KitchenAid KTRS19KMBT00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KTRS19KMBT00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Kitchen_kid _

TOP-MOUNT REFRIGERATOR

For questions about features, operation/performance, par_s accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

P P P

REFRIGERATEUR SUPERPOSE

I'/{ Ii' _I" I, I _ +'

_... ,=.III, ,,, _..i I (,?[ Q Q'III[_!_:[]I@III

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-867-6777 ou visitez notre site web &...

www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 2

2225409

TABLE OF CONTENTS

REFRIGERATOR SAFETY .......................................................... 3

Proper Disposal of Your Old Refrigerator .................................... 3

REFRIGERATOR INSTALLATION ................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Water Supply Connection ............................................................ 5

Refrigerator Doors ....................................................................... 6

Door Closing and Alignment ...................................................... 11

Water System Preparation ......................................................... 11

Normal Sounds .......................................................................... 12

REFRIGERATOR USE .................................................................. 12

Ensuring Proper Air Circulation .................................................. 12

Using the Control(s) .................................................................... 12

Water Dispenser ......................................................................... 13

Interior Water Filtration System ................................................. 13

Ice Maker .................................................................................... 14

REFRIGERATOR FEATURES ...................................................... 15

Refrigerator Shelves ................................................................... 15

Lateral Adjustable Shelf ............................................................. 15

Crispers and Meat Drawers ....................................................... 15

Crisper Humidity Control ........................................................... 16

Chilled Meat Drawer ................................................................... 16

Wine or Can/Bottle Rack ........................................................... 16

Utility or Egg Bin......................................................................... 17

FREEZER FEATURES .................................................................. 17

Freezer Shelf .............................................................................. 17

Adjustable Half-width Freezer Shelf .......................................... 17

Pull-out Freezer Floor ................................................................. 17

DOOR FEATURES ........................................................................ 17

Door Rails ................................................................................... 17

Can Racks and Door Bins .......................................................... 18

Adjustable Utility Compartment & Tray ..................................... 18

Flip-up Door Shelf ...................................................................... 18

REFRIGERATOR CARE ............................................................... 18

Cleaning ...................................................................................... 18

Changing the Light Bulbs ........................................................... 19

Power Interruptions .................................................................... 19

Vacation and Moving Care ......................................................... 19

TROUBLESHOOTING .................................................................. 20

ASSISTANCE OR SERVICE ......................................................... 21

In the U.S.A ................................................................................ 22

In Canada ................................................................................... 22

Accessories ................................................................................ 22

WATER FILTER CERTIFICATIONS ............................................. 22

PRODUCT DATA SHEETS ....................................................... 23

WARRANTY .............................................................................. 24

TABLE DES MATIERES

SI_CURITI_ DU RI_FRIGI_RATEUR ........................................... 25

Mise au rebut de votre vieux refrigerateur ................................. 25

INSTALLATION DU RI_FRIGI_RATEUR ...................................... 26

Deballage .................................................................................... 26

Emplacement d'installation ........................................................ 26

Specifications electriques .......................................................... 27

Raccordement de la canalisation d'eau .................................... 27

Portes du refrigerateur .............................................................. 28

Fermeture et alignement des portes .......................................... 33

Preparation du systeme d'eau ................................................... 34

Sons normaux ............................................................................ 34

UTILISATION DU RI_FRIGI_RATEUR .......................................... 35

Pour s'assurer d'une circulation d'air appropriee ...................... 35

Utilisation des commandes ........................................................ 35

Distributeur d'eau ....................................................................... 36

Systeme de filtration d'eau interieur .......................................... 36

Machine a gla(_ons ..................................................................... 37

CARACTI_RISTIQUES DU RI_FRIGI_RATEUR ........................... 38

Tablettes du refrigGrateur ........................................................... 38

Tablette a reglage lateral ............................................................ 38

Bacs a legumes et tiroirs a viande ............................................. 39

Reglage de I'humidite dans le bac a legumes ........................... 39

Tiroir a viande refrig_r6 ............................................................... 39

Casier a vin ou porte-cannettes/bouteilles ................................ 40

Casier utilitaire ou oeufrier .......................................................... 40

CARACTI_RISTIQUES DU CONGI_LATEUR ............................... 40

Clayette de congelateur ............................................................. 40

Clayette ajustable demi-largeur pour congelateur .................... 40

Plancher de congelateur coulissant ........................................... 41

CARACTI_RISTIQUES DE LA PORTE ......................................... 41

Tringles dans la porte ................................................................. 41

Porte-cannettes et balconnets ................................................... 41

Compartiment utilitaire et plateau reglables .............................. 41

Tablette de porte relevable ........................................................ 42

ENTRETIEN DU RI_FRIGI_RATEUR ............................................ 42

Nettoyage ................................................................................... 42

Remplacement des ampoules d'eclairage ................................ 42

Pannes de courant ..................................................................... 43

Entretien avant les vacances ou Iors d'un demenagement .......43

DI_PANNAGE ................................................................................. 43

ASSISTANCE OU SERVICE ......................................................... 46

Aux letats-Unis ............................................................................ 46

Au Canada .................................................................................. 46

Accessoires ................................................................................ 46

FEUILLES DE DONNI_ES SUR LE PRODUIT .......................... 47

GARANTIE ................................................................................. 48

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance, Always read and obey all

safety messages,

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING," These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord,

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker (on

ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water

(on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your

Old Refrigerator

Before you throw away your old refrigerator or freezer

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

REFRIGERATOR

INSTALLATION

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the "Refrigerator Safety" section.

On some models, shelves, bins, door shelf rails, and other

feature parts may be packaged in the Interior FeaturePak.

Follow the instructions contained in the package for proper

assembly.

Depending on your model, to remove the protective

(transparent) film that is on the nameplate, which is located

on the freezer handle, use your fingernail and peel off the film,

starting from one side and peeling to the other.

IMPORTANT: Do not remove the white foam air return insert that

is located behind the control panel on the ceiling of the

refrigerator (on some models). The insert is part of the refrigerator

and not part of the packing material. If the insert is removed, ice

may migrate down from the freezer and cause icicles to form.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pulI the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

E×pJosion Hazard

Keep flammabJe materiaJs and vapors, such as

gasoline, away from refrigerator.

Failure to do so can resuJt in death, explosion,

or fire.

Toensure proper ventilation for your refrigerator, allow for Y2in.

(1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on

each side (depending on your model) to allow for the door to

swing open. If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

V2"{1.25 era}

II I

Cleaning before use

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

the "Refrigerator Care" section.

_mportant information to know about glass shemves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

EJectricalShockHazard

Plugintoagrounded3prongoutlet.

Donotremovegroundprong.

Donotuseanadapter.

Donotuseanextension cord.

Failure to follow these instructions can result in

death, fire, or eJectricaJ shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection:

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Read all directions carefully before you begin.

IMPORTANT."

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where temperatures will remain above freezing.

Tools required: Standard screwdriver, 7/_ein. and _/_in. open-end

wrenches or two adjustable wrenches, V4in. nut driver and drill

bit, hand drill or electric drill (properly grounded),

NOTE: Your refrigerator dealer has a kit available with a _/4in.

(6.35 ram) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes, Do not use a piercing-type or _/_ein.

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Cold water supply

Connect the ice maker to a cold water line with water pressure

between 30 and 120 psi. Ifyou have questions about your water

pressure, call your utility company.

Connecting to Water Line

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

Locate a _/_in. to V4in. (1.25 cm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of

the pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use V4in.

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

Using a grounded drill, drill a _/4in. hole in the cold water pipe

you have selected.

7 ..................2

1.Cold Water Pipe 5. Compression Sleeve

2. Pipe Clamp 6. Shutoff Valve

3. Copper Tubing 7.PackingNut

4. Compression Nut

Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the _/4in. drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slipthecompressionsleeveandcompressionnutonthe

coppertubingasshown.Inserttheendofthetubingintothe

outletendsquarelyasfarasitwillgo.Screwcompressionnut

ontooutletendwithadjustablewrench.Donotovertighten.

8. Placethefreeendofthetubinginacontainerorsink,and

turnONthemainwatersupply.Flushthetubinguntilwateris

clear.TurnOFFtheshutoffvalveonthewaterpipe.Coilthe

coppertubing.

Connecting to Refrigerator

1. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten. Use the tube clamp on the back of the

refrigerator to secure the tubing to the refrigerator as shown.

This will help prevent damage to the tubing when the

refrigerator is pushed back against the wall.

2. Turn shutoff valve ON.

3. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

4. Valve Inlet

4. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install it

in the 1/4in. (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

5. Plug in refrigerator or reconnect power.

Standard Contour Architect'_

Handle Removal (Architect _ Series)

(Graphics are included later in this section.)

NOTE: These instructions are for the Architect ®Series doors with

curved handle only.

1. Using a 1/8in. Allen wrench, loosen the 2 set screws located

underneath each handle.

2. Pull handle straight out from the door. Make sure you keep

screws for reattaching handles.

Door and Hinge Removal (all models)

IMPORTANT:

• Before you begin, turn the refrigerator control OFF, unplug

refrigerator or disconnect power. Remove food and any

adjustable door or utility bins from doors.

• If you are only removing and replacing the doors, the

instructions are the same regardless of door style.

• If you have a standard or contour door and are also going to

reverse the door swing, follow the instructions for the

appropriate door style.

• All graphics referenced in the following instructions are

included later in this section after "Final Steps."

5/16"Hex-Head Hinge Screw

TOOLS NEEDED: %6 in. hex-head socket wrench, No. 2 Phillips

screwdriver, flat-head screwdriver, %6 in. open-end wrench, flat 2

in. putty knife.

1. Unplug refrigerator or disconnect power.

2. Open refrigerator door and remove base grille from the

bottom front of the refrigerator (see Base Grille graphic).

3. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

4. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

5. Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

6. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

Door Reversal (optional on some models)

IMPORTANT:

• Architect ®Series doors with curved handle are not reversible.

• If you want to reverse your standard or contour doors so they

open from the opposite side, follow these steps. If you are not

reversing the doors, see "Door and Hinge Replacement."

Standard Door

(Graphics are included later in this section.)

Door Stop Screw

Door Handle Sealing Screw

Flat-Head Handle Screw

Door Handle Seal Screw Front

Cabinet

Door Hinge Hole Plug

Cabinet Hinge Hole Plug

Round-Head Handle Screw

Shoulder Handle Screw

1. Remove %6 in. hex-head hinge screws from handle side and

move them to opposite side (see Graphic 1-1).

2. Remove cabinet hinge hole plugs from cabinet top and move

them to opposite side hinge holes as shown (see Graphic

1-2).

Freezer door

1. Remove freezer handle assembly as shown. Keep all parts

together (see Graphic 2).

2. Remove door hinge hole plug. Move to opposite side as

shown (see Graphic 3).

3. Remove door handle sealing screws. Move to opposite side

of freezer door as shown (see Graphic 4).

4. Remove door stop. Move to opposite side of freezer door as

shown (see Graphic 5).

5. Position handle on opposite side of freezer door. Assemble

handles on door as shown (see Graphic 2).

6. Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

Refrigerator door

1. Remove refrigerator handle assembly as shown. Keep all

parts together (see Graphic 6-1).

2. Remove shoulder handle screw from refrigerator door as

shown. Keep all parts together (see Graphic 6-2).

3. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown (see Graphic 3).

4. Remove door handle sealing screws. Move to opposite side

of refrigerator door as shown (see Graphic 4).

5. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown (see Graphic 7).

6. Position shoulder handle screw on opposite side of

refrigerator door and drive screw as shown (see Graphic 6-2).

7. Remove door stop. Moveto opposite side of refrigerator door

as shown (see Graphic 5).

8. Position refrigerator handle on opposite side of the

refrigerator door as shown (see Graphic 6-3). Drive top two

screws in handle first. Align lower portion of handle and drive

bottom screw,

9. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on product,

Contour Door

(Graphics are included later in this section.)

Round-Head Door Handle

Handle Screw Screw Hole Plug

Cabinet

Door Hinge

Hole Plug

1. Remove %6 in. hex-head hinge screws from handle side and

move them to opposite side (see Graphic 1-1).

2. Remove cabinet hinge hole plugs from the cabinet top and

move them to opposite side hinge holes as shown (see

Graphic 1-2).

Doors

1. Remove door hinge hole plug from top of freezer door. Move

to opposite side as shown (see Graphic 2).

2. Remove door stop from both the freezer and refrigerator door

(see Graphic 3).

NOTE: When reversing the door, the freezer handle becomes the

refrigerator door handle and the refrigerator door handle

becomes the freezer handle (see Door Handle Reversal graphic).

3. Remove freezer handle assembly as shown. Keep all parts

together (see Graphic 4).

4. Remove refrigerator handle assembly as shown. Keep all

parts together (see Graphic 5).

5. Rotate and position handle from refrigerator door onto freezer

door and assemble as shown (see Graphic 6).

6. Rotate and position handle from freezer door onto refrigerator

door and assemble as shown (see Graphic 7).

7. Reinstall door stops to opposite side (see Graphic 8).

Door and Hinge Replacement

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten

all screws (see Center Hinge graphic). Replace the freezer

door.

3. Assemble the parts for the top hinge as shown (see Top

Hinge graphic). Do not tighten screws completely.

4. Line up the doors so that the bottom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten all

screws,

Final Steps

1. Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover (see Top Hinge graphic),

2. Replace the base grille (see Base Grille graphic),

3. Plug in refrigerator or reconnect power.

4. Reset the controls (see "Using the Controls" section).

5. Return all removable door parts to doors and food to product,

Standard

Top Hinge

I. Top Hinge Cover

2. _6" Hex-Head Hinge Screws

3. Top Hinge

Center Hinge

1. Center Hinge

2. 5_ex-Head Hinge Screws

Bottom Hinge

i sottomHinge

2, "_lHex-Head Hinge Sore_s

1. Door Hinge Hole Plug

1. Flat-Head Handle Screws

2. Freezer Door Handle

1. Door Handle Sealing Screws

Front View Side View

1.Door Stop Screw 1 2

2. Door Stop

1. Shoulder

Handle Screw

1. Cabinet Hinge Hole Plugs

1. _" Hex-Head Hinge Screws

1 Door Handle

Seal Screw Front

I. Flat-Head

Handle Screw

2. Round-Head

Handle Screw

Contour

| \I_11.....................................................................1

1.5/_ ,,Hex-Head Hinge Screws

oOo

1. Cabinet Hinge Hole Plugs

Top Hinge

1. Top Hinge Cover

2. 5/_6"Hex-Head Hinge Screws

3. Top Hinge

Center Hinge

1. Center Hinge

2. 5/_6" Hex-Head Hinge Screws

Bottom Binge

1.Bottom Hinge

2. _6" Hex-Head Hinge Screws

Door Handle Reversal

Re-installation of Door Stops

_ i 2

1. Door Stop

2. Door Stop Screw

[]

1. Door Hinge Hole Plug

Removal of Door Stops

......... j1_ 4

1. Door Stop

2. Door Stop Screw

Freezer Door

_ 2

1.Door Handle Sealing Screws

2. Door Handle Screw Hole Plugs

Refrigerator Door

T 2 T

1. Door Handle Screw Hole Plugs

2. Door Handle Sealing Screws

Freezer Door

i 1

1. Door Handle Sealing Screws

2, Door Handle Screw Hole Plugs

Refrigerator Door

1. Door Handle Screw Hole Plugs

2. Door Handle Sealing Screws

Architect ®Series

Base Grille

Top Hinge

I. Top Hinge Cover

2. _6" Hex-Head Hinge Screws

3. Top Hinge

Center Hinge

1. Center Hinge

2. 5h_"Hex-Head Hinge Screws

I. Bottom Hinge

2. _8" Hex-Head Hinge Screws

/// _ ///

1. 1/8" set screw

I. 1/_" set screw

Door Closing

Your refrigerator has two front adjustable rollers - one on the right

and one on the left. If your refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the instructions below:

1. Plug into a grounded 3 prong outlet.

2. Move the refrigerator into its final position.

3. Remove the base grille (see "Base Grille" earlier in this

section). The two leveling screws are part of the front roller

assemblies which are at the base of the refrigerator on either

side.

4. Use a screwdriver to adjust the leveling screws. Turn the

leveling screw to the right to raise that side of the refrigerator

or turn the leveling screw to the left to lower that side. It may

take several turns of the leveling screws to adjust the tilt of

the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

5. Open both doors again and check to make sure that they

close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It

may take several more turns, and you should turn both

leveling screws the same amount.

6. Replace the base grille.

Door Alignment

If the space between your doors looks uneven, you can adjust it

using the instructions below:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a s_6in. socket or wrench.

3. Have someone hold the door in place or put a spacer

between the doors while you tighten the top hinge screws.

4. Replace the top hinge cover.

c 0

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Turn off the ice maker by opening the freezer door and lifting

up the wire shutoff arm as shown.

Install the interior water filter cartridge (on some models). The

interior water filter mounting bracket is located in the upper

corner of the fresh food compartment of the refrigerator.

NOTE: Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system.

• Carefully remove the interior water filter cartridge from its

packaging. Remove the red cap from the cartridge.

• Apply the appropriate month sticker to the cartridge as a

reminder to replace the cartridge within six months. Then

apply the "Water Filter Replacement Reminder" sticker to

your calendar.

• Line up the INSTALL mark on the water filter label with the

indicator line that is molded into the filter mounting

bracket cover. Push the cartridge into the filter mounting

bracket. Twist the cartridge _/4turn to the right to lock it

into place. The REMOVE mark should be lined up with the

indicator line located on the front cover.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Inspect the filter system for water leaks. Ifyou see water

leaks, see the "Troubleshooting" section.

5. Turn on the ice maker by opening the freezer door and

lowering the wire shutoff arm as shown. Please refer to the

"Ice Maker" section for further instructions on the operation

of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

NOTE: The ice maker and water dispenser feature of this new

refrigerator may make sounds that your old refrigerator didn't

make. The following describes some of the normal sounds and

what may be making them:

• You may hear a buzzing sound when the water valve

opens to flow water to the dispenser or to fill the ice

maker for each cycle.

• Rattling noises may come from the water line immediately

after dispensing water.

REFRIGERATOR USE

....... I>:uope:AI; :i(

y ........

In order to ensure proper temperatures, you need to permit

airflow between the refrigerator and freezer sections, As shown in

the illustration, cool air enters through the bottom of the freezer

section and moves up. Most of the air then flows through the

freezer section vents and recirculates under the freezer floor. The

rest of the air enters the refrigerator section through the top vent,

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a

popping noise.

• You may hear air being forced over the condenser by the

condenser fan.

• You may hear water running into the drain pan during the

defrost cycle.

Do not block any of these vents with food packages. Ifthe vents

are blocked, airflow will be prevented and temperature and

moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out of food, wrap or cover foods tightly.

For your convenience, your refrigerator control(s) are preset at the

factory. When you first install your refrigerator, make sure that the

control(s) are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to

the word OFF or until the word OFF appears. Your product will

not cool when the refrigerator control is set to OFR

Mid-setting "3"

OFF

IoIDIs@

5 1

NORMAL

Mid-setting "3"

Mid-setting "4"

IMPORTANT:

• Give your refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put food

into the refrigerator.

If you add food before the refrigerator has cooled completely,

your food may spoil. Adjusting the Refrigerator and Freezer

Controls to a higher (colder) than recommended setting will

not cool the compartments any faster.

Adjusting Controls

The mid-setting(s) indicated in the previous section should be

correct for normal household usage. The controls are set

correctly when milk or juice is as cold as you like and when ice

cream is firm.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the

chart below as a guide. On models with two controls, adjust the

refrigerator temperature first. Wait at least 24 hours between

adjustments and then recheck the temperatures.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section too Adjust REFRIGERATOR

warm or TEMPERATURE

• Door opened often, large Control one setting

amount of food added or room higher

temperature very warm

FREEZER section too warm/ice

not made fast enough

• Door opened often, or large

amount of food added or very

cold room temperature (can't

cycle often enough)

Adjust FREEZER or

TEMPERATURE Control

one setting higher

• Heavy ice usage

REFRIGERATOR section

too cold

• Controls not set correctly for

your conditions

Adjust REFRIGERATOR

or TEMPERATURE

Control one setting

lower

FREEZER section too cold Adjust FREEZER or

• Controls not set correctly for TEMPERATURE Control

your conditions one setting lower

,;}[}}¢:!, - +_

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Faiture to do so can result in cuts.

If you did not flush the water system when the refrigerator was

first installed, dispense water into a container until you draw and

discard 2 to 3 gal. (8 to 12 L) orfor approximately 6 to 7 minutes

after the water begins dispensing. The water you draw and

discard rinses the pipes. Allow several hours for the refrigerator

to cool down and chill water.

Dispensing Water

There are two water dispenser buttons as shown for use with

different sizes of containers.

1. Press a glass against the back button or hold a container

under the dispenser while pressing the front button.

2. Remove the glass or release the front button to stop

dispensing.

NOTE: Dispense enough water every week to maintain a fresh

supply.

The water filter status light (on some models)

The water filter status light will help you know when to change

your water filter cartridge. The light is located at the top of the

refrigerator compartment on the control box, The light will change

from green to yellow. This tells you that it is almost time to

change the water filter cartridge (90% of the filter life has been

used). It is recommended that you replace the water filter

cartridge when the water filter indicator light changes to red OR

water flow to your water dispenser or ice maker decreases

noticeably. (See "Replacing the interior water filter cartridge" later

in this section.)

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

............ 2

uu))

1. Water filter status light

2. Refrigerator light switch

After changing the water filter cartridge, reset the water filter

status light by pushing the refrigerator light switch back and forth

5 times within 10 seconds. The status light will change from red

to green when the system is reset.

Non-indicator water filter (on some models)

If your refrigerator does not have the water filter status light, you

should change the water filter cartridge every 6 to 9 months

depending on your usage. Ifthe water flow to the water dispenser

or ice maker decreases noticeably before 6 months have passed,

replace the water filter cartridge more often.

Replacing the interior water filter cartridge

The interior water filter cartridge is located in the upper corner of

the fresh food compartment of the refrigerator.

1. Twist the interior water filter cartridge 1/4turn to the left. The

INSTALL mark will be lined up with the indicator line located

on the filter mounting bracket cover.

2. Gently pull down on the cartridge to remove it from the filter

mounting bracket assembly. To prevent water from spilling

inside the refrigerator, DO NOT TIP the cartridge. Dispose of

the cartridge.

3. Install the new interior water filter cartridge. You can run the

dispenser without a water filter cartridge, but your water will

not be filtered.

• Carefully remove the interior water filter cartridge from its

packaging. Remove the red cap from the cartridge.

• Apply the appropriate month sticker to the cartridge as a

reminder to replace the cartridge within six months. Then

apply the "Water Filter Replacement Reminder" sticker to

your calendar as a reminder to replace the cartridge in six

months.

Line up the INSTALL mark on the water filter label with the

indicator line that is molded into the filter mounting bracket

cover. Push the cartridge into the filter mounting bracket.

Twist the cartridge 1/4turn to the right to lock it into place. The

REMOVE mark should be lined up with the indicator line

located on the front cover.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Inspect the filter system for water leaks. Ifyou see water

leaks, see the "Troubleshooting" section.

Turningthe ice maker on/off

NOTE: Do not force the wire shutoff arm up or down.

• To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

• To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

Increasing ice production rate

NORMAL Ice Production: In Normal ice production mode, the

ice maker should produce approximately 8 to 12 batches of

ice in a 24-hour period. If ice is not being made fast enough,

turn the Freezer Control toward a higher (colder) number in

half number steps. (For example, if the control is at 3, move it

to between 3 and 4.) Wait 24 hours and, if necessary,

gradually turn the Freezer Control to the highest setting,

waiting 24 hours between each increase.

MAXIMUM Ice Production (on some models): In Maximum ice

production, the ice maker should produce approximately 16

to 20 batches of ice in a 24-hour period. If your refrigerator

has the maximum ice production feature, push the switch to

MAX.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATOR

FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

Important information to know about glass shemves

8nd covers:

Do not clean glass shelves or covers with warm water when

they are cold• Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces• This is normal• Glass

shelves and covers are heavy. Use specia! care when re-

moving them to avoid impact from dropping.

Toslide the shelf from side to side, lift up on the front of shelf and

slide to the desired location. Lower shelf to the level position.

NOTE: You do not have to remove small items from the shelf

before moving it from side to side. You may need to remove larger

items.

To remove the shelf:

NOTE: The shelf is heavy and must be removed using both

hands.

1. Hold the back of the shelf with one hand.

2. Lift the front of the shelf with the other hand to a 45° angle

and lower it slightly to release it from the upper channel of the

track. Pull the shelf straight out.

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This

reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models}

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding back into the slots on the

frame and pushing the shelf in )ast the stop.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check to make sure that

the shelf is securely in position.

To remove and replace the shelf track:

1. Remove the shelf track by lifting both sides of the track

slightly and pulling the track straight out.

2. Replace the track by guiding the track hooks into the shelf

support slots on the back wall.

NOTE: Make sure that both sets of track hooks are in the

slots and that the slots are parallel with each other.

3. Push the track back and down securely into the shelf

supports.

To replace the shelf:

NOTE: Make sure that both of the rear shelf slides are securely in

the track before letting go of the shelf. The lateral shelf may be

difficult to install if the track is placed too close to the refrigerator

ceiling. Reposition the track on a lower rung until the shelf can be

tilted enough to easily slide into the track.

1. Hold the shelf at the front and tip the front at a 45 ° angle to

the track.

2. Insert both of the rear shelf slides into the upper channel of

the track, and lower the front of the shelf into place.

Drawers

To remove and replace a drawer:

1. Slide drawer straight out to the stop. Lift the front of the

drawer and slide it out the rest of the way.

2. Replace a drawer by sliding it back in fully past the stop.

CrisperCover

To remove the crisper(s) cover:

1. Remove crisper(s). Hold the glass insert firmly with one hand

and press up in the center of the glass insert until it rises

above the plastic frame. Carefully slide the glass insert

forward to remove.

2. Lift the cover frame and remove it.

To replace the crisper cover:

NOTE: Before reinstalling the cover, make sure the U-shaped

reinforcement bar is reinstalled in the front edge of the crisper

cover.

1. Fit back of cover frame into supports on side walls of the

refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into

place.

Meat Drawer Cover

To remove and replace the meat drawer cover (Style 1

glass):

1. Remove the meat drawer. Tilt up the front of the cover and lift

at the back. Pull the cover straight out.

2. Replace the cover by guiding the rear hooks into the shelf

supports. Tilt the cover up at the front until the rear hooks

drop into the slots. Lower the front of the cover to a level

position and replace the meat drawer.

To remove and replace the meat drawer cover (Style 2

plastic):

1. Remove the meat drawer. Tilt the cover up at the front and

pull it forward and out.

2. Replace the meat drawer cover by fitting the notches and rear

edge of the cover over rear and center crossbars on the shelf.

Lower cover into place and replace the meat drawer.

• Fruit: Wash, let dry and store in refrigerator in plastic bag in

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

Humidity Control Location

• Humidity Control on crisper drawer (Style 1 - on left/Style 2 -

on right)

High 5 4 3 2 1 Low

Slide the meat drawer temperature control forward to make the

meat drawer less cold or backward to make the drawer more

cold.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish .................. use same day as purchased

Chicken, ground beef, variety meats (liver) ............... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ............................................................ 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

You can adjust the amount of humidity in the moisture-sealed

crisper using the settings between HIGH and LOW.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

To remove and replace the wine rack (left) or can/bottle

rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

Depending on your model, you may have a one, two or three

piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long-term storage. If

your model does not have an egg storage bin, store eggs in their

original carton on an interior shelf.

,:_ ..... ........ _.......

To remove and replace the shelf:

1. Remove the shelf by lifting the shelf up and pulling

straight out.

2. Replace the shelf over the supports and lower it into place.

FREEZER FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

To remove and replace the shelf:

1. Remove the shelf by lifting the entire shelf slightly and move it

all the way to one side. Tilt the other side up and out of the

shelf supports.

2. Replace the shelf by inserting one end all the way into the

center of the shelf supports. Then, lower the other end of the

shelf and insert it into the shelf supports.

NOTE: The shelf should lower slightly and lock into place. If the

shelf does not appear stable, make sure both ends of the shelf

are inserted into the shelf supports.

To remove and replace the freezer floor:

1. Lift both back "fences" up and out.

2. Remove the freezer floor by pulling it out about 1 in. (2.5 cm)

with one hand around the air tower section (center back) and

one hand at center front.

3. Lift up floor at rear until hooks release from cabinet and pull

the floor out the rest of the way.

4. Replace the freezer floor by sliding the floor straight in until

the hooks drop into place at rear of cabinet.

5. Replace "fences" by aligning pins with socket in the floor, and

pushing down until they snap into place.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Seal the package

or container securely to prevent taste and odor transfer

throughout the product. Ice crystals inside a sealed package are

normal.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot [907-

1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. The freezer door

must close tightly. For more information on preparing food for

freezing, check a freezer guide or reliable cookbook.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

£_i/_13........ _ : _ _ o _.,._a_

The shelf bottom flips up so you can store taller items in the door

shelf below. When in the down position, the shelf is strong

enough to hold up to 10 Ibs. (4.5 kg).

NOTE: Can racks may be purchased as an Accessory for some

models.

To remove and replace the racks/bins:

1. Remove the rack/bin by lifting it and pulling it straight out.

2. Replace the racWbin by sliding it in above the desired

support and pushing it down until it stops.

((/ __r,Olt4? ..... ,,

The utility compartment and tray slide from one side to the other

for more flexible storage. The tray fits on either side of the utility

compartment or partially underneath it. Try moving it to different

positions to find the option that works best for you.

To install and adjust the utility compartment and tray:

1. Insert the front of the utility tray into the slot on the back of

the shelf rail. Lower the back of the tray into position.

2. Place the front of the utility compartment on top of the shelf

rail. Lower the back of the compartment onto the ribs on the

refrigerator door.

Adjust the utility compartment by lifting the front slightly and

sliding it to the desired position. Lower the front to lock it into

place.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion,

or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

Cleaning your refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to .95 L] of water).

4. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Dry thoroughly with a soft

cloth. For additional protection against damage to painted

metal exteriors, apply appliance wax (or auto paste wax) with

a clean, soft cloth. Do not wax plastic parts.

NOTE: To keep your Stainless Steel refrigerator looking like

new and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel Cleaner

& Polish.

IMPORTANT: This cleaner is for Stainless Steel parts only)

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does

occur, clean plastic part with a sponge and mild detergent in

warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see the "Accessories" section.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every two to

three months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille (see "Base Grille" or "Door

Removal" section).

• Use a vacuum with a soft brush to clean the grille, the

open areas behind the grille and the front surface area of

the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size, shape, and wattage.

1. Unplug refrigerator or disconnect power.

2. Remove the bulb from behind the control panel in the

refrigerator or from behind the light shield in the freezer (on

some models). Replace it with an appliance bulb of the same

wattage.

3. Plug in refrigerator or reconnect power.

If the power will be out for 24 hours or less, keep both refrigerator

doors closed to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen for

two to four days.

• If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

%iI(iii/].I111(_iII:II['ICI ,_ _. ,_I _._ ( _IIC_

Vacations

If you choose to leave the refrigerator on while you're

away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFR See the "Using the Control(s)"

section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFR See the "Using the Control(s)"

section.

5. Unplug the refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See the "Door Closing" or "Leveling Your

Refrigerator" section.

10. Tape the doors shut and the power cord to the refrigerator

cabinet.

When you get to your new home, put everything back and refer to

the "Refrigerator Installation" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power cord unplugged? Plug into a grounded 3 prong

outlet.

• Has a household fuse or circuit breaker tripped? Replace

the fuse or reset the circuit breaker.

• Is the Refrigerator Control turned to the OFF position?

See the "Using the Control(s)" section.

• Is the refrigerator defrosting? Recheck to see if the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

The lights do not work

• Is the power cord unplugged? Plug into a grounded 3 prong

outlet.

• Is a light bulb loose in the socket or burned out? See the

"Changing the Light Bulb(s)" section.

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate. It is

normal for water to drip into the defrost pan.

• Is it more humid than normal? When it is humid, expect that

the water in the defrost pan will take longer to evaporate.

The motor seems to runtoo much

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room

temperatures, your motor will run about 40% to 80% of the

time. Under warmer conditions, it will run even more.

Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the

refrigerator back down.

Are the doors opened often? The motor will run longer

when this occurs. Conserve energy by getting all items out at

one time, keeping food organized, and closing the door as

soon as possible.

• Is the control set correctly for the surrounding

conditions? See the "Using the Control(s)" section.

• Are the doors closed completely? Close the doors firmly. If

they do not close completely, see "The doors will not close

completely" later in this section.

• Are the condenser coils dirty? This prevents air transfer and

makes the motor work harder. Clean the condenser coils. See

the "Cleaning" section.

NOTE: Your new refrigerator will run longer than your old one due

to its high-efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See the

"Normal Sounds" section.

The ice maker is not producing ice or not enough ice.

• Has the ice maker just been installed? Wait 72 hours for full

ice production to begin. Once your refrigerator is cooled, the

ice maker should produce 70-120 cubes every 24 hours.

• Is the freezer temperature cold enough to produce ice?

Wait 24 hours after hook-up for ice production. See the

"Using the Control(s)" section.

• Is the wire shutoff arm in the OFF (arm up) position?

Lower the wire shutoff arm to the ON (arm down) position.

See the "Ice Maker" section.

• Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve. See the "Water Supply

Connection" section.

Does the ice maker mold have water in it or has no ice

been produced? Be sure your refrigerator has been

connected to a water supply and the supply shutoff valve is

turned on. See the "Water Supply Connection" section.

• Is an ice cube jammed in the ejector arm? Remove the ice

from the ejector arm with a plastic utensil. See the "Ice

Maker" section.

• Has a large amount of ice just been removed? Allow 24

hours for ice maker to produce more ice.

• Is the control set correctly? If too little ice is produced, see

the "Using the Control(s)" section.

Is there a water filter installed on the refrigerator? The

filter may be full or incorrectly installed. Depending on your

model, remove the water filter cartridge (see the "Interior

Water Filtration System" section). Operate the dispenser. If

the water flow increases noticeably, your filter is full and

needs to be replaced.

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

Off-taste, odor or gray color in the ice

• Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored too long? Throw old ice

away and make a new supply.

• Has food in the refrigerator been wrapped properly? See

the "Refrigerator Features" section.

• Do the freezer and ice bin need to be cleaned? See the

"Cleaning" section.

• Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator?

Gray or dark discoloration in ice indicates that the water

filtration system needs additional flushing. Run additional

water through the water dispenser to flush the water filtration

system more thoroughly, at least 2 to 3 gal. (8 to 12 L) or 6 to

7 minutes initially. Discard discolored ice.

The water dispenser will not operate properly

Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to

depress the water dispenser until water begins to flow.

Dispense and discard 2 to 3 gal. (8 to 12 L) of water. This will

take approximately 6 to 7 minutes and will help clear air from

the line. Additional flushing may be required in some

households. See the "Water Dispenser" section.

La page est en cours de chargement...

KitchenAid KTRS19KMBT00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KTRS19KMBT00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KTRS19KMBT00 Owner's manual

KitchenAid KTRS19KMBT00 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KTRS19KMBT00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents