Bolens 12AV469Q565 Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire
Safety • Set-Up • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
IMPORTANT:
READ SAFETY RULES AND INSTRUCTIONS
CAREFULLY BEFORE OPERATING EQUIPMENT.
PRINTED IN U.S.A. MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G
21” Self-Propelled Rotary Mower — Model Series 460
1/23/09
769-04801
2
Finding and Recording Model Number
Table of Contents
BEFORE YOU START ASSEMBLING
YOUR NEW EQUIPMENT,
please locate the model plate on the equipment and copy the
model number and the serial number to the sample model
plate provided to the right. You can locate the model plate by
standing at the operating position and looking down at the rear
of the machine.
This Operator’s Manual is an important part of your new equipment. It will help you assemble,
prepare and maintain the unit for best performance. Please read and understand what it says.
Slope Gauge........................................................ 3
Safe Operation Practices ................................... 4
Safety Symbols ................................................... 7
Set-Up & Adjustments ........................................ 8
Operation ........................................................... 10
Maintenance ...................................................... 12
Off-Season Storage .......................................... 13
Trouble Shooting .............................................. 14
Warranty ............................................................ 15
Illustrated Parts Lists ....................................... 16
Please do
NOT
return the unit to the retailer from which it was purchased,
without rst contacting Customer Support.
Customer Support
If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit,
you can seek help from the experts. Choose from the options below:
1. Visit www.bolens.ca for many useful suggestions, click on Customer Support button.
2. Call a Customer Support Representative at 1-800-668-1238.
3. The engine manufacturer is responsible for all engine-related issues in terms of performance, power-rating, specifications,
warranty, and service. Depending on the engine manufacturer, more information is included in this publication or packed
separately with this product.
Please have your units model number and serial number ready when you call. See previous section to locate this information.
You will be asked to enter the serial number in order to process your call.
-4$02/$5#43,)-)4%$
+)4#(%.%2/..'*

8888888888
88888888888
-ODEL.UMBER
.UM£RODEMODÞLE
3ERIAL.UMBER
.UM£RODES£RIE
WWWMTDCANADACOM
3
1
Slope
Gauge
WARNING
Do not mow on inclines
with a slope in excess
of 15 degrees (a rise
of approximately
2-1/2 feet every 10
feet). A riding mower
could overturn and
cause serious injury.
If operating a walk-
behind mower on such
a slope, it is extremely
difficult to maintain your
footing and you could
slip, resulting in serious
injury.
Operate RIDING
mowers up and down
slopes, never across
the face of slopes.
Operate
WALK-BEHIND
mowers across the
face of slopes, never
up and down slopes.
Sight and hold this level with a vertical tree...
or a corner of a building...
or a fence post
Fold along dotted line (represents a 15° slope)
15°
Use this page as a guide to determine slopes where you may not operate safely. Do not operate
your lawn mower on such slopes.
4
2
Safe
Operation
Practices
General Operation
1. Read this operator’s manual carefully in its entirety
before attempting to assemble this machine. Read,
understand, and follow all instructions on the ma-
chine and in the manual(s) before operation. Keep
this manual in a safe place for future and regular
reference and for ordering replacement parts.
2. Be completely familiar with the controls and the
proper use of this machine before operating it.
3. This machine is a precision piece of power equip-
ment, not a plaything. Therefore, exercise extreme
caution at all times. Your unit has been designed to
perform one job: to mow grass. Do not use it for any
other purpose.
4. Never allow children under 14 years old to operate
this machine. Children 14 years old and over should
read and understand the instructions in this manual
and should be trained and supervised by a adult.
5. Only responsible individuals who are familiar with
these rules of safe operation should be allowed to
use this machine.
6. Thoroughly inspect the area where the equipment is
to be used. Remove all stones, sticks, wire, bones,
toys and other foreign objects which could be tripped
over or picked up and thrown by the blade. Thrown
objects can cause serious personal injury.
7. Plan your mowing pattern to avoid discharge of
material toward roads, sidewalks, bystanders and the
like. Also, avoid discharging material against a wall
or obstruction which may cause discharged material
to ricochet back toward the operator.
8. To help avoid blade contact or a thrown object injury,
stay in the operator zone behind the handles and
keep children, bystanders, helpers and pets at least
75 feet from the mower while it is in operation. Stop
machine if anyone enters the area.
9. Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
10. Wear sturdy, rough-soled work shoes and close-
fitting slacks and shirts. Shirts and pants that
cover the arms and legs and steel-toed shoes are
recommended. Never operate this machine in bare
feet, sandals, slippery or light weight (e.g. canvas)
shoes.
11. Do not put hands or feet near rotating parts or under
the cutting deck. Contact with the blade can amputate
hands and feet.
12. A missing or damaged discharge cover can cause
blade contact or thrown object injuries.
13. Many injuries occur as a result of the mower being
pulled over the foot during a fall caused by slipping or
tripping. Do not hold on to the mower if you are falling;
release the handle immediately.
14. Never pull the mower back toward you while you are
walking. If you must back the mower away from a wall
or obstruction first look down and behind to avoid
tripping and then follow these steps:
a. Step back from the mower to fully extend your
arms.
b. Be sure you are well balanced with sure footing.
c. Pull the mower back slowly, no more than half way
toward you.
d. Repeat these steps as needed.
15. Do not operate the mower while under the influence of
alcohol or drugs.
16. Do not engage the self-propelled mechanism on units
so equipped while starting engine.
17. The blade control handle is a safety device. Never
attempt to bypass its operation. Doing so makes the
safety device inoperative and may result in personal
injury through contact with the rotating blade. The
blade control handle must operate easily in both
directions and automatically return to the disengaged
position when released.
18. Never operate the mower in wet grass. Always be
sure of your footing. A slip and fall can cause serious
personal injury. If you feel you are losing your footing,
release the blade control handle immediately and the
blade will stop rotating within three seconds.
19. Mow only in daylight or in good artificial light. Walk,
never run.
20. Stop the blade when crossing gravel drives, walks or
roads.
21. If the equipment should start to vibrate abnormally,
stop the engine and check immediately for the cause.
Vibration is generally a warning of trouble.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain
or emit chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
WARNING
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
manual before at-
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
HEED ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with
any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This
machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety
instructions could result in serious injury or death.
5
22. Shut the engine off and wait until the blade comes to
a complete stop before removing the grass catcher or
unclogging the chute. The cutting blade continues to
rotate for a few seconds after the engine is shut off.
Never place any part of the body in the blade area until
you are sure the blade has stopped rotating.
23. Never operate mower without proper trail shield,
discharge cover, grass catcher, blade control handle or
other safety protective devices in place and working.
Never operate mower with damaged safety devices.
Failure to do so, can result in personal injury.
24. Muffler and engine become hot and can cause a burn.
Do not touch.
25. Never attempt to make a wheel or cutting height
adjustment while the engine is running.
26. Only use parts and accessories made for this machine
by the manufacturer. Failure to do so can result in
personal injury.
27. When starting engine, pull cord slowly until resistance
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster
than you can let go. Broken bones, fractures, bruises
or sprains could result.
28. If situations occur which are not covered in this
manual, use care and good judgment. Call customer
assistance for the name of your nearest servicing
dealer.
Slope Operation
Slopes are a major factor related to slip and fall accidents
which can result in severe injury. Operation on slopes
requires extra caution. If you feel uneasy on a slope, do
not mow it. For your safety, use the slope gauge included
as part of this manual to measure slopes before operating
this unit on a sloped or hilly area. If the slope is greater
than 15 degrees, do not mow it.
Do:
1. Mow across the face of slopes; never up and down.
Exercise extreme caution when changing direction on
slopes.
2. Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles.
3. Always be sure of your footing. A slip and fall can
cause serious personal injury. If you feel you are
losing your balance, release the blade control handle
immediately, and the blade will stop rotating within 3
seconds.
Do Not:
1. Do not mow near drop-offs, ditches or embankments,
you could lose your footing or balance.
2. Do not mow slopes greater than 15 degrees as shown on the
slope gauge.
3. Do not mow on wet grass. Unstable footing could
cause slipping.
Children
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted
to the mower and the mowing activity. They do not
understand the dangers. Never assume that children
will remain where you last saw them.
1. Keep children out of the mowing area and under the
watchful care of a responsible adult other than the
operator.
2. Be alert and turn mower off if a child enters the area.
3. Before and while moving backwards, look behind
and down for small children.
4. Use extreme care when approaching blind corners,
doorways, shrubs, trees, or other objects that may
obscure your vision of a child who may run into the
mower.
5. Keep children away from hot or running engines.
They can suffer burns from a hot muffler.
6. Never allow children under 14 years old to operate a
power mower. Children 14 years old and over should
read and understand the operation instructions and
safety rules in this manual and shou
ld be trained and
supervised by a parent.
Service
Safe Handling Of Gasoline:
1. To avoid personal injury or property damage use
extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
2. Use only an approved gasoline container.
3. Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place contain-
ers on the ground away from your vehicle before
filling.
4. Remove gas-powered equipment from the truck
or trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer with
a portable container, rather than from a gasoline
dispenser nozzle.
5. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
6 Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
7. Never fuel machine indoors because flammable
vapors will accumulate in the area.
8. Never remove gas cap or add fuel while the engine
is hot or running. Allow engine to cool at least two
minutes before refueling.
2
Safe
Operation
Practices
WARNING
This machine is equipped
with an internal combus-
tion engine and should
not be used on or near
any unimproved forest-
covered, brushcovered or
grass-covered land unless
the engine’s exhaust
system is equipped with a
spark arrester meeting ap-
plicable local or provincial
laws (if any).
If a spark arrester is used,
it should be maintained in
effective working order by
the operator.
A spark arrester for the muf-
fler is available through your
nearest engine authorized
service dealer.
Notice regarding Emis-
sions
Engines which are certified
to comply with California
and federal EPA emission
regulations for SORE (Small
Off Road Equipment) are
certified to operate on regu-
lar unleaded gasoline, and
may include the following
emission control systems:
Engine Modification (EM)
and Three Way Catalyst
(TWC) if so equipped.
6
9. Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to provide for fuel
expansion.
10. Replace gasoline cap and tighten securely.
11. If gasoline is spilled, wipe it off the engine and equip-
ment. Move unit to another area. Wait 5 minutes
before starting the engine.
12. Never store the machine or fuel container near an
open flame, spark or pilot light as on a water heater,
space heater, furnace, clothes dryer or other gas
appliances.
13. To reduce fire hazard, keep mower free of grass,
leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.
14. Allow a mower to cool at least 5 minutes before
storing.
General Service:
1. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
2. Before cleaning, repairing, or inspecting, make
certain the blade and all moving parts have stopped.
Disconnect the spark plug wire and ground against
the engine to prevent unintended starting.
3. Check the blade and engine mounting bolts at
frequent intervals for proper tightness. Also, visually
inspect blade for damage (e.g., bent, cracked, worn)
Replace blade with the original equipment manufac-
ture’s (O.E.M.) blade only, listed in this manual. “Use
of parts which do not meet the original equipment
specifications may lead to improper performance
and compromise safety!
4. Mower blades are sharp and can cut. Wrap the blade
or wear gloves, and use extra caution when servicing
them.
5. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
6. Never tamper with safety devices. Check their proper
operation regularly.
7. After striking a foreign object, stop the engine,
disconnect the spark plug wire and ground against
the engine. Thoroughly inspect the mower for any
damage. Repair the damage before starting and
operating the mower.
8. Never attempt to make a wheel or cutting height
adjustment while the engine is running.
9. Grass catcher components, discharge cover, and trail
shield are subject to wear and damage which could
expose moving parts or allow objects to be thrown. For
safety protection, frequently check components and
replace immediately with original equipment manufac-
turer’s (O.E.M.) parts only, listed in this manual. “Use
of parts which do not meet the original equipment
specifications may lead to improper performance and
compromise safety!
10. Do not change the engine governor setting or
overspeed the engine. The governor controls the
maximum safe operating speed of the engine.
11. Check fuel line, tank, cap, and fittings frequently for
cracks or leaks. Replace if necessary.
12. Do not crank engine with spark plug removed.
13. Maintain or replace safety labels, as necessary.
14. Observe proper disposal laws and regulations.
Improper disposal of fluids and materials can harm the
environment.
15. According to the Consumer Products Safety Commis-
sion (CPSC) and the U.S. Environmental Protection
Agency (EPA), this product has an
Average Useful Life
of seven (7) years, or 60 hours of operation. At the
end of the Average Useful Life, buy a new machine or
have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn exces-
sively. Failure to do so can result in accidents, injuries
or death.
Do not modify engine
To avoid serious injury or death, do not modify engine in
any way. Tampering with the governor setting can lead
to a runaway engine and cause it to operate at unsafe
speeds. Never tamper with factory setting of engine
governor.
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions which,
if not followed,
could endanger the
personal safety and/
or property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
HEED ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
7
WARNING: Your Responsibility—Restrict the use of this power machine to persons who
read, understand and follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before
attempting to assemble and operate
DANGER — ROTATING BLADES
To reduce the risk of injury, keep hands and feet away. Do not operate
unless discharge cover or grass catcher is in its proper place. If damaged,
DANGER — BYSTANDERS
Do not mow when children or others are around.
DANGER — HAND/ FOOT CUT
Keep hands and feet away from rotating parts.
DANGER — THROWN DEBRIS
Remove objects that can be thrown by the blade in any direction. Wear
safety glasses.
DANGER — SLOPES
Use extra caution on slopes. Do not mow slopes greater than 1.
WARNINGGASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust
contains carbon monoxide, an odorless and deadly gas.
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during opera-
tion. Allow engine and muffler to cool before touching.
3
Safety
Symbols
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
ITS WARNING!
8
4
Setup and
Adjustment
Figure 4-3
Figure 4-2
NOTE: Reference to
right, left, front and rear
of the lawn mower is in
relation to the operating
position.
Figure 4-1
IMPORTANT
This unit is shipped
without gasoline or
oil in the engine. Fill
up gasoline and oil
as instructed in the
accompanying engine
manual BEFORE
operating your mower.
Figure 4-4
IMPORTANT
Make sure to route
cable outside the
lower handle. Do not
crimp cable while
lifting the handle up.
C
B
A
A
C
D
B
NOTE: The units illustrated may vary slightly from your unit.
1. Remove loose parts and any packing material which
may be between upper and lower handles.
a. Pull up and back on the upper handle to raise the
handle from position A into the operating position
B. See Figure 4-1.
b. Tighten star knobs securing upper handle to
lower handle. Make sure that each carriage bolt is
seated properly in the handle.
2. Locate hairpin clip in one hole on the weld pin on each
side of lower handle.
a. Remove hairpin clip from this hole. Using a pair of
pliers, insert hairpin clip into the other hole on the
weld pin. Repeat on other side.
b. Place one carriage bolt (found in the hardware
pack included with your unit) in the upper hole of
the right handle mounting bracket from the inside
outward. See Figure 4-2. Secure with one star
knobs. Repeat process on the left side.
3. Rope guide Setup as follows, see Figure 4-3:
a. Hold the blade control against the upper handle.
Position A.
b. Slowly pull starter rope out of engine. Position B.
c. Slip starter rope into the rope guide. Position C.
d. Tighten rope guide star knobs. Position D.
4. Insert post on cable ties into holes provided on the
lower handle. Pull cable tie tight and trim excess.
5. To assemble the grasscatcher:
a. Place bag over frame (black plastic side is the bot-
tom of bag.) Insert the hooks on the frame through
the holes in the side plastic channels of the bag.
See Figure 4-4.
b. Secure bag to frame by working the plastic chan-
nels on bag over frame as shown in Figure 4-4. All
of the plastic channels except center top of bag
attach from the outside of bag. Center top of bag
attaches from the inside of bag.
NOTE: This Operator’s
Manual covers
several models. Lawn
Mower features vary by
model. Not all features
discussed (or engines
pictured) in this manual
are applicable to all
Lawn Mower models.
A
B
A
B
B
9
Figure 4-7
4
Setup and
Adjustment
Figure 4-8
WARNING
Figure 4-6
1
2
3
Adjustments
Cutting Height
Each wheel has a height adjustment lever to change the
cutting height of the mower. To change the height of cut,
squeeze adjuster lever toward the wheel, moving up or
down to selected height. See Figure 4-7.
Drive Control
The adjustment wheel is located in the drive control
handle housing and is used to tighten or loosen the drive
belt. You will need to adjust the drive control if the mower
does not propel itself with the drive control engaged
or if the mower’s wheels hesitate with the drive control
engaged. If either of these conditions occur, rotate the
adjustment wheel clockwise to tighten the cable or
counterclockwise to loosen the cable, Figure 4-8.
B
A
Figure 4-5
NOTE: Make certain
bag is turned right side
out before assembling
(warning label will be on
the outside).
NOTE: Make certain
cables are routed to the
outside of the handle so
they are not in the way
when attaching the grass
catcher.
Never operate mower
unless the hooks on
the grass catcher are
firmly seated on the
pivot rod, and the
rear discharge door
rests firmly against
top of the grass
catcher.
All mowers are
equipped with a rear
protective guard. The
guard helps eliminate
projectiles thrown
by the blade from
injuring the operator.
DO NOT REMOVE
THIS GUARD.
7. Attaching Grass Catcher to Mower
a. Lift the rear discharge door on the mower, and place the grass catcher on the pivot rod. Let go of discharge
door so that it rests on the grass catcher. See Figure 4-5.
WARNING: Never operate mower unless the hooks on the grass catcher are firmly seated
on the pivot rod, and the rear discharge door rests firmly against top of the grass catcher.
8. To remove grass catcher and utilize the mulching feature:
a. Lift rear discharge door on the mower as shown in Figure 4-5. Lift grass catcher up and out, off of the pivot
rod. Release rear discharge door to allow it to close rear opening of mower.
9. The side discharge is an optional feature.
If converting to side discharge, make sure grass catcher is off unit and rear discharge door is closed.
a. On the side of the mower deck, lift the hinged mulching plug. See Figure 4-6.
b. Slide the two hooks on the side discharge deflector under the hinge pin on the hinged mulching plug
assembly. Lower the hinged mulching plug.
NOTE: Do not remove the hinged mulching plug at any time, even when you are not mulching.
Tighten
Loosen
10
5
Operating
Your Lawn
Mower
Blade Control Handle
The blade control handle is located on the upper handle
of the mower. See Figure 5-1. The blade control handle
must be depressed in order to operate the unit. Release
the blade control handle to stop the engine and blade.
Drive Control Handle
The drive control handle is located on the upper handle.
Squeeze the drive control handle against the upper
handle to engage drive system. Release the control
handle to disengage the drive system in order to stop,
slow down, or backup.
Mulching Plug (optional)
The mulching plug is used to close the side discharge
chute opening when mulching or bagging grass. Do
not remove the hinged mulching plug at any time, even
when you are not mulching.
Recoil Starter
The recoil starter is attached to the right upper handle.
Stand behind the unit and pull the recoil starter rope to
start the unit.
Know Your Lawn Mower
Cutting Height Adjustment Levers
One adjustment lever is located on each wheel and is
used to adjust the cutting height. All four levers have to be
at the same relative position to ensure uniform cut.
Before Starting
1. Service the engine with gasoline and oil as instructed
in the separate engine manual.
2. Attach spark plug wire to spark plug. If unit is
equipped with a rubber boot over the end of the spark
plug wire, make certain the metal loop on the end of
the spark plug wire (inside the rubber boot) is fastened
securely over the metal tip on the spark plug.
3. Before each use, check for proper drive clutch opera-
tion by performing the following before starting the
engine:
a. With the drive control released, push mower
forward. It should move freely. Pull mower back-
ward. It should move with only a small amount of
resistance.
WARNING
Figure 5-1
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
This blade control
mechanism is a
safety device. Never
attempt to bypass its
operations.
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
Blade Control Handle
Recoil Starter
Height Adjustment
Levers
Grass Bag
Mulching Plug
(optional)
Drive Control Handle
Side Discharge
(optional)
11
5
Operating
Your Lawn
Mower
WARNING
The operation of any
lawn mower can result
in foreign objects
being thrown into
the eyes, which can
damage your eyes
severely. Always wear
safety glasses while
operating the mower,
or while performing
any adjustments or
repairs on it.
Be sure no one other
than the operator is
standing near the lawn
mower while starting
engine or operating
mower. Never run
engine indoors or
in enclosed, poorly
ventilated areas. En-
gine exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands, feet,
hair and loose clothing
away from any moving
parts on engine and
lawn mower.
Figure 5-2
b. If it does not the clutch may not be releasing
completely. Do not start the engine until correc-
tions have been made. Check the control cable
for severe bend, kinks and binding. Also check for
grass build-up around the belt.
To Start Engine
1. If your unit is equipped with a primer, choke or fuel
valve lever operate as instructed in the separate
engine manual packed with your unit.
2. Standing behind the unit, depress the blade control
handle and hold it against the upper handle as shown
in Figure 5-2.
3. Grasp the starter handle as shown and pull slowly
until resistance is felt, then pull rapidly to start engine
and avoid kickback. Return it slowly to the rope guide.
To Stop Engine
1. Release the blade control handle to stop the engine
and blade.
WARNING: The blade continues
to rotate for a few seconds after
the engine is shut off.
2. Disconnect and ground the spark plug wire as
instructed in the separate engine manual to prevent
accidental starting while equipment is unattended.
Using Your Lawn Mower
Be sure the lawn is clear of stones, sticks, wire, or other
objects which could damage the lawn mower or the
engine. Such objects could be accidently thrown by the
mower in any direction and cause serious personal injury
to the operator and others.
WARNING: If you strike a foreign
object, stop the engine. Remove
wire from the spark plug, thor-
oughly inspect the mower for any
damage, and repair the damage
before restarting and operating
the mower. Extensive vibration
of the mower during operation is
an indication of damage. The unit
should be promptly inspected
and repaired.
Operating Tips
1. To engage the drive, squeeze the drive control handle
towards the upper handle. Release the drive control
to slow down when negotiating an obstacle, making a
turn, or stopping.
2. For best results do not cut wet grass.
3. New grass, thick grass, or wet grass may require a
narrower cut.
4. For a healthier lawn, never cut off more than one-third
of the total length of the grass.
5. Your lawn should be cut in the fall as long as there
is growth.
6. If the grass has been allowed to grow in excess of 4
inches, mulching is not recommended. Mow using
the side discharge to reduce the grass height to 3-1/4
inches or less before mulching.
General Recommendations
1. Always observe safety rules when performing
any maintenance.
2. The warranty on this lawn mower does not cover
items that have been subjected to operator abuse
or negligence. To receive full value from warranty,
operator must maintain the lawn mower as
instructed here.
3. Changing of engine-governed speed will void
engine warranty.
4. All adjustments should be checked at least once each
season.
5. Periodically check all fasteners and make sure these
are tight.
NOTE: To operate your unit using the grass catcher,
mulcher or optional side discharge refer to page 9.
/.
/&&
12
6
WARNING
Figure 6-1
Figure 6-2
Lubrication
1. Lubricate the pivot points on the blade control handle
at least once a season with light oil. The blade
control must operate freely in both directions. See
Figure 6-1.
2. If your mower is equipped with ball bearing wheels,
lubricate at least once a season with a light oil, all
other types require no lubrication. However, if the
wheels are removed for any reason, lubricate the
surface of the axle bolt and the inner surface of the
wheel with light automotive oil.
3. Lubricate the torsion spring and pivot point periodi-
cally with light oil to prevent rust. See Figure 6-1.
4. The transmission is pre-lubricated and sealed at the
factory and does not require lubrication.
5. Follow the accompanying engine manual for lubrica-
tion schedule and instruction.
Engine
1. Refer to the separate engine manual for engine
maintenance instructions.
2. Maintain engine oil as instructed in the separate
engine manual packed with your unit. Read and
follow instructions carefully.
3. Service air cleaner every 25 hours under normal
conditions. Clean every few hours under extremely
dusty conditions.
4. Clean the engine regularly with a cloth or brush.
Keep the cooling system (blower housing area) clean
to permit proper air circulation which is essential to
engine performance and life. Be certain to remove all
grass, dirt and combustible debris from muffler area.
Deck
The underside of the mower deck should be cleaned
after each use to prevent a buildup of grass clippings,
leaves, dirt or other matter. If this debris is allowed to
accumulate, it will invite rust and corrosion, and may
prevent proper mulching.
The deck may be cleaned by tilting the mower and scrap-
ing clean with a suitable tool (make certain the spark plug
wire is disconnected).
Replacing Rear Flap
The rear flap is attached to the back of the mower deck. If
the rear flap becomes damaged, replace it by cutting off
the flat end of the wire rod which secures it to the deck
using a pair of side-cutters. Attach the new rear flap using
the new rod provided with the rear flap, bending the ends
of the rod over to secure.
Blade Care
Periodically inspect the blade adapter for cracks,
especially if you strike a foreign object. Replace when
necessary. Follow the steps below for blade service:
1. Remove the bolt and the blade bell support which
hold the blade and the blade adapter to the engine
crankshaft. See Figure 6-2.
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind of
maintenance on your
machine.
Cutting grass in
sandy soil condition
causes abrasive wear
to the blade.
If unit is tipped for
easier access to
blade or belt, tip
mower as specified
in separate engine
manual. If it does not
specify turn mower
on its side making
sure that the air filter
and the carburetor
are up.
Maintenance
2. Remove blade and adapter from the crankshaft.
3. The blade may be resharpened by removing it and
either grinding or filing the cutting edge keeping as
close to the original bevel as possible. Do not attempt
to sharpen the blade while it is still on the mower.
4. It is extremely important that each cutting edge
receives an equal amount of grinding to prevent an
unbalanced blade.
NOTE: Improper blade balance will result in excessive
vibration causing eventual damage to the engine and
mower. Be sure to carefully balance blade after sharpen-
ing. Possible damage resulting from blade unbalance
condition is not the responsibility of the manufacturer.
NOTE: Always remove blade from the adapter for testing
balance.
5. The blade can be tested for balance by balancing it
on a round shaft screwdriver. Remove metal from the
heavy side until it balances evenly.
6 Before reassembling the blade and the blade adapter
to the unit, lubricate the engine crankshaft and the
inner surface of the blade adapter with light oil.
13
6
WARNING
Figure 6-3
7. Install the blade adapter on the crankshaft with the
“star” away from the engine. See Figure 6-2. Place
the blade with the side marked “bottom” (or with part
number) facing away from the adapter. Align the blade
bell support over the blade with the tabs in the holes
of the blade and insert the hex bolt.
8. Tighten the hex bolt to the torque listed below:
Blade Mounting Torque
Center Bolt 450 in. lb. min., 600 in.lb. max.
To insure safe operation of your unit, ALL nuts and bolts
must be checked periodically for correct tightness.
Belt Care
1. Remove two shoulder screws securing front drive cover
to mower deck. See Figure 6-3. Press inward on sides
of front drive cover and release tabs that secure it to
the height adjuster brackets. Remove drive cover from
mower.
2. Loosen screw holding belt tension spring to transmission.
See Figure 6-3 inset. Do not remove screw completely.
As you loosen it, tension on the belt will be released.
3. Tip mower on its side with the air filter up to access belt
from underside of mower and remove blade as described
in the previous section. Refer to Figure 6-3.
4. Press inward on tab on the engine baffle to release it from
the baffle bracket. See Figure 6-4.
5. Slide belt off of engine pulley and thread through the
opening in the deck. See Figure 6-5.
NOTE: When removing belt on units with a 25mm adapter,
the pulleys and washer(s) may also break free from the
crankshaft. Be sure to make note of the orientation of these
items for reassembly.
6. Replace with new belt, making sure belt is firmly seated
on engine pulley while pulling from the other side and
sliding it around the transmission pulley.
7. Reattach engine baffle and reassemble blade as
described in the previous section.
8. Turn mower back over and make sure belt is seated on
the transmission pulley. Pivot the belt keeper wire back
into its operating position and snap into the slot provided.
9. Reassemble front drive cover.
10. Tighten screw loosened earlier to secure belt tension
spring to the transmission. Reassemble front drive cover.
Off-Season Storage
The following steps should be taken to prepare your lawn
mower for storage.
1. Clean and lubricate mower thoroughly as described in
the lubrication instructions.
2. We do not recommend the use of a pressure washer
or garden hose to clean your unit.
3. Refer to engine manual for correct engine
storage instructions.
4. Coat mower’s cutting blade with chassis grease to
prevent rusting.
5. Store mower in a dry, clean area. Do not store next to
corrosive materials, such as fertilizer.
Maintenance
We do not recommend
the use of pressure
washers or garden
hose to clean your
unit. These may cause
damage to electrical
components, spindles,
pulleys, bearings, or
the engine. The use
of water will result in
shortened life and
reduce serviceability.
When removing the
cutting blade or belt,
protect your hands
with a pair of heavy
gloves or use a heavy
rag to hold the blade.
An unbalanced blade
will cause excessive
vibration when rotat-
ing at high speeds. It
may cause damage
to mower, and could
break causing per-
sonal injury.
Figure 6-4
Figure 6-5
NOTE: When storing any type of power equipment in
a poorly ventilated or metal storage shed, care should
be taken to rust-proof the equipment. Using a light oil or
silicone, coat the equipment, especially cables and all
moving parts of your lawn mower before storage.
14
For repairs beyond
the minor adjust-
ments listed here,
contact an authorized
service dealer.
7
Trouble
Shooting
CauseProblem
Remedy
Engine fails to start
1. Blade control handle disengaged.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not primed.
5. Faulty spark plug.
6. Blocked fuel line.
7. Engine flooding.
8. Fuel valve (if quipped) closed.
9. Engine not choked (if equipped with
choke).
10. Burnt fuse. (Electric Start only).
1. Engage blade control handle.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
4. Refer to engine manual.
5. Clean, adjust gap, or replace.
6. Clean fuel line.
7. Wait a few minutes to restart, but do not prime.
8. Open fuel valve. See engine manual.
9. Choke engine. See engine manual.
10. Replace fuse (see Maintenance Section).
Engine runs erratic 1. Connect and tighten spark
plug wire.
2. Clean fuel line; fill tank with clean, fresh
gasoline.
3. Clear vent.
4. Drain fuel tank and carburetor. Refill with fresh
fuel.
5. Refer to engine manual.
6. Refer to engine manual.
1. Spark plug wire loose.
2. Blocked fuel line or stale fuel.
3. Gas cap vent plugged.
4. Water or dirt in fuel system.
5. Dirty air cleaner.
6. Carburetor out of adjustment.
Engine overheats
1. Fill crankcase with proper oil.
2. Refer to the engine manual packed with your
unit.
3. Remove blower housing and clean.
4. Refer to engine manual.
1. Engine oil level low.
2. Dirty air filter.
3. Air flow restricted.
4. Carburetor not adjusted properly.
Occasional skip (hesitates)
at high speed
1. Adjust gap to .030”. Refer to engine manual.
2. Refer to engine manual.
1. Spark plug gap too close.
2. Carburetor idle mixture adjustment
improperly set.
Idles poorly
1. Reset gap to .030” or replace spark plug.
Refer to engine manual.
2. Refer to engine manual.
3. Refer to engine manual.
1. Spark plug fouled, faulty or gap too
wide.
2. Carburetor improperly adjusted.
3. Dirty air cleaner.
1. Cutting Blade loose or unbalanced.
2. Bent cutting blade.
1. Tighten blade and adapter. Balance blade
2. Replace blade.
Excessive vibration
1. Wheels not positioned correctly.
2. Dull blade.
Uneven cut
1. Place all four wheels in same height position.
2. Sharpen or replace blade.
1. Wet grass.
2. Excessive high grass.
3. Dull blade.
1. Do not mow when grass is wet;
wait until later to cut.
2. Mow once at a high cutting height, then mow
again at desired height or make a narrower
cutting path.
3. Sharpen or replace blade.
Mower will not mulch
grass
1. Belt not installed properly.
2. Debris clogging drive operation.
1. Checking belt for proper pulley installation and
movement.
2. Clean out debris.
Wheels will not propel
15
8
Warranty
Failure to comply
with suggested
maintenance
and lubrication
specifications will
void warranty.
4 YEAR LIMITED WARRANTY
For FOUR YEARS from the date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option, repair
or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
This warranty does not cover:
1. Any part which has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper mainte-
nance or alteration; or
2. The unit if it has not been operated and/or maintained in accordance with the owner’s instructions furnished with the
unit; or
3. The engine or motor or component parts thereof which carry separate warranties from their manufacturers. Please
refer to the applicable manufacturer’s warranty on these items; and read engine warranty statement below, or
4. Batteries and normal wear parts except as noted below. Log splitter pumps, valves and cylinders or component parts
thereof are covered by a one year warranty; or
5. Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake,
clutch or deck; or
6. Normal deterioration of the exterior finish due to use or exposure.
Full Ninety Day Warranty on Battery (if equipped): For ninety (90) days from the date of retail purchase, if any
battery included with this unit proves defective in material or workmanship and our testing determines the battery will
not hold a charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.
Additional Limited Thirty Day Warranty on Battery (if equipped): After ninety (90) days but within one hundred
twenty (120) days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective battery, for the
original purchaser, for a cost of one-half (½) of the current retail price of the battery in effect at the date of return.
Full Ninety Days Warranty on Normal Wear Parts: Normal wear parts are defined as belts, blade adaptors, blades,
grass bags, seats, tires, rider deck wheels and clutch parts (friction wheels). These parts are warranted to the original
purchaser to be free from defects in material and workmanship for a period of ninety (90) days from the date of retail
purchase.
How to Obtain Service: Warranty service is available, with proof of purchase, through your local authorized service
dealer or distributor. If you do not know the dealer or distributor in your area, please call, toll free 1-800-668-1238. The
return of a complete unit will not be accepted by the factory unless prior written permission has been extended by MTD
PRODUCTS LIMITED.
Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are
the responsibility of the purchaser. Transportation charges for any part submitted for replacement under this warranty
must be paid by the purchaser unless such return is requested in writing by MTD PRODUCTS LIMITED.
Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited
in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the
sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale of its products.
MTD PRODUCTS LIMITED will not be liable for incidental or consequential loss or damage.
4 YEAR LIMITED WARRANTY ENGINES
This limited warranty doubles the time periods of the engine manufacturer’s limited warranty which is enclosed in the
owner’s information package.
12.08.06
16
50
46
55
41
43
59
58
54
25
11
21
53
52
51
37
38
39
49
48
45
44
42
47
30
29
57
31
32
33
41
40
34
28
1
2
5
6
7
9
10
11
12
14
16
17
3
4
8
13
15
24
27
62
35
36
23
22
4
26
18
20
19
21
11
64
61
41
56
41
63
17
9
IMPORTANT
For a proper working
machine, use Factory
Approved Parts.
V-BELTS are specially
designed to engage
and disengage safely.
A substitute (non OEM)
V-Belt can be danger-
ous by not disengaging
completely.
For parts and/or
accessories refer to
customer support on
page 2.
Adressez-vous au
«Service après-vente»
à la page 2 pour ce qui
concerne les pièces
et/ou accessoires.
Parts List
Pièces
détachées
REF PART
NO. NO.
N° DE N° DE
RÉF PIÈCE DE SCRIP TION DE SCRIP TION
1 712-0214 Hex L-Nut 3/8-24 Contre-écrou à six pans 3/8-24
2 736-0105 Cupped Washer Rondelle creuse
3 756-04132 Pul ley, 3.82 x .313 x .68 Poulie 3,82 x 0,313 x 0,68
4 710-04329 Torx Screw Vis torx
5 707-04567A Trans mis sion Bracket Sup port de la trans mis sion
6 726-04043 Push Nut Écrou poussée
7 736-04178A Slot ted Washer Rondelle
8 731-05187 Clutch Le ver Lev ier de l'embrayage
9 721-04110 O-ring Bague en «O»
10 731-05099A Up per Hous ing Carter de la logement supérieur
11 721-04107 Oil Seal Joint
12 741-04116 Ball Bear ing Roulement à billes
13 710-04374 Hex Screw Vis à tête hex.
14 711-04317 Pin ion Shaft Arbre à pin ion
15 715-04030 Dowel Pin Goupille
16 715-0129 Spirol Pin Goupille
17 707-04409A Shifter Fork
18 711-04429 Out put Shaft Arbre-sor tie
19 736-0572 Flat Washer Rondelle plate
20 736-04224 Flat Washer Rondelle plate
21 741-04106 Plas tic Bush ing Coussinet
22 731-04883 Lower Hous ing Ass’y Carter de la logement
23 717-04194 28 Tooth Gear Engrenage 28 dents
24 732-04290 Com pres sion Spring Ressort de com pres sion
25 750-04405 Sleeve Spacer 1.8" Lg. Entretoise 1,8 po de lg.
26 750-04404 Sleeve Spacer 9.10" Lg. Entretoise9,10 po de lg.
27 710-1008 Hex Wash TT Sems Scr 3/8-16 x 1.875 Vis autotaraudée 3/8-16 x 1,875
28 787-01278 21" Deck Tablier 21 po
29 710-0599 Hex Wash S-Tapp Scr 1/4-20 x .50 Vis autotaraudeuse à rond. hex. 1/4-20 x 0,50
30 736-0270 Cupped Washer .265 ID x .75 OD x .062 Rondelle creuse 0,265 DI x 0,75 DE x 0,062
31 687-02055 Com plete Mulch Plug Plaque de déchiquetage complet
32 17032A Chute Hinge Charnière de déflecteur
33 732-1014 Tor sion Spring Ressort de tor sion
34 747-0710 Hinge Pin Axe de charnière
35 618-04377A Trans mis sion Ass’y Com plete Transessieu complet
36 687-02194A RH Height Ad just ment As sem bly En sem ble de réglage de hau teur - CD
687-02193A LH Height Ad just ment As sem bly En sem ble de réglage de hau teur - CG
37 787-01298 Height Ad juster Plate - RH Plaque de réglage de hau teur - CD
787-01299 Height Ad juster Plate - LH Plaque de réglage de hau teur - CG
38 687-02344 Height Ad juster Pivot Plate Ass'y Plaque de pivot - réglage de hau teur
39 732-0706 Spring Le ver Front RH Lev ier de ressort avant - CD
732-0707 Spring Le ver Front LH Lev ier de ressort avant - CG
40 782-5002B Front Baf fle Déflecteur de déchiquetage avant 21 po
41 712-04065 Hex L-FlangeNut 3/8-16 Gr. F, Ny lon Contre-écrou à embase 3/8-16 Qual. F, ny lon
42 734-2042 Wheel Ass'y 8 x 2.125 Gear Zag En sem ble de roue 8 x 2,125 Gear Zag
43 734-02004A Wheel Ass'y 8 x 2.125 Idle BB Zag En sem ble de roue 8 x 2,125 Idle BB Zag
44 710-04531 Pan Scr. 1/4-20 x .390 Vis 1/4-10 x 0,390
45 717-1762 Spur Gear 14T RH Engrenage 14 dents droite
717-1761 Spur Gear 14T LH Engrenage 14 dents gauche
46 715-0221 Pin Goupille
47 782-7551A Wheel Dust Cap Cha peau de moyeu
48 716-0102 Snap Ring for 1.0" shaft Jonc d’arrêt pour arbre 1,0 PO
49 736-0474 Flat Washer 1.5 OD x .03 Rondelle plate 1,50 DE x 0,03
50 710-0216 Hex Cap Screw 3/8-16 x .75 Vis à cha peau à six pans de 3/8-16 x 0,75
51 736-0447 Wave Washer Rondelle ondulée
52 748-04160 Bear ing Sup port Sup port de roulement
53 741-0604A Bear ing Sleeve Manchon de roulement
54 732-0708 Bear ing Re tainer Retenue de roulement
55 720-0426 Height Ad juster Knob Bou ton
56 710-1652 Hex Wash Hd TT Scr. 1/4-20 x .625 Vis taraudée 1/4-20 x 0,625
57 738-04266 Shoul der Screw
.50 Dia. X .385 Vis à épaulement 0,50 dia. X 0,385
58 687-02333 Pivot Arm As sem bly - RH En sem ble de bras de pivot - CD
687-02332 Pivot Arm As sem bly - LH En sem ble de bras de pivot - CG
59 687-02078 Rear Spring Le ver Lev ier de ressort arrière
60 720-0312 Foam Grip Poignée de mousse
61 787-01382A RH Han dle Bracket Sup port de guidon CD
787-01381A LH Han dle Bracket Sup port de guidon CG
62 687-02270A LH Han dle Bracket As sem bly En sem ble de sup port du guidon CG
687-02271A RH Han dle Bracket As sem bly En sem ble de sup port du guidon CD
63 736-0182 Spring Washer .50 ID x 1.0 OD x .022 Rondelle ressort 0,50 DI x 1,0 DE x 0,022
64 731-01426A Hub Cap - Yel low Cha peau de moyeu jaune
731-0981C Hub Cap Grey Ra dial Moyeu de cha peau - gris
12AV46QB
1.22.09
18
16
22
3
15
14
5
4
10
13
39
26
40
43
25
24
21
20
30
31
35
2
7
42
41
29
33
19
32
44
28
17
18
6
12
11
9
8
36
52
47
51
50
46
49
53
48
2
1
38
34
37
56
57
33
54
38
55
34
37
29
19
9
IMPORTANT
For a proper working
machine, use Factory
Approved Parts.
V-BELTS are specially
designed to engage
and disengage safely.
A substitute (non OEM)
V-Belt can be danger-
ous by not disengaging
completely.
REF PART
NO. NO.
N° DE N° DE
RÉF PIÈCE DE SCRIP TION DE SCRIP TION
1 746-04206A Drive Ca ble Câble de la commande1
2 731-04150C Rear Baf fle 21" Rear Dis charge Déflecteur arrière 21 po éjection arrière
3 710-01241 Hex Lock Screw 1/4-15 x 1.0 Vis à tête hex. 1/4-15 x 1,0
4 731-2626 Bail Cover - Black Couvercle - noir
731-04204 Bail Cover - Red Couvercle - rouge
5 747-1161A Blade Con trol Han dle Poignée de commande de la lame
6 749-04206B Up per Han dle Guidon supérieur
7 787-01258A Ca ble Mount ing Bracket Sup port
8 753-06060 Con trol Le ver Ass'y En sem ble de lev ier de la commande
9 720-0279 Knob Bou ton
10 720-04072 Knob - Star 5/16-18 Bou ton - étoile 5/16-18
11 710-1205 Rope Guide Bolt Boulon de guidage de cor don
12 746-0957 Con trol Ca ble 37.25" Lg. Câble de commande de la lame 37,25 po de lg.
13 710-1174 Car riage Bolt 5/16-18 x 2.0 Boulon ordi naire 5/16-18 x 2,0
14 726-0240 Ca ble Tie Attache câble
15 714-0104 Int. Cot ter Pin .072 x 1.13" Lg. Goupille fendue int. 0,072 x 1,13 po de lg.
16 712-0397 Wing Nut Écrou à oreilles
17 664-04007A Grass Bag -Ge neric Sac à herbe -Ge neric
664-04011 Grass Bag -Troybilt Sac à herbe -Troybilt
664-04068 Grass Bag (MTD Gold) Sac à herbe (MTD Gold)
664-04027 Grass Bag Yard-man Sac à herbe (Yard-man
18 747-04080A Grass Bag Frame Bâti de sac à herbe
20 731-05642 Trail Shield Abattant de pro tec tion arrière
21 731-06885 Rear Dis charge Door Porte d’éjection arrière
22 710-0703 Car riage Bolt 1/4-10 x .75 Boulon ordi naire 1/4-20 x 0,75
24 747-04588 Pivot Rod (w/12" rear wheels) Tige de pivot (avec pneu arrière 12 po)
747-04587 Pivot Rod (w/8" rear wheels) Tige de pivot (avec pneu arrière 8 po)
25 731-05250 Trans mis sion Cover (Grey) Couvercle de la trans mis sion (gris)
731-05013A Trans mis sion Cover (Black) Couvercle de la trans mis sion (noir)
731-05020A Trans mis sion Cover (Black Troybilt) Couvercle de la trans mis sion (noir Troybilt)
26 710-1650 Shoul der Screw #12-24 Vis à épaulement no12 -24
28 749-0928A Lower Han dle Guidon inférieur
29 754-04082A V-Belt Courroie trapézoïdale
30 756-04161 Up per Pul ley Half 25mm x 2.62 Poulie demi - supérieur 25mm x 2,62
31 756-04160 Lower Pul ley Half 25mm x 2.62 Poulie demi - inférieur 25mm x 2,62
32 750-04818 Sleeve Spacer 25 mm ID x 1.375 x .375 Entretoise 25 mm ID x 1,375 x 0,375
33 748-04082 Blade Adapter Adaptateur de la lame
34 736-0524B Blade Bell Sup port Sup port de la lame
35 736-0447 Space Washer Rondelle
36 736-0277 Flat Washer Rondelle plate
37 710-1257 Hex Bolt 3/8-24 x 2.5" Lg. Boulon hex. 3/8-24 x 2,50 po de lg.
38 742-0741 21" Mulch ing Blade Lame déchiquetage 21 po
39 731-04177 Chute De flec tor Déflecteur de la goulotte
40 732-04317 Ex ten sion Spring Ressort d'extention
41 732-04294 Belt Keeper Wire Fil
42 710-4329 Torx Screw Vis torx
43 710-0896 Screw 1/4-14 x 0.625 Vis 1/4-14 x 0,625
44 732-04090A Tor sion Spring RH Ressort de tor sion CD
*** 46 725-04323 12V Bat tery Batterie
*** 47 725-04329 Bat tery Charger Chargeur de la batterie
*** 48 725-0240 Ca ble Tie Attache câble
*** 49 728-0199 Rivet Rivet
*** 50 725-04347 Key Switch Interrupteur
*** 51 725-0201 Key Clé
*** 52 625-04029 Elec tric Starter Har ness Ass'y Faisceau
*** 53 710-1667A Screw, #10-16 x .750 Vis no. 10-16 x 0,750
** 54 731-06029 En gine Baf fle Déflecteur du moteur
** 55 787-01593 Bracket Sup port
** 56 656-04045 Drive Pul ley Ass'y Poulie d'entraînement
** 57 736-04389 Wave Washer 1.35 x 1.05 x 0.015 Rondelle 1,35 x 1,05 x 0,015
* w/stain less steel decks/avec coupe en acier inoxydable
** w/painted steel decks/avec les pla teaux de coupe en acier et revêtement poudré
*** Mod els w/elec tric start only/Modèles avec démarreur électrique seulement
12AG563Q
1.23.09
For parts and/or
accessories refer to
customer support on
page 2.
Adressez-vous au
«Service après-vente»
à la page 2 pour ce qui
concerne les pièces
et/ou accessoires.
Parts List
Pièces
détachées
17
NOTES:
For parts and/or
accessories refer to
customer support on
page 2.
Adressez-vous au
«Service après-vente»
à la page 2 pour
ce qui concerne
les pièces et/ou
accessoires.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Bolens 12AV469Q565 Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire

dans d''autres langues