Eaton Pulsar EX 1500 Installation and User Manual

www.eaton.com

Installation and User Manual

Manuel d’installation et

d’utilisation

Manual de instalación y de

usuario

Manual de instalação e do

usuário

English

Français

Español

Portuguese

EX

700 – 1000 – 1500

1000 RT2U – 1500 RT2U

EXB 1000/1500

EXB 1000/1500 RT2U

Pulsar Series

For Technical Support, Customer Care Center, or Customer FAQ,

please call us at (800) 356-5794, or visit our website: www.eaton.com

www.eaton.com

EX

700 – 1000 – 1500

1000 RT2U – 1500 RT2U

EXB 1000/1500

EXB 1000/1500 RT2U

Installation and User Manual

Pulsar Series

86-86700-00EN A02 - Page 2

Contents

Introduction ....................................................................................................................... 5

Important Safety Instructions ............................................................................................ 6

Symbol Usage ................................................................................................................... 7

1. Presentation

1.1 Standard Positions ............................................................................................................. 8

1.2 Rear Panels........................................................................................................................ 9

1.3 Control Panel ................................................................................................................... 10

2. Installation

2.1 Unpacking and Contents Check ...................................................................................... 11

2.2 Installation of the RT Model in Tower Position ............................................................... 12

2.3 Installation of the RT Model in a Rack ............................................................................ 12

2.4 Communication Ports ...................................................................................................... 13

2.5 Connection to the Communication Port by Contact (2) .................................................. 14

2.6 Connections with a FlexPDU module ............................................................................. 15

2.7 UPS Connection .............................................................................................................. 15

3. Operation

3.1 Start-Up and Normal Operation ....................................................................................... 17

3.2 Operation on Battery Power ............................................................................................ 17

3.3 Return of AC Power ........................................................................................................ 18

3.4 UPS Shutdown ................................................................................................................ 18

3.5 Using the UPS Remote Control Functions ...................................................................... 18

4. Access to Measurements and Personalization Data

4.1 Display Menus Arrangement ........................................................................................... 21

4.2 Access to Measurements ............................................................................................... 21

4.3 Personalization Using the Control Panel ......................................................................... 21

4.4 Personalization Using External Software ......................................................................... 22

5. Maintenance

5.1 Troubleshooting ............................................................................................................... 23

5.2 Battery-module Replacement .......................................................................................... 24

6. Appendices

6.1 Technical Specifications .................................................................................................. 27

6.2 Programming the Programmable Outlets ....................................................................... 28

6.3 Glossary ........................................................................................................................... 30

86-86700-00EN A02 - Page 3

86-86700-00EN A02 - Page 4

Introduction

Thank you for selecting an EATON product to protect your electrical equipment.

EX has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of the many features of your UPS

(Uninterruptible Power Supply).

Before installing EX, please read the booklet on the required safety instructions. Then follow the indications in this

manual.

To discover the entire range of EATON products and the options available for the EX range, we invite you to visit our web

site at www.eaton.com or contact your EATON representative.

Environmental protection

EATON has implemented an environmental-protection policy.

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs, or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing components.

w The cardboard we use comprises over 50% of recycled cardboard.

w Sacks and bags are made of polyethylene.

w Packing materials are recyclable and bear the appropriate identification symbol.

Follow all local regulations for the disposal of packing materials.

End of life

EATON will process products at the end of their service life in compliance with local regulations.

EATON works with companies in charge of collecting and eliminating our products at the end of their service life.

w Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local regulations concerning waste.

At the end of its service life, the product must be transported to a processing center for electrical and electronic waste.

w Battery

The product contains lead-acid batteries that must be processed according to applicable local regulations concerning

batteries.

The battery may be removed and disposed of in compliance with correct local disposal regulations.

The “Material Safety Data Sheets” (MSDS) for the batteries are available on our web site*.

(*) For more information or to contact the Product Environmental manager, please visit our website:

www.eaton.com/pulsar.

Material Abbreviation

Symbol

number

Polyethylene terephthalate PET 01

High-density polyethylene HDPE 02

Polyvinyl chloride PVC 03

Low-density polyethylene LDPE 04

Polypropylene PP 05

Polystyrene PS 06

01

PET

01

PET

86-86700-00EN A02 - Page 5

86-86700-00EN A02 - Page 6

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be followed during installa-

tion and maintenance of the UPS and batteries.

The EX models that are covered in this manual are intended for installation in an environment within 0° to 40°C (32°F to

104°F), free of conductive contaminant.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Certification Standards

w IEEE 587-1980/ANSI C62.41 1980 Standards for Surge Withstand Ability

w FCC rules and regulations of Part 15, Subpart J, Class A

w UL listed under 1778, Standards for Uninterruptible Power Supply Equipment

w IEC 61000-4-2 (ESD): level 4

w IEC 61000-4-3 (Radiated field): level 3

w IEC 61000-4-4 (EFT): level 4

w IEC 61000-4-5 (Fast transients): level 4

w IEEE-C6241 Category B (ring wave)

w IEC 61000-4-6 (electromagnetic field)

w IEC 61000-4-8 (conducted magnetic field)

Safety of Persons

w

The system has its own power source (the battery). Consequently, the power outlets may be energized even if the systems is

disconnected from the AC power source.

w

Dangerous voltage levels are present within the system. It should be opened exclusively by qualified service personnel.

w

The system must be properly grounded.

w

The battery supplied with the system contains small amounts of toxic materials. To avoid accidents, the directives listed below

must be observed:

- Never burn the battery (risk of explosion).

- Do not attempt to open the battery (the electrolyte is dangerous for the eyes and skin).

- Comply with all applicable regulations for the disposal of the battery.

-

Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be

taken for all handling: remove watches, rings, bracelets and any other metal objects, use tools with insulated handles.

- Do not lay tools or metal parts on top of batteries.

Product Safety

w

The UPS connection instructions and operation described in the manual must be followed in the indicated order.

w

A protection circuit breaker must be installed upstream and be easily accessible. The system can be disconnected from the AC

power source by opening this circuit breaker.

w

Check that the indications on the rating plate correspond to your AC powered system and to the actual electrical consumption of

all the equipment to be connected to the system.

w

The socket-outlet shall be installed near the equipment and shall be easily accessible.

w

Never install the system near liquids or in an excessively damp environment.

w

Never let a foreign body penetrate inside the system.

w

Never block the ventilation grates of the system.

w

Never expose the system to direct sunlight or source of heat.

w

If the system must be stored prior to installation, storage must be in a dry place.

w

The admissible storage temperature range is -20ºC to +40ºC (-4

°F to 104°F).

w

The maximum operating temperature without power derating is 40

°C (104°F).

Special Precautions

w

All handling operations will require at least two people (unpacking, installation in rack system).

w

Before and after the installation, if the UPS remains de-energized for a long period, the UPS must be energized for a period of

24 hours, at least once every 6 months (for a normal storage temperature less than 25°C (77

°F)

). This charges the battery, thus

avoiding possible irreversible damage.

w

During the replacement of the Battery Module, it is imperative to use the same type and number of element as the original Battery

Module provided with the UPS to maintain an identical level of performance and safety. In case of doubt, don’t hesitate to contact

your EATON representative.

Environment

w

This product has been designed to respect the environment:

It does not contain any Chlorofluorocarbon (CFC) or Hydrochlorofluorocarbon (HCFC).

w

UPS recycling at the end of service life:

EATON undertakes to recycle, by certified companies and in compliance with all applicable regulations, all UPS products

recovered at the end of their service life (contact your EATON branch office).

w

Packing: UPS packing materials must be recycled in compliance with all applicable regulations.

WARNING: This product contains lead-acid batteries. Lead is a dangerous substance for the environment if it is not

properly recycled by specialized companies.

Federal Communication Commission (FCC) statement

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense

Symbol Usage

Important instructions that must always be followed

Information, advice, help

Visual indication

Action

Audible signal

LED off

LED on

86-86700-00EN A02 - Page 7

1. Presentation

1.1 Standard Positions

Tower Position

Rack Position

Weights in kg / lbs

EX 700 12.5 / 27.55

EX 1000 15 / 33

EX 1000 RT 2U 18 / 39.68

EX 1500 18 / 39.68

EX 1500 RT 2U 20.5 / 45.2

EX EXB 1000/1500 21 / 46.3

EX EXB 1000/1500

RT 2U

24.5 / 54

Dimensions (H x W x D) in mm / inches

EX 700

242 x 158 x 400 /

9.52 x 6.22 x 15.74

EX 1000

242 x 158 x 400 /

9.52 x 6.22 x 15.74

EX 1000 RT 2U

438 x 86.5 x 480 /

17.24 x 3.4 x 18.9

EX 1500

242 x 158 x 450 /

9.52 x 6.22 x 17.71

EX 1500 RT 2U

438 x 86.5 x 480 /

17.24 x 3.4 x 18.9

EX EXB 1000/1500

242 x 158 x 400 /

9.52 x 6.22 x 15.74

EX EXB 1000/1500

RT 2U

440 x 86.5 x 480 /

17.32 x 3.4 x 18.9

Part Numbers

EX 700 86700

EX1000 86701

EX 1000 RT 2U 86702

EX 1500 86703

EX 1500 RT 2U 86704

EX EXB 1000/1500 86705

EX EXB 1000/1500 RT 2U 86706

86-86700-00EN A02 - Page 8

1.2 Rear Panels

EX 700 / 1000 / 1500

EX 1000 RT2U / 1500 RT2U

EX EXB 1000/1500 (optional battery module)

1. Presentation

(1) USB communication port

(2) RS232 and dry contacts communication port

(3) Connector for automatic recognition of a

battery EXB module (except on EX 700)

(4) Slot for optional communication card

(5) Connector for remote ON/OFF and RPO

(Remote Power Off) control

(6) Connector for battery EXB module, except on

EX 700

tion of equipment

(8) Group of outlets for connection of equipment

(9) Input power plug for connection to AC-power

source

(10) LED (SWF) indicating distribution system

phase/neutral reversal

5

8

4

6

1

2

9

3

7

10

(11) Connectors for battery modules (to the UPS or

to the other battery modules)

(12) Connectors for automatic recognition of

battery modules

11

12

120 Volts

1 2 5 310 6 4 8

7

9

86-86700-00EN A02 - Page 9

EX EXB 1000/1500 RT2U (optional battery module)

11

12

1.3 Control Panel

(20) Load protected LED

(21) Downgraded operation LED

(22) Load not protected LED

(23) Alphanumeric display

(24) Escape (cancel) button

(25) Scroll button

(26) Enter (confirm) button

(27) ON/OFF button for UPS and outlets

1. Presentation

86-86700-00EN A02 - Page 10

2. Installation

2.1 Unpacking and Contents Check

(30) EX 700, 1000, 1500

(31) EX 1000 RT2U, 1500 RT2U

(33) RS232 communication cable

(34) USB communication cable

(36) Solution-Pac CD-ROM and documentation element

supplied depending on the version or option

(37) Mounting kit for 19-inch bays

(38) 2 supports for the upright position (RT model only)

(41) NMC communication card (optional)

i

Packing materials must be disposed of in compliance with all local regulations concerning waste. Recycling

symbols are printed on the packing materials to facilitate sorting.

86-86700-00EN A02 - Page 11

2.2 Installation of the RT Model in Tower Position

2.3 Installation of the RT Model in a Rack

It is advised to install the battery EXB module(s) at the lowest position in the rack, then install the UPS above.

Follow steps 1 to 4 for module mounting on the rails.

i

The rails and necessary hardware (37) are supplied by EATON.

2. Installation

86-86700-00EN A02 - Page 12

2.4 Communication Ports

Connection of RS232 or USB communication port (optional)

The RS232 and USB communication ports cannot operate simultaneously.

Tower model

RT model

86-86700-00EN A02 - Page 13

1. Connect the RS232 (33) or USB (34) commu-

nication cable to the serial or USB port on the

computer equipment.

2. Connect the other end of the communication

cable (33) or (34) to the USB (1) or RS232 (2)

communication port on the UPS.

The UPS can now communicate with EATON

power management software.

2. Installation

Installation of optional communication cards (optional)

Tower model RT model

It is not necessary to shutdown the UPS before

installing a communication card.

(4): Slot, with restricted access, for the communications-

card.

1. Remove the card slot cover (4) secured by screws.

2. Insert the communication card in the slot.

3. Put the card slot cover back in place using the

screws.

2.5 Connection to the Communication Port by Contact

n.o. n.o. n.o.

w Pin 2, 3, 5 and 6: not used,

w Pin 1: operation on automatic by-pass,

w Pin 4: user common,

w Pin 7: low battery,

w Pin 8: load protected,

w Pin 9: operation on battery.

n.o.: contact normally open.

When the status is active, the contact between the common (Pin 4) and the relevant information pin is closed.

Contact characteristics (optocoupler)

w Voltage: 48Vdc max

w Current: 25mA max per contact

w Power: 1.2W

2. Installation

86-86700-00EN A02 - Page 14

2.6 Connections with a FlexPDU (Power Distribution Unit) module (optional)

7

45 46 48

8 9

1. Connect the UPS socket (9) to the AC-power

source using the power cable from the equip-

ments to be protected.

2. Connect the input socket on the FlexPDU

module (48) to the UPS outlet (7) or (8). The

cable and the connectors are marked in red.

3. Connect the equipment to the outlets (45)

and (46) on the FlexPDU module. These

outlets differ, depending on the version of the

FlexPDU module.

2.7 UPS Connection

i

Check that the indications on the rear panel of the silkscreen of the UPS correspond to the AC-power source and the

true electrical source of the required load.

Tower model

1. Connect the input plug (9) to the AC power

source using the power cable from the equip-

ments to be protected.

2. Connect the loads to the UPS.

It is preferable to connect the priority loads to the

outlets marked (8) and the non-priority loads to

the outlets marked (7) that can be programmed in

pairs (1 and 2). To program the outlets, the EATON

communications software is required.

RT model

i

Note. The UPS charges the battery as soon as it is connected to the AC-power source, even if button (27) is not pressed.

Once the UPS is connected to the AC-power source, eight hours of charging are required before the battery can supply

the rated backup time.

86-86700-00EN A02 - Page 15

2. Installation

(This page left blank intentionally)

86-86700-00EN A02 - Page 16

3. Operation

3.1 Start-Up and Normal Operation

i

For the initial start, AC power must be present to detect any wiring errors. Subsequently, the UPS can start even

if AC power is not present.

UPS personalization

If UPS personalization is desired, it is advised to enter the personalization mode at this time. This mode may be

entered using the buttons on the control panel or the Personal Solution-Pac software (Windows) included on the

Solution-Pac CD-ROM provided by EATON.

3.2 Operation on Battery Power

w The connected devices continue to be supplied by

the UPS when AC power is no longer available.

The necessary energy is provided by the battery.

w LEDs (20) and (21) go ON.

w The audio alarm beeps every ten seconds.

The connected devices are supplied by the battery. The

display indicates the remaining backup time.

w LEDs (20) and (21) go ON.

w The audio alarm beeps every three seconds.

The remaining battery power is low. Shut down all

applications on the connected equipment because

automatic UPS shutdown is imminent.

Transfer to battery power

Low-battery warning

Press button (27) for approximately 1 second.

The connected devices are protected by the UPS.

w LED (20) is ON. If LED (22) is ON, a fault has

occurred (see the «Troubleshooting» section).

w During normal operation, the scroll button (25)

may be used to read UPS measurements (AC

input voltage, operating mode, battery capacity

and UPS serial number)

86-86700-00EN A02 - Page 17

End of battery backup time

w All the LEDs go OFF.

w The audio alarms stops.

The UPS is completely shut down.

3.3 Return of AC Power

Following an outage, the UPS restarts automatically when AC power returns (unless the restart function was

disabled via UPS personalization) and the load is again supplied.

3.4 UPS Shutdown

3.5 Using the UPS Remote Control Functions

EX has the choice of two remote control options.

w RPO: Remote Power Off allows a remote contact to be used to disconnect all the equipment connected to

the UPS from the power supply. Restarting the UPS requires manual intervention.

w ROO: Remote ON/OFF allows remote action of button (27). These functions are obtained by opening a

contact connected between the appropriate pins of connector (5) on the rear panel of the UPS (see dia-

gram on following page).

RT model

Tower model

Press button (27) for approximately 1 second.

The devices connected to the UPS are no longer

supplied.

86-86700-00EN A02 - Page 18

3. Operation

La page charge ...

Eaton Pulsar EX 1500 Installation and User Manual

Eaton Pulsar EX 1500 Installation and User Manual

dans d''autres langues

Documents connexes

Autres documents