KitchenAid KSRU25CRWH00 Le manuel du propriétaire
- Catégorie
- Frigos
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
®itchen_kid ®
SIDE BY SIDE REFRIGERATOR
i]i!!!i!i_:_ii!i!!_¸,,_:!i!il;_:_:¸(]il;iiiii_i_'_i:_!_(]iii_ii;_iii_;::li_i!!_¸
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...
www.kitchenaid.com or www.KitchenAid.ca
P P _ '_ A
REFRIGERATEUR COTE A COTE
Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777 ou visitez notre site web &...
www.KitchenAid.ca
Table of Contents/Table des matieres ............................................................................. 2
2308307
TABLEOF CONTENTS
REFRIGERATOR SAFETY ............................................................. 3
Proper Disposal of Your Old Refrigerator .................................... 3
INSTALLATION INSTRUCTIONS .................................................. 4
Unpack the Refrigerator ............................................................... 4
Location Requirements ................................................................ 4
Electrical Requirements ............................................................... 5
Water Supply Requirements ........................................................ 5
Base Grille .................................................................................... 5
Refrigerator Doors ........................................................................ 6
Adjust the Doors ........................................................................... 7
Connect the Water Supply ........................................................... 8
Prepare the Water System ........................................................... 9
Factory Trim Kit ............................................................................ 9
Normal Sounds .......................................................................... 11
REFRIGERATOR USE .................................................................. 11
Ensuring Proper Air Circulation .................................................. 11
Using the Controls ..................................................................... 11
Water and Ice Dispensers .......................................................... 14
Water Filter Status Light ............................................................. 15
Water Filtration System .............................................................. 15
Ice Maker and Storage Bin ........................................................ 16
REFRIGERATOR FEATURES ...................................................... 17
Refrigerator Shelves ................................................................... 17
Deft Drawer ................................................................................. 17
Convertible Vegetable/Meat Drawer, Crisper and Covers ........17
Convertible Vegetable/Meat Drawer Temperature Control .......18
Crisper Humidity Control ............................................................ 18
Wine Rack .................................................................................. 18
Utility Bin..................................................................................... 18
FREEZER FEATURES .................................................................. 18
Freezer Shelf ............................................................................... 18
Freezer Basket or Bin ................................................................. 19
DOOR FEATURES ........................................................................ 19
Tilt-out Freezer Door Bin ............................................................ 19
Snap-on Freezer Door Bin ......................................................... 19
Drop-in Door Rails ...................................................................... 19
Can Racks and Door Bins .......................................................... 19
Door Air Control .......................................................................... 20
REFRIGERATOR CARE ............................................................... 20
Cleaning ...................................................................................... 20
Changing the Light Bulbs ........................................................... 21
Power Interruptions .................................................................... 21
Vacation and Moving Care ......................................................... 22
TROUBLESHOOTING .................................................................. 22
ASSISTANCE OR SERVICE ......................................................... 25
In the U.S.A................................................................................ 25
In Canada ................................................................................... 25
Accessories ................................................................................ 25
WATER FILTER CERTIFICATIONS ............................................. 26
PRODUCT DATA SHEETS ........................................................... 27
WARRANTY .................................................................................. 28
TABLE DES MATIERES
SECURITI :!:DU RI:!:FRIGI:!:RATEUR.............................................. 30
Mise au rebut de votre vieux refrigerateur ................................. 30
INSTRUCTIONS D'INSTALLATION ............................................ 31
Deballage du refrigerateur ......................................................... 31
Emplacement d'installation ........................................................ 31
Specifications electriques .......................................................... 32
Specifications de I'alimentation en eau ..................................... 32
Grille de la base .......................................................................... 32
Portes du refrigerateur ............................................................... 33
Ajuster les portes ........................................................................ 35
Raccordement de la canalisation d'eau .................................... 35
Preparer le syst_me d'eau ......................................................... 36
Ensembles decoratifs de I'usine ................................................ 37
Sons normaux ............................................................................ 38
UTILISATION DU RI:!:FRIGERATEUR .......................................... 39
Pour s'assurer d'une circulation d'air appropriee ..................... 39
Utilisation des commandes ........................................................ 39
Distributeurs d'eau et de glagons .............................................. 41
Le temoin lumineux de I'etat du filtre a eau ............................... 43
Systeme de filtration d'eau ........................................................ 43
Machine a glagons et bac d'entreposage ................................. 44
CARACTI_RISTIQUES DU RI_FRIGI_RATEUR ........................... 45
Tablettes du refrigGrateur ........................................................... 45
Tiroir pour specialites alimentaires ............................................ 45
Tiroir a legumes/viande convertible,
bac a legumes et couvercles ..................................................... 45
Reglage de la temperature du tiroir
legumes/viande convertible ....................................................... 46
Reglage de I'humidite dans le bac a legumes ........................... 46
Casier a vin ................................................................................. 46
Casier utilitaire ............................................................................ 46
CARACTI_RISTIQUES DU CONGI_LATEUR ............................... 47
Tablette de congelateur ............................................................. 47
Panier ou bac de congelateur .................................................... 47
CARACTI_RISTIQUES DE LA PORTE ......................................... 47
Compartiment inclinable de la porte du congelateur ................ 47
Compartiment encliquetable de la porte du congelateur .......... 47
Tringles deposees dans la porte ................................................ 48
Porte-cannettes et balconnets ................................................... 48
Commande d'air de la porte ...................................................... 48
ENTRETIEN DU RI_FRIGI:!:RATEUR ............................................ 48
Nettoyage ................................................................................... 48
Remplacement des ampoules d'eclairage ................................ 49
Pannes de courant ..................................................................... 50
Entretien avant les vacances ou Iors d'un demGnagement .......50
DI_PANNAGE ................................................................................. 51
ASSISTANCE OU SERVICE ......................................................... 54
Accessoires ................................................................................ 54
FEUILLES DE DONNI_ES SUR LE PRODUIT ............................. 55
GARANTIE ..................................................................................... 56
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
mPlug into a grounded 3 prong outlet, m Use nonflammable cleaner.
mDo not remove ground prong.
mDo not use an adapter.
mDo not use an extension cord.
mDisconnect power before servicing.
mReplace all parts and panels before operating.
mRemove doors from your old refrigerator.
m Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
m Use two or more people to move and install refrigerator.
m Disconnect power before installing ice maker (on ice maker
kit ready models only).
m Use a sturdy glass when dispensing ice or water (on some
models).
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Old Refrigerator
Before you throw away your old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily
climb inside.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
INSTALLATION INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
• Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information see "Refrigerator Safety."
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pulI the refrigerator straight out when moving it.
Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in "Refrigerator Care."
_mportant information to know about glass she_ves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal Glass
shelves and covers are heavy. Use special care when
removing them to avoid impact from dropping.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your refrigerator, allow for 1/2"
(1.25 cm) space on each side and at the top. When installing your
refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on
each side (depending on your model) to allow for the door to
swing open. If your refrigerator has an ice maker, allow extra
space at the back for the water line connections.
NOTE: It is recommended that you do not install the refrigerator
near an oven, radiator, or other heat source. Do not install in a
location where the temperature will fall below 55°F (13°C).
mjl,
y,
/,
112"(1.25 cm):
II -- !
J
2" {5.08 cml
ElectricalShockHazard
Plugintoagrounded3prongoutlet.
Donotremovegroundprong.
Donotuseanadapter.
Donotuseanextensioncord.
Failuretofollowthese}nstructionscanresult }n death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator
or Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
IMPORTANT:
• If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
• All installations must meet local plumbing code requirements.
• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
TOOLS NEEDED: Fiat-blade screwdriver, 7/16"and 1/2"open-end
wrenches or two adjustable wrenches, 1/4"nut driver and drill bit,
hand drill or electric drill (properly grounded).
NOTE: Your refrigerator dealer has a kit available with a 1/4"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3/16"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
Water Pressure
A cold water supply with water pressure of between 30 and
120 psi (207 - 827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 - 414 kPa):
• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
If your refrigerator has a water filter cartridge, it may further
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.
See "Water Filtration System."
If you have questions about your water pressure, call a licensed,
qualified plumber.
Remove the Base Grille:
1. Open both doors.
2. Place hands along the ends of the grille. Push in on the top of
the base grille and pull up on the bottom.
NOTE: Be sure to refasten the Tech Sheet behind the base grille
after cleaning.
Replace the Base Grille:
1. Open both doors.
2. Line up the grille support tabs with the metal clips.
3. Push the grille firmly to snap it into place.
TOOLSNEEDED:1/4",1/2",and%6"hex-headsocketwrenches,afiat-bladescrewdriverandaPhillipsscrewdriver,
IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFEUnplugrefrigeratorordisconnectpower.Removefoodandany
adjustabledoororutilitybinsfromdoors,
ElectricamShockHazard
Disconnect power before removing doors.
Reconnect both ground wires before operating,
Failure to do so can result in death or electrical shock.
Top Left Hinge
A. Do Not Remove Screw
I
A
A. Red Outer Ring
Door RemovaJ
I
o_ooo
Top Right Hinge
A. Do Not Remove Screw
Bottom Hinge
A. Do Not Remove Screw
Door AJignment
A J
A. Leveling Screw
ElectricamShockHazard
Disconnectpowerbeforeremovingdoors,
Faimuretodosocanresumtin death or electricam shock,
l
1. Unplug refrigerator or disconnect power.
2. Open both refrigerator doors. Remove the base grille by
pulling up on the bottom outside corners. See Graphic 1.
3. Close both doors and keep them closed until you are ready to
lift them free from the cabinet.
4. If you have a dispenser (ice or water), disconnect the water
dispenser tubing located behind the base grille on the freezer
door side. See Graphic 2.
• Press the red outer ring against the face of fitting and pull
the dispenser tubing free.
• On some models, remove tubing from hose clip.
5. Remove top left hinge screw and cover as shown in
Graphic 3.
6. Disconnect wiring plug and both ground wires from the
ground wire screw (on some models) as shown in Graphic 3.
7. Remove remaining left hinge screws and hinge as shown in
Graphic 3. Do not remove screw A.
8. Lift freezer door straight up off bottom hinge. See Graphic 4.
The water dispenser tubing remains attached to the freezer
door and pulls through the bottom left hinge. Make sure you
protect the dispenser tubing from damage.
9. Remove top right hinge cover and screws as shown in
Graphic 5. Do not remove screw A.
10. Lift the refrigerator door straight up off bottom hinge.
11. It may not be necessary to remove the bottom hinge to move
the refrigerator through a doorway. Both bottom hinges have
similar construction.
• Disassemble the hinges as shown in Graphic 6.
Do not remove screw A.
Replace the Doors and Hinges
1. Replace both bottom hinges, if removed. Tighten screws.
2. Assistance may be needed to feed the water dispenser
tubing through the bottom hinge while reinstalling the freezer
door. Feed the dispenser tubing through the bottom left hinge
before replacing the door on the hinge.
NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Reconnect water dispenser tubing by pushing tubing into
fitting until it stops and black mark touches the face of the red
outer ring. See Graphic 2. On some models, replace tubing in
hose clip.
Electricam Shock Hazard
Reconnect both ground wires.
Failure to do so can resumt in death or electrical shock.
Style 1
• Reconnect both ground wires.
• Reconnect wiring plug.
A.Do not remove screw A
B. Ground wires
C.Green ground wire screw
D. Wiringplug
Style 2
• Reconnect wiring plug.
5. Replace left hinge cover and screws.
6. Replace the refrigerator door by lifting the door onto the
bottom right hinge.
7. Align and replace the top right hinge as shown in Graphic 5.
Tighten screws.
8. Replace hinge cover and screws. Tighten screws.
9. Plug into a grounded 3 prong outlet.
Your refrigerator has two front adjustable rollers -- one on the
right and one on the left. If your refrigerator seems unsteady or if
you want the doors to close more easily, adjust the refrigerator's
tilt using the instructions below.
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
1. Move the refrigerator into its final position.
2. The two leveling screws are part of the front roller assemblies
which are at the base of the refrigerator on either side. See
Graphic 7.
3=
Use a hex-head socket wrench to adjust the leveling screws.
Turn the leveling screw to the right to raise that side of the
refrigerator or turn the leveling screw to the left to lower that
side. It may take several turns of the leveling screws to adjust
the tilt of the refrigerator. See Graphic 7.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and
rollers. This makes it easier to adjust the screws.
4. Open both doors again and check to make sure that they
close as easily as you like. If not, tilt the refrigerator slightly
more to the rear by turning both leveling screws to the right. It
may take several more turns, and you should turn both
leveling screws the same amount.
5. Replace the base grille.
NOTE: Be sure to refasten the Tech Sheet behind the base grille.
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker OFR
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a 1/2"(12.70 mm)to 11/4"(3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
4.
5=
6=
• Make sure it is a cold water pipe.
• Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
Determine the length of copper tubing you need. Measure
from the connection on the lower rear corner of the
refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for
cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper
tubing. Be sure both ends of copper tubing are cut square.
Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold
water pipe you have selected.
...... A
G .............................B
.... .... C
A. CoM water pipe E Compression sleeve
B.Pipe clamp F.Shutoff valve
C. Copper tubing G.Packing nut
D.Compression nut
Fasten shutoff valve to cold water pipe with pipe clamp. Be
sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the
water pipe and that washer is under the pipe clamp. Tighten
packing nut. Tighten the pipe clamp screws slowly and
evenly so the washer makes a watertight seal. Do not
overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw the compression
nut onto the outlet end with an adjustable wrench. Do not
overtighten.
8. Place the free end of the tubing into a container or sink, and
turn ON main water supply and flush out the tubing until
water is clear. Turn OFF the shutoff valve on the water pipe.
Coil the copper tubing.
Connect to Refrigerator
Style 1
1. Unplug refrigerator or disconnect power.
2. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
3. A 1/4"x 1/4"coupling is needed to order to connect the water
tubing to an existing household water supply line. Thread the
provided nut onto the coupling on the end of the copper
tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
4.
5.
A B C
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb
D. Coupling (provided)
Turn shutoff valve ON.
Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
D E F G
E.Ferrule (purchased)
F Nut (purchased)
G, Household water line
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
3. Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
A
B
4.
5.
A.Bulb
B.Nut (provided)
Turn shutoff valve ON.
Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Complete the Installation
E_ectrical Shock Hazard
P_ug into a grounded 3 prong outlet°
Do not remove ground prong,
Do not use an adapter,
Do not use an extension cord°
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug in refrigerator or reconnect power.
2. Flush the water system. See "Prepare the Water System."
NOTE: It may take up to 24 hours for your ice maker to begin
producing ice.
Please read before using the water system.
Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.
1. Open the freezer door and turn off the ice maker. For Style f,
lift up the wire shutoff arm as shown. For Style 2, move the
switch to the OFF (right) setting as shown. The ON/OFF
switch is located on the top right side of the freezer
compartment.
Style 1
Style 2
Use a sturdy container to depress the water dispenser bar
until the water begins to flow. Flush the water system by
dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.
Cleaning the system will take approximately 6 to 7 minutes
and will help clear air from the line. Additional flushing may be
required in some households.
NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
Open the freezer door and turn on the ice maker. For Style f,
lower the wire shutoff arm. For Style 2, move the switch to
the ON (left) position. Please refer to the "Ice Maker and
Storage Bin" section for further instructions on the operation
of your ice maker.
• Allow 24 hours to produce the first batch of ice.
• Discard the first three batches of ice produced.
• Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
O
There may be an occasion when you will need to remove the
factory-installed trim kit, such as moving the refrigerator to a new
home or installing custom-made decorator panels. Please read
all instructions before removing the trim kit and decorator panels.
Freezer Door Refrigerator Door
B A
.......................C .........................
A
A. Decorator panels
B. Filler panels
C. Handles
NOTES:
• If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cartridge cap
handle is in the horizontal position.
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
RemovetheDoorPanels
NOTE:When removing and replacing decorator panels, only the
handle is removed. All other trim pieces remain attached to the
doors.
1. Remove the refrigerator and freezer handles:
• Using a Phillips screwdriver, remove the screws that hold
each handle in place.
• Lift off handle. Make sure you keep screws for reattaching
handles.
2. Remove the door panels:
• Open refrigerator or freezer door.
• Slide out decorator panel and filler board.
• Repeat process for other panels and filler boards.
• Store panel and filler boards to prevent scratching.
Replace the Door Panels
1. Replace the refrigerator or freezer door panels:
• Open refrigerator or freezer door.
• Slide the 1/8"(3.18 mm) decorator panel into place behind
the side trim.
• Push the filler board into place behind the decorator
panel.
• Repeat process for other panels and filler boards.
2. Attach the handles:
NOTE: Freezer door handle is notched to fit around the
dispenser panel.
• Align the top of the refrigerator or freezer handle flush
with the top trim. Fasten the handle to the refrigerator or
freezer door with the screws, using a Phillips screwdriver.
• Repeat the process for the other handle.
Care for Decorator Panels
1. Clean panels with an anti-static cleaner (available in
electronics or computer departments) or mild soap and water
with a clean, soft, damp cloth.
2. Rinse panels thoroughly and blot dry using a dry, soft cloth or
chamois.
NOTE: Do not use paper towels or cleaners which contain
solvents such as ammonia. They can damage the surface of
the panels.
3. If small scratches should appear on the panels, they may be
filled using an automotive paste wax (not a cleaner/wax
combination). Apply wax sparingly and buff lightly with a
clean, soft cloth using a circular motion.
Install Custom Wood Panels
If you plan to install custom wood decorator panels, you will need
to create the panels yourself or consult your cabinetmaker or
carpenter. See dimensional drawings for wood panel inserts.
Flat panels:
You can create a custom flat panel a maximum of 1/4"(6.35 mm)
thick to replace your decorator panels. Flat wood panels less
than 1/4"(6.35 mm) thick are not recommended.
Raised panels:
A raised panel design can be created by screwing or gluing wood
panels to 1/4"(6.35 mm) backing or by using 8/4"(19.05 mm) stock
with routed edges.
Weight requirements for raised panel inserts:
• Refrigerator door panel should not exceed 25 Ibs.
(9.98 kg).
• Freezer door panels should not exceed 18 Ibs. (6.80 kg)
combined weight.
Dimensions for Custom Wood Panels:
22 cu. ft Freezer and Refrigerator door
1/4"
(6.35 rnm)
/ I_ I 18s/32"
'((3127/16"
1.6 cm) '
__127/16,,._ 6011164"
(154.2 cm)
=(31,6 cm)
(7,93mmQ
(6.35ram)
3/4"rain. 3_/4" _!4"
(19.05mmrain.)(82.55mmrain.) ......
_'_---_u_ ram,
TOP VIEW "_ f
1/4"
(635ram)
1/4"
(6.35 rnm)
5/16"
(7.93 mm
5/16"
7.93 ram)
(6.35 mm)
3_I4" _/4"min. _!4"
(82.55mmrain.)(19.05rammin.)_19.05ram,
TOP VIEW f "_
1/4"
(635ram)
10
25 cu. ft Freezer and Refrigerator door
i
I
' 28%4"
(7.93ram)@
(6.35 mm) (6.35 ram)
3/4"rnin. 31/4 `` s/,, 31/4' 3/4"rain. 3/4,,
(19.05rnmrnin.) (8255mmrnin) ,,-_,_ ,
(82,55rnrnrnin.)(19.05mrnrnin.)(19,05ram)
k
TOP VIEW _ TOP VIEW _
V4" ¼
(6.aSram) (&35ram)
V4"
(6.35 mm)
__)
X s/16,,
/)(7,93 mm)
-,_, 191S/le ''-
,(60,7cm)
5/16,,
7,93 mm)
Dimensions for Routing Handle Side of Door Panel
(End View)
Route entire areas of handle side of panels31/4''(8.25 cm).
@
¢d
I
31/4`'
(8.25rain..cm) _1
+_ Door
2" (5 cm)
rain.
Hinge Side
__l
Door I H_
Panel
1"
(2.54 cm)
Your new refrigerator may make sounds that your old one didn't
make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, such as the floor, walls, and cabinets, can make the
sounds seem louder. The following describes the kinds of sounds
and what may be making them.
• If your refrigerator is equipped with an ice maker, you will hear
a buzzing sound when the water valve opens to fill the ice
maker for each cycle.
Your refrigerator is designed to run more efficiently, to keep
your food items at the desired temperatures and to minimize
energy usage. The high efficiency compressor and fans may
cause your refrigerator to run longer than your old one. You
may also hear a pulsating or high-pitched sound from the
compressor or fans adjusting to optimize performance.
You may hear the evaporator fan motor circulating air through
the refrigerator and freezer compartments. The fan speed
may increase as you open the doors or add warm food.
Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
Water dripping on the defrost heater during a defrost cycle
may cause a sizzling sound.
As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your refrigerator.
Contraction and expansion of the inside walls may cause a
popping noise.
You may hear air being forced over the condenser by the
condenser fan.
You may hear water running into the drain pan during the
defrost cycle.
REFRIGERATOR USE
In order to ensure proper temperatures, you need to permit air to
flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator
section through the top vent. Air then returns to the freezer as
shown.
/
Do not block any of these vents with food such as soda, cereal,
bread, etc. If the vents are blocked, airflow will be prevented and
the temperature controls will not function properly.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer from food, wrap or cover foods tightly.
Your model may have Slide Controls, Electronic Controls or
Digital Controls.
IMPORTANT (All Controls):
• The Refrigerator control adjusts the refrigerator compartment
temperature. The Freezer control adjusts the freezer
compartment temperature.
• Wait 24 hours after you turn on the refrigerator before you put
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the Refrigerator and Freezer controls to a
lower (colder) setting will not cool the compartments any
faster.
11
• If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
• The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
Slide Controls (on some models)
For your convenience, your controls are preset at the factory.
When installing your refrigerator, make sure that the controls are
still preset to the "mid-settings" as shown.
Style 1
Freezer Refrigerator
C
cold I 2 A 3 4 colder off I 2 _, 3 4 colder
Style 2
Freezer Refrigerator
Off I 2 =, 3 4 Colder Cold I 2 A 3 4 Colder
IMPORTANT:
• For Style 1, your product will not cool when the Refrigerator
control is set to OFE For Style 2, your product will not cool
when the Freezer Control is set to OFR
• Settings to the left of the mid-setting make the temperature
less cold. Settings to the right of the mid-setting make the
temperature colder.
• The Automatic Exterior Moisture control continuously guards
against moisture buildup on the outside of your refrigerator
cabinet. This control does not have to be set or adjusted.
Adjusting Slide Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
If you need to adjust temperatures:
• Slide the FREEZER or REFRIGERATOR control, one setting to
the right or left depending on the needed temperature
change.
NOTE: For Style 1, after adjusting the refrigerator
temperature, wait 24 hours and then recheck the FREEZER
temperature before making additional adjustments.
CONDITION: SETTING ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR Control
Not set correctly for conditions one setting lower
REFRIGERATOR too warm REFRIGERATOR Control
High use or room very warm one setting higher
FREEZER too cold FREEZER Control one
Not set correctly for conditions setting lower
FREEZER too warm/too little ice FREEZER Control one
High use or heavy ice usage setting higher
Electronic Controls (on some models)
For your convenience, your controls are preset at the factory.
When installing your refrigerator, make sure that the controls are
still preset to the "mid-settings" as shown.
FREEZER REFRIGERATOR
_ COlR COLOER _ COLR COLDER
_ 0 O,0qlD_ _
1 2 3 (_ 5 6 7
_i 2 3(#5 6 7
To turn on refrigerator:
• Press and hold ON/OFF for 2 seconds. The indicator lights
show the current temperature control settings.
NOTE: Settings to the left of the mid-setting make the
temperature less cold. Settings to the right of the mid-setting
make the temperature colder.
Adjusting Electronic Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
If you need to adjust temperatures:
• Press the FREEZER or REFRIGERATOR arrow to move the
indicator light to the right, one setting at a time. Continue
moving the indicator light until it is at the desired setting.
;oo , , ;
NOTE: With each press of the arrow, you will hear a beep as
the light moves to the next setting. The indicator light moves
to a setting of "7" and then returns to the setting of "1 ."
CONDITION: SETTING ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR Control
Not set correctly for conditions one setting lower
REFRIGERATOR too warm REFRIGERATOR Control
one setting higher
High use or room very warm
FREEZER too cold FREEZER Control one
Not set correctly for conditions setting lower
FREEZER too warm/too little ice FREEZER Control one
High use or heavy ice usage setting higher
Additional Electronic Control Panel Features
Additional features are located on the control panel at the top of
the refrigerator compartment.
Water Filter Indicator Light and Reset
See "Water FilterStatus Light."
12
Accelerated Ice Production
This feature assists with temporary periods of heavy ice usage by
increasing ice production over a 24-hour period.
• Press ICE touch pad to set the freezer temperature to -10°F
(-23°C). The Accelerated Ice setting will remain on for
24 hours unless manually turned off. The display will continue
to show your normal temperature set point.
@
If increased ice production is desired at all times, set the
Freezer Control to a colder setting. Adjusting the freezer to a
colder temperature may make some foods, such as ice
cream, harder.
Digital Controls (on some models)
For your convenience, your controls are preset at the factory.
When installing your refrigerator, make sure that the controls are
still preset to the "mid-settings" as shown. The digital control
panel is located at the top of the refrigerator compartment.
NOTE: The factory recommended set points are 0°F (-18°C) for
the freezer and 37°F (3°C) for the refrigerator.
To turn refrigerator on and view set points:
• Press and hold POWER (ON/OFF) pad for 2 seconds.
Warmer FREEZER REFRIGERATORWarmer
Colder Colder
To view the Celsius temperatures:
• Press the °C SELECT pad. The indicator will light up. To
redisplay degrees in Fahrenheit, press the °C SELECT pad
again.
°C
NOTE: If the freezer temperature is below zero, the negative sign
next to the freezer display will light up.
Adjusting Digital Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
To adjust set point temperatures:
• Press the refrigerator or freezer PLUS (+) or MINUS (-) pad
until the desired temperature is reached.
REFRIGERATORWormer
Colder
The set point range for the freezer is -5°F to 5°F (-21 °C to -15°C).
The set point range for the refrigerator is 33°F to 41°F
(1°C to 5°0).
CONDITION/REASON: "IEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR Control 1°
Not set correctly for conditions higher
REFRIGERATOR too warm REFRIGERATOR Control 1°
lower
High use or room very warm
FREEZER too cold FREEZER Control 1° higher
Not set correctly for conditions
FREEZER too warm/too little FREEZER Control 1° lower
ice
High use or heavy ice use
Additional Digital Control Panel Features
Additional features are located on the control panel at the top of
the refrigerator compartment.
Water Filter Indicator Light and Reset
See "Water FilterStatus Light."
Max Cool
The Max Cool feature assists with periods of heavy ice usage, full
grocery loads, or temporarily warm room temperatures.
• Press MAX COOL pad to turn on the Max Cool feature. The
Max Cool indicator light will remain on for 24 hours unless
manually turned off.
iilMoxCool
NOTE: The temperature display will not change. After
24 hours, the refrigerator returns to the previous temperature
set points.
Accelerated Ice Production (on some models)
This feature assists with temporary periods of heavy ice use by
increasing ice production over a 24-hour period.
• Press OPTIMICE touch pad to turn on the Optimlce TM feature.
The Optimlce TM setting will remain on for 24 hours unless
manually turned off.
If increased ice production is desired at all times, set the
Freezer Control to a colder number. Setting the freezer to a
colder temperature may make some foods, such as ice
cream, harder.
Temperature System
The Temperature System feature lets you know the compressor
or evaporator fan is running. It is normal for this indicator light to
be on.
Temperature
System
13
!o;! _i¸_ii_O_;ii! _i!¸iii_;i_b_;!i_ii:_ii!;!!!_ii
Cut Hazard
Use a sturdy glass when dispensing ice or water°
Faimureto do so can resumt in cuts,
Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed
ice, a special light that turns on when you use the dispenser, a
special AUTO mode, or a lock option to avoid unintentional
dispensing.
The Ice Dispenser
Ice dispenses from the ice maker storage bin in the freezer. When
the dispenser lever is pressed:
• A trap door opens in a chute between the dispenser and the
ice bin. Ice moves from the bin and falls through the chute.
• When you release the dispenser lever, the trap door closes
and the ice dispensing stops. The dispensing system will not
operate when the freezer door is open.
Some models dispense both cubed and crushed ice. Before
dispensing ice, select which type of ice you prefer. The button
controls are designed for easy use and cleaning.
Style 1 Style 2
ICE
CRUSH CUBE
Crushed Cubed
For crushed ice, cubes are crushed before they are dispensed.
This may cause a slight delay when dispensing crushed ice.
Noise from the ice crusher is normal, and pieces of ice may vary
in size. When changing from crushed to cubed, afew ounces of
crushed ice will be dispensed along with the first cubes.
To Dispense Ice:
1. Press button for the desired type of ice.
2. Press a sturdy glass against the ice dispenser lever. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to
the lever in order to activate the ice dispenser. Pressing hard
will not make the ice dispense faster or in greater quantities.
Remove the glass to stop dispensing.
NOTE: The first few batches of ice may have an off-flavor
from new plumbing and parts. Throw the ice away, Also, take
large amounts of ice from the ice bin, not through the
dispenser.
The Water Dispenser
If you did not flush the water system when the refrigerator was
first installed, press the water dispenser bar with asturdy glass or
jar until you draw and discard 2 to 3 gal. (8 to 12 L) or
approximately 6 to 7 minutes of water after water begins
dispensing. It will take 3 to 4 minutes for the water to begin
dispensing. The water you draw and discard cleans the system
and helps clear air from the lines. Allow several hours for the
refrigerator to cool down and chill water.
IMPORTANT: Depending on your model, the small removable
tray at the bottom of the dispenser is designed to catch small
spills and allow for easy cleaning. There is no drain in the tray.
The tray can be removed from the dispenser and carried to the
sink to be emptied or cleaned.
To Dispense Water:
1. Press a sturdy glass against the water dispenser lever.
2. Remove the glass to stop dispensing,
NOTE: Water may have an off-flavor if you do not use the
dispenser periodically. Dispense enough water every week to
maintain a fresh supply.
1 .............
The Dispenser Light
Style 1
The dispenser area has a light. It can be turned on manually by
pressing the ON button (touch pad or rocker switch).
On some models: Whenever you use the dispenser the lever will
automatically turn the light on.
LIGHT
OFF ON
NOTE: See "Changing the Light Bulbs" for information on
changing the dispenser light bulb.
Style 2
When you use the dispenser, the lever will automatically turn the
light on. If you want the light to be on continuously, you may
choose either ON or AUTO.
On Auto
©
UGHT
14
ON: Press the LIGHT button to turn the dispenser light on.
AUTO: Press the LIGHT button a second time to select the AUTO
mode. The dispenser light will automatically adjust to become
brighter as the room brightens, dimmer as the room darkens.
OFF: Press the LIGHT button a third time to turn the dispenser
light off.
The dispenser lights are LEDs which should not need to be
changed. If it appears that your dispenser lights are not working,
check to be sure that the light sensor is not blocked (in AUTO
mode). See "Troubleshooting" for more information.
The Dispenser Lock (on some models)
Your dispenser can be turned off for easy cleaning or to prevent
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the
refrigerator, to the ice maker, or to the dispenser light. It simply
deactivates the dispenser levers.
Style 1
To turn off the dispenser, press the LOCK button until the
indicator appears. The ice and water dispensers will not work. To
unlock the dispenser, press the UNLOCK button until the
indicator appears. Then continue to dispense ice or water as
usual.
DISPENSER
LOCK UNLOCK
Style 2
To turn off the dispenser, press and hold the LOCK OUT button
until the indicator appears. The ice and water dispensers will not
work. To unlock the dispenser, press the LOCK OUT button until
the indicator disappears. Then continue to dispense ice or water
as usual.
Lockout
©
Press &
HoUd
The water filter status light will help you know when to change
your water filter cartridge. The light will change from green to
yellow. This tells you that it is almost time to change the water
filter cartridge (90% of the filter life has been used). It is
recommended that you replace the base grille water filter
cartridge when the water filter indicator light changes to red OR
water flow to your water dispenser or ice maker decreases
noticeably. To change the base grille water filter cartridge, see
"Changing the Water Filter Cartridge."
After changing the water filter cartridge, reset the water filter
status light.
Style 1
Press the light switch 5 times within 10 seconds. The status light
will change from red to green.
......................................B
A. Status Light
B. Light Switch
Style 2
Press and hold the water filter reset button until the status light
turns green. Your reset button may be located on the water
dispenser or on the control panel in the refrigerator compartment.
Dispenser Control Panel
Light Sensor
Filter Indicator
_ • Good •
Green = Good
Y_llow = Order • Order
Red = Replace
•Change
Press &
HoUd
::.:,do
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction may
be used on disinfected waters that may contain filterable
cysts.
Changing the Water Filter Cartridge
1. Press the eject button to release the filter from the base grille.
2. Pull the filter straight out.
NOTE: There will be water in the cartridge. Some spilling may
occur.
3. Turn the cap counterclockwise to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
4. Align the ridge on the cap with the arrow on the new filter and
turn the cap until it snaps into place.
NOTE: You can run the dispenser without a filter. Your water
will not be filtered. Simply insert the cap all of the way into the
base grille and rotate the cap until it is firmly in place.
5. Remove the protective covers from the O-rings.
AB .................C_,,..._
A. Protective cover
B. O-rings
15
6. Push the filter into the base grille. The eject button will pop
back out when the filter is fully engaged.
7. Flush the water system. See "Flushing the Water System
After Replacing Filter."
Flushing the Water System After Replacing Filter
Use a sturdy container to depress the water dispenser bar until
the water begins to flow. Flush the water system by dispensing
and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the
system will take approximately 6 to 7 minutes and will help clear
air from the line. Additional flushing may be required in some
households.
NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
Style I Style 2
To Turn the Ice Maker On/Off:
The on/off switch for the ice maker is a wire shutoff arm located
on the side of the ice maker.
1. To turn the ice maker on, simply lower the wire shutoff arm.
NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes will fill the ice storage bin and the ice
cubes will raise the wire shutoff arm to the OFF (arm up)
position.
2. To manually turn the ice maker off, lift the wire shutoff arm to
the OFF (arm up) position and listen for the click to make sure
the ice maker will not continue to operate.
To Turn the Ice Maker On/Off:
The ON/OFF switch is located on the top right side of the freezer
compartment.
1. Toturn the ice maker on, slide the control to the ON (left)
position.
NOTE: Your ice maker has an automatic shutoff. The ice
maker sensors will automatically stop ice production, but the
control will remain in the ON (left) position.
2. To manually turn the ice maker off, slide the control to the
OFF (right) position.
To Remove and Replace Ice Storage Bin:
1. Pull the covering panel out from the bottom and then slide it
back toward the rear.
2. Lift the wire shutoff arm so it clicks into the OFF (up) position.
Ice can still be dispensed, but no more can be made.
3. Lift up the front of the storage bin and pull it out.
4=
Replace the bin by pushing it in all the way or the dispenser
will not work. Push the wire shutoff arm down to the ON
position to restart ice production. Make sure the door is
closed tightly.
To Remove and Replace the Ice Storage Bin:
1. Hold the base of the storage bin with both hands and press
the release button to lift the storage bin up and out.
NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The
sensor cover ("flipper door") on the left wall of the freezer
stops the ice maker from producing ice if the door is open or
the storage bin is removed.
2. Replace the storage bin on the door and push down to make
sure it is securely in place.
Clean the Ice Storage Bin
Empty the ice container. Use warm water to melt the ice if
necessary.
NOTE: Do not use anything sharp to break up the ice in the
bin. This can cause damage to the ice container and the
dispenser mechanism.
2. Wash ice bin with a mild detergent, rinse well and dry
thoroughly. Do not use harsh or abrasive cleaners or solvents.
16
Remember
• Allow 24 hours to produce the first batch of ice. Allow 3 days
to completely fill ice container.
Avoid connecting the ice maker to a softened water supply.
Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
• Discard the first three batches of ice produced to avoid
impurities that may be flushed out of the system.
• It is normal for the ice cubes to be attached at the corners.
They will break apart easily.
The quality of your ice will be only as good as the quality of •
the water supplied to your ice maker.
For Style I ice maker, do not force the wire shutoff arm up or
down.
Do not store anything on top of the ice maker or in the ice
storage bin.
REFRIGERATOR FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Accessories"
section.
important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble=size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when
removing them to avoid impact from dropping.
Your model may have glass or wire shelves. Store similar foods
together and adjust the shelves to fit different heights. This
reduces the time the refrigerator door is open and saves energy.
Slide-out Shelves (on some models}
To Remove and Replace a Shelf in a Metal Frame:
1. Pull the shelf forward to the stop. Tilt the front of the shelf up
and lift it slightly as you pull the shelf from the frame.
2. Replace the shelf by guiding it back into the slots on the
frame and pushing the shelf in past the stop.
Shelves and Shelf Frames
To Remove and Replace a Shelf/Frame:
1. Remove the shelf/frame by tilting it up at the front and lifting it
out of the shelf supports.
Replace the shelf/frame by guiding the rear shelf hooks into
the shelf supports. Tilt the front of the shelf up until rear shelf
hooks drop into the shelf supports. Check to make sure that
the shelf is securely in position.
_1 __
O
The dell drawer stores raisins, nuts, spreads, and other small
items at normal refrigerator temperatures.
To Remove and Replace the Dell Drawer:
1. Remove the dell drawer by sliding it straight out to the stop.
Lift the front and slide the drawer out the rest of the way.
Replace the dell drawer b sliding it back past the stop.
{<
Crisper and Convertible Vegetable Meat Drawers
To Remove and Replace Drawers:
1. Slide crisper or meat drawer straight out to the stop. Lift the
front of drawer with one hand while supporting the bottom of
drawer with other hand and slide the drawer out the rest of
the way.
2. Replace the crisper or meat drawer by sliding it back in fully
past the drawer stop.
17
Crisper or Vegetable/Meat Drawer Covers
To Remove and Replace Covers:
1. Remove the crisper and meat drawer. Press up in center of
crisper glass insert until it rises above the plastic frame.
Holding the crisper glass firmly, slowly slide the glass insert
forward to remove.
2. Lift crisper cover frame and remove. Repeat steps to remove
the meat drawer cover.
3. Replace back of meat drawer cover frame into supports or
slides on side walls of the refrigerator and lower or slide the
front of the cover frame into place.
4. Slide rear of glass insert into cover frame and lower front into
place. Repeat steps to replace the crisper cover.
The convertible vegetable/meat drawer can be adjusted to
properly chill meats or vegetables. The air inside the pan is
cooled to prevent "spot" freezing and can be set to keep meats
at the National Livestock and Meat Board recommended storage
temperatures of 28° to 32°F (-2°to 0°C).
IMPORTANT: To extend freshness, wrap meats in airtight,
moisture-proof materials before storing. Always store meat as
recommended.
Adjusting the Control
The convertible control comes preset at the lowest meat setting.
To change a control setting: Move the control to the right
(colder) or to the left (less cold) as desired.
To store vegetables: Set the control to VEG (all the way to the
left) to store vegetables at their optimal storage temperatures
(which need to be warmer than those for meat).
IMPORTANT: If food starts to freeze, move the control to the left
(less cold). Remember to wait 24 hours between adjustments.
Doing so gives the temperature of the food time to change.
Meat Storage Guide
Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish ................. use same day as purchased
Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days
Cold cuts, steaks/roasts ........................................... 3-5 days
Cured meats ........................................................... 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.
{
The Crisper Humidity control is located on the crisper cover. You
can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and
HIGH.
LOW (open) lets moist air out of the crisper for best storage of
fruits and vegetables with skins.
• Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.
• Vegetables with skins: Place in plastic bag or plastic
container and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of
fresh, leafy vegetables.
• Leafy vegetables: Wash in cold water, drain and trim or tear
off bruised and discolored areas. Place in plastic bag or
plastic container and store in crisper.
High 5 4 3 2 1 Low
To Remove and Replace the Wine Rack:
1. Remove the rack by pulling it straight out from the shelf.
2. Replace the rack by sliding it in between the shelf and the
wall of the refrigerator.
NOTE: For long-term storage, place eggs in a covered container
or in their original carton on an interior shelf.
FREEZERFEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Accessories"
section.
: ?,
To Remove and Replace the Shelf:
1. Lift the shelf off of the supports.
2. Slide it out of the shelf support holes.
18
3.
Replace shelf in the reverse order.
Frozen Food Storage Guide
Storage times will vary according to the quality and type of food,
the type of packaging or wrap used (should be airtight and
moisture-proof), and the storage temperature. Ice crystals inside
a sealed package are normal. This simply means that moisture in
the food and air inside the package have condensed, creating ice
crystals.
Put no more unfrozen food into the freezer than will freeze within
24 hours (no more than 2 to 3 Ibs. of food per cubic foot
[907 to 1,360 g per 28 L] of freezer space). Leave enough space
in the freezer for air to circulate around packages. Leave enough
room for the door to close tightly.
For more information on preparing food for freezing, check a
freezer guide or reliable cookbook.
The freezer basket or bin can be used to store bags of frozen
fruits and vegetables that may slide off freezer shelves.
To Remove and Replace the Freezer Basket or Bin:
1. Remove basket or bin by sliding it out to the stop.
2. Lift the front of the basket or bin and slide it out the rest of the
way.
{ :
To Remove and Replace the Bin:
1. Remeve the bin by pulling eut on the tabs behind the basket
to release it from the door liner.
2. Replace the bin by aligning the tabs with the buttons on the
sides of the door liner. Firmly snap the tabs onto the buttons
as shown.
The door bin may be removed for easier cleaning.
To Remove and Replace the Bin:
1. Remove the door bin by pushing in slightly on the front of the
bracket while pulling out on the inside tab. Repeat these
steps for the other end of the door bin.
2. Replace the door bin by aligning the ends of the brackets
with the buttons on the sides of the door liner. Firmly snap
bracket and rail assembly onto the tabs above the shelf as
shown.
3. Replace the basket or bin by positioning it on the side wall
guide rails. Lift the basket or bin front slightly while pushing it
past the guide rail stops and slide basket or bin in the rest of
the way.
DOOR FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Accessories"
section.
To Remove and Replace the Rails:
1. Remove the rails by pulling straight up on each end of the rail.
2. Replace the rails by sliding the shelf rail into the slots on the
door and pushing the rail straight down until it stops.
( :
NOTE: Can racks may be purchased as an Accessory for some
models.
19
To Remove and Replace the Racks/Bins:
1. Remove the rack/bin by lifting it and pulling it straight out.
2. Replace the rack/bin by sliding it in above the desired
support and pushing it down until it stops.
The door air control is located on the left-hand side of the
refrigerator compartment.
• Slide the door air control to the left to reduce the flow of cold
air to the bin or can rack and make it less cold.
• Slide the door air control to the right to increase the flow of
cold air to the bin or can rack and make it colder.
REFRIGERATOR CARE
Explosion Hazard
Use nonflammabme cleaner.
Failure to do so can result in death, expmosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to prevent
odors from building up. Wipe up spills immediately.
To Clean Your Refrigerator:
1. Unplug refrigerator or disconnect power.
2. Remove all removable parts from inside, such as shelves,
crispers, etc.
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
• Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.
• To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
4. Determine whether your refrigerator exterior is painted metal,
brushed aluminum or stainless steel and choose the
appropriate cleaning method.
Painted metal: Wash exteriors with a clean sponge or soft
cloth and a mild detergent in warm water. Do not use abrasive
or harsh cleaners, or cleaners designed for stainless steel.
Dry thoroughly with a soft cloth. For additional protection
against damage to painted metal exteriors, apply appliance
wax (or auto paste wax) with a clean, soft cloth. Do not wax
plastic parts.
Brushed aluminum: Wash with a clean sponge or soft cloth
and a mild detergent in warm water. Do not use abrasive or
harsh cleaners, or cleaners designed for stainless steel. Dry
thoroughly with a soft cloth.
Stainless steel finish: Wash with a clean sponge or soft
cloth and a mild detergent in warm water. Do not use abrasive
or harsh cleaners. Dry thoroughly with a soft cloth.
To keep your stainless steel refrigerator looking like new
and to remove minor scuffs or marks, it is suggested that
you use the manufacturer's approved Stainless Steel
Cleaner & Polish. To order the cleaner, see the
"Accessories" section.
IMPORTANT: This cleaner is for stainless steel parts only?
Do not allow the Stainless Steel Cleaner & Polish to come into
contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If accidental contact does
occur, clean plastic part with a sponge and mild detergent in
warm water. Dry thoroughly with a soft cloth.
There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
• Remove the base grille. See "Base Grille" graphic or
"Base Grille" section.
• Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
• Replace the base grille when finished.
Plug in refrigerator or reconnect power.
2O
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
KitchenAid KSRU25CRWH00 Le manuel du propriétaire
- Catégorie
- Frigos
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
KitchenAid KSRB22FRBX00 Le manuel du propriétaire
-
KitchenAid KSRX25FTST02 Le manuel du propriétaire
-
-
KitchenAid KBRS19KTSS01 Le manuel du propriétaire
-
KitchenAid KSRA22ILBL00 Le manuel du propriétaire
-
-
-
KitchenAid KSRG22FKSS19 Le manuel du propriétaire
-
-