Best WPP9E42SB Guide d'installation

In USA - BEST Hartford, Wisconsin

In CANADA - BEST Drummondville, QC, Canada

Model WPP9

ENGLISH........................................3

FRANÇAIS...................................25

ESPAÑOL.....................................49

REGISTER YOUR PRODUCT ONLINE AT : www.BestRangeHoods.com/register

For additional Information visit www.BestRangeHoods.com

- 3 -

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel to

prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all

applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s

guidelines and safety standards such as those published by the National Fire Protection Associa-

tion (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only steel ductwork.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk

of electrical shock by providing an escape wire for the electric current.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

Do not use an extension cord. Have a qualified electrician install an outlet near the appliance.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambe’).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

!

INTENDED FOR DOMESTIC COOKING ONLY

!

- 4 -

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

!

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust

air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and

vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes

overheated. The motor will restart when it cools down. If the motor continues to shut off and restart,

have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be a minimum of 24" and a

maximum of 36" above the cooking surface.

9. Two installers are recommended because of the large size and weight of this hood.

10. This product is equipped with a thermostat which may start blower automatically. To reduce the

risk of injury and to prevent power from being switched on accidentally, switch power off at service

panel and lock or tag service panel.

11. Please read specification label on product for further information and requirements.

12. EXTERNAL BLOWER MODELS ONLY: To reduce risk of fire and electric shock, install this range

hood only with Best Exterior Blower Models EB6, EB9, EB12 or EB15 or Best In-Line Blower

Models ILB3, ILB6, ILB9 or ILB11. Other blowers cannot be substituited. (Blower sold separately)

- 5 -

CLEANING AND MAINTENANCE

Proper maintenance of the Range Hood will assure proper performance of the unit.

Motor

The motor is permanently lubricated and never needs oiling. If the motor bearings make

excessive or unusual noise, replace the motor with the exact service motor. The impeller

should also be replaced.

Grease Filter

The grease filters should be cleaned frequently. Use a warm detergent solution. Grease

filter are dishwasher safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration

of the filter may occur if using phosphate detergents, or as a result of local water

conditions - but this will not affect filter performance. This discoloration is not covered by

the warranty. See “INSTALL FILTERS” section for removal and installation instructions.

Drip Tray

The drip tray should be cleaned once a month or

as needed. To remove the drip tray, first remove

the baffle grease filters. Grasp both ends of the

drip tray. Gently lift the drip tray up until the bottom

of it clears the track. Pull the drip tray forward,

being careful not to spill the contents, and move it

to a nearby trash receptacle. To clean the drip tray,

drain and wipe all excess grease with a dry paper

towel. Wash with warm soapy water or in the

dishwasher. Dry with a clean cloth. To replace the

drip tray, lift it up and into the track on the hood.

Reinstall baffle grease filters.

Non-ducted Recirculation Filter

The non-ducted recirculation filter should be

changed every 6 months. Replace more often if

your cooking style generates extra grease, such as

frying and wok cooking. See “INSTALL FILTERS”

section for removal and installation instructions.

Stainless Steel Cleaning

DO:

• Regularly wash with clean cloth or rag

soaked with warm water and mild soap or

liquid dish detergent.

• Always clean in the direction of original

polish lines.

• Always rinse well with clear water (2 or 3

times) after cleaning. Wipe dry completely.

• You may also use a specialized

household stainless steel cleaner.

DON’T:

• Use any steel or stainless steel wool or

any other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction

residues reach the hood. During

construction/renovation, cover the range

hood to make sure no dust sticks to the

stainless steel surface.

Avoid: When choosing a detergent

• Any cleaners that contain bleach will attack stainless steel

• Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol,

etc., are highly explosive and should never be used close to a range.

- 6 -

OPERATION

A

C

B

D R

Button A = turns the lights on/low/high/off.

Button B = Activates/Deactivates the delay-off feature. Press once (when blower is on) to

activate the delay-off feature. The selected speed level that is displayed in display “C” will

blink when this feature is activated. After 10 minutes, the blower will then turn off. Delay

can be deactivated at any time by pressing the button again.

Display C = Indicates the selected speed of the blower 1, 2, 3, or b for boost.

“-” indicates the need to clean the grease filter or replace the non-duct filter.

Button D = Turns on the blower. Hood will turn on to the last speed selected. The blower

speed will change each time the button is pushed (from 1 to “b”). To turn the blower off,

press and hold button for approximately 2 seconds.

Button R = Filter clean indicator reset. Press and hold for 2 seconds to reset the indicator.

Auto Shut-Off Feature

If the blower and/or the lights are on continuously for 10 hours without any user interaction

with the controls, the hood will automatically shut off. Press any control button to re-activate

the hood.

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that

will turn on or speed up the blower if it senses excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF.

When this occurs, it is impossible to turn the blower OFF with its switch. If you must

stop the blower, do it from the main electrical panel.

Controls (Fig.1)

HALOGEN BULBS

This range hood requires 3 or 4 halogen bulbs (based

on size of hood) (Type T4, 120 Volt, 25 Watt Max, G9

Base).

WARNING: Always switch off the electrical

supply before carrying out any operation on the

appliance.

To change bulbs:

1. Open the cover by gently prying from proper slots

(Fig.2).

2. Remove the bulb by pulling sideways (DO NOT

ROTATE).

CAUTION: Bulb may be hot.

3. Replace with Type T4, 120 Volt, 25 Watt Max, G9 Base halogen bulbs. Do not touch

replacement bulbs with bare hands!

!

FIG. 2

- 7 -

PREPARE THE HOOD

Unpack hood and check contents.

You should receive:

1 - Hood

1 - Decorative Flues

1 - Parts Bag (B080810995) containing:

1 - Flue Mounting Bracket Set

2 - Mounting Screws (3,9 x 6mm Flat Head)

2 - Mounting Screws (3,9 x 9,5mm Pan Head)

4 - Mounting Lag Screws (6 x 60mm)

2 - Mounting Screws (4,8 x 38mm Pan Head)

2 - Drywall Anchors

1 - Installation Instructions

FLUE MOUNTING

BRACKET SET

2 MOUNTING SCREWS

(4,8x38mm Pan Head)

DECORATIVE

FLUES

2 MOUNTING

SCREWS

(3,9x9,5mm

Pan Head)

2 DRYWALL

ANCHORS

4 MOUNTING LAG

SCREWS (6x60mm)

2 MOUNTING

SCREWS

(3,9x6mm

Flat Head)

FIG. 3

- 8 -

EXTERIOR AND IN-LINE BLOWER SELECTION WPP9E Series

CAUTION: To reduce risk of fire and electric shock, install this range hood only with Best

Exterior Blower Models EB6, EB9, EB12 or EB15, and Best In-Line Blower Models ILB3, ILB6,

ILB9 or ILB11. Other blowers cannot be substituited.

The blower must be UL listed for Canadian and U.S. use, and evaluated for use with solid state

speed control, rated 120V, 60 Hz, 6.0 A max.

HOOD

24” TO 36” ABOVE

COOKING SURFACE

DECORATIVE

FLUE

10” ROUND

DUCT

INSTALL THE DUCTWORK WPP9E Series

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the Exterior Blower or In-Line Blower will be mounted. See

illustrations below for mounting location suggestions and restrictions.

2. A straight, short duct run will allow the hood to perform most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as

few of them as possible. Larger ducting may be required for best performance with long

duct runs.

4. After the Exterior or In-Line Blower has been installed, connect round metal ductwork

and work back towards the hood location. Use duct tape to seal joints between ductwork

sections.

OK

SUGGESTED MOUNTING LOCATIONS

EXTERIOR BLOWER

CAUTION: MAY NOT FIT

UNDER EAVES OF SINGLE

STORY HOMES

EXTERIOR

BLOWER

10” ROUND

DUCT

EXTERIOR

BLOWER

10” ROUND

ELBOW

10”

ROUND

DUCT

FIG. 4

5 - 3/8”

CENTERLINE OF

DUCT TO WALL

- 9 -

IN-LINE BLOWER

FIG. 5

INSTALL THE DUCTWORK

(WPP9IQ and WPP9IQT)

NOTE: To reduce the risk of fire, use only

metal ductwork.

1. Decide where the ductwork will run

between the hood and the outside.

2. A straight, short duct run will allow the hood

to perform most efficiently.

It is recommended that there be a minimum

of 6” of straight duct from to an elbow for 8”

duct and 12” for 10” duct.

3. Long duct runs, elbows, and transitions will

reduce the performance of the hood. Use

as few of them as possible.

4. Install a roof or wall cap. Connect 8" WPPIQ

(or 10” WPPIQT) round metal ductwork to

cap and work back towards hood location.

Use duct tape to seal the joints between

ductwork sections (Fig.6).

24” TO 36” ABOVE

COOKING SURFACE

ROOF CAP

WALL

CAP

8” OR 10” ROUND

ELBOW

HOOD

DECORATIVE

FLUE

8” OR 10” ROUND

DUCT

FIG.6

8” DUCT (5 - 1/8”)

10” DUCT (5 - 3/8”)

CENTERLINE OF

DUCT TO WALL

- 10 -

INSTALL THE HOOD

Remove the plastic protective film from all exterior

surfaces, decorative flues and filters, prior to final

installation

1. Construct wood wall framing that is flush with interior

surface of wall studs (Fig.7).

Make sure:

a) the framing is centered over installation location.

b) the height of the framing will allow the hood to be

secured to the framing within the dimensions shown.

2. Install the (2) 6 x 60mm screws for the top of the

hood at the dimensions shown in Fig.8-9. Use the

two outer keyhole slots, do not completely tighten

the screws.

3. Hang the hood onto the screws.

4. Level the hood and secure (2) 6 x 60mm screws at

the outer locations of the hood. Tighten all (4) screws.

Notes:

a. Minimum hood distance above cook top must not

be less than 24”. A maximum of 36” above cook top

is highly recommended for best capture of cooking

impurities. Distances over 36” are the installer and

user discretion.

FIG. 7

FRAMING BEHIND WOOD

CROSS SUPPORT

WOOD CROSS

SUPPORT BEHIND

DRYWALL

Ceiling

Height

Duct

Method

Hood Distance Above 36” High Cok Top (in.)

24

Mounting Bracket Center Hole Location Above 36” High Cook Top (in.) see Fig.7

25 26 28 29 30 31 32 33 34 35 36 27

44

1/4

45

1/4

46

1/4

48

1/4

49

1/4

51

1/4

52

1/4

53

1/4

54

1/4

55

1/4

56

1/4

47

1/4

50

1/4

X X X X X X X 8 Feet Ducted

Non-

Ducted

X X

X X X X X X

X* X* X* X X X X 9 Feet Ducted

Non-

Ducted

X X X X X X X

X X X X X X X X 10 Feet

(see note b)

Ducted

Non-

Ducted

X X

X X X X X X X X X X

X X X X X

11 Feet

(see note a & b)

Ducted

Non-

Ducted

X X X X X

X = Possible Installation Heights

X* = Possible Installation Heights but the Non-Duct Filter Slots will be exposed on

WPP9IQ36SB & WPP9IQ42SB

Notes:

a. Minimum hood distance above cook top must not be less than 24”. A maximum of

36” above cook top is highly recommended for best capture of cooking impurities.

Distances over 36” are at the installer and the users discretion; and if ceiling height

and flue lenght permit.

b. Requires optional 10’ flue extension, ducted model AEWPP9SB or non-ducted

model AEWPP9SBN.

- 11 -

MOUNTING LAG

SCREWS (6x60mm)

WALL

FRAMING

MOUNTING LAG

SCREWS (6x60mm)

FIG. 8

FIG. 9

- 12 -

WIRING (WPP9IQ and WPP9IQT)

Note: This range hood must be properly

grounded. The unit should be installed by a

qualified electrician in accordance with all

applicable national and local electrical codes.

1. Remove the wiring box cover. Remove a

knockout from the wiring box (Fig.10).

2. Secure the conduit to the wiring box through a

conduit connector.

3. Make electrical connections. Connect white to

white, black to black and green to green.

4. Replace wiring box cover and screws. Make sure

that wires are not pinched between cover and

box.

ADDITIONAL EXTERNAL

BLOWER WIRING (WPP9E)

1. Run 2-wire plus ground power cable from the

exterior blower to the hood’s wiring box marked

“motor connection” (Fig.11).

2. Remove the cover from the wiring box and

remove one knockout.

3. Feed 6” of cable through the knockout opening

and secure the cable to the wiring box with an

appropriate connector.

4. Make electrical connections at the hood.

Connect white-to-white, red-to-black and

green-to-ground.

5. Replace the wiring box cover and screws.

Make sure wires are not pinched between the

cover and box.

Exterior blower connection:

1. Make electrical connections at the exterior

blower (see instructions provided with the

exterior blower).

WIRING BOX

COVER

EXTERIOR BLOWER

BLOWER CONNECTION AT HOOD

BOX MARKED

“MOTOR

CONNECTION”

CONNECT:

WHITE-TO-WHITE,

RED-TO-BLACK,

GREEN-TO-GROUND.

FIG.11

FIG.10

- 13 -

MOUNTING SCREWS

(4,8x38mm)

MOUNTING SCREWS

(3,9x9,5mm Pan Head)

INSTALL FLUE MOUNTING

BRACKET

DUCTED AND NON-DUCTED

1.Assemble the flue mounting bracket,

adjusting outside width as shown. (Fig.12)

2.Carefully center the mounting bracket directly

over the range hood location.

3.Secure the bracket assembly to the ceiling

using (2) 4.8 x 38mm mounting screws and

drywall anchors (Fig.13). Make sure the

bracket is pushed into the corner, tight against

the wall if necessary, and centered over the

hood. Complete the installation.

DUCTED INSTALLATION ONLY

Note: Rooms with 10 or 11 foot ceilings

require flue extension model AEWPP9SB,

available from your local dealer. Discard

the upper flue supplied with the range

hood and replace it with the longer flue

extension.

1. Attach ductwork to damper/duct connector.

2. Run 8” WPPIQ or 10” WPPIQT & WPPE

diameter metal ductwork to the outside

location (Fig.14).

3. Install an appropriate wall or roof cap with

damper to exhaust the air to the outside.

4. Tape all duct joints with aluminum duct tape.

5. Install upper and lower decorative flues

onto the range hood. Vents are concealed

on 8-foot ceilings. Vents maybe exposed

on 9-foot ceilings (Fig.15).

6. Secure upper flue to flue mounting bracket

with (2) 3.9 x 6mm screws (Fig.16).

8" or 10” ROUND

METAL DUCT

DECORATIVE

FLUE

DUCT TAPE

CEILING

CONCEALED

VENTS

DRYWALL

ANCHORS

FIG. 12

FIG. 13

FIG. 14

FIG. 15 FIG. 16

- 14 -

NON-DUCTED INSTALLATION AVAILABLE

ONLY FOR SINGLE BLOWER VERSION

(WPP9IQ only)

Note:

a. Purchase Model ANKWPP9 Non-ducted

Recirculation Kit from your local dealer.

b. Rooms with 10 or 11 foot ceilings require

Flue Extension Model AEWPP9SBN,

available from your local dealer. Discard

the upper flue supplied with the range

hood and replace it with the longer flue

extension.

1. Attach the 6”-to-8” adapter to blower

discharge and tape joint with aluminum

duct tape (Fig.16).

2. Install the plenum to the upper decorative

flue using (4) 3.9 x 6mm flat head screws

provided as shown (Fig.17).

3. Attach 6” expandable ducting to the

plenum using the adapter and tape joints

with aluminum duct tape (Fig.18).

4. Slide upper flue into lower flue.

5. Attach flue assembly to hood.

6. Attach flex duct to plenum through the duct

connector (Fig.18).

7. Attach upper flue to flue bracket using (2)

3.9 x 6mm flat head screws.

MOUNTING SCREWS

(3,9x6mm Flat Head)

FIG. 16

FIG. 17

FIG. 18

DUCT

CONNECTOR

- 15 -

INSTALL FILTERS

DUCTED AND NON-DUCTED HOODS

1.To remove the GREASE filter, (Fig.19) push

the filter towards the front so that it clears

the filter channel, then pull down on the

handle to disengage the filter from the

hood. Tilt the filter downward and remove.

2.The grease filters and the drip tray (see

page 5 for removal & cleaning instructions)

should be cleaned frequently. Use a warm

detergent solution. Grease filters and the

oil collectors are dishwasher safe.

3.To install the GREASE filter, align rear filter

tabs with spring in the hood. Pull down

handle, push filter into position and release.

Make sure the filter is securely engaged

after installation.

NOTE: Prior to use, remove protective film

from the filter frame.

NON-DUCTED HOODS (SINGLE MOTOR

VERSION

WPP9IQ only)

1. Non-ducted recirculation filters not

included. They must be purchased

separately (ANKWPP9 Kit).

2. Using no.6 x 1/2” screws, install one filter

support on each side (provided) of the

internal blower (Fig.20).

3. Position each filter over its support, insert

both pins (B) into the round slot (C) on

filter side and rotate to lock in place

(Fig.21).

Non-ducted recirculation filters

The non-ducted recirculation filters should

be changed every 6 months. Rotate the filters

to remove and replace.

FIG. 19

FIG. 20

FIG. 21

- 16 -

CALIBRATE IQ BLOWER SYSTEM

TM

Ducted Internal Blower Hoods Only

After the hood is installed and wired, engage the calibration process (our Guaranteed

Performance System Technology) to ensure full-rated airflow is being delivered. Prior to

calibration, ensure that all filters, light bulbs and duct system components are installed and

sealed.

CALIBRATION PROCESS

Hold the calibration button for 3 seconds; calibration button will light up and stay on for up to

13 minutes. The blower will start and begin the calibration process. When calibration is

complete, one of two things will occur:

A.The blower turns off and calibration button light turns off = Successful calibration.

B.The blower turns off and calibration button light blinks continuously = Too much restriction

in the ductwork is preventing the IQ Blower System

TM

from achieving the rated airflow. The

blower is automatically set to maximum intensity.

Note: Common items that cause restrictions: restricted damper flap (backdraft damper, wall

cap, roof cap), too many elbows, duct size less than 80% of hood outlet, poor transition,

use of flex ducting and/or crushed ducting.

Two options are available:

1.Press the calibration button to accept airflow as is. The IQ Blower System

TM

is now configured

to its highest possible setting. The blinking calibration light goes out.

2.Correct duct restriction and repeat the calibration process.

a. To clear the original calibration data, hold calibration button for 10 seconds. The light

will blink 3 times to confirm and the blower configuration will go back to default settings.

b. Repeat calibration process.

CALIBRATION LIGHT

CALIBRATION

BUTTON

- 17 -

WARRANTY

ONE YEAR LIMITED WARRANTY FOR BEST PRODUCTS

Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products will be free

from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT ABILITY

OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found

to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT

BULBS, FUSE, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does

not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence,

accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recom-

mended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not

allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE PURCHASER'S

SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty

supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address stated below or telephone number stated below,

(b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of

requesting warranty service, you must present evidence of the original purchase date.

In USA - Best®, 926 W. State Street, Hartford, WI 53027 (800-558-1711)

In Canada - Best®, 550 Lemire Blvd., Drummondville, QC J2C 7W9 (866-737-7770)

www.BestRangeHoods.com

WPP9 Programming Mode Procedure

WPP9E Programming Mode Procedure

The range hood is designed to work with several different blowers models. Before using the

hood, the control must first be programmed to your blower model, in order to achieve proper

operating speed:

1.Find the SETUP number that corresponds to the blower model that is installed with your

range hood.

2.There must be power to the hood but the blower and lights must be turned off.

3.Push simultaneously LIGHT SWITCH and RESET SWITCH for 5 sec: the display shows a

“P” blinking three times and then shows alternately the “P” and the setup selected.

4.Select the desired setup with BLOWER SWITCH (3

Î2Î1) or RESET SWITCH

(1

Î2Î3).

5. Push TIMER SWITCH to confirm.

6. The display (“P”) blinks two times ( 2 sec on - 0,5sec off) recording the selected setup.

SETUP 1

SETUP 2

SETUP 3

EB6

ILB3

ILB6

EB12

EB15

ILB9

EB9

ILB11

Description of “Speed Level”

Setup 1 is for motors with a rating up to 3.0 amp

Setup 2 is for motors with a rating between 3.1 amp and 5.0 amp

Setup 3 is for motors with a rating greater than 5.1 amp

- 18 -

KEY NO. PART NO. DESCRIPTION

9 B08087951 Grease Filters

17 BE3351882 Light Diffuser Support 36”

17 BE3351898 Light Diffuser Support 42”

37 B02300804 Heat Sentry

67 B06102602 Wires Assembly

114 B32904990 Wire Clamp

115 BE3350233 Wiring Box

116 BE3334252 Wiring Box Cover

130 BE3405180 Front trim 36”

130 BE3405184 Front trim 42”

195 BE3351870 Filter Spacers 42” only

202 B03292290 Wire Clamp

274 B03295035 Fuse Box

415 B03292596 Fairlead

439 B02320034 Grommet

474 B02300918 Halogen Lamp

485 B08016372 Decorative Flue Assembly

506 97019432 BLDC Driver

507 B06102584 Calibration Button Assembly

* B080810995 Fitting Set (Includes Key No. 998)

AQI B06102596 Switch Box Assembly

ARU B08092501 Duct Connector Assembly 8”

IME B06145225 Electrical Installation Assembly

CAS B06002259 Blower Assembly

ANKWPP9 B08999177 Non-Ducted Kit (Includes Key No. 58, 86, 122, 503)

58 B03294170 Outlet Reduction

86 B03292300 Outlet Flange

122 B08093448 Riser

503 B02011557 Expandable Duct

AFCROUND2 99111455 Non-Duct Filter Supports

* Not shown assembled.

SERVICE PARTS

MODEL WPP9IQ

- 19 -

- 20 -

KEY NO. PART NO. DESCRIPTION

9 B08087951 Grease Filters

17 BE3351882 Light Diffuser Support 36”

17 BE3351898 Light Diffuser Support 42”

17 BE3351906 Light Diffuser Support 48”

17 BE3351915 Light Diffuser Support 54”

37 B02300804 Heat Sentry

67 B06102603 Wires Assembly 36” or 42”

67 B06102606 Wires Assembly 48” or 54”

114 B32904990 Wire Clamp

115 BE3350233 Wiring Box

116 BE3334252 Wiring Box Cover

130 BE3405180 Front trim 36”

130 BE3405184 Front trim 42”

130 BE3405187 Front trim 48”

130 BE3405190 Front trim 54”

195 BE3351870 Filter Spacers 42” and 54” only

202 B03292290 Wire Clamp

274 B03295035 Fuse Box

415 B03292596 Fairlead

439 B02320034 Grommet

474 B02300918 Halogen Lamp

485 B08016379 Decorative Flue Assembly

506 97019434 BLDC Driver

507 B06102584 Calibration Button Assembly

* B080810995 Fitting Set (Includes Key No. 998)

AQI B06102596 Switch Box Assembly

ARU BE3405192 Duct Connector Assembly 10”

IME B06145225 Electrical Installation Assembly

CAS B06002259 Blower Assembly

* Not shown assembled.

SERVICE PARTS

MODEL WPP9IQT

La page charge ...

Best WPP9E42SB Guide d'installation

Ce manuel convient également à

Best WPP9E42SB Guide d'installation

dans d''autres langues

Documents connexes