Greenlee CM-450 Digital Clamp-on Meter Manuel utilisateur

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and

safety information in this manual before operating or

servicing this tool.

Lea y entienda todas las instrucciones y la

información sobre seguridad que aparecen en este

manual, antes de manejar estas herramientas o darles

mantenimiento.

Lire attentivement et bien comprendre toutes les

instructions et les informations sur la sécurité de ce

manuel avant d’utiliser ou de procéder à l’entretien de

cet outil.

CM-450

Digital

Clamp-on

Meter

Medidor digital

con pinza

Contrôleur

numérique

à pince

CM-450

TRUE RMS

2

Description

The Greenlee CM-450 Digital Clamp-on Meter is a hand-held testing device

capable of measuring up to 600 amps of alternating current, in addition to

measuring AC or DC voltage, frequency, and resistance. It also checks diodes and

veriﬁes continuity. The CM-450 is a true RMS-reading meter.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment.

This instruction manual and any markings on the tool provide information for

avoiding hazards and unsafe practices related to the use of this tool. Observe all

of the safety information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the safe

operation and maintenance procedures for the Greenlee CM-450 Digital Clamp-on

Meter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge at

www.greenlee.com.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

All speciﬁcations are nominal and may change as design improvements occur.

Greenlee Tools, Inc. shall not be liable for damages resulting from misapplication or misuse

of its products.

® Registered: The color green for electrical test instruments is a registered trademark of

Greenlee Tools, Inc.

KEEP THIS MANUAL

Lifetime Limited Warranty

Greenlee Tools, Inc. warrants to the original purchaser of these goods for use

that these products will be free from defects in workmanship and material for

their useful life, excepting normal wear and abuse. This warranty is subject

to the same terms and conditions contained in Greenlee Tools, Inc.’s standard

one-year limited warranty.

For all Test Instrument repairs, contact Customer Service at 800-435-0786

and request a Return Authorization.

For items not covered under warranty (such as items dropped, abused, etc.), a

repair cost quote is available upon request.

Note: Prior to returning any test instrument, please check replaceable

batteries or make sure the battery is at full charge.

3

CM-450

SAFETY ALERT SYMBOL

This symbol is used to call your attention to hazards or unsafe practices

which could result in an injury or property damage. The signal word, deﬁned

below, indicates the severity of the hazard. The message after the signal

word provides information for preventing or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result in severe injury or

death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or

property damage.

Read and understand this material before operating or

servicing this equipment. Failure to understand how to

safely operate this tool could result in an accident causing

serious injury or death.

Electric shock hazard:

Contact with live circuits could result in severe injury or

death.

Important Safety Information

4

Important Safety Information

Electric shock and ﬁre hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Only use the test leads provided with the equipment or UL Listed Probe

Assembly with same rating or better.

• Inspect the test leads or accessory before use. They must be clean and dry,

and the insulation must be in good condition. Do not use the test lead if the

contrasting inner layer of insulation is visible.

• Use this unit for the manufacturer’s intended purpose only, as described in

this manual. Any other use can impair the protection provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not operate with the case open.

• Before opening the case, remove the test leads (or jaw) from the circuit and

shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Using this unit near equipment that generates electromagnetic interference

can result in unstable or inaccurate readings.

• Unless measuring voltage or current, shut off and lock out power. Make sure

that all capacitors are discharged. Voltage must not be present.

Failure to observe these warnings could result in severe injury or death.

5

CM-450

Important Safety Information

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity. Refer to

“Speciﬁcations.”

Failure to observe these precautions may result in injury and can damage the

unit.

Electric shock hazard:

Do not change the measurement function while the test leads are connected to

a component or circuit.

Failure to observe this precaution may result in injury and can damage the unit.

Statement of Conformity

Greenlee Tools, Inc. is certiﬁed in accordance with ISO 9001:2008 for our Quality

Management Systems.

The instrument enclosed has been checked and/or calibrated using equipment

that is traceable to the National Institute for Standards and Technology (NIST).

6

Identiﬁcation

1. Jaw

2. Position error marks

3. Jaw center marks

4. Lever

5. Hold button

6. Relative measurement button

7. Display

8. Select button

9. Frequency button

10. Selector switch

11. Negative, common (COM), or ground input

terminal

12. Volts or resistance (VΩ) input terminal

Display Icons

13. Auto ranging is enabled.

14.

Diode test

15. Continuity mode

16. Hold function is enabled.

17. Low battery indicator

18. ∆ Relative measurement is enabled.

19. M Mega (10

6

)

20. Ω Ohms

21. Hz Hertz

22. k kilo (10

3

)

23. A Amps

24. V Volts

25. m milli (10

-3

)

26. O.L. Overload indicator

27. – Negative polarity indicator

28.

AC measurement is selected.

29.

DC measurement is selected.

Symbols on the Unit

Warning—Read the instruction manual

Application around or removal from hazardous live conductors

ispermitted.

Double insulation

Note: Unidentiﬁed icons are

not used on this model.

12

9

6

5

3

2

11

10

8

7

1

4

19

18

21

20

23

29

28

27

13 1514 16 17

242526

22

7

CM-450

Using the Features

Selector Switch

• Slide switch to desired mode of operation:

AC voltage

DC voltage

AC current

ohms/continuity/diode

• Return switch to OFF position when not in use.

Select Button (SELECT)

• Momentarily press to select resistance, continuity, or diode test when the

Selector switch is set to .

Frequency Button (Hz)

• Press to measure frequency.

Note: The sensitivity of the frequency measurement function varies with the

measurement range. To automatically select a sensitivity level, measure the

voltage level ﬁrst, and then press Hz. Pressing Hz before making a measurement

may give higher sensitivity. Reading may be zero when sensitivity is too low.

Electrical noise may cause unstable readings.

Hold Button (HOLD )

• Press momentarily to hold the present value on the display. will appear on

the display.

• Press again to return to normal mode.

Relative Measurement Button (∆)

This feature ﬁnds the difference between two measurements.

• While taking a measurement, press ∆ to set the display to zero. ∆ will appear

on the display.

• Take the second measurement. The value on the display will be the difference

between the two measurements.

• Press again to exit this mode.

Auto Power Off

To extend battery life, the meter will shut itself off after approximately 30 minutes

of inactivity. To restore power, press any button.

8

AC Measurement

AC measurements are usually displayed as RMS (root mean square) values. The

RMS value is equal to the value of a DC waveform, which would deliver the same

power if it replaced the time-varying waveform. Two AC measurement methods

are average-responding RMS calibrated and true RMS-reading.

The average-responding RMS calibrated method takes the average value of the

input signal after full wave rectiﬁcation, multiplies it by 1.11, and displays the

result. This method is accurate if the input signal is a pure sine wave.

The true RMS-reading method uses internal circuitry to read the true RMS value.

This method is accurate, within the speciﬁed crest factor limitations, whether the

input signal is a pure sine wave, square wave, triangle wave, half wave, or signal

with harmonics. The ability to read true RMS provides much more measurement

versatility. The Greenlee CM-450 is a true RMS meter.

The Waveforms and Crest Factors table shows some typical AC signals and their

RMS values.

Waveforms and Crest Factors

Waveform

RMS Value 100 100 100 100

Average

Value

90 100 87 64

Crest Factor*

(x)

1.414 1 1.73 2

* The crest factor is the ratio of the peak value to the RMS value; it is

represented by the Greek letter x.

9

CM-450

Operation

Electric shock hazard:

Contact with live circuits could result in severe injury or

death.

1. Set the Selector switch according to the Settings Table. Momentarily press the

SELECT button to select mode.

2. Refer to “Typical Measurements” for speciﬁc measurement instructions.

3. Test the unit on a known functioning circuit or component.

• If the unit does not function as expected on a known functioning circuit,

replace the battery.

• If the unit still does not function as expected, call Greenlee for technical

assistance at 800-435-0786.

4. Take the reading from the circuit or component to be tested.

Settings Table

To measure

this value …

Set the Selector

switch to this

symbol …

This icon

will appear

on the

display …

Connect

red lead

to …

Connect

black

lead

to …

AC Current*

(600 A max.)

and A N/A N/A

Frequency of a

current

(600 A max.)

and press Hz

Hz N/A N/A

Voltage

(600 V max.)

and V

+ COM

and V

Frequency of a

voltage signal

or

and press Hz

Hz + COM

Resistance MΩ + COM

Continuity**

and press SELECT

Ω

+ COM

Diode

and press SELECT

2 times

and V

+ COM

* AC current measurements are made using the jaw.

** Tone indicates continuity. The threshold is between 5 Ω and 120 Ω.

10

Typical Measurements

AC Amps

Clamp Around Wire

Notes:

• Clamp the jaw around

one conductor only.

• Close the jaw completely to

ensure accurate measurement.

• Center the wire in the jaw for

highest accuracy.

Clamp Around Line Splitter

Notes:

• The Greenlee 93-30 Line Splitter is divided.

One section renders amps; the other

renders amps multiplied by 10.

• Close the jaw completely to ensure accu-

rate measurement.

• Center the line splitter in the jaw for

highest accuracy.

11

CM-450

Voltage

Typical Measurements

Resistance

12

Forward Bias

Reverse Bias

Typical Measurements

Continuity

Diode Test

13

CM-450

Accuracy

Refer to “Speciﬁcations” for operating conditions and temperature coefﬁcient.

Accuracy is speciﬁed as follows: ± (a percentage of the reading + a ﬁxed amount)

at 23 °C ± 5 °C (73.4 °F ± 9 °F), 0% to 75% relative humidity.

True RMS readings: Voltage is speciﬁed from 5% to 100% of the range, and AC

current is speciﬁed from 10% to 100% of the range, unless otherwise speciﬁed.

Frequency must be within the speciﬁed bandwidth for non-sinusoidal waveforms.

Crest factors are as follows:

• Crest Factor < 1.75 at full scale

• Crest Factor < 3.5 at half scale

AC Current

Measurement Range Accuracy Frequency Range

0.40 to 40.00 A ± (1.5% + 0.08 A)

50 to 60 Hz 40.0 to 400.0 A ± (1.5% + 0.8 A)

400 to 600 A ± (1.5% + 8 A)

• Adjacent conductor inﬂuence < 0.05 A/A

• Add 2% if the conductor is beyond the position error marks.

• Multiply the ﬁxed error amount times 2 below 10% of range.

AC Voltage

Measurement

Range

Accuracy

Frequency

Range

Input

Impedance

4.000 V ± (1.5% + 0.005 V)

50 to 500 Hz

10 MΩ // 30 pF

nom.

40.00 V ± (1.5% + 0.05 V)

400.0 V ± (1.5% + 0.5 V)

600 V ± (2.0% + 5 V)

DC Voltage

Measurement Range Accuracy Input Impedance

400.0 mV ± (0.3% + 0.4 mV) 1000 MΩ*

4.000 V ± (0.5% + 0.003 V)

10 MΩ

40.00 V ± (0.5% + 0.03 V)

400.0 V ± (0.5% + 0.3 V)

600 V ± (1.0% + 4 V)

* The high impedance on this range will produce signiﬁcant non-zero readings

when the test leads are disconnected from a circuit.

14

Accuracy (con’t)

Resistance

Measurement Range Accuracy

400.0 Ω ± (0.8% + 0.8 Ω)

4.000 kΩ ± (0.6% + 0.004 kΩ)

40.00 kΩ ± (0.6% + 0.04 kΩ)

400.0 kΩ ± (0.6% + 0.4 kΩ)

4.000 MΩ ± (1.0% + 0.004 MΩ)

40.00 MΩ ± (2.0% + 0.04 MΩ)

Diode Tester

Test Current Open Circuit Voltage

0.25 mA typical 1.6 VDC maximum

Frequency

Function Sensitivity (Sine RMS) Range

400.0 mV 350 mV 10 Hz to 2 kHz

4.000 V 1 V 10 Hz to 5 kHz

40.00 V 32 V 10 Hz to 100 kHz

400.0 V 100 V 10 Hz to 10 kHz

600 V 500 V 10 Hz to 5 kHz

400.0 A 60 A 40 Hz to 400 Hz

Accuracy of Frequency Ranges

Display Range Accuracy

5.000 Hz ± (0.5% + 0.004 Hz)

50.00 Hz ± (0.5% + 0.04 Hz)

500.0 Hz ± (0.5% + 0.4 Hz)

5.000 kHz ± (0.5% + 0.004 kHz)

50.00 kHz ± (0.5% + 0.04 kHz)

500.0 kHz ± (0.5% + 0.4 kHz)

15

CM-450

Speciﬁcations

Display: 3-3/4-digit LCD (4000 maximum reading)

Sampling Rate: 3 per second

Overrange Indication: “OL” appears on the display

Maximum Conductor Diameter: 26 mm (1.02")

Measurement Category: Category III, 600 V

Temperature Coefﬁcient: 0.15 x (speciﬁed accuracy) per °C below 18 °C or above

28 °C

Operating Conditions:

At 0% ≤ 80% RH: 5 °C to 31 °C (41 °F to 86 °F)

Decreasing linearly to 50% RH at 40 °C (104 °F)

Altitude: 2000 m (6500') maximum

Indoor use only

Storage Conditions: -20 °C to 60 °C (-4 °F to 140° F), 0% to 80% relative

humidity with battery removed

Pollution Degree: 2

Battery: 3 V standard button battery (IEC-CR2032; ANSI-NEDA-54004LC)

CENELEC Directives: The instruments conform to CENELEC Low-voltage directive

2006/95/EC and Electromagnetic compatibility directive 2004/108/EC

Safety: Double insulation to IEC/UL/EN61010-1 Ed. 3.0, IEC/EN61010-2-032 Ed.

3.0, IEC/EN61010-2-033 Ed. 1.0, IEC/UL/EN61010-031 Ed. 1.1 and CAN/CSA-

C22.2 No. 61010-1-12 Ed. 3.0

All Terminals: CAT III 600 V AC/DC

Measurement Categories

These deﬁnitions were derived from the international safety standard for insula-

tion coordination as it applies to measurement, control, and laboratory equipment.

These measurement categories are explained in more detail by the International

Electrotechnical Commission; refer to either of their publications: IEC 61010-1 or

IEC 60664.

Measurement Category I: Signal level. Electronic and telecommunication equip-

ment, or parts thereof. Some examples include transient-protected electronic

circuits inside photocopiers and modems.

Measurement Category II: Local level. Appliances, portable equipment, and the

circuits they are plugged into. Some examples include light ﬁxtures, televisions,

and long branch circuits.

Measurement Category III: Distribution level. Permanently installed machines

and the circuits they are hard-wired to. Some examples include conveyor systems

and the main circuit breaker panels of a building’s electrical system.

Measurement Category IV: Primary supply level. Overhead lines and other cable

systems. Some examples include cables, meters, transformers, and other exterior

equipment owned by the power utility.

16

Maintenance

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity. Refer to

“Speciﬁcations.”

Failure to observe these precautions may result in injury and can damage the

unit.

Battery Replacement

Electric shock hazard:

• Do not operate with the case open.

• Before opening the case, remove the test leads (or jaw) from the circuit and

shut off the unit.

Failure to observe these warnings could result in severe injury or death.

1. Disconnect the unit from the circuit. Turn the unit OFF.

2. Remove the screws from the back cover.

3. Remove the back cover.

4. Replace the battery (observe polarity).

5. Replace the back cover and the screws.

Cleaning

Periodically wipe the case with a damp cloth and mild detergent; do not use

abrasives or solvents.

17

CM-450

Descripción

El Medidor digital con pinza modelo CM-450 de Greenlee es un instrumento de

veriﬁcación capaz de medir hasta 600 amperios de corriente alterna, además

de medir tensión alterna o continua, frecuencia y resistencia. Esta unidad es

de bolsillo y cabe perfectamente en la palma de la mano. También sirve para

veriﬁcar diodos y continuidad. El modelo CM-450 es un multímetro de lectura de

valores eﬁcaces reales.

Acerca de la seguridad

Es fundamental observar métodos seguros al utilizar y dar mantenimiento a las

herramientas y equipo Greenlee. Este manual de instrucciones y todas las marcas

que ostenta la herramienta le ofrecen la información necesaria para evitar riesgos

y hábitos poco seguros relacionados con su uso. Siga toda la información sobre

seguridad que se proporciona.

Propósito de este manual

Este manual de instrucciones tiene como propósito familiarizar a todo el personal

con los procedimientos de operación y mantenimiento seguros para el Medidor

digital con pinza, modelo CM-450 de Greenlee.

Manténgalo siempre al alcance de todo el personal.

Puede obtener copias adicionales de manera gratuita, previa solicitud en

www.greenlee.com.

¡No deseche ni descarte este producto!

Para información sobre reciclaje, visite www.greenlee.com.

Todas las especiﬁcaciones son nominales y pueden cambiar conforme tengan lugar mejoras

de diseño. Greenlee Tools, Inc. no se hace responsable de los daños que puedan surgir de la

mala aplicación o mal uso de sus productos.

® Registrado: El color verde para instrumentos de veriﬁcación eléctricos es una marca

registrada de Greenlee Tools, Inc.

CONSERVE ESTE MANUAL

Garantía limitada válida durante la vida útil del producto

Greenlee Tools, Inc. le garantiza al comprador original de estos bienes de uso, que los

mismos estarán libres de defectos de materiales y fabricación durante su vida útil,

excepto en el caso de que sean maltratados o hayan sufrido el deterioro normal. Esta

garantía está sujeta a los mismos términos y condiciones de la garantía estándar limitada

válida por un año, otorgada por Greenlee Tools, Inc.

Para reparaciones de todo instrumento de veriﬁcación, comuníquese con el

Departamento de Servicio al Cliente al 800-435-0786 y solicite una autorización de

devolución.

Puede obtener, previa solicitud, una cotización de precios de reparación para aquellos

artículos que no están cubiertos bajo esta garantía (los que se han dejado caer o han

sido maltratados).

Aviso: Antes de devolver un instrumento de veriﬁcación, revise si las baterías están

bajas y es necesario reemplazarlas.

18

SÍMBOLO DE ALERTA SOBRE

SEGURIDAD

Este símbolo se utiliza para indicar un riesgo o práctica poco segura que

podría ocasionar lesiones o daños materiales. Cada uno de los siguientes

términos denota la gravedad del riesgo. El mensaje que sigue a dichos

términos le indica cómo puede evitar o prevenir ese riesgo.

Peligros inmediatos que, de no evitarse, OCASIONARÁN graves lesiones o

incluso la muerte.

Peligros que, de no evitarse, PODRÍAN OCASIONAR graves lesiones o incluso

la muerte.

Peligro o prácticas peligrosas que, de no evitarse, PUEDEN OCASIONAR

lesiones o daños materiales.

Lea y entienda este documento antes de manejar

esta herramienta o darle mantenimiento. Utilizarla sin

comprender cómo manejarla de manera segura podría

ocasionar un accidente, y como resultado de éste, graves

lesiones o incluso la muerte.

Peligro de electrocución:

El contacto con circuitos activados podría ocasionar

graves lesiones o incluso la muerte.

Importante Información sobre Seguridad

19

CM-450

Importante Información sobre Seguridad

Peligro de electrocución e incendio:

• No exponga esta unidad ni a la lluvia ni a la humedad.

• No utilice esta unidad si se encuentra mojada o dañada.

• Utilice solo los conductores de prueba proporcionados con el equipo o un

conjunto de sonda con certiﬁcación UL con una caliﬁcación igual o superior.

• Revise minuciosamente los cables de prueba o el accesorio, antes de

utilizarlos. Deberán estar limpios y secos, y su forro aislante deberá hallarse

en buenas condiciones. No utilice el conductor de prueba si la capa interna

de aislamiento en contraste resulta visible.

• Utilícela únicamente para el propósito para el que ha sido diseñada por el

fabricante, tal como se describe en este manual. Cualquier otro uso puede

menoscabar la protección proporcionada por la unidad.

De no observarse estas advertencias podrían sufrirse lesiones graves o incluso

la muerte.

Peligro de electrocución:

• No haga funcionar esta unidad con la caja abierta.

• Antes de abrir la caja, retire del circuito los cables de prueba (o la pinza), y

apague la unidad.

De no observarse estas advertencias podrían sufrirse lesiones graves o incluso

la muerte.

Peligro de electrocución:

• Al utilizar esta unidad cerca de equipo que genere interferencia

electromagnética quizá se obtenga una lectura inexacta e inestable.

• A menos que vaya a medir tensión o corriente, apague y bloquee la energía.

Asegúrese que todos los condensadores estén totalmente sin carga. No debe

haber tensión alguna.

De no observarse estas advertencias podrían sufrirse lesiones graves o incluso

la muerte.

20

Importante Información sobre Seguridad

Peligro de electrocución:

• No intente reparar esta unidad, ya que contiene partes que deben recibir

mantenimiento por parte de un profesional.

• No exponga la unidad a ambientes de temperatura extrema o altos niveles

de humedad. Consulte la sección “Especiﬁcaciones”.

De no observarse estas precauciones podrían sufrirse lesiones o daños a la

unidad.

Peligro de electrocución:

No cambie la función de medición mientras los cables de prueba estén

conectados a un componente o circuito.

De no observarse esta advertencia podrían sufrirse lesiones o daños a la

unidad.

Certiﬁcado de Conformidad

Greenlee Tools, Inc. cuenta con certiﬁcación conforme a ISO 9001:2008 para

nuestros Sistemas de Gerencia de Calidad.

El instrumento provisto ha sido inspeccionado y/o calibrado mediante el uso de

equipo reconocido por el Instituto Nacional de Normas y Tecnologías (National

Institute for Standards and Technology [NIST]).

La page charge ...

Greenlee CM-450 Digital Clamp-on Meter Manuel utilisateur

Ce manuel convient également à

Greenlee CM-450 Digital Clamp-on Meter Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents