KitchenAid KSRA22ILBL00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSRA22ILBL00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Kitchen_kid _

SIDE BY SIDE REFRIGERATOR

i!llii_,,:_,_,:i?,,i!!!ii:i:_iiillii_i:__!_i_ii!¸_iiiilliii:i¸_i_:i_iii_ii:i!i!ii_::!!_

For questions about features, operation/performance, pares accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www. KitchenAid.ca

REFRIGERATEUR COTE A COTE

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777 ou visitez notre site web &...

www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 2

2255706

TABLE OF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Water Supply Requirements ........................................................ 5

Base Grille .................................................................................... 5

Door Removal ............................................................................... 6

Door Closing ................................................................................. 8

Water Supply Connection ............................................................ 8

Water System Preparation ........................................................... 9

Factory Trim Kit .......................................................................... 10

Normal Sounds .......................................................................... 11

REFRIGERATOR USE .................................................................. 12

Ensuring Proper Air Circulation .................................................. 12

Using the Controls ..................................................................... 12

Water and Ice Dispensers .......................................................... 14

Water Filter Status Light............................................................. 15

Water Filtration System .............................................................. 15

Ice Maker and Storage Bin ........................................................ 16

REFRIGERATOR FEATURES ...................................................... 17

Refrigerator Shelves ................................................................... 17

Flip-up Shelf ............................................................................... 18

Adjustable Flip-up Shelf ............................................................. 18

Dell Drawer ................................................................................. 18

Convertible Vegetable/Meat Drawer, Crisper and Covers ........18

Convertible Vegetable/Meat Drawer Temperature Control .......18

Crisper Humidity Control ........................................................... 19

Wine or Can/Bottle Rack ........................................................... 19

Utility Bin .................................................................................... 19

FREEZER FEATURES .................................................................. 19

Freezer Shelf .............................................................................. 19

Freezer Basket or Bin ................................................................. 20

DOOR FEATURES ........................................................................ 20

Door Rails ................................................................................... 20

Can Racks and Door Bins .......................................................... 20

REFRIGERATOR CARE ............................................................... 20

Cleaning ...................................................................................... 20

Changing the Light Bulbs ........................................................... 21

Power Interruptions .................................................................... 22

Vacation and Moving Care ......................................................... 22

TROUBLESHOOTING .................................................................. 23

ASSISTANCE OR SERVICE ......................................................... 26

In the U.S.A ................................................................................ 26

In Canada ................................................................................... 27

Accessories ................................................................................ 27

WATER FILTER CERTIFICATIONS ............................................. 27

PRODUCT DATA SHEETS ........................................................... 28

WARRANTY .................................................................................. 29

TABLE DES MATIERES

S¢:CURITI_ DU RC:FRIGI_RATEUR .............................................. 30

INSTRUCTIONS D'INSTALLATION ............................................. 31

Deballage .................................................................................... 31

Emplacement d'installation ........................................................ 31

SpGcifications electriques .......................................................... 32

Specifications de I'alimentation en eau ..................................... 32

Grille de la base .......................................................................... 32

Enlevement des portes ............................................................... 33

Fermeture des portes ................................................................. 35

Raccordement de la canalisation d'eau .................................... 35

Preparation du systGme d'eau ................................................... 37

Ensembles decoratifs de I'usine ................................................ 38

Sons normaux ............................................................................ 39

UTILISATION DU RCFRIGI_RATEUR .......................................... 40

Pour s'assurer d'une circulation d'air appropriee ...................... 40

Utilisation des commandes ........................................................ 40

Distributeurs d'eau et de glagons .............................................. 42

Le t_moin lumineux de I'etat

du filtre a eau.............................................................................. 44

SystGme de filtration d'eau ........................................................ 44

Machine a glagons et bac d'entreposage ................................. 45

CARACTI_RISTIQUES DU RCFRIGCRATEUR ........................... 47

Tablettes du refrigerateur ........................................................... 47

Tablette relevable ....................................................................... 47

Tablette relevable ajustable ....................................................... 47

Tiroir pour specialites alimentaires ............................................ 48

Tiroir a legumes/viande convertible,

bac a legumes et couvercles ..................................................... 48

Reglage de la temperature du tiroir

legumes/viande convertible ....................................................... 48

Reglage de I'humidite dans le bac a legumes ........................... 49

Casier a vin ou porte-cannettes/bouteilles ................................ 49

Casier utilitaire ............................................................................ 49

CARACTI_RISTIQUES DU CONGI_LATEUR ............................... 49

Tablette de congelateur ............................................................. 49

Panier ou bac de congelateur .................................................... 50

CARACTI_RISTIQUES DE LA PORTE ......................................... 50

Tringles dans la porte ................................................................. 50

Porte-cannettes et balconnets ................................................... 50

ENTRETIEN DU RCFRIGI_RATEUR ............................................ 51

Nettoyage ................................................................................... 51

Remplacement des ampoules d'eclairage ................................ 52

Pannes de courant ..................................................................... 53

Entretien avant les vacances ou Iors d'un demenagement .......53

DC:PANNAGE ................................................................................. 54

ASSISTANCE OU SERVICE ......................................................... 57

Accessoires ................................................................................ 57

FEUILLES DE DONNI_ES SUR LE PRODUIT ............................. 58

GARANTIE ..................................................................................... 59

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance, Always read and obey all

safety messages.

This is the safety alert symbol,

This symbol alerts you to potential hazards that can kill or hurt you and others,

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING," These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed,

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker (on

ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water

(on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of

Your Old Refrigerator

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers, Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the "Refrigerator Safety" section.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cieaning or service, be sure to protect the floor.

Always pulI the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the "Refrigerator Care" section.

_mportant information to know about glass shemves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold= Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping=

For your protection, tempered glass is designed to shatter

into many smal!, pebble=size pieces. This is normal= GIass

shelves and covers are heavy= Use special care when re=

moving them to avoid impact from dropping=

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion,

or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2in.

(1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on

each side (depending on your model) to allow for the door to

swing open. If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

V2" (1.25 crn)

II -- I!

2" (5,08 cm)

ElectricaJShockHazard

Plugintoagrounded3 prong outJet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or eJectrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Read all directions carefully before you begin.

IMPORTANT:

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Tools Required: Flat-blade screwdriver, 7_6in. and 1/2in. open-

end wrenches or 2 adjustable wrenches, 1/4in. nut driver and drill

bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a 1/4in.

(6.35 ram) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/1_in.

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207-827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

see "Troubleshooting" or call a licensed, qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the system needs to be

a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa), a booster pump can be inserted into

the small tubing that goes from the cold water line to the reverse

osmosis system.

If the water dispenser is still not dispensing water properly:

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

See "Water Filtration System."

If you have questions about your water pressure, refer to

"Troubleshooting" or call a licensed, qualified plumber.

To remove the base grille:

1. Open both doors.

2. Place hands along the ends of the grille. Push in on the top of

the base grille and pull up on the bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille

after cleaning.

To replace the base grille:

1. Open both doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

TOOLSNEEDED:1/4in.,1/2in.,and%6in.hex-headsocketwrenches,afiat-bladescrewdriverandaPhillipsscrewdriver.

IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFF,unplugrefrigeratorordisconnectpower.Removefoodandany

adjustabledoororutilitybinsfromdoors.

Electrical Shock Hazard

Disconnect power before removing doors.

Reconnect both ground wires before operating.

Failure to do so can result in death or electrical shock.

Top Left Hinge

1 _tyle 1

1. Do Not Remove Screw

Water Dispenser

Tubing Connection

Door RemovaJ

Top Right Hinge

1 3 I

1, Do Not Remove Screw

Bottom Hinge

1, Do Not Remove Screw

Door Alignment

Door Removal

E_ectrica_ Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or

etectrica_ shock.

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by

pulling up on the bottom outside corners (see Graphic 1),

3. Close both doors and keep them closed until you are ready to

lift them free from the cabinet.

4. If you have a dispenser (ice or water), disconnect the water

dispenser tubing located behind the base grille on the freezer

door side (see Graphic 2).

• Press the red outer ring against the face of fitting and pull

the dispenser tubing free,

• On some models, remove tubing from hose clip,

5. Remove top left hinge screw and cover as shown (see

Graphic 3).

6. Disconnect wiring:

Style 1

• Disconnect wiring plug.

• Remove green ground wire screw to disconnect ground

wires,

Style 2

• Disconnect wiring plug.

1 _ 2

1.Do not remove screw 1

2. Wiringplug

7. Remove remaining left hinge screws and hinge as shown (see

Graphic 3), Do not remove screw 1.

8. Carefully lift freezer door straight up off bottom hinge (see

Graphic 4), The water dispenser tubing remains attached to

the freezer door and pulls through the bottom left hinge.

Make sure you protect the dispenser tubing from damage.

9. Remove top right hinge cover and screws as shown (see

Graphic 5). Do not remove screw 1.

10. Lift the refrigerator door straight up off bottom hinge.

11. It may not be necessary to remove the bottom hinge to move

the refrigerator through a doorway. Both bottom hinges have

similar construction.

• Disassemble the hinges as shown (see Graphic 6).

Do not remove screw 1.

1. Replace both bottom hinges, if removed. Tighten screws.

2. Assistance may be needed to feed the water dispenser

tubing through the bottom hinge while reinstalling the freezer

door. Carefully feed the dispenser tubing through the bottom

left hinge before replacing the door on the hinge.

NOTE: Provide additional support for the doors while the top

hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Reconnect water dispenser tubing by pushing tubing into

fitting until it stops and black mark touches face of fitting (see

Graphic 2). On some models, replace tubing in hose clip.

1. Do not remove screw 1

2. Ground wires

3. Green ground wire screw

4. Wiring plug

4. Align and replace the top left hinge as shown (see Graphic 3).

Tighten screws.

EtectricaJ Shock Hazard

Reconnect both ground wires.

Failure to do so can resuJt in death or

electricaJ shock.

Style 1

• Reconnect both ground wires.

• Reconnect wiring plug.

Style 2

1. Do not remove screw !

2. Ground wires

3. Green ground wire screw

4. Wiring plug

• Reconnect wiring plug.

1 _ 2

1.Do not remove screw 1

2. Wiringplug

Replace left hinge cover and screws.

Replace the refrigerator door by carefully lifting the door onto

the bottom right hinge.

Align and replace the top right hinge as shown (see

Graphic 5). Tighten screws.

Replace hinge cover and screws. Tighten screws.

Plug into a grounded 3 prong outlet.

Your refrigerator has two front adjustable rollers -- one on the

right and one on the left. If your refrigerator seems unsteady or if

you want the doors to close more easily, adjust the refrigerator's

tilt using the instructions below:

1. Move the refrigerator into its final position.

2. The two leveling screws are part of the front roller assemblies

which are at the base of the refrigerator on either side (see

Graphic 7).

Use a hex-head socket wrench to adjust the leveling screws.

Turn the leveling screw to the right to raise that side of the

refrigerator or turn the leveling screw to the left to lower that

side. It may take several turns of the leveling screws to adjust

the tilt of the refrigerator (see Graphic 7).

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

4. Open both doors again and check to make sure that they

close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It

may take several more turns, and you should turn both

leveling screws the same amount.

5. Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Read all directions before you begin.

IMPORTANT: Ifyou turn the refrigerator on before the water line

is connected, turn the ice maker OFR

Connecting to Water Line

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

Locate a 1/2in. to 11/4in. (1.25 cm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of

the pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use 1/4in.

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4in. hole in the cold water pipe

you have selected.

............... 1

7 ......................2

...... 3

1.Cold waterpipe 5. Compression sleeve

2. Pipe clamp 6. Shutoff valve

3. Copper tubing 7.Packingnut

4. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4in. drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Connecting to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help prevent

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

NOTE: Allow 24 hours to produce the first batch of ice. Allow

3 days to completely fill ice container.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

F/ II

!. Tube clamp

2. Copper tubing

3. Compression nut

4. Valve inlet

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4in. (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section.

NOTE: Allow 24 hours to produce the first batch of ice. Allow

3 days to completely fill ice container.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the coupling on the end of the

copper tubing. Tighten the nut by hand. Then tighten it with a

wrench 2 more turns. Do not overtighten.

i 2 3 4 5 6

1.Line to refrigerator 4. Coupling (purchased)

2. Nut (provided) 5.Ferrule (purchased)

3. Bulb 6. Nut (purchased)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4in. (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section.

1. Bulb

2. Nut (provided)

NOTE: Tighten the nut by hand. Then tighten it with a wrench

2 more turns. Do not overtighten.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4in. (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section.

NOTE: Allow 24 hours to produce the first batch of ice. Allow

3 days to completely fill ice container.

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. For Style 1

lift up the wire shutoff arm as shown. For Style 2 move the

switch to the OFF (right) setting as shown. The ON/OFF

switch is located on the top right side of the freezer

compartment.

Style 1

Style 2

NOTES:

• If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cap is in the

horizontal position.

• Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Open the freezer door and turn on the ice maker. For Style 1

lower the wire shutoff arm. For Style 2 move the switch to the

ON (left) position. Please refer to the "Ice Maker and Storage

Bin" section for further instructions on the operation of your

ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

(O)i_!_i;;O_i;;i_£__!);i_i_O<iii_!_i!i_i_ii_¸

There may be an occasion when you will need to remove the

factory-installed trim kit, such as moving the refrigerator to a new

home or installing custom-made decorator panels. Please read

all instructions carefully before removing the trim kit and

decorator panels.

Freezer Door Refrigerator Door

==,_1

.......................3 .......................

1. Decorator Panels

2. Filler Panels

3. Handles

Removing the Door Panels

NOTE: When removing and replacing decorator panels, only the

handle is removed. All other trim pieces remain attached to the

doors.

1. Remove the refrigerator and freezer handles:

• Using a Phillips screwdriver, remove the screws that hold

each handle in place.

• Lift off handle. Make sure you keep screws for reattaching

handles.

2. Remove the door panels:

• Open refrigerator or freezer door.

• Slide out decorator panel and filler board.

• Repeat process for other panels and filler boards.

• Store panel and filler boards carefully to prevent

scratching.

Replacing the Door Panels

1. Replace the refrigerator or freezer door panels:

• Open refrigerator or freezer door.

• Carefully slide the 1/8in. (3.18 mm) decorator panel into

place behind the side trim.

• Push the filler board into place behind the decorator

panel.

• Repeat process for other panels and filler boards.

2. Attach the handles:

NOTE: Freezer door handle is notched to fit around the dispenser

panel.

• Align the top of the refrigerator or freezer handle flush

with the top trim. Fasten the handle to the refrigerator or

freezer door with the screws, using a Phillips screwdriver.

• Repeat the process for the other handle.

Care of Decorator Panels

1. Clean panels with an anti-static cleaner (available in

electronics or computer departments) or mild soap and water

with a clean, soft, damp cloth.

2. Rinse panels thoroughly and blot dry using a dry, soft cloth or

chamois.

NOTE: Do not use paper towels or cleaners which contain

solvents such as ammonia. They can damage the surface of

the panels.

3. If small scratches should appear on the panels, they may be

filled using an automotive paste wax (NOT a cleaner/wax

combination). Apply wax sparingly and buff lightly with a

clean, soft cloth using a circular motion.

Installing Custom Wood Panels

Ifyou plan to install custom wood decorator panels, you will need

to create the panels yourself or consult your cabinetmaker or

carpenter. See dimensional drawings for wood panel inserts.

Flat panels:

You can create a custom flat panel a maximum of 1/4in. (6.35 mm)

thick to replace your decorator panels. Flat wood panels less

than 1/4in. (6.35 mm) thick are not recommended.

Raised panels:

A raised panel design can be created by screwing or gluing wood

panels to 1/4in. (6.35 mm) backing or by using 3/4in. (19.05 mm)

stock with routed edges.

Weight requirements for raised panel inserts:

• Refrigerator door panel should not exceed 25 Ibs.

(9.98 kg).

• Freezer door panels should not exceed 18 Ibs. (6.80 kg)

combined weight.

Dimensions for Custom Wood Panels:

22 cu. ft. Freezer and Refrigerator door

1/4"

(6.35 ram)

(7.93 ram)

18_/_2"

1/4,,

(7.93 ram)

q_-- 1915h6" _

I (80.7 cm)

(6.35 ram)

31/4" 3/4" mln. 3/4.

82.55mmmln. 16.05mmmln. ,16.05mm,

TOPWEW t t

1/4"

(6.35mm)

25 cu. ft. Freezer and Refrigerator door

5/16" /

(7.93 ram)

3/4"mln.

(1g.05mmmln.)

1/4,,

(6.38 mm)

_'_-"'" T

(53.7 cm)

..... j

153h6,,

(38.6 cm)

8311/16"

153/16" H (181.8 cnl)

(38.6 cm)

(71.3 cm)

(8.35 ram)

31/4"

TOP VIEW

1/4"

(6.38mm)

1/4,,

;(50.7 cm)

(6.35 ram)

3V4" 3/4"min.

(82.55mmmln.)(16.05mmmln.) _/4"

(19.05mm)

, i , ,

TOP VIEW t t

(6.35mm)

Dimensions for Routing Handle Side of Door Panel

(End View)

Route entire areasof handle side of panels 31/4in. (8.25cm).

-O

:32

31/4"

-<_ (8.25 cm)

min, !_ I Hinge Side

__]

= _ [ Door Door LH _

V4"(6ram) max. Panel Panel

2" (5 cm) 1"

min. (2.54 cm)

!. Handle

2. Door panel

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a

popping noise.

• You may hear air being forced over the condenser by the

condenser fan.

• You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit air to

flow between the two sections. Cold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator

section through the top vent. Air then returns to the freezer as

shown.

Slide Controls (on some models)

For your convenience, your controls are preset at the factory.

When installing your refrigerator, make sure that the controls are

still preset to the "mid-settings" as shown.

Style 1

Freezer Refrigerator

C )

cold 1 2 A 3 4 colder off 1 2 A 3 4 colder

Style 2

Freezer Refrigerator

Off I 2 A 3 4 Colder Cold I 2 _, 3 4 Colder

IMPORTANT:

• For Style 1, your product will not cool when the Refrigerator

control is set to OFR For Style 2, your product will not cool

when the Freezer Control is set to OFR

Do not block any of these vents with food such as soda, cereal,

bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly. •

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer from food, wrap or cover foods tightly.

Settings to the left of the mid-setting make the temperature

less cold. Settings to the right of the mid-setting make the

temperature colder.

The Automatic Exterior Moisture control continuously guards

against moisture buildup on the outside of your refrigerator

cabinet. This control does not have to be set or adjusted.

Adjusting Slide Controls

Your model may have Slide Controls or Digital Controls.

IMPORTANT (All Controls):

• The Refrigerator control adjusts the refrigerator compartment

temperature. The Freezer control adjusts the freezer

compartment temperature.

• Wait 24 hours after you turn on the refrigerator before you put

food into it. Ifyou add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer controls to a

lower (colder) setting will not cool the compartments any

faster.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

• The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

If you need to adjust temperatures:

• Slide the FREEZER or REFRIGERATOR control, one setting to

the right or left depending on the needed temperature

change.

NOTE: For Style 1, after adjusting the refrigerator

temperature, wait 24 hours and then recheck the FREEZER

temperature before making additional adjustments.

CONDITION: SETTING ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control

Not set correctly for conditions one setting lower

REFRIGERATOR too warm REFRIGERATOR Control

High use or room very warm one setting higher

FREEZER too cold FREEZER Control one

Not set correctly for conditions setting lower

FREEZER too warm/too little FREEZER Control one

ice setting higher

High use or heavy ice usage

Digital Controls (on some models)

For your convenience, your controls are preset at the factory.

When installing your refrigerator, make sure that the controls are

still preset to the "mid-settings" as shown. The digital control

panel is located at the top of the refrigerator compartment.

NOTE: The factory recommended set points are 0°F (-18°C) for

the freezer and 37°F (3°C) for the refrigerator.

To turn refrigerator on and view set points:

• Press and hold POWER (ON/OFF) pad for 2 seconds.

Warmer FREEZER REFRIGERATORWarmer

Power -

Colder Colder

NOTE: After the refrigerator is turned on, the Over Temperature

audio alarm and indicator light will activate every 11/2hours until

the refrigerator and freezer temperatures are below 48°F (9°C)

and 15°F (-9°C), respectively. To turn off the alarm and indicator

light, press the OVER TEMPERATURE (RESET) pad. (See the

"Over Temperature (Reset)" section.)

To view the Celsius temperatures:

• Press the °C SELECT pad. The indicator will light up. To

redisplay degrees in Fahrenheit, press the °C SELECT pad

again.

°C

NOTE: If the freezer temperature is below zero, the negative sign

next to the freezer display will light up.

Adjusting Digital Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To adjust set point temperatures:

• Press the refrigerator or freezer PLUS (+) or MINUS (-) pad

until the desired temperature is reached.

REFRIGERATOR Warmer

Colder

The set point range for the freezer is -5°F to 5°F (-21 °C to -15°C).

The set point range for the refrigerator is 33°F to 41°F

1°C to 5°C).

CONDITION/REASON: "TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control 1°

Not set correctly for conditions higher

REFRIGERATOR too warm REFRIGERATOR Control 1°

High use or room very warm lower

FREEZER too cold FREEZER Control 1° higher

Not set correctly for conditions

FREEZER too warm/too little FREEZER Control 1° lower

ice

High use or heavy ice use

Additional Digital Control Panel Features

Additional features are located on the control panel at the top of

the refrigerator compartment.

Water Filter Indicator Light and Reset

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

The water filter display will help you know when to change your

water filter cartridge. To change your filter, see the "Changing the

Water Filter Cartridge" section.

GOOD (green) New filter installed

ORDER (yellow) Order filter, 10% filter life remains

CHANGE (red) OR when Replace water filter

water flow decreases

• After changing the water filter, press RESET and hold for

2 seconds. The indicator light will change from Change (red)

to Good (green) when the system is reset.

FilterIndicator

• Good •

Water

• Order Filter

: (_esel)

• Change

Max Cool

The Max Cool feature assists with periods of heavy ice usage, full

grocery loads, or temporarily warm room temperatures.

• Press MAX COOL pad to turn on the Max Cool feature. The

Max Cool indicator light will remain on for 24 hours unless

manually turned off.

NOTE: The temperature display will not change. After

24 hours, the refrigerator returns to the previous temperature

set points.

Accelerated Ice Production (on some models)

This feature assists with temporary periods of heavy ice use by

increasing ice production over a 24-hour period.

• Press OPTIMICE touch pad to turn on the Optimlce TM feature.

The Optimlce TM setting will remain on for 24 hours unless

manually turned off.

Opiirn]ce

_i!i!i

If increased ice production is desired at all times, set the

Freezer Control to a colder number. Setting the freezer to a

colder temperature may make some foods, such as ice

cream, harder.

Over Temperature Reset (on some models)

The Over Temperature feature is designed to let you know when

either the refrigerator temperature rises above 48°F (9°C) or the

freezer temperature rises above 15°F (-9°C) for longer than

11/2hours. The audio alarm will shut off automatically when the

temperature returns to normal, but the indicator light will continue

to flash to let you know that an over temperature condition has

occurred.

IMPORTANT: Ifthe Over Temperature Alarm activates, your food

may spoil. See the "Power Interruptions" section for more

information and minimize door openings until temperatures return

to normal.

• Press OVER TEMPERATURE (RESET) pad to turn off the

audio alarm and flashing indicator light.

Over

• The Over Temperature (Reset) feature will continue to activate

every 11/2hours until refrigerator and freezer temperatures are

below 48°F (9°C) and 15°F (-9°C), respectively.

Temperature System

The Temperature System feature lets you know the compressor

or evaporator fan is running. It is normal for this indicator light to

be on.

Temperature

System

Cut Hazard

Use a sturdy gJass when dispensing ice or water.

Failure to do so can result in cuts.

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed

ice, a special light that turns on when you use the dispenser, or a

lock option to avoid accidental dispensing.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the

ice bin. Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes

and the ice dispensing stops. The dispensing system will not

operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before

dispensing ice, select which type of ice you prefer. The button

controls are designed for easy use and cleaning.

ICE

CRUSH CUBE

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from CRUSH to CUBE, a few ounces of crushed

ice will be dispensed along with the first cubes.

To dispense ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser, Pressing hard

will not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The Water Dispenser

If you did not flush the water system when the refrigerator was

first installed, press the water dispenser bar with a glass or jar

until you draw and discard 2to 3 gal. (8 to 12 L) or approximately

6 to 7 minutes of water after water begins dispensing. It will take

3 to 4 minutes for the water to begin dispensing. The water you

draw and discard cleans the system and helps clear air from the

lines. Allow several hours for the refrigerator to cool down and

chill water.

IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray.

The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned.

To dispense water:

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense enough water every week to

maintain a fresh supply.

The Dispenser Light

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touchpad or rocker switch).

On some models: Whenever you use the dispenser, the lever will

automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for

information on changing the dispenser light bulb.

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent

accidental dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the

refrigerator, to the ice maker, or to the dispenser light. It simply

deactivates the dispenser levers.

To turn off the dispenser, press the LOCK button. The indicator

will appear above the LOCK button and the ice and water

dispensers will not work. To unlock the dispenser, press the

UNLOCK button until the indicator appears. Then continue to

dispense ice or water as usual.

DISPENSER

LOCK UNLOCK

...... ...... ;

The water filter status light, located at the top of the refrigerator

compartment, will help you know when to change your water

filter cartridge.

Style I - Standard status light (on some models)

When the water filter status light changes from green to yellow,

this tells you that it is almost time to change the water filter

cartridge (90% of the filter life has been used). It is recommended

that you replace the base grille water filter cartridge when the

water filter indicator light changes to red OR water flow to your

water dispenser or ice maker decreases noticeably. See

"Changing theWater Filter Cartridge" later in this section.

!. Status Light

2. Light Switch

After changing the water filter cartridge, reset the water filter

status light by pressing the light switch 5 times within

10 seconds. The water filter status light will change from red to

green when the system is reset.

Style 2 - Digital status light (on some models)

A new water filter should display a Good (green) status. As the

filter life is used, the light will change from Good (green) to

Order (yellow). This tells you that it is almost time to change the

water filter cartridge (90% of the filter life has been used). It is

recommended that you replace the base grille water filter

cartridge when the water filter indicator light changes to Change

(red) OR when water flow to your water dispenser or ice maker

decreases noticeably. To change the water filter cartridge, see

"Changing the Water Filter Cartridge" later in this section.

Filter Indicator

• Good •

• Order

•Change

After changing the water filter cartridge, reset the water filter

indicator by pressing and holding the WATER FILTER (RESET)

pad for 2 seconds. The status light will change from Change (red)

to Good (green) when the water filter indicator is reset.

Non-indicator Water Filter (on some models}

If your refrigerator does not have the water filter status light, you

should change the water filter cartridge every 6 to 9 months

depending upon your usage. If the water flow to the water

dispenser or ice maker decreases noticeably before 6 months

have passed, replace the water filter cartridge more often.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

Changing the Water Filter Cartridge

Locate the water filter cartridge cap in the front base grille.

Rotate the cap counterclockwise to a vertical position and

pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur,

2. Remove the cartridge cap by sliding it off the end of the old

cartridge. The cap will slide to the left or right. Do not discard

the cap.

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

Slide the cartridge cap onto the new cartridge. See

illustration in Step 2.

With cartridge cap in the vertical position, push the new filter

cartridge into the base grille until it stops. Rotate the cartridge

cap clockwise to a horizontal position. Flush the water

system (see "Flushing the Water System After Replacing

Filter" section).

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until

the water begins to flow. Flush the water system by dispensing

and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the

system will take approximately 6 to 7 minutes and will help clear

air from the line. Additional flushing may be required in some

households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

Using the Dispenser Without the Water Filter Cartridge

You can run the dispenser without a water filter cartridge. Your

water will not be filtered.

1. Remove the base grille water filter cartridge.

2. Slide the cartridge cap off the end of the filter cartridge. Do

not discard the cap. With the cartridge cap in the vertical

position, insert the cap into the base grille until it stops.

3. Rotate the cartridge cap to a horizontal position. The

cartridge cap might not be even with the base grille.

Style 1

To turn the ice maker on/off:

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

To increase ice production rate:

MAX

Normal Ice Production: In normal ice production mode, the

ice maker should produce approximately 7 to 9 batches of ice

in a 24-hour period. If ice is not being made fast enough, turn

the Freezer Control toward a higher (colder) number in half

number steps. (For example, if the control is at 3, move it to

between 3 and 4.) Wait 24 hours between each increase.

Maximum Ice Production (on some models): In maximum ice

production, the ice maker should produce approximately 10

to 14 batches of ice in a 24-hour period. If your refrigerator

has the maximum ice production feature, push the switch to

MAX.

To remove and replace ice storage bin:

1. Pull the covering panel out from the bottom and then slide it

back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Style 2

To turn the ice maker on/off:

The ON/OFF switch is located on the top right side of the freezer

compartment.

1. Toturn the ice maker on, slide the control to the ON (left)

position.

NOTE: Your ice maker has an automatic shutoff. The ice

maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the

OFF (right) position.

To remove and replace the ice storage bin:

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out,

NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The

sensor cover ("flipper door") on the left wall of the freezer

stops the ice maker from producing ice if the door is open or

the storage bin is removed.

2. Replace the storage bin on the door and push down to make

sure it is securely in place.

Clean the Ice Storage Bin

Empty the ice container. Use warm water to melt the ice if

necessary.

NOTE: Never use anything sharp to break up the ice in the

bin. This can cause damage to the ice container and the

dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.

REMEMBER

• Allow 24 hours to produce the first batch of ice. Allow 3 days

to completely fill ice container.

• Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

• For Style 1 ice maker, do not force the wire shutoff arm up or

down.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATOR

FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

_mportant information to know about glass shelves

and covers:

Do not ciean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This

reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models)

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the

frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check to make sure that

the shelf is securely in position.

!!ii?iiiiiif> ii!!¸

To raise or lower the shelf:

1. Raise the shelf by pulling forward on the lever located at the

bottom front of the shelf and lift until the shelf locks into the

vertical position.

2. Lower the shelf until it is latched securely in place.

ii i:i?iiiiiii :?!iiiiiiiiii:: / ii ili?¸il:;;:!i!i,!iiiiiiii!ii!:

To raise or lower the shelf:

1. Raise the shelf by first sliding it back and down to make it

half-width. (You can use the shelf in this position to allow

taller items to be stored on the shelf below.)

2. Lift the front of the shelf until it fits securely in place against

the back wall, Lower the shelf securely back into position.

3. Pull the front of the shelf forward until it fits into place.

Crisper and Convertible Vegetable Meat Drawers

To remove and replace drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the

front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of

the way.

2. Replace the crisper or meat drawer by sliding it back in fully

past the drawer stop.

Crisper or Vegetable/Meat Drawer Covers

To remove and replace covers:

1. Remove the crisper and meat drawer. Press up in center of

crisper glass insert until it rises above the plastic frame.

Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame and remove. Repeat steps to remove

the meat drawer cover.

3. Replace back of meat drawer cover frame into supports or

slides on side walls of the refrigerator and lower or slide the

front of the cover frame into place.

4. Slide rear of glass insert into cover frame and lower front into

place. Repeat steps to replace the crisper cover.

The dell drawer stores raisins, nuts, spreads, and other small

items at normal refrigerator temperatures.

To remove and replace the deli drawer:

1. Remove the dell drawer by sliding it straight out to the stop.

Lift the front and slide the drawer out the rest of the way.

Replace the dell drawer b sliding it back past the stop.

The convertible vegetable/meat drawer can be adjusted to

properly chill meats or vegetables. The air inside the pan is

cooled to prevent "spot" freezing and can be set to keep meats

at the National Livestock and Meat Board recommended storage

temperatures of 28°- 32°F (-2°- O°C).

IMPORTANT: To extend freshness, wrap meats in airtight,

moisture-proof materials before storing. Always store meat as

recommended.

Adjusting the Control

The convertible control comes preset at the lowest meat setting.

To change a control setting: Move the control to the right

(colder) or to the left (less cold) as desired.

To store vegetables: Set the control to VEG (all the way to the

left) to store vegetables at their optimal storage temperatures

(which need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the left

(less cold). Remember to wait 24 hours between adjustments.

Doing so gives the temperature of the food time to change.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ................. use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ........................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

Humidity control location:

• Humidity Control on crisper drawer (Style 1 - on left)

• Humidity Control on crisper cover (Style 2 - on right)

High 5 4 3 2 I LOW

:; :s'

To remove and replace the wine rack (left) or can/bottle

rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

NOTE: For long-term storage, place eggs in a covered container

or in their original carton on an interior shelf.

FREEZER FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

To remove and replace the shelf:

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

3. Replace shelf in the reverse order.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot

[907-1,360 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be careful to leave

enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

iiii!! i i ! siiiiiii< ;i:?ii:iiii!! ,iii ili: ii ii %ii iiDoo i :iii!!il

The freezer basket or bin can be used to store bags of frozen

fruits and vegetables that may slide off freezer shelves.

To remove and replace the freezer basket or bin:

1. Remove basket or bin by sliding it out to the stop.

2. Lift the front of the basket or bin and slide it out the rest of the

way.

Replace the basket or bin by positioning it on the side wall

guide rails. Lift the basket or bin front slightly while pushing it

past the guide rail stops and slide basket or bin in the rest of

the way.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and rail assembly onto the tabs above the shelf as shown.

Drep-in Door Rails

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

NOTE: Can racks may be purchased as an Accessory for some

models.

To remove and replace the racks/bins:

1. Remove the racWbin by lifting it and pulling it straight out.

2. Replace the racWbin by sliding it in above the desired

support and pushing it down until it stops.

REFRIGERATOR CARE

E×ptosion Hazard

Use _onf_arnmabls c_ea_sr.

Faiture to do so can result in death, e×plosion,

or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

Cleaning your refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to .95 L] of water).

La page charge ...

KitchenAid KSRA22ILBL00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSRA22ILBL00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KSRA22ILBL00 Owner's manual

KitchenAid KSRA22ILBL00 Le manuel du propriétaire

KitchenAid KSRA22ILBL00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents