KitchenAid KBRS19KTSS01 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBRS19KTSS01

Catégorie: Frigos

Taper: Le manuel du propriétaire

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.kitchenaid.cem for additional information. If you still need assistance, call us at 1-800-422-1230.

In Canada, visit our website at www.kitchenaid.ca or call us at 1-800-807-6777.

You will need your model and serial number located on the right-hand side of the refrigerator interior.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espaffol, o para obtener informaci6n adicional de su

producto, visite: www.kitchenaid.com

Tenga listo su nOmero de modelo completo. Puede encontrar su nOmerode modelo y de serie en la etiqueta ubicada al lado

derecho del interior del refrigerador.

Table of Contents / Table des mati res

REFRIGERATOR SAFETY ................................................................... 1

INSTALLATION INSTRUCTIONS ....................................................... 2

REFRIGERATOR USE ....................................................................... 10

REFRIGERATOR CARE ..................................................................... 14

TROUBLESHOOTING ........................................................................ 15

WATER FILTER CERTIFICATIONS .................................................. 17

PRODUCT DATA SHEETS ................................................................ 18

WARRANTY ........................................................................................ 19

SleCURITle DU RleFRIGleRATEUR ................................................... 20

INSTRUCTIONS D'INSTALLATION ................................................. 21

UTILISATION DU RleFRIGleRATEUR ............................................... 31

ENTRETIEN DU RleFRIGleRATEUR ................................................. 35

DlePANNAGE ...................................................................................... 36

FEUlLLES DE DONNleES SUR LE PRODUIT .................................. 39

GARANTIE .......................................................................................... 40

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

W10137649A

iMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer.

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Properly dispose of packaging.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/211

(1.25 cm) space at the top and behind the refrigerator. If your

refrigerator has an ice maker, allow extra space at the back for the

water line connections. When installing your refrigerator next to a

fixed wall, leave 21/2'' (6.3 cm) minimum on the hinge side (some

models require more) to allow for the door to swing open.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the

refrigerator in alocation where the temperature will fall below 55°F

(13°C).

1/2"(1.26crn)/

21/2" (6.3 crn)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

4 d _ .... ...... '.,

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/411nut driver

• 7/16IIand 1/211Open-end or two • 1/411Drill bit

adjustable wrenches

• Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/16"(4.76 ram) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. Ifyou have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

Ifareverseosmosiswaterfiltrationsystemisconnectedtoyour

coldwatersupply,thewaterpressuretothereverseosmosis

systemneedstobeaminimumof40to60psi(276to414kPa).

Ifthewaterpressuretothereverseosmosissystemislessthan

40to60psi(276to414kPa):

• Checktoseewhetherthesedimentfilterinthereverse

osmosissystemisblocked.Replacethefilterifnecessary.

• Allowthestoragetankonthereverseosmosissystemtorefill

afterheavyusage.

• Ifyourrefrigeratorhasawaterfilter,itmayfurtherreducethe

waterpressurewhenusedinconjunctionwithareverse

osmosissystem.Removethewaterfilter.See"WaterFiltration

System."

Ifyouhavequestionsaboutyourwaterpressure,callalicensed,

qualifiedplumber.

Readalldirectionsbeforeyoubegin.

IMPORTANT:Ifyouturntherefrigeratoronbeforethewaterlineis

connected,turntheicemakerOFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a W' to 1W' (12.7 mm to 3.18 mm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the lower right rear of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use W'

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

Using a cordless drill, drill a W' hole in the cold water pipe you

have selected.

...... A

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

E Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the W' drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so the washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

B-- @

D i

A. Copper tubing D. Compression sleeve

B. "P" clamp E. Water valve inlet port

C. Compression nut

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2ft [61 cm]) with

the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

A. Plastic water tubing C. Compression nut

B, Sleeve D. Copper tubing

Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

A. Plastic water line D. Copper tubing

B. Water valve inlet port E. "P" clamp

C. Compression nut

6. Check connection by pulling on copper tubing. Attach copper

tubing to refrigerator cabinet with a "P" clamp. Turn on water

supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

1. Using a Phillips screwdriver, remove the top door cap. See

Graphic 3.

2. Tap the bottom edge of the refrigerator door handle upward

with a rubber mallet.

3. Handle will slide up approximately 3/4"(19.05 mm) and release

from the door.

Replace Handles (Panel Series)

1. Make sure the bottom door cap is installed. See Graphic 5.

2. Align handle notches with metal mounting tabs on the side of

the door. Slide the handle down until it locks.

3. Tap the top of the handle with a rubber mallet to ensure a snug

fit.

4. Using a Phillips screwdriver, reinstall the top door cap.

Remove Door and Hinges

IMPORTANT:

• Remove food and any adjustable door bins or utility bins from

doors.

• All graphics referenced in the following instructions are

included later in this section after "Final Steps."

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill the ice container.

Graphics are included later in this section.

Remove and ®

Replace Handles (Architect Series)

1. Using a %2"Allen wrench, loosen the two set screws located

on the side of each handle. See Graphics 2 and 4.

2. Pull the handle straight out from the door. Make sure you keep

the screws for reattaching handles.

3. To replace the handle, reverse the directions.

Remove Handles (Panel Series)

IMPORTANT:

• Remove the door from refrigerator before removing handles.

• You must remove the handles to remove the decorator panels

or to reverse the door swing.

_6" Hex-Head Top Hinge Screw

TOOLS NEEDED: %6", %", 1/4"hex-head socket wrench, #2

Phillips screwdriver, and a flat-blade screwdriver.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator door closed until you are ready to lift it

free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

3. Remove the parts for the top hinge as shown in Top Hinge

Graphic. Lift the refrigerator door free from the cabinet.

4. Remove the parts for the bottom hinge as shown in the

Bottom Hinge Graphic.

Reverse Door (Architect ®Series)

IMPORTANT: If you want to reverse your doors so they open

from the opposite side, follow these steps. If you are not reversing

the doors, see "Replace Door and Hinges."

Door Stop Screw

Door Handle Seal Screw Front

Flat-Head Handle Screw Cabinet Hinge Hole Plug

Cabinet

1. Remove the hinge screws from handle side and move them to

opposite side. See Graphic 1-1.

2. Using a flat-blade screwdriver tip wrapped in masking tape,

remove the cabinet hinge hole plugs from the cabinet top and

move them to the opposite side hinge holes as shown in

Graphic 1-2.

Refrigerator door

1. Remove the refrigerator handle assembly including the

mounting posts and screws. Keep all parts together. See

Graphic 2.

2. Remove the door handle seal screw front. Move to opposite

side of refrigerator door as shown in Graphic 5.

3. Removethedoorstopfromthebottomedgeofthe

refrigeratordoor.Movetooppositesideofrefrigeratordooras

showninGraphic3.

4. Attachthedoorhandlemountingpoststotheoppositesideof

thedoor.

5. Positionrefrigeratorhandleovermountingpostsasshownin

Graphic2.Drivetwosetscrewsinthesidesofthehandle.

6. Tightenallscrews.Setasidethedooruntilthehingesand

freezercompartmentdrawerareinplace.

Reverse Door (Panel Series)

IM PORTANT:

• If you want to reverse your door so it opens from the opposite

side, follow these steps. Ifyou are not reversing the door, see

"Replace Door and Hinges."

• You must first remove the handle from the panel series

refrigerator door to reverse the door swing.

1. Using a flat-blade screwdriver tip wrapped in masking tape,

remove the cabinet hinge hole plugs and move them to the

opposite side of the cabinet as shown in Graphic 1.

2. Remove the hinge screws. Move to the opposite side of

cabinet. See Graphic 2.

3. Using a Phillips screwdriver, remove the door stop and door

cap located on the bottom edge of the refrigerator

compartment. See Graphic 5.

4. Using a Phillips screwdriver, remove the top door cap.

5. Remove 1/4"hex-head screws from top door extension.

Reverse the top door extension so the notched corner turns in

toward the interior of the door. See Graphic 3.

6. Remove the side door trim and handle trim by tapping the

bottom edges upward with a soft rubber mallet. The trim will

slide up and release from the door. See Graphic 4.

7. Replace the bottom door cap and install the door stop on

opposite side of the door. See Graphic 5.

8. Using the alternate side door trim, shipped with the

refrigerator, align notches on trim with metal mounting tabs on

side of door. Slide the trim down until it locks into place. Tap

the top of the trim with a rubber mallet to ensure snug fit. See

Graphic 4.

9. Install handle by aligning handle notches with metal mounting

tabs on side of door. Slide the handle down until it locks. Tap

top of handle with rubber mallet to ensure snug fit. See

Graphic 4.

10. Using a Phillips screwdriver, install the top door cap. See

Graphic 3.

Replace Door and Hinges

NOTE: When reversing panel series door, use alternate top hinge

shipped with refrigerator.

1. Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

2. Assemble the parts for the top hinge as shown in the Top

Hinge Graphic. Do not tighten screws completely.

3. Line up the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

Freezer Drawer

IMPORTANT: Two people may be required to remove and replace

the freezer drawer.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

4. Replace the base grille.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in

place. Reinstall top hinge cover. See Top Hinge Graphic.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3 prong outlet.

3. Return all removable door parts to doors and food to

refrigerator.

Architect ®Series

Top Hinge

T A

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5/,c"Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinge

A. Shim (on some models)

B. Center Hinge

C. Hinge Screws

A. Cabinet Hinge Hole Plugs

A. %2" Set Screw

Front View

A. Door Stop Screws

B. Door Stop

A. %2" Set Screw

A. Hinge Screws

Door Handle

Seal Screw

Front

A. Loosen Door Bracket Screws

Panel Series

Bottom Hinge

A. Shim (on some models)

B. Center Hinge

C. Hinge Screws

_-&C-...... p p

i _ B. %" Hex-Head Screws

i C. Top Door Extension

A. Handle Trim

B. Side Door Trim

A. Bottom Door Cap

B. Door Stop

A. Cabinet Hinge Hole Plugs

%0 _ o oo

tl"€?_......................................A

A. Hinge Screws

Depending on your model, your refrigerator may have four

adjustable rollers (Style 1) or a leveler foot screw (Style 2) located

at the base of the refrigerator. If your refrigerator seems unsteady

or you want the door to close more easily, use the instructions

below.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Raise or lower the cabinet.

Style 1 - Front and rear leveling

Using a 3/8"hex driver, turn the roller adjustment screw(s) on each

side to raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the adjustment screws and rollers. This

makes it easier to turn the screws. It may take several turns of the

roller adjustment screw to adjust the tilt of the refrigerator

Turn the brake foot clockwise until it is firmly against the floor to

keep the refigerator from rolling forward when the freezer drawer

is pulled open.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

A. Rear roller adjustment screw

B. Front roller adjustment screw

C. Brake foot

Style 2 - Leveling screw

Using a 1/4"hex driver, turn the leveling screw on each side to raise

or lower that side of the refrigerator.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling screws. This makes it easier to

turn the screws. It may take several turns of the leveling screw to

adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

• To lower, turn the leveling screw counterclockwise.

A. Leveling screw

3. Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

There may be an occasion when you will need to remove the

factory-installed trim kit, such as moving the refrigerator to a new

home or installing custom-made decorator panels. Please read all

instructions before removing the trim kit and decorator panels.

A. 2 _" (6.35 cm) Clearance

B.Raised decoratot panel

C.Raised drawerpanel

Remove the Door Panel

IMPORTANT:

• Door must be removed from refrigerator before removing

handle.

• Top trim must be removed from refrigerator before removing

door panel.

1. Remove the refrigerator handle:

• Using a Phillips screwdriver, remove the top door cap.

• Tap the bottom edge of refrigerator door handle upward

with a rubber mallet.

• The handle will slide up approximately 3/4"(19.05 mm) and

release from door.

2. Remove the door panel:

• Slide out decorator panel and filler board.

• Store panel and filler board in such a manner as to avoid

scratching.

Replace the Door Panel

1. Replace the refrigerator door panel:

• Slowly slide the 1/4"(6.35 mm), maximum thickness,

decorator panel in grooves provided by bottom door cap

and side trim.

• Slide the filler board into place behind the decorator panel,

if necessary.

2. Attach the handle and trim.

3. Reinstall the refrigerator door.

Remove and Replace Freezer Drawer Panel

NOTE: You do not need to remove the freezer drawer to remove

or replace the decorator panel,

1. Pull the freezer drawer out to access the handle screws.

2. Using a Phillips screwdriver, remove the handle screws and lift

off the handle.

3. Slide the decorator panel and filler board up through handle

opening.

4. Replace the decorator panels by reversing directions.

Care of Decorator Panels

1. Clean panels with stainless steel cleaner and polish or mild

soap and water with a clean, soft, damp cloth,

2. Rinse panels thoroughly and blot dry using a dry, soft cloth or

chamois.

NOTE: Do not use paper towels or cleaners which contain

solvents such as ammonia. They can damage the surface of

the panels,

Install Custom Wood Panels

If you plan to install custom wood decorator panels, you will need

to create the panels yourself or consult your cabinetmaker or

carpenter. See dimensional drawings for wood panel inserts,

Flat Panels:

You can create a custom flat panel a maximum of %" (6.35 mm)

thick to replace your decorator panels. Flat wood panels less than

1/4"(6.35 mm) thick are not recommended.

Raised Panels:

A raised panel design can be created by screwing or gluing wood

panels to 1/4"(6.35 mm) backing or by using 3/4"(19.05 mm) stock

with routed edges. Allow 21/2'' (6.35 cm) minimum clearance

between raised edge of panel and handle.

Weight requirements for raised panel inserts:

• Refrigerator door panel should not exceed 30 Ibs (14 kg).

• Freezer drawer panels should not exceed 15 Ibs (7 kg)

combined weight.

Dimensions for Custom Wood Panels

20 cu. ft. Refrigerator door

35%"

(90.5 cm) -_

36V10"

(91.6 cm)

42"

(106.7 cm)

23V4"

(59.1 cm)

Dimensions for Routing Handle Side of Raised Door

Panels (End View)

= |

1/4" (6 ram) max. /

A rain. B

A.Handle

B. Door panel

Dimensions for Routing Door Panel (Side View)

1/4"

(6,35 mm) max.

1/2" I Top

(1.3cm)

rain.

Center face

detail between ,_-"__

offsets

3/8" I

(9.5 turn)

rain. Bottom

-- (6,35 mm) max.

REFRIGERATOR USE

Your model may have Electronic Controls or Digital Controls.

IMPORTANT:

• Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) than recommended setting will not cool the

compartments any faster.

• The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Foryourconvenience,yourrefrigeratorandfreezercontrolsare

presetatthefactory.Whenyoufirstinstallyourrefrigerator,make

surethecontrolsarestillsettotherecommendedsettingas

shown.

Recommended Setting "4"

000 ®0®

co_e FREEZER CO£DER RecommendedSetfiilgs:4 cord REFRIGERATOR COCDER

ColdestSettinys:7

To Turn Your Refrigerator Off/On:

• To turn your refrigerator off, press the freezer down arrow

touch pad until a dash (-) appears in both the refrigerator and

freezer displays. Neither compartment will cool.

Adjusting Electronic Controls

The temperature control range for each compartment is 1 through

7 (coldest).

Press the up or down arrow touch pads to adjust the temperature.

Except when starting the refrigerator, do not adjust either control

more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart below as

a guide.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm Adjust REFRIGERATOR

Control one setting

higher

FREEZER too warm/to little ice Adjust FREEZER

Control one setting

higher

REFRIGERATOR too cold Adjust REFRIGERATOR

Control one setting

lower

FREEZER too cold Adjust FREEZER

Control one setting

lower

For your convenience, your temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended set points as shown.

Recommended Settings

Warmer

Colder G

0°F Recommended 38°F Recommended

FREEZER REFRIGERATOR

_ Warmer

G Colder

IMPORTANT: When the power is on, the temperature display

shows the actual temperature of the compartment.

To Turn Your Refrigerator Off/On:

• Press the freezer (+) touch pad repeatedly until "OFF" appears

in the freezer display. Allow a few seconds for the refrigerator

to shut off. Neither compartment will cool.

• Press either the refrigerator or freezer (-) touch pad to turn on

the refrigerator.

Adjusting Digital Controls

The REFRIGERATOR control adjusts the refrigerator compartment

temperature. The FREEZER control adjusts the freezer

compartment temperature.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The first touch of the (+) or (-) touch pad displays the current

temperature set point. The display will show the set point for

approximately 3 seconds, and then return to the actual

temperature.

• Press the (+) or (-) touch pads until the desired temperature

set point is displayed.

NOTE: Except when first turning on the refrigerator, do not

adjust either temperature control more than one setting at a

time. Wait 24 hours between adjustments for the temperature

to stabilize.

38°F Recommended _ Warmer

Colder

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm Adjust REFRIGERATOR

Control 1° lower

REFRIGERATOR

FREEZER too warm/too little ice Adjust FREEZER

Control 1° lower

REFRIGERATOR too cold Adjust REFRIGERATOR

Control 1° higher

FREEZER too cold Adjust FREEZER

Control 1o higher

Additional Digital Control Center Features

Max Cool

The max cool feature assists with periods of high refrigerator use,

full grocery loads, or temporarily warm room temperatures.

• Press the Max Cool touch pad to set the freezer and

refrigerator to the lowest temperature settings. Press the Max

Cool touch pad again to return to the normal refrigerator set

point.

NOTE: The Max Cool feature will automatically shut off in

approximately 12 hours.

Max Cool

Optimlce _ Feature

The Optimlce ®feature assists with temporary periods of heavy ice

use by increasing ice production.

• Press the Optimlce ®feature touch pad to set the freezer to the

lowest temperature setting. Press the Optimlce ®feature touch

pad again to return to the normal freezer set point.

NOTE: The Optimlce ®feature will automatically shut off in

approximately 24 hours.

Optimlce

Holiday Mode

In Holiday Mode, the freezer will not automatically defrost as often

to conserve energy.

• Press the Holiday Mode touch pad until the indicator light is lit

to turn on this feature. Press the Holiday Mode touch pad

again or open the refrigerator door to turn off this feature.

NOTE: The refrigerator door may be opened within 1 hour of

setting Holiday Mode without turning off the feature.

Holiday Mode

Temp Alarm

The Temp Alarm feature provides temperature information inthe

event of a power outage.

Power outage: During a power outage, if the temperatures in the

refrigerator and freezer compartments exceed normal operating

temperatures, the highest temperature reached will be displayed.

• Press the Temp Alarm touch pad until the indicator light is lit,

to turn on this feature. Press and hold Temp Alarm for

3 seconds until the indicator light goes off to turn off this

feature.

Temperature alarm: An alarm will sound repeatedly if the freezer

or refrigerator compartment temperatures exceed normal

operating temperatures for an hour or more.

The temperature displays will alternately show the current

temperatures and the highest temperatures the compartments

reached.

• Press the Temp Alarm touch pad once to stop the audible

alarm and alternating temperature displays. The Temp Alarm

light will continue to flash until the refrigerator returns to the

set temperature.

Temp

Alarm

Door Alarm

The Door Alarm feature sounds a chime every few seconds when

the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Alarm is

turned off.

Press the Door Alarm touch pad to turn this feature on or off.

The indicator light will be lit when the Door Alarm feature is on.

Door

Alarm

Water Filter Status Light and Filter Reset

(on some models)

See "Water Filtration System"

Digital Control User Preferences

The control center allows you to set user preferences, if desired.

Temperature Display (F_C}

This preference allows you to change the temperature display.

F - Temperature in degrees Fahrenheit

C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms.

ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

Sabbath Mode (SAD)

IMPORTANT: This preference does not disable interior lights.

ON - All control panel lights will be disabled.

OFF - All control panel lights will be enabled.

NOTE: Press any touch pad on the control panel to restore the

control panel lights.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds, The

preference name will appear in the Freezer display and the

preference status (For C) or (ON or OFF) will appear in the

Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the

preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to

change the preference status.

3. Set your preferences by pressing and holding the Door Alarm

touch pad for 3 seconds, or by shutting the refrigerator

compartment door.

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT / LOW (open) for best storage of fruits and vegetables with

skins.

VEGETABLES / HIGH (closed) for best storage of fresh, leafy

vegetables.

Turning the Ice Maker On/Off

Toturn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Dispensing Water

1. Hold a container under the dispenser while pressing the

button.

2. Release the button to stop dispensing.

Ice Production Rate

• The ice maker should produce a complete batch of ice

approximately every 3 hours.

• To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

• Do not store anything on top of the ice maker or in the ice

storage bin.

IMPORTANT:

• After connecting the refrigerator to a water source, flush the

water system. Press the button on the dispenser for

5 seconds, then release it for 5 seconds. Repeat until water

begins to flow. Once water begins to flow, continue

depressing and releasing the dispenser button (5 seconds on,

5 seconds off) for an additional 2 minutes. This will flush air

from the filter and water dispensing system. Additional

flushing may be required in some households. As air is cleared

from the system, water may spurt out of the dispenser.

NOTE: After five minutes of continuous dispensing, the

dispenser will stop dispensing water to avoid flooding. To

continue dispensing, press the dispenser button again.

• Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh

supply.

The water filter is located in the upper right-hand corner of the

refrigerator compartment.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Light

The water filter status light will help you know when to change the

water filter. When the yellow (Order) light is on, it is almost time to

change the water filter. When the red (Replace) light is on, a new

water filter should be installed. See "Water Filtration System."

After replacing the water filter, press and hold FILTER RESET for

3 seconds until the Order or Replace light turns off.

Order Replace

Filter

Reset

Replacing the Water Filter

To purchase a replacement water filter, model 67003523 Part

Number 4396395, contact your dealer or call 1-800-442-9991

U.S.A. or 1-800-807-6777 Canada.

IMPORTANT: Air trapped in the water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the

filter end into the filter head.

3. Turn the filter clockwise until it stops. Snap the filter cover

closed.

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. Ifthis option is chosen,

replace the filter with the blue bypass cap.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner & Polish, Part Number 4396920. To order the

cleaner, call 1-800-442-9991 U.S.A. or 1-800-807-6777

Canada.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size, shape,

and wattage (no greater than 40 watts).

Changing the Refrigerator Light Bulb

1. Unplug the refrigerator or disconnect power.

2. Slide the light shield toward the back of the compartment to

release it from the light assembly.

3. Replace burned-out bulb(s) with appliance bulb(s) no greater

than 40 watts.

4. Replace the light shield by inserting the tabs on the shield into

the liner holes on each side of light assembly. Slide the shield

toward the front until it locks into place.

NOTE: To avoid damaging the light shield, do not force the

shield beyond the locking point.

5. Plug in refrigerator or reconnect power.

Changing the Freezer Light Bulb

1. Unplug refrigerator or disconnect power.

NOTE: You may need to remove the upper freezer shelf or basket

to access the light assembly.

2. The light shield opens from the back. Firmly press forward on

the notches in the back of the shield and pull the shield down.

3. Remove the shield and replace the burned-out bulb with an

appliance bulb no greater than 40 watts.

4. Insert the front tabs of the shield into the liner and snap the

back portion of the shield over the light assembly.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Firsttry the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.kitchenaid.com In Canada, www.kitchenaid.ca

? _. ...... , .....

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker

• Pulsating - fans/compressor adjusting to optimize

performance

• Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle

• Popping - contraction/expansion of inside walls, especially

during initial cool-down

• Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

• Power cord unplugged? Plug into a grounded 3 prong outlet.

• Is outlet working? Plug in a lamp to see if the outlet is

working.

• Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s} opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Freezer door closed completely? Firmly close the freezer

compartment door. If the freezer compartment door will not

close all the way, see "The doors will not close completely."

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

• Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice volume improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice quality improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof

packaging to store food.

• Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

• Water filter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water filtration system

needs additional flushing. Flush the water system before using

a new water filter. Replace water filter when indicated. See

"Water Filtration System."

The water dispenser will not operate properly

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? Straighten the water source

line.

• New installation? Flush and fill the water system. See "Water

Dispenser."

• Is the water pressure at least 35 psi (241 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."

• Water filter installed on the refrigerator? Remove filter and

operate dispenser. If water flow increases, the filter may be

clogged or incorrectly installed, Replace filter or reinstall it

correctly.

• Refrigerator door closed completely? Close the door firmly.

If it does not close completely, see "The doors wUInot close

completely."

• Recently removed the doors? Make sure the water

dispenser wire/tube assembly has been properly reconnected

at the bottom of the refrigerator door. See "Refrigerator

Doors."

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

Water is leaking from the dispenser system

NOTE: One or two drops of water after dispensing is normal,

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

• New installation? Flush the water system. See "Water

Dispenser."

• Recently changed water filter? Flush the water system. See

"Water Dispenser."

• Water on the floor near the base grille? Make sure the water

dispenser tube connections are fully tightened, See

"Refrigerator Doors."

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C),

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

• Recently dispensed large amount of water? Allow 24 hours

for water supply to cool completely,

• Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements,"

WATER FILTER

CERTIFICATIONS

Sta(e of Cahfomia

Departmem of Ilealth Services

WaterTreatmentDevice

CertificateNumber

03- 1583

Date l_sued September 16 2003

[)ate Revised April ?2 ?(KJ4

Trademark/Model DeslQnation Replacement Elements

UKFS001AXX750 UKFS0{ IAXX

469006-750

67003523-750

Manufacturer: P_'_l_Pu_e t_lc

Rated Service Capacity: 750 gaI Rated Service Flow: 078 gpm

Conditions of Certification:

Do not lise w_ere water is mic_obiological/y _msa_ or with water of imknow_ quality, e_cept that systems certified for

cysi rexkictio _ may be used on disinfected waters that may contain fi)terable cysts

PRODUCT DATA SHEETS

Interior Water Filtration System

Model 67003523-750 Capacity 750 Gallons (2839 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42

for the reduction of Chlorine Taste and Odor, Particulate Class I*; and against

NSF/ANSl Standard 53 for the reduction of Lead, Mercury, Atrazine, Toxaphene,

Cysts, Turbidity, Asbestos and Lindane.

This system has been tested according to NSF/ANSl Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 1.88 mg/L 2.0 mg/L _+10% 0.06 mg/L ** 0.05 mg/L 96.84 >97.26

Particulate Class I* 85% reduction 5,700,000 #/mL Atparticles/mLleast10,000 69,000 #/mL 30,583 #/mL 98.94 99.52

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: (-®pH 6.5 0.010 rng/L 0.153 mg/L _ 0.15 mg/L _+10% < 0.001mg/L < 0.001rng/L >99.29% >99.35%

Lead: @pH 8.5 0.010 mg/L 0.150 mg/L t 0.15 mg/L _+10% < 0.001mg/L < 0.001mg/L >99.29% >99.33%

Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 90.91 95.70

Mercury: @ pH 8.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0015 mg/L 0.0008 mg/L 75.93 86.22

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 _+10% < 0.001mg/L < 0.001mg/L 91.67% 92.97%

Atrazine 0.003 mg/L 0.009mg/L 0.009 mg/L _+10% < 0.002 mg/L < 0.002 mg/L 75.31% 76.99%

Asbestos 99% 155 MF/L 107to 108fibers/L tt < 1 MF/L < 1 MF/L >99.99% >99.99%

Live Cysts _ >99.95% 166,500 #/L 50,000/L min. < 1 #/L_ < 1 #/L_ >99.99 >99.99

Turbidity 0.5 NTU 10.7 NTU 11 _+1 NTU 0.49 NTU 0.31 NTU 95.2 97.09

Lindane 0.0002 mg/L 0.002 mg/L 0.002 _+10% < 0.0001mg/L 0.000 mg/L 96.50% 98.72%

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.78 gpm (1.9 Lpm). Pressure

71.6°F (20°C to 22°C).

• It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

• The filter monitor system measures the amount of water that

passes through the filter and alerts you to replace the filter.

When 90% of the filter's rated life is used, the yellow (Order)

light comes on. When 100% of the filter's rated life is used, the

red (Replace) light comes on, and it is recommended that you

replace the filter. Use replacement filter model 67003523;

order Part Number 4396395. 2007 suggested retail price of

$49.99 U.S.A./S65.95 Canada. Prices are subject to change

without notice.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• Refer to the "Water Filtration System" section for the

Manufacturer's name and telephone number.

= 60 psig (413.7 kPa). Temp. = 68°F to

• Refer to the "Warranty" section for the Manufacturer's limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 35 - 120 psi (241 - 827 kPa)

Water Temperature 33 ° - 100°F (1° - 38°C)

Service Flow Rate 0.78 gpm (2.9 L/min.) @ 60 psi.

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tThese contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

t+Fibers greater than 10 um in length

_Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

KITCHENAID ®REFRIGERATOR WARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished

with the product, KitchenAid or KitchenAid Canada (hereafter "KitchenAid") will pay for factory specified parts and repair labor to correct defects

in materials or workmanship. Service must be provided by a KitchenAid designated service company.

On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated and

maintained according to instructions attached to or furnished with the product, KitchenAid will pay for replacement parts to correct defects in

materials and workmanship.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEM PARTS

In the second through fifth years from the date of purchase, when this major appliance is operated and maintained according to instructions

attached to or furnished with the product, KitchenAid will pay for replacement or repair of the refrigerator/freezer cavity liner (including labor

costs) if the part cracks due to defective materials or workmanship. Also, in the second through fifth years from the date of purchase, KitchenAid

will pay for factory specified parts and labor to correct defects in materials or workmanship in the sealed refrigeration system. These parts are:

compressor, evaporator, condenser, dryer, and connecting tubing. Service must be provided by a KitchenAid designated service company.

SIXTH THROUGH TENTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM PARTS

In the sixth through tenth years from date of purchase, when this major appliance is operated and maintained according to instructions attached

to or furnished with the product, KitchenAid will pay for factory specified parts to correct defects in materials or workmanship in the sealed

refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and connecting tubing.

ITEMS KITCHENAID WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair house

fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with

electrical or plumbing codes, or use of products not approved by KitchenAid.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published

installation instructions.

11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was purchased.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO

ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS

OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if another

warranty applies. 5/07

For additional product information, in the U.S.A., visit www.kitchenaid.com

In Canada, visit www.kitchenaid.ca

If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may

contact KitchenAid at the number below.

Have your complete model number ready. You can find your model number and serial number on the label located on the right-hand

side of the refrigerator interior.

For assistance or service in the U.S.A., call 1-800-422-1230. In Canada, call 1-800-807-6777.

If you need further assistance, you can write to KitchenAid with any questions or concerns at the address below:

In the U.S.A.: In Canada:

KitchenAid Brand Home Appliances KitchenAid Brand Home Appliances

Customer eXperience Center Customer Interaction Centre

553 Benson Road 1901 Minnesota Court

Benton Harbor, MI 49022-2692 Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

Please keep this User Instructions and model number information for future reference.

Nous vous REMERCIONS d'avoir achet6 ce produit de haute qualit& Si vous rencontrez un probl_me non mentionn6 dans la

section DI2PANNAGE,veuillez visiter notre site www.kitchenaid.com pour des informations suppl6mentaires. Si vous avez toujours

besoin d 'assistance, veuillez nous t616phonerau 1-800-422-1230. Au Canada, visitez notre site www.kitchenaid.ca ou t616phonez-

nous au 1-800-807-6777.

Vous aurez besoin de vos num@os de module et de s6rie situ6s sur le c6t6 droit _.I'int@ieur du r6frig@ateur.

P P P P

SECURITE DU REFRIGERATEUR

Votre s_curit_ et celle des autres est tres importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tousles messages de securite et de vous y conformer.

Voici le symbole d'alerte de securit&

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves &vous

eta d'autres.

Tous les messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de deces ou de blessure grave si vous ne

suivez pas immediatement lee instructions.

Risque possible de deces ou de blessure grave si vous

ne euivez pas lee instructions.

Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

JMPORTANTES INSTRUCTIONS DE SI_CURITE

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou des blessures Iors de I'utilisation du

refrigerateur, prendre quelques precautions fondamentales, y compris les suivantes :

[] Brancher I'appareil sur une prise & 3 alveoles reliee & la

terre.

[] Ne pas enlever la broche de liaison & la terre.

[] Ne pas utiliser un adaptateur.

[] Ne pas utiliser un c&ble de rallonge.

[] Utiliser deux ou plus de personnes pour deplacer et installer

le refrigerateur.

[] Debrancher la source de courant electrique avant I'entretien.

[] Replacer pieces et panneaux avant de faire la remise en

marche.

[] Utiliser un produit de nettoyage ininflammable.

[] Garder les mat@iaux et les vapeurs inflammables, telle que

I'essence, loin du refrigerateur.

[] Debrancher le refrigerateur avant I'installation de la

machine & glagons (seulement pour modeles pr_ts &

recevoir une machine b,gla£ons).

[] Enlever les portes de votre vieux refrigerateur.

CONSERVEZ CES INSTRUCTIONS

La page charge ...

KitchenAid KBRS19KTSS01 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBRS19KTSS01

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KBRS19KTSS01 Owner's manual

KitchenAid KBRS19KTSS01 Le manuel du propriétaire

KitchenAid KBRS19KTSS01 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents