Twin Eagles Power Burner Gas Conversion Instruction
- Taper
- Gas Conversion Instruction
In Massachuses: All gas products must be installed using a “Massachuses”
licensed plumber or gas er. A “T” handle type manual gas valve must be
installed in the gas supply line to this appliance. This applies to permanently
installed natural gas and propane installaons. This does not apply to
propane portable installaons using a 20 pound tank.
!
WARNING
BEFORE WORKING ON THIS APPLIANCE, DISCONNECT
GAS AND ELECTRICAL SUPPLIES.
!
WARNING
INSTALLATION/GAS CONVERSION MUST BE PER-
FORMED BE A QUALIFIED TECHNICIAN.
TWIN EAGLES POWER BURNER
GAS CONVERSION KIT FROM LP TO NG
PN: CKNG-TEPB
FOR MODELS: TEPB
FOR YOUR RECORDS
IMPORTANT: Retain original proof of purchase to establish warranty
period.
Please record the following informaon and refer to this informaon
when contacng the company or an authorized service agent. This
informaon is found on the rang/data plate located on the inside wall
of the rebox.
Serial No. of Power Burner:
___________________________________________________________
Date of NG Gas Conversion:
___________________________________________________________
NG Gas Conversion by:
___________________________________________________________
WARNING: CALIFORNIA PROPOSITION 65
This product can expose you to chemicals including carbon monoxide which is known to the
State of California to cause cancer and reproducve harm. To minimize exposure to the by-
products of the burning fuel or from combuson, always operate this unit according to the
use and care manual and provide good venlaon. California law requires businesses to warn
customers of potenal exposure to such substances. For more informaon go to
www.P65Warnings.ca.gov.
AVERTISSEMENT: PROPOSITION 65 DE L’ETAT DE LA CALIFORNIE
Cet appareil peut vous exposer aux produits chimiques et au gaz monoxyde de carbonne
reconnue dans l’Etat de la Californie pour causer le cancer et des problemes de ferlite. Pour
minimiser l’exposion de ces-sous produits combusbles ou de la combuson, uliser toujours
cet appareil en conformitee au manuel d’ulisaon et d’entreen en s’assurant egalement
d’une bonne venlaon. La loi de la Californie exige aux fabricants d’informer leurs clients aux
risques d’exposion potenelle a de telles substances. Pour plus d’informaon, visiter le site
www.P65Warnings.ca.gov
PN: 18656E 07/19
Before
(Set to LP)
Aer
(Set to NG)
ORIFICE BURNER
(OUTER RING)
ORIFICE BURNER
(INNER RING)
FIG. 1
FIG. 2
INNER RING AIR
SHUTTER
OUTER RING AIR
SHUTTER
1. Check to make sure that you have the LP Gas Conversion Kit as follows:
A. PN: 15110-30, Orice #30 (1 pc)
B. PN: 15110-41, Orice #41 (1 pc)
C. PN: S16110, Wire Tie (2 pcs)
D. PN: 18351, Label, Conversion, Gas (1 pc)
E. PN: 18656: Gas Conversion Instrucon (1 pc)
2. Gas Conversion
A. Remove the grates and set them aside.
B. Li then pull the brass burner towards the back.
• Note: Ensure that the wires for the igniter are not damage while
pulling o the burner. When removing the burner, you may need to
remove the front panel and cut the wire es that are retaining the
excess length of igniter wire. Use the wire es provided to retain the
wire aer the leak test is performed.
C. Replace the orice #53 used on NG (Inner Ring of the Burner), and
replace it with orice #41, used for LP (Inner Ring of the Burner). Use
a 1/2” Deep Socket and a Socket Wrench to remove and replace the
orice. (Fig. 1)
D. Replace the orice #49 used on NG (Outer Ring of the Burner), and
replace it with orice #30, used for LP (Outer Ring of the Burner). Use
a 1/2” Deep Socket and a Socket Wrench to remove and replace the
orice. (Fig. 1)
E. Set the air shuer opening to the following specicaon: (Fig. 2)
• Inner Ring Air Shuer: 1/2”
• Outer Ring Air Shuer: 5/8”
F. The regulator is located on the boom right side of the Power Burner.
Remove the cap on the regulator then remove the center plasc insert
and invert it to show the LP marking. Put the cover back. Connect LP
gas line to the regulator directly.
3. Tesng
A. Make sure the regulator has been properly connected, replaced for LP
Gas
B. Check for leaks.
C. NEVER USE THE UNIT WITHOUT FIRST LEAK TESTING THE GAS
CONNECTION.
a. Prepare a leak tesng soluon of sudsy water by mixing in a spray
bole with half liquid soap and half water.
b. Conrm that all control knobs are in the “OFF” posion.
c. Turn the main gas valve supply “ON”.
d. Apply leak tesng soluon by spraying on the pipe joints, ngs, and
hose.
e. A gas leak is detected if;
i. there is a faint gas smell and/or
ii. growing bubbles appear on any of the connecon points and/or
hose. DO NOT aempt to turn on the burners and IMMEDIATELY
turn o the gas supply valve.
f. When there is a gas leak, call a qualied service technician. DO NOT
use the unit unl the leak is corrected.
D. Fill up the Conversion Label. Next, paste it next to the original Serial
Plate.
E. The conversion is complete and the unit is ready for installaon. Refer
back to the Installaon Manual.
-
1
-
2
Twin Eagles Power Burner Gas Conversion Instruction
- Taper
- Gas Conversion Instruction
dans d''autres langues
- English: Twin Eagles Power Burner