE: A DVI conection is possible via the HDMI (DVI)

INPUT1 using an appropriate adapter and connect-

ing the audio to the VIDEO3 Audio jacks.

USB Input

View pictures stored in a USB device.

1

2

3

4

5

6

7

8

9

1

2

3

4

5

7

9

6

BACK PANEL JACKS

8

Composite

S-Video

Component

H D M I

NOTE: Composite, S-Video, and Component video connections need their appropriate white and

red audio connections. High Definition image available from HD signals and HD equipment.

Above Standard

Standard High Definition

Optimum

High Definition

9

Need help? www.sanyoctv.com 1-800-877-5032

AUDIO / VIDEO CONNECTIONS

DVD PLAYER

(or similar device)

VCR

(or analog device)

STEREO

AMPLIFIER

MULTICHANNEL

RECEIVER

NOTE: Audio/Video cables are not supplied

Composite connections are used to hookup

your analog equipment such as a VCR or an

older DVD player.

S-Video connection can replace the yellow

Video connection for enhanced video.

Digital Audio Output is used to hookup a mul-

tichannel receiver with the use of a phono-type

digital audio cable.

Component connections will accept SDTV,

EDTV and HDTV video signals. Use them for

great image quality from digital devices.

SATELLITE RECEIVER

(or similar device)

USB DEVICE

Audio Output L/R are used to hookup an

external stereo Amplifier. (Do not connect

external speakers directly to the HDTV)

HDMI INPUT1 & 2 are used to hookup HD

digital devices such as a Blu-ray player, HD

Cable Box, HD Satellite Receiver or Video-

game System.

HDMI (DVI) INPUT1 can be used to hookup

a DVI device with the use of an appropriate

adapter. (VIDEO3 Audio in L/R jacks need to

be hooked up to the DVI device as well)

USB input jack is used

to connect a USB mass

storage device to watch

JPEG.

DVI

10

Need help? www.sanyoctv.com 1-800-877-5032

GETTING STARTED— INITIAL CHANNEL SEARCH (FIRST POWER ON)

Turn On TV

Wait for on-screen instructions to per-

form an Initial Channel Search.

CHANNEL SEARCH

Checks Antenna and Cable signals con-

nected to the Antenna terminal.

AV SEARCH

Searches for signals from devices con-

nected to the AV input jacks.

Note: Power ON external devices connected to the TV before

comencing an AV Search.

An AV search will begin if no Antenna signals are

detected, if neither of these searches detect signals,

the HDTV will tune to input Video1.

Plug in AC power cord

120V AC, 60Hz

INITIAL SETUP SCREEN

CHANNEL SEARCH METHOD SCREEN

CHANNEL SEARCH PROGRESS SCREEN

Note: “Auto” detects the mode detection, Cable or Air, first,

and then proceeds with the channel search.

ON SCREEN HELP MENU

Access an on screen trouble shooting

guide (in the Initial Setup Screen.)

You may acces the On Screen Help

menu later on at any time via the main

menu or by pressing the HELP key on

your remote control.

11

Need help? www.sanyoctv.com 1-800-877-5032

CHANNEL SETTING

Auto – Searches the detected mode, Cable or Air.

Cable – Searches for analog and unscrambled

(ClearQAM) digital cable channels.

Air (Antenna) – Searches for analog and digital off-air

channels.

Digital Air Add-On – Searches digital off-air channels

adding newly found digital channels to the channel

map database.

CHANNEL SETTING SCREEN

MAIN MENU SCREEN

CHANNEL SEARCH

Display the On Screen menu and use the

CURSOR  keys to select Channel

Setting. Press ENTER.

NOTE: Digital Air Add-On option is not available when the

current mode is Cable.

ON-SCREEN MENU OPERATION

Channel Scan Memory lists all Analog and Digital

channels found. It also lists Analog channels that were

not found, which can be added.

CHANNEL SCAN MEMORY

CHANNEL SCAN MEMORY SCREEN

Move the channel select bar

through all channels, enabled and

disabled.

Move the channel select bar

through enabled channels, skipping

all disabled channels.

Enable a disabled channel or dis-

able an enabled one.

NOTE: For information on local digital channels,

visit www.antennaweb.org

IMPORTANT FACT: This HDTV maintains only one data-

base of digital channels. Therefore, when you search for

cable channels, the database of antenna digital channels

will be deleted. You will only be able to receive those

ClearQAM channels your cable company provides.

12

Need help? www.sanyoctv.com 1-800-877-5032

SETUP

Display the On Screen menu and use the

CURSOR  keys to select Setup. Press

ENTER.

ON-SCREEN MENU OPERATION

Choose between English, Spanish and French for your

On Screen menu’s display language. Press ENTER on

the desired language.

MENU LANGUAGE

MAIN MENU SCREEN

SETUP MENU LANGUAGE SCREEN

A blue marker indicates the current

selected option.

DIGITAL CAPTION SCREEN

Use the Setup menu to set the Menu Language, V-

Chip rating settings, customize Digital Captions, set

Energy Saver level, set the current time and on-time

with the Clock Timer, and establish the HDMI Linking

CEC function.

Captioning is textual information transmitted along

with the picture and sound. Turning Captioning ON

causes the HDTV to open these captions (digital or ana-

log) and superimpose them on the screen.

Digital Caption’s Font, Background and Foreground

display may be customized:

DIGITAL CAPTION

Navigate the cursor

(highlight)

Select / set parameter.

NOTE: Local broadcasters decide which caption signals

to transmit.

13

Need help? www.sanyoctv.com 1-800-877-5032

SETUP (CONTINUED)

ON-SCREEN MENU OPERATION

Use this feature to automatically block programs with

content you deem as inappropriate for viewing by your

children.

V – CHIP

SETUP V-CHIP SCREEN

ADJUST (STANDARD) SCREEN

Navigate the cursor

(highlight)

Make selection.

Block or unblock the selected

Rating option.

NOTE: Blocking a rating will block all higher ratings automa-

tically. Unblocking a rating unblocks all lower ratings

automatically.

ADJUST (ADVANCED) SCREENS

Advanced V-Chip System

This feature is an advanced Regional rating system for

digital channels.

When the HDTV detects compatible Rating Region

Table (RRT) data, it’s downloaded & stored in memory.

The Setup V-Chip screen is then modified to show the

Adjust (Advanced) option.

Use the CURSOR  and keys to highlight the

different options. Use the ENTER key to block or

unblock the selected rating.

NOTE: This feature is designed to comply with the United

States of America’s FCC V-Chip regulations. Therefore,

it may not function with broadcasts that originate in

other countries.

MORE INFORMATION

Additional information about MPAA (Motion Picture

Association of America) and V-Chip rating can be

found at: www.mpaa.org and www.v-chip.org,

respectively.

14

Need help? www.sanyoctv.com 1-800-877-5032

SETUP (CONTINUED)

ENERGY SAVER SCREEN

Energy saver settings control the LCD backlight bright-

ness to save power consumption.

The higher the level number, the more brightness

reduction and higher power saving.

ENERGY SAVER

Set the Current Time for your HDTV. You may also set

a Switch on Time to use with the On Timer Function.

When On Timer Function is set to ON, the TV will auto-

matically turn on at the previously set Switch on Time.

CLOCK TIMER

CLOCK TIMER SCREEN

ON TIMER FUNCTION SCREEN

Change the value of the current

selection.

Move to the next or previous value

that you wish to change.

Save the desired Time entry.

Set the On Timer Function ON or OFF.

ON-SCREEN MENU OPERATION

LLEEVVEELL 11 LLEEVVEELL 22 LLEEVVEELL 33

15

Need help? www.sanyoctv.com 1-800-877-5032

PICTURE

ON-SCREEN MENU OPERATION

Display the On Screen menu and use the

CURSOR  keys to select Picture.

Press ENTER.

MAIN MENU SCREEN

You may choose between Movie, Sports, News,

Game, and Standard, which have predetermined fixed

picture parameter values, or one of the two Manual

options for customized personal settings.

NOTE: Each AV input can have its own picture mode (pre-

determined or manual.) Current input’s selected

option is indicated by a blue marker.

Choose Manual to adjust Color, Tint, Contrast,

Brightness, Sharpness, Signal Balancer, Noise Re-

duction and Dynamic Contrast values.

Advanced Manual offers a Detailed Setting sub-menu

with the following options: Expanded DNR, White

Balance, Vertical Sharpness, Edge Enhancer, H-Size

and V-Size.

MANUAL PICTURE SETTINGS

Cycle through the different Picture

parameters.

Adjust the value of the selected

parameter.

Enter selected parameter’s adjust-

ment screen.

Set the value of the selected param-

eter and return to parameter selec-

tion screen.

PICTURE SCREEN (MANUAL)

PARAMETER SELECTION SCREEN

Select Manual or Advanced Manual.

VALUE ADJUSTMENT SCREEN EXAMPLES

NOTE:

CURSOR  keys select the next/previous

parameter without returning to the previous

menu screen.

16

Need help? www.sanyoctv.com 1-800-877-5032

SOUND

Display the On Screen menu and use the

CURSOR  keys to select Sound.

Press ENTER.

Choose one of the four available options for your

sound settings:

Auto – Sound setting levels are adjusted and linked

according to the current Picture option.

Standard – Neutral values for sound parameters.

Manual – Set Bass and Treble levels to your preference.

Advanced Manual – Use a 4-Band Equalizer to person-

alize sound settings.

MAIN MENU SCREEN

MANUAL PARAMETER SCREEN

ADVANCED MANUAL PARAMETER SCREEN

VALUE ADJUSTMENT SCREEN EXAMPLES

Cycle through the different Sound

parameters.

Adjust the value of the selected

parameter.

Enter selected parameter’s adjust-

ment screen.

Set the value of the selected param-

eter and return to parameter selec-

tion screen.

Select Manual or Advanced Manual.

ON-SCREEN MENU OPERATION

MANUAL SOUND SETTINGS

17

Need help? www.sanyoctv.com 1-800-877-5032

HDTV BACK PANEL

USB DEVICE

PHOTO VIEWER (USB)

USING THE PHOTO VIEWER

Press ENTER on a thumbnail photo to enable the

Rotate, Full View and Start Slideshow functions.

Once in Full View mode:

Use the CURSOR keys to change picture.

Press ENTER to show the full view options menu.

SLIDE SHOW

In the Slideshow Setup menu you may turn the Shuffle

and Quick Change options ON or OFF.

Choose Start Slideshow after pressing ENTER on a

thumbnail picture or in the Full View options menu to

start the slideshow from the current picture.

JPEG VIEWER USB MENU

Press MENU when in Full View or Slideshow mode to

display the USB On screen menu.

Picture Setting

– Adjust Color, Tint, Contrast,

Brightness, Sharpness and Dynamic Contrast.

NOTE: Picture Settings are separate configurations from the

settings in TV and AV inputs.

USB MAIN MENU SCREEN

THUMBNAIL VIEW SCREEN

NOTE: A thumbnail hide icon will appear if a pic-

ture cannot be decoded or no thumbnail

data is available.

SLIDE SHOW

SETUP MENU

FULL VIEW

OPTIONS MENU

View pictures on your HDTV with the use of a USB

mass storage device.

NOTE: The HDTV switches to USB Input when a USB device

is detected.

18

Need help? www.sanyoctv.com 1-800-877-5032

Use the HDMI-CEC Function to enable or disable all

available CEC functions.

HDMI Power ON Sync and Power OFF Sync enable

specific features including the automatic power ON

process and power OFF process.

HDMI LINKING

HDMI LINKING SCREEN

With a Sanyo Xacti Digital Video/Movie

Camera hooked up to your HDTV’s

HDMI input, setting the HDMI-CEC

Function to ON enables you the use of

keys on your GXDB universal remote to

operate your Xacti camera.

Xacti-LINK

GXDB XACTI-LINK KEYS

The CEC feature allows the control of multiple

CEC-enabled devices with one remote control,

and the interaction of devices with each other

without user intervention.

For example, a CEC-enabled device hooked up

to your HDTV may be turned off by turning off

the TV set, or setting the device on stand-by

will set the HDTV on stand-by as well.

CEC (Consumer Electronics Control)

Your Sanyo 52” HDTV DP52449 has a refresh rate of

120 Hz, it basically means that it “redraws” the image

on the screen twice as often than a common 60 Hz

refresh rate TV would.

Full – Takes full advantage of your TV’s refresh rate

capabilities for the best picture quality.

Theater – Best setting for original film movies

Off – Disables Full mode functions

NOTE: Even with Motion Sync set to Off, your HDTV still dis-

plays all images at a 120 Hz refesh rate.

MOTION SYNC (120 Hz) *DP52449 only

MOTION SYNC SCREEN

(ONLY AVAILABLE ON DP52449 MODEL)

NOTE: The HDMI-CEC function of the Xacti must also be

turned ON to enable the Xacti-Link.

NOTE: Designed for use with a Sanyo Xacti Digital

VIdeo/Movie Camera, and may not support all HDMI-

CEC functions of other equipment.

19

Need help? www.sanyoctv.com 1-800-877-5032

CHECKING THE CODES

If you have set up the remote using the procedure

in “Searching for Your Code”, you may need to

find out which five-digit code is operating your

equipment. For example, to find out which code is

assigned to your DVD:

1. Press DVD once.

2. Press and hold SET until the red LED blinks

twice, then release.

3. Enter 9 9 0. The LED blinks twice.

4. To view the first digit of the code, press 1.

Count the red LED blinks (for example, three

blinks = 3), and write down the number.

NOTE: If a code digit is 0, the LED does not blink.

5. Repeat step 4 for the four remaining digits,

using 2 for the second digit, 3 for the third digit,

4 for the fourth digit, and 5 for the fifth digit.

6. To check for other device codes, repeat steps

1—5, substituting the device key for the desired

mode you would like to check.

USING LEARNING

This universal remote control includes a Learning

feature (some models may not include Learning)

so you can add functions that are unique to your

home entertainment devices (e.g., VCR Tracking

Up or Down.) However, there are considerations.

LEARNING FEATURE PRECAUTIONS



Your original remote controls must be in work-

ing order for learning to work properly.



Learned keys are mode-specific, so each one

can store a unique function for each mode.



Do not use the following keys for Learning:

DEVICE KEYS, SET, or RECORD (



)



Learning capacity is approximately 42 to 75

keys, depending on the code being learned



Certain device functions are not learnable

including multi-frequency types, some high fre-

quency functions, and other unusual formats.



For optimum learning, avoid high levels of

ambient light such as natural sunlight or

energy-efficient fluorescent lights.

NOTE: Please have your original remote controls

handy before programming Learning.

PROGRAMMING A LEARNED KEY

NOTE: If more than 10 seconds pass between key

presses, the remote exits programming.

1. Place the GXDB and your original control head-

to-head (about 2” apart). Also locate the key

(on your original remote control) that you want

the GXDB to learn. Press the mode key you

wish to learn functions on.

2. Press and hold SET until the LED blinks twice,

then release.

3. Enter 9 7 5. The LED blinks twice.

NOTE: If the LED displays one long flash instead, either

your batteries are low, or the remote has a memory

fault. In either case, the remote cannot learn a new key.

4. On your GXDB remote, press the key that you

wish to learn onto. The feedback LED stays lit

for three seconds, suggesting the remote is

ready to learn.

5. On the original remote, press and hold the key

to be learned. Continue holding the key on the

original remote until the GXDB’s LED blinks

twice.

NOTE: If the red LED displays one long blink, a learning

error has occurred. Try repeating this step again until a

successful capture occurs. If the function is still not cap-

tured, press and hold SET to exit programming and

review the “Learning Feature Precautions”.

6. Repeat steps 4 through 5 for another key you

would like to learn onto. Once you have com-

pleted learning all keys, press and hold SET

until the LED blinks twice to save all data

learned.

UNIVERSAL REMOTE CONTROL, ADVANCED OPERATION

20

Need help? www.sanyoctv.com 1-800-877-5032

DELETING A SINGLE LEARNING KEY

This process returns the key to its original pro-

gramming for the mode you select. You can also

delete learned programming by teaching a differ-

ent function to the key (see “Programming a

Learned Key”.)

NOTE: If more than 10 seconds pass between key press-

es, the remote exits programming.

1. Press the mode key that you wish to remove

the learned key from.

2. Press and hold SET until the LED blinks twice,

then release.

3. Enter 9 7 6. The LED blinks twice.

4. Press the key containing the learned function to

be deleted twice. The LED blinks twice and

exits from programming.

DELETING ALL LEARNED KEYS IN A

SPECIFIC MODE

NOTE: If more than 10 seconds pass between key press-

es, the remote exits programming.

1. Press and hold SET until the LED blinks twice,

then release.

2. Press 9 7 6. The LED blinks twice.

3. Press a mode key twice (i.e., DVD, STB, or AUX)

to clear all the learned keys for that mode. The

LED blinks twice and exits from programming.

CHANGING VOLUME LOCK

The GXDB universal remote control comes preset

to allow independent volume control of each

selected device (Global Volume Unlock). However,

you may change the Volume Lock setting to Global

Volume Lock so that one device's volume controls

volume in all other modes. After that, you can per-

form Individual Volume Unlock on a selected

device to set its volume control for independent

operation or Global Volume Unlock to remove all

volume locking.

LOCKING VOLUME CONTROL TO ONE MODE

(GLOBAL VOLUME LOCK)

1. Press and hold SET until the red LED blinks

twice, then release.

2. Enter 9 9 3, the LED blinks twice.

3. Press the mode key for the device you want to

control (for example, TV.)

4. The LED blinks twice. Now when you press

VOL

+

, VOL

–

, or MUTE, the selected device (for

example, TV) controls the volume regardless of

the current mode.

UNLOCKING A SINGLE DEVICE’S VOLUME

CONTROL

1. Press the desired device mode key (TV, DVD,

STB, or AUX).

2. Press and hold SET until the red LED blinks

twice, then release.

3. Enter 9 9 3. The LED blinks twice.

4. Then press VOL

–

. The red LED blinks four times.

Volume is independently controlled for the

selected devices.

UNLOCKING ALL VOLUME CONTROL (RES-

TORING GLOBAL UNLOCK)

1. Press and hold SET until the red LED blinks

twice, then release.

2. Enter 9 9 3, the LED blinks twice.

3. Press VOL

+

.The LED blinks four times. Volume

is independently controlled for all programmed

devices.

PROGRAMMING CHANNEL LOCK

Channel control can be locked so that the GXDB

remote controls a single device’s channel-chang-

ing functions, regardless of operating mode. This

is often enabled by users who watch all broadcast

TV through one device (e.g., a cable set-top box).

The affected keys are 1 – 0, CH, CH, and

RECALL.

LOCKING ALL CHANNEL CONTROLS TO ONE

DEVICE

To lock all channel-control functions to a specific

device, follow these steps:

1. Press the mode key that relates to the device

that you use for channel changing control.

UNIVERSAL REMOTE CONTROL, ADVANCED OPERATION

La page charge ...

Sanyo DP52449 - 52" LCD TV Le manuel du propriétaire

Ce manuel convient également à

Sanyo DP52449 - 52" LCD TV Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents