Monogram ZISP480DKSS Guide d'installation

Catégorie
Frigos
Taper
Guide d'installation
INSTALLATION
INSTRUCTIONS
Side by Side Refrigerators
With Design Guide
Monogram.com
Safety Information
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions for
local inspector’s use. Observe all governing codes and
ordinances.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions with
your Owner’s Manual for future reference.
If you received a damaged unit, you should immediately
contact your dealer or builder.
Skill Level Installation of this unit requires basic
mechanical, carpentry and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the Monogram Warranty. See the Owner’s Manual for
warranty information.
For Monogram local service in your area, call 1.800.444.1845 or visit monogram.com.
For Monogram service in Canada, call 1.800.561.3344
For Monogram Parts and Accessories, call 1.800.444.1845 or visit monogram.com.
WARNING
Tip Over Hazard.
These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping forward
which could result in death or serious injury. Read and follow the entire installation instructions for securing the
appliance with the anti-tip system.
WARNING
Explosion Hazard.
Keep flammable materials and vapors, such as gasoline, away from appliance. Failure to do so can result in fire,
explosion, or death.
WARNING
To reduce the risk associated with choking, do not allow children under 3 years of age to have
access to small parts during the installation of this product.
CAUTION
Lifting Hazard
This refrigerator is very heavy. To reduce the risk of person injury during maneuvering and installing this refrigerator, 3
people are required for proper installation of 36” wide model and 4 people are required for proper installation of a 42”
or 48” wide model.
CAUTION
Keep fingers out of the “pinch point” areas; clearances between the doors and between the doors
and cabinet are necessarily small. Be careful closing doors when children are in the area.
WARNING
Electrical Shock Hazard.
Plug into a grounded 3-prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Immediately discontinue use of a damaged supply cord.
If the supply cord is damaged it must be replaced by a
qualified service professional with an authorized service
part from the manufacturer.
Do not use an extension cord with this appliance.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Follow the instructions in the section Grounding the unit.
This appliance must be installed with a means in the
fixed house wiring or circuit breaker for disconnecting the
appliance from the electrical supply after installation.
31-49171
Consignes de Sécurité
3
AVANT DE COMMENCER
Veuillez lire toutes ces instructions attentivement.
IMPORTANT Conservez ces instructions à
l’usage de l’inspecteur local. Observez tous les codes et
décrets en vigueur.
Note à l’installateur Assurez-vous de laisser ces
instructions au consommateur.
Note au consommateur - Conservez ces instructions
avec votre manuel d’utilisation pour
consultation ultérieure.
Si vous avez reçu un appareil endommagé, veuillez
communiquer immédiatement avec votre revendeur ou votre
entrepreneur.
Niveau de compétence L’installation de cet appareil
exige des compétences de base en mécanique, menuiserie
et plomberie. La responsabilité d’une installation adéquate
relève de l’installateur. La garantie Monogram ne couvre
pas les défectuosités du produit causées par une installation
inadéquate. Consultez le manuel d’utilisation pour des
renseignements sur la garantie.
Pour joindre le service Monogram de votre région, composez le 1.800.444.1845 ou visitez monogram.com.
Pour le service Monogram au Canada, composez le 1.800.561.3344.
Pour le service des Pièces et accessoires Monogram, composez le 1.800.444.1845 ou visitez monogram.com.
AVERTISSEMENT
Risque de basculement.
Ces électroménagers sont lourds du haut, notamment lorsqu’une porte est ouverte, de sorte qu’ils doivent être fixés pour
prévenir un basculement vers l’avant susceptible d’occasionner des blessures graves ou la mort. Lisez et observez la totalité des
instructions d’installation pour connaître la façon de fixer l’électroménager sur le dispositif antibasculement.
AVERTISSEMENT
Risque d’explosion.
Gardez les matières et les vapeurs inflammables telles que l’essence à distance de l’électroménager. L’omission de prendre cette
précaution peut entraîner un incendie, une explosion ou la mort.
AVERTISSEMENT
Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les petites pièces
à la portée des enfants âgés de moins de 3 ans.
ATTENTION
Risque lié à la manipulation d’un objet lourd
Ce réfrigérateur est très lourd. Pour réduire le risque de blessure lors de la manutention de ce réfrigérateur, trois (3) personnes
sont nécessaires pour procéder à l’installation appropriée du modèle 36 pouces, quatre (4) pour l’installation des modèles 42 ou 48
pouces.
ATTENTION
Gardez vos doigts éloignés des points de pincement. Les espaces entre les portes et ceux entre les portes et
l’armoire sont particulièrement restreints. Soyez prudent lorsque vous fermez les portes en présence d’enfants.
AVERTISSEMENT
Risque d’électrocution.
Branchez l’appareil dans une prise à 3 broches mise à la terre.
N’enlevez pas la broche de mise à la terre.
N’utilisez pas un adaptateur.
Cessez immédiatement l’utilisation d’un cordon électrique
endommagé. Si le cordon électrique est endommagé, son
remplacement doit être exécuté par un technicien en réparation
qualifié au moyen d’un cordon de rechange autorisé par le
fabricant.
N’utilisez pas un cordon de rallonge avec cet électroménager.
Le non-respect de ces instructions peut occasionner un décès,
un incendie ou un choc électrique
Suivez les instructions de la section Mise à la terre de l’appareil.
Le circuit électrique auquel cet électroménager sera raccordé
doit comporter un disjoncteur ou un autre dispositif permettant
de couper l’alimentation électrique à l’appareil après l’installation.
31-49171
4
Contents
Safety 2, 3
Instructions for Standard Installation 5-22
Planning Guide
The Installation Space 6
Dimensions and Clearances 6
Customization Basics 7
Side Panels 7
Refrigerator Location 7
1/4” Framed Panel Dimensions 8
3/4” Overlay Panel Dimensions 9
130° Door Swing 10
90° Door Swing 11
Dispenser Trim 12
Installation Instructions
Tools, Hardware, Materials 13
Grounding the Unit 13
Step 1. Remove Packaging 14
Step 2. Move the Refrigerator into the House 14
Step 3. Install Water Line 14
Step 4. Installation with Filtration System 15
Step 5. Install Side Panels 15
Step 6. Anti-Tip Procedures 15
Step 7. Level Refrigerator 16
Step 8. Alternate Anti-Tip Procedure 16
Step 9. Adjust Door Swing 17
Step 10. Install Grille Panel 17
Step 11. Install 1/4” Framed Panels 18
Step 11A. Install Overlay Panels 19, 20
Step 12. Connect Water Supply 20, 21
Step 13. Connect Power, Close Grille Panel 21
Step 14. Start Icemaker 21
Step 15. Install Toekick 21
Inspect Final Installation 22
Instructions for Flush Installation 23-40
Planning Guide
The Installation Space 24
Dimensions and Clearances 24
Customization Basics 25
Custom Handle Design Guide 25
Refrigerator Location 25
Side Panels 25
1/2” Overlay Panel Dimensions 26
3/4” Raised Panel Dimensions 27
3/4” Raised Door Panel Routing 28
3/4” Raised Grille Panel Routing 29
Dispenser Trim 30
Side Cleats 30
Installation Instructions
Tools, Hardware, Materials 31
Grounding the Unit 29
Step 1. Remove Packaging 32
Step 2. Move the Refrigerator into the House 32
Step 3. Install Water Line 32
Step 4. Installation with Water Filtration System 33
Step 5. Install Side Panels 33
Step 6. Install Case Trim 33
Step 7. Anti-Tip Procedure 33-34
Step 8. Level Refrigerator 34
Step 9. Adjust Door Swing 35
Step 10. Install Grille Panel 36
Step 11. Install 1/4” Framed Panels 37
Step 11A. Install Overlay Panels 38
Step 12. Connect Water Supply 39
Step 13. Connect Power, Close Grille Panel 39
Step 14. Start Icemaker 39
Step 15. Install Toekick 40
Inspect Final Installation 40
Instructions for Stainless Steel Installation 41-49
Planning Guide
The Installation Space 42
Dimensions and Clearances 42
Customization Basics 43
Side Panels 43
Refrigerator Location 43
130° Door Swing 44
90° Door Swing 45
Installation Instructions
Tools, Hardware, Materials 46
Grounding the Unit 46
Step 1. Remove Packaging 47
Step 2. Moving the Refrigerator into the House 47
Step 3. Install Water Line 47
Step 4. Installation with Water Filtration System 48
Step 5. Install Side Panels 48
Step 6. Anti-Tip Procedure 48
Step 7. Level Refrigerator 49
Step 8, Alternate Anti-Tip Procedure 49
Step 9. Adjust Door Swing 49
Step 10. Connect Water Supply 50
Step 11. Connect Power, Close Grille Panel 50
Step 12. Start Icemaker 50
Step 13. Install Toekick 51
Inspect Final Installation 51
31-49171
Instructions for Standard Installation
5
31-49171
B
A
Design Guide - Standard Installation
THE INSTALLATION SPACE
Water And Electrical Locations
The opening must be prepared with the electrical and
the cold water supply located as shown.
The Cutout Depth Must Be 24” (60.96 cm)
The refrigerator will project forward, slightly beyond
adjacent cabinetry for standard installation.
Additional Specifications
A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on the rear wall as shown.
The water line can enter the opening through the
floor or back wall. The water line should be 1/4”
O.D. copper tubing or SmartConnect
kit between
the cold water line and water connection location,
long enough to extend to the front of the refrigerator.
Installation of an easily accessible shut-off valve in
the water line is required.
DIMENSIONS AND CLEARANCES
* Shipping height. The
refrigerator can be
adjusted to fit into a
cutout that is 84-1/2”
214.63 cm) in
height. Use leveling
legs and wheels
for a maximum 1”
(2.54 cm) height
adjustment.
Product Clearances
These refrigerators are
equipped with a 3-position
door stop. The factory-
set 115° door swing can
be adjusted to 130°, or
to 90° on panel models
or 90° on stainless steel
models if clearance to
adjacent cabinets or walls
is restricted.
6
90° Door Swing
130° Door Swing
(Panel Models Only)
115° Door Swing
*Finished Width
6"
5"
Electrical
Area
85" max
Finished
Opening
75" From Floor
to Bottom
of Electrical
Area
24"
5"
5"
3 1/2"
Water Supply
3 1/2"
36" Models 12"
42" Models 18"
48" Models 20"
Panel Models Only: Allow minimum clearances for
the freezer door (Dimension A) and fresh food door
(Dimension B) for a full 130° door swing and to allow for
pan removal.
For a 90° door swing, allow 4” (10.16 cm) min.
clearance to a wall. If the 90° door stop position is used,
pan access is maintained, but pan removal is restricted.
See the illustrations on pages 10 and 11 to determine
door swing interaction with adjacent cabinets or
countertops.
Models A B C
36” 13”
(33.02 cm) 15” (38.1 cm) 20-5/8” (52.39 cm)
42” 13” (33.02 cm) 19” (48.26 cm) 26-5/8” (67.63 cm)
48” 15” (38.1 cm) 20” (50.8 cm) 28-5/8” (72.71 cm)
*84"
From
Floor
25-3/8" Framed Models
Depth Including Handles 26-7/8”
36", 42" or 48"
Frame to Frame
35", 41", or 47"
Case Width
*83-1/2"
at
Rear
23-7/8"
Behind
Frame
C
*Min. Distance
to Wall
4”
B
A
*The finished cutout width must be:
35-1/2” (90.17 cm) for 36” models
41-1/2” (105.41 cm) for 42” models
47-1/2” (120.65 cm) for 48” models
31-49171
CUSTOMIZATION BASICS:
These refrigerators are designed to be customized with decorative panels. Field installed custom door and grille
panels are required.
7
Optional Accessory Kits
ZKHSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4” (1.91 cm) overlay panels.
ZKHPSS1: Professional Tubular Stainless Steel
handles designed to fit 3/4” (1.91 cm) overlay panels.
Kit includes one handle. Order 2 kits for side-by-side
refrigerator models from your Monogram supplier
Design Guide - Standard Installation
SIDE PANELS
Side panels must be used
whenever the sides of
the refrigerator will be
exposed. The 1/4”
(0.63 cm) side panels will
slip into the side case trim.
Secure the panels to the
refrigerator with stick-on
hook and loop fastener
strips. Order the side
panels from the cabinet
manufacturer.
Cut a notch in the top
front corner as shown
to allow clearance for
corner keys in the front
side trim.
* Depending on installation height.
*84"
2-9/16"
24"
*3" to 4"
3/16"
1-7/8"
REFRIGERATOR LOCATION
Do not install the refrigerator where the
temperature will go below 55°F (13°C). It
will not run often enough to maintain proper
temperatures.
Do not install the refrigerator where temperatures
will go above 100°F (37°C). It will not perform
properly.
Do not install the refrigerator in a location
exposed to water (rain, etc.) or direct sunlight.
Install it on a floor strong enough to support it
fully loaded.
31-49171
1/4” (0.63 cm) FRAMED PANEL DIMENSIONS
8
If you choose to install framed panels, they must be cut to the
dimensions shown. The panels will slide into the frame on the
door and grille.
Non-Dispenser Models
If the custom panel is less than 1/4” (0.63 cm) thick and it fits
loosely in the door frame it can be backed up with a piece of filler
material or foam tape to improve the fit.
Fresh
Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8
"
Side-by-Side (in inches)
Dispenser Cutout
Position
ABCD E F G
36” Models 33-7/8 9 68-3/8 14-9/16 18-9/16 17-13/16 3-1/8
42” Models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16 17-13/16 3-1/8
48” Models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16 17-13/16 5-1/8
IMPORTANT NOTE: Maximum total panel weight:
Fresh food door panel 75 lbs.(34.0 kg)
Freezer door panel 53 lbs. (24.0 kg)
Grille Panel 18 lbs. (8.16 kg)
1/4"
Panel
Door
5/16"
Trim
Reveal
The framed panel must be 1/4” (0.63 cm) nominal
thickness to fit the dispenser trim.
IMPORTANT NOTE DISPENSER MODELS
The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels.
If the panel is less than 0.250” (0.63 cm) thick, a noticeable gap may be created around the dispenser trim. Foam
tape may be applied on the door to improve the fit.
If the panel is more than 0.250” (0.63 cm) thick, the dispenser trim cannot be secured to the door.
See Dispenser Trim Fit Example, page 12.
Design Guide - Standard Installation
31-49171
36” Side-by-Side (in inches)
Dispenser Cutout
Position
ABCD E F G
1/4” Backer Panel 33-7/8 9 68-3/8 14-9/16 18-9/16
.10” Spacer Panel 33 8-3/8 67 13-1/4 17-1/4
3/4” Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16 17-13/16 3-1/4
42” Side-by-Side (in inches)
ABCD E F G
1/4” Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
.10” Spacer Panel 39 8-5/8 67 13-1/4 23-1/4
3/4” Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16 17-15/16 3-1/4
48” Side-by-Side (in inches)
ABCD E F G
1/4” Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
.10” Spacer Panel 45 8-5/8 67 17-1/4 25-1/4
3/4” Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16 17-15/16 5-1/4
3/4” (1.91 cm) OVERLAY PANEL
DIMENSIONS
For a more custom appearance, overlay panels may
be installed on trimmed models. The overlay panel
must be secured to a 1/4” (0.63 cm) thick backer
panel which slides into the trim. A spacer panel 0.10”
(0.25 cm) thick must be placed between the overlay
and backer panel.
Assemble the panels with glue and screws:
Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws
must be countersunk into the backer panel.
NOTE: Left-to-right offset
is not always equal to top-
to-bottom offset.
9
Spacer Panel
Overlay Panel
Backer Panel
Fresh
Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8
"
*Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled.
IMPORTANT NOTE: Maximum total weight for the
assembled panels:
Fresh food door panel 75 lbs. (34.0 kg)
Freezer door panel 53 lbs. (24.0 kg)
Grille Panel – 18 lbs. (8.16 kg)
IMPORTANT NOTE DISPENSER MODELS
The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels. The
overlay dispenser trim is designed to fit a total panel thickness of 1.100”.
If the panel is less than 1.100” (2.79 cm) a noticeable gap may be created around the dispenser trim.
If the panel is more than 1.100” (2.79 cm) the dispenser trim cannot be secured to the door.
See Dispenser Trim Fit Example, page 12.
The overlay panel must be constructed according to the specifications shown to achieve the correct total
thickness.
Alternative panel construction methods such as securing a 3/4” (1.91 cm) panel to a 1/4” (0.63 cm) backer
panel cannot be used. Another method, routing a 3/4” (1.91 cm) thick panel on all sides, cannot be used.
These methods will not result in the required 1.100” (2.79 cm) panel thickness.
.250” + .10” + .750” = 1.100” Total Panel Thickness
0.63 + 0.25 + 1.91 = 2.79 cm
3/4"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
Design Guide - Standard Installation
31-49171
10
Design Guide - Standard Installation
1/4"
1/2"
3/4"
1"
1-1/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Stainless Steel
1/4"
1/2"
3/4"
2"
1-1/4"
1-1/2"
1-3/4"
3"
2-1/4"
2-1/2"
2-3/4"
1/4"
1/2"
3/4"
Door
23-7/8" From
Rear of
Refrigerator
1"
Refrigerator
Case
Trim
Top View
130° DOOR SWING
Scale 1:1
IMPORTANT NOTE
FOR DISPENSER MODELS:
Dispenser models are supplied with two
dispenser trims, one to fit framed panels
and one for overlay panels. Dispenser
trim fit to the custom panel depends on
correct panel thickness. Framed panels
must be 1/4” (0.63 cm) nominal. Overlay
panels should be constructed as shown
to accomplish a total 1.100” (2.79 cm)
thickness. See pages 19 and 20 for details.
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interfeence with
cabinet door swing. The opening must
allow for filler strips.
31-49171
1/4"
1/2"
3/4"
1"
1-1/4"
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
23-7/8"
From Rear of
Refrigerator
3/4" Overlay
Panel
(Nominal Size)
Case Trim
Refrigerator
Door
Stainless Steel
Top View
90° DOOR SWING
Scale 1:1
IMPORTANT NOTE
FOR DISPENSER MODELS:
Dispenser models are supplied
with two dispenser trims, one
to fit framed panels and one for
overlay panels. Dispenser trim
fit to the custom panel depends
on correct panel thickness.
Framed panels must be 1/4”
(0.63 cm) nominal. Overlay
panels should be constructed
as shown to accomplish a total
1.100” (2.79 cm) thickness
. See
pages 19 and 20 for details.
Frameless Cabinets:
The case trim overlaps
cabinets at the top
and sides. Therefore,
frameless cabinets may
require filler strips to
prevent interference with
cabinet door swing. The
opening must allow for
filler strips.
Design Guide - Standard Installation
11
31-49171
12
DISPENSER TRIM FIT EXAMPLES:
(NOT TO SCALE)
1/4” (0.63 cm) FRAMED
PANEL
The dispenser trim fits over the
custom panel and snaps into the freezer
door.
The clips will not engage the door if
the panel is more than 0.250”
(0.63 cm) thick.
If the panel is less than 0.250”
(0.63 cm) thick, a noticeable gap may
be created around the dispenser trim.
3/4” (1.91 cm) OVERLAY
PANEL
The dispenser trim fits over the
custom panel and snaps into the
freezer door.
The clips will not engage the door if
the panel is more than 1.100” (2.79
cm) thick.
If the panel is less than 1.100” (2.79
cm) thick, a noticeable gap may be
created around the dispenser trim.
Design Guide - Standard Installation
1/4” Dispenser Trim
3/4” Overlay Dispenser Trim
31-49171
13
TOOLS AND MATERIALS REQUIRED
Tinsnips to cut banding
Stepladder
1” Bit extension
Tape measure
Gloves
1/4” Drywall screws
5-Gal. Bucket with cover
6” Spirit level
Appliance hand truck
Tubing cutter
7/16” open-end wrench
#2 Phillips screwdriver
Drill and appropriate bits
5/16”, 7/16” socket
Safety glasses
1-1/8” open end wrench
Pliers
1/4”, 5/16” Combo Rachet
35” long 2x4 for Anti-Tip support
1/4” copper water line tubing or SmartConnect
Refrigerator Tubing kits
Water shut-off valve
Custom panels for doors and grille panel
Screws to secure refrigerator to cabinetry
Stick-on hook and loop fastener strips for 1/4” side
panels
Installation Instructions - Standard Installation
HARDWARE SUPPLIED
Water filter bypass plug
Toekick
1/4” nut and ferrule
Dispenser trim for overlay panels (for use with
Custom Panel models).
GROUNDING THE REFRIGERATOR
WARNING
Electrical Shock Hazard.
Failure to follow these instructions can result in death,
fire, or electrical shock.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall receptacleto minimize the
possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet
is encountered, it is your personal
responsibility and obligation to have
it replaced with a properly grounded
3-prong wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT OR REMOVE THE THIRD
(GROUND) PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
MISE À LA TERRE DU RÉFRIGÉRATEUR
AVERTISSEMENT
Risque de choc
électrique.
Le non-respect de ces instructions peut entraîner des
risques d’incendies, des chocs électriques ou la mort.
Le cordon d’alimentation de cet appareil est équipé
d’une fiche à trois broches (pour une mise à la terre)
qui s’adapte à la prise de courant standard à 3 broches
(pour une mise à la terre) pour minimiser les risques de
chocs électriques par cet appareil.
Faites vérifier la prise murale et le circuit électrique par
un électricien qualifié pour s’assurer que le système est
correctement mis à la terre.
Dans le cas d’une prise biphasée,
l’installateur a la responsabilité et
l’obligation de la remplacer par une prise
triphasée correctement mise à la terre.
NE COUPEZ PAS OU N’ENLEVEZ
PAS, SOUS AUCUN PRÉTEXTE, LA
TROISIÈME BROCHE DE MISE À LA TERRE DU
CORDON D’ALIMENTATION.
N’UTILISEZ PAS D’ADAPTATEUR POUR BRANCHER
LE RÉFRIGÉRATEUR À UNE PRISE BIPHASÉE.
N’UTILISEZ PAS DE RALLONGE AVEC CET
APPAREIL.
FLOORING
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fully loaded refrigerator,
or approximately 1,500 lbs.(680.39 kg).
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under
the refrigerator where you are working.
31-49171
Installation Instructions - Standard Installation
STEP 1 REMOVE PACKAGING
WARNING
Tip Over Hazard.
The refrigerator is much heavier at the top than at the
bottom—be careful when moving. When using a hand
truck, handle from the side only.
AVERTISSEMENT
Risque de
basculement Le réfrigérateur est beaucoup plus
lourd en haut qu’en bas. Il faut être prudent lors des
déplacements. Si un diable est utilisé, il faut soulever
le réfrigérateur sur le côté seulement.
Carefully cut banding at the top and bottom, remove
the outer carton.
Slide out the back corner posts (2).
Slide the carton off the top of the cabinet.
NOTE: IT IS NOT NECESSARY TO LAY THE
CABINET DOWN IN ORDER TO REMOVE THE
SKID!
The unit is secured to the
skid with 4 slotted tie-down
straps. Remove the six
7/16” bolts from the base
channels in the tie-downs.
Remove the six 7/16” bolts
securing the straps to the
skid.
NOTE: DO NOT ATTEMPT
TO ROLL UNIT OFF SKID.
The support blocks on the
bottom of the refrigeration
case must be removed before the refrigerator is
taken off the skid or damage will occur. Carefully
tilt the refrigerator and slide the blocks out from
beneath.
Remove the toekick and set aside for final
installation.
Lift the refrigerator off the skid with an appliance
dolly. Handle from the sides.
STEP 3 INSTALL WATER LINE
WARNING
Connect to potable water supply
only.
AVERTISSEMENT
Raccordez l’appareil à une
alimentation d’eau potable seulement.
A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 p.s.i. (275-827 kPa).
Route 1/4” OD copper or SmartConnect
plastic
tubing between house cold water line and the water
connection location.
The tubing should be long enough to extend to the
front of the refrigerator. Allow enough tubing to
accommodate the bend leading into the water line
connection.
14
Remove
Tie Downs
Toekick
Floor
Cold Water Line
NOTE: The only Monogram approved plastic tubing is
supplied in the SmartConnect
Refrigerator Tubing kits.
Do not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
SmartConnect
Refrigerator Tubing Kits are available
in the following lengths:
2 (.6 m) WX08X10002
8 (2.4 m) WX08X10006
15’ (4.6 m) WX08X10015
25’ (7.6 m) WX08X10025
STEP 2 MOVE THE REFRIGERATOR
INTO THE HOUSE
Re-use the corner posts from the packaging to
protect stainless steel models. Run the appliance
dolly straps over the posts and under the handles.
Leave the protective film on the refrigerator until
installation is complete. IMPORTANT: Never lift the
refrigerator by the handle or push against the grille
panel; this could cause damage or misalignment.
Avoid laying the unit on its back or side to prevent
sealed system restrictions.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off the water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in
many water supply kits. Before purchasing, make sure
a saddle type valve complies with your local plumbing
codes.
31-49171
15
STEP 4 INSTALLATION WITH
HOUSEHOLD WATER
FILTRATION SYSTEM
Skip this step if you do not have a household
water filtration system
If the water supply to the refrigerator is from any
household water filtration system, the filter cartridge
should be removed. For better ice and water
performance, remove the filter and install the filter
bypass plug.
STEP 5 INSTALL SIDE PANELS
Skip this step when not using side panels.
If you are using 1/4” (0.63 cm) side panels, they
should be inserted into the case trim. Fasten the
panels to the refrigerator with stick-on hook and loop
fastener strips before setting the refrigerator in place.
STEP 6
ANTI-TIP PROCEDURE
WARNING
Tip Over Hazard.
These refrigerators are top heavy, especially with
any doors open, and must be secured to prevent
tipping forward which could result in death or
serious injury. Read and follow the entire installation
instructions for securing the refrigerator with the anti-
tip system.
AVERTISSEMENT
Risque de
basculement
Ces réfrigérateurs présentent une partie supérieure
lourde, en particulier avec une porte ouverte; ils
doivent donc être fixés pour prévenir le basculement
vers l’avant et le risque concomitant de blessure
grave ou fatale. Lisez et suivez les instructions
d’installation complètes pour l’installation du système
anti-basculement.
Installation Instructions - Standard Installation
Filter Bypass
Plug
Rotate Counterclockwise
to Remove
Cut a 2” x 4” block, 35” (88.9 cm) long and secure
the block to the mounting brackets provided using
#12 or #14 wood screws.
Secure the
bracket with
wood block to
the back wall
so that it is 84”
(213.36 cm)
from the finished
floor. Use #12
or #14 wood
screws. See the
illustration.
The screws must
penetrate at least one inch into the vertical wall
studs.
If metal wall studs, use self-tapping sheet metal
screws in place of wood screws.
IMPORTANT: When the refrigerator is installed under
a soffit or if there is not enough height for this method
of security, brackets cannot be used. Proceed to step
7 to level the refrigerator and then to step 8 to secure
refrigerator to cabinets.
The refrigerator must be
secured to prevent tipping.
Connect Power Cord:
Before pushing the refrigerator into the opening,
plug the power cord into the receptacle. The water
filter guard will need to be removed for access
(some models). Remove the 3 screws holding it
in place. If access is still too tight, remove the 2
screws holding the water filter bracket and move
aside. Open the grille panel and reach into the
opening at the back to grasp the power cord. Pull
the power cord into the opening as you push the
refrigerator back. Secure the bracket and guard with
the original screws.
Gently push refrigerator into the opening with hands
against front corners.
STEP 6 ANIT-TIP PROCEDURE (Cont.)
31-49171
16
STEP 7 LEVEL REFRIGERATOR
All models have 4-point leveling. The front is
supported by leveling legs, the rear is supported by
adjustable wheels. Both are accessible from the front
of the refrigerator.
To level the back of the refrigerator, turn the 7/16”
hex nut located above the front wheels. Turn
clockwise to raise or counterclockwise to lower the
refrigerator.
For front leveling, use a
1-1/4” open-end wrench.
Adjust height of refrigerator
to match installation cutout
opening 84-1/2”
(214.63 cm). The refrigerator
should be level and plumb
with cabinetry.
NOTICE: The rear leveling wheels and front leveling
legs are limited to a maximum height adjustment of
1” (2.54 cm). If the installation requires more than
84-1/2” (214.63 cm) height, the installer should
elevate the refrigerator on a sheet of plywood or
runners. Cabinetry trim could also be added across
the top of the opening to shorten the opening. If you
attempt to raise the refrigerator more than 1”
(2.54 cm), you will damage the front leveling legs
and the rear leveling wheels. Make adjustments in
small increments.
Installation Instructions - Standard Installation
STEP 8 ALTERNATE ANTI-TIP
PROCEDURE
The refrigerator must be secured to prevent tipping.
Raise the grille panel to access case trim.
Use a 3/16” bit to drill four evenly spaced clearance
holes through the metal top case trim.
Use a 1/16” bit to drill to pilot holes through the metal
clearance holes and into the wood soffit. The holes
should be centered in the soffit or a 3/4” (1.91 cm)
min. wood brace. The brace spanning the enclosure
must be securely fastened to cabinets on both sides.
Install four, 1-1/2” drywall screws into the pilot holes.
Drill screws into adjacent cabinets through side case
trim.
31-49171
Installation Instructions - Standard Installation
STEP 9 ADJUST DOOR SWING
NOTE: This refrigerator has a 3-position door stop:
90°, 115°, and 130°. When space does not allow the
door to swing open fully to 115°, you may change
the door swing to a 90° opening. A 130° door swing
option is available for standard installation only. Skip
this step if door opening is satisfactory for your
installation situation.
Open the door to view the bottom hinge. Note the
door stop pin locations. The pin is factory installed in
the 115° position.
Close the door. From below, use pliers to unscrew
the door stop and reinstall into the 130° or 90°
position.
STEP 10 INSTALL GRILLE PANEL
To insert the framed or overlay panel into the
grille:
Raise the grille panel to the stop position.
Adjust Nut Below
Spring to Accommodate
Panel Weight
Loosen
Side
Trim
Screw
Loosen
Side
Trim
Screw
Loosen the screws on the side trim behind the frame.
Remove the bottom trim.
CAUTION
SHARP EDGE HAZARD
The metal panel may be slippery. Grip the metal
panel firmly so the panel does not slip out of the
frame and cause personal injury or damage to the
frame.
ATTENTION
RISQUE DE COUPURE :
ATTENTION AUX ARÊTES VIVES
Le panneau en métal peut bêtre glissant. Tenir
fermement le panneau en métal, de manière à ce
que le panneau ne glisse pas en dehors du cadre
en provoquant des blessures corporelles ou des
dommages au cadre.
Slide the panel over the metal backer panel and into
the trim.
If necessary, tap with a wood block until the panel
slips under the top trim piece.
Reassemble the bottom trim. Tighten the screws.
Adjust the hinge spring to accommodate the panel
weight, if necessary.
17
31-49171
STEP 11 INSTALL 1/4” (0.63 cm) FRAMED PANELS
Install door panels:
Open the door to 90°. Remove the 6 Phillips head
screws from the door handle.
Remove the handle. Retain all screws.
Remove the 6 screws holding the trim, then lift off the
trim. Retain the screws.
Slide the framed panel into the door trim.
Dispenser Models Only:
The dispenser controls protrude beyond the face of the
freezer door. To avoid damage to the dispenser, the
trim at the top of the door should be removed.
Remove the screws holding the top trim in place.
Place the freezer panel into the bottom channel and
slide into the hinge side trim.
Reinstall the top trim piece with screws.
There are two sets of holes in the handle side trim.
Replace the handle side trim by installing the original
screws in the FRONT screw holes.
Secure the handle to the door using the REAR screw
holes.
Follow the same procedures to install the opposite
panel.
Check to be sure the handles are evenly aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
NOTE: Aluminum cover trim is supplied for use with
custom handles on overlay panels. It is not intended for
use with 1/4” (0.63 cm) panels. Discard the cover trim
when using 1/4” (0.63 cm) framed panels.
Go to Step 12A for Overlay Panels
Supplied Handle
Shown in 1/4”
Panel Position
18
Installation Instructions - Standard Installation
31-49171
STEP 11A INSTALL OVERLAY PANELS
Install door panels:
Open door to 90°. Remove the 6 Phillips head screws
from the door handle.
Remove the handle. Retain all screws.
Remove the 6 screws holding the trim, then lift off the
trim. Retain the screws.
Slide the overlay panel into the door trim.
Dispenser Models Only:
The dispenser controls protrude beyond the face of
the freezer door. To avoid damage to the dispenser,
the trim at the top of the door should be removed.
Remove the screws holding the top trim in place.
Place the assembled freezer panel into the bottom
channel and slide into the hinge side trim.
Reinstall the top trim piece with the screws.
There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the REAR screw holes.
Secure the handle to the door using the FRONT
screw holes.
Follow the same procedures to install the opposite
panel.
Check to be sure the handles are evenly aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
Supplied Handle
Shown in Overlay
Panel Position
Installation Instructions - Standard Installation
19
31-49171
STEP 12 CONNECT WATER SUPPLY
Locate and bring the tubing to the front of the
cabinet.
Turn the water on to flush debris from the line. Run
about a quart of water through the tubing into a
bucket, then shut off the water.
Copper Tubing:
Slip a 1/4” nut and ferrule (provided) over both ends
of the copper tubing. Insert the tube into the union
fitting on the unit and tighten the nut to the union.
Turn on the water to check for leaks.
SmartConnect
Tubing:
NOTE: The only Monogram-approved plastic tubing
is supplied in the SmartConnect
Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Other
types of plastic may crack or rupture with age and
cause water damage to your home.
Refrigerator
Water Supply
House
Water Supply
20
Installation Instructions - Standard Installation
STEP 11A INSTALL OVERLAY PANELS
(continued)
Custom Handles
If you are using custom handles, the handle must e
properly secured to the overlay panel before sliding
the panel into the trim.
The cabinet manufacturer will supply the custom
handle and hardware.
Discard the supplied handle.
Remove the trim. Peel away a few inches of the
adhesive backing.
IMPORTANT: The tape is very sticky and strong.
Once it adheres to a surface, it cannot be removed
without damaging both surfaces. Do not install the
trim before the final wood panels are in place. Be
sure to align the trim carefully before removing the
paper backing.
Reinstall the handle side trim, using all 12 supplied
flat-head screws, plus the 12 flat-head screws
originally installed in the handle trim.
Install a supplied end cap onto the top of the door,
using a Phillips head screwdriver and the 2 screws
provided. Hand-tighten the screws into the end
caps. Do not overtighten; damage will occur.
Clean the aluminum trim with rubbing alcohol—
do not use alcohols with oil or lanolin that will prevent
adhesion of double-sided tape.
Slip the aluminum cover onto the top bracket to check
the fit. The aluminum cover trim has a slot on each
end which fits the bracket.
Reinstall all original screws.
STEP 11A INSTALL OVERLAY
PANELS (continued)
Carefully place the aluminum cover trim onto the top
bracket so that the bracket is inside the cover trim.
Use the top to bottom grooves along the handle side
to align the cover trim accurately. Align the bracket
with the screw holes in the top of the door. Pull the
tape a few inches at a time while pressing the trim
against the door. Press and hold approximately 10
seconds before continuing along the length of the
door.
Install another bracket at the bottom of the door to
secure the cover trim. Use a stubby Phillips head
screwdriver and the 2 screws provided.
NOTE: Make sure there are no gaps in the
installation.
Follow the same procedure on the opposite door.
Secure top
bracket with
2 screws.
Top Bracket
Top Bracket
Slide aliminum
trim over top
bracket.
31-49171
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Monogram ZISP480DKSS Guide d'installation

Catégorie
Frigos
Taper
Guide d'installation

dans d''autres langues