Samsung CHW9060AW Le manuel du propriétaire

Marque: Samsung

Modèle: CHW9060AW

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

CHW9150GW

INSTALLATION INSTRUCTIONS

COMMERCIAL FRONT-LOAD WASHER

INSTRUCTIONS D’INSTALLATION

LAVEUSE COMMERCIALE À CHARGEMENT FRONTAL

Table of Contents/Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

W10726004B

www.whirlpoolcommerciallaundry.com

TABLE OF CONTENTS

WASHER SAFETY ................................................................................... 3

INSTALLATION REQUIREMENTS ..........................................................4

Tools and Parts .....................................................................................4

Accessories .......................................................................................... 4

Options .................................................................................................4

Location Requirements ........................................................................5

Drain System ........................................................................................ 5

Electrical Requirements........................................................................6

INSTALLATION INSTRUCTIONS ............................................................6

Remove Transport System ................................................................... 6

Connect the Inlet Hoses .......................................................................7

Connect the Drain Hose ....................................................................... 8

Secure the Drain Hose .........................................................................8

Level the Washer .................................................................................. 9

Complete Installation............................................................................9

USER & SET-UP INSTRUCTIONS ........................................................ 10

General User Information ...................................................................10

Control Set-up Procedures ................................................................10

Start Operating Set-up ....................................................................... 11

WASHER CARE .....................................................................................13

Cleaning Your Washer ........................................................................ 13

Water Inlet Hoses ............................................................................... 13

ASSISTANCE OR SERVICE .................................................................. 13

WARRANTY ........................................................................................... 14

TABLE DES MATIÈRES

SÉCURITÉ DE LA LAVEUSE ................................................................15

EXIGENCES D’INSTALLATION ............................................................16

Outillage et pièces ..............................................................................16

Accessoires ........................................................................................16

Options ...............................................................................................17

Exigences d’emplacement ................................................................. 17

Système de vidange ...........................................................................18

Spéciﬁcations électriques ..................................................................18

INSTRUCTIONS D’INSTALLATION ...................................................... 19

Dépose du système de transport ....................................................... 19

Raccordement des tuyaux d’alimentation..........................................20

Raccordement du tuyau de vidange ..................................................21

Immobilisation du tuyau de vidange ..................................................21

Réglage de l’aplomb de la laveuse ....................................................22

Achever l’installation ..........................................................................22

INSTRUCTIONS D’UTILISATION ET D’INSTALLATION .....................23

Informations générales ....................................................................... 23

Procédures de réglage des systèmes de commande ........................ 23

Paramétrage pour mise en marche .................................................... 24

ENTRETIEN DE LA LAVEUSE ..............................................................26

Nettoyage de la laveuse .................................................................... 26

Tuyaux d’arrivée d’eau .......................................................................27

ASSISTANCE OU SERVICE .................................................................. 27

GARANTIE ............................................................................................. 27

WASHER SAFETY

Alternate Parts

Your installation may require additional parts. If you are interested

in purchasing one of the items listed here, call the toll-free number

in the “Assistance or Service” section.

If you have You will need to buy

Laundry tub or standpipe

taller than 96" (2.4 m)

Sump pump system (if not already

available)

Overhead sewer Standard 20 gal. (76 L), 30"

(762 mm) tall drain tub or utility sink

and sump pump (available from

local plumbing suppliers)

Floor drain Siphon break, Part Number 285834;

additional drain hose,

Part Number 8318155; and

connector kit, Part Number 285835

Drain hose too short 4 ft (1.2 m) drain hose extension kit,

Part Number 285863

Water faucets beyond

reach of ﬁll hoses

2 longer water ﬁll hoses:

6 ft (1.8 m) Part Number 76314

10 ft (3.0 m) Part Number 350008

Accessories

Enhance your washer with these premium accessories.

For more high-quality items or to order, call 1-800-901-2042,

or visit us at www.whirlpool.com/accessories. In Canada call:

1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Part Number Accessory

8212526

Washer drip trays, ﬁts under all

31682

All purpose appliance cleaner

1903WH

Laundry supply storage cart

Options

Pedestal

You have the option of purchasing pedestals separately for this

washer. The pedestal will add to the total height of the washer.

Optional pedestal

Pedestal

Height

Approximate

height with washer

Color

Part Number

⁄8" (73 mm) *47.5" (1207 mm) White WHP0400VW

*Add

⁄8" (16 mm) minimum for leveling feet.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses:

■ Pliers (that open to

⁄16" [39.5 mm])

■ Flashlight (optional)

Tools needed for installation:

■ Open end wrenches

½" and

⁄16"

■ Torx T-20

®†

Security

screwdriver

■ ¼" Nut driver

■ Level

■ Wood block

■ Ruler or measuring tape

A. U-shaped hose form

B. Water inlet hoses (2)

C. Inlet hose washers (4)

D. Transit bolt hole plug (4)

E. Beaded tie strap

A B

Parts supplied:

®† TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Door is not reversible

/16"

(732 mm)

/8"

(1134 mm)

27"

(686 mm)

50 ½"

(1282 mm)

Washer Dimensions

A ﬂoor drain should be provided under the bulkhead. Prefabricated

bulkheads with electrical outlets, water inlet lines, and drain facilities

should be used only where local codes permit.

Drain System

The washer can be installed using the standpipe drain system

(ﬂoor or wall), the laundry tub drain system, or the ﬂoor drain

system. Select the drain hose installation method you need.

See “Tools and Parts.”

Standpipe drain system – wall or ﬂoor (views A & B)

The standpipe drain requires a minimum diameter standpipe

of 2" (50 mm). The minimum carry-away capacity can be no less

than 12 gal. (45.5 L) per minute, per washer.

The top of the standpipe must be at least 30" (762 mm) high

and no higher than 96" (2.4 m) from the bottom of the washer.

30" min.

(762 mm)

A B

Laundry tub drain system

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 30" (762 mm) above the ﬂoor.

Location Requirements

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer “walk.”

Your washer can be installed under a custom counter, or in a

basement, laundry room, or recessed area. See “Drain System.”

Companion appliance location requirements should also be

considered. Proper installation is your responsibility.

You will need:

■ A water heater set to deliver 120°F (49°C) water to the washer.

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the washer.

See “Electrical Requirements.”

■ Hot and cold water taps located within 4 ft. (1.2 m) of the hot

and cold water ﬁll valves, and water pressure of 20–100 psi

(137.9–689.6 kPa).

■ A level ﬂoor with a maximum slope of 1" (25 mm) under entire

washer. Installing the washer on soft ﬂoor surfaces, such as

carpets or surfaces with foam backing, is not recommended.

■ A sturdy and solid ﬂoor to support the washer with a total

weight (water and load) of 400 lbs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C).

Some water can remain in the washer and can cause damage

in low temperatures.

Installation clearances

■ The location must be large enough to allow the washer door

to be fully opened.

■ Additional spacing should be considered for ease of

installation and servicing. The door opens more than 90°,

and it is not reversible.

■ Additional clearances might be required for wall, door,

and ﬂoor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the washer

is recommended to reduce noise transfer.

■ Companion appliance spacing should also be considered.

30" min.

(762 mm)

*Height without leveling feet installed.

Shipping bolt with plastic spacer

INSTALLATION

INSTRUCTIONS

Remove Transport System

IMPORTANT: Position the washer so that the rear of the washer

is within approximately 3 ft. (900 mm) of its ﬁnal location.

There are 4 shipping bolts in the rear panel of the washer that

support the suspension system during transportation. These bolts

also retain the power cord inside the washer until the bolts are

removed.

1. Keep the washer in the upright position while removing the

shipping bolts.

Shipping bolt

Back view

Floor drain system

The ﬂoor drain system requires a siphon break that may be

purchased separately. See “Tools and Parts.”

The siphon break must be a minimum of 28" (710 mm) from

the bottom of the washer. Additional hoses might be needed.

Electrical Requirements

■ A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is recommended that a separate circuit

serving only this washer be provided.

■ This washer is equipped with a power supply cord having

a 3 prong grounding plug.

■ To minimize possible shock hazard, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

If a mating outlet is not available, it is the personal

responsibility and obligation of the customer to have the

properly grounded outlet installed by a qualiﬁed electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate.

■ Do not ground to a gas pipe.

■ Check with a qualiﬁed electrician if you are not sure

the washer is properly grounded.

■ Do not have a fuse in the neutral or ground circuit.

28" min.

(710 mm)

2. Using a ½" wrench, loosen each of the bolts.

3. Once the bolt is loose, move it to the center of the hole

and completely pull out the bolt, including the plastic spacer

covering the bolt.

4. Once all 4 bolts are removed, discard the bolts and spacers.

Then push the power cord plug into the opening on the right

side of the rear panel and pull the power cord through the

opening on the left side of the rear panel and close holes with

the attached cap. Do not pull plug end of power cord through

the right side hole.

5. Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your

product distributor or installer. To avoid suspension and structural

damage, your washer must be properly set up for relocation

by a trained professional.

Connect the Inlet Hoses

Insert new ﬂat washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

A B

A. Coupling

B. Washer

Connect the inlet hoses to water faucets

Make sure the washer drum is empty.

1. Attach a hose to the hot water faucet. Screw on coupling

by hand until it is seated on the washer.

2. Attach a hose to the cold water faucet. Screw on coupling

by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten, use tape, or sealants on the valve.

Damage to the valves can result.

Clear water lines

■ Run water through both faucets and inlet hoses, into a

laundry tub, drainpipe, or bucket, to get rid of particles in the

water lines that might clog the inlet valve screens.

■ Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

C. Cold water inlet

H. Hot water inlet

1. Attach the hot water hose to the check valve on washer’s

hot (H) water inlet valve. Screw on coupling by hand until

it is seated on the check valve.

2. Attach the cold water hose to the check valve on washer’s

cold (C) water inlet valve. Screw on coupling by hand until

it is seated on the check valve.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

4. Turn on the water faucets completely and check for leaks and

at washer connection.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement dates

on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Connect the Drain Hose

Remove drain hose from washer drum

1. Use locking pliers, squeeze hose clamp tabs together

and insert over the end of drain hose.

2. Slide drain hose onto washer connection.

3. Once drain hose is in place, release pliers.

Washer drain system can be installed using a ﬂoor drain,

wall standpipe, ﬂoor standpipe, or laundry tub.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose.

To keep drain water from going back into the washer:

■ Use the drain hose form, and do not force excess drain hose

into standpipe. Hose should be secure, but loose enough

to provide a gap for air.

■ Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See Floor drain under

“Tools and Parts.”

Secure the Drain Hose

Drain hose must be secured to stop the hose from moving when

water is pumped out. If the drain hose moves, water may end up

on the ﬂoor.

1. Drape the power cord over the washer top.

2. Move the washer to its ﬁnal location.

3. Place the drain hose in the laundry tub or standpipe as shown.

See illustrations A and B.

A B C

NOTES:

■ Do not force excess drain hose back into the rear of

the washer.

■ To avoid siphoning, do not seal or put more than 4½"

(114 mm) of the drain hose into drainpipe or standpipe.

■ If the washer faucets and the drain standpipe are recessed,

put the hooked end of the drain hose in the standpipe as

shown. See illustration C.

114 mm

/2")

114 mm

/2")

114 mm

/2")

4½"

(114 mm)

4½"

(114 mm)

4½"

(114 mm)

Level the Washer

Properly leveling your washer avoids excessive noise

and vibration.

1. Check the levelness of the washer by placing a level on the

top edge of the washer, ﬁrst side to side, then front to back.

If the washer is against a wall, move the washer out slightly

before tipping back. If the washer is not level, ﬁrst prop the

front with a wood block and adjust the feet as necessary; then

prop the back and adjust feet as necessary. Repeat this step

until washer is level.

2. Make sure all four feet are stable and resting on the ﬂoor.

Then check that the washer is perfectly level (use a level).

3. After the washer is level, use a 9/16" open-end wrench to turn

the nuts on the feet tightly against the washer cabinet.

IMPORTANT: All four feet must be tightened. If the nuts are

not tight against the washer cabinet, the washer may vibrate.

4. The washer should not move front to back, side to side,

or diagonally when pushed on its top edges.

5. Slide the washer to its ﬁnal location.

6. Conﬁrm the levelness of the washer.

Complete Installation

1. Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding

method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

7. Plug into an grounded 3 prong outlet.

8. To test and to clean your washer, measure ½ the detergent

manufacturer’s recommended amount of High Efﬁciency (HE)

detergent for a medium-size load. Pour the detergent into

the detergent dispenser. Select any cycle and allow the

washer to complete one whole cycle.

NOTE: After the washer has been installed and plugged in, the

display may show ‘0 MINUTES’. Once the washer has been

plugged in and the washer door opened and closed, the display

will show the price. In washers set for free cycles, the display will

ﬂash ‘SELECT CYCLE’.

1. Insert coins until ‘SELECT CYCLE’ ﬂashes in display.

2. Door must be closed before cycle selection is made,

3. Press fabric setting button for the wash cycle desired. After

the cycle is started, the time will display and count down.

4. If a cycle is interrupted by opening the door, ‘RESELECT

CYCLE’ will ﬂash in the display. To restart the washer, close

door, and reselect desired cycle.

General User Information

SCROLLING ‘OUT OF ORDER’ SHOWING IN DISPLAY

This condition indicates the washer is inoperative.

‘0 MINUTES’ SHOWING IN DISPLAY

This indicates the cycle is complete and the washer cannot be

operated. Coins dropped or debit inputs during this condition will

be stored in escrow but cannot be used until normal operation is

restored by opening and closing the door. If a door switch fails, it

must be replaced before normal operation can be restored.

COLD START (Initial ﬁrst use)

Washer is programmed at the factory as follows:

11-minute wash period

3 rinses (extra rinse not enabled)

$2.00 wash price (9050 model)

$0 wash price (9060 model)

WARM START (after power failure)

A few seconds after power is restored, if a cycle was in progress at

the time of the power failure, ‘RESELECT CYCLE’ will ﬂash in the

display, indicating the need for a key press to restart the washer.

DOOR LOCK

Prior to beginning a cycle, there is a door lock routine of lock/

unlock/relock; then cycle begins. The door will remain locked

until the end of a cycle or approximately 2 minutes after a

power interruption.

PRICING

After the door is opened following the completion of a cycle, the

display indicates the cycle price (unless set for free operation). As

coins are dropped or debit inputs arrive, the display will change to

lead the user through the initiation of a cycle.

FREE CYCLES

This is established by setting the cycle price to zero. When this

happens, ‘SELECT CYCLE’ will appear rather than a cycle price.

DEBIT CARD READY

This washer is debit card ‘cable’ ready. It will accept a variety of

debit card systems, but does NOT come with a debit card reader.

Refer to the debit card reader manufacturer for proper washer

set-up. In models converted to a Generation 1 debit card system,

debit pulses represent the equivalent of one coin (coin 1).

Control Set-up Procedures

IMPORTANT: Read all instructions before operating.

9050 Models: Insert access door key, turn, and lift to remove

access door.

9060 Models: Once the debit card reader is installed (according

to the reader manufacturer’s instructions), the set-up mode can

only be entered by inserting a set-up card (supplied by the reader

manufacturer) into the card slot. If a set-up card is not available,

diagnostic modes can be entered by removing connector AA1 on

the circuit board or by using the Service Access Code (see Service

Access Code section, page 12) for 9060 models.

IMPORTANT: Unplug washer or disconnect power before opening

the console. To access connector AA1:

1. Unplug washer or disconnect power.

2. Open console, disconnect plug on AA1, close console.

3. Plug in washer or reconnect power.

The washer is now in the set-up mode. The lower 3 buttons and

the digital display are used to set up the controls. The display

can contain 4 numbers and/or letters and a decimal point. These

are used to indicate the set-up codes and related code values

available for use in programming the washer.

Once the washer has been programmed with a Gen 2 card reader

installed, the washer will be in dAS mode permanently, and dAS

will be displayed every time set-up mode is accessed.

The lower fabric setting buttons and the digital display are used to

set up the controls.

The display can contain 4 numbers and/or letters and a decimal

point. These are used to indicate the set-up codes and related

code values available for use in programming the washer.

HOW TO USE THE BUTTONS TO PROGRAM THE CONTROLS

1. The HOT button is used to adjust the values associated with

set-up codes. Pressing the button will change the value by

increments. Rapid adjustment is possible by holding down

the button.

2. The WARM button will advance through the set-up codes.

Pressing the button will advance to the next available set-up

code. Holding the button down will automatically advance

through the set-up codes at a rate of 1 per second.

3. The COLD button is used to select or deselect options.

USER & SETUP INSTRUCTIONS

Start Operating Set-up

Before proceeding, it is worth noting that, despite all of the

options available, an owner can simply choose to uncrate a new

commercial washer, hook it up, plug it in, and have a washer

that operates.

Washers are preset at the factory for an 11-minute wash period

and 3 rinses (no extra rinse).

SET-UP CODES

■ The

WARM

button will advance you from code to code.

■ The

HOT

button will change the code value.

■ The

COLD

button will select or deselect options.

The set-up code is indicated by the one or two left-hand

characters. The set-up code value is indicated by the two

or three right-hand characters.

NOTE: The ﬁrst line of each code indicates the factory default

for 9050 models.

CODE EXPLANATION

6 01

REGULAR CYCLE PRICE (Factory Default)

6 01 When the d.xx is set to d.CS, this 6 xx value

represents the number of push-in actuations of the

coin slide to start the washer. 6 01 would equal one

coin slide activation.

When the d.xx is set to d.00, this 6 xx value

represents the number of coins needed to start the

washer; may adjust from 0–39. Change this value

by pressing the HOT button. 6 07 = 7 coins. 9060

models default to 6 00.

Press the

WARM

button once to advance

to next code.

8 00

ADDITIONAL RINSE OPTION

This option is either SELECTED ‘ON’ or NOT

SELECTED ‘OFF’.

Not Selected ‘OFF’.

Selected ‘ON’.

Press the

COLD

button once for this selection.

Press the

WARM

button once to advance

to next code.

9 00

CYCLE COUNTER OPTION

This option is either SELECTED ‘ON’ or NOT

SELECTED ‘OFF’.

Not Selected ‘OFF’.

Selected ‘ON’ and not able to be deselected.

Press the

COLD

button 3 consecutive times to select

‘ON’. Once selected ‘ON’ it cannot be deselected.

Press the

WARM

button once to advance

to next code.

CODE EXPLANATION

1. 00

MONEY COUNTER OPTION

This option is either SELECTED ‘ON’ or NOT

SELECTED ‘OFF’.

Not Selected ‘OFF’.

Selected ‘ON’.

Press the

COLD

button 3 consecutive times to

select ‘ON’ and 3 consecutive times to remove

(Not Selected ‘OFF’.) Counter resets by going

from ‘OFF’ to ‘ON’.

Selected ‘ON’ and not able to be deselected.

To select ‘ON’ and not able to be deselected,

ﬁrst select ‘ON’, then within 2 seconds, press

the

COLD

twice,

HOT

once, and exit the set-up

mode.

Press the

WARM

button

once to advance

to next code.

2. 00 This option is not available.

b. 40

VALUE OF COIN 1

b. 05

This represents the value of coin 1 in number

of nickels: 05 = $0.25.

By pressing the

HOT

button, there is an option

of 1–199 nickels.

With coin slide activation, this represents the total

vend price in nickels. Example: b.40 is equal to

$2.00.

Press the

WARM

button once to advance

to next code.

C. 20

VALUE OF COIN 2

This represents the value of coin 2 in number

of nickels: 20 = $1.00.

By pressing the

HOT

button, there is the option

of 1–199 nickels.

Press the

WARM

button once to advance

to next code.

d. CS

COIN SLIDE OPTION

This option is either SELECTED ‘ON’ or NOT

SELECTED ‘OFF’. Press the COLD button 3

consecutive times to select/deselect this option.

Selected ‘ON’. (Default for 9050 models)

When coin slide mode is selected, set ‘b’. equal to

value of vend price in nickels. Set set-up code 6 xx

(regular cycle price) to number of slide operations. If

the installer sets-up ‘CS’ and a coin drop mechanism

is installed, the washer will not

Not Selected ‘OFF’. (Default for 9060 models)

Press the

WARM

button once to advance

to next code.

1 00 Represents the number

of cycles in HUNDREDS

1 02 = 200

2 00 Represents the number

of cycles in ONES

2 25 = 25

TOTAL CYCLES = 225

3 00 Number of dollars

in HUNDREDS

3 01 = $100.00

4 00 Number of dollars in ONES 4 68 = $ 68.00

5 00 Number of CENTS 5 75 = $ .75

TOTAL = $168.75

CODE EXPLANATION

J. Cd

COIN/DEBIT OPTION

Both coin and debit selected. Press the

COLD

button

3 consecutive times for this selection. (Default for

9050 models)

Coins selected, debit disabled. Press the

COLD

button 3 consecutive times for this selection.

Debit card selected, coins disabled. Press the COLD

button 3 consecutive times for this selection. (Default

for 9060 models)

Enhanced Debit is self-selected when a Generation 2

card reader is installed in the washer. The Ed option

cannot be manually selected or deselected.

Press the

WARM

button once to advance

to next code.

n. CE

CLEAR ESCROW OPTION

When selected, money held in escrow for

30 minutes without further escrow or cycle

activity will be cleared.

Not Selected ‘OFF’.

Selected ‘ON’. Press the

COLD

button once for

this selection.

Press the

WARM

button once to advance to

next code.

A1.

PREWASH LENGTH

A1.

This is the number of minutes of PREWASH. Choose

0 to disable the prewash or select between 2 and 7

minutes by pressing the

HOT

button.

Press the

WARM

button once to advance

to next code.

If cycle counter (9 0C) is selected, the following is true:

This is “VIEW ONLY” and cannot be cleared.

Press the

WARM

button once to advance to next code.

If money counter (1.0C or 1.C0) is selected, the following

is true:

END OF SET-UP PROCEDURES

EXIT FROM SET-UP MODE

CHW9050 Models:

Reinstall access door.

CHW9060 Models:

1. Unplug washer or disconnect power.

2. Open console, reinsert plug into AA1, close console.

3. Plug in washer or reconnect power.

MODEL CHW9050 SET UP AS PN WITH PROGRAMMING

SWITCH:

Turn key clockwise and remove.

MODEL CHW9060 SET UP AS PN WITHOUT PROGRAMMING

SWITCH:

Set-up mode can be exited by using procedures from “Service

Access Code.”

SERVICE ACCESS CODE

This code can be entered to access service mode without

removing the console. It only functions on washers set up for 0

vend price without any Special Pricing set-up, and the Coin/Debit

Option must be set to “J._d”. If the washer is not in failure mode,

the door must be opened to proceed. Service Access Code

contains 4 steps. Perform the following steps:

1. Press the upper left button.

2. Press the lower right button.

3. Press the upper right button.

4. Press the lower left button.

NOTE: If the Service Access Code procedure is not completed

properly, as noted above, there is a 15 second delay before it can

be attempted again.

There are 3 options to exit from the Service Mode:

1. From Set-up Code 8, press button #1 for 4 seconds.

2. Wait 2 minutes without touching any buttons (without

diagnostic modes running).

3. Power down the washer, then reapply power.

Cleaning Your Washer

Cleaning the Door Seal/Bellow

1. Open the washer door and remove any clothing or items from

the washer.

2. Inspect inner glass door. If debris is present, wipe off debris

using damp cloth.

3. Inspect the colored seal/bellow between the door opening

and the drum for stained areas. Pull back the seal/bellow

to inspect all areas under the seal/bellow and to check for

foreign objects.

A. Seal/Bellow

4. If stained areas are found, wipe down these areas of the seal/

bellow, using the procedure that follows:

a) Mix a dilute solution, using ¾ cup (177 mL) of liquid

chlorine bleach, and 1 gal. (3.8 L) of warm tap water.

b) Wipe the seal/bellow area with the dilute solution,

using a damp cloth.

c) Let stand 5 minutes.

d) Wipe down area thoroughly with a dry cloth and let

the washer interior air dry with door open.

IMPORTANT:

■ Wear rubber gloves when cleaning for prolonged periods.

■ Refer to the bleach manufacturer’s instructions for proper use.

Washer Maintenance Procedure

This washer has a special cycle that uses higher water volumes

in combination with liquid chlorine bleach to thoroughly clean the

inside of the washer.

NOTES:

■ Read these instructions completely before beginning the

cleaning process.

■ If necessary, the cleaning cycle may be interrupted by

pressing the

COLD

button twice. However, this will not

immediately stop the cycle. The washer will continue with

several rinse and drain steps to ensure that all remaining

bleach is rinsed from the washer.

Begin procedure

1. Open the washer door and remove any clothing or items from

the washer.

2. Use liquid chlorine bleach:

Open the dispenser drawer and immediately add

⁄3

cup

(160 mL) of liquid chlorine bleach to the bleach compartment.

NOTE: Do not add any detergent to this cycle. Use of more

than

⁄3

cup (160 mL) of bleach will cause product damage

over time.

3. Close the washer door and the dispenser drawer.

4. To start the Clean Washer cycle, ﬁrst enter “Start Operating

Set-up.” Then press and hold

COLD

for 1 second. With

the entire display ﬂashing, press

COLORS/DELICATES

NOTE: The drum will rotate, then the door will unlock,

lock again, and then the cycle will continue.

■ The washer will not ﬁll, but the drum will rotate while

the washer runs a short sensing cycle. This will take

approximately 3 minutes.

5. The cycle will determine whether clothing or other items are

in the washer.

a) If no items are detected in the washer, it will proceed

to Step 7.

b) If any items are detected in the washer, “rL” or “F-34”

will be displayed. Then the door will unlock.

■ Press

COLD

to cancel the failure code. Then repeat

steps 1, 3, and 4 to start the cycle again.

6. Once the cycle has begun, allow the cycle to complete.

7. After the cycle is complete, leave the door open slightly,

to allow for better ventilation and drying of washer interior.

Always do the following to maintain washer freshness:

■ Use only “HE” High Efﬁciency detergent.

■ Leave the door slightly open after each cycle to allow

for better ventilation and drying of washer interior.

■ Clean the washer monthly using the Washer Maintenance

Procedure, and

⁄3

cup (160 mL)

of liquid chlorine bleach.

■ If the procedure does not sufﬁciently improve the washer

freshness, please evaluate your installation and usage

conditions for other causes.

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to keep it looking

new. Use mild soap and water. Do not use abrasive products.

Cleaning the dispenser drawer

The dispenser drawer is removable for easy cleaning.

1. Unlock the dispenser drawer by pressing the Release Lever.

Remove the drawer.

2. Remove the inserts (the siphon from the softener and bleach

compartments).

3. Wash the parts under running water.

NOTE: Do not wash components in the dishwasher.

4. Re-install the inserts and return the dispenser to the drawer.

Water Inlet Hoses

Replace water inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace water inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your water inlet hoses, mark the date

of replacement on the label with a permanent marker.

ASSISTANCE OR SERVICE

If you need assistance:

Contact the distributor where the washer was purchased; locate

an authorized Whirlpool Commercial Laundry distributor or visit

www.whirlpoolcommerciallaundry.com.

When you call, have the washer model number and serial

number. Both numbers can be found on the serial-rating plate

located on your washer.

WASHER CARE

07/14

SÉCURITÉ DE LA LAVEUSE

EXIGENCES D’INSTALLATION

Autres pièces

Il se peut que l’installation nécessite des pièces supplémentaires.

Pour acheter l’un des articles indiqués ici, composer le numéro

sans frais indiqué à la section “Assistance ou service”.

Si vous avez Vous devrez acheter

Évier de buanderie ou

tuyau rigide de rejet à

l’égout plus haut que

96" (2,4 m)

Système de pompe de puisard

(si non déjà disponible)

Égout surélevé Évier de vidange standard de

20 gal. (76 L) de 30" (762 mm) de

hauteur ou évier utilitaire et pompe

de puisard (disponibles chez votre

fournisseur local d’articles de

plomberie)

Égout au plancher Brise-siphon, pièce n° 285834;

tuyau de vidange additionnel,

pièce n° 8318155; et ensemble

de connexion, pièce n° 285835

Tuyau de vidange trop

court

Trousse de rallonge du tuyau de

vidange de 4 pi (1,2 m), pièce n°

285863

Robinets d’eau hors

d’atteinte des tuyaux

d’admission

2 tuyaux d’admission d’eau plus

longs :

6 pi (1,8 m), pièce n° 76314

10 pi (3,0 m), pièce n° 350008

Outillage et pièces

Rassembler les outils et pièces nécessaires avant de commencer

l’installation. Les pièces fournies se trouvent dans le tambour

de la laveuse.

Outils nécessaires au raccordement des tuyaux d’arrivée

d’eau

■ Pince (ouverture jusqu’à

⁄16" [39,5 mm])

■ Lampe de poche

(facultative)

Outils nécessaires à l’installation

■ Clés plates de ½"

⁄16"

■ Tournevis de sécurité

Torx T-20

®†

■ Tourne-écrou de ¼"

■ Niveau

■ Cale en bois

■ Règle ou mètre ruban

Pièces fournies

Accessoires

Vous pouvez faciliter l’utilisation de votre laveuse avec

ces accessoires de première qualité.

Pour vous informer au sujet des autres articles de qualité

ou pour commander, composez le 1-800-901-2042

ou consultez le site www.whirlpool.com/accessories.

Au Canada, composez le 1-800-807-6777 ou consultez

le site Internet www.whirlpoolparts.ca.

Produit numéro Accessoire

8212526

Plateau d’égouttement de la laveuse,

convient à tous les modèles

31682

Produit de nettoyage polyvalent pour

appareils ménagers

1903WH

Casier de rangement de fournitures

de buanderie

A. Bride de retenue pour tuyau

de vidange (en forme de U)

B. Tuyaux d’arrivée d’eau (2)

C. Rondelles pour tuyau

d’arrivée d’eau (4)

®†TORX et T20 sont les marques déposée de Acument Intellectual Properties, LLC.

A B

D. Bouchons pour les trous

des boulons de transport (4)

E. Attache de ﬁxation amovible

Dégagements de séparation à respecter

■ L’emplacement doit être assez grand pour permettre

d’ouvrir complètement la porte de la laveuse.

■ Prévoir davantage d’espace pour faciliter l’installation

et l’entretien. La porte s’ouvre à plus de 90° et n’est pas

réversible.

■ Un espace supplémentaire peut être requis pour les

moulures de porte et de plancher et pour les plinthes.

■ Un espace supplémentaire de 1" (25 mm) de tous les côtés

de la laveuse est recommandé pour réduire le transfert

du bruit.

■ Il faut aussi prendre en compte l’espace requis entre

les appareils voisins.

Dimensions de la laveuse

Door is not reversible

/16"

(732 mm)

/8"

(1134 mm)

27"

(686 mm)

50 ½"

(1282 mm)

*Hauteur sans les pieds de nivellement installés.

Un système de vidange au plancher doit être installé sous la

cloison. Des cloisons pré-fabriquées avec prises de courant,

canalisations d’arrivée d’eau, et aménagements pour installation

de vidange ne doivent être installés que là où les codes locaux

l’autorisent.

Exigences d’emplacement

Le choix d’un emplacement approprié pour la laveuse

en améliore le rendement et réduit au minimum le bruit

et le “déplacement” possible de la laveuse.

La laveuse peut être installé sous un comptoir personnalisé,

dans un sous-sol, une salle de buanderie ou un encastrement.

Voir “Système de vidange”.

Il faut aussi prendre en compte les exigences d’emplacement des

appareils voisins. C’est à l’utilisateur qu’incombe la responsabilité

de réaliser une installation correcte.

Il vous faudra

■ Un chauffe-eau conﬁguré pour fournir de l’eau à 120°F

(49°C) à la laveuse.

■ Une prise électrique reliée à la terre située à moins de

6 pi (1,8 m) du cordon d’alimentation électrique ﬁxé à l’arrière

à la laveuse. Voir “Spéciﬁcations électriques”.

■ Des robinets d’eau chaude et d’eau froide situés à moins

de 4 pi (1,2 m) des robinets d’admission d’eau chaude

et d’eau froide et une pression d’eau de 20–100 lb/po²

(137,9–689,6 kPa).

■ Un plancher de niveau ayant une pente maximale de

1" (25 mm) sous l’ensemble de la laveuse. L’installation

de la laveuse sur des surfaces de sol molles, telles que

tapis ou surfaces avec sous-couche en mousse n’est pas

recommandée.

■ Un plancher robuste et solide capable de soutenir le poids

total de la laveuse (eau et charge) de 400 lbs (180 kg).

Ne pas faire fonctionner la laveuse à des températures inférieures

à 32ºF (0ºC). Une quantité d’eau peut demeurer dans la laveuse

et causer des dommages à des températures basses.

Options

Piédestal

Vous avez la possibilité d’acheter des piédestaux séparément

pour cette laveuse. Le piédestal augmentera la hauteur totale

de la laveuse.

Piédestal facultatif

Hauteur du

piédestal

Hauteur

approximative

avec laveuse

Couleur

Numéro

de modèle

⁄8" (73 mm) *47,5" (1207 mm) Blanc WHP0400VW

*Ajouter 5⁄8" (16 mm) minimum pour les pieds de nivellement.

Système de vidange

La laveuse peut être installé en utilisant le système de rejet

à l’égout (au plancher ou mural), le système de vidange de

l’évier de buanderie, ou le système de vidange au plancher.

Sélectionner la méthode d’installation du tuyau de vidange

selon les besoins. Voir “Outillage et pièces”.

Système de vidange avec tuyau de rejet à l’égout – mural

ou au plancher (vues A et B)

Le système de rejet à l’égout nécessite un tuyau rigide d’un

diamètre minimum de 2" (50 mm). La capacité minimale

d’acheminement ne doit pas être inférieure à 12 gal. (45,5 L)

par minute et par laveuse.

Le sommet du tuyau rigide de rejet à l’égout doit être au moins

à 30" (762 mm) de hauteur et au maximum à 96" (2,4 m) de la

base de la laveuse.

Système de vidange avec évier de buanderie

L’évier de buanderie doit avoir une capacité minimale de

20 gal. (76 L). La partie supérieure de l’évier de buanderie

doit être à au moins 30" (762 mm) au-dessus du plancher.

Spécifications électriques

■ Une alimentation de 120 volts, 60 Hz, CA seulement,

de 15 ou 20 ampères, protégée par un fusible est requise.

On recommande d'utiliser un fusible ou un disjoncteur

temporisé. Il est recommandé de raccorder la laveuse

sur un circuit distinct exclusif à cette laveuse.

■ Cette laveuse comporte un cordon d’alimentation électrique

à trois broches pour liaison à la terre.

■ Pour minimiser les risques de choc électrique, on doit

brancher le cordon sur une prise de courant de conﬁguration

correspondante, à 3 alvéoles, reliée à la terre et installée

conformément aux codes et règlements locaux. Si une

prise de courant de conﬁguration correspondante n’est pas

disponible, le client a la responsabilité et l’obligation de

faire installer par un électricien qualiﬁé une prise de courant

correctement reliée à la terre.

■ Si les codes le permettent et si on utilise un conducteur

distinct de liaison à la terre, il est recommandé qu’un

électricien qualiﬁé vériﬁe la qualité de la liaison à la terre.

■ Ne pas utiliser une tuyauterie de gaz pour le raccordement

à la terre.

■ En cas de doute quant à la qualité de la liaison à la terre

de la laveuse, consulter un électricien qualiﬁé.

■ Ne pas installer un fusible dans le conducteur neutre

ou le conducteur de liaison à la terre.

Vue arrière

Système de vidange au plancher

Le système de vidange au plancher nécessite un brise-siphon

qui peut être acheté séparément. Voir “Outillage et pièces”.

Le brise-siphon doit être au moins à 28" (710 mm) de la base

de la laveuse. Des tuyaux supplémentaires peuvent être requis.

30" min.

(762 mm)

28" min.

(710 mm)

30" min.

(762 mm)

Shipping bolt

2. Au moyen d’une clé de ½", desserrer chacun des boulons.

3. Une fois le boulon desserré, le déplacer au centre du

trou et retirer complètement le boulon, y compris la cale

d’espacement en plastique couvrant le boulon.

4. Une fois que les 4 boulons ont été retirés, jeter les boulons

et les cales d’espacement. Puis pousser la ﬁche du cordon

d’alimentation électrique à travers l’ouverture sur le côté droit

du panneau arrière, tirer le cordon d’alimentation électrique

à travers l’ouverture sur le côté gauche du panneau arrière

et obturer les trous avec le bouchon fourni. Ne pas tirer

l’extrémité du cordon d’alimentation à travers le trou de droit.

5. Obturer les trous des boulons avec les 4 bouchons

d’obturation des boulons de transport.

REMARQUE : Si la laveuse doit être transporté à une date

ultérieure, appeler le distributeur ou l’installateur du produit. Pour

éviter des dommages concernant la suspension et la structure,

votre laveuse doit être correctement monté pour réinstallation

ultérieure par un technicien certiﬁé.

Boulon

d’expédition

INSTRUCTIONS

D’INSTALLATION

Dépose du système de transport

IMPORTANT : Positionner la laveuse de sorte que l’arrière de la

laveuse soit à environ 3 pi (900 mm) de son emplacement ﬁnal.

On trouve sur le panneau arrière de la laveuse 4 boulons

d’expédition qui soutiennent le système de suspension durant le

transport. Ces boulons retiennent aussi le cordon d’alimentation

électrique à l’intérieur de la laveuse jusqu’à ce que les boulons

soient retirés.

Boulon d’expédition avec cale d’espacement en plastique

1. Laisser la laveuse en position verticale pendant que l’on ôte

les boulons d’expédition.

Raccordement des tuyaux d’alimentation

Insérer les rondelles plates neuves (fournies) dans chaque

extrémité des tuyaux d’arrivée d’eau. Insérer fermement

les rondelles dans les raccords.

A B

A. Raccord

B. Rondelle

Connecter les tuyaux d’arrivée d’eau aux robinets d’eau

S’assurer que le tambour de la laveuse est vide.

1. Fixer un tuyau au robinet d’eau chaude. Visser complètement

le raccord à la main pour qu’il comprime le joint.

2. Fixer un tuyau au robinet d’eau froide. Visser complètement

le raccord à la main pour qu’il comprime le joint.

3. À l’aide d’une pince, serrer les raccords en effectuant deux

tiers de tour supplémentaires.

REMARQUE : Ne pas serrer excessivement ou utiliser du ruban

adhésif ou un calfeutrant sur la valve. Les valves risquent d’être

endommagées.

Purger les canalisations d’eau

■ Laisser s’écouler l’eau des deux robinets et des tuyaux

d’alimentation dans un évier de buanderie, un tuyau rigide

de rejet à l’égout ou un seau, pour éliminer les particules se

trouvant dans les canalisations d’eau qui pourraient obstruer

les tamis de la valve d’arrivée d’eau.

■ Vériﬁer la température de l’eau pour s’assurer que le tuyau

d’eau chaude est connecté au robinet d’eau chaude et que

le tuyau d’eau froide est connecté au robinet d’eau froide.

Connecter les tuyaux d’arrivée d’eau à la laveuse

C. Tuyau d’arrivée d’eau froide

H. Tuyau d’arrivée d’eau chaude

1. Fixer le tuyau d’eau chaude à la valve du tuyau d’arrivée

d’eau chaude (H) de la laveuse. Visser complètement

le raccord à la main pour qu’il comprime le joint.

2. Fixer le tuyau d’eau froide au robinet d’eau froide (C)

de la laveuse. Visser complètement le raccord à la main

pour qu’il comprime le joint.

3. À l’aide d’une pince, serrer les raccords en effectuant deux

tiers de tour supplémentaires.

REMARQUE : Ne pas serrer excessivement. Le raccord

risque d’être endommagé.

4. Ouvrir les robinets d’eau complètement et vériﬁer s’il y

a des fuites.

REMARQUE : Remplacer les tuyaux d’arrivée d’eau après

5 ans d’utilisation pour réduire le risque de défaillance. Prendre

note de la date d’installation ou de remplacement des tuyaux,

pour référence ultérieure.

Inspecter périodiquement les tuyaux; les remplacer en cas de

renﬂement, de déformation, de coupure, d’usure ou si une fuite

se manifeste.

La page charge ...

Samsung CHW9060AW Le manuel du propriétaire

Marque: Samsung

Modèle: CHW9060AW

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

CHW9150GW

Télécharger le PDF

rapport

dans d''autres langues

English: Samsung CHW9060AW Owner's manual

Samsung CHW9060AW Le manuel du propriétaire

Ce manuel convient également à

Samsung CHW9060AW Le manuel du propriétaire

dans d''autres langues

Autres documents