KitchenAid KSRS22FGBT04 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSRS22FGBT04

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

KitchenAid _

SIDE BYSIDE REFRIGERATOR

For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230

in Canada, call for assistance 1-800-461-5681, for instaflation and service, ca& 1-800-807-6777 or visit our website at...

www.kitchenaid,comor www.kitchenaid.com/canada

REFRIGERATEUR COTE A COTE

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777 ou visitez notre site web &

www.kitchenaid.com/canada

Table of Contents/Table des matieres .................... 2

2206106

TABLE OF CONTENTS

REFRIGERATOR SAFETY ..........................................................3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLING YOUR REFRIGERATOR .......................................... 4

Unpacking Your Refrigerator ....................................................... 4

Space Requirements .................................................................... 4

Electrical Requirements ............................................................... 5

Removing the Doors .................................................................... 5

Connecting the Refrigerator to aWater Source .......................... 6

Interior Water Filter Installation .................................................... 7

Water System Preparation ........................................................... 8

Factory Trim Kit ............................................................................ 8

Base Grille .................................................................................... 9

Door Closing ............................................................................... 10

Understanding Sounds You May Hear ...................................... 10

USING YOUR REFRIGERATOR .................................................. 10

Ensuring Proper Air Circulation .................................................. 10

Setting the Controls ................................................................... 11

Adjusting Control Settings ......................................................... 11

REFRIGERATOR FEATURES ...................................................... 12

Water and ice Dispensers .......................................................... 12

Base Grille Water Filtration and Monitoring System ................. 13

Interior Water Filtration System ................................................. 14

Refrigerator Shelves ................................................................... 14

Lateral Adjustable Shelf ............................................................. 14

Flip-up Shelf ............................................................................... 15

Adjustable Flip-up Shelf ............................................................. 15

Dell Drawer ................................................................................. 15

Convertible Vegetable/Meat Drawer, Crisper and Covers ........ 15

Convertible Vegetable/Meat Drawer Temperature Control ....... 16

Crisper Humidity Control ........................................................... 16

Utility or Egg Bin......................................................................... 16

Wine or Can/Bottle Rack ........................................................... 16

FREEZER FEATURES .................................................................. 17

Ice Make[ and Storage Bin ........................................................ 17

Freezer Shelf .............................................................................. 18

Freezer Basket ........................................................................... 18

DOOR FEATURES ........................................................................ 18

Door Rails ................................................................................... 18

Door Bins .................................................................................... 19

Can Rack .................................................................................... 19

CARING FOR YOUR REFRIGERATOR ....................................... 19

Cleaning Your Refrigerator ......................................................... 19

Changing the Light Bulbs ........................................................... 19

Power Interruptions .................................................................... 20

Vacation and Moving Care ......................................................... 20

TROUBLESHOOTING .................................................................. 21

ASSISTANCE OR SERVICE ......................................................... 24

Accessories ................................................................................ 24

KITCHENAID® REFRIGERATOR WARRANTY ....................... 25

WATER FILTER CERTIFICATES .............................................. 26

PRODUCT DATA SHEETS ....................................................... 28

TABLE DES MATIFRES

SItCURITE DU RItFRIGItRATEUR ........................................... 31

Mise au rebut de votre vieux refrigerateur ................................. 31

INSTALLATION DU REFRIGERATEUR ...................................... 32

Deballage de votre refrigerateur ................................................ 32

Espacement requis ..................................................................... 32

Specifications electriques .......................................................... 33

Enlevement des portes ............................................................... 33

Raccordement du rdrigerateur a une canalisation d'eau .........34

Systeme interieur de filtration d'eau .......................................... 35

Preparation du systeme d'eau ................................................... 36

Ensembles decoratifs de I'usine ................................................ 36

Grille de la base .......................................................................... 38

Fermeture des portes ................................................................. 38

Les bruits de I'appareil que vous pouvez entendre ................... 38

UTILISATION DU REFRIGERATEUR .......................................... 39

Pour s'assurer d'une circulation d'air appropriee ...................... 39

Reglage des commandes .......................................................... 39

Ajustement des reglages de controle ........................................ 40

CARACTERISTIQUES DU REFRIGERATEUR ........................... 40

Distributeurs d'eau et de glaqons .............................................. 40

Systeme de filtration et de controle

d'eau a la grille de la base .......................................................... 42

Systeme de filtration d'eau interieur .......................................... 43

Tablettes du refrigerateur ........................................................... 43

Tablette reglable laterale ............................................................ 43

Tablette relevable ....................................................................... 44

Tablette relevable ajustable ....................................................... 44

Tiroir pour specialites alimentaires ............................................ 44

Tiroir a legumes/viande convertible, bac a legumes

et couvercles .............................................................................. 44

Reglage de la temperature du tiroir

legumes/viande convertible ....................................................... 45

Reglage de I'humidite dans le bac a legumes ........................... 45

Casier utilitaire ou oeufrier .......................................................... 46

Casier a vin ou porte-cannettes/bouteilles ................................ 46

CARACTERISTIQUES DU CONGI_LATEUR ............................... 46

Machine a glacons et bac d'entreposage ................................. 46

Tablette de congelateur ............................................................. 48

Partier de congelateur ................................................................ 48

CARACTE_RISTIQUES DE LA PORTE ......................................... 48

Tringles dans la porte ................................................................. 48

BaIconnets .................................................................................. 48

Porte-cannettes .......................................................................... 49

ENTRETIEN DE VOTRE RE_FRIGIeRATEUR ............................... 49

Nettoyage du refrigerateur ......................................................... 49

Remplacement des ampoules d'eclairage ................................ 49

Pannes de courant ..................................................................... 50

Entretien avant les vacances ou Iors d'un demenagement .......51

DI_PANNAGE ................................................................................. 51

ASSISTANCE OU SERVICE ......................................................... 55

Aux Etats-Unis ............................................................................ 55

GARANTIE DU RE_FRIGE_RATEURKITCHENAID® ................. 56

FEUILLES DE DONNE_ES SUR LE PRODUIT .......................... 57

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANTSAFETYINSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker (on

ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water

(on some models).

SAVETHESEINSTRUCTIONS

Proper Disposal of

Your Old Refiigerator

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for ':just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

INSTALLING YOUR

REFRIGERATOR

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

• Remove tape and any labels from your refrigerator before

using (except the model and serial number label).

To remove any remaining tape or glue, rub the area briskly

with your thumb. Tape or glue residue can also be easily

removed by rubbing a small amount of liquid dish soap over

the adhesive with your fingers. Wipe with warm water and

dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the "Refrigerator Safety" section.

IMPORTANT: Do not remove any permanent instruction labels

inside your refrigerator, or the Tech Sheet that is fastened to the

base grille.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the "Caring for Your Refrigerator" section.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion,

or fire.

To ensure proper ventilation for your refrigerator, allow for

.5 in. (1.25 cm) space on each side and at the top.

.5" (1.25 cm)

II -- Iii

2"(5.08cm)

If your refrigerator has an ice maker, make sure you leave

some extra space at the back for the water line connections.

The refrigerator can be flush against the back wall if you do

not have an ice maker installed.

• If you are installing your refrigerator next to a fixed wall, leave

2 in. (5.08 cm) minimum on each side (depending on your

model) to allow for the door to swing open.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection:

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension

cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control, (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or

electrical shock.

NOTE: Before removing doors, open both doors and remove

base grille (see the "Base Grille" section).

Tools Needed:

1Ain. hex-head socket wrench and 5/16in. hex-head socket

wrench.

1. Unplug refrigerator or disconnect power.

2. If you have a dispenser (ice or water), disconnect water line

(behind base grille).

• Remove hose from clip.

• Disconnect union nut and slide it back onto tube.

• Remove metal insert from tube.

• Remove union nut and spring.

Style 1

Remove left top hinge.

• Remove hinge cover and screws. DO NOT REMOVE

SCREW 1 AS SHOWN IN DIAGRAM.

• Disconnect wiring plug and both ground wires.

Carefully lift door up off bottom hinge. Make sure you

protect water line from damage.

Style2 6. Replacedoors.

Disassemble right top hinge,

• Remove hinge cover and screws, DO NOT REMOVE

SCREW 1 AS SHOWN IN DIAGRAM.

• Lift door up off bottom hinge.

Style 1

Style 2

III I 1

Remove bottom hinge, if necessary. Both bottom hinges have

similar construction. DO NOT REMOVE SCREW 1 AS

SHOWN IN DIAGRAM.

NOTE: It may not be necessary to remove the bottom hinge

to move refrigerator through a doorway.

Electrical Shock Hazard

Reconnect both ground wires.

Failure to do so can result in death or

electrical shock.

7. Reconnect both ground wires.

8. Reconnect wiring plug.

9. Replace hinge cover and screws.

10. Plug in refrigerator or reconnect power.

Read all directions carefully before you begin.

IMPORTANT:

• If operating the refrigerator before installing the water

connection, turn ice maker to the OFF position to prevent

operation without water.

• All installations must be in accordance with local plumbing

code requirements.

• Use copper tubing and check for leaks.

• Install copper tubing only in areas where temperatures will

remain above freezing.

• It may take up to 24 hours for your ice maker to begin

producing ice.

Tools required:

• Standard screwdriver

• 7A6in. and 1/2in. open-end wrenches or two adjustable

wrenches

• ¼in. nut driver

• ¼in. drill bit

• Hand drill or electric drill (properly grounded)

NOTE: Your refrigerator dealer has a kit available with a

¼ in. (6.35 mm) saddle-type shut-off valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a piercing-

type or 3A6in. (4.76 mm) saddle valve which reduces water flow

and clogs more easily.

Cold water supply

The ice maker water valve contains a flow washer which is used

as a water pressure regulator. The ice maker needs to be

connected to a cold water line with water pressure between 30

and 120 psi. If a problem occurs, call your utility company.

Connecting to water line:

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. LocateaV2in. to 11/4in. (12.7 mm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. To determine the length of copper tubing you will need,

measure from connection on lower left rear of refrigerator to

water pipe. Add 7 ft. (2.1 m) to allow for moving refrigerator

for cleaning. Use 1/4in. (6.35 ram) O.D. (outside diameter)

copper tubing. Be sure both ends of copper tubing are cut

square.

5. Using a grounded drill, drill a 1/4in. hole in the cold water pipe

you have selected.

........... 2

" ............ 3

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Oft Valve

7. Packing Nut

6. Fasten shut-off valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the 1/4in. drilled hole in the water

pipe and that washer is under the pipe clamp. Tighten

packing nut. Tighten the pipe clamp screws carefully and

evenly so washer makes a watertight seal. Do not overtighten

or you may crush the copper tubing, especially if soft (coiled)

copper tubing is used. Now you are ready to connect the

copper tubing.

7. Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and

turn ON main water supply and flush out tubing until water is

clear. Turn OFF shut-off valve on the water pipe. Coil copper

tubing.

Connecting to refrigerator:

11 Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten. Use the tube clamp on the back of the

refrigerator to secure the tubing to the refrigerator as shown.

This will help prevent damage to the tubing when the

refrigerator is pushed back against the wall. Move to step 2.

Turn shut-off valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

'_ 1

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

4. Valve Inlet

3. The ice maker water valve is equipped with a built-in water

strainer. If local water conditions require periodic cleaning or

a well is your source of water supply, a second water strainer

should be installed in the 1/4in. (6.35 ram) water line. Obtain a

water strainer from your nearest appliance dealer. Install at

either tube connection.

4. Plug in refrigerator or reconnect power.

The interior water filter cartridge is located in the upper right-

hand corner of the fresh food compartment of the refrigerator.

The interior water filter cartridge should be replaced every six

months or earlier if the flow of water to your water dispenser or

ice maker decreases noticeably. (See "Replacing the interior

water filter cartridge" in the features section of this book.)

Installing the interior water filter cartridge

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

1. Carefully remove the interior water filter cartridge from its

packaging. Remove the red cap from the cartridge.

2. Apply the appropriate month sticker to the cartridge as a

reminder to replace the cartridge within six months. Then

apply the "Water Filter Replacement Reminder" sticker to

your calendar as a reminder to replace the cartridge in six

months.

Line up the INSTALL mark on the water filter label with the

indicator line that is molded into the filter mounting bracket

cover. Push the cartridge into the filter mounting bracket.

Twist the cartridge 1/4turn to the right to lock it into place. The

REMOVE mark should be lined-up with the indicator line

located on the front cover.

41RUNWATERTHROUGHTHEDISPENSERUNTILTHE

WATERRUNSCLEAR(about2-3gallonsor6-7minutes).

Thiswillcleanthesystemandclearairfromthelines.

Additionalflushingmayberequiredinsomehouseholds.

NOTE:Asairisclearedfromthesystem,watermayspurtout

ofthedispenser.

5. Opentherefrigeratordoorandinspectthefiltersystemfor

waterleaks.Ifyouseewaterleaks,seethe"Troubleshooting"

section.

NOTE:Youcanrunthedispenserwithoutawaterfiltercartridge.

Yourwaterwillnotbefiltered.

Pleaseread before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. For Style 1

lift up the wire shut-off arm as shown. For Style 2 move the

switch to the OFF (right) setting as shown.

Style 1

Style 2

Flush the water system by dispensing and discarding

2 to 3 gallons (approximately 6 to 7 minutes) of water through

the dispenser. This will clean the system and help clear air

from the lines. Additional flushing may be required in some

households.

Open the freezer door and turn on the ice maker. For Style 1

lower the wire shut-off arm. For Style 2 move the switch to

the ON (left) position. Please refer to the "Ice Maker and

Storage Bin" features section for further instructions on the

operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice. To

do so, set the switch on the front of the ice maker to MAX.

There may be an occasion when you will need to remove the

factory-installed trim kit, such as moving the refrigerator to a new

home or installing custom-made decorator panels. Please read

all instructions carefully before removing the trim kit and

decorator panels.

1 2

Freezer Door Refrigerator Door

1.Decorator Panel5

2. Filler Panel5

3. Handles

Removing the Door Panels

NOTE: When removing and replacing decorator panels, only the

handle is removed. All other trim pieces remain attached to the

doors.

1. Remove the refrigerator and freezer handles:

• Using a Phillips screwdriver, remove the screws that

hold each handle in place.

• Lift off handle. Make sure you keep screws for reattaching

handles.

2. Remove the door panels:

• Open refrigerator or freezer door.

• Slide out decorator panel and filler board.

• Repeat process for other panels and filler boards.

• Store panel and filler boards carefully to prevent

scratching.

Replacing the Door Panels

1. Replace the refrigerator or freezer door panels:

• Open refrigerator or freezer door.

• Carefully slide the V8in. decorator panel into place behind

the side trim.

• Push the filler board into place behind the decorator

panel.

• Repeat process for other panels and filler boards.

2. Attach the handles:

NOTE: Freezer door handle is notched to fit around the dispenser

panel.

• Align the top of the refrigerator or freezer handle flush

with the top trim. Fasten the handle to the refrigerator or

freezer door with the screws, using a Phillips screwdriver.

• Repeat the process for the other handle.

Careof Decorator Panels

1. Glean panels with an anti-static cleaner (available in

electronics or computer departments) or mild soap and water

with a clean, soft, damp cloth.

2. Rinse panels thoroughly and blot dry using a dry, soft cloth or

chamois.

3. DO NOT use paper towels or cleaners which contain solvents

such as ammonia. They can damage the surface of the

panels.

4. If small scratches should appear on the panels, they may be

filled using an automotive paste wax (NOT a cleaner/wax

combination). Apply wax sparingly and buff lightly with a

clean, soft cloth using a circular motion.

Installing Custom Wood Panels

If you plan to install custom wood decorator panels, you will need

to create the panels yourself or consult your cabinet maker or

carpenter. See dimensional drawings for wood panel inserts.

Flat panels:

You can create a custom flat panel 1/4in. (6.35 mm) thick to

replace your decorator panels. Flat wood panels less than 1/4in.

(6.35 ram) thick are not recommended.

Raised panels:

A raised panel design can be created by screwing or gluing wood

panels to 1/4in. (6.35 mm) backing or by using 3/4in. (19.05 mm)

stock with routed edges.

Weight requirements for raised panel inserts:

• Refrigerator door panel should not exceed

25 Ibs (9.98 kg).

• Freezer door panels should not exceed 18 Ibs (6.80 kg)

combined weight.

Dimensions for Custom Wood Panels:

22 cu. ft. Freezer and Refrigerator door

25 & 27 cu. ft. Freezer and Refrigerator door

(6.35ram)

63318 ''

_1415116"

c''_m} ' (160.97 cm)

(37.94

.... q,,,,

i 28112.

(793 turn)

(635 ram)

3/4"rain. 31/4"

(19 05mmmin ) (8255 mmmin ) 3/4"

.... d9 05rnm_

TOPWEW f _

1/4"

(635ram)

1/4"

(635 mm)

m "-< _ 5/1_'

(7¸93ram)

_ _ 9tl116,, ------_

(50.01 cm)

6.3_ ram)

31/4" 314"min 3/4"

825_mmrain 1905mmmin - -o

.... !lU u_ mm,

1/4"

(635 mm)

To remove the base grille:

1. Open both refrigerator doors.

2. Place hands along the ends of the grille, with your thumbs

along the top. Push in with your thumbs and pull up on the

bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille

after cleaning.

To replace the base grille:

1. Open the doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

Yourrefrigeratorhastwofrontadjustablerollers-- oneonthe

rightandoneontheleft,Ifyourrefrigeratorseemsunsteadyorif

youwantthedoorstoclosemoreeasily,adjusttherefrigerator's

tiltusingtheinstructionsbelow:

1. Plugintoagrounded3prongoutlet,

2. Movetherefrigeratorintoitsfinalposition,

3. Removethebasegrille(see"BaseGrille"earlierinthis

section),Thetwolevelingscrewsarepartofthefrontroller

assemblieswhichareatthebaseoftherefrigeratoroneither

side,

4. Useascrewdrivertoadjustthelevelingscrews,Turnthe

levelingscrewtotherighttoraisethatsideoftherefrigerator

orturnthelevelingscrewtothelefttolowerthatside,Itmay

takeseveralturnsofthelevelingscrewstoadjustthetiltof

therefrigerator,

NOTE:Havingsomeonepushagainstthetopofthe

refrigeratortakessomeweightoffthelevelingscrewsand

rollers,Thismakesiteasiertoadjustthescrews,

• Yourrefrigeratorisdesignedtorunmoreefficientlytokeep

yourfooditemsatthedesiredtemperature.Thehigh

efficiencycompressormaycauseyournewrefrigeratortorun

longerthanyouroldone,andyoumayhearapulsatingor

high-pitchedsound.

• Waterdrippingonthedefrostheaterduringadefrostcycle

maycauseasizzlingsound.

• Youmayheartheevaporatorfanmotorcirculatingtheair

throughtherefrigeratorandfreezercompartments.

• Aseachcycleends,youmayhearagurglingsounddueto

therefrigerantflowinginyourrefrigerator.

• Contractionandexpansionoftheinsidewallsmaycausea

poppingnoise.

• Youmayhearairbeingforcedoverthecondenserbythe

condenserfan.

Youmayhearwaterrunningintothedrainpanduringthe

defrostcycle.

USING YOUR

REFRIGERATOR

In order to ensure proper temperatures, you need to permit air to

flow between the two sections. Cold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator

section through the top vent. Air then returns to the freezer as

shown.

5. Open both doors again and check to make sure that they

close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It

may take several more turns, and you should turn both

leveling screws the same amount.

6. Replace the base grille.

%, ....

................................................................

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, like the floor, walls, and cabinets, can make the sounds

seem louder than they actually are. The following describes the

kinds of sounds and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

• The defrost timer will click when the automatic defrost cycle

begins and ends. Also, the Thermostat Control (or

Refrigerator Control depending on the model) will click when

cycling on and off.

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

Do not block any of these vents with food such as soda, cereal,

bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer from food, wrap or cover foods tightly.

_b_:__ ___1_CA:_:I_O,_,S

For your convenience, your refrigerator controls are preset at

the factory. When you first install your refrigerator, make sure

that the controls are still preset. The Refrigerator Control and the

Freezer Control should both be at the "mid-settings" as shown in

the illustrations below.

For both Style 1 and Style 2, The Refrigerator Control adjusts

the refrigerator compartment temperature. Settings to the left

of the mid-setting make the temperature less cold. Settings to

the right of the mid-setting make the temperature colder.

For both Style 1 and Style 2, The Freezer Control adjusts the

freezer compartment temperature. Settings to the left of the

mid-setting make the temperature less cold. Settings to the right

of the mid-setting make the temperature colder.

NOTE: For Style 1, your product will not cool when the

Refrigerator Control is set to OFE For Style 2, your product will

not cool when the Freezer Control is set to OFE

Style 1

Freezer Refrigerator

cold 1 2 A 3 4 colder off 1 2 A 3 4 colder

Style 2

Freezer Refrigerator

Off 1 2 • 3 4 Colder Cold 1 2 • 3 4 Colder

Give your refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put food into

the refrigerator.

IMPORTANT: If you add food before the refrigerator has cooled

completely, your food may spoil. Adjusting the Refrigerator and

Freezer Controls to a higher (colder) than recommended

setting will not cool the compartments any faster.

NOTE: The Automatic Exterior Moisture control continuously

guards against moisture buildup on the outside of your

refrigerator cabinet. This control does not have to be set or

adjusted.

REFRIGERATOR section

too warm

• Door opened often

• Large amount of food added

• Room temperature very warm

Give the refrigerator time to cool down completely before adding

food. It is best to wait 24 hours before you put food into the

refrigerator. The settings indicated in the previous section should

be correct for normal household refrigerator usage. The controls

are set correctly when milk or juice is as cold as you like and

when ice cream is firm.

If you need to adjust temperatures in the refrigerator or freezer,

use the settings listed in the chart below as a guide. Wait at least

24 hours between adjustments.

RECOMMENDED

CONDITION/REASON: ADJ USTMENT:

Adjust

REFRIGERATOR

Control one setting

higher

For Style 1 controls

only: after adjusting

control, wait 24

hours and then

check the FREEZER

temperature

• Air vent blocked byitems

Move packages out

of airstream

FREEZER section too warm/ice

not made fast enough

• Door opened often

• Large amount of food added

• Very cold room temperature

(can't cycle often enough)

• Heavy ice usage

Adjust FREEZER

Control one setting

higher

REFRIGERATOR section

too cold

• Controls not set correctly for your

conditions

Adjust

REFRIGERATOR

Control one setting

lower

For Style 1 controls

only: after adjusting

control, wait 24

hours and then

check the FREEZER

temperature

FREEZER section too cold Adjust FREEZER

• Controls not set correctly for your Control one setting

conditions lower

REFRIGERATOR

FEATURES

To dispense ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed

ice, a special light that turns on when you use the dispenser, or a

lock option to avoid accidental dispensing,

The ice dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the

ice bin.

• Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes

and the ice dispensing stops. The dispensing system will not

operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before

dispensing ice, select which type of ice you prefer. The button

controls are designed for easy use and cleaning.

• For cubed ice, press the CUBE button until the red indicator

appears in the window above the CUBE button.

ICE

CRUSH CUBE

• For crushed ice, press the CRUSH button until the red

indicator appears in the window above the CRUSH button.

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from CRUSH to CUBE, a few ounces of crushed

ice will be dispensed along with the first cubes.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The water dispenser

When the refrigerator is first hooked up, press the water

dispenser bar with a glass orjar until you draw and discard 2 to 3

quarts (1.9 to 2.8 L). It will take three to four minutes for the water

to begin dispensing. The water you draw and discard rinses the

pipes. Allow several hours for the refrigerator to cool down and

chill water.

IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray.

The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned.

To dispense water:

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

NOTE: Dispense enough water every week to maintain a fresh

supply

The dispenser light

The dispenser area has a light. It can be turned on manually by

pressing the ON button at the right hand side of the control

panel. The red indicator above the ON button will appear. On

some models: Whenever you use the dispenser the lever will

automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for

information on changing the dispenser light bulb.

On models without crushed ice, the light switch is a rocker-style

type. Push the switch to turn the light on, and push again to turn

the light off.

The dispenser lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent

accidental dispensing by small children and pets. Toturn off the

dispenser, press the LOCK button. The indicator will appear

above the LOCK button and the ice and water dispensers will not

work. To unlock the dispenser, press the UNLOCK button until

the indicator appears. Then continue to dispense ice or water as

usual.

DISPENSER

LOCK UNLOCK

NOTE: The lock feature does not shut off power to the product,

to the ice maker, or to the dispenser light. It simply deactivates

the dispenser levers.

¢, Z '" y '

The base grille water filter status light

The water filter status light will help you know when to change

your water filter cartridge. The light is located at the top of the

refrigerator compartment. The light will change from green to

yellow. This tells you that it is almost time to change the water

filter cartridge (90% of the filter life has been used). It is

recommended that you replace the base grille water filter

cartridge when the water filter indicator light changes to red OR

water flow to your water dispenser or ice maker decreases

noticeably. (See "Changing a base grille water filter cartridge"

later in this section.)

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

7. Status Light

2. Light Switch

After changing the water filter cartridge, reset the water filter

status light by pressing the light switch 5 times within 10

seconds. The status light will change from red to green when the

system is reset.

Non-indicator water filter (on some models)

If your refrigerator does not have the water filter status light, you

should change the water filter cartridge every 6-9 months

depending upon your usage. If the water flow to the water

dispenser or icemaker decreases noticeably before 6 months

have passed, replace the water filter cartridge more often. (See

"Changing a base water filter cartridge" later in this section.)

Changing a base grille water filter cartridge

The base grille water filter is located below the freezer

compartment door.

1. Locate the water filter cartridge cap in the front base grille

below the freezer compartment door. Rotate the cap

counterclockwise to a vertical position and pull the cap and

filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur.

2. Remove the cartridge cap by sliding it off the end of the old

cartridge. The cap will slide to the left or right. DO NOT

DISCARD THE CAR

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

4. Slide the cartridge cap onto the new cartridge as shown

above in Step 2.

5. With cartridge cap in the vertical position, push the new filter

cartridge into the base grille until it stops. Rotate the cartridge

cap clockwise to a horizontal position.

6. RUN WATER THROUGH THE DISPENSER UNTIL THE

WATER RUNS CLEAR (about 2 - 3 gallons or 6 - 7 minutes).

This will clean the system and clear air from the lines.

Additional flushing may be required in some households.

NOTE: As air is cleared Fromthe system, water may spurt out

of the dispenser.

Using the dispenser without the water filter

You can run the dispenser without a water filter cartridge. Your

water will not be filtered. Ifyou run the dispenser without a water

filter cartridge, keep the cartridge cap and replace it in the base

grille for future use.

1. Remove the base grille water filter cartridge (See "Changing a

base grille water filter cartridge" earlier in this section.) Then

slide the cartridge cap off the end of the filter cartridge. DO

NOT DISCARD THE CAP

2. With the cartridge cap in the vertical position, insert the cap

into the base grille until it stops.

Rotate the cartridge cap to a horizontal position as shown in

step 5.

NOTE: The cartridge cap may not be even with the base

grille.

The interior water filter cartridge is located in the upper right-

hand corner of the fresh food compartment of the refrigerator.

The interior water filter cartridge should be replaced every six

months or earlier if the flow of water to your water dispenser or

ice maker decreases noticeably

Replacing the interior water filter cartridge

1. Twist the interior water filter cartridge 1/4turn to the left. The

INSTALL mark will be lined up with the indicator mark located

on the filter mounting bracket cover.

2. Gently pull down on the cartridge to remove it from the filter

mounting bracket assembly. To prevent water from spilling

inside the refrigerator, DO NOT TIP the cartridge.

3. Dispose of the cartridge.

4. To install a new cartridge, refer to "Installing the interior water

filter cartridge" section in this Use and Care guide.

NOTE: You can run the dispenser without a water filter cartridge,

Your water will not be filtered.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

11 Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports.

3. Lower the front of the shelf and check to make sure that the

shelf is securely in position.

S: :tj

¢:: V

To slide the shelf from side to side:

11 Lift up on the front of shelf and slide to the desired location.

2. Lower shelf to the level position.

NOTE: You do not have to remove small items from the shelf

before moving it from side to side. You may need to remove

larger items.

The shelves in your refrigerator are adjustable to meet your

individual storage needs. Your model may have glass or wire

shelves.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy.

IMPORTANT: Do not clean glass shelves with warm water when

they are cold. Shelves may break if exposed to sudden

temperature changes or impact, such as bumping. For your

protection, tempered glass is designed to shatter into many small

pebble-size pieces. This is normal.

NOTE: Glass shelves are heavy. Use special care when removing

them to avoid impact from dropping.

Slide-out Shelves (on some models)

• To slide out shelf, carefully pull front of shelf toward you.

• To slide in shelf, push shelf in until it stops.

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop.

2. Tilt the front of the shelf up and lift it slightly as you pull the

shelf from the frame.

31 Replace the shelf by guiding it back into the slots on the

frame and pushing the shelf in past the stop,

To remove the shelf:

NOTE: The shelf is heavy and must be removed using both

hands.

1. Hold the back of the shelf with one hand.

2. Lift the front of the shelf with the other hand to a 45° angle

and lower it slightly to release it from the upper channel of the

track. Pull the shelf straight out.

To remove and replace the shelf track:

1. Remove the shelf track by lifting both sides of the track

slightly and pulling the track straight out,

2. Replace the track by guiding the track hooks into the shelf

support slots on the back wall.

NOTE: Make sure that both sets of track hooks are in the

slots and that the slots are parallel with each other,

3. Push the track back and down securely into the shelf

supports.

To replace the shelf:

NOTE: Make sure that both of the rear shelf slides are securely in

the track before letting go of the shelf. The lateral shelf may be

difficult to install if the track is placed too close to the refrigerator

ceiling. Reposition the track on a lower rung until the shelf can be

tilted enough to easily slide into the track.

1. Hold the shelf at the front and tip the front at a 45 ° angle to

the track.

2. Insert both of the rear shelf slides into the upper channel of

the track, and lower the front of the shelf into place.

1. Toraisetheshelf,pullforwardontheleverlocatedatthe

bottomfrontoftheshelfandliftuntiltheshelflocksintothe

verticalposition.

2. Tolowertheshelf,lowertheshelfuntilitislatchedsecurelyin

place.

Toremoveandreplacethecrisperandconvertiblevegetable

meatdrawers:

1. Slidecrisperormeatdrawerstraightouttothestop.Liftthe

frontofdrawerwithonehandwhilesupportingthebottomof

drawerwithotherhandandslidethedrawerouttherestof

theway.

2. Replacethecrisperormeatdrawerbyslidingitbackinfully

pastthedrawerstop.

To raise and lower the shelf:

1. Raise the shelf by first sliding it back and down to make it

half-width. (You can use the shelf in this position to allow

taller items to be stored on the shelf below.)

2. Lift the front of the shelf until it fits securely in place against

the back wall.

3. Lower the shelf securely back into position.

4. Pull the front of the shelf forward until it fits into place.

IMPORTANT: Do not clean crisper/meat drawer covers with

warm water when they are cold, Covers may break if exposed to

sudden temperature changes or impact, such as bumping, For

your protection tempered glass is designed to shatter into many

small pebble-size pieces, This is normal,

NOTE: Glass crisper/meat drawer shelves are heavy, Use special

care when removing them to avoid impact from dropping,

To remove and replace the crisper or vegetable/meat drawer

covers:

1. Remove the crisper and meat drawer. Press up in center of

crisper glass insert until it rises above the plastic frame.

Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame up and remove. Repeat steps to

remove the meat drawer cover.

The dell drawer stores raisins, nuts, spreads, and other small

items at normal refrigerator temperatures.

To remove and replace the dell drawer:

1. Remove the dell drawer by sliding it straight out to the stop.

Lift the front and slide the drawer out the rest of the way.

2. Replace the dell drawer by sliding it back past the stop.

3. Replace back of meat drawer cover frame into supports on

side walls of the refrigerator and lower the front of the cover

frame into place.

4. Slide rear of glass insert into cover frame and lower front into

place. Repeat steps to replace the crisper cover.

Meat storage guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish .................. use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ............................................................ 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

The convertible vegetable/meat drawer can be adjusted to

properly chill meats or vegetables. The air inside the pan is

cooled to prevent "spot" freezing and can be set to keep meats

at the National Livestock and Meat Board recommended storage

temperatures of 28°- 32°F (-2° - O°C).

IMPORTANT: To extend freshness, wrap meats in airtight,

moisture-proof materials before storing. Always store meat as

recommended.

Adjusting the control

The convertible control comes preset at the lowest meat setting.

To change a control setting: Move the control to the right

(colder) or to the left (less cold) as desired.

To store vegetables: Set the control at the VEG setting, all the

way to the left, to store vegetables at their optimal storage

temperatures (which need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the left

(less cold). Remember to wait 24 hours between adjustments.

Doing so gives the temperature of the food time to change.

S _< S

Depending on your model, you may have a one piece utility bin or

a three piece egg bin. To use the three piece egg bin, remove the

cover and place the eggs in the egg tray, Replace cover and store

on an interior refrigerator shelf, If you prefer, you can remove the

egg tray and place the entire carton of eggs in the bin. Replace

the cover,

NOTE: Eggs should be stored in a covered container. If your

model does not have an egg bin or covered utility bin, store

eggs in their original container on an interior shelf.

%:: <

• P_,::c<:s_( %'

To remove and replace the wine rack (left) or can/bottle rack

(right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

• LOW (open) lets moist air out of the crisper for best storage

of fruits and vegetables with skins.

Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

Vegetables with skins: Place in plastic bags or plastic

container and store in crisper.

• HIGH (closed) keeps moist air in the crisper for best storage

of fresh, leafy vegetables.

Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

Humidity control location:

• Humidity Control on crisper drawer (Style 1 - on left)

• Humidity Control on crisper cover (Style 2 - on right)

\ Humidity Control

/f/GNoo®6oooo LO_V

\:" High 5 4 3 2 1 Low

FREEZER FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one or the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

To turn the ice maker on:

s ?:_ g} ;,

Style 1 - Normal and Maximum Ice Maker

The on/off switch for the ice maker is a wire shut-off arm located

on the side or the ice maker. To turn the ice maker on, simply

lower the wire shut-off arm.

NOTE: The ice maker will not make ice until the freezer is cold

enough. Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced.

To turn the ice maker off:

• Automatic turn off: As ice is made, the ice cubes will fill the

ice storage bin. The ice cubes will raise the wire shut-off arm

to the OFF (arm up) position.

• Manual turn off: Lift the wire shut-off arm to the OFF (arm up)

position and listen for the click to make sure the ice maker

will not continue to operate.

• To increase ice production rate: Maximum Ice Production (on

some models): In maximum ice production, the ice maker

should produce approximately 10 to 14 batches of ice in a

24-hour period. If your refrigerator has the maximum ice

production feature, push the switch to MAX.

• Normal Ice Production: In normal ice production mode, the

ice maker should produce approximately 7 to 9 batches of ice

in a 24-hour period. If ice is not being made fast enough, turn

the Freezer Control toward a higher (colder) number in half

number steps. (For example, if the control is at 3, move it to

between 3 and 4.) Wait 24 hours and, if necessary, gradually

turn the Freezer Control to the highest setting, waiting 24

hours between each increase.

Style 1 - Ice Maker Storage Bin

To remove and replace the ice bin:

l i Pull the covering panel out from the bottom and then slide it

back toward the rear.

2. Lift the wire shut-off arm so it clicks into the OFF (up)

position. Ice can still be dispensed, but no more can be

made.

31 Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shut-off arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Style 2 - Ice Maker

To turn the ice maker on:

The ON/OFF switch is located on the top right side of the freezer

compartment. Toturn the ice maker on, slide the control to the

ON (left) position.

NOTE: The ice maker will not make ice until the freezer is cold

enough. Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced.

To turn the ice maker off:

• Automatic turn off: The ice maker sensors will automatically

stop ice production but the control will remain in the ON (left)

position.

• Manual turn off: Slide the control to the OFF (right) position.

Style 2 - Ice Storage Bucket

To remove and replace ice bucket:

1. Place four fingers in bucket base opening and rest thumb on

the release button.

2. Holding the base of the bucket with both hands, depress the

release button and lift the bucket up and out. It is not

necessary to turn the ice maker control to the OFF (right)

position. The ice maker will not produce ice without the

bucket installed in the door.

To care for ice storage bin or bucket (Styles 1 and 2)

1. Empty the ice container. Use warm water to melt the ice if

necessary. Never use anything sharp to break up the ice in

the bin or bucket. This can cause damage to the ice container

and the dispenser mechanism.

2. Wash with a mild detergent, rinse well and dry thoroughly. Do

not use harsh or abrasive cleaners or solvents.

REMEMBER:

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

• Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

• Do not force the wire shut-oft arm up or down.

• Do not store anything on top of the ice maker or in the ice

storage bin.

To remove and replace the shelf:

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

3. Replace shelf in the reverse order.

Frozen food storage guide

t I',11

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-prooO, and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2-3 Ib of food per cubic foot [907-1,350 g

per L] of freezer space). Leave enough space in the freezer for air

to circulate around packages. Be careful to leave enough room

for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

The freezer basket can be used to store bags of frozen fruits and

vegetables that may slide oft freezer shelves.

To remove and replace the freezer basket:

1. Remove basket by sliding it out to the stop.

2. Lift the front of the basket and slide it out the rest of the way.

31 Replace the basket by positioning it on the side wall guide

rails. Lift the basket front slightly while pushing it past the

guide rail stops and slide basket in the rest of the way.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To remove and replace the rails:

11 Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

9Lh,_ t_'_

To remove and replace the bins:

1. Remove the bin by lifting it up and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

To remove and replace the rack:

1. Remove the rack by lifting it up and pulling straight out.

2. Replace the rack by holding it above the desired support and

pushing the rack back and down until it stops.

CARING FOR YOUR

REFRIGERATOR

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts interior

and door liners or gaskets.

• Do not use paper towels, scouring pads, or other harsh

cleaning tools. These can scratch or damage materials.

• To help remove odors, wash interior walls with a mixture

of warm water and baking soda (2 tbs. to 1 qt.

[26 g to .95 L] of water).

4. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Dry thoroughly with a soft

cloth.

For additional protection against damage to painted metal

exteriors, apply appliance wax (or auto paste wax) with a

clean, soft cloth. Do not wax plastic parts.

5. Clean the condenser coils regularly. Coils may need to be

cleaned as often as every other month. This may help save

energy

Style 1 - Condenser coils behind base grille:

• Remove the base grille (see the "Base Grille" section).

• Use a vacuum with an extended attachment to clean the

condenser coils when they are dusty or dirty.

• Replace the base grille when finished.

Style 2 - Condenser coils in back of the refrigerator:

• Pull refrigerator out away from the wall (see the

"Unpacking Your Refrigerator" section).

• Vacuum coils when they are dusty or dirty.

• Roll refrigerator back into place. Make sure to leave 1 in.

(2.5 cm) between the cabinet back and the wall.

• Check to see if the refrigerator is level.

6. Plug in refrigerator or reconnect power.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion,

or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To clean your refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size and shape. The

dispenser light requires a heavy duty 10-watt bulb. All other lights

require a 40-watt appliance bulb. Replacement bulbs are

available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown.

NOTE: To clean a light shield, wash it with warm water and a

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,

shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

Dispenser Light (on some models)

Reach through the dispenser area to remove and replace light

bulb.

.......................1

7. Dispenser Light

Control Panel Light

Reach behind the refrigerator control panel to remove and

replace light bulb.

Crisper Light or Upper Freezer Light (on some models)

• Remove light shield by grasping the top center of the shield

and pulling forward while turning it slightly to one side. If

necessary, remove top crisper drawer to access crisper light

shield.

Replace the light shield by inserting the tabs on one end into

the slotted holes in the refrigerator or freezer liner. Then,

carefully bend the shield at the center to insert the tabs on

the other end.

Upper Freezer Light (on some models)

• Remove the light shield by grasping the sides and squeezing

in towards the center and while pulling forward the shield.

• Replace the light shield by fitting the tabs into the slotted

holes in the freezer liner. Push in the shield until it snaps into

place.

Lower Freezer Light (on some models) - (located beneath

ice bin)

• Remove the light shield by grasping the sides and squeezing

in towards the center. Once the side hooks of shield are free

from the freezer lining, pull down the shield.

• Replace the light shield by squeezing the sides towards the

center and inserting the side hooks into the slotted holes.

Once the side hooks are in place, snap the front tab into the

slotted hole.

Lower Freezer Light (on some models) - (located behind

top freezer basket)

• Remove the top freezer basket. Remove light shield by

grasping the top and bottom center of the shield and pulling

forward while turning it slightly to one side until one of the

side tabs become free. Pull out tab from other end and

remove shield.

• Replace the light shield by inserting the tabs on one end into

the slotted hole in the freezer liner. Then, carefully bend the

shield at the center to insert the tabs on the other end.

If the electricity in your house goes off, call the power company

and ask how long it will be off.

1. If the power will be out for 24 hours or loss, keep both

refrigerator doors closed to help food stay cold and frozen.

2. If the power will be out for more than 24 hours:

a) Remove all frozen food and store it in a frozen food

locker.

b) Place 2 Ibs (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen

for two to four days.

c) If neither a food locker nor dry ice is available, consume

or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. Ifyou see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the rood is poor, dispose of it.

Vacations

If you choose to leave the refrigerator on while you're away,

use these steps to prepare your refrigerator before you leave.

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shut-off arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave,

follow these steps,

1. Remove all rood from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shut-off

arm to the OFF (up) position or move the switch to the

OFF (right) setting.

3. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFE See the "Setting the Controls"

section.

4. Clean refrigerator, wipe it, and dry well.

La page charge ...

KitchenAid KSRS22FGBT04 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSRS22FGBT04

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KSRS22FGBT04 Owner's manual

KitchenAid KSRS22FGBT04 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KSRS22FGBT04 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents