Hestan KDW24 Guide d'installation

INDOOR CLEANING

Dishwasher

KDW

Installation Manual

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY

BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUCE

THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP

THIS MANUAL FOR FUTURE REFERENCE.

Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of

this or any other appliance.

Installation and service must be performed by a qualiﬁed installer or service agency.

DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS

SPECIFICALLY RECOMMENDED IN THE MANUAL. IMPROPER INSTALLATION,

SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER

TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY A

QUALIFIED TECHNICIAN.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.

HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY, OR DEATH.

EN

SAFETY DEFINITIONS

DANGER. THIS INDICATES INFORMATION AND WARNINGS WHICH,

IF NOT OBSERVED, MAY COMPROMISE PERSONAL SAFETY OR DAMAGE

THE APPLIANCE.

DANGER OF ELECTROCUTION. THIS INDICATES INFORMATION AND

WARNINGS OF AN ELECTRICAL NATURE WHICH, IF NOT OBSERVED,

MAY COMPROMISE PERSONAL SAFETY OR DAMAGE THE APPLIANCE.

THIS HIGHLIGHTS GENERAL INFORMATION AND WARNINGS AND

INDICATES THAT DAMAGE TO THE APPLIANCE OR PROPERTY MAY

OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

TABLE OF CONTENTS

EN

1

When properly cared for, your Hestan appliance will provide safe, reliable service for many

years. When using this appliance, basic safety practices must be followed as outlined below.

IMPORTANT: Save these instructions for the local Utility Inspector’s use.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This appliance is NOT designed for installation in manufactured (mobile) homes or

recreational park trailers. Do NOT install this appliance outdoors.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning

power ON, be sure all controls are in the OFF position. Failure to do so can

result in death or electrical shock.

ELECTRICAL GROUNDING

• This appliance must be grounded. Grounding reduces the risk of electric shock in the

event of a short circuit. Read the ELECTRICAL CONNECTIONS section of this manual

for complete instructions.

• DO NOT ground to a gas pipe.

• DO NOT use an extension cord with this appliance.

• DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A fuse in the NEUTRAL

or GROUNDING circuit could result in an electrical shock.

1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN

2 MODEL NUMBERS

2 RATING LABEL

2 REGULATORY / CODE REQUIREMENTS

3 LOCATION AND INSTALLATION

12

MOUNTING THE OVERLAY DOOR PANEL

13 ATTACHING THE SIDE GASKETS

14

15 ELECTRICAL CONNECTIONS, SAFETY AND CAUTION

COMPLETING INSTALLATION AND TESTING

Hestan appliance such as the model and serial number and

electrical rating.

The rating label is located on the right side of the door edge.

If service is necessary, contact Hestan Customer Care with the

model and serial number information shown on the label.

DISHWASHER MODELS

Model No. Description Circuit Breaker Req’d

KDW24 24” Dishwasher, Stainless Door 15 Amp

KDW24-OV 24” Dishwasher, Overlay Door 15 Amp

RATING LABEL

TYPICAL RATING LABEL

MODEL NUMBERS

RATING LABEL

KDW24-XX

NOTE: -XX indicates color model.

-BK for Stealth - Black

-YW for Sol - Yellow

-PP for Lush - Purple

-GG for Paciﬁc Fog - Graphite Gray

-WH for Froth - White

-OR for Citra - Orange

-BU for Prince - Blue

-RD for Matador - Red

-BG for Tin Roof - Burgundy

-GR for Grove - Green

-TQ for Bora Bora - Turquoise

24” Dishwasher, Color Door 15 Amp

2

The rating label contains important information about your

REGULATORY / CODE REQUIREMENTS

Installation of this dishwashing appliance must be made in accordance with local codes. In the

absence of local codes, this unit should be installed in accordance with the National Electrical

Code and local codes.

This appliance must be electrically grounded in accordance with local codes or in the absence

of local codes with the National Electrical Code

ANSI/NFPA 70

, or Canadian Electrical code

CSA C22.1

.

EN

LOCATION AND INSTALLATION

UNPACKING AND PLACEMENT

TOOLS

Remove the outer carton and packing materials Do not remove the plastic ﬁlm covering

the stainless-steel surfaces. This ﬁlm protects the ﬁnish from scratches until the

appliance is installed in its ﬁnal position.

The unit is heavy and should be handled with care. Use proper safety equipment, such as

gloves and 2 persons to move the appliance into position to avoid injury and to avoid

damage to the ﬂoor or the appliance itself.

NOTICE

DO NOT USE A HAND TRUCK OR DOLLY ON THE FRONT OR REAR

OF THE DISHWASHER. HANDLE AND MOVE FROM THE SIDES ONLY.

Do not lift or carry the appliance by the door or handle. This could damage the door hinges.

PREPARATION

Before moving the dishwasher, protect any ﬁnished ﬂooring and secure the door closed

to prevent damage. DO NOT lift the dishwasher by the door handle.

Make sure that power can be provided to the location selected.

The following tools are needed for the installation of the dishwasher:

• Tape measure and straight edge or ruler

• Pencil

• Philips screw driver

• Level

• Plumbing pliers

• Hand or saber saw

• 13mm open-end or adjustable wrench

• File

• Drill and drill bit

• Safety gloves and goggles

3

The following pages provide the necessary information for proper installation of the dishwasher

and are arranged as follows:

• Technical data.

• Installation cutout dimensions, required clearances and mounting instructions.

• Electrical requirements and connections.

• Leak inspection and testing.

STEPS FOR INSTALLATION

EN

The kit supplied with the dishwasher comprises:

• 1 steel adhesive steam guard (A)

• 1 template for door panel (B)

• 2 hooks for door panel (C)

• 8 screws for securing the door panel hooks (D)

• 2 screws for securing the door (E)

• 4 screws for ﬁxing the dishwasher to the adjacent walls (F)

• 2 upper ﬁxing screws (G)

• 2 screw caps (H)

The kit supplied with the dishwasher comprises:

•

H

(KDW24-OV model also contains B, C, D, and E)

INSTALLATION KIT SUPPLIED WITH DISHWASHER

PRODUCT / CUT-OUT DIMENSIONS

LOCATION AND INSTALLATION

4

(continued)

Cut-out Dimensions:

D (height) E (width)

F (depth)

22-5/8” min depth

57.5 cm

23-11/16” wide

60.2 cm

33-7/8” height

86.1 cm

Product Dimensions:

D

E

F

EN

LOCATION AND INSTALLATION

CAUTION

LEVELING

5

(continued)

ON THE SHARP EDGES OF THE APPLIANCE.

position. The sides and rear of the appliance can lie against kitchen units or walls.

If the dishwasher is installed next to a heat source, separate it

panel in order to prevent overheating and malfunctions.

ABSOLUTELY FORBIDDEN. A DISHWASHER CAN BE BUILT-IN

UNDERNEATH A CONVENTIONAL HOB PROVIDED THERE IS NO

BREAK IN THE KITCHEN WORKTOP, AND THE DISHWASHER

AND HOB ARE INSTALLED AND SECURED CORRECTLY, SO

THAT NO HAZARDS ARE GENERATED.

MAKE SURE THE DISHWASHER HAS BEEN CORRECTLY IN-

STALLED AND GROUNDED BY A QUALIFIED FITTER. THIS

SAFETY REQUIREMENT MUST BE MET. IN CASE OF DOUBT,

CALL IN A QUALIFIED FITTER. THE MANUFACTURER DE-

CLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS

OR PROPERTY RESULTING FROM THE FAILURE TO GROUND

THE APPLIANCE OR FROM A DEFECTIVE GROUND CON-

NECTION .

BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT

THE MAINS POWER SUPPLY FROM THE WORK AREA.

Remove the polystyrene rack blocks. Position the appliance in the chosen installation

with a heat insulating

BUILDING-IN A DISHWASHER BELOW A COOKTOP IS

DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF

Level the appliance using the adjustable feet on the bottom. Use an open-ended wrench

or socket to rotate the feet until the dishwasher is perfectly level. The rear foot can be

adjusted with a 8 mm wrench or socket. Use a level to be certain the dishwasher

is perfectly level. Leveling is vital for assuring correct dishwasher operation .

Make sure to leave a gap of at least 7/64” (3mm) between the top of the dishwasher

and the bottom surface of the countertop.

EN

through the adjacent cabinetry. These connections must never be behind the dishwasher.

The inlet and drain hoses can be pointed in all directions but make sure that they are not

bent, crushed or too tight. Tighten the ring nut after pointing the hoses in the required

direction.

The illustration below indicates the distances to maintain between the dishwasher and

the various connections.

DO NOT COVER OR CRUSH THE CORD PLUG.

A = 47” / 1200mm

B = 59” / 1500mm

C = 63” / 1600mm

D = min. 16” / 400mm

A

B

D

C

ELECTRICAL AND WATER CONNECTIONS

6

FIRE HAZARD!

Install the dishwasher to allow ease of access to the electrical and water connections

hoses and power cord.

Make sure there are no rough edges that could damage the power cord or

hoses. If the dishwasher is installed in a metal unit protect the edge of the

through hole for the hoses and power cord with a gasket. Do not use extension

cords when making the electrical connection as these do not guarantee safety.

ATTENTION!

INSTALLING THE DISHWASHER IN A NARROW SPACE MAY BEND

OR CRUSH THE POWER CORD. TAKE GREAT CARE IN ORDER TO

REDUCE THE POSSIBILITY OF DAMAGING THE POWER CORD

WHEN INSTALLING OR REMOVING THE APPLIANCE.

A through hole with a diameter of at least 5/32” (8mm) is required to pass the

LOCATION AND INSTALLATION

(continued)

EN

A

PREVENTING THE RISK OF CLOGGING OR DAMAGE:

IF THE PLUMBING IS NEW OR HAS NOT BEEN USED FOR A LONG TIME

TIME, BEFORE CONNECTING TO THE WATER SUPPLY CHECK THAT THE

WATER IS CLEAR AND FREE OF IMPURITIES, TO PREVENT DAMAGE TO THE

APPLIANCE. THE DISHWASHER MUST ALWAYS BE CONNECTED TO THE

THE WATER SYSTEM WITH NEW HOSES. OLD OR USED HOSES MUST

NEVER BE RE-USED.

LOCATION AND INSTALLATION

CONNECTING THE WATER SUPPLY

CONNECTING TO A WATER TAP

7

(continued)

Firmly secure the hose by tightening the relative ring nut with your hands;

nish by tightening another 1/4 turn using a pair of plumbing pliers.

The dishwasher can be ﬁ lled with water at a temperature of less than 140°F 60°C.

If the appliance is ﬁ lled with hot water, washing times will be reduced by about

20 minutes, but efﬁ ciency will be slightly impaired. Make the connection to the

domestic hot water tap using the same methods described for connecting the

appliance to the cold water tap.

• Recommended temperature: 49°C (120°F), max. 60°C (140°F).

• Recommended water pressure: 0.5 - 9 bar (7 -130 PSI).

A rubber hose connected to a sink spray may burst if installed on the

same pipes feeding the dishwasher. If your sink is ﬁ tted with this

accessory, remove the hose and plug the hole.

Connect the inlet hose to a threaded 3/4” cold water tap tting the supplied lter.

If the pressure is too high, use a pressure reducer.

EN

Do not cut the inlet hose.

If the hose is cut, the dishwasher will not work, water will leak and you may be

injured.

If the hose is too long, wind it up neatly and place it behind the appliance.

The cable harness and electrical components must not come into contact with

the hydraulic system and the water inlet and drain hoses.

When connecting the dishwasher drain hose to the sink make sure that the

hose is not bent in order to prevent cracks or breakages that could damage it.

8

CONNECTING TO A WATER TAP

MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE

DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR

ON WHICH THE DISHWASHER WILL BE INSTALLED.

Connect the dishwasher drain hose to the “T” union of the drain using a

1-1/2 to 2” (38 to 50 mm) screw clamp* if necessary, cut the end of the

dishwasher drain hose (DO NOT cut the corrugated section).

* Available from any plumbing store

CONNECTING TO A “T” UNION FOR DRAINAGE

(continued)

LOCATION AND INSTALLATION

(continued)

EN

MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE

DRAIN LINE AND AT LEAST 15-3/4” (400 mm) ABOVE THE FLOOR

ON WHICH THE DISHWASHER WILL BE INSTALLED.

1.

Remove the cover of the waste disposal unit (A) .

2.

Connect the dishwasher drain hose (B ) to the air gap (C)

using the wide spring

corrugated section). If the drain hose has been cut, use a 38 to 50 mm (1-1/2 to 2”)

screw clamp*.

3.

To connect the air gap (ref. C ) to the waste disposal unit inlet (F)

use a rubber union* (G ) with spring or screw clamps*

* Available from any plumbing store

C

D

B

G

H

A

E

LOCATION AND INSTALLATION

CONNECTING TO A WASTE DISPOSAL UNIT WITH AN AIR GAP

CONNECTING TO THE AIR GAP WITHOUT A WASTE DISPOSAL UNIT

9

(continued)

clamp (D ) ; if necessary, cut the

end of the dishwasher drain hose (E ) (do not cut the

MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE

DRAIN LINE AND AT LEAST 15-3/4” (400 mm) ABOVE THE FLOOR

ON WHICH THE DISHWASHER WILL BE INSTALLED

1.

Connect the dishwasher drain hose (ref. B ) to the air gap (C )

using the wide spring

corrugated section). If the drain hose has been cut, use a 38 to 50 mm (1-1/2 to 2”)

screw clamp*.

2.

To connect the air gap (ref. C ) to the waste disposal unit inlet (F )

use a rubber union* (G ) with spring or screw clamps*

* Available from any plumbing store

clamp (D) ; if necessary, cut the

end of the dishwasher drain hose (E ) (do not cut the

B

C

A

F

G

D

E

EN

B

D

C

A

10

CONNECTING TO A WASTE DISPOSAL WITHOUT AN AIR GAP

CONNECTING TO THE OUTLET

MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE

DRAIN LINE AND AT LEAST 15-3/4” (400 mm) ABOVE THE FLOOR

ON WHICH THE DISHWASHER WILL BE INSTALLED.

1.

Remove the cover of the waste disposal unit (A) .

2.

Connect the dishwasher drain hose (B ) to the waste disposal unit inlet (C),

* Available from any plumbing store

using the wide spring clamp (D).

RATINGS ON THE NAME PLATE OF THE APPLIANCE, WHICH IS POSITIONED

ON THE INNER EDGE OF THE DOOR.

IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED

BY THE MANUFACTURER OR AN AUTHORIZED TECHNICIAN.

THIS APPLIANCE MUST BE GROUNDED. IN CASE OF A MALFUNCTION

OF FAULT, THE GROUND REDUCES THE RISK OF ELECTROCUTION BY

BY PROVIDING THE ELECTRICAL CURRENT WITH AN ALTERNATIVE,

LESS RESISTANT PATH. THIS APPLIANCE IS FITTED WITH A POWER CORD

CONTAINING A GROUND WIRE AND PLUG. FIT THE PLUG INTO A

SUITABLE OUTLET, INSTALLED AND GROUNDED IN COMPLIANCE WITH

LOCAL CODE.

BEFORE MAKING ELECTRICAL CONNECTIONS, DISCONNECT THE

MAIN POWER SUPPLY FROM THE WORK AREA.

CHECK THAT VOLTAGE AND FREQUENCY OF THE OUTLET MATCHES THE

WARNING AN INCORRECTLY CONNECTED GROUND WIRE MAY

GENERATE THE RISK OF ELECTROCUTION. IF IN DOUBT AS TO

THE CORRECT GROUNDING OF THE APPLIANCE, CALL IN A

QUALIFIED ELECTRICIAN OR THE TECHNICAL ASSISTANCE

SERVICE. DO NOT CHANGE THE PLUG ATTACHED TO THE

APPLIANCE.

THE PLUG AT THE END OF THE POWER CORD AND THE CORRESPONDING

OUTLET MUST BE OF THE SAME TYPE AND MUST CONFORM TO LOCAL

REGULATIONS GOVERNING ELECTRICAL APPLIANCES. NEVER REMOVE THE

PLUG BY PULLING ON THE CORD.

LOCATION AND INSTALLATION

(continued)

EN

Clean the front 6” of the underside of the countertop directly above the door.

from steam and condensation when the door of the dishwasher is opened at

the end of the washing cycle.

Apply the steam guard, as shown below. The guard protects the countertop

LOCATION AND INSTALLATION

RECOMMENDED CONDENSATION PROTECTION

MOVE THE DISHWASHER INTO PLACE

11

(continued)

Push the dishwasher into position, taking care not to twist or crush the power

cord or hoses.

TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO PUSH

THE DISHWASHER INTO PLACE.

EN

A

Place the provided template on the inner surface of the overlay panel. Center the template

on the panel and align it with the top edge, matching up the reference locators (A ). . Mark

the position of the door hooks with a pencil. Remove the template and use a drill with a

suitable bit to carefully make holes at the points marked on the panel. Using a Phillips

screwdriver, secure the door hooks with the 8 supplied screws at the marked reference

12

MOUNTING THE OVERLAY DOOR PANEL

(KDW24-OV MODEL)

Drill the holes for the overlay panel handle using a drill with a suitable bit. Attach the

door handle before securing the panel to the dishwasher (screws for mounting the handle

are not provided).

1

2

Attach the door panel by ﬁtting the hooks into their slots on the dishwasher and carefully

slide the panel downwards and securely into place.

points.

Make sure the dishwasher door, complete with panel, opens without restrictions.

LOCATION AND INSTALLATION

(continued)

EN

LOCATION AND INSTALLATION

ATTACHING THE SIDE GASKETS

13

(continued)

Before securing the dishwasher to the adjacent cabinetry, attach the gaskets to

the sides of the dishwasher. Remove the adhesive band on the gasket.

Fix the gasket to the dishwasher, inserting it in the seat on the sides towards

The illustration below shows the proper application of the side gasket.

the front , making sure that the long side of the gasket with the hole for inserting

the screw, is attached to the outside of the dishwasher. The hole in the long side

must match the hole in the dishwasher. Make sure the gasket is properly adhered

rto the dishwasher.

EN

the underside of the countertop. Using the supplied screws, carefully secure the

dishwasher to the cabinetry or countertop then cover the holes with the plugs provided.

After installation, test the dishwasher by starting a work cycle. Check carefully for leaks

and make sure the appliance does not malfunction.

14

COMPLETING THE INSTALLATION

TESTING THE DISHWASHER

It is an important step to properly secure the dishwasher to the adjacent cabinetry or

LOCATION AND INSTALLATION

(continued)

EN

ELECTRICAL CONNECTION, SAFETY AND CAUTION

15

IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISH-

WASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ

ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL.

INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECH-

NICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE.

THIS APPLIANCE IS INTENDED FOR DOMESTIC USE AND SIMI-

LAR APPLICATIONS SUCH AS THE STAFF KITCHENS OF SHOPS,

OFFICES AND OTHER WORKPLACES, INSTITUTIONS, AND FOR

THE USE OF GUESTS AT HOTELS, HOSTELS, BED AND BREAK-

FAST ESTABLISHMENTS AND OTHER RESIDENTIAL FACILITIES

AND COMPLIES WITH DIRECTIVES 2006/95/EC AND 2004/108/

ECCURRENTLY IN FORCE, INCLUDING THE PREVENTION AND

ELIMINATION OF RADIO FREQUENCY INTERFERENCE.

THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PUR-

POSE: WASHING AND DRYING DISHES. ANY OTHER USE

SHALL BE CONSIDERED IMPROPER. THE MANUFACTURER

DECLINES ALL RESPONSIBILITY FOR USES OTHER THAN

THOSE DESCRIBED ABOVE.

BY QUALIFIED AND AUTHORIZED TECHNICIANS.

AS WELL AS INVALIDATING THE WARRANTY, WORK CARRIED

OUT BY UNAUTHORIZED PERSONS MAY GENERATE HAZARDS.

INSTALLATION MUST BE PERFORMED IN COMPLIANCE WITH

ALL THE DIRECTIVES IN FORCE IN THE COUNTRY OF INSTALLA-

TION AND, IF THESE DO NOT EXIST: IN THE UNITED STATES THE

NATIONAL ELECTRIC CODE; IN CANADA THE CANADIAN ELEC-

TRIC CODE C22.1 - LATEST EDITION/PROVINCIAL AND MUNICI-

PAL CODES AND/OR LOCAL CODES.

THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL

NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE IN-

NER EDGE OF THE DOOR. THE NAMEPLATE ON THE INNER

EDGE OF THE DOOR MUST NEVER BE REMOVED.

OR THE LIKE. DISHWASHERS CERTIFIED FOR DOMESTIC

USE ARE NOT SUITABLE FOR COMMERCIAL APPLICATIONS.

THE DOMESTIC MAIN POWER SUPPLY MATCH THE RATINGS

ON THE NAME PLATE OF THE APPLIANCE.

TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED

TO LIFT THE DISHWASHER.

UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS

DO NOT LEAVE DISCARDED PACKAGING MATERIALS

PACKAGING MATERIALS AND TAKE THEM TO THE NEAREST

SORTED WASTE COLLECTION CENTRE. KEEP CHILDREN,

PHYSICALLY AND/OR MENTALLY IMPAIRED ADULTS, AND

ANIMALS AWAY FROM PACKAGING WASTE; DANGER OF

SUFFOCATION.

BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE

MAIN POWER SUPPLY FROM THE WORK AREA.

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE:

INSTALLATION, REPAIRS AND SERVICING MUST BE PERFORMED

THIS APPLIANCE IS NOT SUITABLE FOR USE ON BOATS, CARAVANS

CHECK THAT THE VOLTAGE, FREQUENCY AND PROTECTION OF

EN

DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF

ON THE SHARP EDGES OF THE APPLIANCE; WEAR SAFETY

GLOVES.

CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY

REGULATIONS IN FORCE. IF IN DOUBT, HAVE THE SYSTEM

CHECKED BY A QUALIFIED ELECTRICIAN.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE

TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO

GROUND THE APPLIANCE OR FROM A DEFECTIVE GROUND

CONNECTION.

DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING

TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER. THE APPLIANCE

MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH

THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY

A QUALIFIED TECHNICIAN.

PANELS HAVE BEEN POSITIONED CORRECTLY.

IMMEDIATELY AFTER INSTALLATION, BRIEFLY TEST THE APPLIANCE

FOLLOWING THE INSTRUCTIONS INDICATED BELOW. IF THE

DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT

IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE

NEAREST TECHNICAL SERVICE CENTER. DO NOT ATTEMPT TO

REPAIR THE APPLIANCE.

DO NOT USE EXTENSION CORDS OR ADAPTORS IN ORDER TO AVOID

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

DAMAGE TO PERSONS, ANIMALS OR PROPERTY RESULTING

FROM FAILURE TO OBSERVE THE ABOVE PRECAUTIONS, FROM

TAMPERING WITH EVEN A SINGLE COMPONENT OF THE

APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS.

IF IN DOUBT ABOUT THE CONTENTS OF THIS MANUAL,

CONTACT TECHNICAL SERVICE.

THE POSSIBILITY OF OVERHEATING OR BURNING, WITH THE

CONSEQUENCE OF A FIRE HAZARD.

16

ELECTRICAL CONNECTION, SAFETY AND CAUTION

THE APPLIANCE MUST BE PROVIDE WITH A GROUNDED

DO NOT OPERATE THE DISHWASHER UNLESS ALL OF THE OUTER

EN

FR

DANGER. CECI INDIQUE DES INFORMATIONS ET DES AVERTISSEMENTS QUI,

SI NON OBSERVÉ, PEUT COMPROMETTRE LA SÉCURITÉ PERSONNELLE OU

LES DOMMAGES L'APPAREIL.

DANGER D'ÉLECTROCUTION. CELA INDIQUE DES INFORMATIONS ET

AVERTISSEMENTS DE NATURE ÉLECTRIQUE QUI, S'IL N'EST PAS OBSERVÉ,

PEUT COMPROMETTRE LA SÉCURITÉ PERSONNELLE OU ENDOMMAGER L'APPAREIL.

CE FAITS SAILLANTS RENSEIGNEMENTS GÉNÉRAUX ET MISES EN GARDE

INDIQUE QUE LES DOMMAGES À L'APPAREIL OU LA PROPRIÉTÉ PEUVENT

SURVENIR DU FAIT DE NE PAS OBSERVER CET AVERTISSEMENT.

DÉFINITIONS DE SÉCURITÉ

LISEZ ATTENTIVEMENT ET COMPLÈTEMENT CES INSTRUCTIONS AVANT

D’INSTALLER OU D’UTILISER VOTRE APPAREIL AFIN DE RÉDUIRE LES

RISQUES D’INCENDIE, DE BRÛLURE OU D’AUTRES BLESSURES. CONSERVER

CE MANUEL POUR RÉFÉRENCE FUTURE.

INSTALLATEUR: LAISSER CE MANUEL AVEC LE PROPRIÉTAIRE DE L’APPAREIL.

PROPRIÉTAIRE: CONSERVEZ CE MANUEL POUR RÉFÉRENCE FUTURE.

Ne pas entreposer ou utiliser d’essence ou tout autre liquide ou gaz inﬂammable à proximité

de cet appareil ou de tout autre appareil.

EN PRÉSENCE D’UNE ODEUR DE GAZ:

1. Ne tenter d’allumer aucun appareil.

2. Ne toucher à aucun commutateur électrique.

3. N’utiliser aucun téléphone dans l’immeuble.

4. Appeler immédiatement le fournisseur de gazà partir d’un téléphone situé à l’extérieur

del’immeuble ; Suivre les instructions dufournisseur de gaz.

S’il est impossible de joindre le fournisseur degaz, appeler le service des incendies.

L ’installation et la réparation doivent être effectuées par un installateur ou une agence

deréparation ayant les qualiﬁcations requises oupar le fournisseur de gaz.

LE NON-RESPECT À LA LETTRE DE CES INSTRUCTIONS PEUT CAUSER

UN INCENDIE OU UNE EXPLOSION, QUI POURRAIT ENTRAÎNER DES

DOMMAGES MATÉRIELS, DES BLESSURES OU LA MORT.

TABLE DES MATIÈRES

1 PRÉCAUTIONS DE SÉCURITÉ - AVANT DE COMMENCER

2 NUMÉROS DE MODÈLE

2 ÉTIQUETTE DE NOTATION

2 EXIGENCES RÉGLEMENTAIRES / CODE

3 EMPLACEMENT ET INSTALLATION

12

MONTAGE DU PANNEAU DE PORTE DE RECOUVREMENT

13 FIXATION DES JOINTS LATÉRAUX

14

15 RACCORDEMENTS ÉLECTRIQUES, SÉCURITÉ ET PRÉCAUTIONS

TERMINER L'INSTALLATION ET L'ESSAI

FR

MISE À LA TERRE ÉLECTRIQUE

• Cet appareil doit être mis à la terre. La mise à la terre réduit le risque de choc électrique dans le

événement d'un court-circuit. Lisez la section CONNEXIONS ÉLECTRIQUES de ce manuel

pour des instructions complètes.

• NE PAS broyer sur un tuyau de gaz.

• N'utilisez PAS de rallonge avec cet appareil.

• N'ayez PAS de fusible dans le circuit NEUTRE ou TERRE. Un fusible au NEUTRE

ou le circuit de MISE À LA TERRE pourrait entraîner un choc électrique.

S’il est bien entretenu, cet appariel Hestan procurera un service sûr et ﬁable pendant de nombreuses

années. Lorsqu’on se sert de cet appareil, les pratiques élémentaires suivantes en matière de sécurité

doivent être adoptées.

Conservez ces instructions pour l’utilisation locale de l’Inspecteur du gaz ou des services publics.

Cette cuisinière N’EST PAS conçue pour être installée dans des maisons préfabriquées (mobiles) ou dans

des véhicules récréatifs. N’installez PAS cette cuisinière à l’extérieur.

PRÉCAUTIONS DE SÉCURITÉ - AVANT DE COMMENCER

RISQUE DE CHOC ÉLECTRIQUE

Débranchez l’alimentation avant d’installer ou d’entretenir l’appareil. Avant de le

mettre sous tension, assurez-vous que toutes les commandes sont en position «OFF».

Ne pas le faire peut entraîner la mort ou un choc électrique.

1

La page charge ...

Hestan KDW24 Guide d'installation

Ce manuel convient également à

Hestan KDW24 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents