Crosley FEQ1452CKS0 Guide d'installation

Marque: Crosley

Modèle: FEQ1452CKS0

Catégorie: Sèche-linge électriques

Taper: Guide d'installation

Ce manuel convient également à

stallati

structi

Instructio

'instal "

www.frigidaire.com P/N 134940500A (0710)

CONTENTS

Pre-lnstallation Requirements .......................................................................................................................................... 2

Electrical Requirements .................................................................................................................................................. 3

Exhaust System Requirements ...................................................................................................................................... 3-4

Gas Supply Requirements ............................................................................................................................................ 4-5

Location of Your Dryer.................................................................................................................................................... 5

Rough-In Dimensions ..................................................................................................................................................... 6

Mobile Home Installation ............................................................................................................................................... 7

Unpacking ................................................................................................................................................................... 7

Reversing Door Swing ................................................................................................................................................. 7-9

Electrical Installation .................................................................................................................................................... 10

Grounding Requirements .............................................................................................................................................. 10

Electrical Connections--3-wire ....................................................................................................................................... 11

Electrical Connections--4-wire ........................................................................................................................................ 11

Gas Connection ............................................................................................................................................................ 12

General Installation ....................................................................................................................................................... 12

Replacement Parts........................................................................................................................................................ 12

Fran_ais .................................................................................................................................. 13-24

SAFETY INSTRUCTIONS

Clothes dryer installation and service must be performed by a qualified installer, service agency or the gas supplier.

install the clothes dryer according to the manufacturer's instructions and local codes.

Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the

dryer is installed correctly and safely. Leave these instructions near the Dryer after installation for future reference.

NOTE: The electrical service to the Dryer must conform with local codes and ordinances and the latest edition of the National

Electrical Code, ANSl/NFPA 70, or in Canada, the Canadian electrical code C22.1 part I.

NOTE: The gas service to the Dryer must conform with local codes and ordinances and the latest edition of the National Fuel

Gas Code ANSI Z223.1, or in Canada, CAN/ACG B149.1-2000

NOTE: The Dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions) for HOME USE

only. This Dryer is not recommended for commercial applications such asrestaurants or beauty salons, etc.

RISI_OF FIRE, Foryour safety the information in this manual must be followed to minimize the risk of fire or

explosion or to prevent property damage, personal injury or loss of life. SAVE THESEINSTRUCTIONS.

Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance.

- WHATTODOIFYOUSMELL GAS

. Do not try to light any appliance.

. Do not touch any electrical switch; do not use any phone in your building.

. Clear the room, building or area of all occupants.

. Immediately call your gassupplier from a neighbor's phone. Follow the gas supplier's instructions.

. If you cannot reach your gas supplier, call the fire department.

Your safety and the safety of others is very important.

We have provided many important safety messages in the Use and Care Guide, Operating Instructions, Installation Instructions

and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you or others. All safety

messageswill be preceded by the safety alert symbol and the word "DANGER" or "WARNING ". Thesewords mean:

_ You can be killed or seriously injured if you don't immediately_ follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the

instructions are not followed.

PRE-INSTALLATION REQUIREMENTS

Tools and Materials Required for Installation:

1. Phillips head screwdriver.

2. Channel-lock adjustable pliers.

3. Carpenter's level.

4. Flat or straight blade screwdriver.

5. Duct tape.

6. Rigid or flexible metal 4 inch (10.2 cm) duct.

7. Vent hood.

8. Pipe thread sealer (Gas).

9. Plastic knife.

ELECTRICAL REQUIREMENTS

i ELECTR/CDryer ]

CIRCUIT-Individual 30 amp. branch circuit fused with 30

amp. time delay fuses or circuit breakers,

Use separately fused circuits for washers and dryers, and DO

NOToperate a washer and a dryer on the same circuit.

POWER SUPPLY- 3 wire or 4-wire, 240 volt, single phase, 60

Hz, Alternating Current.

POWER SUPPLY CORD KIT - The dryer MUST employ a 3-

conductor power supply cord NEMA 10-30 type SRDTrated at

240 volt AC minimum, 30 amp., with 3 open end spade lug

connectors with upturned ends or closed loop connectors and

marked for usewith clothes dryers.

WARNING - Risk of Shock. Appliance grounded to neutral

conductor through a link. Grounding through the neutral link is

prohibited for (1) New branch circuit installations (2) mobile

homes; (3) recreational vehicles; and (4) areaswhere local codes

do not permit grou riding through the neutral, (1) disconnect the

link from the neutral, (2) use grounding terminal or lead to

ground appliance in accordance with local codes and (3) connect

neutral terminal or lead to branch circuit neutral in usualmanner

(if the appliance isto be connected by means of a cord kit, use

4-conductor cord for this purpose). USECOPPERCONDUCTOR

ONLY. The dryer MUST employ a 4-conductor power supply

cord NEMA 14-30 type SRDTor ST(as required) rated at 240

volt AC minimum, 30 amp., with 4 open end spade lug

connectors with upturned ends or closed loop connectors and

marked for use with clothes dryers. See ELECTRICAL

CONNECTIONSFORA 4-WIRE SYSTEM.

(Canada - 4-wire power supply cord is installed on dryer.)

OUTLET RECEPTACLE- NEMA 10-30R receptacle to be located

so the power supply cord isaccessible when the dryer is in the

installed position. (Canada - NEMA 14-30R receptacle.)

NEMA 10-30R NEMA 14-30R

GASDryer

CIRCUIT- Individual 15 amp. branch circuit fused with a 15

amp. maximum time delay fuse or circuit breaker.

POWER SUPPLY- 3 wire, 120 volt single phase, 60 Hz,

Alternating Current.

POWER SUPPLYCORD - The dryer isequipped with a 120

volt 3-wire power cord_

NOTE: Do not under any

circumstances remove

grounding prong from

plug. kk

GROUNDING PRONG

EXHA US T SYS TEM REQ UIREMENTS

Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible

metal duct and approved vent hood which has a swing-out

damper(s) that open when the dryer is in operation. When the

dryer stops, the dampers automatically close to prevent drafts

and the entrance of insects and rodents. Toavoid restricting the

outlet, maintain a minimum of 12 inches (30.5 cm) clearance

between the vent hood and the ground or any other obstruction.

The following are specific requirements for

proper and safe operation of your dryer. Failure to follow

these instructions can create excessive drying times and

fire hazards.

Do not install a clothes dryer with flexible

plastic venting materials. If your present system is made up

of plastic duct or metal foil duct, replace it with a rigid or flexible

metal duct. In Canada and the United States if metal (foil type)

duct is installed, it must be of a specific type identified by the

appliance manufacturer as suitable for use with clothes dryers

and in the United States must also comply with the Outline for

Clothes Dryer Transition Duct, UL standard 2158A. Flexible

venting materials are known to collapse, be easily crushed and

trap lint. These conditions will obstruct clothes dryer airflow and

increase the risk of fire. Ensure the present duct is free of

any lint prior to installing dryer duct.

!!!iiiii_iiii

DO DON'T

Correct Incorrect

ii_i_i:iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiii_

DON'T

Incorrect

- Risk of Fire - A clothes dryer must be

exhausted outdoors. Do not exhaust dryer into a chimney, a

wall, a ceiling, an attic, a crawl space or any concealed space

of a building A clothes dryer produces combustible lint. If the

dryer is not exhausted outdoors, some fine lint will be expelled

into the laundry area. An accumulation of lint in any area of the

home can create a health and fire hazard. The dryer must be

connected to an exhaust outdoors. Regularly inspect the

outdoor exhaust opening and remove any accumulation of lint

around the outdoor exhaust opening and in the surrounding

area.

Do not allow combustible materials (for

example: clothing, draperies/curtains, paper) to come in

contact with exhaust system. The dryer MUST NOT be

exhausted into a chimney, a wall, a ceiling, or any concealed

space of a building which can accumulate lint, resulting in a fire

hazard.

Exceeding the length of duct pipe or

number of elbows allowed in the "MAXIMUM LENGTH"

charts can cause an accumulation of lint in the exhaust system.

Plugging the systemcould create afire hazard, aswell asincrease

drying times.

Do not screen the exhaust ends of the vent

system, nor use any screws, rivets or other fastening means

that extend into the duct and catch lint to assemble the

exhaust system. Lint can become caught in the screen, on the

screwsor rivets, clogging the duct work and creating afire hazard

aswell as increasing drying times. Use an approved vent hood

to terminate the duct outdoors, and sealalljoints with duct tape.

All male duct pipe fittings MUSTbe installed downstream with

the flow of air.

Explosion hazard. Do not install the dryer

where gasoline or other flammables are kept or stored. If

the dryer is installed in a garage, it must be a minimum of 18

inches (45.7 cm) above the floor. Failure to do so can result in

death, explosion, fire or burns.

I. Connect an inclined or digital manometer between the dryer

and the point the exhaust connects to the dryer.

2. Set the dryer timer and temperature to air fluff (cool down)

and start the dryer.

3. Read the measurement on the manometer.

4. The system back pressure MUSTNOTbe higher than 0.75

inches of water column. If the system back pressure is

less than 0.75 inches of water column, the system is

acceptable. If the manometer reading is higher than 0.75

inches of water column, the system is too restrictive and

the installation is unacceptable.

Although vertical orientation of the exhaust system is

acceptable, certain extenuating circumstances could affect

the performance of the dryer:

• Only the rigid metal duct work should be used.

• Venting vertical through a roof may expose the exhaust

systemto down drafts causing an increase in vent restriction.

• Running the exhaust system through an uninsulated area

may cause condensation and faster accumulation of lint.

• Compression or crimping of the exhaust system will cause

an increase in vent restriction.

The exhaust system should be inspected and cleaned a mini-

mum of every 18 months with normal usage. The more the

dryer is used, the more often you should check the exhaust

system and vent hood for proper operation.

MAXIMUM LENGTH

of 4" (10.2 cm) Dia. Rigid Metal Duct

VENT HOOD TYPE

Number (Preferred)

Tur., "4

(10.2 cm) (6.35 cm)

0 60 ft.(l&28 m) 48 ft.(14.63 m)

1 52 ft.(15.84 m_ 40 ft.(12.19 m)

2 44 ft.(13.41 m) 32 ft. (9.75m)

3 32 ft.(9.75 m) 24 ft. (7.31 m)

4 28 ft.(8.53 m) 16ft. (4.87m)

MAXIMUM LENGTH

Number of 4" (10.2 cm) Dia. Flexible Metal Duct

VENT HOOD TYPE

of (Preferred)

-4 4"F "F-

(10.2 cm) (6.35 cm)

0 30ft. (9.14m) 18ft.(5.49m)

1 22 ft. (6.71 m) 14 ft. (4.27 m}

2 14 ft. (4.27 m) 10 ft. (3.05 m)

3 NOT RECOMMENDED

INSTALL MALE FiTTiNGS IN CORRECT DIRECTION

In installations where the exhaust system isnot described in the

charts, the following method must be used to determine if the

exhaust system isacceptable:

EXHAUST DIRECTION

All dryers shipped from the factory are set up for rear exhausting.

However, on electric dryers, exhausting can be to the right or left

side of the cabinet or the bottom of the dryer On gas dryers,

exhausting can be to the right side of the cabinet orthe bottom of

the dryer. Directional exhausting can be accomplished by installing

Exhaust Kit, P/N 131456800, available through your parts

distributor Followthe instructions supplied with the kit

EXHAUST DUCT LOCATING DIMENSIONS

/-SAMEASOTHERSiDE

_"_" ./- 5 7/8"

GAS SUPPLY REQUIREMENTS

Replace copper connecting pipe that is not

plastic-coated. Stainless steel or plastic-coated brass MUST

be used.

1 Installation MUST conform with local codes, or in the absence

of local codes, with the National Fuel GasCode, ANSI Z2231

(latest edition)

2 The gas supply line should be of 1/2 inch (127 cm) pipe

3. If codes allow, flexible metal tubing may be used to connect

your dryer to the gas supply line. The tubing MUST be

constructed of stainless steel or plastic-coated brass.

4 The gas supply line MUSThave an individual shutoff valve

5. A 1/8 inch (0.32 cm) N.P.T.plugged tapping, accessible for test gauge connection, MUST be installed immediately upstream

of the gas supply connection to the dryer.

6. The dryer MUST be disconnected from the gas supply piping system during any pressuretesting of the gassupply piping system

at test pressures in excess of I/2 psig (3.45 kPa).

7. The dryer MUSTbe isolated from the gas supply piping system during any pressure testing of the gas supply piping system

at test pressures equal to or lessthan

1/2 psig (3.45 kPa).

LOCATION OF YOUR DRYER

DO NOT INSTALL YOUR DRYER:

1. In an area exposed to dripping water or outside weather conditions.

2. In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and

ventilation air.

3. On carpet. Floor MUSTbe solid with a maximum slope of I inch (2.54 cm).

INSTALLATION IN RECESSOR CLOSET

1. A dryer installed in a bedroom, bathroom, recessor closet, MUST be exhausted outdoors.

2. No other fuel burning appliance shall be installed in the same closet asthe Gasdryer.

3. Your dryer needs the space around it for proper ventilation.

DO NOT install your dryer in a closet with a sofid door.

4. A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bottom of the door, is required.

Air openings are required to be unobstructed when a door isinstalled. A Iouvered door with equivalent air openings for the full

length of the door isacceptable.

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0(0cm) 0(0cm)

Closet 0 (0 cm) 0 (0 cm) 1 (2.54 cm)

Closet door ventilation required: 2 Iouvered openings each 60 square inches (387 square centimeters) -- 3 inches (7.6 cm) from

bottom and top of door.

This dryer MUST be exhausted outdoors.

5. The following illustrations show minimum clearance dimensions for proper operation in a recessor closet installation.

--,,41_o" (o cm)

0" (0 cm)

,, 0" (0 cm)

1" (2.54 cm) _11 _

II ii

II _11 _

CLOSET DOOR

48.5"

(123.19cm)

Dryer Installation Dimensions

Free=Standing & Under Counter

To clear open door

(72.39cm)

28.5"

Gas supply pipe

on rear of unit

(5. 72cm)

2.25"

5.0" (12.7cm)

Center line height

rear, right, left ;_:!::F;;F

vent

4.375" To side exhausts (11.12cm)

5.875" To base exhaust (14.93cm)

27.25 to front of cabinet (69.22cm)

27.75 to clear knobs (70.49cm)

28.5 to clear door handle (72.39cm)

0 o ,'_,_ #

_ -p

|(6.03cm) ! 13.5"

To rear &

base exhaus

27.0"

(68.58cm)

Electrical supply

on rear of unit

36"

"91.44cm)

(34.29cm)

Stacked Dryer Installation Dimensions

72.00"

(11.12cm) (182.88cm)

4.375"

Side

exhausts

41.00"

(104.14cm)

Center line

height for rear,

right, left vents

28.25" to front of cabinet(71.76cm)

28.75" to clear knobs (73.03cm)

29.5" to clear door handle

49" to clear open door (124.46cm)

(34.29cm) !

13.5"

Gas supply pipe

on rear of unit

T "_i•

38.25"

(97.16cm)

(68.58cm)

27.0"

LU O

MOBILE HOME INSTALLATION

I. DryerMUSTbe exhausted outside (outdoors, not beneath the

mobile home) using metal ducting that will not support

combustion. Metal ducting must be 4 inches (10.16 cm) in

diameter with no obstructions. Rigid metal duct ispreferred.

2. If dryer is exhausted through the floor and area beneath the

mobile home isenclosed, the exhaust systemMUSTterminate

outside the enclosure with the termination securely fastened

to the mobile home structure.

3. When installing a gas dryer into a mobile home, a provision

must be made for outside make up air.This provision isto be

not lessthan twice the area of the dryer exhaust outlet.

4. This dryer MUST be fastened to the floor. Mobile Home

Installation Kit No. 346764 isavailable from your dealer.

5. Refer to pages 2 and 3 for other important venting

requirements.

6. Installation MUST conform to current Manufactured Home

Construction & Safety Standard (which isa FederalRegulation

Title 24 CFR-Part 32-80) or when such standard is not

applicable, with American National Standard for Mobile Homes.

Thedryer isdesigned under ANSIZ21.5.1 or ANSI/

UL2158 - CAN/CSA C22.2 (latest editions) for HOME USEonly.

Correct Incorrect

UNPACKING

1. Using the four shipping carton corner posts(two on each side),

carefully laythe dryer on its left side and remove the foam

shipping base.

To prevent damage, do not use the control

panel as a means to pick up or move the dryer.

2. Return the dryer to an upright position.

REVERSING DOOR SWING

Sofid Door Reversing Instructions:

1. Open door and remove four (4) plugs in the door opening

opposite the hinges. Retain all parts for uses later, unless

otherwise noted. Note: Usecare in removing plugs in not

scratching paint on

REMOVE 4 SCREWS

(ONE FROM EACH

HINGE FIRST)

Begin removing the four (4) screws that attach the hinge

to the front panel. For best results, start by only removing

one screw per hinge. Then only loosen the two remaining

screws while firmly holding door to prevent damage to

hinge, front panel or door. After the remaining screws are

loosened, continue to remove all.

3. Placedoor handle side down on a towel or pad to prevent

any possible scratches to door. Remove all remaining

four (4) screws between hinge and door.

4. Remove four (4) screws on opposite side of door.

5. Separate inner door from outer door byplacing a flat screw

driver or putty knife. Rotate the inner door 180 degree

and reassemble the two door halves.

6. Install four (4) screws securing door halves where hinge

was previously attached.

7. Install four (4) screws securing hinge to door assembly.

8. Remove striker and discard.

9. Remove square plug and reinstall in hole striker was just

removed.

10. Install striker (included in literature bag) into hole square

plug was previously installed.

11.Grasping firmly the top of the door, position the door near

the door opening and align the top hinge hole to the top

hole in the front panel door opening. Once the first screw

is started, attach the second screw to the lower hinge.

Once both screws are tightened, install the remaining

two screws.

12.Install four (4) plugs into the front panel door opening

where hinges were originally installed.

Figure 1

Window Door Reversal Instructions

1.0pen door and remove four (4) plugs in the door opening

opposite the hinges. Retain all parts for uses later, unless

otherwise noted. (Figure 1) Note: Use care in removing plugs

in not scratching paint on the front panel.

Figure 2

Figure 4

5. Remove two (2) door handle screws and two (2) hole plugs

from door. Again taking care not to scratch paint on door.

(Figure 4)

2. Begin removing the four (4) screws that attach the hinge to

the front panel. (Figure 2) For best results, start by only

removing one screw per hinge. Then only loosen the two

remaining screws while firmly holding door to prevent damage

to hinge, front panel or door. After the remaining screws are

loosened, continue to remove all.

Figure 3

Figure 5

6. Pull handle away from door assembley. (Figure 5)

Figure 6

7. Separate the outer door from the inner door assembly with

a putty knife or flat screw driver. (Figure 6)

3. Place door on a towel or pad handle side down to prevent

any possible scratches to door. Remove all remaining four (4)

screws between hinge and door. (Figure 3)

4. Remove four (4) screws from side of door opposite of where

hinge was mounted.

Figure 7

11. Reassemble lens to transition ring with holes to install

handle on right-hand side of door assembly. For proper fit

insure the retention tabs on transition ring are on top of lens

8. Remove lens locating screw. (Figure 7)

Figure 8

9. Disengaging several of the retention tabs and pull lens away

from the transition ring. (Figure 8)

Figure 9

Figure 10

Figure 11

12. Reassemblyouter door to inner door assembly. (Figure 11)

13. Install four (4) screws securing hinge to door assembly in

the new location, take note to place hinge in correct

orientation.

14. Install four (4) screws into holes that had secured the

hinge.

15. Remove striker and discard.

16. Remove square plug and reinstall in hole striker was just

removed.

17. Install striker (included in literature bag) into hole square

plug was previously installed.

10. Remove two (2) transition ring plugs and reinstall on

previous handle side. (Figures 9 and 10)

Figure 12

18. Reinstall door handle by placing the handle mounting

bossesthrough holes in lens and transition ring and installing

screws through inner door and tighten into handle bosses.

(Figure 12).

19. Grasping firmly the top of the door, position the door near

the door opening and align the top hinge hole to the top hole

in the front panel door opening. Once the first screw isstarted,

attach the second screw to the lower hinge. Once both screws

are tightened, install the remaining two screws.

20. Install four (4) plugs into the front panel door opening

where hinges were originally installed.

ELECTRICAL INSTALLATION

I ELECTRICDryer

The following are specific requirements for

proper and safe electrical installation of your dryer. Failure

to follow these instructions can create electrical shock and/

or a fire hazard.

This appliance MUST be properly grounded.

Electrical shock can result if tile dryer is not properly grounded.

Follow the instructions in this manual for proper grounding.

Do not use an extension cord with this dryer.

Someextension cords are not designed to withstand the amounts

of electrical current this dryer utilizes and can melt, creating

electrical shock and/or fire hazard. Locate the dryer within reach

of the receptacle for the length power cord to be purchased,

allowing some slack in the cord. Refer to the pre-installation

requirements in this manual for the proper power cord to be

purchased.

A U.L. approvedstrain reliefmustbe installed

onto power cord. If tile strain relief is not attached, tile cord

can be pulled out of the dryer and can be cut by any movement

of the cord, resulting in electrical shock.

Do not use an aluminum wired receptacle

with a copper wired power cord and plug (or vice versa).

A chemical reaction occurs between copper and aluminum and

can cause electrical shorts. The proper wiring and receptacle

is a copper wired power cord with a copper wired

receptacle.

NOTE: Dryersoperating on 208 volt power supplywill have longer

drying times than operating on 240 volt power supply.

j Canadian ELECTR/CDryer J

_ Improper connection of tile equipment grounding

conductor can result in a risk of electrical shock. Check with a

licensedelectrician ifyou arein doubt asto whether the appliance

isproperly grounded.

Fora arounded, cord-connected dryer:

1. The dryer must be grounded. Inthe event of a malfunction or

breakdown, grounding will reduce the risk of electrical shock

by a path of least resistance for electrical current.

Sinceyour dryer isequipped with a power supply cord having

an equipment-grounding conductor and a grounding plug,

the plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances. If in doubt, call a licensed electrician.

Do not modify plug provided with the appliance.

ALL GAS Dryers

1. The dryer is equipped with a three-prong (grounding) plug

for your protection against shock hazard and should be

plugged directly into a properly grounded three-prong

receptacle. Do not cut or remove the grounding prong from

the plug.

GROUNDING REQUIREMENTS

USA ELECTR/CDryer i

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check with a

licensedelectrician ifyou are in doubt asto whether the appliance

isproperly grounded.

For a grounded, cord-connected dryer:

I. Tile dryerMUSTbe grounded. Inthe event of a malfunction

or breakdown, grounding will reducethe riskof electricalshock

by a path of least resistance for electrical current.

2. If your dryer isequipped with a power supply cord having an

equipment-grounding conductor and a grounding plug, the

plug MUST be plugged into an appropriate, copper wired

receptacle that is properly installed and grounded in

accordance with all local codes and ordinances. If in doubt,

call a licensed electrician. Do not modify plug provided

with the appliance.

For a permanently connected dryer:

I. ThedryerMUSTbe connected to a grounded metal, permanent

wiring system; or an equipment grounding conductor must be

run with the circuit conductors and connected to the

equipment-grounding terminal or lead on the appliance.

ELECTRICALCONNECTIONS ELECTRICALCONNECTIONS FOR 4- WIRE SYSTEM

FOR 3- WIRESYSTEM

USA ELECTRICDryer

1. Remove the screws securing the terminal block access

cover and the strain relief mounting bracket located on the

back of the dryer upper corner.

2. Install a U.L approved strain relief into the power cord

entry hole of the mounting bracket. Finger tighten the nut

only at this time.

GREEN

SCREW

NEUTRAL

GROUND

WIRE

SILVER

TERMINAL

USA ELECTR/CDryer

1. Remove the screws securing the terminal block accesscover

and the strain relief mounting bracket located on the back of

the dryer upper corner.

2. Install a U.L approved strain relief in the entry hole of the

mounting bracket. Fingertighten the nut only at this time.

3. Remove the ground wire from the green ground screw

located above the terminal block.

GREEN POWER CORD

GREEN

SILVERTERMINAL

SCREW TERMINAL

BLOCK

tUTTIGHTEN NUT

TO THESE

_READS

BRACKET POWER CORD

3. Thread a U.L approved 30 amp. power cord, NEMA 10-30

type SRDT,through the strain relief.

4. Attach the power cord neutral (center wire) conductor to

the silver colored center terminal on the terminal block.

Tighten the screw securely.

5. Attach the remaining two power cord outer conductors to

the outer brasscolored terminals on the terminal block.

Tighten both screws securely.

Do not make a sharp bend or crimp wiring/

conductor at connections.

6. Reattach the strain relief mounting bracket to the back of

the dryer with two screws. Tighten screws securely.

7. Tighten the screws securing the cord restraint firmly against

the power cord.

8. Tighten the strain relief nut securely sothat the strain relief

does not turn.

9. Reinstall the terminal block cover.

TIGHTEN

NUT

GROUND WHITE TO THESE

WIRE NUT -HREADS

STRAIN

RELIEF

BRACKET,.

POWER

CORD

4. Thread a U.L approved 30 amp power cord, NEMA 14-30

type STor SRDTthrough the strain relief.

TYPICAL 4

TYPICAL 4 BLACK

C_WHITE

_,_I_ED

30 AMP NEMA 14-30 TYPE SRDT OR ST _GREEN

Attach the green power cord ground wire to the cabinet with

the green ground screw.

Attach the white (neutral) power cord conductor from the

power cord and the neutral ground wire from the dryer harness

to the silver-colored center terminal on the terminal block.

Tighten the screw securely.

7. Attach the red and black power cord conductors to the outer

brass-colored terminals on the terminal block.

Do not make a sharp bend or crimp wiring/

conductor at the connections.

Tighten the screws securing the cord restraint firmly against

the power cord.

9. Tighten the strain relief nut securely so the strain relief does

not turn.

10.Reinstall the terminal block accesscover.

11 Printed in U.S.A.

GAS CONNECTION

1. Remove the shipping cap from gas pipe at the rear of the

dryer.

NOTE: DO NOT connect the dryer to L.P. gas service

without converting the gas valve. An L.R conversion kit

must be installed by a qualified gas technician.

2. Connect a I/2 inch (1.27 cm) I.D. semi-rigid or approved

pipe from gas supply line to the 3/8 inch (0.96 cm) pipe

located on the back of the dryer (seepages 6 and 7). Usea

1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for a

connection. Apply an approved thread sealerthat isresistant

to the corrosive action of liquefied gases on all pipe

connections.

3. Open the shutoff valve in the gassupply line to allow gasto

flowthrough pipe.

4. Testall connections by brushing on a soapy water solution.

VALVE OPEN I

GAS FLOW POSITION

NEVER test for gas leaks with an open flame.

GENERAL iNSTALLATiON

I. Connect the exhaust duct to outside exhaust system (see

pages 3 and 4). Use duct tape to seal all joints.

2. With the dryer in its final position, adjust one or more of the

legs until the dryer is resting solid on all four legs. Placea

level on top of the dryer. The dryer MUST be level and

resting solid on all four legs.

3. Plug the power cord into a grounded outlet. NOTE: Check

to ensure the power is off at circuit breakedfuse box before

plugging the power cord into the outlet.

4. Turn on the power at the circuit breaker/fuse box.

Before operating the dryer, make sure the

dryer area is clear and free from combustible materials,

gasoline, and other flammable vapors. Also see that

nothing (such as boxes, clothing, etc.) obstructs the flow

of combustion and ventilation air.

7. Place these instructions in a location near the dryer for

future reference.

NOTE: A wiring diagram is located inside the dryer console

or under the top panel.

8. To stack your dryer on a compatible washer, visit web site

www.frigidaire.com, call your local dealer or call the Toll

Freenutuber (1- 8o0- 444- 4944)to find your localdistributor

to purchase stacking kit accessory part number STACKIT2.

REPLACEMENT PARTS

Pedestal

A pedestal accessory, Model No, NLPWD15 (White),

NLPWD15GB (Glacier Blue), NLPWD15P (Platinum) and

NLPWD15E (Black), specifically designed for this dryer may be

used when elevating the dryer for ease of use. Failure to use

accessoriescertified bythe manufacturer could result in personal

injury, property damage or damage to the dryer.

If replacements parts are needed for your dryer, contact the

source where you purchased your dryer, call 1-800-944-9044,

or visit our website, www.frigidaire.com, for the Frigidaire

Company Authorized Parts Distributor nearest you.

Labelall wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

Destroy the carton and plastic bagsafter the dryer

isunpacked. Children might usethem for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight

chambers causing suffocation. Placeall materials in a garbage

container or make materials inaccessible to children.

The instructions in this manual and all other

literature included with this dryer are not meant to cover every

possible condition and situation that may occur. Good safe

practice and caution MUSTbe applied when installing, operating

and maintaining any appliance.

5. Run the dryer through a cycle check for proper operation.

NOTE: On gas dryers, before the burner will light, it is

necessary for the gas line to be bled of air. If the burner does

not light within 45 seconds the first time the dryer isturned on,

the safety switch will shut the burner off. If this happens, turn

the timer to "OFF" and wait 5 minutes before making another

attempt to light.

6. If your dryer does not operate, please review the "Avoid

Service Checklist" located in your Use and Care Guide be-

fore calling for service.

Table des mati res

Avant I'installation ............................................................................................................................................................ 13

Installation dectrique .................................................................................................................................................... 14

Evacuation de I'air.................................................................................................................................................. 14-I 5

Alimentation en gaz......................................................................................................................................................... 16

Emplacement de la secheuse........................................................................................................................................... 16

Dimensions de I'emplacement ................................................................................................................................. 17

Installation dans une maison mobile .................................................................................................................................. 18

D_ballage ..................................................................................................................................................... 18

Porte R6versible ............................................................................................................................................... 18-20

Installation electrique ....................................................................................................................................................... 21

Mise a la terre ................................................................................................................................................................ 21

Branchement 61ectrique - Installation a 3 fils ........................................................................................................................ 22

Branchement 61ectrique - Installation a 4 ills ........................................................................................................................ 22

Installation .......................................................................................................................................................... 23

Pi6ces de rechange ......................................................................................................................................................... 23

Mesures de S curit Importantes

L'installation et /e service de/a Secheuse de v_tements doivent @treeffectues par un installateur qualifi_, I'agence de

service ou le fournisseur de gaz. Installez la Secheuse de v@tement selon les instructions du fabricant et les codes Iocaux.

Avant de commencer, lire attentivement le present document. Cela simplifiera I'installation et assurera la pose

correcte et securitaire de la s_cheuse. Apres I'installation, laisser ce document _ proximite de la secheuse pour r_ference

future.

REMARQUE :L'alimentation dectrique de lasecheusedoit respecter lescodes et ordonnances Iocaux ainsique 1'6dition laplus r6cente

du Code ANSI/NEPA70, ou au Canada, le Code canadien d'_lectricit_, ACNOR C22. I, partiel.

REMARQUE : L'alimentation en gaz de la s_cheusedoit respecter lescodes et ordon nances Iocaux ainsique 1'6dition laplus r6cente du

Code ANSIZ223. I, ou au Canada, le code CAN/ACG B149.1-2000.

REMARQUE : Las_cheuse est conc;ueconformement au code ANSI Z21.5.1 ou ANSI/UL 2158 - CAN/ACG C22.2 No. 112 (l'_dition la

plus r6cente) pour un USAGEDOMESTIQUEseulement. Cette secheuse n'est pasrecommand6e pour utilisation commerciale, comme

par exemple un restaurant ou un salon de coiffure, etc.

Votre s curit et celle des autres est tr s importante.

Nous donnons de nombreux messagesde s_curite irnportants dans cemanuel et survotre appareil menager. Assurez-vous de toujours

lire tous les messagesde s_curite et de vous y conformer.

Voici le symbole de raiseen garde. Ce symbole met en garde contre lesrisques pouvant entra;ner le d6c6s ou des blessures

soi ou auxautres. Tousles messages relatifs _ la s_curit_ sont pr6c6d6s du symbole de raise en garde et du terme <<DANGER

>>ou <<AVERTISSEMENT>>.Ces termes signifient •

L'utilisateur sera tue gravement bless6 s'il ne suit pas ces directives.

_ L'utilisateur peut 6tre tu6 ou gravement bless6 s'il ne suit pas ces directives.

Tous les messages relatifs _ la securit_ indiquent le risque, comment r_duire le risque de blessure et ce qui peut

survenir si on ne suit pas les directives.

RISQUE D'INCENDIE. Pour votre s_curit_, suivre lesdirectives _nonc_es dans le present guide afin de minimiser

les risques d'incendie, d'explosion, de dommages materiels, de blessures et de mort. GARDEZCES INSTRUCTIONS.

- Ne pasentreposer ni utiliser d'essence ou autres liquides ou produits inflammables _ proximit_ de cette s_cheuse ou de tout

autre appareil m_nager.

- QUE FAIRE S'IL YA UNE ODEUR DE GAZ

• Ne mettre en marche aucun appareil .

Ne toucher aucun interrupteur @lectrique; n'utiliser aucun t@l@phonedans I'immeuble.

Faire sortir tousles occupants de la piece, de I'immeuble ou de la zone avoisinante.

Appeler la fournisseur de gaz immediatement en utilisant le telephone d'un voisin. Suivre les directives du fournisseur de

gaz.

S'il est impossible de joindre le fournisseur de gaz, appeler le service de protection des incendies.

L'installation et les r@parationsdoivent 6tre effectu@espar un service de r@paration, un technicien qualifi@ou le fournisseur de gaz.

AVANT L NSTALLATION

Outils et materiel requis pour I'installation :

I. Tournevisa pointecruciforme

2. Pincemultiprise

3. Niveau demenuisier

4. Tournevis _ pointe plate oua lame droite

5. Rubanadhesifpourconduits

6. Conduite en m_tal rigide ou souple de 10,2 cm (4 po)

7. Bouche d-_vacuation d'air

8. Ruban ou p_te d'@tancheit_ porjoints filetes (modUle a gaz)

9. Couteau a masticen plastique

INSTALLATION ELECTRIQUE

i SecheusesE'ZECTRIOUES ]

CIRCUIT- Derivation distincte de 30 A avecfusibles a retardement

ou disjoncteurs d'au 30 A.

Utilisez des circuits avec un disjoncteur ou fusible s6par6 pour les

machines a laver et s6cheuses, et NE PASfaire fonctionner une

machine a laver et une s6cheuse sur un m6mecircuit.

ALIMENTATIONELECTRIQUE- 3 fils,240 volts, une phase,60 Hz,

courant alternatif. (Canada -240 volts, une phase, 60 Hz, courant

alternatif.)

CORDON D'ALIMENTATION ELECTRIQUE-LasecheuseDOIT6tre

reli_ea un cordon d'alimentation dectrique a3 conducteurs NEMA

10-30 detype SRDTd'u ne capacite minimale de 240 volts, courant

alternatif, 30 A, avec fiche en L a 3 broches pleines ou repli_es

conc_ue pour le branchement d'une secheuse.

AVERTISSEMENT-Risque de choc _lectrique. Unappareil mis

a la terrea I'aide d'un lien ou c_bleconducteur neutre. La mise a

la terre a I'aide d'u n conducteur ou cable neutre est interdite darts

lescas suivants : (1) les installations de nouveau circuit d_vir_ (2)

lesmaisons mobiles (3) lesv_hicules r_cr_atifs ou caravanes et (4)

lesr_gions o0 lescodes Iocaux interdisent la mise a la terre a I'aide

d'un cable ou conducteur neutre. (1) D_branchez le conducteur

ou cabledu neutre, (2)utilisez laborne de misea laterre ou lecable

de mise a laterre de I'appareil conform_ment auxcodes Iocaux et

(3) connectez ou branchez la borne neutre ou lec_ble au neutre du

circuit d_vir_de lamani_re habituelle(si I'appareil doit 6treconnect6

a I'aide d'un cordon, utilisez un cordon a 4 cables ou fils pour ce

faire). N'UTILISEZQUEDESCABLESOUFILSENCUIVRE.

Elle DOlT 6tre reli@ea un cordon d'alimentation @lectrique a

4 conducteurs NEMA 14-30 de type SRDTou ST(au besoin) d'une

capacite minimale de 240 volts, courant alternatif, 30 A, avecfiche

en La 4 broches pleines ou repli6es conc;uepour le branchement

d'une s@cheuse. Se reporter a la section BRANCHEMENT

ELECTRIQUED'UNE INSTALLATIONA 4 FILS.

(Canada - Cordon d'alimentation a4 fils branch@a la s@cheuse.

PRISE- Prise NEMA 10-30R situ@ede fat;on ace que le cordon

d'alimentation @lectriquesoit accessible une fois las_cheuse en

place. (Canada - prise NEMA de 14-30R.)

ALIMENTATIONI I , ^ .

ELECTRIQUE [_;-_ "_BOITE A FUSIBLES PRINCIPALE NEUTRE A 3

I _ FILS 120-2.40 VOLTS 60 CYCLES

I,_,J,_'_ FUSISLESARETARDEMENTOU

_DISJONCTEUR DE 30 A

_ FILNEUTRE

PRISE MURALE

(CUlVRE)

SOUS RESERVE DES EMA 10-30R (CUIVRE)

EXIGENGES LOCALES

CIRCUIT- Derivation distincte de 15 A avecfusible a retardement

ou disjoncteur d'au plus 15 A.

ALIMENTATION¢LLECTRIQUE- 3 fils, 120volts, une phase,60 Hz,

courant altem atif.

CORDON D'ALIMENTATION ELECTRIQUE - La s_cheuse est

pourvue d'un cordon d'alimentation _lectrique a3 fils de 120 volts,

REMARQUE : II ne faut { _J _l] _

broche de mise a la I \ %

\ ( j B,ROCHE DE M!SE

_ A LA TERRE

L'VA CUAT!ON DE L'AIR

Utiliser uniquement une conduite en m_tal rigide ou flexible de

10,2 cm (4 po) de diam_tre (minimu m)ainsi qu'u ne grille de sortie

approuv_e pourvue de clapets qui s'ouvrent Iorsque la s_cheuse

fonctionne. Quand la s_cheuse s'arr6te, les clapets se ferment

automatiquement pour _viter lescourantsd'air etI'entr_e d'insectes

ou de rongeu rs.Afin de ne pasobstruer I'_vacuation deI'air, laisser

une distance minimum de 30,5 cm (12 po) entre la grille de sortie

et le sol ou tout autre obstacle.

Les mises en garde quisuiventse rapportent

directement au fonctionnement correct et securitaire de la

secheuse. Toute derogation a ces mises en garde pourrait

ralentir le s_chage et entrainer des risques d'incendie.

__N'installez pas la Secheuse avec des materiels de

ventilation en rnati#res plastiques flexibles.

Silaconduite existante est en plastique ou en papier metallique, la

_par une conduite en m_tal rigide ou flexible. Au Canada

etaux Etats-Unissileconduit estde m_tal (type feuille d'aluminium),

celui-ci doit _tre d'un type sp_cifique identifi_ par lefabricant,

recommand_ pour I'utilisation avec des S_cheuses; et aux Etats-

Unis il doit en outre remplir la norme UL215% Lesmat_riaux de

ventilation flexibles peuvent s'abimer facilement et recueillir du

duvet. Cesconditions obstrueront lacirculation d'air de laSecheuse

de v_tements et augmenteront lerisque d'incendie. S'assurer

qu'il n'y a pas de charpie clans la conduite existante avant

d'installer la conduite de la s_cheuse.

_- Risque d'incendie- une S_cheuse de v_tement dolt _tre

aere & I'air libre, N'a_rez pas la Secheuse dans une chemin_e,

une paroi, un plafond, un espaceferm_ ou aucun espace cach_ du

batiment. Une secheusea linge produit de lacharpie combustible.

SiFairn'_taitpasrepousseal'ext_rieurdelamaison de petites

particules de charpie seretrouveraient dans lapiece o0 est install_e

la secheuse. Toute accumulation de charpie dans la maison peut

presenter desrisques pour la sant_ et desrisques d'incendie.

NON

Correct Incorrect

OUI

Correct

La s_cheuse dolt _tre connectee a une bouche d'_vacuation

vers I'exterieur du b_timent ou de I'immeuble. Vous devez

inspecter r_guli_rement I'_vent exterieur et enlever toute

accumulation de charpie autour de I'_vent et dans la cavite du

conduit d'_vacuation.

ONe laisseraucun mat_riau inflammable (comme desv6tements,

destentures, des rideaux ou du papier) entrer en contact avec les

conduits d'@acuation.

_ Auqmenter laIonqueur du conduit riqideou lenombrede coudes

permis au tableau _LONGUEURMAXIMUM_> risque de r_duire la

capacite d'_vacuation du circuit. Obturer le circuit peut crier un

risque d'incendie et augmenter letemps de s_chage.

P._q N'obstruez paslesextr_mites du tube de ventilation, niutilisez

desvis, rivets ou autres movens de fixation qui peuvent obstruer le

conduitetrecueillirdu duvet. L'engorgementsubs_quentrisquerait

de ralentir letemps des_chage,voire decauser un incendie. Installer

une bouche d'_vacuation approuv_e a I'ext_rieur et sceller tousles

joints _ I'aide d'un ruban adh_sif a conduits. Tousles raccords de

conduit males DO/VENT_tre install_s dans lesensde la circulation

d'air.

Risques d'explosion, Ne pas installer la

s_cheuse_un endroit o0 I'ongardedelagazolineou tout autreproduit

inflammable. Si las_cheuse est install_e dans un garage, elle dolt

6tre_ un minimum de45,7 cm (18 po)au-dessusdu plancher.Toute

d_rogation pourrait provoquer la mort, I'explosion, I'encendie ou

lesbr01ures.

Nombre de

coudes ,_

90°

Nornbre de

coudes a

90°

LONGUEUR MAXIMUM

d'une conduite en m_tal rigide de

10,16 cm (4 po) de diam.

TYPEDE GRILLEDE SORTIE

(Recommand_)

!4 po)

18,28m

15,84m

13,41m

9,75 m

8,53 m

volet

(60 po) 14,63 rr

(52 po)

(44 po)

(32 po)

(28 po)

(48 po)

12,19 m(40 po)

9,75 m (32 po)

7,31 m (24 po)

4,87 m (16 po)

LONGUEUR MAXIMUM

d'une conduite en metal flexible de

10_16 cm (4 po) de diam.

TYPEDE GRILLEDE SORTIE

{Recommande)

a volet

9,14 m (30 po)

6,71 m (22 po)

4,27 m (14 po)

5,49 m(18 po)

4,27 m (14 po)

3,05 m (10 po)

NON RECOMMANDE

POSERLESRACCORDSMALES DANS LA BONNE DIRECTION

Pour lesinstallations dont lecircuit d'evacuation n'est pasd6crit

dans lestableaux, il faut utiliser la m6thode suivante sile circuit

d'@acuation n'est pas acceptable:

I. Brancher un manom6tre digital ou a tube inclin6 entre la

s6cheuseet le raccord d'6vacuation de la secheuse.

2. Regler la minuterie de la s6cheuse et latemp6rature aair froid

(refroidissement) et d6marrez la secheuse.

3. Lire la mesure indiquee au manometre.

4. La bassepression ne dolt pas6tre sup6rieure a 0,75 pouce de

colonne d'eau. Sila bassepression est inf6rieure a 0,75 pouce

de colon ned'eau, lecircuit est acceptable. Sila lecture indique

une pression sup6rieure a 0,75 pouce de colonne d'eau, la

capacit6 du circuit est insuffisante et I'installation inacceptable.

Bien qu'un circuit vertical soit acceptable, certaines circonstances

attenuantes peuvent influencer la performance de la s6cheuse.

• Ilfaututiliseruniquementdesconduitsrigidesen m6tal.

• Unesortie sur un toit d'un circuit vertical peut exposer celui-ci a

un contre-tirage et ainsi r6duire sacapacite d'@acuation.

• L'isolant que dolt traverser un tel circuit peut causer de la

condensation et ainsir6duire lacapacite d'@acuation du circuit.

• Un circuit d'6vacuation comprim6 ou ondulant peut voir sa

capacite d'@acuation r6duite.

II faut inspecter le circuit d'@acuation et le nettoyer au moins

tousles 18mois d'utilisation normale. Pluslas6cheuseest utilis6e,

plus il faut proceder souvent a une v6rification du bon

fonctionnement du circuit d'@acuation etdu couvercle du registre

ou de I'6vent.

DiRECTiON DEL'EVA CUATION D'AIR

Touteslessecheusesempaquet6es par I'usinesont concuesde fac_on

ce que 1'6vacuation d'air se fasse a I'arri6re. Toutefois, dans le

cas des s6cheuses61ectriques, I'@acuation d'air peut sefaire sur

la droite ou sur la gauche du boitier ou encore, sous la s6cheuse.

Dans le casdess6cheuses _gaz, 1'6vacuation d'air peut sefaire sur

la droite du boitier ou sous la s6cheuse. On peut donc modifier

I'orientationdel'6vacuation d'airen installantun ensemble

d'@acuation d'air n° de pi6ce 131456800 disponible chez d'un

fournisseur de pi6cesagr66. Suivrelesdirectives qui accompagnent

cet ensemble.

EMPLACEMENT DESBOUCHESD'EVACUATIC)N

COMME SUR L'AUTRE COTE

J_,-" 5cm

_' ._(5 7/8 po)

34 crn

11 cm

9,5 cm

(3 3/4 po)

9,5 cm

(3 3/4 po)

ALIMENTAT!ON EN GAZ

Remplacer le tuyau de

raccordement en cuivre non recouvert de

plastique. II FAUT utiliser du laiton

inoxydable ou recouvert de plastique.

1. I_'installationDOITrespecter lescodes Iocaux,

ou s'il n'existe pas de codes Iocaux, le code

ANSIZ223. I (l'edition la plus recente) ou au

Canada, le Code actuel CAN/CGA B149.

2. La conduite d'alimentation en gaz dolt

mesurer 1,27 cm (1/2 po).

3. Silescodes le permettent, un tuyau en m_tal

flexible peut Ctre utilis_ pour connecter la

s_cheuse a I'alimentation en gaz. Le tuyau

DOIT6tre fabriqu_ en acierinoxydable ou en

cuivre avec un rev6tement de plastique.

4. La conduite d'alimentation en gaz DOlT

comporter unrobinet d'arr_t distinct.

5. Uneprisede0,32 cm(1/8 po)NPTaccessible

pour lebranchement d'un manom_treDOIT

Ctre install_e toutjuste en amont du

branchement de la conduite d'alimentation

en gaz sur la s_cheuse.

6. La s6cheuse DOlT Ctre debranchee de la

canalisation degaz pendanttoutev6rification

de pression de I'alimentation en gaz a des

pressionsqui d@assent3,45 kPa(1/2 Ib/po2).

7. La secheuse DOlT 6tre isol6e de la

canalisation degaz pendanttoutev6rification

de pression de I'alimentation en gaz a des

pressions_galesou inf_rieures _3,45 kPa(1/

2 Ib/po2).

EMPLA CEMENT DE LA SECHEUSE

NEPASINSTALLERLA SECHEUSE:

1. Dansunendroitexpos6aun6coulementd'eauouaux conditions

atmospl%riques.

2. Dansun endroit o0 elle serait en contact avecdesrideaux, draperies ou tout cequi

obstruera leflux d'air de combustion et de ventilation.

3. Sur un tapis. Leplancher DOIT6tre ferme et pr6senter une pente de2,54 cm

(1 po) au maximum.

INSTALLATION DANS UNEALCO VEOU UN PLACARD

I. Toute secheuse install6e dans une chambre a coucher, une

sallede bain,une alc6veou un placardDOITCtrereli6ea uneconduite d'6vacuation

d'air seterminant a I'ext_rieur de la maison.

2. Aucun autre appareil br01ant du combustible ne dolt 6tre

install_ dans le m_me placard que la s_cheuse au Gaz.

3. Lasecbeuseabesoin d'un d6gagement suffisant pour permettre lacirculation de

I'air.

NEPASINSTALLERLA SECHEUSEDANS UN PLACARD POURVU D'UNEPORTE

PLEINE.

4. Uneouverture rainirnumde 774,2 cm2(120 po2)r@artie 6galement entre lehaut

et le hasde la porte est requise. Cette ouvertu re nedolt pas6tre obstruee Iorsque

la porte est en place. Une porte a volets dont lesouvertures totalisent la norme

d_crite ci-dessus est acceptable.

DEGAGEMENTS MINIMAUX POUR L'INSTALLATION en po (cm)

D'AVANT COTES ARRIERE DESSUS

AIc6ve ou sous un

comptoir 0 (0) 0 (0) 0 (0) 0 (0)

Armoire 1 (2,54) 0 (0) 0 (0) 0 (0)

A6ration n_cessairedans la porte de I'armoire: 2 ouvertures a persiennes de 60

pouces carr_s (387 cm carr_s) chacun- a 3 pouces(7,6 cm) du haset du haut de la

porte.

L'AERATION DE CETTESECHEUSESEFAIT VERSL'EXTERIEUR.

5. Lesillustrations qui suivent donnent led6gagement minimum pour une installation

dans une alc6ve ou un placard.

_;;_ 0 cm(0 po)

0 cm (0 po)

,," :),54 ¢m

_11 _

(1 po) ,,

u _u'_ O crn(0 pc))

ii \

]

PORTE DU PLACARD

Dimensions D'lnstallation De Secheuse

Ind_pendant Et Sous Le Compteur

48.5" _' I'espace fibre ouvrez la porte

(123.19cm)

27.25Pour affronter le coffret

27.75Aux boutons clairs

Pipe d'offre de

gaz sur I'arri_re

de I'unit_

,,_5.0" (12.7cm) 2.28"

v Ligne taille centrale

pour arriere, droit,

patti, passage

4.375" (11.12cm) Aux _chappemer

8.875" (14.93cm) Aux _chappemer

(69.22cm)

(70.49cm)

Afimentation _lectrique sur I'arri_re de I'unit_

ts lat_raux

ts bas

i i

36"

"91.44cm)

I"TI', *

1_.o !Aux _chappements

d'arri_re et de base

27.0"

(68. 58cm)

28.8A la poign_e claire de porte (72.39cm)

Dimensions Empil_es D'lnstallation De Secheuse

28.25"Pour affronter le coffret(71.76cm)

28.75" Aux boutons dairs (73.03cm)

29.5"A la poign_e claire de porte (74.93cm)

49'_, I'espace fibre (124.46cm)

ouvrez porte

72.00"

(11.12cm) (182.88cm)

4.375"

Echappements

Lat_raux

(104.14cm)

Ligne taille

centrale

pour arriere,

droit, patti,

passage

(34.29cm)

13.5"

Pipe d'offre de

gaz sur I'arriere

de I'unit_

38.25"

(97.16cm)

(68. 58cm)

27.0"

Afimentation

61ectrique sur

I'arri_re de

I'unit_

INSTALLATION DANS UNE MAISON MOBILE

1. L'_vacuation d'air de las_cheuse DOITse faire a I'ext_rieu r

de la maison (aI'_xterieur et non pasau-dessousde lamaison

mobile) a I'aide de conduit en m_tal non inflammable,

I'_preuve du feu. Lesconduits en metal doivent avoir 10,16

cm (4 pouces) de diam_tre sansobstructions. Lesconduits

en m_tal rigide sont preferables.

2. Si la conduite d'_vacuation d'air traverse le plancher et un

espaceferm_ situe sous la maison mobile, I'evacuation d'air

DOITseterminer a I'ext_rieurdecet espacefermi, et lasortie

bien fix_e a la structure de la maison mobile.

3. Lorsde I'installation d'une s_cheuseagaz dans une maison

mobile, ilfaut pr_voir un apport d'air ext_rieur. L'espace

pr_voir doit Ctre superieur de deux fois celui du conduit

d'_vacuation de la secheuse.

4. Cette s_cheuse DOIT6tre fix_e au plancher. L'ensemble

d'installation no. 169840 pour maison mobile estdisponible

chez votre distributeur.

5. Ser_f_rer aux pages2 et3 pourde plusamples informations

ur lesexigences de ventilation.

6. L'installation DOlT respecter la norme f_d_rale sur la

construction et la s_curite des maisons mobiles en vigueur

(Manufactured Home Construction & SafetyStandard)(partie

int_grante du r_glement f_d_ra124 CFRPartie 32-80) ou,

Iorsque cette norme nes'applique pas, elle doit respecter la

norme nationale americaine pour les maisons mobiles

(American National Standard for Mobile Homes). Lorsque

I'installation sefait au Canada, elle doit se conformer aux

normes ACNOR Z240.

Las_cheuseest concue conform_ment

la norme ANSI Z 21.5.1 pour un USAGE DOMESTIQUE

seulement.

DEBALLAGE

1. A I'aide desquatre coins de protection de I'emballage (deux

sur chaque c6te), d@oser delicatement la secheusesur son

c6t_ gauche et retirer le morceau de mousse place sous la

s_cheusepour I'exp_dition.

Pour ne pas endommager la s_cheuse, ne

pas prendre prisesurlepanneau de commande pour soulever

ou d_placer la s_cheuse.

REMARQUE :Silas_cheusedoit 6tre install_e sousun com ptoir,

le panneau du dessuspeut 6tre d6monte pour I'installation.

2. Remettre la secheuse a la verticale.

MORCEA U

DE MOUSSE

EMBALLAGE

PORTE RL'VERSIBLE

Instructions pour changer I'ouverture

de la Porte sans Fen@tre :

I. Ouvrez la Porte et enlevez les4 bouchons d'en face oQon trouve

la charni_re. Conservez toutes les pieces pour les utiliser

post_rieurement, a moins qu'on nesp_cifie le contraire. Note •Ayez

des soins en enlevant les bouchons, pour ne pas abimer la peinture

dans le Panneau Frontal.

LES 4 VIS

(UNE DE CHAQUE

2. D_tendez les quatre (4) vis qui tiennent la charni_re au Panneau

Frontal. Pour de meilleurs r_sultats, enlevez seulement une des vis.

Enlevez ensuite les deux restants, entretemps prennez la porte

fermement, pour _viter qu'il tombe et cause desdegats b la charni_re,

le Panneau Frontal ou a la Porte. Apr_s avoir d_tendu lesvis restantes,

enlevez les compl_tement.

3. Placez la Porte, avec le c6t_ de la charni_re vers le has, sur une

serviette ou un matelas _troit, pour _viter qu'il soit doubl_. Enlevez

les quatre (4) vis restantes entre la charni_re et la porte.

4. Enlevez quatre (4) vis dans le c6t_ oppose de la Porte

5. %parez I'anneau int_rieur de I'ext_rieur de la Porte, en plat;ant

un tournevis plat ou un couteau sansbord. Tournez I'anneau int_rieur

180 degr_s et unis a nouveau les deux moiti_s de la porte.

6. Installez quatre (4) vis pour assurer les moiti_s de la Porte, oO il

_tait attach_e la charni_re

7. Installez quatre (4) vis pour assurer lejoint de la charni_re

8. Enlevez le contre de la charni_re et jetez le aux ordures

9. Enlevez le bouchon carr_ et installez-le dans le trou o0 vous avez

enl_ve le contre

10. Installez le contre (raCine qui est fourni dans la bourse de la

Litt_rature) dans le trou tomb_juste, o0 vous avez enl_ve le bouchon

1I. En prenant la porte fermement de la partie superieure, mettez la

pros de la cavit_ et iassurez vous d'aligner le trou sup_rieur de la

charni_re avec le trou superieur du Panneau Frontal. Une fois que

vous avez commence a placer la premiere vis, placez la deuxi_me

dans I'inf_rieur de la charni_re. Quand tousles deux soient serr_s,

installez les autres deux vis.

12. Installez quatre (4) bouchons dans lestrous du Panneau Frontal,

o0 _taient placees les charni_res a I'origine

Instructions pour changer I'ouverture de la Porte avec Fen tre

Figure 1

1. Ouvrez la Porte et enlevez les 4 bouchons d'en face oQ on

trouve la chami@e. Conservez toutes les pieces pour les

utiliser post@ieurement, a moins qu'on ne specifie le

contraire. (Figure 1). Note: Ayez des soins en enlevant les

bouchons, pour ne pas abimer la peinture dans le Panneau

Frontal.

Figure 2

Figure 4

5. Enlevez deux (2) vis de la poignee et deux (2) bouchons

de la Porte ; en prennant soin de ne pas doubler la peinture

de la Porte. (Figure 4).

2. Detendez les quatre (4) vis qui tiennent la charniere au

Panneau Frontal. (Figure 2). Pour de meilleurs resultats,

enlevez seulement une des vis. Enlevez ensuite les deux

restants, entretemps prennez la porte fermement, pour eviter

qu'il tombe et cause des degats a la charni@e, le Panneau

Frontal ou a la Porte. Apres avoir detendu les vis restantes,

enlevez les completement.

Figure 3

Figure 5

7. Retirez la poignee loin du joint de la porte.

(Figure 5).

Figure 6

7. Separez la porte externe du joint interne de la porte avec

un couteau ou avec un tournevis plat. (Figure 6).

3. Placez la Porte, avec le cSte de la charniere vers le bas,

sur une serviette ou un matelas etroit, pour eviter qu'il soit

doubl& Enlevez les quatre (4) vis restantes entre la

charniere et la porte. (Figure 3).

4. Enlevez quatre (4) vis du c6te de la Porte, oQ etait

installee la charniere.

Figure 7

11.Montez a nouveau la lentille a I'anneau de transition avec

les trous pour installer la poignee dans le c6te droit de

I'assemblage de la porte. Pour I'ajustement approprie,

assurez que les languettes de retenue dans I'anneau de

transition sont sur la lentille.

8. Enlevez la vis qui fixe la lentille. (Figure 7).

Figure 8

9. en separant plusieurs des languettes de retenue et retirez

la lentille loin de I'anneau de transition. (Figure 8).

Figure 9

Figure 10

Figure 11

12. Installez a nouveau la Porte externe au joint interne de la

porte. (Figure 11)

13. lnstallez quatre (4) vis pour tenir la charniere dans sa

nouvelle situation, en assurant que la charniere ait

I'orientation correcte.

14. tnstallez quatre (4) vis dans les trous oQ etait soumise la

charniere.

15. Enlevez le contre de la charniere et jetez le aux ordures.

16. Enlevez le bouchon carre et installez-le dans le trou oQ

vous avez enleve le contre.

17. lnstallez le contre (m6me qui est fourni dans la bourse

de la Litterature) dans le trou tombe juste, oQ vous avez

enleve le bouchon.

10. Enlevez deux (2) bouchons de I'anneau de transition et

reinstallez au c6te precedent de la poignee. (Figures 9 et 10)

Figure 12

18. Reinstallez de la poignee de la Porte, en faisant passer

les protuberances d'assemblage de cette derniere, a travers

les trous dans le verre et I'annelle et en plagant des vis

travers le panneau interieur de la Porte et en les serrant

dans les protuberances de la poignee. (Figura 12).

19. En prenant la porte fermement de la partie superieure,

mettez la pres de la cavite et iassurez vous d'aligner le trou

superieur de la charniere avec le trou superieur du Panneau

Frontal. Une fois que vous avez commence a placer la

premiere vis, placez la deuxieme dans I'inferieur de la

charniere. Quand tousles deux soient serres, installez les

autres deux vis.

20. lnstallez quatre (4) bouchons dans les trous du Panneau

Frontal, oQetaient placees les charnieres a I'origine

La page charge ...

Crosley FEQ1452CKS0 Guide d'installation

Marque: Crosley

Modèle: FEQ1452CKS0

Catégorie: Sèche-linge électriques

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Crosley FEQ1452CKS0 Installation guide

Crosley FEQ1452CKS0 Guide d'installation

Ce manuel convient également à

Crosley FEQ1452CKS0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents