Lincoln Electric LN-7 Mode d'emploi

LN-7 & LN-7 GMA WIRE FEEDER

Operator’s Manual

Save for future reference

Date Purchased

Code: (ex: 10859)

Serial: (ex: U1060512345)

IM351-C | Issue D ate 13-May

For use with machines having Code Numbers:

9100; 9168; 9386; 9484; 9641; 9643;

9644; 9796; 9928; 9929; 9930; 9931;

10223; 10225; 10323; 10325; 10363;

10364; 10737; 12037

Register your machine:

www.lincolnelectric.com/register

Authorized Service and Distributor Locator:

www.lincolnelectric.com/locator

THANK YOU FOR SELECTING

A QUALITY PRODUCT BY

LINCOLN ELEC TRIC.

PLEASE EXAMINE CARTON AND EQUIPMENT FOR

DAMAGE IMMEDIATELY

When this equipment is shipped, title passes to the purchaser

upon receipt by the carrier. Consequently, claims for material

damaged in shipment must be made by the purchaser against the

transportation company at the time the shipment is received.

SAFETY DEPENDS ON YOU

Lincoln arc welding and cutting equipment is designed and built

with safety in mind. However, your overall safety can be increased

by proper installation ... and thoughtful operation on your part.

DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT

WITHOUT READING THIS MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,

think before you act and be careful.

This statement appears where the information must be followed

exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed

to avoid minor personal injury or damage to this equipment.

KEEP YOUR HEAD OUT OF THE FUMES.

DON’T get too close to the arc.

U

se corrective lenses if necessary

to stay a reasonable distance

away from the arc.

READ and obey the Safety Data

Sheet (SDS) and the warning label

that appears on all containers of

welding materials.

USE ENOUGH VENTILATION or

exhaust at the arc, or both, to

keep the fumes and gases from

your breathing zone and the general area.

IN A LARGE ROOM OR OUTDOORS, natural ventilation may be

adequate if you keep your head out of the fumes (See below).

USE NATURAL DRAFTS or fans to keep the fumes away

from your face.

If you de velop unusual symptoms, see your supervisor.

Perhaps the welding atmosphere and ventilation system

should be checked.

WEAR CORRECT EYE, EAR &

BODY PROTECTION

PROTECT your eyes and face with welding helmet

properly fitted and with proper grade of filter plate

(See ANSI Z49.1).

PROTECT your body from welding spatter and arc

flash with protective clothing including woolen

clothing, flame-proof apron and gloves, leather

leggings, and high boots.

PROTECT others from splatter, flash, and glare

with protective screens or barriers.

IN SOME AREAS, protection from noise may be appropriate.

BE SURE protective equipment is in good condition.

Also, wear safety glasses in work area

AT ALL TIMES.

SPECIAL SITUATIONS

DO NOT WELD OR CUT containers or materials which previously

had been in contact with hazardous substances unless they are

properly cleaned. This is extremely dangerous.

DO NOT WELD OR CUT painted or plated parts unless special

precautions with ventilation have been taken. They can release

highly toxic fumes or gases.

Additional precautionary measures

PROTECT compressed gas cylinders from excessive heat,

mechanical shocks, and arcs; fasten cylinders so they cannot fall.

BE SURE cylinders are never grounded or part of an

electrical circuit.

REMOVE all potential fire hazards from welding area.

ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR

IMMEDIATE USE AND KNOW HOW TO USE IT.

WARNING

CAUTION

Safety 01 of 04 - 06/15/2016

SECTION A:

WARNINGS

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel Engines

Diesel engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects, and other

reproductive harm.

Gasoline Engines

The engine exhaust from this product contains chemicals known

to the State of California to cause cancer, birth defects, or other

reproductive harm.

ARC WELDING CAN BE HAZARDOUS. PROTECT

YOURSELF AND OTHERS FROM POSSIBLE SERIOUS

INJURY OR DEATH. KEEP CHILDREN AWAY.

PACEMAKER WEARERS SHOULD CONSULT WITH

THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For

additional safety information, it is strongly recommended

that you purchase a copy of “Safety in Welding & Cutting -

ANSI Standard Z49.1” from the American Welding Society,

P.O. Box 351040, Miami, Florida 33135 or CSA Standard

W117.2-1974. A Free copy of “Arc Welding Safety” booklet

E205 is available from the Lincoln Electric Company,

22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION,

MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE POWERED

EQUIPMENT.

1.a. Turn the engine off before troubleshooting

and maintenance work unless the

maintenance work requires it to be running.

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes outdoors.

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from

vaporizing on contact with hot engine parts

and igniting. Do not spill fuel when filling

tank. If fuel is spilled, wipe it up and do not start engine until

fumes have been eliminated.

1.d. Keep all equipment safety guards, covers

and devices in position and in good repair.

Keep hands, hair, clothing and tools away

from V-belts, gears, fans and all other

moving parts when starting, operating or

repairing equipment.

1.e. In some cases it may be necessary to remove safety guards to

perform required maintenance. Remove guards only when

necessary and replace them when the maintenance requiring

t

heir removal is complete. Always use the greatest care when

working near moving parts.

1.f. Do not put your hands near the engine fan. Do not attempt to

override the governor or idler by pushing on the throttle control

rods while the engine is running.

1.g. To prevent accidentally starting gasoline engines while turning

the engine or welding generator during maintenance work,

disconnect the spark plug wires, distributor cap or magneto wire

as appropriate.

1.h. To avoid scalding, do not remove the radiator

pressure cap when the engine is

hot.

ELECTRIC AND

MAGNETIC FIELDS MAY

BE DANGEROUS

2.a. Electric current flowing through any conductor

causes localized Electric and Magnetic Fields (EMF).

Welding current creates EMF fields around welding cables

and welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health effects

which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work

cables. If the electrode cable is on your right side, the

work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as pos-

sible to the area being welded.

2.d.5. Do not work next to welding power source.

SAFETY

Safety 02 of 04 - 06/15/2016

ELECTRIC SHOCK

CAN KILL.

3.a. The electrode and work (or ground) circuits are

electrically “hot” when the welder is on. Do

not touch these “hot” parts with your bare skin or wet clothing.

Wear dry, hole-free gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full area

o

f physical contact with work and ground.

In addition to the normal safety precautions, if

welding must be performed under electrically

hazardous conditions (in damp locations or while

wearing wet clothing; on metal structures such as

floors, gratings or scaffolds; when in cramped

positions such as sitting, kneeling or lying, if there

is a high risk of unavoidable or accidental contact

with the workpiece or ground) use the following

equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic welding

gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection should

be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical (earth)

ground.

3.f. Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of electrode

holders connected to two welders because voltage

between the

two can be the total of the open circuit voltage of both

welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see It ems 6.c. and 8.

ARC RAYS CAN BURN.

4.a. Use a shield with the proper filter and cover plates to protect your

eyes from sparks and the rays of the arc when welding or

observing open arc welding. Headshield and filter lens should

conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant material

to protect your skin and that of your helpers from the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES

CAN BE DANGEROUS.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these fumes and gases.

When welding, keep your head out of the fume. Use enough

ventilation and/or exhaust at the arc to keep fumes and gases

away from the breathing zone. When welding hardfacing

(see instructions on container or SDS) or on lead

or cadmium plated steel and other metals or

coatings which produce highly toxic fumes, keep

exposure as low as possible and within applicable

OSHA PEL and ACGIH TLV limits using local

exhaust or mechanical ventilation unless exposure

assessments indicate otherwise. In confined

spaces or in some circumstances, outdoors, a

respirator may also be required. Additional

precautions are also required when welding

on galvanized steel.

5. b. The operation of welding fume control equipment is affected by

various factors including proper use and positioning of the

equipment, maintenance of the equipment and the specific

welding procedure and application involved. Worker exposure

level should be checked upon installation and periodically

thereafter to be certain it is within applicable OSHA PEL and

ACGIH TLV limits.

5.c. Do not weld in locations near chlorinated hydrocarbon vapors

coming from degreasing, cleaning or spraying operations. The

heat and rays of the arc can react with solvent vapors to form

phosgene, a highly toxic gas, and other irritating products.

5.d. Shielding gases used for arc welding can displace air and

cause

injury or death. Always use enough ventilation, especially in

confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

Safety Data Sheet (SDS) and follow your employer’s safety

practices. SDS forms are available from your welding

distributor or from the manufacturer.

5.f. Also see item 1.b.

SAFETY

Safety 03 of 04 - 06/15/2016

WELDING AND CUTTING

SPARKS CAN CAUSE

FIRE OR EXPLOSION.

6.a. Remove fire hazards from the welding area. If

this is not possible, cover them to prevent the welding sparks

f

rom starting a fire. Remember that welding sparks and hot

materials from welding can easily go through small cracks and

openings to adjacent areas. Avoid welding near hydraulic lines.

Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special

precautions should be used to prevent hazardous situations.

Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)

and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is

touching the work or ground. Accidental contact can cause

overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances inside.

They can cause an explosion even though they have been

“cleaned”. For information, purchase “Recommended Safe

Practices for the Preparation for Welding and Cutting of

Containers and Piping That Have Held Hazardous Substances”,

AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free

protective garments such as leather gloves, heavy shirt, cuffless

trousers, high shoes and a cap over your hair. Wear ear plugs

when welding out of position or in confined places. Always wear

safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area

as practical. Work cables connected to the building framework or

other locations away from the welding area increase the

possibility of the welding current passing through lifting chains,

crane cables or other alternate circuits. This can create fire

hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “Standard for Fire Prevention During

Welding, Cutting and Other Hot Work”, available from NFPA, 1

Batterymarch Park, PO box 9101, Quincy, MA 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER MAY EXPLODE IF

DAMAGED.

7.a. Use only compressed gas cylinders containing

the correct shielding gas for the process used

and properly operating regulators designed for

the gas and pressure used. All hoses, fittings,

e

tc. should be suitable for the application and

maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to

an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected

to physical damage.

• A safe distance from arc welding or cutting operations

and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight

except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders,

associated equipment, and CGA publication P-l, “Precautions for

Safe Handling of Compressed Gases in Cylinders,” available from

the Compressed Gas Association, 14501 George Carter Way

Chantilly, VA 20151.

FOR ELECTRICALLY

POWERED EQUIPMENT.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical

Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

Refer to

http://www.lincolnelectric.com/safety

for additional safety information.

SAFETY

Safety 04 of 04 - 06/15/2016

iv

SAFETY

iv

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instruc-

tions et les précautions de sûreté specifiques qui parraissent

dans ce manuel aussi bien que les précautions de sûreté

générales suivantes:

Sûreté Pour Soudage A LʼArc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à lʼélectrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien sʼisoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une

grande partie du corps peut être en contact avec la

masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans lʼeau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à soud-

er parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode sʼapplicuent aussi au pistolet de

soudage.

2. Dans le cas de travail au dessus du niveau du sol, se pro-

téger contre les chutes dans le cas ou on recoit un choc. Ne

jamais enrouler le câble-électrode autour de nʼimporte quelle

partie du corps.

3. Un coup dʼarc peut être plus sévère quʼun coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi quʼun verre blanc afin de se protéger les yeux du

rayonnement de lʼarc et des projections quand on soude

ou quand on regarde lʼarc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

lʻarc.

c. Protéger lʼautre personnel travaillant à proximité au

soudage à lʼaide dʼécrans appropriés et non-inflamma-

bles.

4. Des gouttes de laitier en fusion sont émises de lʼarc de

soudage. Se protéger avec des vêtements de protection

libres de lʼhuile, tels que les gants en cuir, chemise épaisse,

pantalons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où lʼon pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque dʼincendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque dʼincendie.

8. Sʼassurer que la masse est connectée le plus prés possible

de la zone de travail quʼil est pratique de le faire. Si on place

la masse sur la charpente de la construction ou dʼautres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques dʼincendie ou dʼechauffement des chaines et des

câbles jusquʼà ce quʼils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

dʼopérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de lʼarc peuvent réagir avec les

vapeurs du solvant pour produire du phosgéne (gas forte-

ment toxique) ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

LES MACHINES À SOUDER À

TRANSFORMATEUR ET À

REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code

de lʼélectricité et aux recommendations du fabricant. Le dis-

positif de montage ou la piece à souder doit être branché à

une bonne mise à la terre.

2. Autant que possible, Iʼinstallation et lʼentretien du poste

seront effectués par un électricien qualifié.

3. Avant de faires des travaux à lʼinterieur de poste, la

debrancher à lʼinterrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

LN-7 & LN-7 GMA

vi

TABLE OF CONTENTS

Page

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-iv

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section A

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Machine Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Input Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Work Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21

Gun and Cable Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21

Gun Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21

Water Connections (For Water Cooled Guns) . . . . . . . . . . . . . . . . . . . . . A-22

Shielding Gas Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-23

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section B

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Recommended Processes and Equipment . . . . . . . . . . . . . . . . . . . . . . . B-2

Controls and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3

Avoiding Ground Lead Protector (GLP) Activation . . . . . . . . . . . . . . . . . . B-3

Drive Roll Installation (2 Roll) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3

Drive Roll Installation (4 Roll) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5

Idle Roll Pressure Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

Wire Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8

Acceleration Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12

Wire Speed and Voltage Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12

Making a Weld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-13

Wire Reel Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-13

K417 Digital Voltmeter Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-13

Optional Flux Tank Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-14

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section C

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Auxiliary Equipment Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Options/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Attaching the Wire Reel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section D

Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section E

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section F

Parts Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-283, P-744 Series

A-1

LN-7 & LN-7 GMA

A-1

INSTALLATION

TECHNICAL SPECIFICATIONS – LN-7 and LN-7 GMA

INPUT VOLTAGE

WIRE FEED SPEED

WIRE DIAMETERS

PHYSICAL DIMENSIONS

Supplied by power source: 115 VAC, 50/60 Hz, 2.5 Amps

LN-7 GMA 75 to 700 in. per minute (1.90 to 17.8 m/min)

LN-7 50 to 500 in. per minute (1.27 to 12.7 m/min)

LENGTH

TOTAL WEIGHT

LESS ELECTRODE

24 lbs

(10.9 kg)

0.023 in. through 1/16 in.

solid electrode

(0.6 through 1.6 mm)

LN-7 GMA

0.045 in. through 5/64 in.

cored electrode

(1.2 through 2.0 mm)

0.023 in. through 3/32 in.

solid electrode

(0.6 through 2.4 mm)

LN-7

0.045 in. through 7/64 in.

cored electrode

(1.2 through 2.8 mm)

WIDTH

HEIGHT

TWO

ROLL

FEEDER

WITH WIRE

STAND (K377)

WITHOUT

WIRE STAND

FOUR

ROLL

FEEDER

WITH WIRE

STAND (K377)

WITHOUT

WIRE STAND

36 lbs

(16.3 kg)

30.5 lbs

(13.8 kg)

42.5 lbs

(19.3 kg)

9.62 in.

(244 mm)

20.68 in.

(525 mm)

9.70 in.

(246 mm)

20.76 in.

(527 mm)

9.76 in.

(247 mm)

9.76 in.

(247 mm)

11.60 in.

(295 mm)

11.60 in.

(295 mm)

10.89 in.

(277 mm)

17.00 in.

(432 mm)

11.11 in.

(282 mm)

17.00 in.

(432 mm)

DUTY CYCLE: The amount of welding performed in a 10 minute period, expressed as a percentage.

A-2

INSTALLATION

LN-7 & LN-7 GMA

A-2

MOUNTING LOCATION

The LN-7 and LN-7 GMA wire feeder can be mounted

directly on top of the power source providing that it is

secure and level. It can also be mounted to an

undercarriage when portability is required.

MACHINE GROUNDING

The LN-7 and LN-7 GMA wire feeders are ground to

the power source through the input cable. The power

source grounding terminal must be properly connected

to electrical ground per the power source operating

manual.

INPUT CABLE CONNECTIONS

Various input cable assemblies are available for the

LN-7 GMA wire feeder. Refer to the Accessories

section for complete descriptions

Turn input power off before connecting the LN-7

GMA wire feeder.

------------------------------------------------------------------------

For connecting an LN-7 GMA to a specific Lincoln

power source follow steps 1 through 6, and refer to the

connection diagrams in Figure A.3 through A.17 for the

specific power source. Table A.1 lists each figure

number with its corresponding power source.

Figure # Power Source

A.3 LN-7 GMA To DC-400, DC-250 and CV/CVI Power Sources With Terminal Strip - Connection

Diagram

A.4 LN-7 GMA To Pulsed Power 500 - Connection Diagram

A.5 LN-7 GMA To CV/CVI Power Sources With 14 Pin Amphenol Connector - Connection Diagram

A.6 LN-7 GMA To CV/CVI Power Sources With Twist-Mate Connector and 14 Pin Amphenol/Remote

Control - Connection Diagram

A.7 LN-7 GMA To CV/CVI Power Source (K867/K775) - Connection Diagram

A.8 LN-7 GMA To R3S-250 or R3S-325 - Connection Diagram

A.9 LN-7 GMA To SAM Motor Generator or Engine Welder - Connection Diagram

A.10 LN-7 GMA To DC-600 - Connection Diagram

A.11 LN-7 GMA To R3S-400, 600, or 800 - Connection Diagram

A.12 LN-7 GMA To Most Lincoln Motor Generators - Connection Diagram

A.13 LN-7 GMA To WP250 or G9 PRO - Connection Diagram

A.14 LN-7 GMA To Ranger 9 - Connection Diagram

A.15 LN-7 GMA To Ranger 10-LX - Connection Diagram

A.16 LN-7 GMA To Power Sources With No Output Contactor - Connection Diagram

A.17 LN-7 GMA To Power Sources With Contactor and No Terminal Strip - Connection Diagram

A.18 LN-7 GMA To FLEXTEC 650 - Connection Diagram

TABLE A.1 - LN-7 GMA CONNECTION DIAGRAMS

WARNING

A-3

INSTALLATION

LN-7 & LN-7 GMA

A-3

1. For K291 and K404 cables, connect the end of the

control cable with the lugged leads to the power

source. If lead #21 is extended to work, do not

connect leads to terminal #21 on terminal strip.

For K584, K594 or K480 cables connect the 14

pin amphenol connector to the power source.

Include any jumpers called for on the connection

diagram. Do not add any other jumpers or

connections.

Never operate a Lincoln power source that has a

jumper from #2 to #4 on the terminal strip, or a

power source without a contactor, with this wire

feeder. To do so would defeat the purpose of the

grounding lead protector circuit and could result in

the overheating of the electrical ground circuit to

the wire feeder.

------------------------------------------------------------------------

2. For constant voltage power sources with an

output contactor but no terminal strip or 14-pin

control receptacle, see Figure A.17. For constant

voltage power sources without an internal output

contactor, and requiring a K240 Contactor Kit,

see Figure A.16.

3.

If input cables longer than the standard length

must be used, K292 extension cables (50 ft/15.2

m) can be installed. These have polarized plugs

on each end of the control cable and include a 4/0

(107 mm

2

) electrode cable. Install the extensions

between the standard input cable and the wire

feeder. Total input cable length should not exceed

400 ft (122 m). When using longer lengths of

extension cables, it may be necessary to add

parallel electrode cables to minimize the voltage

drop in the cable.

4. Referring to Figure A.1, route the end of the

electrode cable through the large hole in the back

panel of the LN-7 case. Connect the electrode

cable to the brass conductor block on the front of

the gearbox using the 1/2-13 x .75 bolt provided.

Be sure the cable is placed to allow easy

access and clearance for the idle roll arm

pressure adjustment and to allow the drive

roll section cover to close.

WARNING

CONDUCTOR

BLOCK

ELECTRODE

CABLE

CONTROL

CABLE

FIGURE A.1 – INPUT CONTROL CABLE AND

ELECTRODE CABLE CONNECTIONS.

A-4

INSTALLATION

LN-7 & LN-7 GMA

A-4

5. Connect the input control cable polarized

Amphenol plug into the mating 6-pin receptacle

on the rear of the control section.

6. Referring to Figure A.2, install the input cable

under the wire reel mounting stand strain relief

clamp. Remove the screws holding the clamp to

the base of the wire reel mounting assembly, put

the input cable assembly under the clamp and

reinstall the screws.

STRAIN

RELIEF

CLAMP

CONTROL

CABLE

ELECTRODE

CABLE

FIGURE A.2 – STRAIN RELIEF CLAMP.

A-5

INSTALLATION

LN-7 & LN-7 GMA

A-5

FIGURE A.3 – LN-7 & LN-7 GMA TO DC-400, DC-250 AND CV/CVI POWER SOURCES WITH

TERMINAL STRIP - CONNECTION DIAGRAM.

77

–

+

CLEVELAND, OHIO U.S.A

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE

LN-7 GMA WIRE FEEDER.

WARNING

A-6

INSTALLATION

LN-7 & LN-7 GMA

A-6

FIGURE A.4 – LN-7 & LN-7 GMA TO PULSED POWER 500 - CONNECTION DIAGRAM.

–

+

CLEVELAND, OHIO U.S.A

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE

LN-7 GMA WIRE FEEDER.

WARNING

A-7

INSTALLATION

LN-7 & LN-7 GMA

A-7

FIGURE A.5 – LN-7 & LN-7 GMA TO CV/CVI POWER SOURCES WITH 14 PIN AMPHENOL

CONNECTOR - CONNECTION DIAGRAM.

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE

LN-7 GMA WIRE FEEDER.

WARNING

CLEVELAND, OHIO U.S.A

–

+

A-8

INSTALLATION

LN-7 & LN-7 GMA

A-8

FIGURE A.6 – LN-7 & LN-7 GMA TO CV/CVI POWER SOURCES WITH TWIST-MATE CONNECTOR

AND 14 PIN AMPHENOL/REMOTE CONTROL - CONNECTION DIAGRAM.

CLEVELAND, OHIO U.S.A

–

+

ELECTRIC

SHOCK

CAN KILL

TURN OFF INPUT POWER

TO THE WELDING POWER

SOURCE USING THE

DISCONNECT SWITCH AT

THE FUSE BOX BEFORE

CONNECTING THE WIRE

FEEDER.

WARNING

ONLY QUALIFIED PERSONS

SHOULD INSTALL, USE, OR

SERVICE THIS MACHINE.

A-9

INSTALLATION

LN-7 & LN-7 GMA

A-9

FIGURE A.7 – LN-7 & LN-7 GMA TO CV/CVI POWER SOURCE (K867/K775) - CONNECTION DIAGRAM.

–+

CLEVELAND, OHIO U.S.A

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE

LN-7 GMA WIRE FEEDER.

WARNING

A-10

INSTALLATION

LN-7 & LN-7 GMA

A-10

FIGURE A.8 – LN-7 & LN-7 GMA TO R3S-250 OR R3S-325 - CONNECTION DIAGRAM.

–+

CLEVELAND, OHIO U.S.A

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE 

LN-7 GMA WIRE FEEDER.

WARNING

A-11

INSTALLATION

LN-7 & LN-7 GMA

A-11

FIGURE A.9 – LN-7 & LN-7 GMA TO SAM MOTOR GENERATOR OR ENGINE WELDER - CONNECTION

DIAGRAM.

CLEVELAND, OHIO U.S.A

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE

LN-7 GMA WIRE FEEDER.

WARNING

A-12

INSTALLATION

LN-7 & LN-7 GMA

A-12

FIGURE A.10 – LN-7 & LN-7 GMA TO DC-600 - CONNECTION DIAGRAM.

–

+

CLEVELAND, OHIO U.S.A

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE

LN-7 GMA WIRE FEEDER.

WARNING

A-13

INSTALLATION

LN-7 & LN-7 GMA

A-13

FIGURE A.11 – LN-7 & LN-7 GMA TO R3S-400, 600, OR 800 - CONNECTION DIAGRAM.

CLEVELAND, OHIO U.S.A

ELECTRIC

SHOCK

CAN KILL

TURN INPUT POWER OFF

BEFORE CONNECTING THE

LN-7 GMA WIRE FEEDER.

WARNING

La page charge ...

Lincoln Electric LN-7 Mode d'emploi

Lincoln Electric LN-7 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents