AccuCold SCR600LBIMED2ADA Manuel utilisateur
- Catégorie
- Frigos
- Taper
- Manuel utilisateur
0
If you need service or call with a question, please have
this information ready. We advise you to keep this Use
& Care Guide in your possession.
Model:
______________
Serial number:
_________________
Options added:
Date of purchase:
Dealer:
MED2 Series
REFRIGERATORS & FREEZERS
FOR MEDICAL & LABORATORY STORAGE
FELIX STORCH, INC.
ISO 9001:2015 Registered
770 Garrison Avenue
Bronx, New York 10474
accucold
.com
USE & CARE GUIDE
NOTE: A French version of this
manual can be found
online at accucold.com
NOTE: The alarm/thermometer included in this unit has a NIST calibrated
probe that requires re-calibration every two years. The NIST calibration
expiration date is included on the device. In order to maintain your NIST
certification, you will need to re-calibrate your probe at that time. Contact us
at calibratio[email protected]m
1
Model Numbers
All-Refrigerators
•
FFAR24LMED2
Compact all-refrigerator with automatic defrost operation
•
FF28LWHMED2
Countertop all-refrigerator with automatic defrost operation
•
FF511LBIMED2 / FF511LBIMED2ADA
Undercounter all-refrigerator with automatic defrost operation
•
FF511LBI7MED2 / FF511LBI7MED2ADA
Commercially listed undercounter all-refrigerator with automatic defrost operation
•
FF7LBIMED2 / FF7LBIMED2ADA
Undercounter all-refrigerator with automatic defrost operation
•
FFAR10MED2
Mid-sized all-refrigerator with automatic defrost operation
•
SCR600LBIMED2 / SCR600LBIMED2ADA
Undercounter glass door all-refrigerator with automatic defrost operation
All-Freezers:
•
FS24LMED2
Compact all-freezer with manual defrost operation
•
FS24L7MED2
Commercially listed compact all-freezer with manual defrost operation
•
FS30LMED2
Countertop all-freezer with manual defrost operation
•
FS30L7MED2
Commercially listed countertop all-freezer with manual defrost operation
•
FS407LBIMED2 / FS407LBIMED2ADA
Undercounter all-freezer with manual defrost operation
•
FS407LBI7MED2 / FS407LBI7MED2ADA
Commercially listed undercounter all-freezer with manual defrost operation
•
VT65MLBIMED2 / VT65MLBIMED2ADA
Undercounter all-freezer with manual defrost operation
•
VT65MLBI7MED2 / VT65MLBI7MED2ADA
Commercially listed undercounter all-freezer with manual defrost operation
MODELS
2
Table of Contents
Model Numbers ......................................................................... 1
Appliance Safety ....................................................................... 3
Proper disposal of an old appliance ..................................... 3
Installation Instructions ........................................................... 4
Key Eject lock ....................................................................... 4
Location Requirements ...................................................... 5 – 6
Location ................................................................................ 5
Recommended grounding method ....................................... 5
Leveling your appliance ....................................................... 6
When using the appliance .................................................... 6
Energy-saving tips ................................................................ 6
Appliance Care .................................................................... 7 – 8
Defrosting ............................................................................. 7
Cleaning your appliance ....................................................... 7
Changing the light bulb ........................................................ 8
Loss of power ....................................................................... 8
Moving the appliance ........................................................... 8
Temperature Selection and Monitoring .......................... 9 – 11
Digital thermostat .................................................................. 9
Thermometer/alarm ...................................................... 10 –12
Keypad Lock ........................................................................... 13
Operation of Specific Models ................................................ 14
Troubleshooting ..................................................................... 15
Limited Warranty .................................................................... 16
3
Appliance Safety
Your safety and the safety of others are very important to us.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
You can be seriously injured or even killed if you don’t follow instructions.
Safety messages will tell you what the potential hazard is, how to reduce the
chance of injury, and what can happen if the in
structions are not followed.
•
Plug into a grounded 3-prong outlet.
•
Do not remove ground prong, nor use a 3/2 adapter.
•
Do not use an extension cord.
•
Be sure not to plug into outlets controlled by wall switches.
•
Disconnect power before servicing.
•
After servicing, replace all parts and panels before operating.
•
Use nonflammable cleaners.
•
Keep flammable materials and vapors, such as gasoline, away from
appliances.
•
Use two or more people to move and install appliance.
Proper disposal of an old appliance:
DANGER! Risk of child entrapment!
Old appliances can represent a suffocation hazard to children.
• Remove doors from your old appliance.
• Leave shelves in place
so children cannot easily climb inside
If an old appliance contains refrigerants, it must be recycled by a licensed
or disposal company.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce t
he risk of fire, electric shock
when using your appliance, follow these basic precautions:
We have provided many important safety messages in this manual and on your
You can be seriously injured or even killed if you don’t follow instructions.
Safety messages will tell you what the potential hazard is, how to reduce the
structions are not followed.
Keep flammable materials and vapors, such as gasoline, away from
Old appliances can represent a suffocation hazard to children.
so children cannot easily climb inside
.
If an old appliance contains refrigerants, it must be recycled by a licensed
service
IMPORTANT SAFETY INSTRUCTIONS
he risk of fire, electric shock
or injury
when using your appliance, follow these basic precautions:
4
Installation Instructions
Excessive Weight Hazard !
Use two or more people to move and install your appliance.
Failure to do so can result in back or other injury.
ALLOW APPLIANCE TO SIT
UPRIGHT FOR 24 HOURS BEFORE TURNING ON, TO
ALLOW THE COMPRESSOR LUBRICANT TO DRAIN.
1.
Remove packaging materials.
2.
Remove tape and glue residue from surfaces before turning on the appliance. Rub a
small amount of liquid dish soap over the adhesive with your f
ingers. Rinse with warm
water and dry.
3.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to
remove tape or glue. These products can damage the surface of your appliance.
4.
When Moving Your Appliance:
Your appliance is hea
vy. When moving the appliance for cleaning or service, be sure to
protect the floor. Always pull the appliance straight out when moving it. Do not wiggle or
“walk” the appliance when trying to move it, because floor damage can occur.
5.
Clean Before Using:
Af
ter you remove all of the packaging materials, clean the inside of your appliance
before using it. See cleaning instructions in Appliance Care.
6.
Some upright models have leveling legs. Level as necessary for best
operation.
7.
If your appliance has casters, after moving into place, lock the brakes on those casters
supplied with brakes. Always unlock before moving the appliance for cleaning.
Key Eject lock (some models):
To lock or unlock the appliance, you must hold the key in
the lock while turning. The lock is
spring loaded, so the key cannot be left in the lock.
If the key is lost, contact your dealer or SUMMIT APPLIANCE for a replacement. Always
give the model and serial number of your appliance when requesting a replacement
Keys for most models can be ordered online at
www.summitappliance.com/support
A NOTE ABOUT DOOR SWING:
Due to their wiring and controls, the doors on all MED2 units
cannot be reversed in the
field.
When ordering in the future, always specify whether you need a right hand or left
hand (option “LHD”) door swing. All units ship with a right hand door swing unless specified
differently at the time of order.
Use two or more people to move and install your appliance.
Failure to do so can result in back or other injury.
UPRIGHT FOR 24 HOURS BEFORE TURNING ON, TO
Remove tape and glue residue from surfaces before turning on the appliance. Rub a
ingers. Rinse with warm
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to
remove tape or glue. These products can damage the surface of your appliance.
vy. When moving the appliance for cleaning or service, be sure to
protect the floor. Always pull the appliance straight out when moving it. Do not wiggle or
“walk” the appliance when trying to move it, because floor damage can occur.
ter you remove all of the packaging materials, clean the inside of your appliance
If your appliance has casters, after moving into place, lock the brakes on those casters
supplied with brakes. Always unlock before moving the appliance for cleaning.
the lock while turning. The lock is
If the key is lost, contact your dealer or SUMMIT APPLIANCE for a replacement. Always
give the model and serial number of your appliance when requesting a replacement
key.
www.summitappliance.com/support
cannot be reversed in the
When ordering in the future, always specify whether you need a right hand or left
hand (option “LHD”) door swing. All units ship with a right hand door swing unless specified
5
Location Requirements
Keep flammable
materials and vapors, such as gasoline, away
from appliances. Failure to do so can result in fire, explosion or
death.
Location:
IMPORTANT:
Do not install the appliance near an oven, radiator, or other heat
source, nor in a location where the temperature w
ill fall below 40°F (5°C). Do not
place in direct sunlight.
Check the strength of the floor before installing your appliance. It should hold the
weight of a fully loaded appliance. Allow at least 4” (10
cm) of airspace at the top
and on both sides of the appliance and also 4
” between the back of the appliance
and the wall. If the appliance is going to be placed next to
a wall, leave extra
space on the hinge side so the door can open wider than its width.
NOTE: Allow 4” (10
cm) clearance at the top and sides and a ¼” (0.64 cm)
clearance between appliances.
IF YOUR MODEL HAS THE LETTERS “BI”
IN THE SUFFIX, IT IS DESIGNED FOR BUILT-IN USE
AND REQUIRE
ONLY
MINIMAL
CLEARANCES EXCEPT AT THE BACK
WHERE AT
LEAST 2” OF CLEARANCE SHOULD BE ALLOWED.
Electrical Shock Hazard
•
Plug into a grounded 3-prong outlet.
•
Do not remove ground prong.
•
Do not use an adapter.
•
Do not use an extension cord.
Failure to follow these instructions can result in fire,
electrical shock or
death.
Recommended grounding method:
A 115 Volt (AC only) 60 Hz grounded electrical supply with a 15-
or circuit breaker is required. It is recommended that a separate circuit serving
only your appliance be provided. Use
outlets that cannot be turned off by a
switch or pull chain. Do not use an extension cord.
materials and vapors, such as gasoline, away
from appliances. Failure to do so can result in fire, explosion or
Do not install the appliance near an oven, radiator, or other heat
ill fall below 40°F (5°C). Do not
Check the strength of the floor before installing your appliance. It should hold the
cm) of airspace at the top
” between the back of the appliance
a wall, leave extra
space on the hinge side so the door can open wider than its width.
cm) clearance at the top and sides and a ¼” (0.64 cm)
IF YOUR MODEL HAS THE LETTERS “BI”
AND REQUIRE
S
WHERE AT
electrical shock or
or 20- amp fuse
or circuit breaker is required. It is recommended that a separate circuit serving
outlets that cannot be turned off by a
6
Leveling your appliance (some models):
Locate the two front leveling legs that may be taped among the packing materials. (In
many models these legs are already mounted into the underside of the appliance.)
1. Screw these legs into the front holes on the bottom of the appliance. The back of
the appliance rests on two fixed supports. (Built-in models also have rear level
legs that can provide more precise leveling).
2. Adjust the front legs just enough to lift the cabinet up off the floor.
Note: If your model is equipped with front rollers, the front legs should be lowered
enough to lift the rollers off the floor to ensure the appliance does not roll
forward when the door is opened.
3. Place a leveling tool on top of the appliance, first side to side, then front to back.
Turn leg counter-clockwise to raise a corner. Turn leg clockwise to lower a corner.
4. Repeat Step 3 until appliance is level.
5. After appliance is fully loaded, recheck with level as in Step 3.
6.
If your appliance is equipped with casters, the two front casters have brakes to
prevent rolling. Keep brakes locked, and unlock for moving only.
When using the appliance:
In order to ensure proper temperature, you need to permit proper airflow in the
appliance. Do not block off any air vents. If the vents are blocked, airflow will be
hindered, and temperature and moisture problems may occur. Always position
contents to allow some airflow between shelves or baskets.
Allow the appliance to cool at least 6 to 8 hours before adding contents. Allow 24
hours for temperature to stabilize.
NOTE: When the appliance is first started, the compressor will run constantly until the
appliance is cooled. It may take 6 to 8 hours (or longer), depending on room
temperature and the number of times the appliance door is opened. After the
appliance has cooled, the compressor will turn on and off as needed to keep the
appliance at the proper temperature.
For optimum temperature performance, it is recommended that this unit be at
least 30% full during use. If you are only using this unit to store small loads, we
recommend adding some water bottles or freezer packs to ensure temperature
stability.
The outside of your appliance may feel warm. This is normal. The appliance’s design
and main function is to remove heat from packages and air space inside the
appliance. The heat is transferred to the room air, making the outside of the appliance
feel warm. (In some models the condenser that gets warm is just inside the side walls,
making these walls warm to the touch.)
ENERGY-SAVING TIPS
• The more airflow provided around an appliance, the less energy it will use.
• If your appliance requires manual defrosting, keep ice build-up to less than 1/2".
• Keep doors open a minimum of time, and shut securely.
7
Appliance Care
Defrosting:
Refrigerator models listed in this manual defrost automatically. However, freezer
models require manual defrosting. Before defrosting the unit, remove the contents of
the freezer, then set the thermostat to OFF (the compressor will stop working). Leave
the door open until ice and frost are completely melted. To speed up defrosting, you
can place a container of warm water (about 125°F) into the cabinet. Soak up the melt
water with clean toweling or a sponge and be sure the interior is dry before turning the
thermostat back to its normal setting.
• NOTE: It is not advisable to heat the interior of the freezer directly with hot water or
a hair dryer while defrosting since this can deform the cabinet
interior.
NEVER USE A METAL OBJECT TO REMOVE ICE FROM THE
REAR WALL. IF NEEDED, USE A PLASTIC ICE-SCRAPER.
Cleaning the appliance:
NOTE: To prevent the buildup of odors, clean the appliance about once a month.
Follow the procedure below for cleaning:
1. Disconnect from power.
2. Remove any parts that can be taken out of the cabinet, such as drawers.
3. Using a clean sponge or soft cloth, hand wash, rinse and dry removable parts and
interior surfaces thoroughly. Use a mild detergent in warm water. DO NOT use
abrasive or harsh cleansers such as window sprays, scouring cleansers,
flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers
containing petroleum products. DO NOT use harsh cleaning tools such as paper
towels or scouring pads, as these can scratch or damage the surfaces of the
refrigerator.
4. For stainless steel and painted metal exterior surfaces, use a clean sponge or soft
cloth and a mild detergent in warm water. DO NOT use abrasive or harsh
cleaners, or cleaners containing chlorine, as these can scratch or damage the
material. Using a soft cloth, dry thoroughly.
5. To help with removing odors, you can use a mixture of warm water and baking
soda (2 tbs to 1 qt of water) to wash the interior walls.
6. After cleaning, replace all of the parts that were removed from the appliance.
7. The condenser coils, located on the back or behind the base grille, should also be
cleaned regularly. This may be as often as every other month. Cleaning the
condenser coils can help reduce how much energy the appliance uses. When the
condenser coils are dusty or dirty, use a vacuum cleaner with an extension
attachment.
8. After cleaning the appliance, plug in or reconnect power.
NOTE: For CSS Models (completely stainless steel), only use cleaners
especially made for stainless steel.
8
Changing the light
bulb (some models only):
NOTE: Not all appliance bulbs will fit your appliance. Be sure to replace the bulb
with one of the same size, shape, base size and wattage. You can purchase
bulbs from www.summitappliance.com/support
1. Unplug appliance or disconnect power.
2. Remove the light shield. Most models do not require tools.
3. Replace the light bulb with an appliance bulb of the same wattage.
Replacement LED bulbs are available from our parts department.
4. Replace the light shield.
5. Plug in appliance or reconnect power.
Loss of power:
In the event of power loss, unplug the appliance. Once power is restored, allow
30 minutes for the refrigeration system to equalize. During this time, keep the
door closed as much as possible.
Remember: A full appliance stays cold longer than a partially filled one.
Moving the appliance:
1. Remove stored items and tape shelves, drawers and trays in place.
2. Unplug the appliance.
3. Clean it thoroughly.
4. Tape the appliance shut and tape the electrical cord to the cabinet.
When you get the appliance to its new location, refer to the Installation
Instructions and Temperature Selection sections for information on installation
and setting the controls.
9
Temperature Selection & Monitoring
Digital Thermostat
Temperature Parameters:
MED2 all-refrigerators come with digital thermostats that are preset at 4ºC, with a
range of 2º to 8ºC.
VT65MLBIMED2 and VT65MLBIMED2ADA all-freezers are preset to -20º, with a
range of -25º to -10ºC.
All other MED2 all-freezers are preset to -18ºC, with a range of -20º to -10ºC.
If you find it necessary to change the temperature setting for your digital thermostat,
please refer to the following instructions.
How to Adjust the Temperature:
To see the SET POINT:
The default display for your digital thermostat is the internal cabinet temperature. To
view the unit’s set point, push and immediately release the SET key. The display will
flash, showing the set point value. If no other actions are taken in 6 seconds, the
display will revert to the internal air temperature.
To change the SET POINT:
While the set point value is blinking, press the UP or DOWN arrow to change the set
point to your desired temperature. Press the SET button again to exit the adjustment.
The display will revert to the internal air temperature. PLEASE NOTE: The
temperature displayed on the digital thermostat is the internal air temperature. Your
alarm/thermometer (installed on the left in the control panel) provides a temperature
readout based on the buffered probe in order to better simulate the temperature of
what is actually stored inside the unit (as opposed to the air temperature itself). As a
result, these readings may not always display the same temperature reading.
NOTE:
The minimum and maximum range of your thermostat is preset and
locked by us, so it cannot easily be accidentally moved outside of the
recommended temperature ranges.
Note: details may
vary from image
10
Thermometer/Alarm
Every MED2 unit is equipped with a NIST calibrated Thermometer/Alarm that
simultaneously displays minimum, maximum, and current interior temperatures and
provides a visual and audible signal when the temperature inside the unit falls outside
the set temperature range.
NOTE ABOUT CALIBRATION: All MED2 units ship with a two-year certificate of
calibration in the alarm/thermometer box that comes inside your unit. Keep this
certificate stored safely for your records. Accucold offers re-calibration services
through their ISO 17025:2005 certified calibration laboratory. It is recommended to
have your probe re-calibrated every two years (or one year, depending on your state’s
health department guidelines). For more information on how to have your device re-
calibrated, contact us at [email protected]m.
The temperature sensor, or probe, is enclosed in a glycol-filled bottle that is stored
inside your unit in a special shelving compartment.
In some units, the center shelf is fixed in place and
cannot be removed (see image). This is because the
glycol-filled bottle that contains the temperature
sensors for your alarm and thermometer is best
stored in this location. The center of your refrigerator
or freezer will provide the most accurate
temperature readings. For proper temperature
monitoring, keep the bottles in place and do not
remove this shelf.
Note: Details may
vary from image
11
Thermometer/alarm instructions (cont’d):
Function of Controls:
MODE/RESET Key: Press ONCE to reset Max/Min temperature record. When the unit
is sounding an alarm, press ONCE to turn off the beeping sound.
HI/LO Key: Press ONCE to display high alarm setting. Press TWICE to display low
alarm setting. Press THREE TIMES to display current temperature reading.
ºF/ºC Key: Press this button to change the temperature display scale from Fahrenheit
(ºF) to Celsius (ºC).
Battery Installation: Remove battery compartment cover located on the rear of the
unit and remove insulation strip from battery compartment. Following the polarity
(+/-) diagram in the battery compartment, install the battery. Replace the battery
cover. The unit will beep and all segments of the LCD will be activated.
Programming the Alarms:
The thermometer displays the internal temperature of the unit being monitored, as
well as the maximum and minimum temperatures reached. The maximum and
minimum readings reflect the highest and lowest temperatures since the battery was
inserted or since the MODE/RESET key was last pressed. If the temperature rises
above or falls below the set temperature range, the alarm will sound. By default, the
high alarm temperature setting is 8°C (46.4°F) and the low alarm temperature setting
is 2°C (35.6°F). To reset these limits, follow these instructions:
High Alarm Temperature Setting: Press the HI/LO key ONCE, then press
MODE/RESET to enter the High Alarm temperature setting mode. Use the Up and
Down arrows to adjust the temperature accordingly. Press MODE/RESET once
again to confirm the setting.
Low Alarm Temperature Setting: Press the HI/LO key TWICE, then press
MODE/RESET to enter the Low Alarm temperature setting mode. Use the Up and
Down arrows to adjust the temperature accordingly. Press MODE/RESET ONCE to
confirm the setting.
By default, the low and high alarms should be audible. To turn alarms on/off:
Audible High Alarm Setting: To make sure the high alarm is audible, press HI/LO key
ONCE (to activate HI-SET on the screen). Then press the ALERT ON/OFF key
ONCE to activate the HIGH-ALARM beeping sound. Press again to deactivate.
Audible Low Alarm Setting: To make sure that the low temperature alarm is audible,
press the HI/LO key TWICE to activate LOW-SET on the screen. Then press the
ALERT ON/OFF key ONCE to activate the LOW-ALARM beeping sound. Press
again to deactivate.
NOTE: Set high and low alarm temperature limits above and below the refrigerator/
freezer operating temperature to prevent false alarms. For operating
temperature ranges, see Temperature Parameters on page 9.
NOTE: For an activated high alarm and low alarm buzzer, the display should
indicate HI-ALARM and LO-ALARM (see illustration on previous page).
More details about the features and usage of the Thermometer/Alarm can be
found in the User Manual accompanying the unit.
12
Keypad Lock
(optional on most models)
Factory-set default password: The factory-set default password is 0123. If the default
password is lost, press the key (located inside the battery box) for
30
seconds, then wait for the warning sound which signifies the factory-set
default password has been restored.
To set the password: While door is open, press the key (located
inside the battery box) until it jingles, enter the 0123 password, then #
within 10 seconds to confirm. Enter your password (1-16 digits), then
press # again to confirm. A total of 10 passwords can be set.
NOTE: Each password starts with a number from 0 to 9 in order. The first password starting
with 0 is the default password. For example, use 1xxx, then 2xxx etc. for 10 users.
Changing password: While the door is open, press the key (located inside the battery
box) until it jingles, enter the old password and press # within 10 seconds to confirm. Enter
the new password, then press # to confirm.
NOTE: The first digit cannot be changed.
To open the door: While the door is closed, press the START/END
key, enter the
password, then press START/END
again to confirm.
To lock door manually: Press #.
Function setting of automatic lock: Setting of the auto-lock time: Press the key
(inside the battery box), enter a number (any number between 10-99), then press # to
confirm. The auto-lock time can be set between 10-99 seconds after opening the door. If
the time is set less than 10 seconds, the door will not lock automatically, only manually.
Deleting the door-opening passwords: Press the START/END
key, enter default
password followed by 0000, then press # and all the door-opening passwords will be
deleted except for the default password.
NOTE: To access the battery box you need to remove only the two small screws on the top
and bottom of that cover. Do not remove the 4 screws holding the keypad and cover to
the appliance door.
About the Fixed Shelf
13
Operation of Specific Models
All-Refrigerators: FF24LMED2, FF28LWHMED2, FF511LBIMED2, FF511LBI7MED2,
FF511LBIMED2ADA, FF511LBI7MED2ADA, FF7LBIMED2, FF7LBIMED2ADA,
FFAR10MED2, SCR600LBIMED2, SCR600LBIMED2ADA
These models are all-refrigerators (no freezer compartment) with automatic defrost. All
have cold plates on the rear wall, and the coldest spots in the refrigerator will be in the rear
and toward the bottom. All have interior fans to promote even cooling. In the rear bottom
above the step, there is a drain line to allow defrost water to exit the refrigerator. Keep this
drain line clear, or icing inside the refrigerator will occur. FF7, FF511L, FFAR10, and SCR
series models have lights that are not door-activated, and are controlled either by a rocker
switch on the top right or a light switch inside. The light inside these units will stay on until
switched off manually. While LED lighting will not generate heat, it is not recommended to
leave the light on for long periods of time.
NOTE: Models with BI in the model number are designed for built-in operation and need
very little clearance on the sides and above the units. All other models require at least 4
inches of airflow on the sides and above the units. All models, including built-in units,
operate best when 2 inches is provided between the rear wall and the back of the unit.
All-Freezers: FS24LMED2, FS24L7MED2, FS30LMED2, FS30L7MED2, FS407LBIMED2,
FS407LBI7MED2, FS407LBIMED2ADA, FS407LBI7MED2ADA, VT65MLBIMED2,
VT65MLBIMED2ADA, VT65MLBI7MED2, VT65MLBI7MED2ADA
These are manual defrost all-freezers. No internal fans are present, and ice will build up
along the cooling coils. Periodically defrost the ice (recommended when the ice level
reaches a thickness of 1/4 to 1/2 inch). NEVER USE A METAL INSTRUMENT as you can
damage the cooling coils, which will void your warranty and often cannot be repaired.
Before defrosting the unit, remove the contents of the freezer, then set the thermostat
to OFF (the compressor will stop working) and disconnect the power. Leave the door
open until ice and frost are completely melted. To speed up defrosting, you can place
a container of warm water (about 125°F) into the cabinet. Soak up the melt water with
clean toweling or a sponge and be sure the interior is dry before turning the
thermostat back to its normal setting.
For built-in (BI) models and clearance information, see NOTE above.
14
Troubleshooting
Try these solutions first to avoid the cost of an unnecessary service call.
PROBLEM: The appliance is not operating.
• Is the power supply cord unplugged? Plug into a grounded 3-prong outlet.
• Has a fuse blown or a circuit breaker been tripped? Replace the fuse or reset
the circuit.
• Is the thermostat incorrectly set? See How to Adjust the Temperature on
page 9.
PROBLEM: The motor is constantly running, or running too much
•
Is it hotter than usual where the appliance is located? At normal temperatures,
the motor will typically run between 40% and 80% of the time. The motor will
run even longer when the unit is in an unusually warm environment.
•
Have a large number of items been added to the appliance? The more that is
added, the longer it will take for the unit to cool down. During this process, the
motor will run longer.
•
Is the door frequently opened? Warm air entering the appliance causes the
motor to run longer. Keep the door closed as much as possible.
•
Is the thermostat set correctly? See How to Adjust the Temperature on page 9.
•
Is the door completely closed? Push the door firmly shut.
•
Are the condenser coils dirty? This prevents proper air transfer, and causes the
motor to work harder. Clean the condenser coils. See Cleaning the Appliance
on page 7, and refer to #7.
•
Does the unit have proper clearance? Models with “BI” in their name require 2”
of rear clearance and minimal clearance on the sides and top. All other units
require at least 4” of clearance on all sides for proper operation.
PROBLEM: The temperature in the cabinet is too warm
•
Have you just added a large number of items to the appliance? This will warm
the interior of the unit until it is able to cool down to the correct temperature.
•
Is the thermostat set correctly? See How to Adjust the Temperature on page 9.
PROBLEM: There is excessive moisture inside the appliance
•
Is the door opened frequently? If so, humidity from the room will enter the
appliance and cause moisture to build up. This will happen even more if the air
in the room is very humid.
PROBLEM: The door is hard to open
•
Is the door gasket dirty or sticky? Clean the gasket and the surfaces that it
touches. Rub a thin coat of paraffin wax on the gasket after cleaning.
15
Limited Warranty
2-YEAR LIMITED WARRANTY FOR APPLIANCE
Within the 48 contiguous United States, for two years
from the date of purchase, when this appliance is
operated and maintained according to instructions attached to or furnished with the product, warrantor
will pay for factory-specified parts and repair l
abor to correct defects in materials or workmanship.
Service must be provided by a designated service company. Outside the 48 states, all parts are
warranted for two years
from manufacturing defects. Plastic parts, shelves and cabinets are warranted
to be
manufactured to commercially acceptable standards, and are not covered from damage during
handling or breakage.
5-YEAR COMPRESSOR WARRANTY
1. The compressor is covered for 5 years.
2. Replacement does not include labor.
ITEMS WARRANTOR WILL NOT PAY FOR:
1.
Service calls to correct the installation of your appliance, to instruct you how to use your appliance,
to replace or repair fuses or to correct wiring or plumbing.
2.
Service calls to repair or replace appliance light bulbs or broken glass shelves. Consumabl
(such as filters) are excluded from warranty coverage.
3.
Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products
approved by warrantor.
4.
Replacement parts or repair labor costs for units operated outside the United States.
5.
Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. The removal and reinstallation of your appliance i
f it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES –
LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN.
IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR. WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW TH
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
The following warning is required for goods sold in the state of California:
FELIX STORCH, INC.
770 Garrison Avenue
Bronx, New York 10474
Phone: (718) 893-3900
Fax: (844) 478-8799
www.summitappliance.com
For
parts and accessory ordering,
troubleshooting and helpful hints,
www.summitappliance.com/support
WARNING: This product can expose you to chemicals including Nickel (Metallic)
which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov
Note: Nickel is a component in all stainless steel and some other metal components.
from the date of purchase, when this appliance is
operated and maintained according to instructions attached to or furnished with the product, warrantor
abor to correct defects in materials or workmanship.
Service must be provided by a designated service company. Outside the 48 states, all parts are
from manufacturing defects. Plastic parts, shelves and cabinets are warranted
manufactured to commercially acceptable standards, and are not covered from damage during
Service calls to correct the installation of your appliance, to instruct you how to use your appliance,
Service calls to repair or replace appliance light bulbs or broken glass shelves. Consumabl
e parts
Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products
not
Replacement parts or repair labor costs for units operated outside the United States.
Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
f it is installed in an inaccessible location or is not
LIMITATION OF REMEDIES
PRODUCT REPAIR AS PROVIDED HEREIN.
IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR. WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW TH
E
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY
YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
The following warning is required for goods sold in the state of California:
parts and accessory ordering,
troubleshooting and helpful hints,
visit:
www.summitappliance.com/support
December 2018
WARNING: This product can expose you to chemicals including Nickel (Metallic)
Note: Nickel is a component in all stainless steel and some other metal components.
16
Si vous avez besoin de service ou appelez avec une question,
veuillez avoir cette information prête. Conservez ce Mode
d'emploi en votre possession.
Modèle :
_______________
Nᵒ de série :
_________________
Options ajoutées : ____________________________
Date d'achat : ______________________
Marchand : ________
Pour les pièces: visitez notre site Web
www.summitappliance.com/support
Série MED2
RÉFRIGÉRATEURS ET CONGÉLATEURS DE
STOCKAGE MÉDICAL ET DE LABORATOIRE
FELIX STORCH, INC.
ISO 9001:2015 inscrit
770 Garrison Avenue
Bronx, New York 10474
accucold.com
MODE D’EMPLOI
17
Tous-réfrigérateurs
•
FFAR24LMED2
Tout-réfrigérateur compact avec fonction de dégivrage automatique
•
FF28LWHMED2
Tout-réfrigérateur pour haut de comptoir avec dégivrage automatique
•
FF511LBIMED2 / FF511LBIMED2ADA
Tout-réfrigérateur sous-comptoir avec opération de dégivrage automatique
•
FF511LBI7MED2 / FF511LBI7MED2ADA
Tout réfrigérateur sous-comptoir commercial avec fonction de dégivrage
automatique
•
FF7LBIMED2 / FF7LBIMED2ADA
Tout-réfrigérateur sous-comptoir avec opération de dégivrage automatique
•
FFAR10MED2
Tout-réfrigérateur format de taille moyenne avec dégivrage automatique
•
SCR600LBIMED2 / SCR600LBIMED2ADA
Tout-réfrigérateur sous-comptoir avec porte vitrée et dégivrage automatique
Tous-congélateurs:
•
FS24LMED2
Tout-congélateur compact avec dégivrage manuel
•
FS24L7MED2
Tout-congélateur compact commercial avec fonction de dégivrage manuel
•
FS30LMED2
Tout-congélateur pour haut de comptoir avec dégivrage automatique
•
FS30L7MED2
Tout-congélateur commercial pour haut de comptoir avec fonction de dégivrage
manuel
•
FS407LBIMED2 / FS407LBIMED2ADA
Tout-congélateur sous-comptoir avec opération de dégivrage manuel
•
FS407LBI7MED2 / FS407LBI7MED2ADA
Tout-congélateur sous-comptoir commercial avec fonction de dégivrage manuel
•
VT65MLBIMED2 / VT65MLBIMED2ADA
Tout-congélateur sous-comptoir avec opération de dégivrage manuel
•
VT65MLBI7MED2 / VT65MLBI7MED2ADA
Tout-congélateur sous comptoir commercial avec fonction de dégivrage manuel
Numéros de modèles
18
Table des matières
Numéros de modèles .............................................................. 17
Sécurité de l'appareil ............................................................... 19
Mise au rebut appropriée d'un ancien appareil ................... 19
Instructions d’installation ...................................................... 20
Verrou d'éjection de clé ....................................................... 20
Conditions d'emplacement ............................................. 21 – 22
Emplacement ..................................................................... 21
Méthode de mise à terre recommandée ............................. 21
Mise à niveau de votre appareil .......................................... 22
Lors de l'utilisation de l'appareil .......................................... 22
Conseils d'économie d'énergie ........................................... 22
Entretien de l'appareil ..................................................... 23 – 24
Dégivrage ........................................................................... 23
Nettoyage de votre appareil ................................................ 23
Changer l'ampoule .............................................................. 24
Perte de courant ................................................................. 24
Déplacer l'appareil............................................................... 24
Sélection de la température et surveillance ................. 25 – 27
Thermostat numérique ........................................................ 25
Thermomètre / alarme ................................................. 26 – 27
Verrouillage du clavier ............................................................ 28
Fonctionnement de modèles spécifiques ............................. 29
Dépannage .............................................................................. 30
Garantie limitée ........................................................................ 31
19
Sécurité de l'appareil
Votre sécurité et la sécurité des autres sont très importantes pour nous.
Nous avons fourni de nombreux messages de sécurité importants dans ce manuel et sur
votre appareil. Toujours lire et obéir à tous les messages de sécurité.
Vous pouvez être sérieusement blessé ou même tué si vous ne suivez pas les instructions.
Les messages de sécurité vous diront ce qui est le danger potentiel, comment réduire le
risque de blessure et ce qui peut arr
iver si les instructions ne sont pas suivies.
• Branchez dans une prise à trois broches reliée à la terre.
•
Ne retirez pas la broche de mise à la terre et n'utilisez pas d'adaptateur 3/2.
• N'utilisez pas de rallonge.
•
Veillez à ne pas brancher dans les prises contrôlées par des interrupteurs
• Débranchez l'alimentation avant de faire l'entretien.
•
Après l'entretien, remplacer toutes les pièces et tous les panneaux avant d’utiliser.
• Utiliser des nettoyants ininflammables.
• Gardez les matériaux et les vapeurs inflammables, tels que l'essen
ce, loin des
appareils.
• Utilisez deux personnes ou plus pour déplacer et installer l'appareil.
NOTE: Les réfrigérateurs à tiroirs sont fournis avec des supports anti-
bascule. Toujours
installer avant l'utilisation.
Mise au rebut appropriée d'un ancien appareil:
DANGER! Risque de piégeage des enfants!
Les vieux appareils peuvent représenter un risque d'étouffement pour les
enfants.
• Enlever les portes de votre ancien appareil.
•
Laissez les étagères en place afin que les enfants ne puissent pas
facilement à l'intérieur.
Si un ancien appareil contient des réfrigérants, il doit être recyclé par un service agréé
ou une société d'élimination.
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT: pour réduire les risques d'incendie,
d'électrocution ou de blessures lors de l'utilisation
de votre appareil, suivez ces précautions de
base:
Nous avons fourni de nombreux messages de sécurité importants dans ce manuel et sur
Vous pouvez être sérieusement blessé ou même tué si vous ne suivez pas les instructions.
Les messages de sécurité vous diront ce qui est le danger potentiel, comment réduire le
iver si les instructions ne sont pas suivies.
Ne retirez pas la broche de mise à la terre et n'utilisez pas d'adaptateur 3/2.
Veillez à ne pas brancher dans les prises contrôlées par des interrupteurs
muraux.
Après l'entretien, remplacer toutes les pièces et tous les panneaux avant d’utiliser.
ce, loin des
bascule. Toujours
Les vieux appareils peuvent représenter un risque d'étouffement pour les
Laissez les étagères en place afin que les enfants ne puissent pas
grimper
Si un ancien appareil contient des réfrigérants, il doit être recyclé par un service agréé
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT: pour réduire les risques d'incendie,
d'électrocution ou de blessures lors de l'utilisation
base:
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
AccuCold SCR600LBIMED2ADA Manuel utilisateur
- Catégorie
- Frigos
- Taper
- Manuel utilisateur
