KitchenAid KSRP22FNWH00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSRP22FNWH00

Catégorie: Frigos

Taper: Le manuel du propriétaire

TABLEOFCONTENTS

REFRIGERATOR SAFETY ............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Water Supply Requirements ........................................................ 5

Base Grille .................................................................................... 5

Door Removal ............................................................................... 6

Door Closing ................................................................................. 8

Water Supply Connection ............................................................ 8

Water System Preparation ......................................................... 10

Normal Sounds .......................................................................... 10

REFRIGERATOR USE .................................................................. 10

Ensuring Proper Air Circulation .................................................. 10

Using the Controls ..................................................................... 11

Water and Ice Dispensers .......................................................... 11

Water Filter Status Light ............................................................. 13

Water Filtration System .............................................................. 13

Ice Maker and Storage Bin ........................................................ 14

REFRIGERATOR FEATURES ...................................................... 15

Refrigerator Shelves ................................................................... 15

Flip-up Shelf ............................................................................... 16

Adjustable Flip-up Shelf ............................................................. 16

Drop-down shelf ......................................................................... 16

Dell Drawer ................................................................................. 16

Convertible Vegetable/Meat Drawer, Crisper and Covers ........16

Convertible Vegetable/Meat Drawer Temperature Control .......17

Crisper Humidity Control ........................................................... 17

Wine or Can/Bottle Rack ........................................................... 17

Utility Bin .................................................................................... 17

FREEZER FEATURES .................................................................. 18

Freezer Shelf .............................................................................. 18

Freezer Basket or Bin ................................................................. 18

DOOR FEATURES ........................................................................ 18

Tilt-out Freezer Door Bin............................................................ 18

Chilled Door Bin ......................................................................... 18

Door Rails ................................................................................... 19

Door Bins.................................................................................... 19

REFRIGERATOR CARE ............................................................... 19

Cleaning ...................................................................................... 19

Changing the Light Bulbs ........................................................... 20

Power Interruptions .................................................................... 21

Vacation and Moving Care ......................................................... 21

TROUBLESHOOTING .................................................................. 22

ASSISTANCE OR SERVICE ......................................................... 24

In the U.S.A ................................................................................ 24

In Canada ................................................................................... 25

Accessories ................................................................................ 25

WATER FILTER CERTIFICATIONS ............................................. 25

PRODUCT DATA SHEETS ........................................................... 26

WARRANTY .................................................................................. 27

TABLEDESMATIERES

SI:!:CURITE DU RI:!:FRIGERATEUR .............................................. 2g

Mise au rebut de votre vieux refrigerateur ................................. 29

INSTRUCTIONS D'INSTALLATION ............................................. 30

Deballage .................................................................................... 30

Emplacement d'installation ........................................................ 30

Specifications electriques .......................................................... 31

Specifications de I'alimentation en eau ..................................... 31

Grille de la base .......................................................................... 31

Enlevement des portes ............................................................... 32

Fermeture des portes ................................................................. 34

Raccordement de la canalisation d'eau .................................... 34

Preparation du syst_me d'eau ................................................... 36

Sons normaux ............................................................................ 36

UTILISATION DU REFRIGI:!:RATEUR .......................................... 37

Pour s'assurer d'une circulation d'air appropriee ...................... 37

Utilisation des commandes ........................................................ 37

Distributeurs d'eau et de glagons .............................................. 38

Le temoin lumineux de I'etat du filtre heau ............................... 40

Systeme de filtration d'eau ........................................................ 40

Machine a gla9ons et bac d'entreposage ................................. 41

CARACTI:!:RISTIQUES DU REFRIGERATEUR ........................... 42

Tablettes du refrigerateur ........................................................... 42

Tablette relevable ....................................................................... 43

Tablette relevable ajustable ....................................................... 43

Ctag_re inclinable ....................................................................... 43

Tiroir pour specialites alimentaires ............................................ 43

Tiroir a legumes/viande convertible,

bac a legumes et couvercles ..................................................... 43

Reglage de la temperature du tiroir

legumes/viande convertible ....................................................... 44

Reglage de I'humidite darts le bac a legumes ........................... 44

Casier a vin ou porte-cannettes/bouteilles ................................ 44

Casier utilitaire ............................................................................ 45

CARACTI:!:RISTIQUES DU CONGELATEUR ............................... 45

Tablette de congelateur ............................................................. 45

Panier ou bac de congelateur .................................................... 45

CARACTI:!:RISTIQUES DE LA PORTE ......................................... 45

Compartiment inclinable de la porte du congealateur .............. 45

Compartiment frafcheur ............................................................. 46

Tringles dans la porte ................................................................. 46

Balconnets dans la porte ........................................................... 46

ENTRETIEN DU REFRIGI:!:RATEUR ............................................ 47

Nettoyage ................................................................................... 47

Remplacement des ampoules d'eclairage ................................ 48

Pannes de courant ..................................................................... 49

Entretien avant les vacances ou Iors d'un demGnagement .......49

DI!:PANNAGE ................................................................................. 50

ASSISTANCE OU SERVICE ......................................................... 53

Accessoires ................................................................................ 53

FEUILLES DE DONNEES SUP LE PRODUIT ............................. 54

GARANTIE ..................................................................................... 55

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance, Always read and obey all

safety messages.

This is the safety alert symbol,

This symbol alerts you to potential hazards that can kill or hurt you and others,

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING," These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed,

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker (on

ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water

(on some models).

SAVE THESE INSTRUCTIONS

ProperDisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can resuJt in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors,

• Leave the shelves in place so that children may not easily

climb inside,

INSTAILATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the "Refrigerator Safety" section.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pulI the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the "Refrigerator Care" section.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many smal!, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

E×ploeion Hazard

Keep flammabJe materiaJs and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion,

or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2in.

(1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on

each side (depending on your model) to allow for the door to

swing open. If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

V2" (1.25 crn)

II -- 1

_Jl,

2" (5o08 cm)

ElectricaJ Shock Hazard

Plug into a grounded 3 prong outJet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can reeuJt in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Read all directions carefully before you begin.

IMPORTANT:

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Tools Required: Flat-blade screwdriver, 7_6in. and 1/2in. open-

end wrenches or two adjustable wrenches, 1/4in. nut driver and

drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a 1/4in.

(6.35 ram) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16in.

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207-827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

see "Troubleshooting" or call a licensed, qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the system needs to be

a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa) a booster pump can be inserted into

the small tubing that goes from the cold water line to the reverse

osmosis system.

If the water dispenser is still not dispensing water properly:

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

See "Water Filtration System."

If you have questions about your water pressure, refer to

"Troubleshooting" or call a licensed, qualified plumber.

To remove the base grille:

1. Open both doors.

2. Place hands along the ends of the grille. Push in on the top

and pull up on the bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille

after cleaning.

To replace the base grille:

1. Open both doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

TOOLSNEEDED:1/4in.hex-headsocketwrench,%6in.hex-headsocketwrenchandaflat-bladescrewdriver.

IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFEUnplugrefrigeratorordisconnectpower.Removefoodandany

adjustabledoororutilitybinsfromdoors.

NOTE:Itmayonlybenecessarytoremoveeitherthedoorhandleorthedoorstogetyourproductthroughthedoorwayofyourhome.

Measurethedooropeningtoseewhetheryouneedtoremovetherefrigeratorhandlesorthedoors.

Electrical Shock Hazard

Disconnect power before removing doors.

Reconnect both ground wires before operating.

Failure to do so can result in death or electrical shock.

Top Left Binge

Style 1

Style 2

1. Do Not Remove Screw

Water Dispenser

Tubing Connection

1, Red Outer Ring

Top Right Binge

1. Do Not Remove Screw

Handte

RemovaJ

(OptionaJ)

Door Alignment

1. Leveling Screw

Bottom Binge

1, Do Not Remove Screw

Handle Removal (optional)

Style 1

1. Apply firm pressure with your hand on the face of trim. Slide

top trim up and bottom trim down away from handle. Lift trim

pieces off shoulder screws (see Graphic 1).

NOTE: Some models include accent pieces between the handle

and the handle trim. If your model includes the accents, you will

need to carefully remove them with a flat-blade screwdriver

before removing the handle screws. The accent pieces are

optional and can be reinstalled or left off the handle assembly.

2. Remove handle screws and handles. (See Graphic 1).

3. Move refrigerator into place. Replace handles as shown (see

Graphic 1).

Style 2

1. Apply firm pressure on the handle to slide it up and off of the

shoulder screws (see Graphic 1).

2. Move refrigerator into place. Replace handles as shown (see

Graphic 1).

Door Removal

6. Disconnect wiring:

Style 1

• Disconnect wiring plug.

• Remove green ground wire screw to disconnect ground

wires.

1.Do not remove screw 1

2. Ground wires

3. Green ground wire screw

4. Wiring Plug

Style 2

• Disconnect wiring plug.

E_ectrica_ Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or

etectrica_ shock.

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by

pulling up on the bottom outside corners (see Graphic 2).

3. Close both doors and keep them closed until you are ready to

lift them free from the cabinet.

4. If you have a dispenser (ice or water), disconnect the water

dispenser tubing located behind the base grille on the freezer

door side (see Graphic 3).

• Press the red outer ring against the face of the fitting and

pull the dispenser tubing free.

• On some models, remove the tubing from the hose clip.

5. Remove the top left hinge cover and screws as shown (see

Graphic 4). Do not remove screw 1.

!. Do not remove screw 1

2. Wiring plug

7. Carefully lift the freezer door straight up and off of the bottom

hinge (see Graphic 5). The water dispenser tubing remains

attached to the freezer door and pulls through the bottom left

hinge. Make sure you protect the dispenser tubing from

damage.

8. Remove the top right hinge cover and screws as shown (see

Graphic 6). Do not remove screw 1.

9. Lift the refrigerator door straight up and off of the bottom

hinge.

10. It may not be necessary to remove the bottom hinge to move

the refrigerator through a doorway. Both bottom hinges have

similar construction. If necessary, disassemble the hinges as

shown (see Graphic 7). Do not remove screw 1.

Door and Hinge Replacement

1. Replace both bottom hinges, if removed. Tighten screws.

2. Assistance may be needed to feed the water dispenser

tubing through the bottom hinge while reinstalling the freezer

door. Carefully feed the dispenser tubing through the bottom

left hinge before replacing the door on the hinge.

NOTE: Provide additional support for the doors while the top

hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Reconnect water dispenser tubing by pushing tubing into

fitting until it stops and black mark touches face of fitting (see

Graphic 3). On some models, replace tubing in hose clip.

4. Alignandreplacethetoplefthingeasshown(seeGraphic4).

Tightenscrews.

ElectricaJShockHazard

Reconnectbothgroundwires.

Failuretodosocanresultindeathor

etectricaJshock.

Style1

• Reconnectbothgroundwires.

• Reconnectwiringplug.

!. Do not removescrew 1

2. Ground wires

3. Greenground wirescrew

4. Wiringplug

Style 2

• Reconnect wiring plug.

1.Do not remove screw 1

2. Wiringplug

5. Replace left hinge cover and screws.

6. Replace the refrigerator door by carefully lifting the door onto

the bottom right hinge.

7. Align and replace the top right hinge as shown (see

Graphic 6). Tighten screws.

8. Replace hinge cover and screws. Tighten screws.

9. Plug into a grounded 3 prong outlet.

Your refrigerator has two front adjustable rollers -- one on the

right and one on the left. If your refrigerator seems unsteady or if

you want the doors to close more easily, adjust the refrigerator's

tilt using the instructions below:

1. Move the refrigerator into its final position.

2. The two leveling screws are part of the front roller assemblies,

which are at the base of the refrigerator on either side (see

Graphic 8).

3. Use a hex-head socket wrench to adjust the leveling screws.

Turn the leveling screw to the right to raise that side of the

refrigerator or turn the leveling screw to the left to lower that

side. It may take several turns of the leveling screws to adjust

the tilt of the refrigerator (see Graphic 8).

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

4. Open both doors again and check to make sure that they

close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It

may take several more turns, and you should turn both

leveling screws the same amount.

5. Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFR

Connecting to Water Line

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

Locate a 1/2in. to 11/4in. (1.25 cm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of

the pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use 1/4in.

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4in. hole in the cold water pipe

you have selected.

.......... 1

7 ......................2

1.Cold waterpipe 5. Compression sleeve

2. Pipe clamp 6. Shutoff valve

3. Copper tubing 7.Packing nut

4. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4in. drilled hole

in the water pipe and that the washer is under the pipe clamp,

Tighten the packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown, Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply, Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Connecting to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut, Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help prevent

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the coupling on the end of the

copper tubing. Tighten the nut by hand, Then tighten it with a

wrench two more turns. Do not overtighten.

i 2 3 4 5

1.Line torefrigerator 4. Coupling (provided)

2. Nut (provided) 5. Ferrule (purchased)

3. Bulb 6. Nut (purchased)

4. Turn shutoff valve ON,

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4in, (6.35 mm) water line at either tube connection,

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section,

NOTE: Allow 24 hours to produce the first batch of ice, Allow

3 days to completely fill ice container.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown,

1. Tube clamp

2. Copper tubing

3. Compression nut

4. Valve inlet

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4in. (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section.

NOTE: Allow 24 hours to produce the first batch of ice. Allow

3 days to completely fill ice container.

1. Bulb

2. Nut (provided)

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

4. Turn shutoff valve ON,

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak,

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4in, (6.35 mm) water line at either tube connection,

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section,

NOTE: Allow 24 hours to produce the first batch of ice, Allow

3 days to completely fill ice container.

Pleasereadbeforeusingthewatersystem.

Immediatelyafterinstallation,followthestepsbelowtomake

surethatthewatersystemisproperlycleaned.

1. Openthefreezerdoorandturnofftheicemaker.ForStylef,

liftupthewireshutoffarmasshown.ForStyle2,movethe

switchtotheOFF(right)settingasshown.TheON/OFF

switchislocatedonthetoprightsideofthefreezer

compartment.

Style I

Style 2

NOTES:

• If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cap is in the

horizontal position.

• Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Open the freezer door and turn on the ice maker. For Style 1,

lower the wire shutoff arm. For Style 2, move the switch to

the ON (left) position. Please refer to the "Ice Maker and

Storage Bin" section for further instructions on the operation

of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a

popping noise.

• You may hear air being forced over the condenser by the

condenser fan.

• You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATORUSE

In order to ensure proper temperatures, you need to permit air to

flow between the two sections. Cold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator

section through the top vent. Air then returns to the freezer as

shown.

Do not block any of these vents with food such as soda, cereal,

bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer from food, wrap or cover foods tightly.

/iiY !iiii ii!iii!ilt:!:i;C iiii:: i!

For your convenience, your refrigerator controls are preset at the

factory. When installing your refrigerator, make sure that the

controls are still preset to the "mid-settings" as shown.

Style I

COLD

FREEZER

COLDER COLD

REFRRGERATOR

. 3 4 ,

1 6 COLDER

Style 2

3. Push the control in to lock it into place.

CONDITION/REASON: SETTING

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR

Control one setting

Not set correctly for your

conditions lower

REFRIGERATOR too warm REFRIGERATOR

Door opened often, large amount of Control one setting

food added or room temperature higher

very warm

FREEZER too cold FREEZER Control one

Not set correctly for your setting lower

conditions

FREEZER too warm/too little ice FREEZER Control one

Door opened often, or large amount setting higher

of food added or very cold room

temperature (can't cycle often

enough) or heavy ice usage

IMPORTANT:

• Your product will not cool when the Refrigerator Control is set

to OFR

The Refrigerator Control adjusts the refrigerator compartment

temperature. The Freezer Control adjusts the freezer

compartment temperature. Higher numbered settings make

the compartment colder. Lower numbered settings make the

temperature less cold.

• Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) setting will not cool the compartments any

faster.

• The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Adjusting the Controls

If you need to adjust temperatures, adjust the refrigerator

temperature first.

NOTE: Wait at least 24 hours between adjustments and then

recheck the temperatures.

Style 1

Turn the control to the right (clockwise) to make the compartment

colder or to the left (counterclockwise) to make it less cold.

Style 2

1. Push in on the control and release it.

2. The control will pop out. Turn the control to the desired

setting.

Cut Hazard

Use a sturdy g(ass when dispensing ice or water.

Fai)ure to do so can result in cuts.

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed

ice, a special light that turns on when you use the dispenser, a

special Night Light mode, or a lock option to avoid accidental

dispensing.

The ice dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the

ice bin. Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes

and the ice dispensing stops. The dispensing system will not

operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before

dispensing ice, select which type of ice you prefer. The button

controls are designed for easy use and cleaning.

Style 1 Style 2

ICE

CRUSH CUBE

For crushed ice, cubes are crushed before they are dispensed.

This may cause a slight delay when dispensing crushed ice.

Noise from the ice crusher is normal, and pieces of ice may vary

in size. When changing from crushed to cubed, afew ounces of

crushed ice will be dispensed along with the first cubes.

To dispense ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The water dispenser

If you did not flush the water system when the refrigerator was

first installed, press the water dispenser bar with a glass or jar

until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately

6 to 7 minutes of water after water begins dispensing. It will take

3 to 4 minutes for the water to begin dispensing. The water you

draw and discard cleans the system and helps clear air from the

lines. Allow several hours for the refrigerator to cool down and

chill water.

IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray.

The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned.

To dispense water:

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense enough water every week to

maintain a fresh supply.

The dispenser light

Style 1

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touch pad or rocker switch).

On some models: Whenever you use the dispenser the lever will

automatically turn the light on.

LIGHT

OFF O N

NOTE: See the "Changing the Light Bulbs" section for

information on changing the dispenser light bulb.

Style 2

When you use the dispenser, the lever will automatically turn the

light on. If you want the light to be on continuously, you may

choose either ON or NIGHT LIGHT.

NIGHT

ON LIGHT

ON: Press the LIGHT button to turn the dispenser light on.

NIGHT LIGHT: Press the LIGHT button a second time to select

the Night Light mode. The dispenser light will automatically

adjust to become brighter as the room brightens, dimmer as the

room darkens.

OFF: Press the LIGHT button a third time to turn the dispenser

light off.

The dispenser lights are LEDs which should not need to be

changed. If it appears that your dispenser lights are not working,

check to be sure that the light sensor is not blocked (in Night

Light mode). See "Troubleshooting" for more information.

The dispenser lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent

accidental dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product,

to the ice maker, or to the dispenser light. It simply deactivates

the dispenser levers.

Style 1

To turn off the dispenser, press the LOCK button until the

indicator appears. The ice and water dispensers will not work. To

unlock the dispenser, press the UNLOCK button until the

indicator appears. Then continue to dispense ice or water as

usual.

DISPENSER

LOCK UNLOCK

Style 2

To turn off the dispenser, press and hold the LOCK OUT button

until the indicator appears. The ice and water dispensers will not

work. To unlock the dispenser, press the LOCK OUT button until

the indicator disappears. Then continue to dispense ice or water

as usuaJ.

PRESS& HOLD

The water filter status light will help you know when to change

your water filter cartridge. The light will change from green to

yellow. This tells you that it is almost time to change the water

filter cartridge (90% of the filter life has been used). It is

recommended that you replace the base grille water filter

cartridge when the water filter indicator light changes to red OR

water flow to your water dispenser or ice maker decreases

noticeably. To change the base grille water filter cartridge, see

"Changing the Water Filter Cartridge" later in this section.

After changing the water filter cartridge, reset the water filter

status light.

Style 1

Press the light switch 5 times within 10 seconds. The status light

will change from red to green.

1. Status light

2. Light switch

Style 2

Press and hold the water filter reset button until the status light

turns green. Your reset button may be located on the water

dispenser or on the control panel in the refrigerator compartment.

Dispenser Control Panel

o •

PRESS& HOLD

Non-Indicator Water Filter (on some models)

If your refrigerator does not have the water filter status light, you

should change the water filter cartridge every 6 to 9 months

depending upon your usage. If the water flow to the water

dispenser or ice maker decreases noticeably before 6 months

have passed, replace the water filter cartridge more often.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

Changing the Water Filter Cartridge

The base grille water filter cartridge is located below the freezer

compartment door. Depending on your model, you may have a

filter that is installed behind the base grille (Style 1) or a filter that

is installed through the base grille (Style 2).

Style 1: Behind the base grille filter

1. Remove the base grille (see "Door Removal" section). Rotate

the cartridge counterclockwise to a vertical position and pull

the filter cartridge out.

NOTE: There will be water in the cartridge. Some spilling may

occur.

2. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

3. Push the new filter cartridge into the base until it stops.

Rotate the cartridge clockwise to a horizontal position. Flush

the water system (see "Flushing the Water System After

Replacing Filter" later in this section).

Style 2: Through the base grille filter

1. Locate the water filter cartridge cap in the front base grille.

Rotate the cap counterclockwise to a vertical position and

pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur.

2. Remove the cartridge cap by sliding it off the end of the old

cartridge. The cap will slide to the left or right. DO NOT

DISCARD THE CAR

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

Slide the cartridge cap onto the new cartridge. See

illustration in Step 2.

With cartridge cap in the vertical position, push the new filter

cartridge into the base grille until it stops. Rotate the cartridge

cap clockwise to a horizontal position. Flush the water

system (see "Flushing the Water System After Replacing

Filter" later in this section).

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until

the water begins to flow. Flush the water system by dispensing

and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the

system will take approximately 6 to 7 minutes and will help clear

air from the line. Additional flushing may be required in some

households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter cartridge. Your

water will not be filtered.

1. Remove the base grille water filter cartridge. For Style 1,

replace the base grille after removing the filter.

2. For Style 2, slide the cartridge cap off the end of the filter

cartridge. DO NOT DISCARD THE CAR With the cartridge

cap in the vertical position, insert the cap into the base grille

until it stops.

Rotate the cartridge cap to a horizontal position. The

cartridge cap might not be even with the base grille.

:J ,

Style 1

To turn the ice maker on/off:

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

To increase ice production rate:

MAX

Normal Ice Production: In normal ice production mode, the

ice maker should produce approximately 7 to 9 batches of ice

in a 24-hour period. If ice is not being made fast enough, turn

the Freezer Control toward a higher (colder) number in half

number steps. (For example, if the control is at 3, move it to

between 3 and 4.) Wait 24 hours between each increase.

Maximum Ice Production (on some models): In maximum ice

production, the ice maker should produce approximately 10

to 14 batches of ice in a 24-hour period. If your refrigerator

has the maximum ice production feature, push the switch to

MAX.

To remove and replace ice storage bin:

1. Pull the covering panel out from the bottom and then slide it

back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Style 2

To turn the ice maker on/off:

The ON/OFF switch is located on the top right side of the freezer

compartment.

1. Toturn the ice maker on, slide the control to the ON (left)

position.

NOTE: Your ice maker has an automatic shutoff. The ice

maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

To manually turn the ice maker off, slide the control to the

OFF (right) position.

To remove and replace the ice storage bin:

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out,

NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The

sensor cover ("flipper door") on the left wall of the freezer

stops the ice maker from producing ice if the door is open or

the storage bin is removed.

2. Replace the storage bin on the door and push down to make

sure it is securely in place.

Clean the Ice Storage Bin

Empty the ice container. Use warm water to melt the ice if

necessary.

NOTE: Never use anything sharp to break up the ice in the

bin. This can cause damage to the ice container and the

dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.

REMEMBER

• Allow 24 hours to produce the first batch of ice. Allow 3 days

to completely fill ice container.

• Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

• For Style 1 ice maker, do not force the wire shutoff arm up or

down.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATOR

FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

_mportant information to know about glass shelves

and cov_ra:

Do not ciean glass sheives or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This

reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models)

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the

frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check to make sure that

the shelf is securely in position.

To raise or lower the shelf:

1. Raise the shelf by pulling forward on the lever located at the

bottom front of the shelf and lift until the shelf locks into the

vertical position.

2. Lower the shelf until it is latched securely in place.

To raise or lower the shelf:

1. Raise the shelf by first sliding it back and down to make it

half-width. (You can use the shelf in this position to allow

taller items to be stored on the shelf below.)

2. Lift the front of the shelf until it fits securely in place against

the back wall. Lower the shelf securely back into position.

3. Pull the front of the shelf forward until it fits into place.

To remove and replace the drop-down shelf:

1. Remove the drop-down shelf by sliding it up and back. Pull

forward slightly to release the rear pegs from the track as

shown.

With the rear pegs released, pull the shelf down and forward.

Replace the shelf by sliding the front pegs into the track.

Push the shelf up and back until the rear pegs drop into the

track. Pull down and forward to be sure the shelf is securely

in place.

The dell drawer stores raisins, nuts, spreads, and other small

items at normal refrigerator temperatures.

To remove and replace the deli drawer:

1. Remove the dell drawer by sliding it straight out to the stop.

Lift the front and slide the drawer out the rest of the way.

Replace the dell drawer b sliding it back past the stop.

:i::ii

Crisper and Convertible Vegetable Meat Drawers

To remove and replace drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the

front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of

the way.

2. Replace the crisper or meat drawer by sliding it back in fully

past the drawer stop.

Crisper or Vegetable/Meat Drawer Covers

To remove and replace covers:

1. Remove the crisper and meat drawer. Press up in center of

crisper glass insert until it rises above the plastic frame.

Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame and remove. Repeat steps to remove

the meat drawer cover.

3. Replace back of meat drawer cover frame into supports or

slides on side walls of the refrigerator and lower or slide the

front of the cover frame into place.

4. Slide rear of glass insert into cover frame and lower front into

place. Repeat steps to replace the crisper cover.

The convertible vegetable/meat drawer can be adjusted to

properly chill meats or vegetables. The air inside the pan is

cooled to prevent "spot" freezing and can be set to keep meats

at the National Livestock and Meat Board recommended storage

temperatures of 28°- 32°F (-2°- 0°C).

IMPORTANT: To extend freshness, wrap meats in airtight,

moisture-proof materials before storing. Always store meat as

recommended.

Adjusting the control

The convertible control comes preset at the lowest meat setting.

To change a control setting: Move the control to the right

(colder) or to the left (less cold) as desired.

To store vegetables: Set the control to VEG (all the way to the

left) to store vegetables at their optimal storage temperatures

(which need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the left

(less cold). Remember to wait 24 hours between adjustments.

Doing so gives the temperature of the food time to change.

Meat storage guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ........................ use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ................ 1-2 days

Cold cuts, steaks/roasts .................................................. 3-5 days

Cured meats .................................................................. 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

To remove and replace the wine rack (left) or can/bottle

rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

NOTE: For long-term storage, place eggs in a covered container

or in their original carton on an interior shelf.

FREEZERFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

To remove and replace the shelf:

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

3. Replace shelf in the reverse order.

Frozen food storage guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot

[907-1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be careful to leave

enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

DOORFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

Remove and replace the bin:

1. Remove the bin by pulling out on the tabs behind the basket

to release it from the door liner.

2. Replace the bin by aligning the tabs with the buttons on the

sides of the door liner. Firmly snap the tabs onto the buttons

as shown.

Cool air from the freezer is directed to the refrigerator door bin

directly beneath the vents.

NOTE: The dairy compartment and can rack are not chilled.

The freezer basket or bin can be used to store bags of frozen

fruits and vegetables that may slide off freezer shelves.

To remove and replace the freezer basket or bin:

1. Remove basket or bin by sliding it out to the stop.

2. Lift the front of the basket or bin and slide it out the rest of the

way.

Chilled Door Bin Control

The chilled door bin control is located on the left-hand side of the

refrigerator compartment.

Replace the basket or bin by positioning it on the side wall

guide rails. Lift the basket or bin front slightly while pushing it

past the guide rail stops and slide basket or bin in the rest of

the way.

1, Door Chill control

Turn the control clockwise (right) to reduce the flow of cold air

to the bin and make it less cold.

Turn the control counterclockwise (left) to increase the flow of

cold air to the bin and make it colder.

REFRIGERATOR CARE

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

To remove and replace the door bins:

1. Remove the racWbin by lifting it and pulling it straight out.

2. Replace the rack/bin by sliding it in above the desired

support and pushing it down until it stops.

E×ploeion Hazard

Use nonflammable c_eaner.

Faiture to do so can result in death, e×ptoeion,

or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

Cleaning your refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g t0.95 L] of water).

4. Determine whether your refrigerator exterior is painted metal,

Satina TM stainless look finish, brushed aluminum or stainless

steel and choose the appropriate cleaning method.

NOTE: Satina TM stainless look finish has a smooth uniform

color with a glossy finish that resists fingerprints. Stainless

steel has a distinct grainy texture with variation in color that is

natural to steel.

Painted metal: Wash with a clean sponge or soft cloth and a

mild detergent in warm water. Do not use abrasive or harsh

cleaners, or cleaners designed for stainless steel. Dry

thoroughly with a soft cloth. For additional protection against

damage to painted metal exteriors, apply appliance wax (or

auto paste wax) with a clean, soft cloth. Do not wax plastic

parts.

Brushed Aluminum: Wash with a clean sponge or soft cloth

and a mild detergent in warm water. Do not use abrasive or

harsh cleaners, or cleaners designed for stainless steel. Dry

thoroughly with a soft cloth.

Satina TM stainless look finish: Wash with a clean sponge or

soft cloth and a mild detergent in warm water. Do not use

abrasive or harsh cleaners, or cleaners designed for stainless

steel. Dry thoroughly with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners. Dry thoroughly with a soft cloth.

To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner & Polish.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does

occur, clean plastic part with a sponge and mild detergent in

warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see the "Accessories" section.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every

2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" or "Door

Removal" section.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size and shape. The

dispenser light requires a heavy duty 10-watt bulb. All other lights

require a 40-watt appliance bulb. Replacement bulbs are

available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown.

NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,

shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

Dispenser Light (on some models}

Style 1

Reach through the dispenser area to remove and replace

light bulb.

...................1

1.DispenserLight

Style 2

The dispenser lights are LEDs which should not need to be

changed. If it appears that your dispenser lights are not working,

check to be sure that the light sensor is not blocked (in Night

Light mode). See "Troubleshooting" for more information.

Refrigerator Control Panel Light

Reach behind the refrigerator control panel to remove and

replace light bulb.

Crisper Lights

• If necessary, remove the top crisper drawer to gain access to

the crisper light shield. Remove the light shield by lifting the

ends out of the brackets as shown.

• Replace the light shield by inserting the ends into the

brackets. If necessary, replace the top crisper drawer.

Upper Freezer Light (on some models)

Style 1

• Remove light shield by grasping the top center of the shield

and pulling forward while turning it slightly to one side. If

necessary, remove top crisper drawer to access crisper light

shield.

Replace the light shield by inserting the tabs on one end into

the slotted holes in the refrigerator or freezer liner. Then,

carefully bend the shield at the center to insert the tabs on

the other end.

Style 2

• Remove the light shield by grasping the sides and squeezing

in toward the center and while pulling forward the shield.

• Replace the light shield by fitting the tabs into the slotted

holes in the freezer liner. Push in the shield until it snaps into

place.

La page charge ...

KitchenAid KSRP22FNWH00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSRP22FNWH00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KSRP22FNWH00 Owner's manual

KitchenAid KSRP22FNWH00 Le manuel du propriétaire

KitchenAid KSRP22FNWH00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents