LG GRP2066TLQA.CGSQGSF Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
2
Entry
Important safety instruction
Identification of parts
Where to install
Door removal
Door replacement
Feed water pipe installation
Height adjustment
Starting
Adjusting the temperatures and functions
Refreshment center (Applicable to some models only)
Shelf (Applicable to some models only)
Wine holder (Applicable to some models only)
Egg box (Applicable to some models only)
Humidity control in the vegetable compartment
Convert into a vegetable or meat compartment (Applicable to some models only)
Deodorizer (Applicable to some models only)
Miracle Zone Temperature Transition Corner (Applicable to some models only)
Temperature Change at Miracle Zone (Applicable to some models only)
Miracle Zone (Applicable to some models only)
Location of foods
Storing foods
How to dismantle parts
General information
Cleaning
Trouble shooting
Table of contents
Introduction
Installation
Operation
Suggestion on
food storage
Care and
maintenance
3
3
4
5
6
7
7
8
9
9
14
15
15
15
16
16
16
17
17
17
18
19
20
22
22
23
Entry
The model and serial numbers are found on the inner case or back of refrigerator
compartment of this unit. These numbers are unique to this unit and not
available to others. You should record requested information here and retain
this guide as a permanent record of your purchase. Staple your receipt here.
Date of purchase :
Dealer purchased from :
Dealer address :
Dealer phone no. :
Model no. :
Serial no. :
Before it is used, this refrigerator must be properly installed and located in accordance
with the installation instructions in this document.
Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and
pull it straight out from the outlet.
When moving your appliance away from the wall, be careful not to roll over the power
cord or to damage it in any way.
After your refrigerator is in operation, do not touch the cold surfaces in the freezer
compartment
, particularly when your hands are damp or wet. Skin could adhere to
these extremely cold surfaces.
Unplug the power cord from the power outlet for cleaning or other requirements. Never
touch it with wet hands because you can get an electric shock or be hurt.
Never damage, process, severely bend, pull out, or twist the power cord because
damage the power cord may cause a fire or electric shock. You have doubts on whether
the appliance is properly grounded.
Never place glass products in the freezer because they may be broken due to expansion
when their contents are frozen.
Never allow your hands within the ice storage bin of the automatic ice maker. You could
be hurt by the operation of the automatic ice maker.
The appliance is not intended for use by young children or infirm persons without
supervision.
Young children should be supervised to ensure that they do not play with the appliance.
Never allow anyone to climb, sit, stand or hang on the refreshment center door. These
actions may damage the refrigerator and even tip it over, causing severe personal injury.
If possible, connect the refrigerator to its own individual electrical outlet to prevent it and
other appliances or household lights from causing an overload that could cause a power
outage.
The refrigerator-freezer should be so positioned that the supply plug is accessible for
quick disconnection when accident happens.
If the supply cord is damaged, it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
Do not modify or extend the Power Cord length.
It will cause electric shock or fire.
Introduction
3
Important safety instruction
Don’t use an
extension cord
Accessibility of
Supply Plug
Supply Cord
Replacement
Warning
4
Introduction
Identification of parts
DANGER: Risk of child entrapment.
Before you throw away your old refrigerator or freezer:
Take off the doors but leave the shelves in place so that children may not easily climb
inside.
The appliance is not intended for use by young children or infirm persons without
supervision.
Young children should be supervised to ensure that they do not play with the appliance.
Don’t store or use gasoline or other flammable vapor and liquids in the vicinity of this or
any other appliance.
In the event of an electric short circuit, grounding (earthing) reduces the risk of electric
shock by providing an escape wire for the electric current.
In order to prevent possible electric shock, this appliance must be grounded
improper use of the grounding plug can result in an electric shock. Consult a qualified
electrician or service person if the grounding instructions are not completely
understood, or if you have doubts on whether the appliance is properly grounded.
Child entrapment
warning
Don’t store
Grounding (Earthing)
If you found some parts missing from your unit, they may be parts only used in other
models. (i.c. the “Refreshment center” is not included in all models)
NOTE
Freezer
compartment
Refrigerator
compartment
Milk product corner
Door rack
Space plus
Lamp
Automatic
ice maker
Shelf
(steel or glass)
Shelf
Door rack
Drawer
Door rack
Lower cover
Lamp
Shelf
Door rack
(1piece or 2piece)
Door rack
(1piece or 2piece)
Door rack
Shelf
Snack drawer (Optional)
Shelf (Folding or Normal)
Refreshment center
(Optional)
Egg box
Vegetable drawer
(1 or 2)
Miracle Zone (Optional)
Fresh compartment
(Optional)
Conversion switch
(Meats/Vegetables)
(Optional)
Humidity switch
Wine holder
(Plastic or wire)
5
Select a good
location
1. Place your appliance where it is easy to
use.
2. Avoid placing the unit near heat sources,
direct sunlight or moisture.
3. To ensure proper air circulation around the
fridge -freezer, please maintain sufficient
space on both the sides as well as top and
maintain at least 2 inches (5 cm) from the
rear wall.
4. To avoid vibrations, the appliance must
be leveled.
5. Don't install the appliance below 5°C. It may cause affect the performance.
Where to Install
Disposal of the
old appliance
This appliance contains fluid (refrigerant, lubricant)and is made of parts and materials
which are reusable and/or recyclable.
All the important materials should be sent to the collection center of waste material
and can be reused after rework (recycling). For take back, please contact with the
local agency.
Installation
6
Installation
Door removal
Failure to do so could result in death or serious injury.
If your access door is too narrow for the
refrigerator to pass through, remove the
refrigerator door and pass the refrigerator laterally.
Electric Shock Hazard
Disconnect electrical supply to refrigerator before installing.
Remove the lower cover by lifting upward, and
remove clip, and then pull up the feed water tube
while pressing area
shown in the figure to the
right.
Remove lower
cover and
then feed water
tube
Warning
Remove the
freezer
compartment
door
Remove the
refrigerator
door
1) Removing the hinge cover by loosening the
screws. Separate all connection wires except
for the earth line after.
2) Remove the keeper by rotating it counter
clockwise (
)
and then lifting the upper
hinge up(
).
3) Remove the freezer compartment door by
lifting it upward. This time, the door should
be lifted enough for the feed water pipe tube
to be completely pulled out.
1) Loosen the hinge cover screws and remove
the cover. Remove connection wire, if any,
except for the earth line.
2) Remove keeper by rotating it clockwise (
)
and then remove the upper hinge by lifting
it up (
).
3) Remove the refrigerator compartment door
by lifting it up.
If a tube end is deformed or abraded, cut the part away.
NOTE
When removing the upper hinge, be careful that the door does not fall forwards .
NOTE
Move the refrigerator compartment door passing through the access door and lay
it down, but be careful not to damage the feed water pipe tube.
NOTE
Lower cover
Lower hinge
Lower hinge
Keeper
Feed water tube
Connection
wires
Hinge
cover
Upper hinge
Keeper
Upper hinge
Earth line
Upper hinge
Connection
wires
7
Installation
Door replacement
Feed water pipe installation
Pass the refrigerator laterally through the access
door as shown in the right figure.
Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5
kgf/cm
2
) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).
Keep the total length of the feed water pipe tube within 8 m and be careful for the
tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed
owing to the drain water pressure.
Install the feed water pipe tube at a place free from heat.
Connect to potable water supply only.
Refer to instructions with water filter kit for installation.
Mount them in the reverse sequence of removal after they pass through the access
door.
Pass the
refrigerator
Before
installation
Warning
1
2
3
4
5
M
a
x
F
R
Z
T
E
M
P
R
E
F
T
E
M
P
M
i
n
5
43
2
1
M
a
x
8
Installation
Height adjustment
Level the door by inserting flat (
-
type) driver into the groove of the left height adjusting
screw and rotate it clockwise ().
Level the door by inserting flat (
-
type) driver into the groove of the right height
adjusting screw and rotate it clockwise ().
The refrigerator doors will close smoothly by heightening the front side by adjusting
the height adjusting screw. If the doors do not close correctly, performance may be
affected.
If the freezer
compartment door
is lower than the
refrigerator
compartment door
If the freezer
compartment door
is higher than the
refrigerator
compartment door
After leveling the
door height
Next
1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.
2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their
proper places. They are packed together to prevent possible damage during shipping.
3. Connect the power supply cord (or plug) to the outlet. Don't double up with other
appliances on the same outlet.
9
Starting
When your refrigerator is first installed, allow it to stabilize at normal operating
temperatures for 2-3 hours prior to filling it with fresh or frozen foods.
If operation is interrupted, wait 5 minutes before restarting.
Adjusting the temperatures and functions
Operation
10
Operation
You can adjust temperature of and freezer room and refrigerator room.
Whenever pressing button, setting is repeated in the order of (Middle)
(Middle Strong)
(Strong)
(Weak)
(Middle Weak).
The actual inner temperature varies depending on the food status, as the
indicated setting temperature is a target temperature, not actual temperature
within refrigerator.
Refrigeration function is weak in the initial time. Please adjust temperature as
above after using refrigerator for minimum 2~3 days.
Middle(-19
0
C)
Middle strong(-22
0
C)
Strong(-23
0
C)
Weak(-15
0
C)
Middle weak(-17
0
C)
Middle(3
0
C)
Middle strong(2
0
C)
Strong(0
0
C)
Weak(6
0
C)
Middle weak(4
0
C)
You can select water or ice.
Please select water, slice ice and square ice
by pressing button as you desire.
Please press the push button lightly by
catching and pushing in cup.
The border line is indicated for the selected
function,
"Tak!" sounds if 5 seconds pass after ice
comes out.
It is sound that the outlet of ice is closed.
How to adjust the
temperature in
the freezer
compartment
How to adjust the
temperature in
the refrigerator
compartment
Dispenser use
selection
DISPENSER
WATER
<Type-1,2> <Type-3>
CUBE
CRUSH
WATER
CUBE
CRUSH
DISPENSER
Reference : Please wait for 2-3 seconds in order to take
final ice slices or drops of water when taking
out cup from the pressing switches after taking
ice or water.
Pressing
Switch
11
Operation
The icemaker can automatically make 8 pieces of ice cubes at anyone time,
approximately 80 pieces per day. However these quantities may vary according to
certain conditions. E.g. the duration and amount of times the refrigerator door is
opened.
The Ice making proceeds ceases automatically when the ice storage bin is full.
If you choose not to use the automatic ice making function, repositioned the
icemaker selection switch to the off position or the on position for reselection. Note:
The manual selection function is only applicable to some models only.
Ice is lumped together
When ice is lumped together, take the ice lumps out of the ice storage bin, break
them into small pieces, and then place them into the ice storage bin again.
When the ice maker produces too small or lumped together ice, the amount of
water supplied to the ice maker need to adjusted. Contact the service center.
If ice is not used frequently, it may lump together.
Power failure
Ice may drop into the freezer compartment. Take the ice storage bin out and discard
all the ice then dry it and place it back. After the machine is powered again, crushed
ice will be automatically selected.
The unit is newly installed
It takes about 12 hours for a newly installed refrigerator to make ice in the freezer
compartment.
Automatic ice
maker
When ice maker
does not operate
smoothly
Please select this function for prompt
freezer.
"On" is repeated whenever pressing
button.
The arrow mark graphic remains at the On
status when selecting Special Refrigeration
"On".
Super freezer function automatically turns
off if a fixed time passes.
Express freezer
It is normal that a noise is produced when ice made is dropped into the ice storage
bin.
NOTE
EXPRESS FRZ
This button stops operation of
different button.
Locking or Release is repeated whenever
pressing the .
Pressing the other button when selecting
‘LOCK’, the button does not operate.
Lock
LOCK
Operation
12
How to use
dispenser
Select one among crushed ice, water, and cubed ice and slightly press the push
switch with a glass or other container.
The other
functions
Door open warning
3 times of warning sounds at the interval of 30 seconds if a minute passes with the
door of refrigerator and the hombar door opened or completely closed.
Please contact with the local service center if warning continue to sound even after
closing the door.
Diagnosis (failure detection) function
Diagnosis function automatically detects failure when failure is found in product during
the use of refrigerator.
If failure occurs at product, it does not operate though pressing any button and normal
indication is not done. In this case, do not turn power off but immediately contact with
the local service center. A lot of time are need for service engineer to detect the failed
part if turning it off.
Crushed ice
Light the crushed ice
indicating lamp by
pressing the selection
button.
C
rushed
ice will be
dispensed by pressing the
push switch with a glass.
Water
Light the water
indicating lamp by
pressing the selection
button.
Water will be dispensed
by pressing the push
switch with a glass.
Cubed ice
Light the cubed ice
indicating lamp by
pressing the
selection button.
Cubed ice will be dispensed
by pressing the push
switch with a glass.
Water is cooled while stored in the water tank in the refrigerator compartment, and
then sent to the dispenser.
Ice is made in the automatic ice maker and sent to the dispenser divided into crushed
or cubed form ice.
How ice/cold
water is supplied
It is normal that the water is not very cold at first. If you want colder water, add
ice into the glass.
NOTE
Operation
13
Throw away the ice (about 20 pieces) and water (about 7 glasses) first made after
refrigerator installation.
The first ice and water may include particles or odor from the feed water pipe or feed
water box. This is necessary in case that the refrigerator has not been used for a long
time.
Keep children away from the dispenser.
Children may push switch incorrectly bad or damage
lamps.
Be careful that food is not block the ice passage.
If foods are placed at the entrance of ice passage, ice
may not be dispensed. The ice passage may also be
covered with ice powder if splinter ice is used only. This
time, remove the ice powder accumulated.
Never store beverage cans or other foods in ice
storage bin for the purpose of rapid cooling.
Such actions may damage the automatic ice maker.
Never use thin crystal glass or crockery to collect ice.
Such glasses or containers may be broken.
Put ice first into a glass before filling water or other beverages.
Water may be splashed if ice is added to existing liquid in a glass.
Never touch a hand or other tools on ice outlet.
Touch may cause a part breakage or hand injury.
Never remove the ice maker cover.
Sometimes level the surface so that the ice storage bin is fully filled with ice.
Ice is piled up just near the ice maker. So, such status may be considered, by the ice
maker, that the ice storage bin is fully filled and ice making operation may stop.
If discolored ice is dispensed, immediately contact service center, stopping use.
Never use too narrow or deep glass.
Ice may be jammed in ice passage and, thus, the refrigerator may be failed.
Keep the glass at a proper distance from ice outlet.
A glass too close to the outlet may hinder ice from coming out.
Cautions
As demonstrated below, it displays the months left in units of 30 days until the filter
replacement is required, starting from when the refrigerator power usage is
authorized.
After 6 months, the following sentence and will appear on the filter condition
part of the LED. "Press for 3 seconds after replacing filter"
After 6 months have passed, and if the filter has been replaced or you want to reset
the filter condition display, press the filter replacement button for more than 3
seconds and it will reset to the initial Power On state.
6 Filter condition
(filter replacement
cycle) display
function
(Applicable to
some models only)
<Type - 1>
<Type - 2>
After 6 months have passed the filter change icon will appear
on the display.
14
Operation
Refreshment center (Applicable to some models only)
Open the refreshment center door.
You can access the refreshment center
without opening refrigerator door and thus
saving electricity.
Inner lamp is lit in refrigerator compartment
when the refreshment center door opens.
Thus it is easy to identify the contents.
Never use the refreshment center door as a
chopping board and take care not to damage it
with sharp tools.
Never rest your arms or severely press on it.
The
refreshment center
can not function
normally without the cover.
Not only can the refreshment center door may
be damaged, but also children may be hurt.
How to use
Never place
heavy items on
the refreshment
center door or
allow children to
hang it on.
Never take out
the inner
refreshment
center cover
Use the
refreshment
center door as a
stand
15
Operation
Egg box (Applicable to some models only)
Never use the egg box as an ice storage bin. It can be broken.
Never store the egg box in the freezer compartment or fresh compartment.
NOTE
Shelf (Applicable to some models only)
Wine holder (Applicable to some models only)
You can store taller items such as a gallon container or bottles by simply pushing in
front half of shelf underneath back half of shelf. Pull toward you to return to a full shelf.
Folding Shelf
In case of inserting the wine holder :
Pull the wine holder downward as in
after inserting it into the side anchoring
part of the shelf as in
by catching it
upward as in
.
In case of separating the wine holder :
Pull the wine holder inward as in
after
holding it upward as in
by catching it.
Bottles can be stored laterally with
this wine corner.
This can be attached to any shelf.
Wine holder
adjustment
(Type 1)
(Type 2)
[Type-1] [Type-2]
You can move the egg box to wherever you want.
Bottles can be stored laterally with this
wine rack.
16
Operation
Humidity control in the vegetable compartment
The humidity can be controlled by adjusting the humidity control switch to the
left/right when storing vegetables or fruits.
High humidity
Low humidity
Convert into a vegetable or meat compartment
(Applicable to some models only)
The
meat
compartment maintains the temperature at a lower point than the
refrigerator compartment so that meat or fish can be stored fresh longer.
The bottom drawer in the refrigerator can be converted into a vegetable or meat
compartment
Vegetables or fruits are frozen if the conversion switch is set to meats
compartment. So, be sure to check it before storing foods.
NOTE
Deodorizer (Applicable to some models only)
This system efficiently absorbs strong
odors by using the optical catalyst. This
system does hot have any affect on
stored food.
Since it is installed already installed onto the cool air intake duct from the from
the refrigerator compartment, you need no separate installation.
Please use closed containers to store food with pungent odors.
Otherwise, this oder can be absorbed by other food in the compartment.
How to use the
deodorizing
system
Operation
17
Miracle Zone Temperature Transition Corner
(Applicable to some models only)
Miracle Zone (Applicable to some models only)
By pressing the button, store vegetables,
fruits or other types of food such as meat to
be defrosted, raw fish, etc.
Temperature Change at Miracle Zone
(Applicable to some models only)
You can select optimum
temperature range depending on
types of foods stored.
- 3-step of temperature selection
including -3°C, -1°C and 4°C is
available. Vegetables/fruits and cold
storage foods requiring humidity
maintenance and meats/fishes can
be more freshly stored depending on type of foods stored.
First, remove the vegetable bin.
After lifting the Miracle Zone case slightly , reach
inside and pull it outward .
When using the Miracle Zone as storage room of meats, storing vegetables or fruits
may be frozen
When using the Miracle Zone as storage room of meats, keeping meats or fishes
may be spoiled and thus meats or fishes must be kept at the F-room.
If opening a door of the R-room, lamp turns on in the selected status and lamp turns
off if closing it.
(Vegetable/Fruit)
(Cold storage while maintaining humidity)
(Meat) is
sequentially repeated whenever pressing the "Selection" button.
When removing
Miracle Zone
Method to Use
Fit the Miracle Zone case on to the ledge and
gently slide it in .
When forced, the connecting parts can be damaged.
When installing
Miracle Zone
18
Suggestion on food storage
Location of foods
(Refer to identification of parts)
Store wine.
Store small foods such as bread, snacks, etc..
Store various frozen foods such as meat, fish,
ice cream, frozen snacks, etc..
Store small packed frozen food.
Temperature is likely to increase as door
opens.
So, do not store long-term food such
ice cream, etc..
Wine holder
Snack
drawer
Freezer
compartment
shelf
Freezer
compartment
door rack
Freezer
compartment
drawer
Milk product
corner
Egg box
Refreshment
center
Refrigerator
compartment
shelf
Refrigerator
compartment
door rack
Vegetable drawer
Vegetable
drawer
/meat
drawer
conversion corner
Store meat, fish, chicken, etc.. after
wrapping them with thin foil.
Store dry
.
Store milk products such as butter, cheese,
etc..
Place this egg box in the proper location.
Store foods of frequent use such as beverage,
etc..
Store side dishes or other foods at a proper
distance.
Store small packed food or beverages such
as milk, juice, beer, etc..
Store vegetables or fruits.
Store vegetable, fruits, meat to thaw, raw
fish, etc.. setting the conversion switch as
necessary.
Be sure to check the conversion switch
setting before storing foods.
Suggestion on food storage
19
Storing foods
Store fresh food in the refrigerator compartment. How food is frozen and thawed is an
important factor in maintaining its freshness and flavor.
Do not store food which goes bad easily at low temperatures, such as bananas, and
melons.
Allow hot food to cool prior to storing, placing hot food in the refrigerator could spoil
other food, and lead to higher energy consumption.
When storing the food, cover it with vinyl wrap or store in a container with a lid. This
prevents moisture from evaporating, and helps food to keep its taste and nutrients.
Do not block air vents with food. Smooth circulation of chilled air keeps refrigerator
temperatures even.
Do not open the door frequently. Opening the door lets warm air enter the refrigerator,
and cause temperatures to rise.
Never keep too much food in door rack because they may push against by inner racks
so that the door cannot be fully closed.
Do not store bottles in the freezer compartment - they may break when frozen.
Do not refreeze food that has been thawed. This causes loss of taste and nutrient.
When storing frozen food like ice cream for a long period, place it on the freezer
shelf, not in the door rack.
Do not touch the cold foods or containers- especially made of metallic -, with wet
hands and place glass products in the freezer compartment.
- That’s why you may have chilblains and they may be broken when their inner matters
are frozen, causing personal injury.
Avoid placing moist food in top refrigerator shelves, it could freeze from direct
contact with chilled air.
Always clean food prior to refrigeration. Vegetables and fruits should be washed and
wiped, and packed food should be wiped, to prevent adjacent food from spoiling.
When storing eggs in their storage rack or box, ensure that they are fresh, and always
store them in an upright position, which keeps them fresh longer.
Freezer
compartment
Refrigerator
compartment
If you keep the refrigerator in a hot and humid place, frequent openning of the door
or storing a lot of vegetables in it may cause dew to form which has no effect on its
performance. Remove the dew with dust cloth free from care.
NOTE
20
Care and maintenance
How to dismantle parts
Freezer
compartment
lamp
Dispenser lamp
Freezer
compartment
shelf
Door rack and
support
Space plus
Ice storage bin
After dispenser
is used
Separate the lamp by pulling it out, and then
remove the lamp. Max. 15 W bulb for
refrigerator is used and can be purchased at a
service center.
To remove a shelf, lift the left part of the shelf
a bit, push it to the direction (), lift the right
part to the direction
(
)
, and take it out.
Lift the door rack holding both sides () and
pull it out to
(
)
direction.
Lift the space plus () and pull it out to
(
)
direction.
The water collector has no self-drainage
function. So it should be cleaned regularly.
Remove the cover by pulling the front of the
water collector cover and dry it with a cloth.
Hold the ice storage bin as shown in the right
figure and pull it out
(
)
while slightly lifting it
().
It is recommended not to dismantle the ice
storage bin unless it is necessary.
Be sure to use both hands when removing
the ice storage bin, so as not to drop it on the
floor.
If the ice storage bin does not fit well, slightly
rotate the rotating device.
Dismantling is done in the reverse sequence of assembly.
Be sure to unplug the power plug before dismantling and assembly.
Never apply severe force to dismantle parts. Parts may be damaged.
NOTE
Separate the lamp by pulling it out
(
)
while
slightly striking
() and rotating
(
)
the lamp
cover.
Turn the bulb counterclockwise. Max. 40 W
bulb
for refrigerator is used and can be purchased at
a service center.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82

LG GRP2066TLQA.CGSQGSF Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire