VTech VM511 Manuel utilisateur

Marque: VTech

Modèle: VM511

Catégorie: Babyphones

Taper: Manuel utilisateur

Plug the battery connector securely into

the socket.

NOTES

Make sure the supplied rechargeable battery with

the label THIS SIDE UP facing up.

Arrange the battery wire to avoid it obstructing the

battery cover when closing.

3 Align the battery compartment cover flat

against the battery compartment, then

place down and slide it towards the center

of the parent unit until it clicks into place.

•

User’s manual

VM511/VM511-2

Safe & SoundTM

Full Color Video and Audio

Monitor

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechphones.com.

3-month warranty!

Visit www.vtechphones.com.

Registration

enhanced warranty support.

Product news

Learn about the latest VTech

products.

You can power up the parent unit by connecting

it to AC power or to the rechargeable battery

provided. Even if the parent unit is connected

to AC power, we recommend you also

install the battery. This guarantees continual

operation in case of a power outage.

Install the battery as shown below.

Slide and lift to open the battery compartment

cover.

Install the battery

Replace the battery

To replace the battery, pull the battery out of

the battery compartment and unplug the battery

connector from the socket, then follow the steps

above to install the battery.

NOTES

The operating time for using the rechargeable

battery is short. If you want to monitor your baby

for a long time, we recommend you connect the

parent unit to AC power.

If the parent unit will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

•

Connect the baby monitor

Charge the parent unit battery

Once you have connected the parent unit and

installed its battery, press to turn it on. The

battery icon indicates the battery status (see

the following table).

NOTES

The parent unit battery is fully charged after

12 hours of continuous charging.

It takes longer to charge the battery when the

parent unit is turned on. To shorten the charging

time, turn the parent unit off while charging.

The standby time varies depending on the

sensitivity level you set, your actual use, and the

age of the battery.

Battery

indicators

Battery

status

Action

The battery

icon is off and

displays.

No battery

is installed

but operates

using AC

power, or the

battery has

been installed

incorrectly.

Install the

parent unit

battery.

Charge

without

interruption

(at least 30

minutes).

The screen

displays .

The light

flashes.

The battery

has very little

charge and

may be used

for only a

short time.

Charge

without

interruption

(about 30

minutes).

The battery

icon becomes

solid .

The battery is

fully charged.

To keep

the battery

charged,

connect it to

AC power

when not in

use.

•

You may test the baby monitor before initial

use, and at regular times thereafter.

To test your video and audio monitor:

Place the parent unit and the baby units in

the same room to test the product. Make

sure the baby units are at least 3 feet away

from the parent unit.

Press to turn on the baby unit. The

POWER light turns on.

3. Press to turn on the parent unit. The

screen turns on.

NOTE

If both units are not connected, the parent unit

displays while searching for a baby unit. If no baby

unit is found after a while, it displays .

Before use

Baby unit overview

1Camera

2Infrared LEDs

Backup light for night vision.

3POWER on/off indicator

On when the baby unit is powered on

and currently linked to parent unit.

Flashes when the baby unit is not

linked to a parent unit; or

the pairing process is in progress; or

the parent unit is not viewing this baby

unit.

•

4Power jack

5Control key panel

/VOL+

Press to increase the listening volume.

/VOL

Press to decrease the listening volume.

PAIR

Press and hold to pair to the parent unit.

(On/Off)

Press and hold to turn on or off.

6Microphone

7Stand

Tilt to adjust the camera angle.

8Rim

9Base

Parent unit overview

1Visual sound indicator

The visual sound indicator has two

functions. One is to show the sound level

detected by the baby unit. The other

one is to show the volume level during

speaker volume setting.

Sound level detected by the baby unit

One to three green

lights indicate a moderate sound level

detected by the baby unit.

Additional red

lights indicate a higher sound level

detected by the baby unit (e.g. baby

crying loudly).

Speaker volume level

One to three green

lights indicate Level 1 to Level 3 of

the speaker volume setting.

Additional red

lights indicate Level 4 to Level 5 of

the speaker volume setting.

•

2 Battery level indicator

Light On when the parent unit battery

is being charged.

Light Flashes when the parent unit

battery is low and needs charging.

Light Off when the parent unit battery

is fully charged, or when no battery is

installed.

•

3POWER on/off indicator

On when the parent unit is turned on.

Flashes when in pairing process, or

when connecting to baby unit while

the baby unit is not available.

•

4Power jack

Overview

5Control key panel

/VOL+

Press to increase the speaker volume.

While in the menu, press to scroll up.

While viewing a zoomed image,

press and hold to move the image

upward.

MENU/SELECT

Press to enter the menu.

While in a menu, press to choose an

item, or save a setting.

/VOL

Press to decrease the speaker volume.

While in the menu, press to scroll

down.

While viewing a zoomed image,

press and hold to move the image

downward.

While in a menu, press to choose the

option on the left side.

While viewing a zoomed image, press

to zoom out; or

press and hold to move the image

leftward.

While in a menu, press to choose the

option on the right side.

While viewing image, press to zoom in.

While viewing a zoomed image,

press and hold to move the image

rightward.

TALK

While viewing image, press and hold to

talk to the selected baby unit.

(On/off)

Press and hold to turn on or off.

Press to turn on or off the screen.

•

6Slot for portable use

7Stand

8Battery compartment cover

What’s in the box

1 set for VM511;

2 sets for VM511-2

Power on or off the baby unit

Press to turn on the baby unit. The

POWER light turns on.

Press and hold again to turn off the baby

unit. The POWER light turns off.

Power on or off the parent unit

Press to turn on the parent unit. The

screen turns on.

Press and hold again to turn off the

parent unit. The screen turns off.

Turn on or off the parent unit screen

If you want to hear sound from baby unit without

watching the screen, you can choose to turn off

the screen to save power. You can turn it back on

later when necessary.

Press on the parent unit at any time.

Adjust the speaker volume for

baby unit

You can adjust the speaker volume.

Press /VOL+ or /VOL

on the baby unit

at any time.

Adjust the speaker volume for

parent unit

You can adjust the speaker volume from

to , or turn it off. The preset speaker

volume is ..

Press /VOL+ or /VOL

on the parent

unit when it is not in use.

When the speaker volume is set to off, the

screen displays .

Adjust the LCD brightness of the

parent unit

You can adjust the brightness of the parent

unit screen from to . The LCD

brightness is preset to ..

Press MENU/SELECT when the parent unit

is not in use.

Press or to scroll to .

Press or to adjust the brightness.

Press MENU/SELECT to confirm your

selection.

•

Parent unit display icons

Connection status

- displays when strong signal

strength is detected between the

baby unit and the parent unit.

- , or displays when moderate

signal strength is detected between

the baby unit and the parent unit.

- displays when the link between the

baby unit and the parent unit is lost.

- displays when the parent unit is

searching for a baby unit.

(x:1-4)

Current view status

- Display the number of the baby unit

that is being viewed.

Zoom

- Display when the camera at the

baby unit has zoomed in.

Volume off

- Display when the volume is turned off.

Sound activation

- Display when the sound activation

is on.

Battery status

- animates

when the battery is charging.

- displays solid when the battery is

fully charged.

- displays when the battery is low

and needs charging.

- displays when no battery is installed

but operates using AC power, or the

battery has been installed incorrectly.

Using the baby monitor

Parent unit main menu icons

Camera selection

You can select the screen to view

images from a particular baby unit,

or view all baby units in Patrol Mode.

•

Brightness

You can adjust the brightness of

the screen. The LCD brightness isThe LCD brightness is

preset to .

- brightest screen display.

- brighter screen display.

- average screen brightness.

- darker screen display.

- darkest screen display.

•

Sensitivity

With this feature, you can choose

to hear sounds from the baby unit

all the time, or to hear sounds that

exceed a certain level. You can

use the parent unit to adjust the

microphone sensitivity of your baby

unit. The higher the sensitivity level,

the more sensitive the baby unit is

in detecting sounds for transmitting

to the parent unit. The sound

sensitivity is preset to ..

- high sensitivity level.

- medium high sensitivity

level.

- medium sensitivity level.

- medium low sensitivity level.

- low sensitivity level.

•

Sound activation

Automatically turns on the parent

unit screen when a sound is

detected in your baby’s room. When

no sound is detected, the screen is

off to save power.

- turn on sound activation.

- turn off sound activation.

•

Pairing

The baby units and parent unit

provided are already paired. You can

add or replace baby units (VM501

purchased separately) to your baby

monitor system.

•

Night vision

The baby unit has infrared LEDs that allow you

to see your baby clearly at night or in a dark room.

When the baby unit detects low light levels, the

infrared LEDs are switched on automatically.

NOTE

When the infrared LEDs are on, the image is in black

and white. This is normal due to external light sources.

TIP

Depending on the surroundings and other interfering

factors, like lightings, objects, colors and

backgrounds, the display resolution may vary. Adjust

the baby unit’s angle or place the baby unit at a higher

level to prevent glare and blurry display.

Add new baby unit (VM501)

The baby units and parent unit provided are

already paired. You can add or replace any baby

units (VM501 purchased separately) to your

video and audio monitor system. You can pair a

maximum of four baby units to your parent unit.

For more details, refer to the user’s manual that

comes with your VM501 new baby unit.

Adjust the sound sensitivity of

the baby unit

You can choose to hear sounds from the baby

unit all the time, or to hear sounds that exceed

a certain level. You can use the parent unit to

adjust the microphone sensitivity of your baby

unit. The higher the sensitivity level, the more

sensitive the baby unit is in detecting sounds

for transmitting to the parent unit. The sound

sensitivity is preset to .

Sound sensitivity table for reference

Icon display Sensitivity Description

High sensitivity level

The parent unit speaker is

constantly on, and you will

hear all sounds (including

background noises) from

your baby’s room.

Medium high sensitivity

level

The parent unit speaker

turns on for soft babbling

and louder sounds from

your baby. It remains

quiet when your baby

sleeps soundly.

Medium sensitivity level

The parent unit speaker

turns on for loud babbling

and louder sounds from

your baby. It remains quiet

when your baby makes

soft sounds.

Medium low sensitivity

level

The parent unit speaker

turns on for crying and

louder sounds from your

baby. It remains quiet

when your baby makes

soft sounds.

Low sensitivity level

The parent unit speaker

turns on for loud crying

or screeching sounds

from your baby. It remains

quiet when your baby

makes soft sounds.

Press MENU/SELECT when the parent unit is

not in use.

Press or to scroll to .

Press or to adjust the sensitivity level.

Press MENU/SELECT to confirm your selection.

TIP

You can adjust the baby unit placement to improve

the sound detection.

Turn on or off the sound activation

The parent unit continuously monitors the sound

level in your baby’s room. When the sound

activation mode is on, the parent unit screen

turns on when the baby unit detects a sound.

As long as no sound is detected within 50 seconds,

the parent unit screen is off to save power. When

your baby starts to cry, the sound activation triggers

the parent unit screen automatically turns on.

Press MENU/SELECT when the parent unit

is not in use.

Press or to scroll to .

Press or to select to turn on, or

to turn off sound activation.

Press MENU/SELECT to confirm your selection.

NOTES

If you mute the speaker while sound activation

is on, then you hear a beep sound whenever the

screen turns on.

If you want to turn on the parent unit screen

continuously while the sound activation is on,

then set the sound sensitivity to .

Select the camera

You can select the screen to view images from

a particular baby unit, or view all baby units in

Patrol Mode. If you select Patrol Mode to view

the images, the screen switches to view another

baby unit automatically after some time. The

switching is in chronological order: to .

Press MENU/SELECT when the parent unit is

not in use.

Press or to scroll to .

Press or to select the desired baby unit

(1, 2, 3 or 4) or Patrol Mode ( ).

Press MENU/SELECT to confirm your selection.

Zoom

You can zoom in or out while viewing image

from baby unit.

Press to zoom in.

Press and hold , , or to move the

zoomed image upward, downward, leftward

or rightward correspondingly.

Press to zoom out.

Talk function

You can use the TALK function of the parent

unit to talk and comfort your baby.

Press and hold TALK when the parent

unit is viewing particular baby unit. Speak

towards the microphone on the parent unit.

Your voice is broadcast to the baby unit.

•

High

sensitivity

Low

sensitivity

Positioning the baby monitor

NOTE

This baby monitor is intended as an aid. It is not a

substitute for proper adult supervision, and should not

be used as such.

CAUTION

Keep the baby unit out of the reach of the baby. Never

place or mount the baby unit inside the baby’s crib or

playpen.

Place the baby unit at least 1 meter / 3 feet

away from your baby.

NOTE

If you experience audio feedback on either the parent

unit or baby unit, move the parent unit further away

until there is no more audio feedback; or press

/VOL

on the parent unit to lower the audio

feedback sound.

2. Place the parent unit at least 1 meter / 3

feet away from the baby unit.

TIP

You can increase the speaker volume of the parent

unit if you cannot hear the sounds transmitted from

the baby unit.

Operating range

The operating range of the baby monitor is

up to 300 meters (1,000 feet) outdoors or

50 meters (160 feet) indoors. The actual

operating range may vary depending on

the environmental conditions, and other

interferences such as walls, doors, and other

obstructions.

NOTES

Use only the battery supplied with this product.

Use only the parent unit power adapter or the baby

unit power adapter supplied with this product.

The parent unit power adapter and baby unit

power adapter are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.

Make sure the parent unit, the baby unit and the

power adapter cord are out of reach of children.

•

Connect and charge the

battery

NOTE

Sling is not included. You may need to buy a sling for

portable usage.

Make sure battery is installed and charged.

Unplug the power adaptor.

Pinch the end of the sling and insert it into

the slot on the top of the parent unit.

Insert the one end of the sling into the other

end of the sling, and fasten it.

Portable use of parent unit

(optional)

At least 1 meter (3 feet)

At least 1 meter

(3 feet)

At least 1 meter (3 feet)

THIS SIDE UP

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during

the limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair or

replace at VTech’s option, without charge, a

Materially Defective Product. If we repair the Product,

we may use new or refurbished replacement

parts. If we choose to replace the Product, we

may replace it with a new or refurbished Product

of the same or similar design. We will retain

defective parts, modules, or equipment. Repair or

replacement of the Product, at VTech’s option, is

your exclusive remedy. VTech will return the repaired

or replacement Products to you in working condition.

You should expect the repair or replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If VTech

repairs or replaces a Materially Defective Product

under the terms of this limited warranty, this limited

warranty also applies to the repaired or replacement

Product for a period of either (a) 90 days from the date

the repaired or replacement Product is shipped to

you or (b) the time remaining on the original one-year

warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, fire, water or other

liquid intrusion; or

Product that has been damaged due to repair,

alteration or modification by anyone other than an

authorized service representative of VTech; or

Product to the extent that the problem

experienced is caused by signal conditions,

network reliability, or cable or antenna systems; or

Product to the extent that the problem is caused

by use with non-VTech accessories; or

Below are the questions most frequently asked about

the baby monitor. If you cannot find the answer to

your question, contact customer service by visiting our

website at www.vtechphones.com or calling

1 (800) 595-9511.

FCC Part 15

This equipment has been tested and found to comply

with the requirements for a Class B digital device

under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment

and receiver.

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV

technician for help.

Changes or modifications to this equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

•

The RBRC® seal on the nickel-metal battery indicates

that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and

recycle these batteries at the end of their useful lives,

when taken out of service within the United States

and Canada.

The RBRC® program provides a convenient

alternative to placing used nickel-metal batteries into

the trash or municipal waste, which may be illegal in

your area.

VTech’s participation in RBRC® makes it easy for

you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized

VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH

battery recycling and disposal bans/restrictions in

your area. VTech’s involvement in this program is

part of its commitment to protecting our environment

and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered

trademarks of Rechargeable Battery Recycling

Corporation.

Frequently asked

questions

When you are not going to use the baby monitor for

some time, remove the rechargeable battery from the

parent unit. Store the parent unit, the baby unit and the

adapters in a cool and dry place.

Storage

Why does the

baby monitor

not respond

normally?

Try the following (in the order

listed) for common cure:

1. Disconnect the power to the

baby units and the parent unit.

2. Remove the batteries in the

parent unit. Then install the

batteries again.

3. Wait a few minutes before

connecting power back to the

baby units and the parent unit.

4. Turn on the baby units and the

parent unit.

5. Wait for the parent unit to

synchronize with the baby units.

Allow up to one minute for this to

take place.

Why don’t

the power-on

light of the

baby unit and

parent unit

go on when I

switch on the

units?

Perhaps the rechargeable battery

of the parent unit is empty and

the parent unit is not connected

to the mains. Insert the appliance

plug into the parent unit and put

the adapter in a wall socket. Then

press to switch on the parent

unit and to establish connection

with the baby unit.

Perhaps the baby unit is not

connected to the mains. Connect

the baby unit to the mains. Then

set ON/OFF switch to ON to switch

on the baby unit and to establish

connection with the parent unit.

Why is my

screen in

black and

white?

The screen is in black and white

during nighttime or in a dark room.

This is normal due to external light

sources.

Why do I get

glare or blurry

display on my

screen when

viewing my

baby at night?

During nighttime or in a dark

room, the surroundings and other

interfering factors, like lightings,

objects, colors and backgrounds

may affect the image quality on

your parent unit screen. Adjust

the baby unit’s angle or place

the baby unit at a higher level to

prevent glare and blurry display.

Why does the

baby monitor

produce a

high-pitched

noise?

The units may be too close to

each other. Make sure the parent

unit and the baby unit at least

1 metre/3 feet away from each

other.

The RBRC® seal

FCC and IC regulations

Limited warranty Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered illegible; or

Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products

used for rental purposes); or

Product returned without a valid proof of purchase

(see item 2 on the next page); or

Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls and

features may save you a service call.

Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery or

handling charges incurred in the transport of the

Product(s) to the service location. VTech will return

repaired or replaced Product under this limited

warranty. Transportation, delivery or handling

charges are prepaid. VTech assumes no risk for

damage or loss of the Product in transit. If the

Product failure is not covered by this limited warranty,

or proof of purchase does not meet the terms of

this limited warranty, VTech will notify you and will

request that you authorize the cost of repair prior

to any further repair activity. You must pay for the

cost of repair and return shipping costs for the repair

of Products that are not covered by this limited

warranty.

What must you return with the Product to get

warranty service?

Return the entire original package and

contents including the Product to the VTech

service location along with a description of the

malfunction or difficulty; and

Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product

model) and the date of purchase or receipt; and

Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to

this Product. VTech provides no other warranties for

this Product. The warranty exclusively describes all

of VTech’s responsibilities regarding the Product.

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

Baby unit: 2407.5 - 2475 MHz

Parent unit: 2407.5 - 2475 MHz

Channels 21

LCD 2” Color LCD

(QVGA 320x240 pixel)

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirement

Parent unit: 3.6 V Ni-MH battery

Baby unit power adapter:

Input: 100-240V AC 150mA 50/60Hz

Output: 6V DC 600mA

Parent unit power adapter:

Input: 100-240V AC 150mA 50/60Hz

Output: 6V DC 600mA

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately

8 in (20 cm) or more. The transmitter and antenna

shall be held at least 1 in (2.5 cm) from your face.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device complies with Industry Canada licence-

exempt RSS standard(s).

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

Privacy of communications may not be ensured when

using this product.

The term ‘’IC:‘’ before the certification/registration

number only signifies that the Industry Canada

technical specifications were met.

This product meets the applicable Industry Canada

technical specifications.

RF radiation exposure statement

The baby unit complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The baby unit should be installed and

operated with a minimum distance of 8 in (20 cm)

between the baby unit and all persons’ body. Use of

other accessories may not ensure compliance with

FCC RF exposure guidelines. This transmitter must

not be co-located or operating in conjunction with

any other antenna or transmitter. This equipment

complies also with Industry Canada RSS-102 with

respect to Canada’s Health Code 6 for Exposure of

Humans to RF Fields.

There are no other express warranties. No one

is authorized to make modifications to this limited

warranty and you should not rely on any such

modification.

State/Provincial Law Rights: This warranty gives you

specific legal rights, and you may also have other rights,

which vary from state to state or province to province.

Limitations: Implied warranties, including those of

fitness for a particular purpose and merchantability

(an unwritten warranty that the Product is fit for

ordinary use) are limited to one year from the date

of purchase. Some states/provinces do not allow

limitations on how long an implied warranty lasts,

so the above limitation may not apply to you. In no

event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages

(including, but not limited to lost profits or revenue,

inability to use the Product or other associated

equipment, the cost of substitute equipment, and

claims by third parties) resulting from the use of this

Product. Some states/provinces do not allow the

exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may

not apply to you.

Please retain your original sales receipt as proof

of purchase.

Technical specications

Specifications are subject to change without notice.

Document order number: 91-008409-010-100

This baby monitor meets the California Energy

Commission (CEC) regulations for energy consumption.

Your baby monitor is set up to comply with the

energy-conserving standards right out of the box.

Follow the instructions to install and charge the battery.

The CEC battery charging testing mode is activated

while charging.

Even if the parent unit is paired to baby units, the CEC

battery charging testing mode is activated while it is

powered off and charging.

California Energy Commission

battery charging testing mode

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez

toujours suivre certaines mesures de précaution

de base afin de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont ceux

qui suivent :

Observez toutes les instructions et mises en garde

inscrites sur l’appareil.

L’installation par un adulte est requise.

Ce produit a été conçu pour être un dispositif

d’appoint seulement. Il n’est pas le remplacement

d’une supervision responsable et adéquate par un

adulte et ne devrait pas être utilisé comme telle.

Ce produit n’est pas conçu pour être utilisé en tant

que moniteur médical.

N’utilisez pas cet appareil près de l’eau ni de toute

autre source d’humidité, par exemple, près d’une

baignoire, cuve à lessive, évier de cuisine, dans

un sous-sol humide ni près d’une piscine, dans un

soussol humide ou une douche.

MISE EN GARDE: Il peut y avoir un risque

d’explosion si vous utilisez le mauvais type de piles

pour l’unité du parent. N’utilisez que le bloc-piles

rechargeable inclus ou le bloc-piles de rechange

(BT185645/BT285645). N’incinérez pas les piles.

Celles-ci risqueraient d’exploser. Jetez les piles

usées selon les renseignements suivant le sceau

du RBRC®.

N’utilisez que les adaptateurs inclus avec ce produit.

L’utilisation d’un adaptateur dont la polarité ou la

tension serait inadéquate risque d’endommager

sérieusement le produit et mettre votre sécurité en

péril.

Adaptateur de l’unité du bébé :

Entrée 100-240V CA 150mA 50/60 Hz;

Sortie : 6 V CC 600 mA

Adaptateur de l’unité du parent :

Entrée 100-240V CA 150mA 50/60 Hz;

Sortie : 6 V CC 600 mA

Lorsqu’ils sont branchés dans une prise de

courant, les adaptateurs secteur ont été conçus

pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas

été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici

est branché dans une prise au plafond, sous une

table ou dans un meuble.

Débranchez ce produit de la prise de courant

avant de procéder au nettoyage. N’utilisez pas de

nettoyants en aérosols. Utilisez un chiffon humide

pour le nettoyer.

Débranchez les cordons d’alimentation avant de

remplacer le bloc-piles.

Ne coupez pas les cordons d’alimentation pour

remplacer les fiches, car ceci peut présenter un

danger potentiel.

Ne laissez aucun objet reposer ni appuyer sur

le cordon d’alimentation. N’installez pas cet

appareil dans un endroit où l’on risque d’écraser

le cordon d’alimentation ou de le piétiner.

Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur l’étiquette. Si

vous ne connaissez pas le type d’alimentation

que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale

d’électricité.

Ne surchargez pas les prises de courant murales

ni les rallonges électriques.

Ne placez pas cet appareil sur un chariot,

meuble, trépied, support de montage ni table

chancelants.

Les trous et ouvertures du boîtier, situés à

l’arrière de l’appareil ou sous celui-ci, servent à

aérer l’appareil. Pour l’empêcher de surchauffer,

ne bloquez sous aucun prétexte ces ouvertures

et n’empêchez pas l’aération adéquate de

l’appareil en le plaçant sur un lit, divan, tapis ou

toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une

source de chaleur ou d’un calorifère. De plus,

ne placez pas l’appareil dans un endroit avant

de vous assurer qu’il y ait une bonne circulation

d’air.

N’enfoncez jamais d’objets à travers les

ouvertures de cet appareil, car ils pourraient

entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui

peuvent dégénérer en incendies ou en risques

d’électrocution. Ne renversez jamais de liquide

dans ce produit.

Afin de réduire les risques d’électrocution, ne

démontez pas cet appareil, mais apportez-le

dans un centre de service autorisé. L’ouverture

du boîtier ou le retrait de toutes pièces que

contient cet appareil, à l’exception de l’accès

autorisé à certaines portes ou ouvertures,

risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage

incorrect peut par la suite présenter des risques

d’électrocution.

Vous devriez tester la réception chaque fois que

vous mettez l’appareil en fonction.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

Examinez les composantes afin de vérifier si

celles-ci ne sont pas endommagées.

Soyez avisé de la perte de la confidentialité

lorsque vous utilisez les ondes publiques. Les

conversations peuvent être entendues par

d’autres moniteurs de bébé, des téléphones

sans fil, des scanneurs, etc.

Les enfants devraient être supervisés afin de

vous assurer qu’ils ne jouent pas avec l’appareil.

Le produit n’est pas conçu pour être utilisé

par des personnes (incluant des enfants) aux

capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné

suffisamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une

personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

Utilisez et entreposez le produit à une

température entre 0˚ C (32˚F) et 40˚C (104˚ F).

N’exposez pas cet appareil à des froids ou des

chaleurs extrêmes, ainsi qu’à la lumière directe

du soleil. Ne l’installez pas près d’une source de

chauffage.

Le bloc-piles ne doit pas être exposé à la chaleur

excessive telle que la lumière du soleil ou au feu.

Assurez-vous que le moniteur et le cordon

de l’adaptateur sont toujours hors de portée

des enfants, à au moins 1 mètre (3 pieds) de

l’enfant ou du berceau, pour éviter tout risque de

strangulation.

Ne jamais placer le moniteur à l’intérieur du

berceau ou du parc de bébé. Ne jamais couvrir

le moniteur ou l’unité (s) portative avec un article

tel une serviette ou une couverture.

D’autres équipements électroniques peuvent

produire des interférences sur votre moniteur

vidéo et audio. Tentez d’installer votre

moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans fil,

radios, téléphones cellulaires, interphones,

moniteurs, téléphones, ordinateurs personnels,

électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux

dispositifs numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une firme de recherche indépendante,

a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs

et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des

aliments et drogues (FDA) des États-Unis, la firme

WTR recommande aux médecins:

20.

21.

22.

23.

For cETL compliance only

When using your equipment, basic safety

precautions should always be followed to

reduce the risk of fire, electric shock and injury,

including the following:

Follow all warnings and instructions marked

on the product.

Adult setup is required.

This product is intended as an aid. It is not

a substitute for responsible and proper adult

supervision and should not be used as such.

This product is not intended for use as a

medical monitor.

Do not use this product near water. For

example, do not use it next to a bath tub, wash

bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion

if a wrong type of battery is used for the parent

unit. Use only the supplied rechargeable

battery or replacement battery pack

(BT185645/BT285645) for the parent unit. Do

not dispose of batteries in a fire. They may

explode. Dispose of used battery according to

the information in The RBRC® seal.

Use only the adapters included with this

product. Incorrect adapter polarity or voltage

can seriously damage the product.

Baby unit power adapter: Input 100-240V

AC 150mA 50/60Hz; Output: 6V DC 600mA

Parent unit power adapter: Input 100-240V

AC 150mA 50/60Hz; Output: 6V DC 600mA.

The power adapters are intended to be

correctly oriented in a vertical or floor mount

position. The prongs are not designed to

hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

Unplug this product from the wall outlet

before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

Unplug the power cords before replacing

batteries.

Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.

Do not allow anything to rest on the power

cords. Do not install this product where the

cords may be walked on or crimped.

This product should be operated only from

the type of power source indicated on the

marking label. If you are not sure of the type

of power supply in your home, consult your

dealer or local power company.

10.

11.

12.

13.

Do not overload wall outlets or use an

extension cord.

Do not place this product on an unstable

table, shelf, stand or other unstable surfaces.

This product should not be placed in

any area where proper ventilation is not

provided. Slots and openings in the back

or bottom of this product are provided

for ventilation. To protect them from

overheating, these openings must not be

blocked by placing the product on a soft

surface such as a bed, sofa or rug. This

product should never be placed near or over

a radiator or heat register.

Never push objects of any kind into this

product through the slots because they may

touch dangerous voltage points or create a

short circuit. Never spill liquid of any kind on

the product.

To reduce the risk of electric shock, do

not disassemble this product, but take it to

an authorized service facility. Opening or

removing parts of the product other than

specified access doors may expose you to

dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when

the product is subsequently used.

You should test the sound reception every

time you turn on the units or move one of

the components.

Periodically examine all components for

damage.

Be aware of possible loss of privacy while

using public airwaves. Conversations may

be picked up by other nursery monitors,

cordless phones, scanners, etc.

Children should be supervised to ensure

that they do not play with the product.

The product is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

Important safety

instructions

Cautions

Use and store the product at a temperature

between 32oF and 104oF.

Do not expose the product to extreme

cold, heat or direct sunlight. Do not put the

product close to a heating source.

Batteries should not be exposed to

excessive heat such as bright sunshine

or fire.

Make sure the baby unit(s) and the adapter

cord(s) are always out of reach of the baby,

at least 3 feet away from the baby or crib, to

avoid a possible strangulation hazard.

Never place the baby unit(s) inside the

baby’s crib or playpen. Never cover the

baby unit(s) or parent unit with anything

such as a towel or a blanket.

Other electronic products may cause

interference with your baby monitor. Try

installing your baby monitor as far away

from these electronic devices as possible:

wireless routers, radios, cellular telephones,

intercoms, room monitors, televisions,

personal computers, kitchen appliances and

cordless telephones.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless devices):

Wireless Technology Research, LLC (WTR),

an independent research entity, led a

multidisciplinary evaluation of the interference

between portable wireless devices and

implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

Should keep wireless devices at least six

inches from the pacemaker.

Should NOT place wireless devices directly

over the pacemaker, such as in a breast

pocket, when it is turned ON.

WTR’s evaluation did not identify any risk

to bystanders with pacemakers from other

persons using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards

regarding electromagnetic fields (EMF).

If handled properly and according to the

instructions in this user’s manual, the product

is safe to be used based on scientific evidence

available today.

•

Avis aux détenteurs de stimulateurs cardiaques

Vous devriez maintenir les dispositifs sans fil à au

moins six pouces du simulateur cardiaque.

Ils ne doivent PAS placer le téléphone sans fil

directement sur le stimulateur cardiaque, tel que

dans une poche de chemise, lorsque celui-ci est

en marche.

L’étude effectuée par l’organisme WRS n’a pas

identifié de risque pour les détenteurs de simulateurs

cardiaques causés par les gens qui utilisent

dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes

les normes se rapportant aux champs

électromagnétiques (EMF) standard. Si vous le

manipulez correctement en suivant les instructions

de ce guide, son utilisation sera sécuritaire pendant

de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons

aujourd’hui.

•

To keep this product working well and looking good,

follow these guidelines:

Avoid putting it near heating appliances and devices

that generate electrical noise (for example, motors or

fluorescent lamps).

DO NOT expose it to direct sunlight or moisture.

Avoid dropping the product or treating it roughly.

Clean with a soft cloth.

DO NOT immerse the parent unit and the baby unit

in water and do not clean them under the tap.

DO NOT use cleaning spray or liquid cleaners.

Make sure the baby unit and parent unit are dry

before you connect them to the mains again.

•

General product care The POWER

light on the

baby unit

flashes and

the parent

unit displays

The baby unit is unpaired from the

parent unit.

Pair the baby unit:

Press MENU/SELECT when

the parent unit is not in use.

Press or to choose .

Press or to choose a

desired baby unit slot, then

press MENU/SELECT. The

screen displays .

Turn on the baby unit, and then

immediately press and hold

PAIR until the POWER light

turns on.

When pairing is successful, the

screen displays , and then the

image from the newly paired baby

unit.

If pairing fails, the screen

displays . Try the pairing

process again.

Only one baby unit can be

paired at a time.

•

Why does

the parent

unit react too

quickly to

other sounds?

The baby unit also detects other

sounds than those of your baby.

Adjust the sensitivity level to a

lower level or adjust the speaker

volume on the parent unit.

Why don’t I

hear a sound/

Why can’t I

hear my baby

cry?

The volume of the parent unit may

have set too low. Press / VOL+

to increase the volume level.

You may have set a low sound

sensitivity level. See Adjust the

sound sensitivity of the baby

unit to change the setting.

Why does the

parent unit

beep?

The baby units may be out of

range. Move the parent unit closer

to the baby units (but not less than

3 feet).

If the parent unit is powered by the

provided battery, it may not have

enough charge for the parent unit

to perform normally. Charge the

battery in the parent unit for up to

12 hours.

Why can’t I

establish a

connection?

Why is the

connection

lost every

now and

then? Why

are there

sound

interruptions?

The baby units may be out of

range. Move the parent unit closer

to the baby units (but not less than

3 feet).

Other electronic products may

cause interference with your baby

monitor. Try installing your baby

monitor as far away from these

electronic devices as possible.

VTech VM511 Manuel utilisateur

Marque: VTech

Modèle: VM511

Catégorie: Babyphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech VM511 User manual

VTech VM511 Manuel utilisateur

VTech VM511 Manuel utilisateur

dans d''autres langues

Documents connexes