KitchenAid KTRA19EMBT00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KTRA19EMBT00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

®itchen_kid ®

TOP-MOUNT REFRIGERATOR

iJ i!!!i!i_:_ii!i!!_¸,,_:!i!il;_:_:¸_i!iiilliil;iiiii_i_'_i:_!__i',iiiii_ii_iii__;::li_i!!_¸

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

P P P

REFRIGERATEUR SUPERPOSE

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777 ou visitez notre site web &...

www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 2

2301879

TABLE OF CONTENTS

REFRIGERATOR SAFETY .................................................................... 2

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS ........................................................ 3

Unpack the Refrigerator ..................................................................... 3

Location Requirements ...................................................................... 4

Electrical Requirements ..................................................................... 4

Water Supply Requirements .............................................................. 4

Connect the Water Supply ................................................................. 5

Refrigerator Doors ............................................................................. 6

Adjust the Doors .............................................................................. 11

Prepare the Water System ............................................................... 11

Normal Sounds ................................................................................ 11

REFRIGERATOR USE ........................................................................ 12

Ensuring Proper Air Circulation ........................................................ 12

Using the Controls ........................................................................... 12

Water Dispenser ............................................................................... 13

Water Filter Status Light .................................................................. t 3

Water Filtration System .................................................................... 13

Ice Maker .......................................................................................... 14

REFRIGERATOR FEATURES ............................................................ 14

Refrigerator Shelves ......................................................................... 14

Crispers and Meat Drawers ............................................................. 15

Crisper Humidity Control ................................................................. 15

Chilled Meat Drawer ......................................................................... 16

Wine or Can/Bottle Rack ................................................................. 16

Utility or Egg Bin ............................................................................... 16

FREEZER FEATURES ........................................................................ 16

Freezer Shelf .................................................................................... 16

Pull-out Freezer Floor ....................................................................... t 6

DOOR FEATURES .............................................................................. 17

Door Rails ......................................................................................... 17

Can Racks and Door Bins ................................................................ 17

Adjustable Utility Compartment & Tray ........................................... 17

Flip-up Door Shelf ............................................................................ 17

REFRIGERATOR CARE ..................................................................... 18

Cleaning ........................................................................................... 18

Changing the Light Bulbs ................................................................ 18

Power Interruptions .......................................................................... 18

Vacation and Moving Care ............................................................... 19

TROUBLESHOOTING ........................................................................ 19

ASSISTANCE OR SERVICE ............................................................... 21

In the U.S.A ...................................................................................... 21

In Canada ......................................................................................... 22

Accessories ...................................................................................... 22

WATER FILTER CERTIFICATIONS ................................................... 22

PRODUCT DATA SHEETS ................................................................. 23

WARRANTY ........................................................................................ 24

TABLE DES MATIERES

SECURITE DU REFRIGleRATEUR .................................................... 25

Mise au rebut de votre vieux refrig6rateur ................................. 25

INSTRUCTIONS D'INSTALLATION .................................................. 26

D6ballage du r6frig6rateur ............................................................... 26

Emplacement d'installation ............................................................. 26

Sp&cifications 61ectriques ............................................................... 27

Sp6cifications de I'alimentation en eau ........................................... 27

Raccordement de la canalisation d'eau .......................................... 27

Portes du r&frig6rateur .................................................................... 29

Ajustement des portes .................................................................... 34

Pr6paration du syst_me d'eau ........................................................ 34

Sons normaux .................................................................................. 34

UTILISATION DU REFRIGleRATEUR ............................................... 35

Pour s'assurer d'une circulation d'air appropri6e ........................... 35

Utilisation des commandes ............................................................. 35

Distributeur d'eau ............................................................................ 36

Le t6moin lumineux de I'&tat du filtre & eau .................................... 36

Syst_me de filtration d'eau .............................................................. 36

Machine & glagons ........................................................................... 37

CARACTERISTIQUES DU REFRIGERATEUR ................................. 38

Tablettes du r6frig6rateur ................................................................ 38

Bacs & I&gumes et tiroirs &viande .................................................. 38

R&glage de I'humidit6 dans le bac & 16gumes ................................ 39

Tiroir _ viande refrig6r6 .................................................................... 39

Casier & vin ou porte-cannettes/bouteilles ..................................... 39

Casier utilitaire ou oeufrier ............................................................... 39

CARACTERISTIQUES DU CONGELATEUR .................................... 40

Clayette de cong61ateur .................................................................. 40

Plancher de cong61ateur coulissant ................................................ 40

CARACTERISTIQUES DE LA PORTE .............................................. 40

Tringles dans la porte ...................................................................... 41

Porte-cannettes et balconnets ........................................................ 41

Compartiment utilitaire et plateau r6glables ................................... 41

Tablette de porte relevable .............................................................. 41

ENTRETIEN DU RleFRIGleRATEUR .................................................. 42

Nettoyage ........................................................................................ 42

Remplacement des ampoules d'6clairage ...................................... 42

Pannes de courant .......................................................................... 43

Entretien avant les vacances ou Iors d'un dem&nagement ............ 43

DI_PANNAGE ...................................................................................... 44

ASSISTANCE OU SERVICE .............................................................. 46

Accessoires ..................................................................................... 46

FEUlLLES DE DONNC:ES SUR LE PRODUlT .................................. 47

GARANTIE .......................................................................................... 48

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

_,Use nonflammable cleaner.

_,Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

_,Use two or more people to move and install refrigerator.

_,Disconnect power before installing ice maker (on ice maker

kit ready models only).

_,Use a sturdy glass when dispensing ice or water (on some

models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Depending on your model, to remove the protective

(transparent) film that is on the nameplate, which is located

on the freezer handle, use your fingernail and peel off the film,

starting from one side and peeling to the other.

• There are four bolts that secure the refrigerator to the

shipping case. Keep these bolts because they are the

refrigerator's leveling legs.

IMPORTANT: Do not remove the white foam air return insert that

is located behind the control panel on the ceiling of the

refrigerator (on some models). The insert is part of the refrigerator

. and not part of the packing material. If the insert is removed, ice

may migrate down from the freezer and cause icicles to form.

Remove the Packaging Materials

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pu!I the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

On some models, shelves, bins, door shelf rails, and other

feature parts may be packaged in the Interior FeaturePak.

Follow the instructions contained in the package for proper

assembly.

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Expmoeion Hazard

Keep flammable materials and vapors, such as

gaeomine, away from refrigerator.

Faimureto do so can reeumt in death, expmosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on

each side (depending on your model) to allow for the door to

swing open. Ifyour refrigerator has an ice maker, allow extra

space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

1/2'(1.25 ore}

II I

iu --_E

2" {5°08cm}

Electricam Shock Hazard

Pmuginto a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can resumt in death,

fire, or eiectricam shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Read all directions carefully before you begin.

IMPORTANT:

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7_6"and 1/2"open-end

wrenches or two adjustable wrenches, 1/4"nut driver and drill bit,

hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a %"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 - 827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

See "Water Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

Locate a 1/2"to 11/4'' (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a grounded drill, drill a %" hole in the cold water pipe

you have selected.

G ........•....................B

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help prevent

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A. Tube clamp

B. Copper tubing

C. Compression nut

D. Valve inlet

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4"(6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See "Prepare the Water System."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. A 1/4"x 1/4"coupling is needed in order to connect the water

tubing to an existing household water line. Thread the

provided nut onto the coupling on the end of the copper

tubing.

NOTE:Tightenthenutbyhand.Thentightenitwithawrench

twomoreturns.Donotovertighten.

A B c o

A.Refrigerator water tubing D.Coupling (provided)

B.Nut (provided) E.Ferrule(purchased)

C.Bulb E Nut (purchased)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system. See "Prepare the Water System."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A. Bulb

B.Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system. See "Prepare the Water System."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Standard Contour Architectc_Series

Remove Handle (Architect _ Series}

Graphics are included later in this section.

NOTE: These instructions are for the Architect _ Series doors with

curved handle only.

1. Using a 1/,,,Allen wrench, loosen the two set screws located

underneath each handle.

2. Pull handle straight out from the door. Make sure you keep

screws for reattaching handles.

Remove Doors and Hinges (all models)

IMPORTANT:

• Before you begin, turn the refrigerator control OFE Unplug

refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

If you are only removing and replacing the doors, the

instructions are the same regardless of door style.

If you have a standard or contour door and are also going to

reverse the door swing, follow the instructions for the

appropriate door style.

All graphics referenced in the following instructions are

included later in this section after "Final Steps."

5/16"Hex-Head Hinge Screw

TOOLS NEEDED: %6" hex-head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, %6" open-end wrench, flat 2"

putty knife.

1. Unplug refrigerator or disconnect power.

2. Open refrigerator door and remove base grille from the

bottom front of the refrigerator. See Base Grille graphic.

3. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

4. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

5. Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

6. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

Reverse Doors (optional on some models}

IMPORTANT:

• Architect ®Series doors with curved handle are not reversible.

• If you want to reverse your standard or contour doors so they

open from the opposite side, follow these steps. Ifyou are not

reversing the doors, see "Replace Doors and Hinges."

Standard Door

Graphics are included later in this section.

Door Stop Screw

Door Handle Sealing Screw

Flat-Head Handle Screw

Door Handle Seal Screw Front

Door Hinge Hole Plug

Cabinet Hinge Hole Plug

Round-Head Handle Screw

Shoulder Handle Screw

Cabinet

1. Remove %6" hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and move

them to opposite side hinge holes as shown. See

Graphic 1-2.

Freezer door

1. Remove freezer handle assembly as shown. Keep all parts

together. See Graphic 2,

2. Remove door hinge hole plug. Move to opposite side as

shown. See Graphic 3.

3. Remove door handle sealing screws, Move to opposite side

of freezer door as shown. See Graphic 4.

4. Remove door stop. Move to opposite side of freezer door as

shown. See Graphic 5.

5. Position handle on opposite side of freezer door. Assemble

handles on door as shown, See Graphic 2,

6. Tighten all screws, Set aside door until hinges and

refrigerator compartment door are in place.

Refrigerator door

1. Remove refrigerator handle assembly as shown. Keep all

parts together. See Graphic 6-1.

2. Remove shoulder handle screw from refrigerator door as

shown. Keep all parts together. See Graphic 6-2.

3. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown. See Graphic 3.

4. Remove door handle sealing screws, Move to opposite side

of refrigerator door as shown, See Graphic 4.

5. Remove door handle seal screw front, Move to opposite side

of refrigerator door as shown, See Graphic 7,

6. Position shoulder handle screw on opposite side of

refrigerator door and drive screw as shown. See Graphic 6-2.

7. Remove door stop. Move to opposite side of refrigerator door

as shown, See Graphic 5,

8. Position refrigerator handle on opposite side of the

refrigerator door as shown in Graphic 6-3. Drive the top two

screws in handle first, Align the lower portion of handle and

drive bottom screw.

9. Tighten all screws. Set aside the refrigerator door until the

bottom hinge is installed on the product.

Contour Door

Graphics are included laterin this section.

Round-Head Door Handle

Handle Screw Screw HolePlug

Door Hinge

Hole Plug

Cabinet

1. Remove %6" hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from the cabinet top and

move them to opposite side hinge holes as shown in

Graphic 1-2.

Doors

1. Remove door hinge hole plug from top of freezer door. Move

to opposite side as shown in Graphic 2.

2. Remove door stop from both the freezer and refrigerator

door. See Graphic 3.

NOTE: When reversing the door, the freezer handle becomes the

refrigerator door handle and the refrigerator door handle

becomes the freezer handle. See Door Handle Reversal graphic.

3. Remove freezer handle assembly as shown, Keep all parts

together. See Graphic 4.

4. Remove refrigerator handle assembly as shown. Keep all

parts together. See Graphic 5.

5. Rotate and position handle from refrigerator door onto freezer

door and assemble as shown in Graphic 6.

6. Rotate and position handle from freezer door onto refrigerator

door and assemble as shown in Graphic 7.

7. Reinstall door stops to opposite side. See Graphic 8.

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown and tighten

screws, See Bottom Hinge graphic. Replace the refrigerator

door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten

all screws. See Center Hinge graphic, Replace the freezer

door.

3. Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten screws completely,

4. Line up the doors so that the bottom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten all

screws.

Final Steps

Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover. See Top Hinge graphic,

NOTE: On the left-hand side of the base grille there is a

removable tab which is a bottom hinge hole plug, Break off

the tab from the base grille and insert the bottom hinge hole

plug into the bottom hinge holes, See Base Grille graphic,

2. Replace the base grille. See Base Grille graphic.

3. Plug in refrigerator or reconnect power.

4. Reset the controls. See "Using the Controls."

5. Return all removable door parts to the doors and food to the

product.

Standard

iiiiiiiiiiiiiiiiiiiiiiii

B .....................

A. Door Hinge Hole Plug

A. Flat-Head Handle Screws

B. Freezer Door Handle

A. Door Handle Sealing Screws

Front View Side View

-r7

A. Door Stop Screw A B

B. Door Stop

I I

A. Cabinet Hinge Hole Plugs

s _

A._8" Hex-Head Hinge Screws

A Door Handle

Seal Screw Front

A. Flat-Head

Handle Screw

B. Round-Head

Handle Screw

Contour

iiiiiiiiiiiiii,,,ii

A .........................................................................

A. Bottom Hinge Hole Plug

Top Hinge

A. Top Hinge Cover

B. _" Hex-Head Hinge Screws

C. Top Hinge

Center Hinge

A. Center Hinge

B. _" Hex-Head Hinge Screws

Bottom Binge

A. Bottom Hinge

B. _" Hex-Head Hinge Screws

iiiiiiiiiiiiiiiiiiiiiiiiiii

Door Handle Reversal

[]

Reinstallation of Door Stops

A. Door Stop

B. Door Stop Screw

A. Cabinet Hinge Hole Plugs

A _

_?" -G\, I

A. Door Hinge Hole Plug

Removal of Door Stops

A. Door Stop

B. Door Stop Screw

Freezer Door

............................A

A. Door Handle Sealing Screws

B. Door Handle Screw Hole Plugs

Refrigerator Door

T.....................B T

A. Door Handle Screw Hole Plugs

B. Door Handle Sealing Screws

Freezer Door

A....................A

A. Door Handle Sealing Screws

B. Door Handle Screw Hole Plugs

Refrigerator Door

A. Door Handle Screw Hole Plugs

B. Door Handle Sealing Screws

Base Grille

A. Bottom Hinge Hole Plug

A. Top Hinge Cover

B. 5/_e"Hex-Head Hinge Screws

C. Top Hinge

Center Hinge

A. Center Hinge

B. 5/_6"Hex-Head Hinge Screws

Bottom Hinge

A. Bottom Hinge

B. _6" Hex-Head Hinge Screws

A. 1/8" Set Screw

Door Closing

Your refrigerator has two front adjustable rollers - one on the right

and one on the left. Ifyour refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the instructions below:

1. Plug into a grounded 3 prong outlet.

2. Move the refrigerator into its final location.

3. Remove the base grille. See Base Grille graphic. The two

leveling screws are part of the front roller assemblies which

are at the base of the refrigerator on either side.

4. Use a screwdriver to adjust the leveling screws. Turn the

leveling screw to the right to raise that side of the refrigerator

or turn the leveling screw to the left to lower that side. It may

take several turns of the leveling screws to adjust the tilt of

the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

5. Open both doors again and check to make sure that they

close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It

may take several more turns, and you should turn both

leveling screws the same amount.

6. Replace the base grille.

Align Doors

If the space between your doors looks uneven, you can adjust it

using the instructions below:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a 5/16"socket or wrench.

3. Have someone hold the door in place or put a spacer

between the doors while you tighten the top hinge screws.

4. Replace the top hinge cover.

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Turn off the ice maker by opening the freezer door and lifting

up the wire shutoff arm as shown.

NOTES:

• If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cap is in the

horizontal position.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 5 minutes and

will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Turn on the ice maker by opening the freezer door and

lowering the wire shutoff arm as shown. Please refer to the

"Ice Maker" section for further instructions on the operation

of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your refrigerator is equipped with an ice maker, you will hear

a buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

Contraction and expansion of the inside walls may cause a

popping noise.

You may hear air being forced over the condenser by the

condenser fan.

You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit

airflow between the refrigerator and freezer sections. As shown in

the illustration, cool air enters through the bottom of the freezer

section and moves up. Most of the air then flows through the

freezer section vents and recirculates under the freezer floor. The

rest of the air enters the refrigerator section through the top vent.

Do not block any of these vents with food packages. Ifthe vents

are blocked, airflow will be prevented and temperature and

moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out of food, wrap or cover foods tightly.

For your convenience, your refrigerator controls are preset at the

factory. When you first install your refrigerator, make sure that the

controls are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to

the word OFF or until the word OFF appears. Your product will

not cool when the refrigerator control is set to OFR

Mid-setting "3"

OFF

COLDES @

5 1

NORM_

Mid-setting "3"

Mid-setting "4"

IMPORTANT:

• Give your refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put food

into the refrigerator.

If you add food before the refrigerator has cooled completely,

your food may spoil. Adjusting the Refrigerator and Freezer

Controls to a higher (colder) than recommended setting will

not cool the compartments any faster.

Adjusting Controls

The mid-settings indicated inthe previous section should be

correct for normal household usage. The controls are set

correctly when milk or juice is as cold as you like and when ice

cream is firm.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the

chart below as a guide. On models with two controls, adjust the

refrigerator temperature first. Wait at least 24 hours between

adjustments and then recheck the temperatures.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section too warm Adjust REFRIGERATOR

- Door opened often, large amount or TEMPERATURE

of food added or room Control one setting

temperature very warm higher

FREEZER section too warm/ice

not made fast enough

- Door opened often, or large

amount of food added or very cold

room temperature (can't cycle

often enough)

- Heavy ice usage

Adjust FREEZER or

TEMPERATURE Control

one setting higher

REFRIGERATOR section too cold

- Controls not set correctly for

your conditions

Adjust REFRIGERATOR

or TEMPERATURE

Control one setting

lower

FREEZER section too cold Adjust FREEZER or

- Controls not set correctly for TEMPERATURE Control

your conditions one setting lower

!o;! _i¸_ii_O__ii! _i!¸iii_;i_b_;!i_ii:_ii!:!!_ii

Cut Hazard

Use a sturdy glass when dispensing ice or water°

Faimureto do so can resumt in cuts,

you did not flush the water system when the refrigerator was

first installed, dispense water into a container until you draw and

discard 2 to 3 gal. (8 to 12 L) or for approximately 5 minutes after

the water begins dispensing. The water you draw and discard

rinses the pipes. Allow several hours for the refrigerator to cool

down and chill water.

Dispensing Water

There are two water dispenser buttons, as shown, for use with

different sizes of containers.

1. Press a glass against the back button or hold a container

under the dispenser while pressing the front button.

2. Remove the glass or release the front button to stop

dispensing.

NOTE: Dispense enough water every week to maintain a fresh

supply.

Non-Indicator Water Filter (on some models)

If your refrigerator does not have the water filter status light, you

should change the water filter every 6 to 9 months depending

upon your usage. Ifthe water flow to the water dispenser or ice

maker decreases noticeably before 6 months have passed,

replace the water filter more often.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

Changing the Water Filter

Locate the filter cap in the front base grille. Rotate the cap

counterclockwise to a vertical position and pull the cap and

filter out through the base grille.

NOTE: There will be water in the filter. Some spilling may

occur.

Remove the cap by sliding it off the end of the used filter. The

cap will slide to the left or right.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. Take the new filter out of its packaging and remove the

protective cover from the O-rings.

{ t

The water filter status light, located at the top of the refrigerator

compartment, will help you know when to change your water

filter. When the water filter status light changes from green to

yellow, this tells you that it is almost time to change the water

filter (90% of the filter life has been used). It is recommended that

you replace the water filter when the water filter status light

changes to red OR water flow to your water dispenser or ice

maker decreases noticeably. To change the water filter, see

"Water Filtration System."

After changing the water filter, reset the water filter status light by

pressing the light switch 5 times within 10 seconds. The status

light will change from red to green when the system is reset.

......................................B

A. Status light

B. Light switch

Slide the cap (removed in Step 2) onto the new filter. See

illustration in Step 2.

With the cap in the vertical position, push the new filter into

the base grille until it stops. Rotate the cap clockwise to a

horizontal position. Flush the water system. See "Flushing the

Water System After Replacing Filter."

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until

the water begins to flow. Flush the water system by dispensing

and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the

system will take approximately 5 minutes and will help clear air

from the line. Additional flushing may be required in some

households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will

not be filtered.

1. Remove the base grille water filter.

2. Slide the cap off the end of the filter.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. With the cap in the vertical position, insert the cap into the

base grille until it stops.

4. Rotate the cap to a horizontal position.

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

• To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

• To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

i NORMAL

Ice Production Rate

NORMAL Ice Production: In Normal ice production mode, the

ice maker should produce approximately 8 to 12 batches of

ice in a 24-hour period. If ice is not being made fast enough,

turn the Freezer Control toward a higher (colder) number in

half number steps. (For example, if the control is at 3, move it

to between 3 and 4.) Wait 24 hours and, if necessary,

gradually turn the Freezer Control to the highest setting,

waiting 24 hours between each increase.

Optimlce Production (on some models): In Optimlce ice

production mode, the ice maker should produce

approximately 16 to 20 batches of ice in a 24-hour period. If

your refrigerator has the Optimlce ice production feature,

push the switch to Optimlce.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

_mportant information to know about glass shelves

8nd oover$:

Do not clean glass shelves or covers with warm water when

they are cold= Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping=

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces= This is normal= Glass

shelves and covers are heavy= Use special care when

removing them to avoid impact from dropping=

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This

reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models}

To Remove and Replace a Shelf in a Metal Frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the

frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To Remove and Replace a Shelf/Frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check to make sure that

the shelf is securely in position.

Drawers

To Remove and Replace a Drawer:

1. Slide drawer straight out to the stop. Lift the front of the

drawer and slide it out the rest of the way.

2. Replace a drawer by sliding it back in fully past the stop.

Crisper Cover

To Remove the Crisper(s) Cover:

1. Remove crisper(s). Hold the glass insert firmly with one hand

and press up in the center of the glass insert until it rises

above the plastic frame. Carefully slide the glass insert

forward to remove.

2. Lift the cover frame and remove it.

To Replace the Crisper(s) Cover:

NOTE: Before reinstalling the cover, make sure the U-shaped

reinforcement bar is reinstalled in the front edge of the crisper

cover.

1. Fit back of cover frame into supports on side walls of the

refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into

place.

Meat Drawer Cover

To Remove and Replace the Meat Drawer Cover:

Style 1-Glass

1. Remove the meat drawer. Tilt up the front of the cover and lift

at the back. Pull the cover straight out.

Replace the cover by guiding the rear hooks into the shelf

supports. Tilt the cover up at the front until the rear hooks

drop into the slots. Lower the front of the cover to a level

position and replace the meat drawer.

Style 2-Plastic

Remove the meat drawer. Tilt the cover up at the front and

pull it forward and out.

Replace the meat drawer cover by fitting the notches and rear

edge of the cover over rear and center crossbars on the shelf.

Lower cover into place and replace the meat drawer.

_0 ÷- _i_O_ _ _ _i

You can adjust the amount of humidity in the moisture-sealed

crisper using the settings between HIGH and LOW.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag in

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

Humidity Control Location

Humidity Control on crisper drawer

High 5 4 3 2 l LOW

CLiiiiedl ii'!¢,'iii)_:i!_ii!!iA:i[3!ii:_i!ii_wei_i_i_:¸

_o1'_ _i;(i_'_ _o_o_.

Slide the meat drawer temperature control forward to make the

meat drawer less cold or backward to make the drawer more

cold.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ................. use same day as purchased

Chicken, ground beef, variety meats (liver)............... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ........................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

_)_" _(i) "¸ _o I_o_ _ = _i)_Vi

To Remove and Replace the Wine Rack (left) or Can/Bottle

Rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

Depending on your model, you may have a one-, two- or

three-piece bin. Eggs may be stored in the egg tray or loose in

the bin.

NOTE: Store eggs in a covered container for long-term storage. If

your model does not have an egg storage bin, store eggs in their

original carton on an interior shelf.

FREEZERFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

To Remove and Replace the Shelf:

1. Remove the shelf by lifting the entire shelf slightly and move it

all the way to one side. Tilt the other side up and out of the

shelf supports.

2. Replace the shelf by inserting one end all the way into the

center of the shelf supports. Then, lower the other end of the

shelf and insert it into the shelf supports.

NOTE: The shelf should lower slightly and lock into place. Ifthe

shelf does not appear stable, make sure both ends of the shelf

are inserted into the shelf supports.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Seal the package

or container securely to prevent taste and odor transfer

throughout the product. Ice crystals inside a sealed package are

normal.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot [907-

1,350 g per 28 L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. The freezer door

must close tightly. For more information on preparing food for

freezing, check a freezer guide or reliable cookbook.

{ :

To Remove and Replace the Freezer Floor:

1. Lift both back "fences" up and out.

2. Remove the freezer floor by pulling it out about 1" (2.5 cm)

with one hand around the air tower section (center back) and

one hand at center front.

3. Lift up floor at rear until hooks release from cabinet and pull

the floor out the rest of the way.

4. Replace the freezer floor by sliding the floor straight in until

the hooks drop into place at rear of cabinet.

Replace "fences" by aligning pins with socket in the floor, and

pushing down until they snap into place.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To Remove and Replace the Rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To Remove and Replace the Rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

{ :

NOTE: Can racks may be purchased as an Accessory for some

models.

To Remove and Replace the Racks/Bins:

1. Remove the racWbin by lifting it and pulling it straight out.

2. Replace the racWbin by sliding it in above the desired

support and pushing it down until it stops.

io _ _i_o_ _ _i

The utility compartment and tray slide from one side to the other

for more flexible storage. The tray fits on either side of the utility

compartment or partially underneath it. Try moving it to different

positions to find the option that works best for you.

To Install and Adjust the Utility Compartment and Tray:

1. Insert the front of the utility tray into the slot on the back of

the shelf rail. Lower the back of the tray into position.

2. Place the front of the utility compartment on top of the shelf

rail. Lower the back of the compartment onto the ribs on the

refrigerator door.

Adjust the utility compartment by lifting the front slightly and

sliding it to the desired position. Lower the front to lock it into

place.

)

The shelf bottom flips up so you can store taller items inthe door

shelf below. When in the down position, the shelf is strong

enough to hold up to 10 Ibs. (4.5 kg).

REFRIGERATOR CARE

Explosion Hazard

Use nenflammabme cleaner°

Failure to de so can result in death, expmeeien, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to 0.95 L] of water).

4. Determine whether your refrigerator exterior is painted metal,

brushed aluminum or stainless steel and choose the

appropriate cleaning method.

Painted metal: Wash exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners, or cleaners designed for stainless steel.

Dry thoroughly with a soft cloth. For additional protection

against damage to painted metal exteriors, apply appliance

wax (or auto paste wax) with a clean, soft cloth. Do not wax

plastic parts.

Brushed aluminum: Wash with a clean sponge or soft cloth

and a mild detergent in warm water. Do not use abrasive or

harsh cleaners, or cleaners designed for stainless steel. Dry

thoroughly with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners. Dry thoroughly with a soft cloth.

To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner & Polish.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does

occur, clean plastic part with a sponge and mild detergent in

warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see the "Accessories" section.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" graphic or

"Base Grille" section.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace

the bulb with one of the same size, shape, and wattage.

1. Unplug refrigerator or disconnect power.

2. Remove the bulb from behind the control panel in the

refrigerator or from behind the light shield in the freezer (on

some models). Replace it with a bulb of the same wattage.

3. Plug in refrigerator or reconnect power.

If the power will be out for 24 hours or less, keep the door or

doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen for

2 to 4 days.

• If neither afood locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

Depending on the model, turn the Thermostat Control or

Refrigerator Control to OFR See "Using the Controls."

Clean refrigerator, wipe it, and dry well.

Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Thermostat Control or

Refrigerator Control to OFR See "Using the Controls."

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See "Adjust the Doors."

10. Tape the doors closed and tape the power cord to the

refrigerator cabinet.

When you get to your new home, put everything back and refer to

the "Installation Instructions" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power cord unplugged? Plug into a grounded 3 prong

outlet.

• Has a household fuse blown or circuit breaker tripped?

Replace the fuse or reset the circuit breaker.

• Is the Refrigerator Control turned to the OFF position?

See "Using the Control(s)," depending on the model.

• Is the refrigerator defrosting? Recheck to see whether the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

The lights do not work

• Is the power cord unplugged? Plug into agrounded 3 prong

outlet.

• Is a light bulb loose in the socket or burned out? See

"Changing the Light Bulb(s)," depending on the model.

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate. It is

normal for water to drip into the defrost pan.

• Is it more humid than normal? When it is humid, expect that

the water in the defrost pan will take longer to evaporate.

The motor seems to run too much

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room

temperatures, your motor will run about 40% to 80% of the

time. Under warmer conditions, it will run even more.

Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the

refrigerator back down.

Are the doors opened often? The motor will run longer

when this occurs. Conserve energy by getting all items out at

one time, keeping food organized, and closing the door as

soon as possible.

• Is the control set correctly for the surrounding

conditions? See "Using the Control(s)," depending on the

model.

• Are the doors closed completely? Close the doors firmly. If

they do not close completely, see "The doors will not close

completely" later in this section.

• Are the condenser coils dirty? This prevents air transfer and

makes the motor work harder. Clean the condenser coils. See

"Cleaning."

NOTE: Your new refrigerator will run longer than your old one due

to its high-efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See

"Normal Sounds."

The ice maker is not producing ice or not enough ice

• Has the ice maker just been installed? Wait 72 hours for full

ice production to begin. Once your refrigerator is cooled, the

ice maker should produce 70-120 cubes every 24 hours.

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after hookup for ice production. See "Using the

Control(s)," depending on the model.

Is the wire shutoff arm in the OFF (arm up) position?

Lower the wire shutoff arm to the ON (arm down) position.

See "Ice Maker."

Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve. See "Connect the Water

Supply."

Does the ice maker mold have water in it or has no ice

been produced? Be sure your refrigerator has been

connected to a water supply and the supply shutoff valve is

turned on. See "Connect the Water Supply."

Is an ice cube jammed in the ejector arm? Remove the ice

from the ejector arm with a plastic utensil. See "Ice Maker."

Has a large amount of ice just been removed? Allow

24 hours for ice maker to produce more ice.

Is the control set correctly? If too little ice is produced, see

"Using the Control(s)," depending on the model.

Is there a water filter installed on the refrigerator? The

filter may be full or incorrectly installed. Depending on your

model, remove the water filter cartridge. See "Water Filtration

System." Operate the dispenser. If the water flow increases

noticeably, your filter is full and needs to be replaced.

Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

Off-taste, odor or gray color in the ice

• Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

Have the ice cubes been stored too long? Throw old ice

away and make a new supply.

Has food in the refrigerator been wrapped properly? See

"Refrigerator Features."

Do the freezer and ice bin need to be cleaned? See

"Cleaning."

Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator?

Gray or dark discoloration in ice indicates that the water

filtration system needs additional flushing. Run additional

water through the water dispenser to flush the water filtration

system more thoroughly, at least 2 to 3 gal. (8 to 12 L) or

5 minutes initially. Discard discolored ice.

The water dispenser will not operate properly

Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to

depress the water dispenser until water begins to flow.

Dispense and discard 2 to 3 gal. (8 to 12 L) of water. This will

take approximately 5 minutes and will help clear air from the

line. Additional flushing may be required in some households.

See "Water Dispenser."

Is the water shutoff valve not turned on or the water line

connected at the source? Be sure the water shutoff valve is

turned on and the water source is connected to the

refrigerator. See "Connect the Water Supply."

Is the water shutoff valve clogged or incorrectly installed?

See "Connect the Water Supply." If clogging or installation is

not a problem, call for service or contact a plumber.

Is there a kink in the home water source line? Ifyou find or

suspect a kink in the water line, contact a licensed, qualified

plumber.

Is there a water filter installed on the refrigerator? The

filter may be clogged or incorrectly installed. First, check the

filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call for service.

Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

Water flow from the dispenser decreases noticeably

Is there a water filter installed on the refrigerator? The

filter may be full or incorrectly installed. Depending on your

model, remove the water filter cartridge. See "Water Filtration

System." Operate the dispenser. If the water flow increases

noticeably, your filter is full and needs to be replaced.

Water leaking from the dispenser

• Is the glass not being held under the water dispenser long

enough? Hold the container under the water dispenser 2 to

3 seconds after releasing the dispenser lever. Water may

continue to dispense during this time.

Is there a water filter installed on the refrigerator? The

water filtration system may have air in the lines, causing water

to drip. Additional flushing may help clear air from the lines.

Normal dispenser use should flush air from the lines within

24 to 72 hours.

The dispenser water is not cool enough

• Has the refrigerator been newly installed? Allow 24 hours

for the refrigerator to cool completely.

• Has a large amount of water been recently dispensed?

Allow 24 hours for the water to cool completely.

• Has water not been recently dispensed? The first glass of

water may not be cool. Discard the first glass of water.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the automatic

exterior moisture control.

La page charge ...

KitchenAid KTRA19EMBT00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KTRA19EMBT00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KTRA19EMBT00 Owner's manual

KitchenAid KTRA19EMBT00 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KTRA19EMBT00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents