Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Guide d'installation

Marque: Mammoth

Modèle: R6GP 6, 7.5 - 10 Ton Archived 2/23/12

Taper: Guide d'installation

R6GP - 072/090/120 Series

Installation Instructions

Single Package Gas Heating/Electric Cooling Rooftop Units

R6GP-090 Shown

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being able to install the product according to strict safety

guidelines and instructing the customer on how to operate and maintain the equipment for the life of the product. Safety should always be the

deciding factor when installing this product and using common sense plays an important role as well. Pay attention to all safety warnings and

any other special notes highlighted in the manual. Improper installation of the unit or failure to follow safety warnings could result in serious

injury, death, or property damage. These instructions are primarily intended to assist qualiﬁ ed individuals experienced in the proper installation

of this appliance. Some local codes require licensed installation/service personnel for this type of equipment. After completing the installation,

return these instructions to the customer’s package for future reference.

WARNING:

DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly

could result in serious injury or property

damage.

• Installation and service must be performed

by a qualiﬁ ed installer, service agency or the

gas supplier.

• Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a

neighbors phone. Follow the gas suppliers

instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

High Efﬁ ciency

SAFETY INFORMATION .............................................3

REQUIREMENTS AND CODES ..................................4

GENERAL INFORMATION ..........................................4

Air Ducts ..................................................................4

Air Filter Requirements ............................................4

Clearances to Combustible Materials ......................5

Combustion Air Quality ............................................5

Condensate Drain ....................................................5

Equipment Check ....................................................5

Equipment Application .............................................5

Heating Load ...........................................................5

Thermostat ..............................................................5

VENTING REQUIREMENTS ........................................6

COMBUSTION AIR REQUIREMENTS ........................6

UNIT INSTALLATION ..................................................7

Packaging Removal .................................................7

Rigging and Hoisting ...............................................7

Minimum Clearance Requirements .........................8

Rooftop Mounting ....................................................8

Ground Level ...........................................................8

CIRCULATING AIR SUPPLY .......................................9

Unconditioned Spaces .............................................9

Acoustical Ductwork ................................................9

Downﬂ ow to Horizontal Conversion .........................9

GAS SUPPLY AND PIPING .......................................10

Leak Check ............................................................10

High Altitude Deration ............................................10

Conversion to LP/Propane .....................................11

ELECTRICAL WIRING ...............................................11

Pre-Electrical Checklist ..........................................11

Line Voltage ...........................................................12

Grounding ..............................................................12

Unbalanced 3-Phase Supply Voltage ....................12

Blower Speed ........................................................13

Thermostat ............................................................13

Heat Anticipator .....................................................13

STARTUP AND ADJUSTMENTS ..............................13

Pre-Start Check List ..............................................13

Startup Procedures ................................................14

Air Circulation ........................................................14

System Cooling .....................................................14

System Heating .....................................................14

Verifying and Adjusting Temperature Rise .............14

Verifying Burner Operation ....................................15

Verifying Operation of Over-Temperature

Limit Control ..........................................................15

Verifying and Adjusting Firing Rate .......................15

OPERATING SEQUENCE .........................................16

Cooling Mode ........................................................16

Heating Mode (200 & 235 kBtuh) ......................... 16

Heating Mode (100 & 166 kBtuh) ......................... 16

Blower Mode ......................................................... 16

TROUBLESHOOTING .............................................. 17

UNIT MAINTENANCE ................................................17

Condensate Drain and Outdoor Coil ......................17

Air Filters ...............................................................17

Blower Compartment .............................................18

Heat Exchanger and Burner Maintenance ............18

Cleaning of Burners ...............................................18

Cleaning of Heat Exchanger ..................................18

Vent Cover Assembly .............................................19

Electrical ................................................................19

Motor Lubrication ...................................................19

Refrigerant Charging .............................................19

COMPONENT FUNCTIONS ......................................20

Centrifugal Switch ..................................................20

Flame Roll-Out Control ..........................................20

Flame Sensor ........................................................20

Gas Valve ...............................................................20

High Pressure Switch ............................................20

Indoor Coil Freeze Protection Thermostats ...........20

Low Pressure Switch .............................................20

Over-Temperature Limit Control ............................20

Pressure Switch .....................................................20

FIGURES and TABLES .............................................21

Figure 12 - Component Locations .......................21

Physical Dimensions ..............................................22

Figure 12 - 072 Series .........................................22

Figure 13 - 090 Series .........................................24

Figure 14 - 120 Series .........................................26

Table 4 - Unit Shipping Weights ..........................27

Blower Performance Data ......................................28

Table 5 - 072C - 100 Series - Downﬂ ow ..............28

Table 6 - 072C - 100 Series - Horizontal .............29

Table 7 - 072C -166 Series - Downﬂ ow ...............30

Table 8 - 072C - 166 Series - Horizontal .............31

Table 9 - 090C Series - Downﬂ ow .......................32

Table 10 - 090C Series - Horizontal ....................33

Table 11 - 120C Series - Downﬂ ow .....................34

Table 12 - 120C Series - Horizontal ....................35

Electrical Information .............................................36

Table 13 - Electrical Data ....................................36

Figure 15 - Ladder Diag. - 072 Series .................37

Figure 16 - Ladder Diag. - 090/120 Series ..........38

Figure 17 - Wiring Diagram - 072 Series .............39

Figure 18 - Wiring Diagram - 090 Series .............40

Figure 19 - Wiring Diagram - 120 Series .............41

Gas Information .....................................................42

Table 14 - Gas Pipe Capacities ...........................42

Table 15 - Oriﬁ ce or Drill Sizes ............................42

Table 16- Heating Rise/Range ............................42

Table 17- Gas Flow Rates ...................................43

R6 Charging Charts ...............................................44

Figure 20 - R6GP-072 Series ..............................44

Figure 21 - R6GP-090 Series ..............................45

Figure 22 - R6GP-120 Series ..............................45

R6 Gas Valve Labels .............................................46

Figure 23 - 6 Ton Units ........................................46

Figure 24 - 7.5 and 10 Ton Units .........................47

INSTALLATION CHECKLIST ....................................48

TABLE OF CONTENTS

SAFETY INFORMATION

Safety markings are used frequently throughout this

manual to designate a degree or level of seriousness and

should not be ignored. WARNING indicates a potentially

hazardous situation that if not avoided, could result in

personal injury or death. CAUTION indicates a potentially

hazardous situation that if not avoided, may result in minor

or moderate injury or property damage.

WARNING:

PROPOSITION 65 WARNING: This product

contains ﬁ berglass wool, a product known to the

state of California to cause cancer. Disturbing

the insulation of this product during installation,

maintenance, or repair will expose you to

ﬁ berglass wool.

• Breathing this material may cause respiratory

irritations or may cause lung cancer.

• Fiberglass wool may also cause eye

irritation, skin sensitization, or other allergic

responses in susceptible individuals.

• Always wear goggles, disposable gloves,

long sleeved shirt, and appropriate breathing

protection when working near this insulation.

If contact with skin occurs, wash immediately

with soap and water. In case of contact with

eyes, ﬂ ush immediately with water for at

least 15 minutes. Contact a physician if

needed.

WARNING:

Improper installation, service, adjustment, or

maintenance may cause explosion, ﬁ re, electrical

shock or other hazardous conditions which may

result in personal injury or property damage.

Unless otherwise noted in these instructions,

only factory authorized kits or accessories may

be used with this product.

WARNING:

Do not place combustible material on or against

the unit cabinet. Do not place combustible

materials, including gasoline and any other

ﬂ ammable vapors and liquids, in the vicinity of

the unit.

WARNING:

The safety information listed below must be

followed during the installation, service, and

operation of this unit. Failure to follow safety

recommendations could result in possible

damage to the equipment, serious per

sonal

injury or death

• This equipment contains liquid and gaseous refrigerant

under high pressure. Installation or servicing should only

be performed by qualiﬁ ed trained personnel thoroughly

familiar with this type equipment.

• All electrical wiring must be completed in accordance

with local, state and national codes and regulations

and with the National Electric Code (ANSI/NFPA 70)

or in Canada the Canadian Electric Code Part 1 CSA

C.22.1.

• Use only with the type of gas approved for this unit.

Refer to the unit rating plate.

• Install this unit only in a location and position as speciﬁ ed

on page 8.

• Provide adequate combustion and ventilation air to the

unit as speciﬁ ed on page 6.

• Provide adequate clearances around the air vent intake

terminal as speciﬁ ed in on page 6.

• Combustion products must be discharged outdoors.

Connect this unit to an approved vent system only, as

speciﬁ ed on page 6.

• Never test for gas leaks with an open ﬂ ame. Use a

commercially available soap solution to check all

connections (See page 10).

• Consult Table 16 (page 42), and the rating plate for the

proper circulating air ﬂ ow and temperature rise. It is

important that the duct system be designed to provide

the correct ﬂ ow rates and external pressure rise. An

improperly designed duct system can result in nuisance

shutdowns, and comfort or noise issues.

• Follow all precautions in the literature, on tags and

on labels provided with the unit and/or approved ﬁ eld

installed kits. The type of hazard and severity are

described on each label or tag.

• This unit is designed only for outdoor installations and

should be located with consideration of minimizing the

length of the supply and return ducts. Consideration

should also be given to the accessibility of fuel, electric

power, service access, noise, and shade.

GENERAL INFORMATION

WARNING:

Improper installation, service, adjustment, or

maintenance may cause explosion, ﬁ re, electrical

shock or other hazardous conditions which may

result in personal injury or property damage.

Unless otherwise noted in these instructions,

only factory authorized kits or accessories may

be used with this product.

R6GP Series Single Package Gas Heating/Electric

Cooling units are designed for outdoor rooftop or ground

level slab installations. The units are shipped ready for

downﬂ ow duct connections and are easily converted for

horizontal duct connections with an optional accessory

kit. See the unit Technical Sales Literature for factory

and field installed accessory information and part

numbers. This information can also be found online at

www.nordyne.com.

Air Ducts

• Air Ducts must be installed in accordance with the

National Fire Protection Association “Standards for

Installation of Air Conditioning and Ventilation Systems”

(NFPA 90A). The ductwork should be appropriately

sized to the capacity of the heating unit to ensure its

proper airﬂ ow rating.

• Installation of combination heating/cooling units

must also conform with current C.S.A. Standard B52

“Mechanical Refrigeration Code.”

Air Filter Requirements

WARNING:

Never operate the unit without a ﬁ lter in place.

Dust and lint could accumulate on internal parts,

resulting in loss of efﬁ ciency, equipment damage

and possible ﬁ re.

All return air must pass through the ﬁ lters before entering

the unit. It is important that all ﬁ lters be kept clean and

replaced frequently to ensure proper operation of unit.

Dirty or clogged ﬁ lters will reduce the efﬁ ciency of the

unit and result in unit shutdowns. Air ﬁ lter pressure drop

must not exceed 0.08 inches WC.

When replacing the air

ﬁ lters, a suitable air ﬁ lter must be installed ahead of the

evaporator coil of the return air system. Refer to page 17

for recommended ﬁ lter sizes.

REQUIREMENTS and CODES

This unit must be installed in accordance with

these instructions, all applicable local building

codes and the current revision of the National

Fuel Gas Code (NFPA54/ANSI Z223.1) or the

Natural Gas and Propane Installation Code,

CAN/CGA B149.1.

Additional codes listed below are for reference purposes

only and do not necessarily have jurisdiction over local or

state codes. Local codes and regulations take precedence

over any recommendations contained in these instructions.

Always consult with local authorities before installing any

gas appliance.

Combustion and Ventilation Air

• US: National Fuel Gas Code (NFGC), Air for Combustion

and Ventilation

• CANADA: Natural Gas and Propane Installation Codes

(NSCNGPIC), Venting Systems and Air Supply for

Appliances

Duct Systems

• US and CANADA: Air Conditioning Contractors

Association (ACCA) Manual Q, Sheet Metal and

Air Conditioning Contractors National Association

(SMACNA), or American Society of Heating,

Refrigeration, and Air Conditioning Engineers

(ASHRAE) Fundamentals Handbook

Electrical Connections

• US: National Electrical Code (NEC) ANSI/NFPA 70

• CANADA: Canadian Electrical Code CSA C22.1

Gas Piping and Gas Pipe Pressure Testing

• US: NFGC and National Plumbing Codes

• CANADA: NSCNGPIC

General Installation

• US: Current edition of the NFGC and the NFPA 90B. For

copies, contact the National Fire Protection Association

Inc., Batterymarch Park, Quincy, MA 02269; or American

Gas Association, 400 N. Capitol, N.W., Washington DC

20001 or www.NFPA.org.

• CANADA: NSCNGPIC. For a copy, contact Standard

Sales, CSA International, 178 Rexdale Boulevard,

Etobicoke (Toronto), Ontario, M9W 1R3 Canada

Safety

• US: (NFGC) NFPA 54–1999/ANSI Z223.1 and the

Installation Standards, Warm Air Heating and Air

Conditioning Systems ANSI/NFPA 90B.

• CANADA: CAN/CGA-B149.1–and .2–M00 National

Standard of Canada. (NSCNGPIC)

The condensate drain line must be J-trapped using ﬁ eld

supplied parts and may be combined with other drain

lines when routed to the drain.

When connecting rigid drain line, hold any ﬁ ttings with a

wrench to prevent twisting. Do not overtighten!

Clearances to Combustible Materials

• The R6GP series gas/electric unit is suitable for

installation on combustible ﬂ ooring or class A, B, or C

rooﬁ ng materials.

• A clearance of at least 36 inches from the blower

access panel and from the louvered control access

panel is the required clearance to combustibles. Please

refer to Figure 6 (page 8) for all requirements. Where

accessibility to combustibles clearances are greater

than minimum clearances, accessibility clearances

must take preference.

• Sufﬁ cient clearance for unobstructed airﬂ ow through

the louvered control access panel and through the

outdoor coil must be maintained in order to achieve

rated performance.

Combustion Air Quality

WARNING:

Combustion air must not be drawn from a

contaminated atmosphere. Excessive exposure

to contaminated combustion air will result in

safety and performance related problems.

To maximize heat exchanger life, the combustion air

must be free of chemicals that can form corrosive acidic

compounds in the combustion gases. The recommended

source of combustion air is to use clean air from outside.

DO NOT place any chemicals with ﬂ ammable or caustic

vapors or these other corrosive chemicals near the

vent termination:

• Gasoline/Kerosene

• Permanent wave solutions

• Chlorinated waxes and cleaners

• Chlorine based swimming pool chemicals

• Water softening chemicals

• De-icing salts or chemicals

• Carbon tetrachloride

• Halogen type refrigerants

• Cleaning solvents

• Cements, glues, paint removers, varnishes, etc.

• Hydrochloric acid

• Masonry acid washing materials

• Plumbing Stack

Condensate Drain

The method for disposing of condensate varies accord-

ing to local codes. Consult your local code or authority

having jurisdiction.

Condensate is drained from the unit through a

3/4” (19mm) PVC pipe located on the front side of the

unit (Figure 1). For proper drainage, install a 3” (8cm)

Min. trap between the drain line and an open vent of the

same size. Avoid areas where condensate drainage may

cause problems.

3”

Min

Roof Curb

Condensate

Drain

Figure 1. Condensate Drain

Equipment Check

All units have been securely packaged at the point of

shipment. After unpacking the unit, carefully inspect for

apparent and concealed damage. Claims for damage

should be ﬁ led with the carrier by the consignee.

Equipment Application

Before beginning the installation, verify the unit voltage

requirements and that the model is correct for the job. The

unit model number is printed on the data label. This unit

is NOT to be used for temporary heating of buildings or

structures under construction.

Heating Load

This unit should be sized to provide the design heating

load requirement. Heating load estimates can be made

using approved methods available from Air Conditioning

Contractors of America (Manual J); American Society of

Heating, Refrigerating, and Air Conditioning Engineers;

or other approved engineering methods. For installations

above 2,000 ft., the unit should have a sea level input

rating large enough that it will meet the heating load after

deration for altitude.

Thermostat

A two-stage cooling/ heating 24VAC thermostat should

be used with these units, and installed according to the

instructions supplied by the thermostat manufacturer. The

thermostat should not be installed on an outside wall or

any other location where its operation may be adversely

affected by radiant heat sources such as sunlight, lighting

ﬁ xtures, or ﬁ replaces and convective heat from warm/cold

air registers or electrical appliances.

VENTING REQUIREMENTS

WARNING:

This unit is intended for outdoor installation

only. Do not vent the unit through a conventional

venting system.

This unit has been equipped with an integral venting

system and designed to operate only with this venting

system. No additional venting shall be used. This unit

must be vented to the outdoors.

WARNING:

The vent cover assembly must be installed to

assure proper operation of the unit.

A vent cover assembly has been supplied with the unit

and can be found secured to the gas controls within the

burner area of this unit.

Figure 2 displays the proper installation of the vent cover

assembly over the vent outlet of the corner panel. The

fasteners used to secure the vent cover assembly have

been included on the unit end panel.

• Ensure that the exhaust gases will not impinge

on windows or building surfaces, which may be

compromised or damaged by condensation.

• Do not install the unit in a location where exhaust from

the vent termination will be directed into windows,

stairwells, under decks, or other recessed areas.

Figure 2. Vent Cover Assembly

The list below summarizes the location requirements for

the venting system termination:

• The location of the vent termination must be consistent

with the National Fuel Gas Code (ANSI Z223.1) or

CAN/CGA-B149 Installation Codes.

• Must be located at least four (4) feet horizontally from

any electric meters, gas meters, regulators, and relief

equipment.

• Must be located at least 3 feet above any forced air

inlet located within 10 feet of unit.

• Must be located at least 4 feet below, 4 feet horizontally

from, or 1 foot above any door, window, or gravity air

inlet into any building.

• Must be located at least 1 foot above grade and installed

in such a manner as to prevent snow accumulation

from obstructing the vent termination.

• The vent termination must not be located above any

public walkways.

COMBUSTION AIR REQUIREMENTS

WARNING:

Installation using methods other than those

described in the following sections must comply

with the National Fuel Gas Code and all applicable

local codes.

Provisions must be made during the installation of this unit

that provide an adequate supply of air for combustion.

• Instructions for determining the adequacy of an

installation can be found in the current revision of the

NFGC (ANSI Z223.1 / NFPA54). Consult local codes

for special requirements. These requirements are for

US installations as found in the NFGC.

• The requirements in Canada (B149.1) are structured

differently. Consult with B149.1 and local code ofﬁ cials

for Canadian installations.

• Additional reference information for US and Canadian

installations can be found in the Combustion and

Ventilation Air section on page 4.

Air openings in the door of the unit, warm air registers, and

return air grilles must never be restricted. If the unit does

not receive an adequate supply of air for combustion, the

ﬂ ame roll-out control located above the burners will open,

turning off the gas supply to the burners. This safety device

is a manually reset switch. IMPORTANT NOTE: DO NOT

install jumper wires across this control to defeat its

function or reset the control without identifying and

correcting the fault condition.

If this control must be replaced, use only factory authorized

replacement parts speciﬁ ed in the Replacement Parts

List provided online.

CAUTION:

Appliances that force air from the building to

the outdoors can create negative pressures

inside, resulting in improper operation or unsafe

conditions. It is imperative that sufﬁ cient air

exchange with the outdoors is provided to prevent

depressurization.

Additional information about how to test for

negative pressure problems can be found in the

National Fuel Gas Code.

Figure 5. Rigging and Hoisting

LIFTING

BEAM

CABLE OR CHAIN

SPREADER

BAR

SPREADER

BAR

BASE

RAIL

BASE

RAIL

Rigging and Hoisting

WARNING:

To avoid the risk of property damage, personal

injury, or death, it is the rigger’s responsibility

to ensure that whatever means are used to hoist

the unit are safe and adequate:

• The lifting equipment must be adequate for

the load. Refer to Table 4 (page 27) for unit

weights.

• The unit must be lifted from the holes in the

base rails using cables or chains. Refer to

Figure 5 for example setup.

• Spreader bars are required to protect the unit

and ensure even loading (See Figure 5).

• Keep the unit in an upright position at all times.

The rigging must be located outside the units

center of gravity. Refer to Figures 12 - 14 (pages

22-27) for locating the center of gravity.

• All panels must be secured in place during

rigging and hoisting.

UNIT INSTALLATION

Packaging Removal

1. Remove top crate brackets and wooden cap assembly

from top of unit (Figure 3).

2. Remove lower crate brackets, 4 side skids, and 2 end

skids from each side of unit. NOTE: DO NOT remove

base rails from unit.

3. Rig unit and raise up approximately 4 feet off the ground.

(Also see Rigging and Hoisting section).

4. Remove crate brackets (Figure 4) securing long and

short bottom boards to underside of unit. NOTE: Some

screws are located in fork slots.

5. Remove long and short bottom boards from beneath

unit.

6. Inspect unit thoroughly for shipping damage.

7. Carefully lower and position unit to it’s permanent

location.

Figure 4. Bottom View

Crate Brackets (x4)

Long Bottom

Boards (x2)

Short Bottom

Boards (x2)

Base

Rails

Figure 3. Side View

Wood Cap

Assembly

Top Crate

Brackets

Lower

Crate

Brackets

End Skid

Side Skids

Top of unit

to be

unobstructed

Recommended Clearances

for Servicibility

Minimum Required

Clearances to Combustibles

36"

48"

60"

48"

Figure 6. Unit Clearance Requirements

Minimum Clearance Requirements

R6GP units are certiﬁ ed as combination heating and

cooling equipment for outdoor installation only. Figure 6

displays the minimum clearances to combustible materials

for both Downﬂ ow and Horizontal discharge.

R6GP units may be installed on non-combustible surfaces

when used with bottom supply and return air ducts.

Units may be installed on wood ﬂ ooring or on Class A,

B, or C roof covering material as long as the following

requirements are met:

• If using side supply with return air ducts, the

horizontal discharge kit must be installed prior to unit

installation.

• If using bottom discharge with return air ducts

a roof curb must be installed prior to unit

installation. See Rigging and Hoisting section on

page 8 for setting of the unit.

Rooftop Mounting

Rooftop installations must be located according to local

building codes or ordinances and these requirements:

• The roof must be capable of handling the weight of the

unit. For unit weights, see Table 4 (page 27). Reinforce

the roof if necessary.

• The appropriate accessory roof curb (Figure 7) must

be installed prior to unit installation. The roof curb

must be square and level to ensure proper condensate

drainage. Please follow all instructions provided

with the kit.

WARNING:

Never drill or punch holes in unit base when installing

downﬂ ow units. Leakage may occur if bottom pan is

punctured.

• On bottom discharge applications, the supply and

return air ducts must be attached to the roof curb duct

supports, not the unit. Install all ductwork before setting

unit on curb or frame.

• Frame support must be constructed using

noncombustible materials. Full perimeter support is

required under the unit. Supports must be made of

steel or weather resistant wooden materials. The unit

must be square and level to ensure proper condensate

drainage.

• The frame must be high enough to ensure prevention

of any moisture from entering the unit. Recommended

height to unit base is 8” (20cm) for both Downﬂ ow and

Horizontal installations.

• Secure roof curb or frame to roof using acceptable

mechanical methods per local codes.

Figure 8. Concrete Mounting Pad

3” min

Figure 7. Roof Curb

Roof Curb

Ground Level

Ground level installations must be located according to local

building codes or ordinances and these requirements:

• Clearances must be in accordance with those shown

in Figure 6.

• A concrete mounting pad (Figure 8) must be provided

and separate from the building foundation. The pad

must be level to ensure proper condensate disposal

and strong enough to support the unit’s weight. The

slab height must be a minimum of 3” (8cm) above grade

and with adequate drainage.

• Units require horizontal supply and return kit for

horizontal installations.

• Ductwork should be attached directly to ﬂ anges on

panels supplied in horizontal duct conversion kits.

CIRCULATING AIR SUPPLY

WARNING:

Do not allow combustion products to enter the

return air ductwork or the circulating air supply.

Failure to prevent the circulation of combustion

products into the occupied space can create

potentially hazardous conditions including

carbon monoxide poisoning that could result in

personal injury or death.

All return ductwork must be secured to the

unit with sheet metal screws. All joints must be

taped and adequately sealed. When return air

is provided through the bottom of the unit, the

joint between the unit and the return air plenum

must be air tight.

The roof curb or framing must provide sound

physical support of the unit with no gaps, cracks,

or sagging between the unit and the curb or

frame.

Return air and circulating air ductwork must

not be connected to any other heat producing

device such as a ﬁ replace insert, stove, etc. This

may result in ﬁ re, explosion, property damage,

personal injury, or death from carbon monoxide

poisoning.

This unit is designed only for use with a supply and return

duct. Any exterior ducts, joints, or openings in the building

roof or walls must be weatherized with conventional

ﬂ ashing and sealing compounds. Air ducts should be

installed in accordance with all applicable local codes and

the standards of the National Fire Protection Association

“Standard for Installation of Air Conditioning Systems”

(NFPA 90A).

Design the ductwork according to methods described

by the Air Conditioning Contractors of America (ACCA)

Manual Q .

It is recommended that the outlet duct be equipped

with a removable access panel. This opening should be

accessible when the unit is installed in service and shall

be of a size such that the smoke or reﬂ ected light may

be observed inside the casing to indicate the presence

of leaks in the heat exchanger. The cover for the opening

shall be attached in such a manner as to prevent leaks.

If outside air is used as return air for ventilation or to

improve indoor air quality, the system must be designed so

that the return air to the unit is not less than 50° F (10° C)

during heating operation. If a combination of indoor and

outdoor air is used, the ducts and damper system must

be designed so that the return air supply to the unit is

equal to the return air supply under normal, indoor return

air applications.

Additional reference information for US and Canadian

installations can be found in the Duct Systems section

on page 4.

Unconditioned Spaces

All ductwork passing through unconditioned space must be

properly insulated to prevent condensation and minimize

duct losses. Use insulation with an outer vapor barrier. Refer

to local codes for insulation material requirements.

Acoustical Ductwork

Certain installations may require acoustical lining inside

the supply ductwork. Acoustical insulation must be in

accordance with the current revision of the Sheet Metal

and Air Conditioning Contractors National Association

(SMACNA) application standard for duct liners. Duct lining

must be UL classiﬁ ed batts or blankets with a ﬁ re hazard

classiﬁ cation of FHC-25/50 or less.

Fiber ductwork may be used in place of internal duct

liners if the ﬁ ber ductwork is in accordance with the

current revision of the SMACNA construction standard

on ﬁ brous glass ducts.

Fibrous ductwork and internal acoustical lining must be

NFPA Class 1 air ducts when tested per UL Standard

181 for Class 1 ducts.

Downﬂ ow to Horizontal Conversion

The unit is shipped ready for downﬂ ow duct connections. If

horizontal ducts are required, the unit must be converted

according to the directions in the conversion kit for both

the supply and return ducts.

GAS SUPPLY AND PIPING

All gas piping must be installed in compliance with local

codes and utility regulations. In the absence of local codes

the gas line installation must comply with the latest edition

of the National Fuel Gas Code ANSI Z223.1 or CAN/CGA

B149 Installation Codes.

Additional reference information for US and Canadian

installations can be found in the Gas Piping and Gas Pipe

Pressure Testing section on page 4.

IMPORTANT NOTES:

• DO NOT run gas piping in or through air ducts, chimneys,

gas vents, elevator shafts, etc.

• Compounds used on threaded ends of gas piping

must be resistant to the actions of liqueﬁ ed petroleum

gases.

• The main gas valve and main power disconnect to the

unit must be properly labeled by the installer in case

emergency shutdown is required.

• A drip leg must be installed in the pipe run to the unit.

(Figure 9).

• An 1/8 inch NPT plugged tap must be installed in the gas

line immediately upstream of the gas supply connection

to the furnace for use when measuring the gas supply

pressure. The plug should be readily accessible for

service use.

Some local regulations require the installation of a manual

main shut-off valve and ground joint union external to the

unit. The shut-off valve should be readily accessible for

service and/or emergency use. Consult the local utility

or gas supplier for additional requirements regarding

placement of the manual main gas shut-off.

Table 14 (page 42), lists gas pipe capacities for standard

pipe sizes as a function of length in typical applications

based on nominal pressure drop in the line.

Figure 9. Typical Gas Service Connection.

1. All piping must comply with local codes, ordinances, and/or National Fuel Gas Codes.

2. A manual shutoff valve must be installed within 6 feet of this equipment.

3. Always include a drip leg in piping.

NOTES:

Gas Valve

Riser

3 in.

Minimum

Horizontal

Drop

Piped Gas Supply

Tubing Gas Supply

3 in.

Minimum

Horizontal

Drop

Gas Valve

3 in.

Min.

Riser

Piped Gas Supply

This unit only has right side gas entry. When connecting

the gas, provide clearance between the gas supply line

and the entry hole in the unit’s casing to avoid unwanted

noise and/or damage to the unit. A typical gas service

hookup is shown in Figure 9.

This unit is shipped from the factory for natural gas

operation at sea level elevation and is equipped with a

#36 oriﬁ ce at each burner.

Leak Check

WARNING:

FIRE OR EXPLOSION HAZARD

Never test for gas leaks with an open ﬂ ame. Check

all connections using a commercially available

soap solution. A ﬁ re or explosion may result

causing property damage, personal injury or

loss of life. Failure to follow the safety warnings

exactly could result in serious injury, death or

property damage.

After the gas piping to the unit is complete, all connections

must be tested for gas leaks. This includes pipe connec-

tions at the main gas valve, emergency shutoff valve and

other gas connectors. The soap and water solution can be

applied on each joint or union using a small paintbrush.

If any bubbling is observed, the connection is not sealed

adequately and must be retightened. Repeat the tightening

and soap check process until bubbling ceases.

IMPORTANT NOTES:

• If pressure testing the gas supply lines at pressures

greater than 1/2 psig (14 inches WC), the unit must

be disconnected from the gas supply piping system

to prevent damage to the gas valve.

• If the test pressure is less than or equal to 1/2 psig

(14 inches WC), the unit must be isolated from the

gas supply line by closing the manual shut-off

valve.

High Altitude Deration

High altitude application with this unit depends on the

installation altitude and the heating value of the gas. At

high altitudes, the heating value of natural gas is always

lower than the heating value at sea level.

All installations of this equipment must be made in

accordance with the National Fuel Gas Code or with

local jurisdiction codes. For installations at exactly

2,000 feet in altitude or under, the installer does not

need to derate the heat exchanger performance. For

any installation that exceeds 2,000 feet, please see the

following instructions and example:

WARNING:

The reduction of input rating necessary for high

altitude installation may only be accomplished

with factory supplied oriﬁ ces. Do not attempt to

drill out oriﬁ ces in the ﬁ eld. Improperly drilled

orifices may cause fire, explosion, carbon

monoxide poisoning, personal injury or death.

• If installing this unit above 2,000 feet, the input rate must

be reduced 4% per 1,000 feet of altitude (Example: 12%

at 3,000 feet, 16% at 4,000 feet, etc). Always round up

to the next highest value of 1,000. So an installation

at 3,120 feet is derated by 16% due to rounding up to

4,000. NOTE: This deration is necessary to compensate

for low atmospheric pressure at high altitudes. Generally

this will require obtaining the gas heating value from

the local gas utility and replacing the burner oriﬁ ces.

• Table 15 (page 42) lists the correct oriﬁ ce size to use

at different altitudes. See Installation Example 1 to

determine the unit rating and oriﬁ ce size.

• After changing the oriﬁ ces, it is required that you

measure the gas input rate by clocking the gas meter

and using the local gas heating value. See section on

Verifying and Adjusting the Firing Rate on page 15.

IMPORTANT NOTE: Observe the action of the

burners to make sure there is no yellowing, lifting

or ﬂ ashback of the ﬂ ame.

Conversion to LP/Propane

WARNING:

The furnace was shipped from the factory

equipped to operate on natural gas. Conversion

to LP/propane gas must be performed by

qualiﬁ ed service personnel using a factory

supplied conversion kit. Failure to use the proper

conversion kit can cause ﬁ re, explosion, property

damage, carbon monoxide poisoning, personal

injury, or death.

If installing the unit above 2,000 ft., refer to Table 15 to

determine the correct oriﬁ ce size. When conversion is

complete, verify the input rate is correct as listed in the

tables. Approved conversion kit must be used. Please

follow the instructions provided with each kit.

INSTALLATION EXAMPLE:

Elevation: ............................................ 3,890 feet

Type of Gas: ............................................Natural

Unit Model: .............................R6GP-090C200C

At 4,000 feet, the unit needs to be derated by 4% for

each 1,000 feet of elevation. This equates to 16% or

less than the sea level rating of 200,000 Btu/h.

1. Determine unit input rating:

[200k x (100-16)%] = 168,000 Btuh. The required

heating rate for 3,890 feet is 168,000 Btu/h.

2. Determine oriﬁ ce size:

From Table 15 (page 42), ﬁ nd the Unit Model

Number. Follow across the natural gas row and

stop at the 2,000-4,000 elevation column. For this

example, the oriﬁ ce size displayed is #38. Install

one #38 oriﬁ ce in every burner and check ﬁ ring

rate. The ﬁ ring rate in this example must not exceed

168,000 Btu/h.

ELECTRICAL WIRING

WARNING:

To avoid the risk of electrical shock, personal

injury, or death, disconnect all electrical power

to the unit before performing any maintenance

or service.

• Electrical connections must be in compliance with

all applicable local codes and ordinances, and with

the current revision of the National Electric Code

(ANSI/NFPA 70).

• For Canadian installations the electrical connections

and grounding shall comply with the current Canadian

Electrical Code (CSA C22.1 and/or local codes).

• Additional reference information for US and Canadian

installations can be found in the Electrical Connections

section on page 4.

Pre-Electrical Checklist:

√ Verify that the voltage, frequency, and phase of the

supply source match the speciﬁ cations on the unit

rating plate.

√ Verify that the service provided by the utility is sufﬁ cient

to handle the additional load imposed by this equipment.

See Table 13 (page 36) or the unit wiring label for proper

high and low voltage wiring.

√ Verify factory wiring is in accordance with the unit wiring

diagram. Inspect for loose connections.

√ For 3 phase units always check the phase balance

(page 12).

Line Voltage

It is recommended that the line voltage to the unit be

supplied from a dedicated branch circuit containing the

correct fuse or circuit breaker for the unit.

IMPORTANT NOTE: An electrical disconnect must

be installed readily accessible from and located

within sight of the unit. (See unit data label for proper

incoming ﬁ eld wiring). Any other wiring methods must

be acceptable to authority having jurisdiction.

The power supply for the unit must be in accordance with

the unit wiring diagram, and the unit rating plate. Connect

the line-voltage leads to the corresponding terminals on

the terminal block inside the control compartment. Use

only copper wire for the line voltage power supply to this

unit. Use proper code agency listed conduit and connector

for connecting the supply wires.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation. Verify proper

operation after servicing.

Units are shipped from the factory wired for 230 or 460

volt operation. On 208-230V units being placed into 208

volt operation, remove the lead from the transformer

terminal marked 240V and connect it to the terminal

marked 208V.

Overcurrent protection must be provided at the branch

circuit distribution panel and sized as shown on the unit

rating label and according to the National Electric Code

and applicable local codes. NOTE: See the unit rating plate

for maximum circuit ampacity and maximum overcurrent

protection limits.

Grounding

WARNING:

The unit cabinet must have an uninterrupted or

unbroken electrical ground to minimize personal

injury if an electrical fault should occur. Do not

use gas piping as an electrical ground

This unit must be electrically grounded in accordance

with local codes or, in the absence of local codes, with

the National Electrical Code (ANSI/NFPA 70) or the CSA

C22.1 Electrical Code. Use the grounding lug provided in

the control box for grounding the unit.

Example:

AB = 451V

BC = 460V

AC = 453V

2. Determine the average voltage in the power supply.

3. Determine the maximum deviation:

4. Determine percent of

voltage imbalance by

using the results from

steps 2 & 3 in the following

equation.

max voltage deviation

from average voltage

=100x

average voltage

% Voltage Imbalance

454

100

= 1.32%

Example:

1. Measure the line voltages

of your 3-phase power

supply where it enters the

building and at a location

that will only be dedicated

to the unit installation. (at

the units circuit protection

or disconnect).

Unbalanced 3-Phase Supply Voltage

Voltage unbalance occurs when the voltages of all phases

of a 3-phase power supply are no longer equal. This

unbalance reduces motor efﬁ ciency and performance.

Some underlying causes of voltage unbalance may include:

Lack of symmetry in transmission lines, large single-phase

loads, and unbalanced or overloaded transformers. A

motor should never be operated when a phase imbalance

in supply is greater than 2%.

Perform the following steps to determine the percentage

of voltage imbalance:

In this example, the measured line voltages were

451, 460, and 453. The average would be 454 volts

(451 + 460 + 453 = 1,364 / 3 = 454).

The amount of phase imbalance (1.32%) is satisfactory

since the amount is lower than the maximum allowable

2%. Please contact your local electric utility company if

your voltage imbalance is more than 2%.

Example:

From the values given in step 1, the BC voltage

(460V) is the greatest difference in value from

the average:

460 - 454 = 6

454 - 451 = 3

454 - 453 = 1

Highest Value

Blower Speed

The blower speed is preset at the factory but must

be veriﬁ ed at each installation. For optimum system

performance and comfort, it may be necessary to change

the factory set speed. Refer to Blower Performance Data

(Tables 5 - 12, pages 28 - 35) for proper operating range.

Always ensure drive belt is secure and tensioned properly.

Also inspect variable pitch sheaves for proper tightness

of the set screws

CAUTION:

To avoid personal injury or property damage,

make certain that the motor leads do not make

contact with any uninsulated metal components

of the unit.

To change the blower speed:

1. Disconnect all electrical power to the unit and remove

the blower access panel.

2. Loosen the motor tension bars to allow removal of the

blower belt from the motor sheave.

3. Loosen top set screw on motor sheave and turn

clockwise to close (increases blower speed), or

counterclockwise to open (decreases blower speed).

4. Replace belt on pulleys and position motor mounting

plate to correct position for proper belt tension.

5. Tighten tension bar bolts.

Thermostat

A two-stage heating/cooling thermostat is required for

R6GP series units. Select a thermostat which operates

in conjunction with the installed accessories. See Figure

10 for proper wire gauge and their recommended lengths

for typical thermostat connections.

The thermostat should be mounted about ﬁ ve feet above

the ﬂ oor on an inside wall.

IMPORTANT NOTE: DO NOT install the thermostat

on an outside wall or any other location where its

operation may be adversely affected by radiant heat

from ﬁ replaces, sunlight, or lighting ﬁ xtures, and

convective heat from warm air registers or electrical

appliances. Refer to the thermostat manufacturer’s

instruction sheet for detailed mounting and installation

information.

Heat Anticipator

Verify if the thermostat being used for the installation has a

heat anticipator setting. This function allows the thermostat

to anticipate the space heating rate and time the burner

to shutoff accordingly. Always refer to the thermostat

manufacturers instructions for the correct settings.

Figure 10. Typical Connections - 2 Stage

Heat/Cool T-Stat

Indoor

Thermostat

Sub-Base

Unit Low Voltage

Terminal

T-Stat Wire

Gauge

Recommended T-Stat Wire

Length - Ft. (Unit to T-Stat)

18 Ga. 0 - 60

16 Ga. 61 - 130

Field Supplied Wiring - - - - - Use Solid Class II Copper Wire

STARTUP AND ADJUSTMENTS

Pre-Start Check List

√ Verify unit is properly supported.

√ Verify unit is level for proper condensate drainage.

√ Verify all clearance requirements are met. Airﬂ ow to

and from the outdoor coil must be unrestricted.

√ Verify the ductwork is adequately sealed to prevent air

leakage. Insulate if necessary.

√ Verify the line voltage power leads are securely

connected and the unit is properly grounded.

√ Verify low voltage wires are securely connected to

the correct leads in the low voltage area of the control

box.

√ Verify gas line pressure. For natural gas, the line

pressure must not exceed 10.0 inches WC (0.36 psig),

or be less than 5.5 inches WC (0.20 psig). For LP gas,

the line pressure must not exceed 14 inches WC (0.51

psig) and must not be less than 11.0 inches WC (0.40

psig).

√ Verify the flame roll-out control is closed.

IMPORTANT NOTE: This safety device is a manually

reset switch. If necessary, press the red button to

reset the control. DO NOT install a jumper wire

across the control to defeat its function. If the

control reopens upon start-up, DO NOT reset the

control without identifying and correcting the fault

condition which caused the control to trip.

√ Verify the gas line has been purged and all connections

are adequately sealed. To check for gas leakage, see

Leak Check section on page 10.

√ Verify the indoor blower is properly set for the

installation.

√ Verify the outdoor fan turns freely.

√ Verify the power supply branch circuit overcurrent

protection is properly sized.

√ Verify all exterior panels have been reinstalled and

securely fastened.

√ Verify the thermostat is wired correctly and preset for

initial operation. Set the thermostat system switch to

OFF and the fan switch to AUTO.

Startup Procedures

WARNING:

This unit is equipped with crankcase heaters.

Allow 24 hrs for heating of the refrigerant

compressor crankcase prior to start up and

anytime the power has been removed for more

than 12 hrs. Failure to comply may result in damage

or cause premature failure of the system.

• Check all electrical wiring for loose connections and

tighten as required.

• Check unit for return air ﬁ lters and condensate trap.

• Close all electrical disconnects to energize the

system.

Air Circulation

1. Set thermostat system switch to OFF and the fan switch

to ON.

2. Verify the blower motor runs continuously. Check for

air delivery at the register(s). Ensure that there are no

obstructions at the registers or in the ductwork.

3. Set thermostat fan switch to AUTO and verify the blower

shuts down immediately.

NOTE: If blower is turning opposite of arrow direction, shut

off main power to the unit and switch any two ﬁ eld wires

at the disconnect. DO NOT alter unit wiring.

System Cooling

1. Set the thermostat system switch to COOL and the fan

switch to AUTO.

2. Lower the thermostat temperature switch below

room temperature and observe that the blower, both

compressors and fans) energize.

3. Verify blower is turning in direction indicated by arrow

and air discharged at the register is cooler than room

temperature.

4. Verify HI and LO refrigerant pressures.

NOTE: If refrigerant pressures are abnormal and blower

is rotating in the opposite direction of the arrow, shut off

main power to the unit and switch any two ﬁ eld wires at

the disconnect. Ensure proper rotation of the blower. DO

NOT alter unit wiring. Listen for any unusual noises. Locate

the source and correct as needed.

5. Allow the unit to run for several minutes. Set the

temperature selector above room temperature and

verify that the fan, blower, and compressors cycle off

with the thermostat.

System Heating

1. Set the thermostat to the lowest setting.

2. Follow the startup procedures on this page or the

operating instruction label inside the louvered control

access panel.

3. Set the thermostat above room temperature and verify

the Operating Sequence (page 16).

4. Verify that the compressor and outdoor fan motor are

not energized.

5. Run the unit and after approximately ﬁ ve minutes, set

the thermostat below room temperature. Verify the

shutdown sequence (see Operating Sequence).

Verifying and Adjusting Temperature Rise

Verify the temperature rise through the unit is within the

range speciﬁ ed on the unit data label. Temperature rises

outside the speciﬁ ed range could result in premature heat

exchanger failure.

1. Place thermometers in the return and supply air stream

as close to the unit as possible. The thermometer on the

supply air side must be shielded against direct radiation

from the heat exchanger to avoid false readings.

2. Adjust all registers and duct dampers to the desired

position. Run the unit for 10 to 15 minutes before

taking any temperature readings. The temperature

rise is the difference between the supply and return

air temperatures.

NOTE: For typical duct systems, the temperature rise will

fall within the range speciﬁ ed on the data label (with the

blower speed at the factory recommended setting) shown

in Table 16, page 42. If the measured temperature rise falls

outside the speciﬁ ed range, it may be necessary to change

the blower speed. Lowering the blower speed increases

the temperature rise and a higher speed decreases the

temperature rise.

The unit is equipped with a belt driven blower and variable

pitch motor sheave. The selection of a sheave setting

should be based on the desired CFM and the duct system

parameters. Refer to the ACCA’s Manual Q for a complete

description of how to determine these parameters and

Manual N for determination of the commercial load

requirements. The blower performance data can be found

in Tables 5 - 12 (pages 28 - 35).

For 7 1/2 and 10 ton units, the integrated control is designed

to start the circulating air blower 45 seconds after the gas

valve opens and designed to turn the blower motor off 150

seconds after the gas valve is closed.

For 6 ton units, the integrated control is designed to start

the circulating air blower 40 seconds after the gas valve

opens and turn the blower motor off 150 seconds after

the gas valve is closed

Verifying Burner Operation

WARNING:

Uninsulated live components are exposed when

the louvered control access panel is removed.

1. Remove the louvered control access panel to ensure

there is power to the unit.

2. Set the thermostat above room temperature and

observe the ignition sequence. The burner ﬂ ame should

carry over immediately between all burners and should

extend from each burner without lifting off, curling, or

ﬂ oating. The ﬂ ames should be blue, without yellow

tips.

3. After verifying ﬂ ame characteristics, set the thermostat

below room temperature and verify that the burner

ﬂ ame extinguishes completely.

Verifying Operation of Over-Temperature Limit

Control

To verify operation of the over-temperature limit control,

make sure the louvered control access panel is in place

and that there is power to the unit.

1. Block the return airﬂ ow to the unit by installing a close-

off plate in place of or upstream of the ﬁ lter.

2. Set the thermostat above room temperature and verify

the unit operates with the correct sequence of operation

(see Operating Sequence).

NOTE: The over-temperature limit control should function

to turn off the gas valve within approximately four minutes

(exact time depends on the efﬁ ciency of the close-off when

blocking the return air). The circulating air and combustion

blowers should continue to run when the over-temperature

limit control switch opens.

3. Remove the close-off plate immediately after the over-

temperature limit control opens. If the unit operates

for more than four minutes with no return air, set the

thermostat below room temperature, shut off power

to the unit, and replace the over-temperature limit

control.

Verifying and Adjusting Firing Rate

The ﬁ ring rate must be veriﬁ ed for each installation to

prevent over-ﬁ ring of the unit.

CAUTION:

Do not re-drill the burner oriﬁ ces. If the oriﬁ ce

size must be changed, use only new oriﬁ ces.

IMPORTANT NOTE: The ﬁ ring rate must not exceed

the rate shown on the unit data label. At altitudes

above 2,000 ft., it must not exceed that on the data

label less 4% for each 1,000 ft.

Follow the steps below to determine the unit ﬁ ring rate:

• For installations at 2,000 feet and less, the ﬁ ring rate

is the same as shown on the unit rating label.

• For installations above 2,000 feet, compute the correct

ﬁ ring rate as shown in the installation example on

page 11.

1. Obtain the gas heating value from the gas supplier

(HHV).

2. Shut off all other gas ﬁ red appliances.

3. Start the unit in heating mode and allow it to run for at

least three minutes.

4. Measure the time (in seconds) required for the gas

meter to complete one revolution.

5. Convert the time per revolution to cubic feet of gas per

hour using Table 17 (page 43).

6. Multiply the gas ﬂ ow rate in cubic feet per hour by the

heating value of the gas in Btu per cubic foot to obtain

the ﬁ ring rate in Btu per hour. See Example:

Example:

• Time for 1 revolution of a gas meter with a 1

cubic foot dial = 40 seconds.

• From Table 17 read 90 cubic feet gas per hour.

• Local heating value of the gas (obtained from

gas supplier) = 1,040 Btu per cubic foot.

• Input rate = 1,040 x 90 = 93,600 Btuh.

7. Adjustments to the ﬁ ring rate can be made by adjusting

the gas manifold pressure. See the High Altitude

Deration section (page 10) for additional information

of ﬁ ring rate at elevations above 2000 ft.

The manifold pressure must be set to the appropriate

value for your installation. Refer to Table 15 (page 42)

for the correct oriﬁ ce size and manifold pressure setting

required for your particular installation. To adjust the

manifold pressure, remove the regulator cap and turn

the adjusting screw clockwise to increase pressure

or counterclockwise to reduce pressure. Replace the

regulator cap after adjustments are complete.

OPERATING SEQUENCE

The operating sequences for the heating, cooling, and

fan modes are described below. Refer to the wiring

diagrams (Figures 15 - 19, pages 37 - 41).

Cooling Mode:

1. On a call for cooling the thermostat closes, applying

24 VAC to “Y1”, “G”, and “Y2” if Stage 2 cooling is

calling.

2. “G” applies 24VAC to the main circulating blower

circuit.

3. “Y1” and “Y2” apply 24VAC through all safety switches

before energizing their respective contactors.

4. When the thermostat is satisﬁ ed the contactors are

de-energized.

5. The circulating blower motor de-energizes

immediately.

Heating Mode for 200 & 235 kBtuh Heat

Exchangers:

1. On a call for heat, the thermostat closes, applying 24

VAC to the “W1” terminal (and “W2” terminal if Stage 2

heat is required). NOTE: There is a three minute time

delay before Stage 2 heat is energized.

2. The integrated control monitors the safety circuit at all

times. If either the roll-out switch or the over-temperature

limit controls open, the gas valve will not energize.

The main blower continues to operate until the over-

temperature limits close, the ﬂ ame roll-out switch is

manually reset, or the thermostat is satisﬁ ed.

3. The integrated control checks all safety switches at

the beginning of each heating cycle. If closed, the

combustion blower performs a 15 second pre-purge.

4. The integrated control will then supply power to the

direct spark ignitor and immediately energizes the gas

valve.

5. The ﬂ ame must be proven through the ﬂ ame sensor in

7 seconds to hold the gas valve open. The integrated

control will monitor the gas ﬂ ame with the ﬂ ame sensor

for the entire time the gas valve is open. If for any reason

the gas ﬂ ame drops out, the gas valve will immediately

close. After 30 second purge, the integrated control will

try to ignite two more times.

6. The main air blower will start and continue to run 45

seconds after the gas valve opens.

7. When the thermostat is satisﬁ ed, the integrated control

is de-energized. The gas valve and combustion blower

de-energize immediately while the main air blower

continues to run through the blower off delay of 150

seconds.

8. If the unit fails to prove ﬂ ame after three ignition attempts,

it will go into a soft lockout. The unit will re-attempt the

start-up procedure every hour until the thermostat is

satisﬁ ed or 24 VAC power is removed from the unit for

a minimum period of 5 seconds.

Heating Mode for 100 & 166 kBtuh Heat

Exchangers:

1. On a call for heat, the thermostat closes, applying 24

VAC to the W1 terminal (and W2 terminal if Stage 2

heat is required).

2. The integrated control monitors the safety circuit at all

times. If either the roll-out switch or the over-temperature

limit controls open, the gas valve will not energize.

The main blower continues to operate until the over-

temperature limits close, the ﬂ ame roll-out switch is

manually reset, or the thermostat is satisﬁ ed.

3. The integrated control checks all safety switches at

the beginning of each heating cycle. If closed, the

combustion blower performs a 10 second pre-purge.

4. The integrated control will then supply power to the

direct spark ignitor and immediately energizes the gas

valve. NOTE: Burner operation begins in high ﬁ re mode

with both Stage 1 and Stage 2 gas valve energized,

independent of the thermostat call for Stage 2 heat.

If after 30 seconds of operation with no call for Stage

2 heat, the integrated control will resume heating

operation in low ﬁ re mode of operation and Stage 2

gas valve is de-energized.

5. The ﬂ ame must be proven through the ﬂ ame sensor in

10 seconds to hold the gas valve open. The integrated

control will monitor the gas ﬂ ame with the ﬂ ame sensor

for the entire time the gas valve is open. If for any reason

the gas ﬂ ame drops out, the gas valve will immediately

close. After 30 second purge, the integrated control will

try to ignite fourteen more times.

6. The main air blower will start and continue to run 40

seconds after the gas valve opens.

7. When the thermostat is satisﬁ ed, the integrated

control is de-energized. The gas valve and combustion

blower de-energize immediately while the main air

blower continues to run through the blower off delay

of approximately 150 seconds.

8. If the unit fails to prove ﬂ ame after ﬁ fteen ignition

attempts, it will go into a soft lockout. The unit will

re-attempt the start-up procedure every hour until the

thermostat is satisﬁ ed or 24 VAC power is removed

from the unit for a minimum period of 5 seconds.

NOTE: See Table 2 (page 17) or Figure 15 (page 37)

for a complete list of heating operation fault codes.

Blower Mode:

1. On a call for fan operation, the thermostat applies 24

VAC directly to the blower contactor.

2. The circulating blower is energized immediately.

TROUBLESHOOTING

If the unit does not operate properly in the cooling

mode, check the following:

• The thermostat is operating properly.

• Electrical power to the unit is turned on.

• All safety switches are closed.

• The service doors are in place.

• Transformer circuit breaker is reset.

If the unit does not operate properly in the heating

mode, check the following:

• The thermostat is operating properly.

• Electrical power to the unit is turned on.

• All safety switches are closed.

• The gas is on and shut-off valve is open.

• The service doors are in place.

• The ﬂ ame roll-out control is closed.

• Refer to the diagnostic codes in Tables 1 or 2, or the

wiring diagrams (Figures 15 - 19, pages 37 - 41).

• Transformer circuit breaker is reset.

Table 1. Diagnostic Codes For 7 1/2 & 10 Ton Units

STATUS LIGHT

(RED)

FAULT

CONDITION

Continuous ON Internal Control Failure

2 Flashes Flame Sense Problem

3 Flashes Ignition Lockout

STATUS LIGHT

(Red LED)

FAULT

CONDITION

Continuous ON Operation Normal

2 Flashes

Pressure/centrifugal switch open

with inducer on

3 Flashes

Pressure/centrifugal switch closed

with inducer off

4 Flashes

Lockout from too many

failed ignition tries

5 Flashes

Lockout from too many

ﬂ ame losses

6 Flashes High temperature switch open

7 Flashes Rollout switch open

8 Flashes Flame present with gas off

9 Flashes

Exceeded max limit trips (5)

in one call for heat

10 Flashes Gas valve fault

Table 2. Diagnostic Codes For 6 Ton Units

UNIT MAINTENANCE

NOTE: These maintenance instructions are primarily

intended to assist qualiﬁ ed technicians experienced in the

proper maintenance and operation of this appliance.

To achieve optimum performance from the air conditioner

and minimize equipment failure, it is recommended

that periodic maintenance be performed on this unit.

The ability to properly perform maintenance on this

equipment requires certain mechanical skills and tools.

Please consult your dealer for maintenance information

and availability of maintenance contracts.

CAUTION:

Use care when removing parts from this unit.

Personal injury can result from sharp metal

edges present in all equipment of sheet metal

construction.

At a minimum, routine maintenance should include the

following items:

Condensate Drain and Outdoor Coil

Inspect the condensate drain and outdoor coil at the

beginning of each cooling season. Remove any debris.

Clean the outdoor coil and hail guard louvers (optional)

as necessary using a mild detergent and water. Rinse

thoroughly with water.

Air Filters

WARNING:

Never operate the unit without ﬁ lters in place. Dust

and lint in the return air can build up on internal

components, resulting in loss of efﬁ ciency,

equipment damage, and possible ﬁ re.

It is recommended that the air ﬁ lters be inspected and

cleaned or replaced every three to four weeks using ﬁ lters

of like size and kind. Table 3 lists the correct ﬁ lter sizes

and quantities for each unit.

IMPORTANT NOTE: R6GP units are equipped with 2”

pleated disposable ﬁ lters. Filter rack is adjustable for

1” permanent type ﬁ lters. DO NOT use 1” disposable

ﬁ lters.

UNIT

FACTORY

FILTER

SIZE

QTY

R6GP-072*-(100/166)C 16x20x2 4

R6GP-090*-200C 16x20x2 4

R6GP-120*-235C 16x25x2 4

Table 3. Filter Sizes and Quantities

8. Remove four screws securing the burner assembly to

the unit.

9. Carefully remove the burner assembly from the unit.

DO NOT DAMAGE THE IGNITOR WHILE REMOVING

THE BURNER ASSEMBLY.

10. Inspect the burners for accumulated dust or debris.

If necessary, carefully clean them with a soft wire

brush and/or the nozzle of a vacuum cleaner. DO

NOT DAMAGE THE IGNITOR OR FLAME SENSOR

WHILE CLEANING THE BURNER.

11. Replace all the parts in reverse order from which they

were removed.

12. Follow the lighting instructions found on the right

side door to return the unit to operation. Verify proper

operation after servicing.

Cleaning of Heat Exchanger

If the heat exchanger must be cleaned due to soot or

scale build up, follow the steps below.

1. Shut off the gas supply to the unit either at the meter

or at the manual valve in the gas supply piping.

2. Turn off all power to the unit and set the thermostat to

the lowest temperature setting.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

3. Disconnect the wires from the gas valve, ignitor, and

ﬂ ame sensor.

4. Using two wrenches, separate the ground-joint union

in the gas supply piping at the unit.

5. Remove the piping between the gas valve and the

ground-joint union, if necessary.

6. Remove the four screws securing the burner assembly

to the unit.

7. Carefully remove the burner assembly from the unit. DO

NOT DAMAGE THE IGNITOR OR FLAME SENSOR

WHILE REMOVING THE BURNER ASSEMBLY.

8. Remove three nuts securing the combustion blower to

the collector pan.

9. Remove the complete combustion blower from the

unit.

10. Remove the screws securing the collector box cover

to the unit and remove cover plate.

11. Remove the screws securing the balance plate to the

collector box and the balance plate.

12. Remove the turbulator from each heat exchanger

tube.

13. Attach a round wire brush to a length of high grade

stainless steel cable, such as drain cleanout cable.

Attach the other end of the spring cable to a variable

speed reversible drill. Slowly insert and rotate the cable

into the top portion of the heat exchanger. Operate

Blower Compartment

Build up of dirt and lint on the blower and motor can create

excessive loads on the motor resulting in higher than

normal operating temperatures and possible shortened

service life. It is recommended that the blower compartment

be cleaned monthly during heating and cooling seasons

to remove any dirt and lint that may have accumulated in

the compartment or on the blower and motor. Inspect the

blower drive belt for cracks, excessive wear and proper

tension after cleaning the compartment.

Heat Exchanger and Burner Maintenance

The unit should operate for many years without excessive

scale buildup in the heat exchanger, however, the heat

exchanger, the vent system, and the burners should be

inspected and cleaned (if required) by a qualiﬁ ed technician

annually to ensure continued safe operation. Particular

attention must be given to identify deterioration from

corrosion or other sources.

WARNING:

Holes in the heat exchanger can cause products

of combustion to enter the structure. Replace

the heat exchanger if leaks are found. Failure

to prevent products of combustion from being

circulated into the occupied space can create

potentially hazardous conditions including

carbon monoxide poisoning that could result in

personal injury or death.

Cleaning of Burners

It is recommended that the burners be inspected and

cleaned periodically (if required) by a qualiﬁ ed technician

annually to ensure continued safe operation. Particular

attention must be given to identify deterioration from

corrosion or other sources. If the burners must be cleaned,

follow the steps below.

1. Shut off the gas supply to the unit either at the meter

or at a manual valve in the supply piping.

2. Turn off all power to the unit and set the thermostat to

the lowest temperature setting.

3. Remove the louvered access panel from the unit.

4. Turn the gas control knob to the “OFF” position.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

5. Disconnect the wires from the gas valve, ignitor, and

ﬂ ame sensor.

6. Using two wrenches, separate the ground-joint union

in the gas supply piping at the unit.

7. Remove the piping between the gas valve and the

ground-joint union (if necessary).

the drill alternating between forward and reverse,

working the cable in and out several times to obtain

sufﬁ cient cleaning. Repeat this sequence for each

heat exchanger tube.

14. Remove all loosened debris from the heat exchanger

tubes using a vacuum cleaner.

15. Using a light, check the condition of the upper and

lower sections of the heat exchanger tube.

16. Inspect the burners and if necessary, clean them

carefully with a soft wire brush and/or the nozzle of

a vacuum cleaner. DO NOT DAMAGE THE IGNITOR

OR FLAME SENSOR WHILE CLEANING THE

BURNER.

17. Replace all the parts in reverse order from which they

were removed. NOTE: If screws or other hardware

are corroded, replace only with corrosion resistant

stainless steel hardware of similar design.

18. Follow the operating instructions found on the right

side door and the User’s Information Manual to return

the unit to operation.

Vent Cover Assembly

Inspect and clean the screen of the vent cover assembly

at the beginning of each heating and cooling seasons.

Electrical

WARNING:

This unit may have more than one electrical

supply. To avoid risk of electrical shock, personal

injury, or death, disconnect all electrical power

to the unit before performing any maintenance

or service.

Inspect the electrical connections for tightness at the

beginning of each heating and cooling season. Service

as necessary.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

Motor Lubrication

The motors for the circulating air blower, outdoor fan, and

combustion blower are pre-lubricated at the factory. No

further oiling is required for the life of this product.

WARNING:

Lubrication of the motors in this unit is not

required. Do not lubricate any motor in this

product.

Refrigerant Charging

The R6 Series packaged gas/electric units are fully charged

at the factory and when installed accordingly, no charging

is required. The refrigerant charge can be checked and

adjusted through the service ports provided on the units.

Use only gauge lines which have a “Schrader” depression

device present to actuate the valve. Refer to Figures 20

- 22 (pages 44 - 45)

Refrigerant charging must be done by qualiﬁ ed personnel

familiar with safe and environmentally responsible

refrigerant handling procedures. See Unit Rating Plate

for the proper type and amount of refrigerant.

WARNING:

If repairs make it necessary for evacuation and

charging, it should only be done by qualiﬁ ed,

trained personnel thoroughly familiar with this

equipment. Some local codes require licensed

installation/service personnel to service this type

of equipment. Under no circumstances should

the owner attempt to install and/or service this

equipment.

Failure to comply with this warning could result

in property damage, personal injury, or death.

COMPONENT FUNCTIONS

The descriptions below are various functional components

that affect the operation and shutting down of this unit.

Some of these components and their locations are shown

in Figure 11 (page 21).

If any component on this unit must be replaced, use only

factory authorized replacement parts speciﬁ ed in the

Replacement Parts List provided online.

Centrifugal Switch

The centrifugal switch acts to verify that the inducer motor

is running. Combustion gases are drawn through the heat

exchanger tubes and vented through the vent system.

Flame Roll-Out Control

The ﬂ ame roll-out control acts to verify that the burner

ﬂ ame is being drawn into the heat exchanger tubes. If the

burner ﬂ ame is not being drawn into the heat exchanger

tubes, the roll-out control will open within several seconds.

The combustion blower will continue to operate if the ﬂ ame

roll-out control opens until it is manually reset.

Flame Sensor

The ﬂ ame sensor acts to prove that ﬂ ame has carried

over from the ignitor to the right-most burner. If no ﬂ ame

is sensed, the unit will be shut down automatically and

attempt two additional ignition trials before going into

lockout. Recovery from lockout requires a manual reset

by either resetting the thermostat or removing 24 volts

for a period of 5 seconds. If the thermostat is still calling

for heat after one hour the control will automatically reset

and attempt to ignite the burner again.

Gas Valve

The gas valve controls the ﬂ ow of gas to the burners in

both low and high ﬁ re. When the valve is energized, it

automatically opens and regulates the gas pressure to

the manifold.

High Pressure Switch

This factory installed switch is designed to de-energize

the unit when excessive pressure occurs due to abnormal

conditions. Under normal conditions, the switch is closed.

If the discharge pressure rises above 650 psig, then the

switch will open and de-energize the outdoor unit. The

switch is a manually reset type and will remain open until

the button on top of the switch is depressed.

Indoor Coil, Freeze Protection Thermostats

The freeze protection switches are designed to protect the

indoor coils from ice and frost accumulations in the event

of a loss of airﬂ ow by preventing the liquid refrigerant from

reaching the compressors. During normal operation, the

switches are closed and will open if the coil temperature

reaches 28° F (-2° C). The switches will close if the coil

temperature reaches 57° F (12° C).

Low Pressure Switch

This factory installed switch is designed to protect the

compressor from a loss of charge. Under normal conditions,

the switch is closed. If the suction pressure falls below 5

psig, then the switch will open and de-energize the outdoor

unit. The switch will close again once the suction pressure

increases above 20 psig.

Over-Temperature Limit Control

The over-temperature limit control acts to prevent the

air temperature leaving the unit from exceeding the

maximum outlet air temperature. If the limit opens, the

blower limit relay will energize. The circulating air blower

and combustion blower will continue to operate if the

over-temperature limit control opens.

La page est en cours de chargement...

Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Guide d'installation

Marque: Mammoth

Modèle: R6GP 6, 7.5 - 10 Ton Archived 2/23/12

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Installation guide

Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Guide d'installation

Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents