Samsung SC20F70HA Manuel utilisateur

English

Vacuum Cleaner

user manual

Thank you for purchasing a Samsung product.

To receive a more complete service,

please register your product at

www.samsung.com/register

SC20F70 Series

SC07F70 Series

✻ Before operating this unit, please read the instructions carefully.

✻ For indoor use only.

CLEAN THE DUST BIN WITH WATER

1 2 3 4

Take the dust bin out by

liﬁng the handle

Push the button aside. Turn the grille and take

out it.

Push the button.

5 6 7

Separate the dust bin

from body.

Clean the dust bin and

body with water.

Leave the dust bin and

body in the shade until

completely dry.

ACCESSORY (OPTION)

• Pull out the button, to use the dusting brush.

• To use the crevice tool, push the accessory on to the end of the hose handle in the opposite

direction.

safety information _03

safety information

SAFETY INFORMATION

WARNING

• Before operating the appliance, please read this manual thoroughly and retain it for your

reference.

WARNING

• Because these following operating instructions cover various models, the characteristics of

your vacuum cleaner may differ slightly from those described in this manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

Represents something you must NOT do.

Represents something you must follow.

Indicates that you must disconnect the power plug from the socket.

This vacuum cleaner is designed for household use only.

Do not use this vacuum cleaner to clean building waste and debris.

Regularly keep the ﬁlters in clean conditions to prevent of collecting ﬁne dust in them.

Do not use this vacuum cleaner with any of the ﬁlters removed.

Failure to meet these requirements could cause damage to the internal parts and void

your warranty.

WARNING

04_ safety information

IMPORTANT SAFEGUARDS

GENERAL

• Read all instructions carefully. Before switching on, make sure

that the voltage of your electricity supply is the same as that

indicated on the rating plate on the bottom of the cleaner.

• WARNING : Do not use the vacuum cleaner when rug or ﬂoor is

wet. Do not use to suck up water.

• Close supervision is necessary when any appliance is used by

or near children. Do not allow the vacuum cleaner to be used

as a toy. Do not allow the vacuum cleaner to run unattended at

any time. Use the vacuum cleaner only for its intended use as

described in these instructions.

• Do not use the vacuum cleaner without a dust bin.

Empty the dust bin before it is full in order to maintain the best

efﬁciency.

• Do not use the vacuum cleaner to pick up matches, live ashes or

cigarette butts. Keep the vacuum cleaner away from stoves and

other heat sources. Heat can deform and discolour the plastic

parts of the unit.

• Avoid picking up hard, sharp objects with the vacuum cleaner as

they may damage the cleaner parts.

Do not stand on the hose assembly. Do not put weight on the

hose.

Do not block the suction or the exhaust port.

• Switch the vacuum cleaner off on the body of the machine

before unplugging from the electrical outlet. Disconnect the plug

from the electrical outlet before emptying the dust bin. To avoid

damage, please remove the plug by grasping the plug itself, not

by pulling on the cord.

• This appliance can be used by children aged from 8 years and

above and people with reduced physical, sensory or mental

safety information _05

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be done by children without supervision.

• Children should be supervised to ensure that they do not play

with the appliance.

• The plug must be removed from the socket outlet before

cleaning or maintaining the appliance.

• The use of an extension cord is not recommended.

• If your vacuum cleaner is not operating correctly, switch off the

power supply and consult an authorized service agent.

• If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualiﬁed person in

order to avoid a hazard.

• Don’t carry the vacuum cleaner by holding the hose.

Use the handle on the vacuum cleaner set.

• Unplug the cleaner when not in use.

Turn off the power switch before unplugging.

UV BRUSH

• Since the UV rays from the UV Brush damage skin and eyes,

never allow the rays to make contact with skin or eyes and

do not let children or the elderly use the UV Brush. If used

incorrectly it may cause damage to a persons eyesight.

• If the transparent window is broken and the UV rays are exposed

directly, turn the power off and contact the service center.

• Do not use the UV Brush for purposes other than the sterilization

of mattresses, bedclothes, beds, cushions and so on made from

material. The company will not be held liable for any loss due to

accidents from using the UV Brush for purposes other than its

original purpose as listed above.

safety information

06_ safety information

• Do not sit on the UV Brush or drop it, and avoid imparting

impacts on the product. Failing to do so may result in injury or

product damage.

• Do not touch the power terminals on the back of the UV Brush

with a metal pin or rod. This may result in electric shock or ﬁre.

• When the UV lamp is out of order, never disassemble or modify

the product yourself.

Please contact the manufacturer or service center for a

replacement.

• Since an internal discharge occurs within the UV Brush, never

use the product near an inﬂammable spray or substance.

• Take care not to touch the UV lamp window after using the

UV Brush for an extended period of time as the surface of the

window may be hot.

• The UV Brush may start slowly at a low temperature due to the

inherent characteristics of UV lamps. Please keep the UV Brush

indoors.

contents _07

contents

ASSEMBLING THE CLEANER

08

OPERATING THE CLEANER

09

09 Power cord

09 ON/OFF Switch

10 Power control

12 Using the UV brush (SC20F70U Series)

13 Using the Dust Sensor (Option)

TOOLS AND MAINTENANCE

FILTER

15

15 Using accessory

17 Maintain ﬂoor tools

20 Cleaning the Dust Sensor (Option)

20 Emptying the dust bin

21 Clean the Grille

22 Clean the dust bin with water

23 Cleaning the dust ﬁlter

24 Cleaning the dust ﬁlter

25 Cleaning the outlet ﬁlter

TROUBLESHOOTING

26

08_ assembling the cleaner

• For storage, park the ﬂoor nozzle.

Please do not pick up a machine while the ﬂoor

nozzle parked

assembling the cleaner

OPTION

operating the cleaner _09

02 OPERATING THE CLEANER

POWER CORD

CAUTION

• When removing the plug from the electrical outlet, grasp the plug, not the

cord.

ON/OFF SWITCH

operating the cleaner

10_ operating the cleaner

POWER CONTROL

Hose Handle (SC20F70H Series)

1. ON/OFF [ ] Button

- Press the ON/OFF button to operate the vacuum cleaner.

Press again to stop the vacuum cleaner.

2. [(-/+)] Button

- Press the MODE button repeatedly to select the correct mode.

(ON) MIN → MAX

3. [ ] Button

- Press the [ ] button to operate the vacuum cleaner quietly.

Don’t cover the handle transmitter when you use a

handle control button.

HOSE (SC07F70H Series)

1. ON/OFF [ ] Button

- Press the ON/OFF button to operate the vacuum cleaner.

Press again to stop the vacuum cleaner.

2. [(-)], [(+)] Button

- Press the (+) button to increase the vacuum's suction power.

Press the (-) button to decrease the vacuum's suction power.

Don’t cover the handle transmitter when you use a

handle control button.

If no button is pressed for 30 minutes while cleaning, the

safety device is activated and the power is cut off.

In this case, press the [Power] button on the main unit or

unplug and then plug the power cord in again.

HOSE (SC20F70U Series)

1. ON/OFF [ ] Button

- Press the [ ] button to operate the vacuum cleaner. Press

again to stop the vacuum cleaner.

2. [SUCTION (-/+)] Button

- Press the [SUCTION (-/+)] button to increase or decrease the

suction power. Each time you press the button, you gradually

increase the suction power. After the suction power reaches its

maximum, the next time you press the button, you return the

suction power to its minimum.

3. [BRUSH ON/OFF] Button

- Press the [BRUSH ON/OFF] button to operate the UV Brush.

Press again to stop the UV Brush.

Don’t cover the handle transmitter when you use a handle control button.

If no button is pressed for 30 minutes while cleaning, the safety device is activated and the

power is cut off.

In this case, press the [Power] button on the main unit or unplug and then plug the power cord

in again.

Handle Control

The cleaner is controlled by radio

frequency signals.

- +

sender

Handle Control

The cleaner is controlled by radio

frequency signals.

sender

Handle Control

The cleaner is controlled by radio

frequency signals.

-/+

sender

operating the cleaner _11

02 OPERATING THE CLEANER

Change the battery

• When the vacuum cleaner does not work, replace the batteries.

If the problem persists, please contact our authorized dealer.

• Use 2 batteries of size AAA.

1. Never disassemble or recharge the batteries.

2. Never heat up the batteries or throw them into a ﬁre.

3. Do not reverse (+), (-) poles.

4. Dispose of the batteries property.

BODY

Press the power ON/OFF button repeatedly to start and to stop

the vacuum cleaner. (OFF → ON → OFF)

If the remote handle control is not working, the cleaner

can be operated using the ON/OFF button on the body

of the machine.



The ON/OFF button toogles the vacuum between the on and off states.



The ﬁlter light is illuminated when the dust pack requires checking or emptying.

Before performing this operation, make sure that there is no blockage in the tube, hose or brush.

CAUTION

operating the cleaner

1

2

BATTERY TYPE : AAA Size

12_ operating the cleaner

USING THE UV BRUSH (SC20F70U SERIES)

1. Insert the brush into the hose handle.

• Insert the UV brush securely into the hose handle until you hear a “clicking”

sound.

2. Press the [BRUSH ON/OFF] button to start cleaning.

• Press the [BRUSH ON/OFF] button and choose the appropriate

suction strength for the cleaner.

• It is advisable to select the (Max) suction strength setting.

• UV sterilization cannot be activated by itself.

3. When you have ﬁnished UV cleaning, press the [ ] button.

• Press the [ ] button to stop the cleaner.

- For safety reasons, UV brushing only runs for 30 minutes and then stops

operating. To resume the operation, press the [SUCTION (-/+)] button again.

The UV brush, which is inserted into the hose handle (not directly connected to the telescopic

pipe), is dedicated for bedclothes.

CAUTION

operating the cleaner _13

02 OPERATING THE CLEANER

USING THE DUST SENSOR (OPTION)

Dust Sensor Operations

• Indicates the amount of sucked in

dust so that users can experience

the successful operation of the

product while cleaning the room.

• The dust sensor is automatically turned on when the cleaner runs and turned off when the cleaner is

stopped.

• Since the dust sensor runs on battery power, there is no separate switch.

Installing the Batteries

• If the dust sensor doesn’t work even after cleaning the sensor, replace the batteries with new ones.

AAA type batteries are required.

• Do not disassemble or recharge the used batteries.

• Do not heat the batteries or put them in a ﬁre.

• Check the polarities (+ ,-) before inserting the batteries.

• Put the used batteries into the battery recycle bin.

• When you are not using the product for an extended period of time, separate the batteries.

CAUTION

operating the cleaner

• Green : When the amount of

sucked in dust is small.

• Red : When the amount of

sucked in dust is large.

Check the polarities

1 2 3

14_ operating the cleaner

Cleaning the dust sensor (Option)

• Since the dust sensor consists of sensitive electronic devices, if water or

other liquids enters the sensor, it may cause a problem.

• If you use athe dust sensor without closing the battery compartment

cover, pollutants such as dust may accumulate in the compartment

and cause a problem. Therefore, be sure to use the product with the

compartment cover closed.

• Take care when you use the cleaner because the dust sensor may

malfunction or may break due to an impact.

Installing the Dust Sensor

• Assemble the dust sensor between the air inlet connector on the neck of

the brush and the extension pipe. (Recommended)

You can assemble the dust sensor between the extension pipe and the

hose.

Dust Sensor (2 EA)

The assembly position of

the dust sensor

tools and maintenance ﬁlter _15

03

TOOLS AND MAINTENANCE FILTER

USING ACCESSORY

Pipe

• Adjust the length of the telescopic pipe by sliding the length control

button located in the center of the telescopic pipe back and forth.

• To check for blockages, separate the telescopic pipe and adjust to

shorten. This allows for easier removal of waste clogging the tube.

Accessory (Option)

• Pull out the button, to use the dusting brush.

• To use the crevice tool, push the accessory on to

the end of the hose handle in the opposite direction.

tools and maintenance ﬁlter

16_ tools and maintenance ﬁlter

Accessories (SC20F70U Series)

• Push the accessory onto the end of the hose

handle.

• Pull out the dusting brush to use the crevice tool.

• Push the accessory onto the end of the pipe.

• Pull out the dusting brush to use the crevice

tool.

Accessory (Option)

• Furniture brush for desk, Furniture and Floor.

tools and maintenance ﬁlter _17

03

TOOLS AND MAINTENANCE FILTER

MAINTAIN FLOOR TOOLS

2-Step Brush

• Adjust the inlet lever according to the ﬂoor surface.

• Remove waste matter completely if the inlet is blocked.

Power Pet Plus Brush (Option)

Frequent vacuuming of hair or pet fur may cause a falling-off of the rotation due to matters tangled around

the drum. In this case, clean the drum with care.

1. Push the Open button of the transparent screen cover to separate the cover.

2. Remove the brushbar from the transparent screen.

3. Remove waste matter such as dust and hair tangled around the brushbar using scissors.

4. Remove dust inside the brush housing using a dry duster or crevice tool.

5. Insert brushbar into rotating belt and assemble.

6. Click the transparent screen cover back into place to reassemble.

Parquet Master Brush (Option)

• Vacuum dust in wide area at once.

• Remove waste matter completely if the inlet is

blocked.

tools and maintenance ﬁlter

Carpet Cleaning Floor Cleaning

1 2

4 5

3

6

For improved pickup

of pet hair and ﬁbre on

carpets.

18_ tools and maintenance ﬁlter

Mini turbo brush (Option)

- To replace brushroll

1. If a clog is present or debris is visible, unscrew the two screws on

the back of the Mini turbo brush to remove the faceplate and clear

any obstructions.

2. Inspect condition of brushroll.

Replace brushroll if brushes are worn down.

To remove brushroll, pull up and out of end slots in nozzle housing.

Insert ends of brushroll into same slots to replace.

Inspect belt to ensure that it is in good condition.

If belt is broken or cracked, replace belt according to To Replace

Belt instructions.

3. Using at MAX.

Press the MAX button to operate the vacuum at maximum intake.

- To replace belt

1. Remove bottom plate.

See ﬁgure in To Replace Brushroll instructions.

2. Loop one end of new belt around shaft of pulley.

3. Loop other end of belt around designated area for it on brushroll.

Insert brushroll into slots in nozzle housing.

See ﬁgure in To Replace Brushroll instructions.

4. Fit Mini turbo brush back together as described in To Replace

Brushroll instructions.

tools and maintenance ﬁlter _19

03

TOOLS AND MAINTENANCE FILTER

To remove dust from the dust bin of the UV brush (Option)

When you notice that the dust bin is ﬁlled, use the [Dust Removal] button to empty the dust bin.

1. To remove dust from the dust bin, move the [Dust Removal] button

to the “Open” position.

- While the cleaner is operating (suction), use the [Dust Removal]

button for this purpose.

2. When done, move the [Dust Removal] button to the “Close”

position.

- When the [Dust Removal] button is in the “Open” position, the

suction power of the cleaner is reduced.

Cleaning the UV brush (Cleaning the drum) (Option)

Human and pet hair often becomes tangled in the drum, causing a reduction in the rotary power of the

the drum. To prevent this, clean the drum on a regular basis. Before the operations make sure that UV

brush is off.

1. Push the [Open Transparent Cover] button inward to remove the

cover.

2. Use the crevice tool to remove impurities such as dust and hair

from around the drum.

3. When done, push the [Open Transparent Cover] button outward to

close the cover.

tools and maintenance ﬁlter

20_ tools and maintenance ﬁlter

CLEANING THE DUST SENSOR (OPTION)

If the green light is not lit while cleaning

• Check if the hose, extension pipe or the air inlet is clogged and clean it if

necessary.

• Empty the dust bin of the cleaner or clean the ﬁlters.

If the red light does not light up when cleaning a dusty

location

• Clean the sensors (2EA) in the dust sensor block with a dry cloth.

Take care when you clean the sensors in the dust sensor block so that the sensors are not

damaged.

EMPTYING THE DUST BIN

1 2 3

Once dust reaches the dust full

mark, empty the dust bin.

Take the dust bin out by liﬁng

the handle

Push the button aside.

4 5 6

Click

Throw the dust away in the bin. Close the dust bin cover.

Before use, push the dust

bin into the main body of the

vacuum cleaner until you hear

the “click” sound.

CAUTION

La page charge ...

Samsung SC20F70HA Manuel utilisateur

Samsung SC20F70HA Manuel utilisateur

dans d''autres langues

Documents connexes