Yamaha ATS-2030 Le manuel du propriétaire

Marque: Yamaha

Modèle: ATS-2030

Catégorie: Équipement musical supplémentaire

Taper: Le manuel du propriétaire

Front Surround System

Système Surround Frontal

(ATS-CU2030+NS-WSW41)

Owner’s Manual

Mode d’emploi

Explanation of Graphical Symbols

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

CAN ICES-3 (B)/NMB-3 (B)

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/

accessories specified by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

specified by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries

Association’s Consumer Electronics

Group want you to get the most out of

your equipment by playing it at a safe

level. One that lets the sound come

through loud and clear without

annoying blaring or distortion – and,

most importantly, without affecting

your sensitive hearing. Since hearing damage from loud

sounds is often undetectable until it is too late, Yamaha

and the Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid prolonged

exposure from excessive volume levels.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with

arrowhead symbol, within an

equilateral triangle, is intended to

alert you to the presence of

uninsulated “dangerous voltage”

within the product’s enclosure that

may be of sufficient magnitude to

constitute a risk of electric shock

to persons.

The exclamation point within an

equilateral triangle is intended to

alert you to the presence of

important operating and

maintenance (servicing)

instructions in the literature

accompanying the appliance.

IMPORTANT

Please record the serial number of this unit in the

space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

CAUTION

RISK OF

ELECTRIC

SHOCK DO

NOT OPEN

• This device complies with Part 15 of the FCC Rules and RSSGen of IC Rules.

• Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this

device must accept any interference received including interference that may cause undesired operation.

See the “Troubleshooting” section at the end of this manual if interference to radio reception is suspected.

FCC WARNING

Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and receiver.

− Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

This equipment compiles with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC

radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment

has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE).

But it is desirable that it should be installed and operated with at least 20 cm and more between the radiator and person’s

body.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY

THIS UNIT!: This product, when installed as

indicated in the instructions contained in this

manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2 IMPORTANT: When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could

void your FCC authorization to use this product in

the USA.

3 NOTE: This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result

in harmful interference with other electronic

devices. This equipment generates/uses radio

frequencies and, if not installed and used according

to the instructions found in the users manual, may

cause interference harmful to the operation of other

electronic devices.

4 Compliance with FCC regulations does not

guarantee that interference will not occur in all

installations. If this product is found to be the source

of interference, which can be determined by turning

the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

5 Relocate either this product or the device that is

being affected by the interference.

6 Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

7 In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to coaxial type

cable.

8 If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you

can not locate the appropriate retailer, please contact

Yamaha Corporation of America A/V Division 6600

Orangethorpe Ave., Buena Park, CA 90620.

9 The above statements apply ONLY to those

products distributed by Yamaha Corporation of

America or its subsidiaries.

Explication des symboles

POUR LES CONSOMMATEURS CANADIENS

Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la

prise et pousser jusqu’au fond.

CAN ICES-3 (B)/NMB-3 (B)

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser cet appareil à proximité de l’eau.

6 Nettoyer cet appareil avec un chiffon sec seulement.

7 Ne pas recouvrir les ailettes de ventilation. Installer

l’appareil selon les instructions du fabricant.

8 Ne pas installer près d’une source de chaleur,

comme un appareil de chauffage, une résistance

électrique, un poêle, ou tout autre appareil

(amplificateurs compris) produisant de la chaleur.

9 Ne pas désamorcer le système de sécurité d’une fiche

polarisée ou d’une fiche avec mise à la terre. Une

fiche polarisée est munie de deux lames, dont l’une est

plus large que l’autre. Une fiche avec mise à la terre

est munie de deux lames et d’une broche de terre. La

lame la plus large ou la troisième broche sont reliées à

la terre pour des raisons de sécurité. Si la fiche fournie

ne s’insère pas dans la prise, s’adresser à un

électricien pour faire remplacer la prise obsolète.

10 Protéger le cordon d’alimentation de sorte qu’il ne

risque pas d’être piétiné ou coincé, surtout au niveau

des fiches, des prises et de sa sortie de l’appareil.

11 Utiliser seulement les fixations

et accessoires spécifiés par le

fabricant.

12 Utiliser seulement le chariot,

socle, trépied, support ou

meuble spécifié par le fabricant

ou vendu avec l’appareil. Si un

chariot est utilisé, faire

attention de ne pas se blesser

ou de le renverser pendant le transport de l’appareil.

13 Débrancher cet appareil pendant les orages électriques,

ou s’il ne doit pas être utilisé pendant un certain temps.

14 Pour toute inspection s’adresser à un personnel

qualifié. Une inspection est nécessaire en cas de

dommage, quel qu’il soit, par exemple cordon

d’alimentation ou fiche endommagé, liquide

répandu ou objet tombé à l’intérieur de l’appareil,

exposition de l’appareil à la pluie ou à l’humidité,

fonctionnement anormal ou chute de l’appareil.

Nous vous souhaitons un plaisir musical durable

Yamaha et le Groupe des Entreprises

Électroniques Grand Public de

l’Association des Industries Électroniques

vous demandent de tirer le meilleur parti

de votre équipement tout en écoutant à un

niveau non dommageable pour l’ouïe,

c’est-à-dire un niveau où vous pouvez

obtenir un son fort et clair, sans hurlement

ni distorsion, mais sans aucun danger pour

l’ouïe. Comme les sons trop forts causent des lésions auditives

qui ne peuvent être détectées qu’à long terme, lorsqu’il est trop

tard, Yamaha et le Groupe des Entreprises Électroniques

Grand Public de l’Association des Industries Électroniques

vous déconseillent l’écoute prolongée à des volumes excessifs.

PRÉCAUTIONS CONCERNANT LA SÉCURITÉ

ATTENTION : POUR RÉDUIRE LES RISQUES

D’INCENDIE ET DE DÉCHARGE ELECTRIQUE,

NE PAS RETIRER LE COUVERCLE (OU LE

PANNEAU ARRIÈRE). AUCUNE PIÈCE

INTERNE NE PEUT ÊTRE CHANGÉE PAR

L’UTILISATEUR. POUR L’ENTRETIEN,

S’ADRESSER À UN PERSONNEL QUALIFIÉ.

L’éclair avec une flèche à

l’intérieur d’un triangle équilatéral

est destiné à attirer l’attention de

l’utilisateur sur la présence d’une

« tension dangereuse » non isolée à

l’intérieur du produit, pouvant être

suffisamment élevée pour

constituer un risque d’électrocution.

Le point d’exclamation à

l’intérieur d’un triangle équilatéral

est destiné à attirer l’attention de

l’utilisateur sur la présence

d’instructions importantes sur

l’emploi ou de la maintenance

(réparation) de l’appareil dans la

documentation fournie.

IMPORTANT

Veuillez enregistrer le numéro de série de cet appareil

dans l’espace réservé à cet effet, ci-dessous.

MODÈLE :

No. de série :

Le numéro de série se trouve à l’arrière de l’appareil.

Prière de conserver le mode d’emploi en lieu sûr pour

toute référence future.

ATTENTION

RISQUE DE

CHOC

ÉLECTRIQUE

NE PAS

OUVRIR

• Cet appareil est conforme à la Partie 15 du Règlement FCC et au RSS-Gen du Règlement IC.

• Le fonctionnement est soumis aux deux conditions suivantes: 1) Cet appareil ne peut pas causer d’interférences nuisibles et

2) Cet appareil doit recevoir toutes les interférences, y compris celles pouvant entraîner des problèmes de fonctionnement.

Consultez le mode d’emploi si vous soupçonnez que la réception radio subit des interférences.

AVERTISSEMENT FCC

Tout changement apporté sans l’approbation expresse du fabricant pourrait entraîner l’annulation du droit d’utilisation de l’appareil.

REMARQUE

Cet appareil a été testé et il s’est avéré être conforme aux limites déterminées pour un appareil numérique de Classe B,

conformément à la partie 15 du Règlement FCC. Ces limites sont destinées à offrir une protection raisonnable contre les

interférences nuisibles pouvant survenir en cas d’utilisation de ce produit dans un environnement domestique.

Cet appareil produit, utilise et peut émettre de l’énergie radioélectrique et, s’il n’est pas installé conformément aux

instructions, peut provoquer des interférences radio. Il n’est toutefois pas garanti qu’aucune interférence ne se produira

dans le cas d’une installation donnée. Si l’appareil provoque des interférences nuisibles à la réception de programmes

radio ou de télévision, ce qui peut être déterminé en éteignant, puis en allumant l’appareil, l’utilisateur est prié de tenter

de corriger le problème en prenant l’une ou plusieurs des mesures suivantes:

− Réorienter ou déplacer l’antenne réceptrice.

− Éloigner davantage l’appareil du récepteur.

− Raccorder l’appareil à une prise d’un circuit différent de celui du récepteur.

− Consulter le revendeur ou un technicien radio/télé expérimenté.

Cet appareil est conforme aux limites FCC/IC d’exposition aux rayonnements définies pour les appareils non

commandés et satisfait aux directives d’exposition aux fréquences radio (RF) FCC et au règlement RSS-102

d’exposition aux fréquences radio (RF) IC. Cet appareil possède des niveaux d’énergie RF très bas, considérés

conformes aux taux d’exposition maximum autorisés (MPE) non contrôlés. Mais il est toutefoispréférable d’installer et

d’utiliser l’appareil en conservant une distance minimum de 20 cm entre l’émetteur et toute personne.

Ce émetteur ne peut pas être placé à proximité de ou utilisé conjointement avec tout autre émetteur ou antenne.

Informations de la FCC (Pour les clients résidents aux États-Unis)

1 AVIS IMPORTANT: NE PAS APPORTER DE

MOFIDICATIONS À CET APPAREIL!

Ce produit est conforme aux exigences de la FCC s’il

est installé selon les instructions du mode d’emploi.

Toute modification non approuvée expressément par

Yamaha peut invalider l’autorisation, accordée par la

FCC, d’utiliser ce produit.

2 IMPORTANT: N’utiliser que des câbles blindés de

haute qualité pour le raccordement de ce produit à

des accessoires et/ou à un autre produit. Seuls le ou

les câbles fournis avec le produit DOIVENT être

utilisés. Suivre les instructions concernant

l’installation. Le non respect des instructions peut

invalider l’autorisation, accordée par la FCC,

d’utiliser ce produit aux États-Unis.

3 REMARQUE:

Ce produit a été testé et déclaré

conforme aux normes relatives aux appareils numériques

de Classe « B », telles que fixées dans l’Article 15 de la

Réglementation FCC. Ces normes sont destinées à

assurer une protection suffisante contre les interférences

nuisibles avec d’autres appareils électroniques dans une

installation résidentielle. Cet équipement génère et utilise

des fréquences radio qui, en cas d’installation et

d’utilisation non conformes aux instructions du mode

d’emploi, peuvent être à l’origine d’interférences

empêchant d’autres appareils de fonctionner.

4 Cependant, la conformité à la Réglementation FCC

ne garantit pas l’absence d’interférences dans une

installation particulière. Si ce produit devait produire

des interférences, ce qui peut être déterminé en

ÉTEIGNANT » et en

RALLUMANT » le

produit, l’utilisateur est invité à essayer de corriger

le problème d’une des manières suivantes:

5 Réorienter ce produit ou le dispositif affecté par les

interférences.

6 Utiliser des prises d’alimentation branchées sur

différents circuits (avec interrupteur de circuit ou

fusible) ou installer un ou des filtres pour ligne secteur.

7 Dans le cas d’interférences radio ou TV, changer de

place l’antenne et la réorienter. Si l’antenne est un

conducteur plat de 300 ohms, remplacer ce câble par

un câble de type coaxial.

8 Si ces mesures ne donnent pas les résultats

escomptés, prière de contacter le détaillant local

autorisé à commercialiser ce type de produit. Si ce

n’est pas possible, prière de contacter Yamaha

Corporation of America A/V Division, États-Unis,

6600 Orangethorpe Ave., Buena Park, CA 90620

9 Les déclarations précédentes NE concernent QUE

les produits commercialisés par Yamaha

Corporation of America ou ses filiales.

iii

• To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

• Install this unit in a well ventilated, cool, dry, clean

place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum

clearances.

Sound bar: Top: 10 cm (4 in), Rear: 10 cm (4 in),

Sides: 10 cm (4 in)

Subwoofer: Top: 20 cm (8 in), Rear: 20 cm (8 in),

Sides: 20 cm (8 in)

• Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

• Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in an environment with high humidity (i.e. a

room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal

injury.

• Avoid installing this unit where foreign objects

may fall onto this unit and/or this unit may be

exposed to liquid dripping or splashing. On the top

of this unit, do not place:

− Other components, as they may cause damage

and/or discoloration on the surface of this unit.

− Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

− Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

• Do not cover this unit with a newspaper,

tablecloth, curtain, etc., in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

• Do not plug in this unit to a wall outlet until all

connections are complete.

• Do not operate this unit upside-down. It may

overheat, possibly causing damage.

• Do not use force on switches, knobs and/or cords.

• When disconnecting the power cable from the wall

outlet, grasp the plug; do not pull the cable.

• Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

• Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. Yamaha will not be

held responsible for any damage resulting from use

of this unit with a voltage other than specified.

• To prevent damage by lightning, keep the power

cable and outdoor antennas disconnected from a

wall outlet or the unit during a lightning storm.

• Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

• When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power

plug from the wall outlet.

• Be sure to read the “Troubleshooting” section on

common operating errors before concluding that

this unit is faulty.

• Before moving this unit, press to set this unit in

standby mode, and disconnect the power supply

cable from the wall outlet.

• Condensation will form when the surrounding

temperature changes suddenly. Disconnect the

power supply cable from the outlet, then leave the

unit alone.

• Install this unit near the wall outlet and where the

AC power plug can be reached easily.

• Secure placement or installation is the owner’s

responsibility. Yamaha shall not be liable for any

accident caused by improper placement or

installation of speakers.

• Do not put a hand or foreign object into the port on

the subwoofer.

• When moving the subwoofer, do not hold the port,

as it may cause personal injury and/or damage to

this unit.

• Do not place a fragile object near the port of the

subwoofer. If the object falls as a result of the air

pressure, it may cause personal injury and/or

damage to the subwoofer and the object.

• Keep the product out of reach of children to avoid

them swallowing small parts.

Notes on remote controls and batteries

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following places:

− places of high humidity, such as near a bath

− places of high temperatures, such as near a

heater or a stove

− places of extremely low temperatures

− dusty places

• Do not expose the remote control sensor of this

unit to direct sunlight or lighting such as inverted

fluorescent lamps.

• If the batteries grow old, the effective operation

range of the remote control decreases

considerably. If this happens, replace the batteries

with two new ones as soon as possible.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as

alkaline and manganese batteries) together. Read

the packaging carefully as these different types of

batteries may have the same shape and color.

• Exhausted batteries may leak. If the batteries have

leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery

compartment thoroughly before installing new

batteries.

• Do not carry batteries in a pocket or purse with

metal objects like coins, etc.

• Do not throw away batteries with general house

waste. Dispose of them correctly in accordance

with your local regulations.

• Keep batteries away from children. If a battery is

accidentally swallowed, contact your doctor

immediately.

• When not planning to use the remote control for

long periods of time, remove the batteries from the

remote control.

• Do not charge or disassemble the supplied

batteries.

• The batteries shall not be exposed to excessive

heat such as sunshine, fire or like.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

As long as this unit is connected to the AC wall

outlet, it is not disconnected from the AC power

source even if you turn off this unit by . In this

state, this unit is designed to consume a very

small quantity of power.

(Power key)

Turns on the power of this unit or sets it to the

standby mode.

Do not use this unit within 22 cm (9 inches) of

persons with a heart pacemaker implant or

defibrillator implant.

Radio waves may affect electro-medical devices.

Do not use this unit near medical devices or

inside medical facilities.

The name plate is located on the bottom of the

unit.

Contents

Supplied items ...................................................................... 2

Features................................................................................. 3

Frequently asked questions................................................. 3

Part names and functions (sound bar/subwoofer) ............ 4

Installation ............................................................................ 5

Connections .......................................................................... 6

Operations............................................................................. 8

Listening to the sound from a Bluetooth device .............. 10

Settings................................................................................ 12

Programming the sound bar with the TV’s remote control

(TV’s remote control learning function)..................................................... 12

Sending the TV’s remote signal through the sound bar

(TV Remote Repeater function)......................................................................... 14

Setting the auto power standby function ................................................ 14

Initializing the sound bar ................................................................................ 14

Troubleshooting ................................................................. 15

Specifications...................................................................... 20

About this manual

NOTE

This indicates precautions for use of the product and its feature limitations.

HINT

This indicates supplementary explanations for better use.

Supplied items

Make sure you have received all of the following items.

How to use the remote control

Preparing the remote control

Peel off the protection sheet before use.

Operating range of the remote control

Remain within the operating range shown below.

Remote control

Sound bar (ATS-CU2030)

Wireless subwoofer

(NS-WSW41)

Mounting template

* Using when attaching the sound bar to a wall

Stand x 2

(For sound bar)

Battery x 2

(AAA, R03, UM4)

Screw x 2

(For attaching

the stand)

Quick Start Guide

Optical cable (1.5 m [4.9 ft])

RCA stereo cable (1.5 m [4.9 ft])

Owner’s Manual

(This manual)

Remote control sensor

Within 6 m

(20 ft)

Features

Enjoy powerful and realistic sound from the front surround system

consisting of the sound bar and wireless subwoofer, and easy

installation and connection to TVs and other devices.

Frequently asked questions

The following section covers popular functions and frequently asked questions about the

sound bar.

•AIR SURROUND XTREME

Enjoy 7.1 channel surround sound, which creates a wide and deep soundstage, as

if speakers are set, not only on the front, but also on the left and right, and behind

the listener (p.9).

• Advanced Bass Extension Processing

Equipped with Yamaha’s original bass boost technology, this system reproduces

more powerful sound from the dedicated subwoofer (p.9).

• Bluetooth® connection

Content on a Bluetooth compatible smartphone, tablet, or computer can be played

back easily (p.10).

You can enjoy deep and fresh sound as close to the original by the Compressed

Music Enhancer. The sound bar is also compliant with the aptX codec, which

enables you to enjoy better sound from your smartphone.

• HOME THEATER CONTROLLER

You can operate the sound bar easily by installing the dedicated controlling

application “HOME THEATER CONTROLLER.”

• TV’s remote control learning function

Operate the sound bar with the TV’s remote control (p.12).

• TV Remote Repeater function

Enables the TV’s remote signal to pass through the sound bar. If the installed

sound bar blocks the TV’s remote sensor, the TV’s remote will not work. This

function provides a convenient solution (p.14).

•Clear voice

Makes voice sound (such as dialogues and narrations) clear (p.9).

•UniVolume

Maintains consistent sound volume when inputs or sound sources switch (p.9).

Can I operate the sound bar using the remote control of the TV?

Switching between the remote controls of the TV and sound bar is

inconvenient.

Yes. You can control the sound bar using your TV’s remote control by the

“TV’s remote control learning” function (p.12).

This function is available only for the IR (infrared) remote control. Check your

TV’s remote control type.

The TV’s remote control does not work after the sound bar is installed in

front of the TV.

If your TV’s remote control uses IR (infrared) signals, set the “TV Remote

Repeater” function to transmit the TV’s remote control signals from the sound

bar (p.14).

If your TV’s remote control uses radio waves, increase the distance between

the TV and sound bar.

Can I make voice sound more clearly?

Yes. Dialogue in movies, TV news or sports programs, etc., can be made

clearer using the “clear voice” function (p.9).

Part names and functions (sound bar/subwoofer)

Sound bar (front panel)

A Indicators

Indicate the status of the sound bar. The indicators will dim automatically if no

operations are performed for 5 seconds. Refer to “Operations” (p.8 to 9) and

“Wireless connection with the subwoofer” (p.7) for the main functions of the

indicators.

B Remote control sensor

Receives infrared signals from the remote control of the sound bar (p.2).

C TV’s remote control sensor

Receives infrared signals from the TV’s remote control when the TV Remote

Repeater function is enabled (p.14).

D INPUT key

Selects an input source to be played back (p.8).

E MUTE key

Mutes the audio output. Press the key again to unmute (p.9).

F VOLUME (+/–) keys

Adjust the volume (p.8).

G (power) key

Turns on or off (standby) the sound bar (p.9).

HINT

• The sound bar may automatically turn off when the auto power standby function is enabled (p.14).

H Speakers

Sound bar (rear panel)

A TV input jack

For connecting to a TV with an optical cable (p.6).

B BD/DVD input jack

For connecting to a playback device, such as a Blu-ray Disc (BD) player, with a

coaxial digital cable (p.6).

C ANALOG input jacks

For connecting an external device with an RCA stereo cable (p.7).

D IR flasher for TV Remote Repeater

Transmits TV’s remote control signals received at the TV’s remote control sensor to

the TV (p.14).

Subwoofer (rear panel)

A STATUS indicator

Indicates the status of the subwoofer

(p.9).

B SUBWOOFER PAIRING button

For setting wireless connection

between the sound bar and

subwoofer (p.19).

C Port

Installation

Place the sound bar on a flat surface such as on top of a

TV cabinet.

Place the subwoofer to the outside of the sound bar.

To avoid echoes from the wall, face the front side of the

subwoofer slightly inward.

HINT

• If it is difficult to operate the TV, use the TV Remote Repeater

function (p.14) to transmit the TV’s remote control signal via sound

bar.

• When placing the sound bar across the bases of the TV, or when

changing the height of the sound bar, attach the supplied stands

with the stand attachment screws.

Attaching the sound bar to a wall

How to install on the wall

1 Attach the mounting template on a wall and mark

for the screw holes.

2 Remove the mounting template from the wall,

then install commercially available screws (as

illustrated below) at the points marked on the

wall.

3 Hang the sound bar on the screws.

Cautions

• Do not stack the sound bar/subwoofer and a BD player or other

device directly on each other. Doing so may cause a malfunction

due to vibrations.

• Do not hold the speaker portion (fabric part) on the front of the

subwoofer when moving it.

• The sound bar contains non-magnetic shielding speakers. Do not

place magnetically sensitive items (hard disk drive, etc.) near the

sound bar.

• Depending on your installation environment, it may be better to

connect the sound bar and external devices (such as a TV)

before installing the sound bar.

• Do not place the sound bar within 50 mm (2") of the TV.

• The subwoofer and sound bar communicate wirelessly. Do not

place objects that block wireless signals, such as metallic

furniture and devices, between the subwoofer and sound bar as

the wireless communication may be adversely affected.

• If the subwoofer is covered with a cloth or other object, the sound

volume is reduced. Install the subwoofer so that it is not hidden

behind a thick curtain, etc.

Cautions

• When installing the sound bar on a wall, all installation work must

be performed by a qualified contractor or dealer. The customer

must never attempt to perform this installation work. Improper or

inadequate installation could cause the sound bar to fall,

resulting in personal injury.

• Do not attach the sound bar to a wall that is made of weak

materials such as plaster or veneered woods. Doing so may

cause the sound bar to fall.

• Make sure you use commercially available screws that can

support the weight of the installation (specified in Step 2 on the

right). Using clamps other than specified screws, such as short

screws, nails, and two-sided tape, may cause the sound bar to

fall.

Cautions

• Fix the cables in place where they will not become loose. If your

foot or hand accidentally gets caught on a loose cable, the sound

bar may fall.

• Check that the sound bar is fixed securely after the installation.

Yamaha will bear no responsibility for any accidents caused by

improper installations.

Tapes or thumbtacks

Mounting template (supplied)

Screw

holes

7 to 8.5 mm

(1/4" to 5/16")

3 to 4 mm (1/8" to 3/16")

4 mm (#8)

20 mm (3/4")

or more

Mounting holes

on rear of sound bar

Connections

Power cable

To AC wall outlet

Sound bar (rear)

Optical cable

Coaxial digital cable

(commercially available)

Playback device (such as a BD player)

Set top box

OPTICAL OUTPUT

Coaxial digital

audio output

(orange)

HINT

If your playback device has a coaxial digital

audio output, you can connect it to the BD/

DVD input of the sound bar with a coaxial

digital cable (commercially available).

Connect to a TV (or other peripheral device).

HINT

• If a setting to disable the speaker output is not available on your TV, you may disable it

by connecting headphones to the headphone jack on the TV. For details, refer to the

manuals of the TV.

• The TV and BD/DVD input jacks support the following audio signals.

− PCM (2 channel)

− Dolby Digital (up to 5.1 channel)

− DTS Digital Surround (up to 5.1 channel)

Cautions

• Make sure that the power cables of the sound bar and subwoofer are not connected

to AC wall outlets when you start making connections.

• Do not use excessive force when inserting the cable plug. Doing so may damage the

cable plug or terminal.

1 Connect the TV and sound bar with the optical

cable (supplied).

Remove the cap of the optical cable and check the

direction of the plug.

2 Connect the power cables of the sound bar and

subwoofer to AC wall outlets.

3 Set the TV as follows.

• Set the TV volume to minimum.

• Disable the TV built-in speaker output (if available).

HDMI cable (etc.)

Subwoofer (rear)

Power cable

To AC wall outlet

Analog connection of an external device (game

console)

You can connect an external device, such as a game console or TV that does not have

an optical output, to the ANALOG input jacks of the sound bar.

NOTE

• Make sure the left (L) and right (R) channels are connected correctly.

• Select the ANALOG key on the remote control for the input source.

Wireless connection with the subwoofer

When the power cables of the sound bar and subwoofer are connected to AC wall

outlets (p.6) and the sound bar is turned on, the sound bar and subwoofer are

connected automatically. When the connection is complete, the SUBWOOFER indicator

on the sound bar lights up and the sound bar is ready for playback.

HINT

• When the sound bar is turned on for the first time, if the SUBWOOFER indicator on the sound bar does not

light up, see “Pairing the sound bar and subwoofer manually” (p.19) and connect the sound bar and

subwoofer manually.

• Once connected, the sound bar operates with the same subwoofer from the next time it is turned on.

RCA stereo cable (supplied) (etc.)

Game console (etc.)

Subwoofer indicator: Lights up

Operations

Indicators

The indicators on the front panel flash or light up, to

indicate the operation and setting status.

In this manual, illustrations of the nine in-line indicators

are used for explanation.

: Off

: Lights up

: Flashes

(Example: When the STATUS indicator flashes and the TV indicator

lights up)

Input keys

Select an input source to be played back.

TV ....................TV audio

BD/DVD...........Audio from a device connected to

the BD/DVD input jack

ANALOG .........Audio from a device connected to

the ANALOG input jack

BLUETOOTH...Audio from a Bluetooth connected

device

The indicator for the selected input source lights up.

(Example: when TV is selected)

HINT

• To play audio of the playback device connected to the TV or

to watch videos of the playback device, set the TV’s input

source to the playback device.

• For details on Bluetooth connection, refer to “Listening to the

sound from a Bluetooth device” (p.10).

SUBWOOFER keys (+/–)

Adjust the volume of the subwoofer.

VOLUME keys (+/–)

Adjust the volume of the sound bar.

Volume down (–) Volume up (+)

LEARN key

★

Sets the sound bar to the TV’s remote control

learning mode (p.12).

REPEATER key

★

Enables/disables the TV Remote Repeater

function (p.14).

Remote control signal transmitter

Transmits infrared signals.

★: Keys that require pressing for more than 3 seconds

BLUETOOTH STANDBY, SUBWOOFER PAIRING,

AUDIO DELAY, LEARN, REPEATER

★

(power) key

Turns on or off (standby) the sound bar.

The STATUS indicator on the sound bar

The STATUS indicator on the subwoofer

BLUETOOTH STANDBY key

★

Enables/disables the Bluetooth standby mode

(p.11).

SUBWOOFER PAIRING key

★

Performs pairing between the sound bar and

subwoofer (p.19).

Green (turned on)

Red (Bluetooth standby) (p.11)

Off (turned off)

Green (turned on)

Red (turned off)

SURROUND and STEREO keys

Switch between surround and stereo

(2 channel) playback. When surround playback is

selected, you can enjoy a realistic sound effect

using Yamaha’s exclusive AIR SURROUND

XTREME.

HINT

• When 2 channel stereo signals are played in surround,

the PLII indicator lights up.

Lights up (surround playback)

Off (stereo playback)

SURROUND

STEREO

Lights up (Dolby Pro Logic II)

BASS EXTENSION key

Enables/disables the bass extension function.

When this function is enabled, you can enjoy

powerful sound during surround playback through

Yamaha’s exclusive bass boost technology.

Flash 3 times (enabled), flash once (disabled)

MUTE key

Mutes the audio output. Press the key again

to unmute.

Flash (on mute)

CLEAR VOICE key

Enables/disables the clear voice function.

When this function is enabled, you can enjoy clear

voice sounds while watching movies, TV dramas,

news programs or sports programs.

UNIVOLUME key

Enables/disables the UniVolume function.

When this function is enabled, consistent volume is

maintained when inputs or sound sources switch.

HINT

• The UniVolume function is automatically disabled when

BLUETOOTH is selected as the input source.

AUDIO DELAY key

★

Adjusts the audio delay to synchronize the sound

with the video when the video image on the TV

may seem delayed with respect to the sound.

Follow the procedure below to adjust the audio delay.

1 Hold down the AUDIO DELAY key for more

than 3 seconds.

The left most indicator flashes.

2 Press the SUBWOOFER (+/–) key to adjust

the audio delay.

Pressing the SUBWOOFER (+) key delays the

audio output timing.

3 To finish the adjustment, press the AUDIO

DELAY key.

HINT

• The adjustment will be finished automatically if no

operations are performed for 20 seconds.

Flash 3 times (enabled), flash once (disabled)

(–) (+)

Decoder indication

The sound bar supports the following audio signals. You

can check the type of the input audio signal by the color

of the indicator.

Green (Dolby Digital), Red (DTS Digital Surround)

Off (PCM)

Listening to the sound from a

Bluetooth device

You can play back wirelessly from Bluetooth devices, such as smartphones or digital

music players.

See also the operating manual of the Bluetooth device for more details.

Pairing a Bluetooth device with the sound bar

When connecting to a Bluetooth device for the first time, “pairing” between the device

and sound bar is required. “Pairing” is necessary for each Bluetooth device you use.

Once “pairing” with a device is completed, subsequent connection with that device will

not require “pairing.”

1 Press the BLUETOOTH key on the sound bar’s remote control to

select Bluetooth as the input source.

The BLUETOOTH indicator on the front panel lights up in green.

2 Turn on the Bluetooth function of the device to be paired, and

perform pairing.

The operation varies depending on the device. Refer to the operation manual of the

device.

3 Select “ATS-2030 Yamaha” in the Bluetooth device list on the device.

If a passkey (PIN) is required, enter the number “0000.”

When pairing is completed, or a completion message appears on the device.

NOTE

• Perform pairing with the Bluetooth device and sound bar within 10 meters (33 ft) of each other.

• Up to eight Bluetooth devices can be paired with the sound bar. If a ninth device is paired, the oldest

pairing information is deleted.

• If pairing information for a device is deleted, to use that device again, pairing of the device is required

again.

• If a Bluetooth device is already connected to the sound bar, terminate that Bluetooth connection (p.11),

then perform pairing with the new device.

• Refer to “Bluetooth” (p.18) in “Troubleshooting” if pairing cannot be achieved.

Perform the following steps to use a Bluetooth device with the sound bar.

Bluetooth devices

Playing back audio from a Bluetooth device

on the sound bar

For the first Bluetooth

connection

Pairing a Bluetooth device

with the sound bar

For subsequent

Bluetooth connection

Lights up

Playing back audio from a Bluetooth device on the

sound bar

1 With the sound bar turned on, press the BLUETOOTH key on the

sound bar’s remote control to select Bluetooth as the input source.

The BLUETOOTH indicator on the front panel lights up in green.

2 Turn on the Bluetooth function of the device.

When Bluetooth connection is made correctly, the BLUETOOTH indicator of the

sound bar flashes 3 times.

3 Play back a song on the device.

NOTE

• Perform Bluetooth connection with the device and sound bar within 10 meters (33 ft) of each other.

• It may be necessary to select “ATS-2030 Yamaha” in the Bluetooth device list again, in the event that a

connection problem occurs. You may have to change the output setting to output audio to the sound bar,

depending on the Bluetooth device you are using.

• Adjust the volume level of the Bluetooth device as required.

• If a Bluetooth device is already connected to the sound bar, terminate that Bluetooth connection, then

connect with the new device.

Terminating Bluetooth connection

Bluetooth connection is terminated in the following cases. When the sound bar is turned

on and the Bluetooth connection is terminated, the BLUETOOTH indicator flashes once.

• The Bluetooth function is turned off on the compatible device.

• The BLUETOOTH key on the sound bar’s remote control is pressed for more than 3 seconds.

• The sound bar is turned off.

Using the Bluetooth standby mode

The Bluetooth standby mode allows you to turn on (or off) the sound bar automatically,

that interlocked by the operation of the Bluetooth device.

1 With the sound bar turned on, hold down the BLUETOOTH STANDBY

key on the sound bar’s remote control for more than 3 seconds.

Holding down the BLUETOOTH STANDBY key for 3 seconds each time toggles the

mode between enabled and disabled.

When the Bluetooth standby mode is enabled and the sound bar is turned off, the

STATUS indicator lights up in red. (Bluetooth standby)

Using the HOME THEATER CONTROLLER application

By installing the dedicated free application “HOME THEATER CONTROLLER” to a

Bluetooth device, such as a smartphone, you can perform various operations easily and

conveniently with the Bluetooth device.

(Setting items: basic operation, sound-field, sound adjustments)

For details on “HOME THEATER CONTROLLER,” see the product information on our

website.

Lights up

Flashes 3 times

Functions available on Bluetooth devices with Bluetooth standby mode enabled

Power on interlock function (when the sound bar is turned off)

When Bluetooth connection is made on the device, the sound bar will turn on and will be ready to play

back sound from the device.

Power off interlock function (when the sound bar is turned on)

The sound bar will be turned off when Bluetooth connection is terminated on a Bluetooth device. (Only

when BLUETOOTH is selected as the input source.)

Flash 3 times (enabled), flash once (disabled)

Lights up (red)

Settings

Once you program the sound bar, you can control it with your TV’s remote control for

functions such as turning on/off the TV and sound bar simultaneously, or volume up/

down and muting/unmuting of the sound bar.

1 Turn off the TV.

2 Turn off the sound bar.

3 Hold down the LEARN key on the sound bar’s remote control for

more than 3 seconds to set the sound bar to the learning mode.

When the sound bar is in the learning mode, the indicators on the front panel flash

as shown below.

NOTE

• Steps 4 to 7 require only the TV’s remote control and the keys on the front panel of the sound bar.

The remote control of the sound bar is not necessary.

• If the sound bar has already learned functions, the following indicators light up.

Mute: BD/DVD, Volume (–): ANALOG, Volume (+): BLUETOOTH, Power: SURROUND

4 Teach the sound bar the “Mute” code of the TV’s remote control.

4-1 Press MUTE on the front panel of the sound bar.

4-2 While pointing your TV’s remote control at the remote control sensor, hold

down the mute key for more than 1 second twice or three times.

5 Teach the sound bar the “Volume (–)” code of the TV’s remote

control.

5-1 Press VOLUME (–) on the front panel of the sound bar.

5-2 While pointing your TV’s remote control at the remote control sensor, hold

down the volume (–) key for more than 1 second twice or three times.

Programming the sound bar with the TV’s remote

control (TV’s remote control learning function)

• This function is available only when your TV’s remote control uses IR (infrared) signal.

• An RF (Radio Frequency) remote control will not work.

• If you want to use a cable or satellite set top box’s remote control to operate the sound bar, use your

original TV’s IR (infrared) remote control to program the sound bar, then use the set top box’s remote

control to operate.

• If by changing the volume of the sound bar the TV’s volume also changes, set the TV’s volume to

minimum, or disable speaker output.

Result Bleep/buzzer Indicators

Successfully

learned

Once

Failed to learn

* Repeat from

Step 4-1.

Twice

Result Bleep/buzzer Indicators

Successfully

learned

Once

Failed to learn

* Repeat from

Step 5-1.

Twice

Approx. 30 cm (1 ft)

TV’s remote control

Hold down

(more than 1 second)

Release

(more than 1 second)

Hold down

(more than 1 second)

Release

(...)

Lights up

Flash

Lights up

Flash

6 Teach the sound bar the “Volume (+)” code of the TV’s remote control.

6-1 Press VOLUME (+) on the front panel of the sound bar.

6-2 While pointing your TV’s remote control at the remote control sensor, hold

down the volume (+) key for more than 1 second twice or three times.

7 Teach the sound bar the “Power” code of the TV’s remote control.

7-1 Press (power) on the front panel of the sound bar.

7-2 While pointing your TV’s remote control at the remote control sensor, hold

down the power key for more than 1 second twice or three times.

8 To finish the learning mode, press the LEARN key on the sound bar’s

remote control.

This completes the necessary settings. Now you can operate the sound bar with

the TV’s remote control’s mute key, volume keys, or power key.

HINT

• The learning mode will be finished automatically if no operations are performed for 5 minutes.

• Set the TV volume to minimum. When you turn up the volume of the sound bar with the TV’s remote

control, the volume of the TV may be turned up at the same time. In this case, follow Step 3 in

“Connections” (p.6) to change the TV setting.

• You can press the (power) key on the sound bar’s remote control to finish learning mode.

Clearing all programmed functions

1 With the sound bar turned off, hold down the LEARN key on the

sound bar’s remote control for more than 3 seconds (for entering the

learning mode).

When the sound bar is in the learning mode, the indicators on the front panel flash

as shown below.

2 Hold down INPUT on the front panel of the sound bar for more than 3

seconds.

If the clearing is completed, you will hear the bleep sound three times.

3 Press the LEARN key on the sound bar’s remote control.

Result Bleep/buzzer Indicators

Successfully

learned

Once

Failed to learn

* Repeat from

Step 6-1.

Twice

Result Bleep/buzzer Indicators

Successfully

learned

Once

Failed to learn

* Repeat from

Step 7-1.

Twice

Lights up

Flash

Lights up

Flash

Flashes in red (cleared)

When the TV Remote Repeater function is enabled, the sound bar relays the TV’s

remote signal received by the front sensor to the rear transmitter. This function should

be enabled when you place the sound bar in front of your TV and you cannot operate

your TV with the TV’s remote control.

1 Turn on the sound bar.

2 Hold down the REPEATER key on the sound bar’s remote control for

more than 3 seconds to enable/disable the TV Remote Repeater

function.

This completes the necessary settings. When the TV Remote Repeater function is

enabled, you can operate your TV from the TV’s remote control via the sound bar.

HINT

• The TV Remote Repeater function is disabled by default.

• If the power cable of the sound bar is connected to an AC wall outlet and when the TV Remote

Repeater function is enabled, the function is usable even when the sound bar is turned off.

• If you have made the sound bar learn the volume (+) operation (p.13), the volume of the TV may be

turned up when you turn up the volume of the sound bar with the TV’s remote control. In this case,

follow Step 3 in “Connections” (p.6) to change the TV setting.

• You can check the status of the TV Remote Repeater function by the SURROUND indicator when

turning on the sound bar.

By enabling the auto power standby function, you can avoid forgetting to turn off the

sound bar after use, or if you fall asleep while watching TV.

NOTE

• When the auto power standby function is enabled and one of the following conditions is met, the sound bar

will automatically turn off.

− No operation for 8 hours

− No audio input and no operations for 20 minutes when BLUETOOTH is selected as the input source.

1 With the sound bar turned off, hold down the MUTE key on the sound

bar’s remote control for more than 3 seconds to enable/disable the

auto power standby function.

You can check the status of the auto power standby function with the TV indicator

when turning on the sound bar.

HINT

• Initial setting varies depending on the country or region.

− U.K. and Europe models: enabled

− Other models: disabled

Follow the procedure below to initialize the sound bar.

1 Turn off the sound bar.

2 Hold down (power) on the front panel of the sound bar for more

than 3 seconds.

Sending the TV’s remote signal through the sound

bar (TV Remote Repeater function)

This function is available only when your TV’s remote control uses infrared signals.

IR flasher for TV Remote Repeater

TV’s remote control sensor

TV’s remote control

Flash 3 times (enabled), flash once (disabled)

Off (enabled), lights up (disabled)

Setting the auto power standby function

Initializing the sound bar

Off (enabled), lights up (disabled)

Flash (initialized)

Troubleshooting

Refer to the table below when the sound bar does not function properly. If the problem

you are experiencing is not listed below or if the instructions below do not help, turn off

the sound bar, disconnect the power cable, and contact the nearest authorized Yamaha

dealer or service center.

First, check the following:

A The power cables of the sound bar, subwoofer, TV and playback devices (such

as BD players) are connected to AC wall outlets securely.

B The sound bar, TV and playback devices (such as BD players) are turned on.

C The connectors of each cable are securely inserted in to jacks on each device.

Power and system

Audio

Problem Cause Remedy

The power turns

off suddenly.

The auto power standby function

worked.

When the auto power standby

function is enabled and one of the

following conditions is met, the

sound bar will automatically turn

off.

- No operation for 8 hours

- No audio input and no

operations for 20 minutes when

BLUETOOTH is selected as the

input source.

Turn on the sound bar again. To stop

the sound bar from turning off

automatically, disable the auto power

standby function (p.14).

The protection circuitry has been

activated. (The STATUS indicator

on the front panel of the sound

bar flashes.)

After confirming that all connections

are made properly, turn on the sound

bar again. If the power still turns off

suddenly or cannot be turned on,

unplug the power cable from the AC

wall outlet and contact the nearest

authorized Yamaha dealer or service

center.

Bluetooth connection is

terminated on a Bluetooth device

when the Bluetooth standby mode

is enabled.

Disable the Bluetooth standby mode

(p.11).

The power

cannot be turned

on.

The protection circuitry has been

activated three times

consecutively. (If you try to turn on

the power in this condition, the

STATUS indicator on the front

panel of the sound bar flashes.)

To protect the product, the power

cannot be turned on. Unplug the

power cable from the AC wall outlet

and contact the nearest authorized

Yamaha dealer or service center.

The sound bar is

not responding

correctly.

The internal microcomputer is

frozen, due to an external electric

shock (such as lightning or

excessive static electricity) or to a

drop in the power supply voltage.

Hold down (power) on the front

panel of the sound bar for more than

10 seconds to reboot it. (If the problem

persists, disconnect the power cable

from the AC wall outlet and plug it

again.)

The sound bar

operates by

itself.

Another Bluetooth device is being

operated nearby.

Terminate Bluetooth connection of the

sound bar (p.11).

TV’s 3D glasses

do not work.

The sound bar is blocking the 3D

glasses transmitter of your TV.

Check the position of the 3D glasses

transmitter of your TV and adjust the

position of the sound bar. Remove the

stands of the sound bar if they are

attached (p.5).

Problem Cause Remedy

No sound.

Another input source is selected. Select an appropriate input source

(p.8).

The mute function is activated. Cancel the mute function (p.9).

The volume is too low. Turn up the volume (p.8).

The power cables of the sound

bar and subwoofer are not

connected properly.

Make sure that power cables of the

sound bar and subwoofer are

connected to AC wall outlets securely

(p.6).

No sound is

coming from the

subwoofer. (The

SUBWOOFER

indicator on the

front panel of the

sound bar is

flashing.)

The subwoofer is not connected

to an AC wall outlet. (The

STATUS indicator on the

subwoofer is not lit.)

Plug in the power cable of the

subwoofer to an AC wall outlet.

The sound bar and subwoofer are

not connected due to a bad

wireless communication status.

(The STATUS indicator on the

subwoofer continues to be lit in

red or flash in green.)

Move the subwoofer closer to the

sound bar. If the situation does not

improve, move the subwoofer to a

location with better communication.

If the communication between the

sound bar and subwoofer is obstructed

by a metallic object or another object,

change the position of the sound bar

and subwoofer or change the

installation location of the subwoofer.

If there is a device (microwave oven,

wireless LAN, etc.) that emits radio

frequency signals, move the sound bar

and subwoofer away from the device.

The sound bar and subwoofer are

not paired. (The STATUS

indicator on the subwoofer is

flashing or lit in red.)

Perform the pairing between the sound

bar and subwoofer (p.19).

If the SUBWOOFER indicator on the

sound bar still does not light up in

green after the pairing is performed, a

malfunction might have occurred.

Unplug the power cables from the AC

wall outlets and contact the nearest

authorized Yamaha dealer or service

center.

The protection circuitry in the

subwoofer has been activated.

(The STATUS indicator on the

subwoofer is lit in orange.)

To protect the product, the power of

the subwoofer cannot be turned on.

Unplug the power cable from the AC

wall outlet and contact the nearest

authorized Yamaha dealer or service

center.

The sound from

the subwoofer is

interrupted. (The

SUBWOOFER

indicator on the

sound bar

flashes when the

sound is

interrupted.)

The connection between the

sound bar and subwoofer is

interrupted due to a bad wireless

communication status. (The

STATUS indicator on the

subwoofer flashes in green when

the sound is interrupted.)

Move the subwoofer closer to the

sound bar. If the situation does not

improve, move the subwoofer to a

location with better communication.

If the communication between the

sound bar and subwoofer is obstructed

by a metallic object or another object,

change the position of the sound bar

and subwoofer or change the

installation location of the subwoofer.

If there is a device (microwave oven,

wireless LAN, etc.) that emits radio

frequency signals, move the sound bar

and subwoofer away from the device.

No sound is

coming from the

subwoofer or the

sound is small.

(The

SUBWOOFER

indicator on the

sound bar is lit.)

The volume is too low. Turn up the volume of the subwoofer

(p.8).

The front side of the subwoofer is

blocked.

Clear the area around the front side

and the port of the subwoofer.

The playback source does not

contain low-frequency signals.

Play back a sound source containing

low-frequency signals, and confirm

that the sound is output from the

subwoofer.

The protection circuitry in the

subwoofer has been activated.

(The STATUS indicator on the

subwoofer is lit in orange.)

To protect the product, the power of

the subwoofer cannot be turned on.

Unplug the power cable from the AC

wall outlet and contact the nearest

authorized Yamaha dealer or service

center.

The volume

decreases when

the sound bar is

turned on.

The automatic volume adjustment

function worked. To prevent

excessive loudness, the sound

bar automatically controls its

volume within a certain level when

the sound bar is turned on.

If necessary, turn up the volume (p.8).

No surround

effect.

Stereo playback is selected. Select surround playback (p.9).

The volume is too low. Turn up the volume (p.8).

The TV or playback device is set

to output 2 channel audio (such

as PCM) only.

Change the digital audio output setting

on the TV or playback device to Dolby

Digital or BitStream.

The audio is output from the TV

built-in speakers.

Set the TV volume to minimum (p.6).

The playback source does not

contain surround audio.

Play back a source that contains audio

recorded in surround.

Noise is heard.

The sound bar is too close to

another digital or high-frequency

device.

Move those devices away from the

sound bar.

La page charge ...

Yamaha ATS-2030 Le manuel du propriétaire

Marque: Yamaha

Modèle: ATS-2030

Catégorie: Équipement musical supplémentaire

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Yamaha ATS-2030 Owner's manual

Yamaha ATS-2030 Le manuel du propriétaire

Yamaha ATS-2030 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents