Yard-Man 950 Series Le manuel du propriétaire

Marque: Yard-Man

Modèle: 950 Series

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

IMPORTANT: Read Safety Rules and Instructions Carefully

Owner’s Manual

¨SET-UP ¨OPERATION ¨MAINTENANCE

PRINTED IN CANADA OG-3105

CALLING CUSTOMER SUPPORT

• LOCATE YOUR MODEL NUMBER AND SE RIAL NUMBER which ap pears on your unit and

record the in formation in the space pro vided be low.

IM POR TANT: You must have these num bers, along with the date and proof of

purchase to re ceive war ranty or ser vice.

• If you are hav ing difficulty as sembling this prod uct or if you have any ques tions re garding the

controls, operation or main tenance of this unit, please call the Cus tomer Sup port De partment.

• Customer Sup port can be reached by di aling: 1-800-668-1238

• Please have your model num ber and se rial num ber ready when you call.

NOTE: Al though both num bers are im portant, you will be asked to en ter only your

serial num ber be fore your call can be pro cessed.

For more de tails about your unit, visit our website at www.mtdcanada.com

This is where your model num ber will be,

record model number here:

This is where your se rial num ber will be,

re cord se rial num ber here:

TABLE OF CON TENTS

CALLING CUS TOMER SUPPORT .............................................2

TABLE OF CON TENTS .....................................................2

IM POR TANT SAFE OP ER A TION PRAC TICES ....................................3

SLOPE GAUGE...........................................................6

SET-UP IN STRUC TIONS ....................................................7

CON TROLS .............................................................8

OP ER A TION.............................................................9

AD JUST MENT ..........................................................12

LU BRI CA TION ..........................................................13

MAIN TE NANCE..........................................................13

OFF SEA SON STOR AGE IN STRUC TIONS......................................17

RE PLACE MENT PARTS/PIÈCES DÉTACHÉES...................................18

WAR RANTY: ............................................................29

TROU BLE SHOOTING ....................................................30

GEN ERAL OP ER A TION

• Read, un derstand, and follow all in structions

on the machine and in the manual(s) be fore

at tempt ing to as sem ble and op er ate. Keep

this manual in a safe place for fu ture and

reg u lar ref er ence and for or der ing re place -

ment parts.

• Be fa miliar with all con trols and their proper

operation. Know how to stop the ma chine

and dis engage them quickly.

• Never al low chil dren un der 14 years old to

operate this ma chine. Children 14 years old

and over should read and un derstand the

op er a tion in struc tions and safety rules in

this manual and should be trained and su -

pervised by a par ent.

• Never al low adults to operate this ma chine

with out proper in struc tion.

• To help avoid blade con tact or a thrown ob -

ject in jury, keep bystanders, helpers,

children and pets at least 75 feet from the

machine while it is in op eration. Stop ma-

chine if anyone en ters the area.

• Thoroughly in spect the area where the

equipment is to be used. Re move all stones,

sticks, wire, bones, toys and other for eign

objects which could be trip ped over or

picked up and thrown by the blade. Thrown

objects can cause se rious per sonal in jury.

• Plan your mow ing pat tern to avoid dis -

charge of ma terial to ward roads, side walks,

bystanders and the like. Also, avoid dis -

charging ma terial against a wall or

obstruction which may cause dis charged

ma te rial to ric o chet back to ward the op er a -

tor.

• Always wear safety glasses or safety gog -

gles dur ing op er a tion and while per form ing

an ad justment or re pair to pro tect your eyes.

Thrown ob jects which ric ochet can cause

serious in jury to the eyes.

• Wear sturdy, rough-soled work shoes and

close-fitting slacks and shirts. Shirts and

pants that cover the arms and legs and

steel-toed shoes are rec ommended. Never

operate this ma chine in bare feet, san dals,

slippery or light weight (e.g. can vas) shoes.

• Many in juries oc cur as a re sult of the mower

being pulled over the foot dur ing a fall

caused by slip ping or trip ping. Do not hold

on to the mower if you are fall ing; re lease

the han dle im me di ately.

• Never pull the mower back to ward you while

you are walking. If you must back the

mower away from a wall or ob struction first

look down and be hind to avoid trip ping and

then follow these steps:

a) Step back from the mower to fully ex tend

your arms.

b) Be sure you are well bal anced with sure

foot ing.

c) Pull the mower back slowly, no more than

half way to ward you.

d) Repeat these steps as needed.

• Do not op erate the mower while un der the

influence of alcohol or drugs.

• Do not put hands or feet near ro tating parts

or un der the cut ting deck. Con tact with the

blade can am putate hands and feet.

• A miss ing or dam aged dis charge cover can

cause blade contact or thrown object in ju-

ries.

• Do not en gage the self-propelled mech a-

nism on units so equipped while start ing

en gine.

• Never attempt to make a wheel or cut ting

height adjustment while the en gine is run -

ning.

• The blade control han dle is a safety de vice.

Never at tempt to bypass its op eration.

Doing so makes the safety de vice in opera-

This unit has been inspected against the man ufacturers qual ity check list. In case of a dis crep-

ancy, please call us. We will make ev ery effort to ship the part(s) by courier within one working

day of your call.

IM POR TANT SAFE OP ER A TION PRAC TICES

WARNING: This sym bol points out im portant safety in structions which, if not fol-

lowed, could en danger the per sonal safety and/or prop erty of your self and oth ers.

Read and fol low all in structions in this manual be fore attempting to op erate this

machine. Failure to comply with these in structions may result in personal in jury.

When you see this sym bol— heed its warning.

DANGER: This ma chine was built to be op erated ac cording to the rules for safe op -

eration in this man ual. As with any type of power equip ment, care lessness or er ror

on the part of the op erator can re sult in se rious in jury. This ma chine is ca pable of

amputating hands and feet and throwing ob jects. Fail ure to ob serve the following

safety in structions could re sult in se rious in jury or death.

tive and may re sult in personal in jury

through con tact with the rotating blade. The

blade con trol han dle must op erate eas ily in

both di rec tions and au to mat i cally re turn to

the dis en gaged po si tion when re leased.

• Never operate the mower in wet grass. Al -

ways be sure of your footing. A slip and fall

can cause se rious personal in jury. If you feel

you are los ing your foot ing, re lease the

blade con trol han dle im me di ately and the

blade will stop ro tating within three sec onds.

• Mow only in daylight or in good ar tificial

light. Walk, never run.

• Stop the blade when cross ing gravel drives,

walks or roads.

• If the equip ment should start to vi brate ab -

normally, stop the en gine and check

immediately for the cause. Vibration is gen-

erally a warn ing of trou ble.

• Shut the en gine off and wait un til the blade

comes to a com plete stop be fore removing

the grass catcher or un clogging the chute.

The cut ting blade continues to ro tate for a

few sec onds after the en gine is shut off.

Never place any part of the body in the

blade area un til you are sure the blade has

stopped ro tat ing.

• Never op erate mower without proper trail

shield, dis charge cover, grass catcher, blade

control han dle or other safety protective de -

vices in place and work ing. Never op erate

mower with dam aged safety de vices. Failure

to do so, can re sult in personal in jury.

• Muffler and en gine be come hot and can

cause a burn. Do not touch.

• Only use parts and ac cessories made for

this machine by the man ufacturer. Failure to

do so, can result in personal in jury.

• If situations occur which are not covered in

this manual, use care and good judg ment.

Con tact your cus tomer sup port de part ment.

SLOPE OP ER A TION

Slopes are a ma jor fac tor re lated to slip and

fall ac cidents which can re sult in se vere in -

jury. Op eration on slopes re quires ex tra

caution. If you feel un easy on a slope, do

not mow it. For your safety, use the slope

gauge in cluded as part of this man ual to

measure slopes be fore op erating this unit on

a sloped or hilly area. If the slope is greater

than 15 de grees, do not mow it.

DO:

• Mow across the face of slopes; never up

and down. Ex ercise ex treme cau tion when

changing di rection on slopes. Watch for

holes, ruts, bumps, rocks, or other hid den

objects which can cause you to slip or trip.

Tall grass can hide ob stacles. Al ways be

sure of your foot ing. A slip and fall can

cause se rious personal in jury. If you feel you

are losing your balance, re lease the blade

con trol han dle im me di ately, and the blade

will stop ro tating within 3 sec onds.

DO NOT:

• Do not mow near drop-offs, ditches or em-

bankments, you could lose your foot ing or

bal ance.

• Do not mow slopes greater than 15 de grees

as shown on the slope gauge.

• Do not mow on wet grass. Un stable foot ing

could cause slip ping.

CHILDREN

• Tragic ac cidents can oc cur if the op erator is

not alert to the presence of chil dren. Children

are of ten at tracted to the mower and the

mowing ac tivity. They do not un derstand the

dangers. Never as sume that chil dren will re -

main where you last saw them.

a) Keep chil dren out of the mow ing area

and un der the watch ful care of a re spon-

sible adult other than the operator.

b) Be alert and turn mower off if a child en-

ters the area.

c) Before and while mov ing back wards, look

behind and down for small chil dren.

d) Use ex treme care when ap proaching

blind cor ners, door ways, shrubs, trees, or

other ob jects that may obscure your vi -

sion of a child who may run into the

mower.

e) Keep chil dren away from hot or run ning

engines. They can suf fer burns from a hot

muf fler.

• Never al low chil dren un der 14 years old to

operate a power mower. Children 14 years

old and over should read and un derstand

the operation in structions and safety rules in

this manual and should be trained and su -

pervised by a par ent.

SERVICE SAFE HAN DLING OF GAS OLINE:

• To avoid per sonal in jury or prop erty dam age

use ex treme care in handling gasoline. Gas-

oline is ex tremely flammable and the va pors

are ex plo sive. Se ri ous per sonal in jury can

occur when gasoline is spilled on yourself or

your clothes which can ig nite. Wash your

skin and change clothes im mediately.

a) Use only an ap proved gas oline con tainer.

b) Never fill containers in side a ve hicle or on

a truck or trailer bed with a plas tic liner.

Always place containers on the ground

away from your ve hicle be fore fill ing.

c) When prac ti cal, re move gas-pow ered

equipment from the truck or trailer and

refuel it on the ground. If this is not possi-

ble, then re fuel such equipment on a

trailer with a por table container, rather

than from a gas oline dis penser noz zle.

d) Keep the nozzle in con tact with the rim of

the fuel tank or con tainer opening at all

times un til fueling is com plete. Do not

use a noz zle lock-open de vice.

e) Ex tin guish all cig a rettes, ci gars, pipes

and other sources of ignition.

f) Never fuel machine in doors.

g) Never re move gas cap or add fuel while

the en gine is hot or run ning. Al low en -

gine to cool at least two minutes be fore

re fu el ing.

h) Never over fill fuel tank. Fill tank to no

more than ½ inch be low bot tom of filler

neck to pro vide space for fuel ex pansion.

i) Replace gas oline cap and tighten se -

curely.

j) If gas oline is spilled, wipe it off the en gine

and equip ment. Move unit to an other

area. Wait 5 min utes be fore start ing the

en gine.

k) Never store the machine or fuel container

inside where there is an open flame,

spark or pilot light as on a wa ter heater,

space heater, fur nace, clothes dryer or

other gas ap pliances.

l) To re duce fire haz ard, keep ma chine free

of grass, leaves, or other de bris build-up.

Clean up oil or fuel spill age and re move

any fuel soaked de bris.

m) Allow ma chine to cool at least 5 min utes

be fore stor ing.

GEN ERAL SER VICE:

• Never run an en gine in doors or in a poorly

ven ti lated area. En gine ex haust con tains car-

bon mon oxide, an odor less and deadly gas.

• Be fore clean ing, re pair ing, or in spect ing,

make certain the blade and all mov ing parts

have stopped. Dis connect the spark plug

wire and ground against the en gine to pre -

vent un in tended start ing.

• Check the blade and en gine mounting bolts

at fre quent intervals for proper tight ness.

Also, vi sually in spect blade for dam age

(e.g., bent, cracked, worn) Re place blade

with the orig i nal equip ment man u fac turer’s

(O.E.M.) blade only, listed in this manual.

“Use of parts which do not meet the orig inal

equip ment spec i fi ca tions may lead to im-

proper per for mance and com pro mise

safety!”

• Mower blades are sharp and can cut. Wrap

the blade(s) or wear gloves, and use ex tra

cau tion when ser vic ing them.

• Keep all nuts, bolts, and screws tight to be

sure the equipment is in safe working con di-

tion.

• Never tamper with safety de vices. Check

their proper op er a tion reg u larly.

• After strik ing a for eign ob ject, stop the en-

gine, dis connect the spark plug wire and

ground against the en gine. Thoroughly in -

spect the mower for any dam age. Re pair the

dam age be fore start ing and op er at ing the

mower.

• Grass catcher com ponents, dis charge cover,

and trail shield are sub ject to wear and

damage which could expose mov ing parts

or al low ob jects to be thrown. For safety

pro tec tion, fre quently check com po nents

and re place im me di ately with orig i nal equip-

ment manufacturer’s (O.E.M.) parts only,

listed in this man ual. “Use of parts which do

not meet the orig i nal equip ment spec i fi ca -

tions may lead to im proper per formance

and com pro mise safety!”

• Do not change the en gine governor setting

or overspeed the en gine. The governor con -

trols the max imum safe op erating speed of

the en gine.

• Maintain or re place safety and in struction la-

bels, as nec essary.

• Observe proper dis posal laws and reg ula-

tions. Im proper dis posal of flu ids and

ma te ri als can harm the en vi ron ment.

SI-102

7.23.03

51 º

.YLEFASET AR EPOTONYAMUOYEREHWSEPOLSENI MRE TEDOTEDIUGASATEEHSSIHTESU

GNIDLIUBAFORENROCA

51AGNITNE SE RPER,ENILDETTODNODLOF

EPOLS

TSOPECNEFARO

LOHDNATHGISEERTLA CI TREVAHTIWLEVELSIHTD

ELOPREWOPA

REGNAD

.)teef01yr eveteef½2yleta m ixor ppafoesira(seer ged51fosse cxeniepolsahtiwsenil cninowomtonoD

ti,epolsahcusn

orewomdni heb-klawagn it ar epofI.yru jnisu oi resesuacdnanru trevodluocrewomgn idirA

.yru jnisu oi resnign itlu ser

,pilsdluocuoydnagn itoofruoynia tniamottlu ci ffidylemer txesi

.sepolsfoecafehtssorcareven,sepolsnwoddnapus

r ewomGNIDIRet ar epO

.sepolsnwoddnapureven,sepolsfoecafehtssorcasr ewomDNI HEB-KLAWet ar epO

SLOPE GAUGE

(Keep this sheet in a safe place for fu ture reference.)

OWNER'S

MAN UAL

SAFETY LA BEL

WARNING - Your Re spon si bil ity:

Restrict the use of this power ma chine to per sons who

read, un derstand and follow the warn ings and in struc-

tions in this manual and on the ma chine.

This unit is shipped WITHOUT GASOLINE

or OIL. After assembly, service engine with

gasoline and oil as instructed in the separate

engine manual packed with your unit.

NOTE: Reference to right or left

hand side of the mower is observed

from the operating position.

HOW TO SET-UP YOUR LAWN MOWER

Re fer to Il lus tra tion Be low

• Disconnect the spark plug wire and move it

away from spark plug as instructed in the

separate en gine man ual packed with your

unit.

• Remove the car ton in serts (if any). Re move

the loose parts which are in the carton, lift

the mower from the car ton, or cut the cor -

ners of the carton and roll the mower out.

• Pull up and back on the upper han dle to

raise the han dle into the operating po sition.

See Fig ure 1. Make cer tain the lower han dle

is seated se curely into the han dle mounting

brackets. Tighten the wing nuts on each side

of the handle. See Fig ure 2.

• Remove the hairpin clips from the outer hole

in the weld pins on the handle mounting

brackets. Place the hair pin clips in the in ner

hole. See Fig ure 2.

• Place one car riage bolt (found in the hard -

ware pack in cluded with your unit) in the

upper hole of the right handle mounting

bracket from the inside outward. Se cure

with one plas tic wing nuts. Re peat pro cess

on other side. See Fig ure 2.

NOTE: Make certain the drive ca ble is

routed around the out side and above

the lower handle so it does not in terfere

with at taching the grass bag.

• The rope guide (pigs tail) is part of the grass

catcher support rod at tached to the lower

handle. See Fig ure 3. With the spark plug

wire dis con nected and grounded as in -

structed in the sep arate en gine manual,

hold the blade con trol han dle against the up -

per han dle, and pull the starter rope out of

the en gine slowly un til it ex tends past the

rope guide (pigs tail).

• Guide the starter rope around the rope guide

(pig tail) un til the rope is securely in the cen -

ter.

• Make certain all nuts and bolts are tightened

se curely.

SET-UP INSTRUCTIONS

Fig ure 1

Upper

Handle

Rope Guide

Lower Handle

Cutting Height

Adjustment Lever

Wing Nut

Shift Lever

Drive Clutch

Control

Handle Mounting

Bracket

Blade Control Handle

CONTROLS

BLADE CONTROL HANDLE

WARNING: This con trol mech anism

is a safety de vice. Never at tempt to

by pass its op er a tions.

The blade con trol han dle is located on the

upper han dle of the mower. See Fig ure 1.

The blade control han dle must be de pressed

in or der to op erate the unit. Re lease the

blade con trol han dle to stop the en gine and

blade.

WARNING: The blade will be rotat-

ing whenever the en gine is run ning.

RECOIL STARTER

The recoil starter handle is attached to the

handle. See Figure 3. Stand behind the unit

in the operating position to start the unit.

IGNITION SWITCH (Electric Start Units

Only)

The ignition switch is located on the left side

of the handle panel. It is used for starting

only. See Figure 4.

DRIVE CLUTCH CONTROL

Squeezing the drive clutch control engages

the drive system. Releasing the clutch

control disengages the drive system.

Release the clutch control to slow down

when negotiating an obstacle, making a turn

or stopping.

SHIFT LEVER

The shift lever is located on the drive clutch

control housing on the upper handle. See

Figure 1. This lever is used to select the

forward speed of the mower. When changing

your speed selection, release the drive

clutch control.

NOTE: Only move the shift le ver when

the engine is run ning. Changing the

shift le ver setting with the en gine off

can cause dam age to the mower.

CUTTING HEIGHT ADJUSTMENT LEVER

(Models: 959 & 979)

The height adjuster determines the cutting

height of the mower. The ad juster is located

above the left rear wheel. To ad just the cut-

ting height, pull the le ver out and away from

the mower and then move it for ward or back

to se lect a new cutting height. See Fig ure 5.

CUTTING HEIGHT ADJUSTMENT LEVER

(Model: 999)

The rear wheel height ad juster de ter mines

the cut ting height of the mower. The adjuster

is lo cated above the left rear wheel. To ad -

just the cut ting height, pull the le ver out and

away from the mower and then move it for -

ward or back to select a new cut ting height.

See Fig ure 5.

The front wheel cut ting height is de termined

by the selection of one of six po sitions in

each caster as sembly. See Fig ure 6.

To ad just, remove the wing nut from the axle

bolt. Slide the axle bolt and spring washer

from the as sembly and se lect a cut ting

Fig ure 2

Carriage

Bolt

Wing Nut

Upper Hole

Place the hairpin clips in the inner hole.

Weld Pin

Lower Handle

Figure 4-(Electric Start Units Only)

Ignition Key (Switch)

Fig ure 3

Rope

Guide

Recoil

Starter

Lower

Handle

Support

Rod

height. With the spring washer on the axle

bolt re insert in the square hole de sired,

through the wheel as sembly and se cure with

the wing nut pre viously re moved.

IM POR TANT: All wheels must be placed in

the same rel a tive po si tion.

NOTE: For rough or un even lawns,

move the height ad justment le ver to a

higher po sition. This will help stop

scalp ing.

CASTER LOCK

WARNING: When op er at ing mower

on hills, front wheels should be

locked in the straight ahead po si-

tion.

The cast ers can be locked in a straight

ahead po sition or can be left to swivel freely.

Lift and place the lock pins in the larger

holes for locked, straight ahead op eration,

place pins in smaller holes to al low cast ers

to ro tate freely.

OPERATION

IM POR TANT: Move the shift le ver ONLY

when the en gine is run ning. Shifting the

speeds with the en gine off can cause dam -

age to the unit. Disengage the drive clutch

control be fore changing the speed se lection.

Service the en gine with gas oline and oil as

instructed in the sep a rate en gine man ual

packed in your mower. Read in structions

care fully.

WARNING: Never fill fuel tank in-

doors, with engine run ning or un til

the en gine has been al lowed to

cool for at least two minutes af ter

run ning.

BEFORE STARTING

MODELS WITH ELEC TRIC START ONLY:

WARNING: The bat tery con tains

corrosive fluid and toxic material.

HANDLE WITH CARE. Keep away

from chil dren. Do not punc ture, dis-

as sem ble, mu ti late or in cin er ate.

Explosive gases could be vented

dur ing charg ing or dis charg ing. Use

in a well-ventilated area, away from

sources of ig nition.

• Charge bat tery for 16 hours be fore ini tial

use. DO NOT CHARGE LONGER THAN 20

HOURS.

IMPORTANT: Use only the battery

charger supplied with this mower.

To charge the battery, first re move the pro -

tective cap from the end of the bat tery pack

lead. Al ways plug charger lead into bat tery

pack lead be fore in serting bat tery charger

plug into 120 volt stan dard house hold out let.

See Fig ure 7.

Af ter charg ing, dis con nect bat tery charger

plug from household outlet first, then dis con-

nect charger lead from bat tery pack lead.

Fig ure 6

Locking Pin

Axle Bolt

and

Spring

Washer

Figure 5

Cutting Height Adjustment Lever

LOWER

HIGHER

Fig ure 7

Protective

Cap

Battery

pack

lead

WARNING: Do not re move the bat -

tery pack from the handle panel for

any rea son other than re placement.

When re placing the battery pack,

re fer to in struc tions in Main te nance

sec tion.

NEUTRAL TEST FOR ALL MODELS:

• Before each use, check for proper drive

clutch op er a tion by per form ing the fol low ing

before start ing the engine:

With the drive clutch con trol re leased, push

mower for ward. It should move freely.

If it does not and the rear wheels tend to

lock up, the clutch may not be re leasing

completely. Do not start the en gine un til cor-

rections have been made. Check the con trol

cable for se vere bend, kinks and bind ing, or

grass build-up in the pul ley groove. Refer to

the "Ad justment" section for any ad ditional

in for ma tion.

TO START ENGINE AND EN GAGE BLADE

WARNING: When starting the unit

for the first time, place mower in

first speed (slow) po sition. Face the

mower against a solid ob ject such

as a wall, fence, etc. Start the unit,

and if it shows any signs of mo tion

with the drive clutch control disen-

gaged, shut the en gine off im medi-

ately. Make cer tain the drive clutch

control is ad justed so the drive belt

is as loose as pos sible. Re fer to the

Ad just ment Sec tion.

• Attach spark plug wire to spark plug. If unit

is equipped with a rub ber boot over the end

of the spark plug wire, make cer tain the

metal loop on the end of the spark plug wire

(inside the rub ber boot) is fas tened se curely

over the metal tip on the spark plug. See

Fig ure 8.

• If your unit is equipped with a primer, prime

engine as in structed in the sep a rate en gine

manual packed with your unit.

• If your unit is equipped with a two speed

control on the en gine re fer to the sep arate

engine man ual packed with your unit.

• Standing be hind the unit, de press the blade

control han dle and hold it against the up per

handle as shown in Fig ure 9.

ELECTRIC START MODELS ONLY:

• Turn the ig ni tion key to the right to start the

engine. Re lease the key af ter en gine starts.

See Fig ure 4.

NOTE: The en gine on your unit is

provided with an auxiliary re coil

starter sys tem. To start the en gine

using the auxiliary start sys tem, pro -

ceed as follows for recoil start

mod els:

RECOIL START MODELS ONLY:

• Grasp the re coil starter han dle as shown and

pull slowly un til re sistance is felt, then pull

rapidly to start en gine and avoid kickback.

Return it slowly to the rope guide bolt. See

Fig ure 9.

• To en gage the drive, squeeze the drive clutch

control han dle (see Fig ure 9) to wards the up -

per han dle. Release the drive clutch control

to slow down when ne gotiating an ob sta cle,

making a turn, or stop ping.

• The six speed shift le ver is lo cated on the

drive clutch con trol hous ing on the up per

handle. See Fig ure 9. This le ver is used to se -

lect the operating speed of the mower.

Release the drive clutch con trol when chang-

ing speeds.

WARNING: THIS CON TROL MECH A-

NISM IS A SAFETY DE VICE. NEVER

ATTEMPT TO BY PASS ITS OP ERA-

TIONS.

The blade control han dle must be de pressed

in or der to op erate the unit. Re lease the

blade con trol han dle to stop the en gine and

blade.

Figure 9-RE COIL START MODEL SHOWN

Recoil Start

Handle

Blade Control Handle

Drive

Clutch

Handle

Six Speed

Shift Lever

Fig ure 8

Metal

Loop

on Spark

Plug Wire

Rubber Boot

TO STOP ENGINE

• Release the blade con trol han dle to stop the

engine and blade.

WARNING: The blade continues to

rotate for a few seconds af ter the

engine is shut off.

• Disconnect the spark plug wire and ground it

against the en gine as in structed in the sepa-

rate en gine man ual to pre vent ac ci den tal

starting while equip ment is un attended.

USING YOUR ROTARY MOWER

Be sure that lawn is clear of stones, sticks,

wire, or other ob jects which could dam age

lawn mower or en gine. Such objects could

be ac cidentally thrown by the mower in any

di rec tion and cause se ri ous per sonal in jury to

the op er a tor and oth ers.

For the best re sults, do not cut wet grass be -

cause it tends to stick to the un derside of the

mower, pre venting proper mulching of grass

clippings. In ad dition, wet grass could cause

you to slip and fall. New grass, thick grass or

wet grass may re quire a narrower cut.

For best re sults, cut off one-third or less of

the total length of the grass. Lawn should be

cut in the fall as long as there is growth.

The mower is designed to be op erated at full

throttle to give you the best cut and do the

most ef fective job of mulching.

WARNING: If you strike a foreign

object, stop the en gine. Re move

wire from spark plug, thor oughly in -

spect the mower for any dam age,

and re pair the dam age be fore re -

start ing and op er at ing the mower.

Ex ten sive vi bra tion of the mower

dur ing op er a tion is an in di ca tion of

damage. The unit should be

promptly inspected and repaired.

BAGGING GRASS CLIPPINGS

This mower can bag grass clip pings. Fol low

steps 1 through 3 to ready the mower for

bag ging.

1. Remove wing nuts holding mulch ing baf fle

(see Fig ure 10) or side dis charge chute

(see Fig ure 14) in place. Then re move

baffle or dis charge chute.

2, Re place with bag ging adapter (see Fig ure

11). Attach using wing nuts. Be sure that

inner lip of attachment goes un der the

edge of the deck.

3. Lift flap and slide bag onto adapter. See

Fig ure 12.

EMPTYING YOUR GRASS BAG

Lift grassbag from the bag ging adapter using

the lower han dle. While hold ing the lower

handle lift up the rear sec tion of the

grassbag. The bag will open and the grass

clippings will fall out. See Figure 13. When

replacing your grassbag be sure the top of

the bag rests on the wire sup port be tween

the han dles.

Figure 10

Wing Nuts

Mulching

Baffle

Fig ure 12

Flap

Bagging

Adapter

Fig ure 11

Bagging Adapter

SIDE DISCHARGE GRASS CLIPPINGS

This mower can also side dis charge grass

clippings. Fol low steps 1 and 2 to ready this

mower for side dis charge op eration.

1. Re move mulching baf fle or grass bag

adapter. See Fig ure 10.

2. Attach discharge chute with wing nuts. See

Fig ure 14.

ADJUSTMENT

CAUTION: DO NOT AT ANY TIME MAKE

ADJUSTMENTS TO LAWNMOWER WITH -

OUT FIRST STOPPING THE ENGINE AND

DISCONNECTING THE SPARK PLUG

WIRE

CAUTION: Before changing mowing

height, stop mower and disconnect

spark plug cable.

MODELS WITH SINGLE LEVER HEIGHT

ADJUSTERS:

Refer to “Controls Section” and Figure 5.

DRIVE CLUTCH CONTROL ADJUSTMENT

Use the ad justment wheel lo cated on the un -

derside of the clutch control hous ing to

tighten the drive belt if mower does not

self-propel with the drive clutch con trol en -

gaged, or if drive belt is slip ping (unit

hesitates while en gine main tains the same

speed). See Fig ure 15.

In ad dition, the adjustment wheel may also

be used to de termine the po sition in which

the drive clutch con trol is en gaged. If it is

more com fortable to have the drive engaged

with the lever fur ther away from the han dle,

tighten the drive belt.

Make certain to re test the unit for neutral as

instructed in the op eration Section. Move the

ad just ment wheel in the op po site di rec tion to

loosen the drive belt if nec essary.

SIX SPEED SHIFT CABLE ADJUSTMENT

Periodic ad justment of the six speed shift ca -

ble may be re quired due to nor mal stretch

and wear on the cable. Adjustment is

needed if all six speeds can not be ob tained.

The ad justable ca ble bracket is lo cated on

the left side of the mower, be side the en gine.

To adjust, loosen the hex nut which se cures

the ad justable ca ble bracket. See Fig ure 16.

Pull back ward on the bracket (toward the

rear of the mower). Retighten the hex nut.

Test the speeds on the mower (en gine must

be run ning).

CARBURETOR ADJUSTMENT

Refer to the sep arate en gine man ual packed

with your mower for car buretor ad justment

in for ma tion.

Figure 14

Side

Discharge

Chute

Wing Nut

Figure 13

Figure 15

nesooL

nethgiT

BOT TOM

VIEW

LUBRICATION

CAUTION: DISCONNECT SPARK

PLUG WIRE BEFORE SERVICING.

WHEELS - If your mower is equipped with

ball bearing wheels, lu bricate at least once a

season with a light oil, all other types re quire

no lu brication. However, if the wheels are re-

moved for any rea son, lu bricate the sur face

of the axle bolt and the in ner sur face of the

wheel with light au tomotive oil.

ENGINE - Follow en gine man ual for lu brication

in struc tions.

BLADE CON TROL - Lu bricate the pivot points

on the blade control han dle and the brake ca ble

at least once a sea son with light oil. The blade

control must op erate freely in both di rections.

TRANS MIS SION - The trans mission is

pre-lubricated and sealed at the fac tory. It

does not re quire checking. If dis assembled

for any reason, fill with 2 ounces of Alvania

grease, part num ber 737-0168.

MAINTENANCE

For best re sults your blade should be sharp.

The blade may be resharpened by re moving

it and ei ther grinding or filing the cutting

edge keep ing as close to the orig inal bevel

as pos si ble.

Improper blade balance will re sult in ex ces-

sive vi bra tion caus ing even tual dam age to

the en gine and mower. Be sure to carefully

bal ance blade af ter sharp en ing.

After pro longed use, es pecially in sandy soil

conditions, the blade will be come worn and

lose some of the orig inal shape. Cut ting ef fi-

ciency will be re duced and the blade should

be re placed. Re place with an ap proved fac tory

re place ment blade only. Pos si ble dam age re-

sulting from blade un balance con dition is not

the re spon si bil ity of the man u fac turer.

ENGINE

Refer to the sep arate en gine man ual for en -

gine main te nance in struc tions.

Main tain en gine oil as in structed in the sep a-

rate en gine man ual packed with your unit.

Read and follow in structions carefully.

Un der nor mal con di tions ser vice air cleaner

as in structed in the separate en gine man ual

packed with your unit. Clean ev ery few

hours un der ex tremely dusty conditions.

Poor en

gine performance and flooding usu-

ally in dicates that the air cleaner should be

ser viced.

The spark plug should be cleaned and the

gap re set once a sea son. Spark plug re place-

ment is recommended at the start of each

mowing sea son; check en gine man ual for cor-

rect plug type and gap spec ifications.

NOTE: This spark ignition sys tem meets

all re quire ments of the Ca na dian In ter fer -

ence-Causing Equip ment Reg u la tions.

Clean the en gine reg ularly with a cloth or

brush. Keep the cooling system (blower hous-

ing area) clean to per mit proper air circulation

which is es sential to en gine per formance and

life. Be certain to re move all grass, dirt and

com bus ti ble de bris from muf fler area.

DECK

The un derside of the mower deck should be

cleaned after each use to prevent a buildup of

grass clippings, leaves, dirt or other mat ter. If

this de bris is al lowed to ac cumulate, it will in -

vite rust and cor rosion, and may pre vent

proper mulching.

The deck may be cleaned by tilt ing the mower

and scraping clean with a suit able tool (make

certain the spark plug wire is dis connected).

CUTTING BLADE

WARNING: Be sure to dis connect

and ground the spark plug wire and

re move ig ni tion key be fore work ing

on the cut ting blade to prevent ac ci-

den tal en gine start ing. Pro tect hands

by using heavy gloves or a rag to

grasp the cut ting blade.

Tip mower as spec ified in separate en gine

manual. If it is not spec ified tip with car buretor

up.

Fig ure 16

Hex Nut

Adjustable

Cable Bracket

Six Speed

Cable

Remove the bolt and blade sup port which

holds the blade and adapter to the en gine

crankshaft. Re move the blade and adapter

from the crank shaft.

WARNING: Pe ri odically in spect the

blade adapter for cracks, es pecially if

you strike a for eign ob ject. Re place

when nec es sary.

For best re sults your blade should be sharp.

The blade may be resharpened by re moving it

and ei ther grinding or fil ing the cutting edge

keeping as close to the orig inal bevel as pos -

sible. It is ex tremely im portant that each

cutting edge receives an equal amount of

grinding to prevent an un balanced blade. Im -

proper blade bal ance will re sult in ex cessive

vibration causing even tual damage to the en -

gine and mower. Be sure to care fully bal ance

blade af ter sharp ening. The blade can be

tested for bal ance by bal ancing it on a round

shaft screw driver. Re move metal from the

heavy side un til it bal ances evenly.

Before re assembling the blade and the blade

adapter to the unit, lu bricate the en gine crank-

shaft and the in ner sur face of the blade

adapter with light oil. In stall the blade adapter

on the crankshaft with the “star” away from the

engine. Re fer to Fig ure 18. Place the blade

with the side marked bot tom (or with part

number) fac ing away from the adapter. Align

the blade bell sup port over the blade with the

tabs in the holes of the blade and in sert the

hex bolt. Tighten the hex bolt to the torque

listed be low:

Blade Mounting Torque

Center Bolt 450 in. lb. min., 600 in.lb. max.

To in sure safe op eration of your unit, ALL

nuts and bolts must be checked pe riodically

for cor rect tight ness.

CAUTION: Cutting grass in sandy

soil conditions causes abrasive

wear to the blade.

After pro longed use, es pecially in sandy soil

conditions, the blade will be come worn and

lose some of the orig

inal shape. Cut ting ef fi-

ciently will be re duced and the blade should be

replaced. Re place with an ap proved fac tory re -

placement blade only. Pos sible dam age

re sult ing from blade un bal ance con di tion is not

the re spon si bil ity of the man u fac turer.

BELT REMOVAL AND REPLACEMENT

1. Dis connect the spark plug wire and

ground it against the engine.

2. Drain the fuel tank or place a piece of plas -

tic be neath the cap to prevent gasoline

leak age.

3. Tip the mower on its side. Block se curely.

4. Re move the blade and blade adapter as

de scribed previously.

5. Move rear height adjuster to the highest

po si tion. See Fig ure 21.

6. Using a 3/8" socket re move three hex

screws holding the baffle to the deck. See

Fig ure 19.

7. Pivot baf fle to wards the rear of the mower.

See Fig ure 20.

8. Re move the hex bolt holding the transmis-

sion to the mower hous ing. See Figure

21.

Figure 18

Blade Adapter

Blade

Hex Bolt

Blade Bell

Support

Figure 19

Hex

Screw

Hex

Screw

Hex

Screw

Figure 20

Baffle

9. Tilt the trans mission for ward and loosen

the idler pul ley bolt and locknut ½ turn

using two 7/16" wrenches.

10. Using a pair of pli ers, pull back and ro tate

belt keeper bracket from the slot on idler

pul ley.

11. Slide the belt out from be tween the belt

keeper bracket and the idler pul ley. See

Fig ure 22.

12. Squeeze the belt to gether and push belt

forward. Press the con trol arm in ward to -

wards the deck and re move the six speed

cable from the slot. See Fig ure 23.

13. Pivot the con trol arm down away from the

pulley and belt. See Fig ure 24.

14. Lift off the lower pul ley as sembly and re -

move the old belt from around the

crankshaft. See Figure 25.

15. Place the new belt over the trans mission

pulley. Start the belt in pul ley groove and

rotate pulley until belt is seated in trans-

mission pul ley. See Fig ure 25.

16. Place belt be tween idler pul ley and the

belt keeper bracket.

Mower is shown tipped on en gine for clarity.

Remember, only tip mower back on its han -

dle with the spark plug facing up.

Figure 22

Transmission

Pulley

Belt

Idler Pulley

Belt Keeper

Bracket

Idler Pulley

Bracket

Bolt and

Locknut

Figure 23

Belt

Control

Arm

Six-Speed

Cable Slot

Figure 21

Baffle

Hex

Bolt

Rear Wheels Adjustment Lever

Figure 24

Control

Arm

Six-Speed

Cable Slot

Figure 25

Crankshaft

Belt

Lower Pulley

Half

17. Using pli ers, rotate the belt keeper bracket

so that it snaps into slot on the idler

bracket.

18. Tighten the idler pul ley bolt and locknut ½

turn us ing two 7/16" wrenches. See Fig ure

22.

19. Place belt be tween the two pul ley halves on

the crank shaft. Make sure to route the belt

inside the belt guard pin. See Fig ure 26.

IM POR TANT: For proper as sembly, it

is es sential to keep the as sembly

positioned as shown in Figure 26.

20. Pinch belt to gether so that it is not in the pul-

ley groove, and the lower pul ley can be

pushed to wards the en gine. See Fig ure 27.

21. Pivot the con trol arm back to its orig inal po si-

tion and re install the six-speed ca ble into the

slot.

22. Check and make sure the belt is routed in -

side the pul ley halves and the belt guard

pin. See Fig ure 28.

23. Re in stall the bolt se cur ing trans mis sion to

rear mower hous ing.

24. Pivot the baf fle back to its orig inal po sition

and se cure with three hex screws ear lier re -

moved. You will need a 3/8" socket for these

screws.

25. Lightly lu bricate the crank shaft and re install

blade and blade adapter as de scribed in the

“Cutting Blade” sec tion.

26. Tip the mower back on its wheels.

27. Make cer tain to re test the unit for neutral as

in structed in the Op er a tion Sec tion.

BATTERY PACK REPLACEMENT (Electric

start Models Only)

Remove the bat tery pack from the han dle panel

for replacement only. Do not separate the bat -

teries for any rea son. Dis pose of bat teries

prop erly.

WARNING: Bat teries con tain sul fu-

ric acid which may cause burns. Do

not short cir cuit or mu

tilate in any

way. Do not put bat teries in fire.

They may burst or release toxic ma -

te rial.

When re placing bat tery pack in han dle

panel, bat tery pack must be po sitioned with

the positive ter minal to the right hand side

and the neg ative terminal to the left hand

side of panel. See Fig ure 29. Replacing the

battery pack in correctly will cause se rious

dam age.

The pos itive lead on the wire har ness has

the smaller connector. Con nect the pos itive

Figure 26

Belt

Lower

Pulley

Half

Belt Guard

Upper Pulley

Half

Figure 27

Belt

Lower Pulley

Half

Belt Guard

Figure 28

Figure 29

Positive

terminal

Negative

terminal

Fuse Holder

lead to the pos itive side of the bat tery pack,

then con nect the neg ative side.

IN-LINE FUSE

The unit is equipped with an in-line fuse. If

unit fails to start, check the fuse in side the

battery cover by turning the end of the fuse

holder and removing from the bat tery cover.

See Fig ure 29. Re place with stan dard au to-

motive 7-1/2 amp fuse.

OFF SEASON STORAGE

INSTRUCTIONS

The fol lowing steps should be taken to pre -

pare lawn mower for stor age.

1. Clean and lubricate mower thoroughly as

de scribed in the lu bri ca tion in struc tions.

2. Re fer to en gine manual for cor rect en gine

stor age in struc tions.

3. Coat mower’s cut ting blade with chas sis

grease to pre vent rust ing.

4. Store mower in a dry, clean area.

STORAGE OF THE BATTERY

The bat tery must be stored with a full

charge. A discharge bat tery will freeze.

IMPORTANT: All batteries discharge

during storage.

Recharge battery ev ery two months and be -

fore re turning to ser vice. Re fer to charg ing

instructions on page 9.

NOTE: When stor ing any type of power

equipment in an un ventilated or metal

storage shed, care should be taken to

rust-proof the equipment. Using a light

oil or sil icone, coat the equipment, es -

pecially ca bles and all moving parts.

CAUTION: Never fold or un fold

han dle with out dis con nect ing spark

plug.

NOTE: Be careful not to bend of kink

ca bles.

NOTE: If the starter rope becomes dis -

connected from rope guide on handle,

disconnect and ground the spark plug

wire. De press the bail and pull the

starter rope out from engine slowly. Slip

the starter rope into the rope guide bolt

on han dle.

RE PLACE MENT PARTS/PIÈCES DÉTACHÉES

MODELS/MODÈLES 950 & 970

Pulley assembly

for reference only./

Poulie illustrée à

titre de référence

seulement.

Transmission and pulley for

reference only./Transmission et

poulie illustrées à titre de

référence seulement.

REF PART

NO. NO.

N° DE N° DE

RÉF PIÈCE DE SCRIP TION DE SCRIP TION

1 638-0012 Axle Ass’y 20T x 21.46" Lg. Essieu 20 dents x 21,46 po de lg.

2 682-0531 Pivot Arm Ass’y Bras du pivot

3 682-7526 Trans Axle Ass’y Essieu

4 682-7528 Chain Cover Couvercle de chaîne

5 710-0604A Hex Wash HD Scr 5/16-18 x .62 Vis taraudée 5/16-18 x 0,62

6 710-0653 Hex Wash HD Tapp Scr 1/4-20 x .38 Vis auto-taraudeuse hex. 1/4-20 x 0,38

7 710-0751 Hex Bolt 1/4-20 x .62 Boulon hexagonale 1/4-20 x 0,62

8 710-1652 Hex Wash Hd. Scr 1/4-20 x .625" Lg Vis taraudée à tête hexagonale 1/4-20 x 0,625

9 710-1315 TT Screw 3/8-16 x 1.25 Vis 3/8-16 x 10,25

10 711-0835 Clevis Pin .5" Dia. x 4.62" Lg. Axe de chape 0,5 dia x 4,62 po de lg

11 713-0453 Chain, No. 48 End less .50 x 24 links Chaîne, no. 48 End less 0,5 x 24 maillons

12 714-0474 Cot ter Pin Goupille fendue

13 720-0223 Grip Poignée

14 732-0803A Spring Le ver Levier de ressort

15 732-0832 RH Torsion Sprocket Pignon de tor sion - droite

16 736-0270 Cupped Wash. .25 ID x .88 OD x .062 Rondelle creuse. 0,25 DI x 0,88 DE x 0,062

17 736-0369 Washer, Flat .505 ID x 1.0 Rondelle plate 0,505 DI x 1,0

18 738-0529 Shoulder Nut .625 DIA. x .165 Écrou épaulée 0,625 DIA x 0,165

19 741-0324A Flange Bear ing .506 ID Roulement à bride de 0,506 DI

20 741-0522 Hex Flange Bear ing Roulement à bride hex.

21 741-0978 Hex Sleeve Bear ing .504 x .830 Lg. Roulement hex. 0,504 x 0,830 po de lg.

22 748-0318 Ratchet Wheel Roue à rochet

23 750-0151 Spacer .55 ID x .75 Bague d’espacement 0,55 DI x 0,75

24 750-0515 Sleeve .511 ID x .70 OD x .37" Lg. Manchon de 0,511 DI x 0,70 DE x 0,037

25 750-0807 Spacer .38 x .625" Lg. Entretoise 0,38 x 0,625 po de lg

26 750-1056 Shoulder Spacer .385 ID x .715" Lg. Entretoise 0,385 DI x 0,715 po de lg.

27 782-0568 Spring Bracket Support de ressort

28 710-0654A Hex Wash HD Tap Scr 3/8-16 x .88 Vis autotaraudée 3/8-16 x 0,88

31 682-3052 Handle Brkt. Ass’y RH Support du guidon - doite

32 682-3053 Handle Brkt. Ass’y LH Support du guidon - gauche

33 710-1348 Screw AB 1/4-20 Vis 1/4-20

34 725-0157 Ca ble Tie Attache câble

35 731-1901A Rear Flap 17.25" Lg. Abattant de pro tection arrière 17,25 po de lg.

36 732-0842 Rear Flap Wire Fil de abattant de protection arrière

37 10622B Spring Nylon Ressort ny lon

38 16855 Pawl Plate Clique - plaque

39 712-0414 Toplock Flat Weldnut 1/4-20 Écrou soudée plat 1/4-20

40 738-0137A Shoulder Screw .340 x .285: 1/4-20 Vis à épaulement 0,340 x 0,285, 1/4-20

41 748-0188B Pawl LH (Not Shown) Cliquet (non illustrée)

41 748-0381 Pawl RH Cliquet CD

42 710-0134 Carriage Bolt 1/4-20 x .62 Boulon ordinaire 1/4-20 x 0,62

43 710-0703 Carriage Bolt 1/4-10 x .75 Boulon ordinaire 1/4-20 x 0,75

44 712-0397 Wing Nut Écrou à oreilles

45 726-0233 Bolt Re tainer 1/4" x .50" OD Boulon de retenue 1/4" x 0,50" DE

46 731-1832 Side Chute Déflecteur

47 731-1833A Mulching Baf fle Déflecteur de déchiquetage

49 782-0046B Deck Ass’y (w/logo) Plateau de coupe (avec logo)

782-0078B Deck Ass’y (w/o logo) Plateau de coupe (sans logo)

50 618-0263A Trans mis sion Ass’y Trans-essieu

51 746-0711B SP Ca ble 51.0" Lg. Yellow Câble 51,0 po de lg jaune

52 754-0460 V-Belt 3/8 x 39.24" Lg. Courroie trapézoïdale 3/8 x 39,24 po de lg

53 812-00251 Pul ley (6 speed ac tu a tor) Poulie

54 611-0064 Axle Ass’y Essieu

55 710-1241 Hex Wash. Hd. B-Tap Scr. 1/4 x 1.0" lg Vis autotaraudeuse 1/4 x 1,0 po de lg.

56 710-1242 Torx Hd. Scr. 5/16 x .75 Vis torx 5/16 x 0,75

57 714-0104 Int. Cot ter Pin 5/16 DIA Goupille fendue 5/16 DIA.

Con tinued on next page/Suite à la page prochaine

REF PART

NO. NO.

N° DE N° DE

RÉF PIÈCE DE SCRIP TION DE SCRIP TION

58 731-1829 Front Cover- Yellow Couvercle avant - jaune

731-1834 Front Cover- Grey Couvercle avant - gris

731-1836 Front Cover- Black Couvercle avant - noir

59 736-0286 Bowed Washer Rondelle évasée

60 741-0492A Bushing Block .505 dia. Bloc de roulement

61 782-0565 Single Le ver Arm Con trol Bras de commande

63 710-0969 Screw H.L. 12-24 Vis 12-24

64 731-1828 Baf fle Protecteur

65 736-0105 Cupped Wash .400 ID x .88 OD x .06 Rondelle creuse 0,400 DI x 0,88 DE x 0,06

66 738-0102 Axle Bolt Boulon de l’essieu

67 736-0504 Wave Washer .51" ID Rondelle ondulée 0,51 DI

68 710-1257 Hex Bolt 3/8-24 x 2.5" Lg. Boulon hex. 3/8-24 x 2,5 po de lg.

69 736-0524B Bell Blade Support Support de lame

73 742-0741 Blade 21" (w/star) Lame 21 po (avec étoile)

74 748-0377C Blade Adapter (w/star) Adaptateur de lame (avec étoile)

75 631-0067 Chute As sembly (Incl. items *) Déflecteur (Comprends les *)

* 76 726-0111 Push Cap .188 Rod Chapeau à enfoncer 0,188 po

* 77 731-1713B Top Chute Déflecteur supérieur

* 78 731-1874 Chute Door Porte de goulotte

* 79 732-0819 Tor sion Spring Ressort de torsion

* 80 747-0965 Pivot Rod Tige de pivot

83 734-1978 Front Wheel Ass’y 8 x 2 Ensemble de roue avant 8 x 2,0

(Link/Blk/Ball Brg) (Link/noir/roulement à billes)

734-2008A Front Wheel Ass’y 8 x 2.125 Ensemble de roue avant 8 x 2,125

(Idle/Blk/Ball Brg) (Idle/noir/roulement à billes)

734-1979 Front Wheel Ass’y 8 x 2 (Link/Blk Ensemble de roue avant 8 x 2,0

(Link/noir/avec

Plas tic Brg) coussinet)

734-2004A Front Wheel Ass'y 8 x 2.125 (Idle/Zag Ensemble de roue avant 8 x 2,125

Ball Brg) (Idle/Zag/roulement à billes)

85 734-1981A Rear Wheel Ass’y 9 x 2.00 Ensemble de roue 9 x 2,00

(Link /Black w/sleeve bushing) (Link/noir avec coussinet)

734-2010 Rear Wheel Ass’y 9 x 2.125 Ensemble de roue 9 x 2,125

(Black w/sleeve bush ing) (noir avec coussinet)

734-2044 Rear Wheel Ass’y 9 x 2.125 Ensemble de roue 9 x 2,125 (zag noir)

(Drive/Zag/Blk)

84 731-0981A Hub Cap -Grey Chapeau de moyeu - gris

731-0982A Hub Cap - Beige Chapeau de moyeu - beige

731-1426 Hub Cap -Yellow Chapeau de moyeu - jaune

12A-950

11.22.04

La page charge ...

Yard-Man 950 Series Le manuel du propriétaire

Marque: Yard-Man

Modèle: 950 Series

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Yard-Man 950 Series Owner's manual

Yard-Man 950 Series Le manuel du propriétaire

Ce manuel convient également à

Yard-Man 950 Series Le manuel du propriétaire

dans d''autres langues

Autres documents