Inglis IST143301 Le manuel du propriétaire

Marque: Inglis

Modèle: IST143301

Catégorie: Frigos

Taper: Le manuel du propriétaire

REFRIGERATORUSE &CAREGUIDE

/ /

GUIDED'UTILISATIONETffENTRETIENDUREFRIGERATEUR

TableofContents/Tabledesmatibres

ASSISTANCE OR SERVICE ............................. 1

REFRIGERATOR SAFETY ............................... 1

INSTALLATION INSTRUCTIONS .................... 2

REFRIGERATOR USE ...................................... 9

REFRIGERATOR CARE ................................. 10

TROUBLESHOOTING .................................... 11

WAR RANTY .................................................... 13

ASSISTANCE OU SERVICE ........................... 14

SECURITE DU REFRIGERATEUR ................ 14

INSTR UCTIONS D'INSTALLATION .............. 15

UTILISATION DU RleFRIGleRATEUR ............ 23

ENTRETIEN DU RleFRIGleRATEUR .............. 25

DlePAN NAG E .................................................. 26

GARANTIE ....................................................... 26

Assistance or Service

If you need assistance or service, first see the "Troubleshooting"

section. Additional help is available by calling f-800-807-6777,

or write:

Whirlpool Canada LP

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Information may also be obtained by visiting our website at

www.inglis.ca.

Please include a daytime phone number in your correspondence.

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your appliance to help

you obtain assistance or service if you ever need it. You will need

to know your complete model number and serial number. You can

find this information on the model and serial number label, located

on the inside wall of the refrigerator compartment.

Dealer name

Serial number

Address

Phone number

Model number

Purchase date

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

2316213

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help avoid

accidents.

Before You Throw Away Your Old Refrigerator or Freezer:.

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Do not use sharp instruments, rubbing alcohol, flammable fluids,

or abrasive cleaners to remove tape or glue. These products can

damage the surface of your refrigerator. For more information, see

"Refrigerator Safety."

IMPORTANT: Do not remove the white foam air return insert from

behind the control panel on the ceiling of the refrigerator. If the

insert is removed, ice may migrate down from the freezer and

cause icicles to form.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/211

(12.70 mm) space on each side. Allow 3" (7.5 cm) of space

between overhead cabinets and refrigerator top. Allow at least 1"

(25.40 mm) between back of cabinet and the wall. Ifyour

refrigerator has an ice maker, make sure you leave some extra

space at the back for the water line connections.

• If you are installing your refrigerator next to a fixed wall, leave

2" (5.08 cm) minimum on the hinge side (depending on your

model) to allow for the door to swing open.

• Level the refrigerator. See "Adjust the Doors."

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install in a

location where the temperature will fall below 55°F (13°C).

3" (7.5crn) / °_

II I

_11I

2"(5.08cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Read all directions before you begin.

IMPORTANT:

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7/1611and 1/211open-end

wrenches or 2 adjustable wrenches, 1/4"nut driver and drill bit,

hand drill or electric drill (properly grounded). Gather the required

tools and parts before starting installation. Read and follow the

instructions provided with any tools listed.

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/_6"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207-827 kPa) is required to operate the ice maker. If you

have questions about your water pressure, call a licensed,

qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the ice maker is still not operating properly:

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualified plumber.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Connect to Refrigerator

NOTE: On kit models, assemble water valve to refrigerator per kit

instructions.

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Read all directions before you begin.

IMPORTANT: Ifyou turn the refrigerator on before the water line is

connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"to 11/4'' (1.27 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you will need. Measure

from the connection on lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"hole in the cold water pipe

you have selected.

G B

F E D v

A. Cold waterpipe E.Compression sleeve

B. Pipe clamp F. Shutoff valve

C. Copper tubing G.Packingnut

D. Compressionnut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

A. Tube clamp

B. Copper tubing

C. Compression nut

D. Valve inlet

The ice maker is equipped with a built-in water strainer. Ifyour

water conditions require a second water strainer, install it in

the 1/4"(6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Disconnect the tube clamp on the back of the product and

insert the copper tubing through the clamp as shown.

3. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown.

4. Tighten the compression nut. Do not overtighten. Reattach the

tube clamp and tube to the back of the cabinet.

A. Tubeclamp C. Compressionnut

B. Copper tubing

5. Turn shutoff valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

6. The ice maker is equipped with a built-in water strainer. Ifyour

water conditions require a second water strainer, install it in

the 1/4"(6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Completethe Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill ice container.

TOOLS NEEDED: %6"hex-head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, %6" open-end wrench, flat

2" putty knife.

IMPORTANT:

• Before you begin, turn the refrigerator control OFE Unplug

refrigerator or disconnect power.

• Remove food and adjustable door or utility bins from doors.

• If you are only removing and replacing the doors, see the

"Remove Doors and Hinges" and "Replace Doors and

Hinges" sections.

• Depending on your model, you may have standard (Style 1) or

contoured (Style 2) doors. If you are also going to reverse the

door swing, follow the instructions for the appropriate door

style.

Remove Doors and Hinges

"5/16"Hex-Head Hinge Screw

1. Unplug refrigerator or disconnect power.

2. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

4. Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

5. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open

in the opposite direction, follow these steps. Ifyou are not

reversing the doors, see "Replace Doors and Hinges."

Style I - Standard

Graphics follow these instructions.

DoorStop Screw

DoorHandle Sealing Screw

Flat-Head Handle Screw

DoorHinge Hole Plug

Cabinet Hinge Hole Plug

Door Handle Screw Cover

Door Handle Seal Screw Front Round-Head Handle Screw

Cabinet

1. Remove %6" hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and

move them to opposite side hinge holes as shown.

See Graphic 1-2.

Freezer door

f. Remove freezer handle assembly as shown. Keep all parts

together. See Graphic 2.

2. Remove door hinge hole plug. Move to opposite side as

shown. See Graphic 3.

3. Remove door handle sealing screws. Move to opposite side of

freezer door as shown. See Graphic 4.

4. Remove door stop. Move to opposite side of freezer door as

shown. See Graphic 5.

5. Position freezer handle on opposite side of freezer door.

Assemble handle on door as shown. See Graphic 2.

6. Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

Refrigerator door

f. Remove the screw cover. See Graphic 6.

2. Remove refrigerator handle assembly as shown. Keep all

parts together. See Graphic 6.

3. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown. See Graphic 3.

4. Remove door handle sealing screws. Move to opposite side of

refrigerator door as shown. See Graphic 4.

5. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown. See Graphic 7.

6. Remove door stop. Move to opposite side of refrigerator door

as shown. See Graphic 5.

7. Position refrigerator handle on opposite side of the refrigerator

door as shown. See Graphic 6. Drive top two screws in handle

first. Align lower portion of handle and drive bottom screw.

8. Replace screw cover. See Graphic 6.

9. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on refrigerator.

Style 2 - Contoured

Graphics follow these instructions.

Round-Head Door Handle

Handle Screw Screw Hole Plug

Door Hinge

Hole Plug

Cabinet

1. Remove %6" hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from the cabinet top and

move them to opposite side hinge holes as shown. See

Graphic 1-2.

Doors

1. Remove door hinge hole plug from top of freezer door. Move

to opposite side as shown. See Graphic 2.

2. Remove door stop from both the freezer and refrigerator

doors and move to the other side. See Graphic 3.

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

f. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten

all screws. See Center Hinge graphic. Replace the freezer

door.

3. Assemble the parts for the top hinge as shown. See Top Hinge

graphic. Do not tighten screws completely.

4. Line up the doors so that the bottom of the freezer door aligns

evenly with the top of the refrigerator door. Tighten all screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in

place. Reinstall top hinge cover. See Top Hinge graphic.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug in refrigerator or reconnect power.

3. Reset the controls. See "Using the Controls."

4. Return all removable door parts to doors and food to

refrigerator.

Style I - Standard

Center Hinge

A. Door Stop

B. Door Stop Screw

C. Spacer

D. Center Hinge

E. 5/_6"Hex-Head Hinge Screws

K Spacer

Bottom Hinge

A. Door Stop

B. Spacer

C. Door Stop Screw

D. Bottom Hinge

E. 5h6"Hex-Head Hinge Screws

A, Cabinet Hinge Hole Plugs

A. Door Hinge Hole Plug

A, Flat-Head Handle Screws

B. Freezer Handle

A. Door Handle Seating Screws

A. 5/_,, Hex-Head Hinge

Screws and Washers

*%.

A. Door Handle

Seal Screw Front

Style 2 - Contoured

Top Hinge

A. Top Hinge Cover

B. 5/_8"Hex-Head Hinge Screws

C. Top Hinge

D. Spacer

Center Hinge

A. Door Stop

B. Door Stop Screw

C. Spacer

D. Center Hinge

E. 5_6"Hex-Head Hinge Screws

K Spacer

Bottom Hinge

A. Door Stop

B. Spacer

C. Door Stop Screw

D. Bottom Hinge

E. b/_,,Hex-Head Hinge Screws

A. 5h_" Hex-Head Hinge

Screws and Washers

[]

A. Cabinet Hinge Hole Plugs

A. Door Hinge Hole Plug

Removal of Door Stops

A. Door Stop

B. Door Stop Screw

Reinstallation of Door Stops

A. Door Step

B. Door Stop Screw

Your refrigerator has two front adjustable rollers - one on the right

and one on the left. Ifyour refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the instructions below.

Depending on your model, your refrigerator may have leveling

legs (Style 1) or leveling screws (Style 2).They are part of the front

roller assemblies which are found at the base of the refrigerator on

either side.

1. Turn the leveling legs or leveling screws to the right to raise

that side of the refrigerator or to the left to lower that side. It

may take several turns to adjust the tilt of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

2. Open both doors again and be sure that they close as easily

as you like. If not, tilt the refrigerator slightly more to the rear

by turning both leveling screws to the right. It may take several

more turns, and you should turn both leveling screws the

same amount.

Style I

Style 2

3. Using a level, be sure that the refrigerator is still level side to

side, Readjust if necessary.

REFRIGERATORUSE

For your convenience, your refrigerator controls are preset at the

factory. When you first install your refrigerator, make sure that the

controls are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to

the word OFF or until the word OFF appears. Your product will not

cool when the refrigerator control is set to OFR

Mid-setting "3"

OFF

COLI£S @

£ I

IMPORTANT:

• Give your refrigerator time to cool down completely before

adding food, It is best to wait 24 hours before you put food

into the refrigerator.

• If you add food before the refrigerator has cooled completely,

your food may spoil. Adjusting the Refrigerator and Freezer

Controls to a higher (colder) than recommended setting will

not cool the compartments any faster.

Adjusting Controls

The mid-settings indicated in the previous section should be

correct for normal household usage. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the

chart below as a guide. On models with two controls, adjust the

refrigerator temperature first. Wait at least 24 hours between

adjustments and then recheck the temperatures.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR or

TEMPERATURE Control one

setting higher

FREEZER too warm/too FREEZER or TEMPERATURE

little ice Control one setting higher

MAX ice production switch

REFRIGERATOR too cold REFRIGERATOR or

TEMPERATURE Control one

setting lower

FREEZER too cold FREEZER or TEMPERATURE

Control one setting lower

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

Turning the Ice Maker On/Off

Toturn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Ice Production Rate

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period.

• To increase ice production, lower the freezer and refrigerator

temperature. See <<Usingthe Controls." Wait 24 hours

between adjustments.

• For maximum ice production (on some models), push the

switch to ICE PLUS. The ice maker should produce 16 to

20 batches of ice in a 24-hour period in the Ice Plus mode.

Remember

• The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice container and the dispenser

mechanism.

• Do not store anything on top of or in the ice maker or ice bin.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to keep odors

from building up. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash painted metal exteriors with a clean sponge or soft cloth

and a mild detergent in warm water. Dry thoroughly with a soft

cloth.

4. Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size, shape, and wattage.

Refrigerator Light

1. Unplug refrigerator or disconnect power.

2. Reach behind the control panel and unscrew the bulb.

3. Replace the bulb with a 40-watt appliance bulb.

4. Plug in refrigerator or reconnect power.

Freezer Light

1. Unplug refrigerator or disconnect power.

2. Remove the freezer shelf.

3. Remove the freezer light shield by pushing down.

4. Remove the light bulb and replace with one of the same size,

shape and wattage.

5. Replace the light shield.

6. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• Power cord unplugged? Plug into a grounded 3 prong outlet.

• Is outlet working? Plug in a lamp to see if the outlet is

working.

• Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker.

• Pulsating - fans/compressor adjusting to optimize

performance.

• Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator.

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle.

• Popping - contraction/expansion of inside walls, especially

during initial cool-down.

• Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan.

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

• Crisper cover in the way? Make sure the crisper cover is

pushed in fully, so that the back rests on the supports.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth,

The lights do not work

• Is a light bulb loose in the socket or burned out? See

"Changing the Light Bulbs."

Temperature istoo warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s} opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s} opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure,

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow, Straighten the water source line,

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure,

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof

packaging to store food.

• Are there minerals (such as sulfur) in the wate_ A water

filter may need to be installed to remove the minerals.

INGLIS®MAJORAPPLIANCEWARRANIT

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Canada LP (hereafter "Whirlpool") will pay for factory specification replacement parts and repair

labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM PROVINCE TO PROVINCE.

Outside Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help

can be found by checking the "Assistance or Service" section or by calling Whirlpool at 1-800-807-6777. 8/05

p p

GUIDED'UTILISATIONETD NTRETIENDUREFRIGERATEUR

Assistance ou service

Si vous avez besoin d'assistance ou de service, consulter d'abord

la section "Depannage". On peut obtenir de I'aide supplementaire

en appelant 1-800-807-6777, ou en ecrivant a :

Whirlpool Canada LP

Centre d'interaction avec la clientele

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Des informations peuvent egalement _tre obtenues en visitant

notre site sur www.inglis.ca.

Dans votre correspondance, veuillez indiquer un numero de

telephone ou I'on peut vous joindre dans la journee.

Conservez ce manuel et votre regu de vente ensemble pour

r_f_rence ult_rieure. Pour le service sous garantie, vous

devez presenter un document prouvant la date d'achat ou

d'installation.

Inscrivez les renseignements suivants au sujet de votre appareil

menager pour vous aider a obtenir assistance ou service en cas

de besoin. Vous devrez connaftre le numero de modele et le

numero de serie au complet. Vous trouverez ces renseignements

sur la plaque signaletique situee sur la paroi interne du

compartiment de refrig6ration.

Nora du marchand

Numdro de s_rie

Adresse

Numdro de tdl_phone

Numdro de module

Date d'achat

SECURITEDUREFRIGERATEUR

Votre s_curit_ et celle des autres est tres importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tousles messages de securite et de vous y conformer.

Voici le symbole d'alerte de securite.

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous

eta d'autres.

Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou

"AVERTISSEMENT'. Ces roots signifient :

Risque possible de deces ou de blessure grave si vous ne

suivez pas immediatement lee instructions.

Risque possible de deces ou de blessure grave si vous

ne euivez pas lee instructions.

Tous les messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES iNSTRUCTiONS DE SI_=CURITI_=

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou des blessures Iors de I'utilisation du

refrigerateur, prendre quelques precautions fondamentales, y compris les suivantes :

[] Brancher I'appareil sur une prise A 3 alveoles reliee A la [] Enlever les portes de votre vieux refrigerateur.

terre.

[] Ne pas enlever la broche de liaison A la terre.

[] Ne pas utiliser un adaptateur.

[] Ne pas utiliser un cable de rallonge.

[] Debrancher la source de courant electrique avant

I'entretien.

[] Replacer pieces et panneaux avant de faire la remise en

marche.

[] Utiliser un produit de nettoyage ininflammable.

[] Garder les mat@iaux et les vapeurs inflammables, telle que

I'essence, loin du refrigerateur.

[] Utiliser deux ou plus de personnes pour deplacer et

installer le refrigerateur.

[] Debrancher le refrigerateur avant I'installation de la

machine A glagons (seulement pour modeles pr_ts A

recevoir une machine A glagons).

CONSERVEZ CES INSTRUCTIONS

Mise au rebut de votre vieux r6frig6rateur Avant de jeter votre vieux r6frig6rateur ou cong61ateur :

Enlever les portes.

Laisser les tablettes en place de sorte que les enfants ne

puissent pas y pen6trer facilement.

Risque de suffoquer

Enlever les portes de votre vieu× r6frig6rateur.

Le non=respect de cette instruction peut causer

un d6ces ou des 16sions c6r6brales.

IMPORTANT : L'emprisonnement et I'etouffement des enfants ne

sont pas un probleme du passe. Les refrigerateurs jetes ou

abandonnes sent encore dangereux, m_me s'ils sent laisses

abandonnes pendant "quelques jours seulement". Si vous vous

debarrassez de votre vieux refrigerateur, veuillez suivre les

instructions suivantes pour aider A eviter les accidents.

INSTRUCTIONSD'INSTALLATION

Risque du poids e×cessif

Utiliser deu× ou plus de personnes pour d6placer et

installer le r6frig6rateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Retirer les materiaux d'emballage

Ne pas utiliser d'instruments coupants, d'alcool A friction, de

liquides inflammables ou de nettoyants abrasifs pour enlever le

ruban adhesif ou la colle. Ces produits peuvent endommager la

surface de votre refrig@ateur. Pour plus de renseignements, voir

la section "Securite du refrigerateur".

IMPORTANT : Ne pas enlever le dispositif de refoulement de I'air

en mousse blanche de derriere le panneau de commande sur le

plafond du refrigerateur. Si le dispositif est enleve, de la glace peut

se former en provenance du congelateur et causer laformation de

glagons.

Deplacement de votre r6frigerateur :

Votre refrig6rateur est Iourd. Lots du deplacement du

refrig6rateur pour le nettoyage ou le service, veiller A proteger

le plancher. Toujours tirer le refrig@ateur tout droit Iors du

deplacement. Ne pas incliner le refrig@ateur d'un c6te ou de

I'autre nile "faire marcher" en essayant de le deplacer car le

plancher pourrait _tre endommage.

Nettoyage avant I'utilisation

Apres avoir enleve tous les mat@iaux d'emballage, nettoyer

I'int@ieur du refrig6rateur avant de I'utiliser. Voir les instructions de

nettoyage dans la section "Entretien du refrigerateur".

Importants renseignements a savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

I'eau tiede quand ils sent froids. Les tablettes et les

couvercles peuvent se briser s'ils sont exposes a des

changements soudains de temperature ou a un impact tel

que coup brusque. Pour votre protection, le verre trempe est

con£u pour eclater en d'innombrables pieces minuscules.

Ceci est normal. Les tablettes et les couvercles en verre sont

Iourds. Un soin special s'impose Iors de leur deplacement

pour eviter I'impact d'une chute.

REMARQUE : IIest recommande de ne pas installer le

refrigerateur pres d'un four, d'un radiateur ou de toute autre

source de chaleur. Ne pas installer le refrigerateur dans un endroit

ou la temp@ature baissera au-dessous de 55°F (13°C).

3" (7,5 cm} --/

II I

JlI

2" 15,08cm)

Risque d'explosion

Garder les materiaux et les vapeurs inflammables, telle

que ressence, loin du refrig_rateur.

Le non-respect de cette instruction peut causer

un deces, une explosion ou un incendie.

Pour obtenir une a@ation appropriee pour votre refrigerateur,

laisser un espace de 1/2"(12,70 mm) de chaque c6te. Laisser un

espace de 3" (7,5 cm) entre le dessus du refrigerateur et le

dessous des armoires. Laisser au moins 1" (25,40 mm) entre

I'arriere du refrigerateur et lemur. Si votre refrigerateur comporte

une machine a glagons, s'assurer qu'un espace additionnel est

prevu a I'arriere pour permettre les connexions des conduits

d'eau.

• Si vous installez votre refrigerateur pres d'un mur fixe, laisser

un minimum de 2" (5,08 cm) du c6te des charnieres (selon le

modele) pour permettre a la porte de s'ouvrir sans

obstruction.

• 12tablir I'aplomb du refrig@ateur. Voir "Ajustement des portes".

Risque de choc electrique

Brancher sur une prise a 3 alveoles reli_,e a la terre.

Ne pas enlever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un cable de rallonge.

Le non-respect de ces instructions peut causer

un d_ces, un incendie ou un choc _lectrique.

Avant de placer le refrigerateur a son emplacement final, il est

important de vous assurer d'avoir la connexion electrique

appropriee.

M_thode recommand_e de mise _ la terre

Une source d'alimentation de 115 volts, 60 Hz, type 15 ou

20 amperes CA seulement, protegee par fusible et adequatement

mise a la terre, est necessaire. II est recommande d'utiliser un

circuit distinct pour alimenter uniquement votre refrigerateur.

Utiliser une prise murale qui ne peut pas _tre mise hors circuit a

I'aide d'un commutateur. Ne pas utiliser un cable de rallonge.

REMARQUE : Avant d'executer tout type d'installation, nettoyage

ou remplacement d'une ampoule d'eclairage, tourner la

commands (reglage du thermostat, du refrigerateur ou du

congelateur selon le modele) a OFF (arr_t) et deconnecter ensuite

le refrigerateur de la source d'alimentation electrique. Lorsque

vous avez termine, reconnecter le refrigerateur a la source

d'alimentation electrique et tourner de nouveau la commande

(reglage du thermostat, du refrigerateur ou du congelateur selon

le modele) au reglage desire.

Lire attentivement toutes les instructions avant de commencer.

IMPORTANT:

• Si on dolt utiliser le refrigerateur avant qu'il soit raccorde & la

canalisation d'eau, placer la commande de la machine

glagons a la position OFF (arr_t).

• Toutes les installations doivent _tre conformes aux exigences

des codes Iocaux de plomberie.

• Utiliser un tube en cuivre et verifier s'il y a des fuites. Installer

les tubes en cuivre seulement a des endroits ou la

temperature se maintient au-dessus du point de congelation.

OUTILLAGE NI_OESSAIRE : Tournevis a lame plate, cles plates

de 7/_6"et W' ou deux cles a molette reglables, tourne-ecrou et

foret de V4",perceuse manuelle ou electrique (convenablement

reliee a la terre). Rassembler les outils et pieces necessaires avant

de commencer I'installation. Lire et suivre les instructions fournies

avec les outils indiques ici.

REMARQUE :Votre marchand de refrigerateurs presente une

trousse disponible avec un robinet d'arr_t &etrier de V4"

(6,35 mm), un raccord et un tube en cuivre. Avant I'achat,

s'assurer que le robinet d'arr_t a etrier est conforme a vos codes

Iocaux de plomberie. Ne pas employer de robinet d'arr_t & etrier

de 3/_6"(4,76 mm) ou de type a percer, ce qui reduit le debit d'eau

et cause une obstruction plus facilement.

Pression de I'eau

Une alimentation en eau froide avec une pression entre 30 et

120 Ib/po _(207 - 827 kPa) est necessaire pour faire fonctionner la

machine a glagons. Si vous avez des questions au sujet de la

pression de votre eau, faire appel a un plombier qualifie agree.

Alimentation en eau par osmose inverse

Si un systeme de purification de I'eau par osmose inverse est

raccorde a votre alimentation en eau froide, la pression de I'eau

au syst_me dolt _tre d'un minimum de 40 a 60 Ib/po _(276 -

414 kPa).

Si la machine & glagons ne distribue toujours pas d'eau au debit

approprie :

• Verifier pour voir si le filtre du systeme d'osmose inverse est

bloque, et le remplacer si necessaire.

• Laisser le reservoir du systeme d'osmose inverse se remplir

apres une utilisation intense.

Si vous avez des questions au sujet de la pression de votre eau,

appeler un plombier qualifie agree.

Liretoutes les instructions avant de commencer.

IMPORTANT: Si on met en marche le refrigerateur avant son

raccordement & la canalisation d'eau, placer la commande de la

machine &glagons a la position OFF (arr_t).

Raccordement _ une canalisation d'eau

1. Debrancher le refrigerateur ou deconnecter la source de

courant electrique.

2. FERMER le robinet principal d'arrivee d'eau. OUVRIR le

robinet de puisage le plus proche pendant une p_riode

suffisante pour que la canalisation d'eau se vide.

3= Trouver une canalisation d'eau froide verticale de W' a 1V4"

(1,27 a 3,18 cm) pros du rdrigerateur.

IMPORTANT :

S'assurer qu'il s'agit d'une canalisation d'eau froide.

Un conduit horizontal fonctionnera mais percer par le

dessus de la canalisation et non pas par le dessous. Ainsi,

I'eau ne risquera pas d'arroser la perceuse et ceci

emp_chera egalement les s_diments qu'on trouve

normalement dans I'eau de s'accumuler dans le robinet

d'arr_t.

4. Pour determiner la Iongueur du tube en cuivre, il faut mesurer

la distance entre le point de connexion inferieur gauche

I'arriere du refrigerateur et le tuyau d'arrivee d'eau. Ajouter

une Iongueur de 7 pi (2,1 m) pour permettre le deplacement

du refrigerateur pour le nettoyage. Utiliser un tube en cuivre

de V4"(6,35 mm) de diametre exterieur. Veiller ace que le tube

soit coupe d'equerre aux deux extremites.

5. /_,I'aide d'une perceuse electrique reliee a la term, percer un

trou de V4"dans le tuyau de canalisation d'eau froide choisie.

A. Canalisation d'eau

froide

B. Bride de tuyau

C. Tube en cuivre

D. Ecrou de compression

E.Bague de compression

Robinet d'arr_t

G. Ecrou de serrage

6. Fixer le robinet d'arr_t sur la canalisation d'eau froide avec la

bride de tuyau. Verifier que le raccord du robinet est bien

engage dans le trou de _/,"(6,35 mm) perce dans la

canalisation et que la rondelle d'etancheite est placee sous la

bride de tuyau. Serrer I'ecrou de serrage. Serrer lentement et

uniformement les vis de la bride de tuyau afin que la rondelle

forme une jonction etanche. Ne pas serrer excessivement car

ceci pourrait provoquer I'ecrasement du tube en cuivre.

7. Enfiler I'ecrou et la bague de compression du raccord sur le

tube en cuivre comme on le volt sur I'illustration. Inserer

I'extremite du tube aussi loin que possible dans I'ouverture de

sortie du robinet. Visser I'ecrou de compression sur le raccord

de sortie avec une cle a molette. Ne pas serrer

excessivement.

8. Placer le bout libre du tube dans un contenant ou evier et

OUVRIR le robinet principal d'arrivee d'eau et laisser I'eau

s'ecouler par le tube jusqu'a ce que I'eau soit limpide.

FERMER le robinet principal d'arrivee d'eau. Enrouler le tube

en cuivre en spirale.

Raccordement au r_frigerateur

REMARQUE : Pour les modeles en kit, installer la valve d'entree

d'eau sur le refrigerateur conformement aux instructions du kit.

Style 1

1. Debrancher le refrigerateur ou deconnecter la source de

courant electrique.

2. Connecter le tube en cuivre au robinet d'eau en utilisant un

ecrou et une bague de compression tel qu'illustre. Serrer

I'ecrou de compression. Ne pas serrer excessivement.

3. Utiliser la bride du tube a I'arriere du refrigerateur pour fixer le

tube au refrigerateur tel qu'illustre. Ceci aidera a eviter les

dommages au tube Iorsque le refrigerateur est pousse contre

lemur.

4. OUVRIR le robinet d'arr_t.

Achever I'installation

Inspecter pour rechercher les fuites. Serrer tousles raccords

(y compris les raccordements de la valve d'entree d'eau) ou

les ecrous qui coulent.

A. Bride du tube C. Ecrou de compression

B. Tube en cuivre D. Valve d'entr_e d'eau

La machine & gla(;ons est equipee d'un filtre & eau incorpor&

Si la qualite de I'eau distribuee Iocalement necessite un

deuxieme filtre a eau, il serait utile de I'installer dans le tube de

raccordement de 1/4"(6,35 mm). On peut obtenir un tel filtre &

eau chez le marchand d'appareils electromenagers le plus

proche.

Style 2

1. Debrancher le refrig@ateur ou deconnecter la source de

courant electrique.

2. Deconnecter la bride du tube & I'arriere du produit et introduire

le tube en cuivre dans la bride, tel qu'indiqu&

3. Connecter le tube en cuivre a I'entree d'eau de la valve en

utilisant un ecrou etune bague de compression tel qu'illustr&

4. Serrer I'ecrou de compression. Ne pas serrer excessivement.

Reattacher la bride du tube et le tube a I'arriere de la caisse.

= :il

._,0

A. Bride du tube C. Ecrou de compression

B. Tube en cuivre

OUVRIR le robinet d'arr_t. Inspecter pour rechercher les

fuites. Serrer tousles raccords (y compris les raccordements

de la valve d'entree d'eau) ou les ecrous qui coulent.

La machine a gla(_ons est equipee d'un filtre a eau incorpor&

Si la qualite de I'eau distribuee Iocalement necessite un

deuxieme filtre a eau, il serait utile de I'installer dans le tube de

raccordement de 1/4"(6,35 mm). On peut obtenir un tel filtre

eau chez le marchand d'appareils electromenagers le plus

proche.

Risque de choc electrique

Brancher sur une prise a 3 alveoles reli_,e a la terre.

Ne pas enlever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un c_ble de rallonge.

Le non=respect de ces instructions peut causer

un d_ces, un incendie ou un choc _lectrique.

Brancher sur une prise & 3 alveoles reliee & la terre.

REMARQUE :Attendre 24 heures pour produire la premiere

quantite de glagons. Jeter les trois premieres quantites de

glagons produites. Attendre 3 jours pour que le bac & gla(;ons se

remplisse entierement.

OUTILLAGE NI_CESSAIRE : Cle a douille avec douille

hexagonale de %6", tournevis Phillips n° 2, tournevis a lame plate,

cle plate de %d', couteau a mastic plat de 2".

IMPORTANT :

• Avant de commencer, tourner la commande du refrigerateur

OFF (arr_t). Debrancher le refrigerateur ou deconnecter la

source de courant electrique.

• Retirer les aliments et tout balconnet ou casier utilitaire de la

porte du refrig@ateur.

• Si vous desirez seulement enlever et reinstaller les portes, voir

"Demontage - Portes et charnieres" et "Reinstallation - Portes

et charnieres".

Selon votre modele, vous pouvez avoir des portes standard

(Style 1) ou contoured (Style 2). Si on prevoit egalement

d'inverser le sens d'ouverture des portes, suivre les

instructions pour le style de porte appropri&

D_montage - Portes et charni_res

Vis de charniere a t_te hexagonale de _6"

1. Debrancher le refrigerateur ou deconnecter la source de

courant electrique.

2. Fermer la porte du refrigerateur; maintenir les deux portes

fermees jusqu'au moment 0(4on est pr_t &les separer de la

caisse de I'appareil.

REMARQUE : Prevoir un support additionnel des portes

pendant le demontage des charnieres. La force d'attraction

des aimants des portes ne suffit pas ales maintenir en place.

3. Enlever les pieces de la charniere superieure - voir I'illustration

de la charniere superieure. Soulever la porte du compartiment

de congelation pour la separer de la caisse.

4. Enlever les pieces de la charniere centrale - voir I'illustration

de la charniere centrale. Soulever la porte du refrig6rateur

pour la separer de la caisse.

5. Enlever les pieces de la charniere inferieure - voir I'illustration

de la charniere inferieure.

Inversion des portes (facultatif)

IMPORTANT : Si on souhaite inverser la position des portes pour

pouvoir les ouvrir dans la direction opposee, proceder comme

suit. S'il n'est pas necessaire de changer I'orientation des portes,

voir "R_installation - Portes et charnieres" plus loin dans cette

section.

Style 1 - Standard

Les illustrations suivent ces instructions.

Vis de butte de la porte

Vis de scellement

de lapoignee de laporte

Vis de la poignee _ t_te plate

Vis frontale de scellement

de lapoignee de laporte

Caisse

Bouchon d'obturation

de charni#re de porte

Bouchon d'obturation

de charni#re de caisse

Couvre-vls

de la poign#e de la porte

Vis de poignee

t#te ronde

Enlever les vis a t_te hexagonale de sA6"de la charniere (c6te

poignee); transferer ces pieces du c6te oppos& Voir

I'illustration 1-1.

Enlever les bouchons obturateurs des trous au sommet de la

caisse; transferer ceux-ci dans les trous de charniere du c6te

oppos& Voir I'illustration 1-2.

Porte du compartiment de cong_lation

1. Enlever la poignee de la porte du compartiment de

congelation. Voir I'illustration. Conserver toutes les pieces

ensemble, Voir I'illustration 2.

2. Enlever le bouchon obturateur de charniere de porte.

Transferer le bouchon du c6te oppos& Voir I'illustration 3,

3. Enlever les vis de scellement de la poignee de la porte.

Transferer ces vis du c6te oppose de la porte du

compartiment de congelation. Voir I'illustration 4.

4. Enlever la butee de porte. Transferer la butee du c6te oppose

de la porte du compartiment de congelation, Voir

I'illustration 5.

5. Positionner la poignee du compartiment de congelation du

c6te oppose de la porte. Fixer la poignee sur la porte, Voir

I'illustration 2.

6. Serrer toutes les vis, Conserver la porte & part jusqu'a la mise

en place des charnieres de la porte du compartiment de

refrigeration.

Porte du compartiment de r_frig_ration

1. Enlever le couvre-vis. Voir I'illustration 6,

2. Enlever la poignee de la porte du compartiment de

refrigeration. Voir I'illustration, Conserver toutes les pieces

ensemble. Voir I'illustration 6.

3. Enlever le bouchon obturateur de charniere sur la porte du

refrigerateur. Transferer le bouchon obturateur au trou du c6te

oppos& Voir I'illustration 3.

4. Enlever les vis de scellement de la poignee de la porte,

Transferer ces vis du c6te oppose de la porte du refrigerateur.

Voir I'illustration 4.

5. Enlever la vis frontale de scellement de la poignee de porte.

Transferer du c6te oppose de la porte du refrigerateur. Voir

I'illustration 7.

6. Enlever la butee de porte. Transferer la piece du c6te oppose

de la porte du refrigerateur. Voir I'illustration 5.

7. Positionner la poignee de porte du refrigerateur sur le c6te

oppose de la porte. Voir I'illustration 6, Placer d'abord les

deux vis sup_rieures de la poignee. Aligner la partie inferieure

de la poignee, puis visser la vis inferieure.

8. Reinstaller le couvre-vis. Voir I'illustration 6.

9. Serrer toutes les vis. Conserver la porte du refrigerateur & part

jusqu'a ce que la charniere inferieure soit installee sur le

refrigerateur.

Style2 - Contoured

Lesillustrations suivent ces instructions.

Vis depoignee Bouchon obturateur

t#te ronde de la vis de poignee

de porte

Bouchon obturateur

de charni#re de

porte

Caisse

1. Enlever les vis de charniere a t_te hexagonale de %6" (c6te

poignee) et les transferer au c6te oppose. Voir

I'illustration 1-1.

2. Enlever les bouchons obturateurs des charnieres au sommet

de la caisse et les placer darts les trous de charniere du c6te

oppose. Voir I'illustration 1-2.

Portes

1. Enlever le bouchon obturateur de charniere de porte au

sommet de la porte du congelateur. Le deplacer au c6te

oppose tel qu'illustre. Voir I'illustration 2.

2. Enlever la butee de la porte du compartiment de congelation

et celle de la porte du compartiment de refrigeration et les

transferer au c6te oppose. Voir I'illustration 3.

R_installation - Portes et charnieres

REMARQUE :Si on inverse le sens d'ouverture des portes,

considerer I'image symetrique.

1. Reinstaller les pieces de la charniere inferieure. Voir

I'illustration. Serrer les vis. Reinstaller la porte du

compartiment de refrigeration.

REMARQUE : Prevoir un support additionnel des portes

pendant la reinstallation des charnieres. La force d'attraction

des aimants des portes ne suffit pas ales maintenir en place.

2. Assembler les pieces de la charniere centrale. Voir

I'illustration. Serrer toutes les vis. Voir I'illustration de la

charniere centrale. Reinstaller la porte du compartiment de

congelation.

3. Assembler les pieces de la charniere superieure. Voir

I'illustration - charniere superieure. Ne pas completement

serrer les vis.

4. Aligner correctement les portes au niveau de la separation

entre le bas de la porte du compartiment de cong_lation et le

sommet de la porte du refrigerateur. Serrer toutes les vis.

Etapes finales

1. Inspecter tous les trous. Verifier que tousles bouchons

obturateurs et vis sont en place. Reinstaller le couvercle de la

charniere superieure. Voir I'illustration - charniere superieure.

Risque de choc electrique

Brancher sur une prise a 3 alveolea reli_,e a la terre.

Ne pas enlever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un cable de rallonge.

Le non-respect de ces instructions peut causer

un d_ces, un incendie ou un choc _lectrique.

2. Brancher le refrigerateur ou reconnecter la source de courant

electrique.

3. Effectuer les reglages necessaires. Voir "Utilisation des

commandes".

4. Reinstaller les balconnets et autres pieces amovibles; repartir

les aliments sur les balconnets.

La page charge ...

Inglis IST143301 Le manuel du propriétaire

Marque: Inglis

Modèle: IST143301

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Inglis IST143301 Owner's manual

Inglis IST143301 Le manuel du propriétaire

Inglis IST143301 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents