Whirlpool WTW5000DW Mode d'emploi

Marque: Whirlpool

Modèle: WTW5000DW

Catégorie: Machines à laver

Taper: Mode d'emploi

W10607415B

W10607420A-SP

Designed to use only HE High Efciency

detergents.

Conçue pour l’utilisation d’un détergent haute

efcacité seulement.

Top-Loading

High Efficiency

Low-Water Washer

Use and Care Guide

Table of Contents

WASHER SAFETY .............................................................2

WHAT’S NEW UNDER THE LID? .....................................3

CONTROL PANEL AND FEATURES ................................4

CYCLE GUIDE ...................................................................6

USING YOUR WASHER ....................................................7

WASHER MAINTENANCE ...................................................10

TROUBLESHOOTING ...........................................................12

WARRANTY ............................................................................... 17

ASSISTANCE OR SERVICE ........................ BACK COVER

Table des matières

SÉCURITÉ DE LA LAVEUSE ..........................................18

QUOI DE NEUF SOUS LE COUVERCLE? .....................19

TABLEAU DE COMMANDE ET

CARACTÉRISTIQUES ..................................................... 20

GUIDE DE PROGRAMMES ............................................21

UTILISATION DE LA LAVEUSE ......................................23

ENTRETIEN DE LA LAVEUSE ........................................26

DÉPANNAGE ...................................................................28

GARANTIE ...............................................................................34

ASSISTANCE OU SERVICE. .....COUVERTURE ARRIÈRE

Guide d’utilisation et

d’entretien de la laveuse

haute efficacité à faible

consommation d’eau

avec chargement par

le dessus

Para una versión de estas instrucciones en español, visite www.whirlpool.com

Washer Safety

For best performance, it is recommended to load items in loose

heaps evenly around the washplate.

As the washer dampens and moves the load, the level of the

items will settle in the basket. This is normal, and does not

indicate that more items should be added.

IMPORTANT: You will not see a washer basket full of water

as with your past agitator-style washer. It is normal for some

of the load to be above the water line.

What’s New Under the Lid?

Choosing the Right Detergent

Use only High Efciency detergents. The package will be

marked “HE” or “High Efciency.” Low-water washing creates

excessive sudsing with a regular non-HE detergent. Using

regular detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

failures and noticeable mold or mildew. HE detergents are made

to produce the right amount of suds for the best performance.

Follow the manufacturer’s instructions to determine the amount

of detergent to use.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds and

noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the cycle, as the lid lock goes through a self-test. There

will be different kinds of humming and whirring sounds as the

washplate moves the load and as basket is decelerating to

a stop. And sometimes, you may hear nothing at all, as the

washer determines the correct water level for your load or

allows time for clothes to soak.

Use only High Efciency (HE) detergent.

Concentrated Cleaning

Low-water cleaning means concentrated cleaning. Rather

than diluting detergent as done in an agitator-style washer,

this washer delivers the detergent directly to the soils.

Cleaning with Less Water

The most striking difference in your new washer is the

low-water washplate wash system. The washer automatically

adjusts the water level to the load size—no water level selector

is needed.

Traditional agitator-style

washer

Washer with low-water

washplate wash system

Washplate

Automatic Load Size Sensing

Once you start the cycle, the lid will lock, and the washer will

begin the sensing process to determine the correct water level

for the load. This may take several minutes before water is

added. You will nd a step-by-step description in the “Cycle

Status Lights” section.

You will hear the motor turn the basket in short pulses to

thoroughly wet the load. This low-water wash method

uses less water and energy compared to a traditional

agitator-style washer.

Control Panel and Features

SOIL LEVEL

Select the most suitable setting for your load. For heavily

soiled fabrics, select Heavy Soil Level for more wash time.

For lightly soiled fabrics, select Ex Light Soil Level for less

wash time. Lighter soil level setting will help reduce tangling

and wrinkling.

WASH TEMP

Wash Temp senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following the

garment label instructions, use the warmest wash water safe

for your fabric.

■ On some models and cycles, warm and hot water may

be cooler than your previous washer.

■ Even in a cold and cool water wash, some warm water

may be added to the washer to maintain a minimum

temperature.

WASH CYCLE KNOB

Use the Wash Cycle knob to select available cycles on

your washer. See “Cycle Guide” for detailed descriptions

of cycles.

RINSE OPTIONS

The following options may be added to most cycle.

See “Cycle Guide” for additional details.

1 RINSE

This option is used to limit a cycle to one rinse.

2 RINSES

This option can be used to automatically add a

second rinse to most cycles.

1 RINSE with SOFTENER

This option must be selected if using fabric softener

during a cycle. It ensures that the water levels are correct

for optimal fabric softener distribution.

2 RINSES with SOFTENER

This option turns on both the Fabric Softener and

the 2 Rinses option.

PRESOAK

Use this option to add an extra soak period to any cycle to

help loosen tough stains. The washer will ll and then pause

to soak, and then begin the selected cycle.

START/PAUSE BUTTON

Press to start the selected cycle; press again to pause

the cycle and unlock the lid.

NOTE: If the washer is spinning, it may take several

minutes to unlock the lid.

Press and hold 3 seconds to cancel a cycle and drain the

water from the washer.

CYCLE STATUS LIGHTS INDICATOR

The Cycle Status Lights show the progress of a cycle.

At each stage of the process, you may notice sounds or

pauses that are different from traditional washers.

SENSING

When the Start/Pause button is pressed, the washer will

rst perform a self-test on the lid lock mechanism. You

will hear a click, the basket will make a slight turn, and the

lid will unlock briey before locking again.

Once the lid has locked the second time, the washer

will use short, slow spins to estimate the load size.

These sensing spins may take 2 to 3 minutes before

water is added to the load and you may hear the hum

of these spins. If the sensing light is on, then washer is

working properly. You will hear the motor turn the basket

in short pulses to thoroughly wet the load. The washer

will then move the load briey, pause to allow water

to soak in to the load, and resume adding water. This

process may repeat until the correct amount of water

has been added for the load.

NOTE: Avoid opening lid during sensing. The sensing

process will start over when the washer is restarted.

The sensing light may also come on during the Soak

and Wash portions of the cycle. This is normal.

WASH

You will hear the motor and washplate moving the load.

Unlike traditional washers, the load is not covered with

water. Low-water cleaning means concentrated cleaning.

Rather than diluting detergent as done in an agitator-style

washer, this washer delivers the detergent directly to the

soils. The motor sounds may change at different stages

in the cycle. The wash time is determined by the selected

soil level.

2 3

4 5

RINSE

You will hear sounds similar to the wash cycle as the

washer rinses and moves the load.

SPIN

The washer spins the load at increasing speeds for proper

water removal, based on the selected cycle and spin

speed.

DONE

Once the cycle is complete, this light will come on.

Remove the load promptly for best results.

LOCKED

To allow for proper load sensing and

spinning, the lid will lock and the

Locked light will turn on. This light

indicates that the lid is locked and

cannot be opened.

If you need to open the lid, press

START/PAUSE. The lid will unlock once

the washer movement has stopped.

This may take several minutes if the

load was spinning at high speed.

NOTE: Holding the START/PAUSE Button

will cancel the cycle and cause the washer

to drain.

Press START/PAUSE again to resume the

cycle. Avoid opening the lid during sensing.

The sensing process will start over when

the washer is restarted.

Cycle Guide

For best fabric care, choose the cycle that best ts the load being washed.

Recommended settings for best performance are shown in Bold.

Not all cycles and options are available on each cycle. Not all settings and options are available on each cycle.

*All rinses are cold.

**Spin speed is integrated into the cycle and can not be selected.

Large items such

as sheets, sleeping

bags, small

comforters, jackets,

small washable rugs

Bulky Items/

Sheets

Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash large items such as jackets and small

comforters. The washer will ll with enough water to wet

down the load before the wash portion of the cycle begins,

and uses a higher water level than other cycles.

Sturdy fabrics,

colorfast items,

towels, jeans

Heavy Duty Hot

Warm

Cool

Cold

Tap Cold

High Provides maximum wash time and action for tough stains

and soils. Use this cycle for heavily soiled or sturdy items.

Water-level sensing process may take longer for some items

than for others because they will absorb more water than

other fabric types.

Casual and mixed

loads, jeans, towels,

sturdy fabrics

Deep Water

Wash

Hot

Warm

Cool

Cold

Tap Cold

High Provides additional water and alternating wash action for

heavily soiled mixed loads. Water-level sensing process may

take longer for some items than for others because they will

absorb more water than other fabric types.

Cottons, linens, and

mixed item loads

Normal Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle for normally soiled cottons and mixed fabric

loads.

Bright or darkly

colored cottons,

linens, casual and

mixed loads

Cold Wash Cold High Cold water with an additional wash action gently lifts

stains while caring for fabrics. Settings may be adjusted as

desired, but must use only cold water settings.

No-iron fabrics,

cottons, perm

press, synthetics

Casual Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent press,

and blends.

Machine-wash silks,

hand-wash fabrics

Delicate Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash lightly soiled items indicating

“Machine Washable Silks” or “Gentle” cycle on the care

label. Place small items in mesh garment bags before

washing. This cycle uses a higher, preset water level.

Small loads,

cottons, polyester,

perm press

Quick Wash Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle to wash small, lightly soiled loads of 2-3 items

that are needed in a hurry.

Heavily soiled

fabrics

Soak Hot

Warm

Cool

Cold

Tap Cold

No Spin Use this cycle to soak small spots of set in stains on fabrics.

The washer will use intermittent agitation and soaking. After

time has expired, water will drain, but the washer will not

spin. Cycle is complete.

Hand-washed items

or dripping wet

items

Drain &

Spin

N/A High This cycle uses a spin to shorten drying times for heavy

fabrics or special-care items washed by hand. Use this

cycle to drain washer after cancelling a cycle or completing

a cycle after a power failure.

Swimsuits and

items requiring

rinsing without

detergent

Rinse &

Spin

Cold rinse only High Combines a rinse and high speed spin for loads requiring

an additional rinse cycle or to complete a load after power

interruption. Also use for loads that require rinsing only.

No clothes in

washer

Clean Washer

with

affresh

Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water level.

Use with affresh

Washer Cleaner tablet or liquid chlorine

bleach to thoroughly clean the inside of your washer. This

cycle should not be interrupted. See “Washer Care.”

IMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh

cycle. Use

this cycle with an empty wash tub.

Items to wash: Cycle: Wash Temp*: Spin

Speed**:

Cycle Details:

Using Your Washer

• Empty pockets. Loose change, buttons, or any small

object can pass under the washplate and become trapped,

causing unexpected sounds.

• Sort items by recommended cycle, water temperature, and

colorfastness.

• Separate heavily soiled items from lightly soiled.

• Separate delicate items from sturdy fabrics.

• Do not dry items if stains remain after washing, because

heat can set stains into fabric.

• Treat stains promptly.

• Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

• Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

• When washing water-proof or water-resistant items, load

evenly. See “Cycle Guide” for tips and more information on

using the Bulky Items cycle.

• Use mesh item bags to help avoid tangling when washing

delicate or small items.

• Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

Always read and follow fabric care label instructions to avoid

damage to your items.

1. Sort and prepare your laundry

Add a measured amount of HE

detergent or single-dose laundry

packet into the basket.

If using Oxi-type boosters, color-safe

bleach, or fabric softener crystals, add

to the bottom of the washer basket

before adding clothes.

IMPORTANT: Use only High Efciency detergents. The

package will be marked “HE” or “High Efciency.” Low-water

washing creates excessive sudsing with a regular non-HE

detergent. Using regular detergent will likely result in longer

cycle times and reduced rinsing performance. It may also

result in component failures and noticeable mold or mildew.

HE detergents are made to produce the right amount of suds

for the best performance.

NOTE: Follow the manufacturer’s instructions to determine

the amount of laundry products to use.

2. Add laundry products

5. Add fabric softener, if desired

To dispense fabric softener in the rinse cycle,

this washer has been designed to allow the use of the Downy

Ball

®†

dispenser. Pour a measured amount of Downy

liquid

fabric softener into the Downy Ball

dispenser, pull the ring

tightly to seal it, and place on top of load. Always follow

manufacturer’s directions for correct amount of fabric softener

based on your load size. Then select 1 Rinse with Softener

option. The Downy Ball

dispenser will automatically release

the fabric softener during the rinse cycle. For questions on

using the Downy Ball

dispenser call 1-800-688-7638 or visit

www.downy.com.

IMPORTANT: Rinse option must be selected to 1 Rinse

with Softener or 2 Rinses with Softener to ensure proper

distribution at correct time in cycle. Do not overll or dilute.

Adding Liquid Fabric Softener Manually to Wash Load

During the nal rinse, wait until the washer has completed

lling, press the START/Pause button to pause the washer.

Lift the lid and add the measured recommended amount of

liquid fabric softener. Do not use more than the recommended

amount. Close the lid and press the START/Pause button again

to start the washer.

4. Add liquid chlorine bleach

to dispenser, if desired

Liquid

Chlorine Bleach

Do not overll, dilute, or use more than 1 cup (250 mL). Do

not use color-safe bleach or Oxi products in the same cycle

with liquid chlorine bleach.

Turn cycle knob to choose your wash cycle.

6. Select cycle

For best performance, load items

in loose heaps evenly around the

washplate. Try mixing different sized

items to reduce tangling.

IMPORTANT: Items need to move

freely for best cleaning and to reduce

wrinkling and tangling.

3. Load laundry into washer

†®Downy and Downy Ball are registered trademark of The Proctor & Gamble Company.

Wash Temp Suggested Fabrics

8. Select WASH TEMP

Once you select a cycle, select the wash temperature by

turning the Wash Temp knob to the desired setting.

Always read and follow fabric care label instructions to avoid

damage to your items.

9. Select cycle options, if desired

If you would like to add an extra rinse, fabric softener or

extra soak period to any cycle, turn the knob to desired

setting.

10. Press START/Pause

to begin wash cycle

Press the START/Pause button to start the wash cycle. When

the cycle has nished, the DONE indicator will light. Promptly

remove items after cycle has completed to avoid odor, reduce

wrinkling, and rusting of metal hooks, zippers, and snaps.

Unlocking the lid to add items

If you need to open the lid to add 1 or 2 missed items:

Press START/Pause; the lid will unlock once the washer

movement has stopped. This may take several minutes

if the load was spinning at high speed. Then close lid

and press START/Pause again to restart the cycle.

If lid is left open for more than 10 minutes the water will

pump out automatically.

Cool

Warm water is added to assist in

soil removal and to help dissolve

detergents.

Dark colors that

bleed or fade

Light soils

Hot

Some cold water is added to save

energy. This will be cooler than

your hot water heater setting.

Warm

Some cold water will be added, so

this will be cooler than what your

previous washer provided.

Cold

Warm water may be added to

assist in soil removal and to help

dissolve detergents.

Whites and pastels

Durable items

Heavy soils

Bright colors

Moderate to light soils

Colors that bleed

or fade

Light soils

Dark colors that

bleed or fade

Light soils

Tap Cold

This is the temperature from your

faucet.

7. Select SOIL LEVEL

Once you select a cycle, select the soil level by turning the

Soil Level knob to the desired setting.

Washer Maintenance

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of

replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See

the Installation Instructions for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always use High Efciency (HE) detergents and follow the

HE detergent manufacturer’s instructions regarding the

amount of HE detergent to use. Never use more than the

recommended amount because that may increase the

rate at which detergent and soil residue accumulate inside

your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help

dry out the washer and prevent the buildup of odor-

causing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This

Washer Maintenance Procedure should be performed,

at a minimum, once per month or every 30 wash cycles,

whichever occurs sooner, to control the rate at which soils

and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above, and use this recommended monthly

cleaning procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water

volumes in combination with affresh

Washer Cleaner

or liquid chlorine bleach to clean the inside of the washer.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh

Washer Cleaner tablet

in the detergent dispenser.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid.

f. Select the CLEAN WASHER cycle.

g. Press the START/Pause/Unlock button to begin the

cycle. The Clean Washer Cycle Operation is described

below.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press POWER/CANCEL. (For models

with no Power/Cancel button, press and hold START/

Pause/Unlock for three seconds). After the Clean Washer

cycle has stopped, run a RINSE & SPIN cycle to rinse

cleaner from washer.

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing

or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Select the CLEAN WASHER cycle.

f. Press the START/Pause/Unlock button to begin the

cycle. The Clean Washer Cycle Operation is described

below.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press POWER/CANCEL. (For models

with no Power/Cancel button, press and hold START/

Pause/Unlock for three seconds). After the Clean Washer

cycle has stopped, run a RINSE & SPIN cycle to rinse

cleaner from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will ll to a water level higher than in normal

wash cycles to provide rinsing at a level above the water

line for normal wash cycle.

2. During this cycle, there will be some agitation and

spinning to increase the removal of soils.

After this cycle is complete, leave the lid open to allow

for better ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may nd some

residue buildup in the washer’s dispensers. To remove

residue from the dispensers, wipe them with a damp cloth

and towel dry. Do not attempt to remove the dispensers or

trim for cleaning. The dispensers and trim are not removable.

If your model has a dispenser drawer, however, remove the

drawer and clean it before or after you run the Clean Washer

cycle. Use an all-purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills.

Use only mild soaps or cleaners when cleaning external

washer surfaces.

IMPORTANT: To avoid damaging the washer’s nish, do not

use abrasive products.

Operate your washer only when you are home. If moving,

or not using your washer for a period of time, follow these

steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid ooding due

to water pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on RINSE & SPIN cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

NON-USE AND VACATION CARE

2. Plug in washer or reconnect power.

3. Run washer through BULKY ITEMS/SHEETS cycle to

clean washer and remove antifreeze, if used. Use only

HE High Efciency detergent. Use 1/2 the manufacturer’s

recommended amount for a medium-size load.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

WINTER STORAGE CARE directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials

back inside washer. If you do not have packing tray,

place heavy blankets or towels into basket opening.

Close lid and place tape over lid and down front of

washer. Keep lid taped until washer is placed in new

location. Transport washer in upright position.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

Troubleshooting

If you experience Possible Causes Solution

Vibration or Off-Balance

Check the following for

proper installation or see

“Using Your Washer”

section.

Feet may not be in contact with the

oor and locked.

Front and rear feet must be in rm contact with oor, and washer

must be level to operate properly.

Washer may not be level. Check oor for exing or sagging. If ooring is uneven, a 3/4" (19

mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in Installation Instructions.

Load could be unbalanced. Load items in loose heaps evenly around the washplate. Add-

ing wet items to washer or adding more water to basket could

unbalance washer.

Do not tightly pack. Avoid washing single items.

Use Bulky Items/Sheets cycle for oversized, non-absorbent

items such as jackets and small comforters. See “Cycle Guide”.

See “Cycle Guide” and “Using Your Washer” in this Use and

Care Guide.

Noises

Clicking or metallic

noises

Objects could get caught in washer

drain system.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump. It may

be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming

sound with periodic gurgling or surging as nal amounts of water

are removed during the spin/drain cycles.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have

started the washer. This is normal.

Whirring Basket deceleration may be

occurring.

You may hear the whirring sound of the basket decelerating.

This is normal.

Water Leaks

Check the following for

proper installation:

Washer not level. Water may splash off basket if washer is not level. Check that

load is not unbalanced or tightly packed.

Fill hoses not attached tightly. Tighten ll-hose connection.

Fill hose washers. Make sure all four ll hose at washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for leaks

or clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water

pipes, and faucets.)

Washer not loaded as

recommended.

Unbalanced loading can cause basket to be out of alignment

and cause water to splash off tub. See “Using Your Washer”

for loading instructions.

Washer not performing as expected

Not enough water

in washer

Load not completely covered

in water.

This is normal operation for an HE low-water washer. The load

will not be completely under water. The washer senses load

sizes and adds correct amount of water for optimal cleaning.

See “What’s New under the Lid.”

IMPORTANT: Do not add more water to washer. Adding water

lifts the items off the washplate, resulting in less effective

cleaning.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer won’t run or ll,

washer stops working

or wash light remains

on (indicating that the

washer was unable to ll

appropriately)

Check for proper water supply. Both hoses must be attached and have water owing to inlet

valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ow.

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be stopped to reduce suds.

Washer may be tightly packed. Remove several items, rearrange load evenly around the

washplate. Close lid and press START/Pause.

Add only 1 or 2 additional items after washer has started.

Do not add more water to the washer.

Not using HE detergent or using too

much HE detergent.

Only use HE detergent. Suds from regular detergents can slow or

stop the washer. Always measure detergent and follow

detergent directions based on your load requirements.

To remove suds, cancel cycle. Select RINSE & SPIN. Press

START/Pause. Do not add more detergent.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected

Washer not draining/

spinning, loads are still

wet, or spin light remains

on (indicating that the

washer was

unable to pump out

water within 10 minutes)

Empty pockets and use garment

bags for small items.

Small items may have been caught in pump or between basket

and tub, which can slow draining.

Using a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/spin speed

for your item. To remove extra water in the load, select

DRAIN & SPIN. Load may need to be rearranged to allow even

distribution of the load in the basket.

The washer may be tightly packed or

unbalanced.

Tightly packed or unbalanced loads may not allow the washer to

spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain &

Spin cycle to remove excess water. See “Using Your Washer” for

loading recommendations.

Check plumbing for correct

drain hose installation. Drain hose

extends into standpipe farther than

4.5” (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96” (2.4 m)

above the oor. Remove any clogs from drain hose.

Too much detergent causing suds to

slow or stop draining and spinning.

Use only HE detergent. Always measure and follow detergent

directions for your load. To remove extra suds, select RINSE &

SPIN. Do not add detergent.

Dry spots on load

after cycle

High speed spins extract more

moisture than traditional top-load

washers.

The high spin speeds combined with air ow during the nal spin

can cause items near the top of the load to develop dry spots

during the nal spin. This is normal.

Incorrect or wrong wash

or rinse

temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet,

and have both hot and cold water owing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water owing to

the inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from

operating correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions based

on load size and soil level.

Washer may be tightly packed. The washer is less efcient at rinsing when tightly packed.

Load items in loose heaps evenly around the washplate.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional items after washer has started.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Sand, pet hair, lint, etc.

on load after washing

Heavy sand, pet hair, lint, and

detergent or bleach residues

may require additional rinsing.

Add 2 Rinses to the selected cycle.

Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed;

however, items will be wetter than those using a higher speed

spin. See the “Cycle Guide” to match your load with the best

cycle.

Load items in loose heaps evenly around the washplate.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of items being washed.

Not cleaning or

removing stains

Added more water to washer. Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move. It is normal

for the wash load to be not completely covered in water. Added

water lifts the laundry off the washplate, resulting in less effective

cleaning.

Washer not loaded as recommended. Washer is less efcient at cleaning when tightly packed.

Load items in loose heaps evenly around the washplate.

Add only 1 or 2 additional items after washer has started.

Adding detergent on top of load. Add detergent, oxi products and color-safe bleach to the bottom

of the basket before adding the items.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from

operating correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow manufacturer’s directions

based on load size and soil level.

Not using correct cycle for fabric

type.

Use a higher soil level cycle option and warmer wash

temperature to improve cleaning.

If using Quick Wash cycle, wash only a few items.

Use Heavy Duty cycle for tough cleaning. See the “Cycle Guide”

to match your load with the best cycle and fabric type.

Not using dispenser. Use dispenser to avoid chlorine bleach.

Load dispenser before starting a cycle.

Do not add products directly onto load.

Not using dispenser or Downy Ball

. Use dispenser for chlorine bleach and Downy Ball

dispenser for

fabric softener to avoid staining.

Load dispenser before starting a cycle.

Do not add products directly onto load.

Not selecting 1 Rinse with Softener

or 2 Rinses with Softener.

Always select 1 Rinse with Softener or 2 Rinses with Softener

when using fabric softener. Cycles that use spray rinsing will

add additional water for proper fabric softener dispensing when

selected.

Incorrect dispenser

operation

Clogged dispenser. Use only liquid chlorine bleach in the bleach dispenser.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Fabric Damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have

tangled.

Tie all strings and straps before starting wash load.

Items may have been damaged

before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if washer

is tightly packed.

Load items in loose heaps evenly around the washplate.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional items after washer has started.

Liquid chlorine bleach may have

been added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load Items on top of bleach dispenser when

loading and unloading washer.

Garment care instructions may not

have been followed.

Always read and follow item manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with the

best cycle.

Odors Monthly maintenance not done as

recommended.

Run the Clean Washer with affresh

cycle after every 30 washes.

See “Washer Care” section.

Unload washer as soon as cycle is complete.

Using wrong or too much detergent. Use only HE detergent. Be sure to measure correctly. Always

follow the manufacturer’s directions.

See “Washer Care” section.

Lid Locked light is

ashing

The lid is not closed. Close the lid. The washer will not start or ll with the lid open.

A cycle was stopped or paused using

the START/Pause button.

The washer may still be spinning. The lid will not unlock until the

basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before

adding clothes. Do not add packet to dispensers. Follow the

manufacturer’s instructions to avoid damage to your items.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

WHIRLPOOL

LAUNDRY

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

03/14

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair.

Some questions can be addressed without service. Please take a few minutes to review the

Troubleshooting or Problem Solver section of the Use and Care Guide, scan the QR code on

the right to access additional resources, or visit https://www.whirlpool.com/product_help.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers.

In the U.S. and Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A. call 1-800-253-1301. In Canada call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

https://www.whirlpool.com/product_help

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

1. Commercial, non-residential, multiple-family use, or use inconsistent with published

user, operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes, or correction of household electrical or

plumbing (i.e. house wiring, fuses, or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters, etc.).

5. Conversion of your product from natural gas or L.P. gas or reversal of appliance doors.

6. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use with products

not approved by Whirlpool.

7. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration, or modiﬁcation of the appliance.

8. Cosmetic damage including scratches, dents, chips, and other damage to appliance

ﬁnishes unless such damage results from defects in materials and workmanship and is

reported to Whirlpool within 30 days.

9. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive

environments, including but not limited to, high salt concentrations, high moisture or

humidity, or exposure to chemicals.

10. Pick-up or delivery. This product is intended for in-home repair.

11. Travel or transportation expenses for service in remote locations where an authorized

Whirlpool servicer is not available.

12. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e. trim,

decorative panels, ﬂooring, cabinetry, islands, countertops, drywall, etc.) that interfere

with servicing, removal, or replacement of the product.

13. Service or parts for appliances with original model/serial numbers removed, altered, or

not easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

For one year from the date of purchase,

when this major appliance is installed,

operated, and maintained according to

instructions attached to or furnished with

the product, Whirlpool Corporation or

Whirlpool Canada LP (hereafter “Whirlpool”)

will pay for Factory Specified Replacement

Parts and repair labor to correct defects

in materials or workmanship that existed

when this major appliance was purchased,

or at its sole discretion replace the product.

In the event of product replacement, your

appliance will be warranted by the remaining

term of the original unit’s warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY

UNDER THIS LIMITED WARRANTY SHALL

BE PRODUCT REPAIR AS PROVIDED

HEREIN. Service must be provided by a

Whirlpool designated service company. This

limited warranty is valid only in the United

States or Canada and applies only when

the major appliance is used in the country

in which it was purchased. This limited

warranty is effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain service

under this limited warranty.

Sécurité de la laveuse

Quoi de neuf sous le couvercle?

Choix du détergent approprié

Utiliser uniquement des détergents Haute efcacité.

L’emballage portera la mention “HE” ou “High Efciency”

(haute efcacité). Un lavage avec faible consommation d’eau

produit un excès de mousse avec un détergent non HE

ordinaire. Il est probable que l’utilisation d’un détergent ordinaire

prolongera la durée des programmes et réduira la performance

de rinçage. Ceci peut aussi entraîner des défaillances des

composants et une moisissure perceptible. Les détergents

HE sont conçus pour produire la quantité de mousse adéquate

pour le meilleur rendement. Suivre les recommandations du

fabricant pour déterminer la quantité de détergent à utiliser.

Sons normaux prévisibles

Au cours des différents stades du programme de lavage, vous

entendrez peut-être des bruits que votre laveuse précédente

ne produisait pas. Par exemple, vous entendrez peut-être

un cliquetis au début du programme lorsque le système

de verrouillage du couvercle effectue un test automatique.

Différents bourdonnements et bruits de frottements rythmiques

se produiront à mesure que le plateau de lavage déplace

la charge et que le panier ralentit jusqu’à l’arrêt. Parfois, il

est possible que la laveuse soit complètement silencieuse,

lorsqu’elle détermine le niveau d’eau adéquat ou qu’elle laisse

tremper les vêtements.

Utiliser uniquement un détergent Haute efcacité (HE).

Nettoyage concentré

Le système de lavage à faible consommation d’eau signie un

lavage concentré. Plutôt que de diluer du détergent comme

dans une laveuse de type agitateur, cette laveuse libère le

détergent directement sur les endroits souillés.

Nettoyer avec moins d’eau

La nouveauté la plus agrante de cette nouvelle laveuse est

son système de lavage à faible consommation d’eau avec

plateau de lavage. La laveuse ajuste automatiquement le

niveau d’eau en fonction de la taille de la charge — nul besoin

de sélecteur de niveau d’eau.

Laveuse traditionnelle de

type agitateur

Laveuse à faible consommation

d’eau avec plateau de lavage

Plateau de lavage

Détection automatique

de taille de charge

Une fois que l’on démarre le programme, le couvercle se

verrouille et la laveuse entame un processus de détection pour

déterminer le niveau d’eau approprié à la charge. Cela peut

prendre plusieurs minutes avant que l’eau ne soit ajoutée. Voir

la description pas-à-pas dans la section “Témoins lumineux des

programmes”.

Vous entendrez le moteur faire tourner le panier par de brefs

mouvements d’impulsion pour bien imbiber la charge. Cette

méthode de lavage avec faible consommation d’eau utilise

moins d’eau et d’énergie qu’une laveuse traditionnelle de type

agitateur.

Pour un meilleur rendement, il est recommandé de déposer

les vêtements en vrac et de façon uniforme le long du plateau

de lavage.

À mesure que la laveuse imbibe et déplace la charge, les

vêtements se tassent dans le panier. Ceci est normal et ne

signie pas que l’on doive rajouter des vêtements.

IMPORTANT : Le panier de la laveuse ne sera pas rempli d’eau,

comme avec votre précédente laveuse de type agitateur. Il est

normal qu’une partie de la charge dépasse du niveau d’eau.

Tableau de commande et caractéristiques

2 3

4 5

SOIL LEVEL (niveau de saleté)

Dans la majorité des cas, sélectionner le réglage le

plus adapté à votre charge. Pour les tissus très sales,

sélectionner Heavy Soil Level (niveau de saleté important)

pour prolonger la durée de lavage. Pour les tissus peu sales,

sélectionner Ex Light Soil Level (niveau de saleté très faible)

pour abréger la durée de lavage. Le réglage de niveau de

saleté faible aidera à réduire l’emmêlement et le froissement.

WASH TEMP (température de lavage)

La fonction WASH TEMP (température de lavage) détecte et

maintient une température uniforme de l’eau en régulant le

débit d’arrivée d’eau chaude et d’eau froide.

Sélectionner une température de lavage en fonction du type

de tissu et de saleté à laver. Pour des résultats optimaux,

suivre les instructions sur l’étiquette du vêtement et utiliser

la température d’eau de lavage la plus chaude possible qui

reste sans danger pour le tissu.

• Sur certains modèles et pour certains programmes, les

températures utilisées pour l’eau chaude et l’eau tiède

peuvent être inférieures aux températures utilisées par

votre précédente laveuse.

• Même avec un lavage à l’eau froide, il est possible que

de l’eau tiède soit ajoutée à la laveuse pour maintenir une

température minimale.

BOUTON DE PROGRAMME DE LAVAGE

Utiliser le bouton de programme de lavage pour sélectionner

les programmes disponibles sur la laveuse. Voir “Guide de

programmes” pour des descriptions détaillées.

RINSE OPTIONS (options de rinçage)

Il est possible d’ajouter les options suivantes à la plupart

des programmes. Voir “Guide de programmes” pour plus

de détails.

1 RINSE (rinçage unique)

Cette option permet de limiter le nombre de rinçages d’un

programme à un seul rinçage.

2 RINSES (double rinçage)

On peut utiliser cette option pour ajouter automatiquement

un second rinçage à la plupart des programmes.

1 RINSE with SOFTENER (rinçage unique avec

assouplissant)

Cette option doit être sélectionnée si l’on utilise de

l’assouplissant pour tissu durant un programme. Ceci

garantit que l’assouplissant pour tissu est ajouté au bon

moment lors du rinçage pour être correctement distribué.

2 RINSES with SOFTENER (double rinçage avec

assouplissant)

Cette option active les options Fabric Softener

(assouplissant pour tissu) et 2 Rinses (double rinçage).

PRESOAK (Pré-trempage)

Utiliser cette option pour ajouter une période de trempage

supplémentaire à n’importe quel programme pour le

nettoyage de vêtements très sales. Il est possible d’ajuster

la durée du trempage en modiant le Soil Level (Niveau de

saleté).

BOUTON START/PAUSE (mise en marche/pause)

Appuyer sur ce bouton pour démarrer le programme

sélectionné, puis appuyer de nouveau pour suspendre

le programme et déverrouiller le couvercle.

REMARQUE : Si la laveuse tourne, le couvercle peut mettre

quelques minutes à se déverrouiller. Appuyer pendant

3 secondes pour annuler un programme et vidanger l’eau de

la laveuse.

TÉMOINS LUMINEUX DES PROGRAMMES

Les témoins lumineux indiquent la progression du

programme. À chaque étape du processus, il est possible

que l’on remarque des pauses ou des sons différents de

ceux des laveuses ordinaires.

SENSING (détection)

Lorsqu’on appuie sur le bouton START/Pause (Mise en

marche/pause), la laveuse effectue un test automatique

sur le mécanisme de verrouillage du couvercle. On entend

un déclic, le panier effectue un léger tour, et le couvercle

se déverrouille brièvement avant de se verrouiller à

nouveau.

Une fois le couvercle verrouillé pour la deuxième fois, la

laveuse utilise des essorages lents et courts pour estimer

le volume de la charge. Ces essorages de détection

peuvent prendre 2 à 3 minutes avant que de l’eau ne soit

ajoutée à la charge et les essorages peuvent émettre

un bourdonnement. Si le témoin lumineux de détection

est allumé, cela signie que la laveuse fonctionne

correctement. On entend le moteur qui fait tourner le

panier par de courtes impulsions pour mouiller l’intégralité

de la charge. La laveuse déplace ensuite brièvement la

charge, fait une pause pour permettre à l’eau de tremper

la charge, et continue à ajouter de l’eau. Ce processus

peut se répéter jusqu’à ce que la quantité d’eau correcte

ait été ajoutée à la charge.

La page charge ...

Whirlpool WTW5000DW Mode d'emploi

Marque: Whirlpool

Modèle: WTW5000DW

Catégorie: Machines à laver

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WTW5000DW User guide

Whirlpool WTW5000DW Mode d'emploi

Whirlpool WTW5000DW Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents