Nice TITAN12L Manuel utilisateur

Marque: Nice

Modèle: TITAN12L

Catégorie: Ouvre-porte

Taper: Manuel utilisateur

Ce manuel convient également à

TITAN12L1

Revision 8.0 December, 2018

Part #10001700

Nice Swing Gate

Actuator

Vehicular Swing Gate Actuator

TITAN12L

936 Control Board

TITAN12L1

1050 Control Board

CBOX with 1050 control board

CBOX with 936 control board

912L

Programming & controls, connections and safety

information provided in the 1550/1551 manuals in CBOX

www.hysecurity.com iii

1 - Overview 4

2 - General Safety Information 7

3 - Use of Vehicle Detectors 10

4 - Gate Construction and Safety 10

5 - Maintenance of Gate Systems 12

6 - Entrapment Protection 13

7 - Compatible External Sensors 14

8 - 936 Circuit Board Layout 15

9 - 1050 Circuit Board Layout 16

10 INSTALLATION PROCEDURES 17

10.1 -Pivot Arm Installation 17

FIGURE 10 - 1 Pull to Open Installation 17

FIGURE 10 - 2 Vertical Pivot Position 17

10.2 - Push to Open installation 18

FIGURE 10 - 3 Push to Open Installation 18

10.3 - Actuator Mounting 18

FIGURE 10 - 4 Actuator Mounting 18

FIGURE 10 - 5 Gate Bracket Mounting 18

10.4 - Manual Release/Manual Operation 19

FIGURE 10 - 6 Manual Release Disengage 19

FIGURE 10 - 7 Manual Release Re-engage 19

10.5 - TITAN12L/12L1 Actuator Wiring 20

FIGURE 10 - 8 Manual Release Handle 20

FIGURE 10 - 9 Wire Harness Insertion 20

FIGURE 10 - 10 TITAN12L/12L1 Actuator Wiring 20

10.6 - 936 Control Board Wiring 21

10.6.1 - TITAN ACTUATOR WIRING (PULL TO OPEN) 21

10.6.2 - TITAN ACTUATOR WIRING (PUSH TO OPEN) 21

10.7 - 1050 Control Board Wiring (Single Gate Application) 22

10.7.1 - TITAN ACTUATOR WIRING (PULL TO OPEN) 22

10.7.2 - TITAN ACTUATOR WIRING (PUSH TO OPEN) 22

10.8 - 936 & 1050 Limit & Motor Connection to Board 23

10.8.1 - 936 Control Board 23

10.8.2 - 1050 Board 23

10.9- Limit switch adjustment 24

FIGURE 10 - 13 Limit Switch Adjustment 24

FIGURE 10 - 14 Limit LED Location 1050 Control Board 24

FIGURE 10 - 15 Limit LED Location 936 Control Board 24

11 GENERAL LAYOUT AND SAFETY ACCESS 25

FIGURE 11 - 1 Layout for In-Ground Loops 25

FIGURE 11 - 2 Layout for Photocells 25

12 ACCESSORIES AND SENSORS 26

13 INSPECTION AND OPERATION 25

14 EMERGENCY VEHICLE ACCESS 25

15 Maintenance Schedule 26

16 Troubleshooting 26-27

17 Appendix - French Translations 28-31

TABLE OF CONTENTS

4 www.hysecurity.com

1. Overview

Congratulations on selecting a Nice gate operator for automating your gate system. With proper

selection, system design, installation and maintenance this operator should provide years of reliable

operation.

This manual covers the following Nice operator models: Titan 12L and Titan 12L1.

1.1 TITAN12L/12L1 Swing Gate Actuator

This manual provides documentation that covers the layout, construction, mechanical and electrical

installation of TITAN12L/12L1 swing gate operators with the Nice brand 936 or 1050 control board.

TITAN12L/12L1 swing gate operators are intended for residential gate installations only. Please consult

your Nice distributor or Nice Dealer/Installer for more information regarding installations or questions

not speciﬁ cally covered in this manual.

The TITAN12L/12L1 swing gate actuator is the foundation for the next generation of easily installed,

conﬁ gured and maintained swing gate operators from Nice. This Actuator has a maximum gate capacity

of 600 lb for a 20 ft leaf or 1000 lb for an 8 ft leaf. Operator has a key lockable manual release, easily

accessible limit switch settings and is easy to maintain or repair in-the-ﬁ eld. The TITAN12L/12L1 gives

dealers, installers and homeowners the ability to take control of their access and security systems. This

actuator includes a 2-year factory warranty against manufacturing defects and lifetime customer support.

1.2 Product Speciﬁ cations

Model TITAN12L+(12VDC)

Gate Specs

up to 600 lb for a 20 ft leaf

(272 kg for 6 m)

up to 1000 lb for an 8 ft leaf

(453 kg for 2.4 m)

Open/Close Time (to

90°) 14-16 seconds

Maximum Degree of

Opening 120°

Solar Compatible Yes

Manual Release w/ Key-

lock Yes

Motor Encoder Yes

Easily Positioned Limit

Switches Yes

Drive Mechanism Stainless Steel Screw

Operating Temperature -4º to 122º F (-20º to 50º C)

912L Actuator Weight 19.75 lb (8.96 kg)

Dimensions - Fully

Retracted

43(L) x 4(W) x 6.75 inches (D)

(109.2(L) x 10(W) x 17.5 cm (D)

Push to Open Installation Yes

Pull to Open Installation Yes

UL 325 Certiﬁ ed/Listed Usage Class I, II, III, IV

1.3 What is Included

P/N Name Note

CBOX1050 Control Box/1050

Control Board

Paired w/ 912L

Actuator to make

TITAN12L System

CBOX936 Control Box/936

Control Board

Paired w/912L1

Actuator to make

TITAN121 System

912L Actuator with 12’

harness

Used in both

TITAN12L/12L1

System

OXI/A Opera Receiver

433Mhz

Included in

CBOX936/1050 Box

#1116 Pivot Arm Included in Actuator

Box

#10025215 Gate Attach Bracket Included in Actuator

Box

#1125 Bolt Kit Included in Actuator

Box

ABF/A Directional antenna

433 khz kit

Accessory sold

separately.

www.hysecurity.com 5

1.4 936 Control Board

The 936 control board is housed in a protective

plastic enclosure that includes two 7-segment

LEDs, ﬁ ve dedicated programming buttons and

three buttons for navigation of the setup and

programming menus, as well as 3 buttons for

open, close, and stop. Connectors for power, input

and output peripherals are arranged around the

edges of the board and clearly labeled. A plug-

in connector is provided for direct installation of

a Nice-brand receiver which can be associated

with up to 1000 remote controls. Connectors for

other Nice-brand plug-in accessories include the

2-wire Bluebus photocells for external entrapment

protection. Dry contact inputs are provided for

loop, probe, and photoelectric detectors as well as

guard station inputs and ﬁ re department control.

Voltage outputs (+12VDC and +24VDC) are

available to power other safety and entrapment-

prevention devices, along with a solenoid lock

output.

The 936 control board accepts DC input voltage

ranging from +10VDC to +35VDC with input

polarity protection on the main input and the solar

charge input. All settings are stored in non-volatile

memory that is protected from power outages.

Programmable slowdown position. Built-in current

sensing provides inherent gate force monitoring

and limiting for safety. The “Learn” function helps

the gate installer conﬁ gure the 936 control board

semi-automatically for optimum settings of gate

opening and closing speeds.

1.5 936 Main Control Board Speciﬁ cs

Inputs for solar panels and batteries.

Motor outputs for two motors.

Low power consumption in stand-by mode.



Built-in charge regulator to maintain battery

charge.

Socket for plug-in Nice receiver.



Easy setup with 7-segment LEDs and dedicated

buttons.



Setup and learning stored in onboard memory.



Digital programming for auto-close timing,

force, speed, and opening delay.



On-board buttons for operating the gate (Open,

Close, Stop)



Inputs for guard station, additional third party

receivers, loop detectors, Fire, and UL/Edge

signals.

Two relay outputs (not programmable).



Surge suppression on every peripheral input

and output, up to 1200A.



Bluebus port for Nice plug-in, self-monitored,

entrapment protection devices.



USB port and bootloader for easy software

updates.



Motor bypass connectors for rapid

troubleshooting an actuator and positioning

a gate.

6 www.hysecurity.com

1.6 1050 Control Board

The 1050 main control board is housed in a

protective plastic enclosure that includes a 2-line

LCD and with 5 dedicated buttons and 3 buttons

for navigation of the setup, programming, and

information menus, as well as 3 buttons for open,

close, and stop. Connectors for power, inputs,

and output peripherals are arranged around the

edges of the board and clearly labeled. A plug-in

connector is provided for direct installation of a

Nice-brand receiver which can be controlled by up

to 1000 transmitters. A recessed RJ-11 jack offers a

connection to an optional O-view programmer with

Bluetooth and O-View programmer and optional

Bluetooth module that can be programmed via

PC. Connectors for other Nice-brand plug in

accessories include 2-wire Bluebus, self-monitored

photocells for entrapment protection. Dry

contact inputs are provided for loop, probe, and

photoelectric detectors, as well as guard station

and ﬁ re department control of gate opening and

closing. Voltage outputs (+12VDC and +24VDC)

are also made available to power safety and

entrapment-prevention devices, and a magnetic

lock if required. On board charge control circuitry

delivers reliable power to a backup battery (if

installed) and the unit is equipped with input for

a solar panel for self-powered installations.

The 1050 main control board accepts DC input

voltage ranging from 10VDC to 35VDC. A 2-line

LCD with dedicated buttons allows installer to

quickly program the 1050 when changes to its

factory-default settings need to be made. A real

time clock/calendar enables programming for

scheduled weekly or daily events like opening,

closing, or locking the gate. Gate opening and

closing speed, acceleration, soft-start settings,

and reversing speed may be set to factory

default settings, or individually programmed per

customized gate installation requirements. Built-

in current sensing enables inherent gate force

monitoring and limiting for safety and an on board

alarm indicates when two sequential obstructions

have been sensed in either direction. The “Learn”

function helps the gate installer conﬁ gure the 1050

control board semi-automatically for optimum

settings of gate opening and closing speeds,

with simple programmable adjustments to force

and speed settings that may be made with the

programming button on the control panel.

1.7 1050 Main Control Board Speciﬁ cs



Inputs for solar panel and batteries, and Main

DC Power.

Low power consumption in stand-by mode.



Built-in regulator to keep the battery charged

(either through solar or Main DC power).

Socket for plug-in Nice receiver.



Board compatible with Nice Opera System

(facilitates programming and diagnostic’s away

from the site of installation). Requires optional

O-View and OVBT (Bluetooth) module.



Easy programming with LCD display and

dedicated buttons.



Digital programming for auto-close, force,

speed, opening delay.



On board buttons for operating the gate (Open,

Close, Stop).



Built-in voltmeter to check input voltage, battery

voltage, solar panel volt age, motors’ current.



Temperature sensor to optimize charging

battery and system performance.

Programmable service alarm.



2 Programmable timers (from 1 sec to 9 hours).



Inputs for guard station, additional third party

receivers, loop detectors, FIRE and UL/Edge

signals.



2 programmable inputs (open, close, step, mid-

position, hold to open, hold to close, activating

timer).



Surge suppression on every peripheral input

(digital and analog).



Ports for self-powered Nice plug-in peripherals.

(BlueBus).

www.hysecurity.com 7

1.8 The installation of this product is not a “do-

it-yourself” project. A qualiﬁ ed gate operator

installation company should be contacted

to install the gate operator to ensure a safe

and reliable installation. Since many aspects

of gate system installation are under the

control of the installer, it is the responsibility

of the property owner to ensure the installer

is qualiﬁ ed to carry out the installation in a

safe and professional manner.

1.9 Consult local government agencies for

up-to-date rules and regulations as certain

municipalities have established licensing,

codes or regulations that regulate automated

gate system design and installation.

2. General Safety Information

A gate operator is only a component in a gate

system. The other parts of the gate system

can include the gate, the external entrapment

sensors, access controls, and vehicle detectors.

To have a gate system that provides safety,

security, and reliable operation it is essential these

components operate together as a system. It is

the responsibility of the system designer and/or

installer to ensure any safety or operational issues

have been addressed.

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS.

Never let children operate or play with gate

controls. Keep the remote control away from

children.

Always keep people and objects away from

the gate. NO ONE SHOULD CROSS THE

PATH OF THE MOVING GATE.

Test the gate operator monthly. The gate

MUST reverse on contact with a rigid

object or stop when an object activates the

non-contact sensors. After adjusting the

force or the limit of travel, retest the gate

operator. Failure to adjust and retest the

gate operator properly can increase the risk

of injury or death.

Use the emergency release only when the

gate is not moving.

KEEP GATES PROPERLY MAINTAINED. Read

the user’s manual. Have a qualiﬁ ed service

person make repairs to gate hardware.

The entrance is for vehicles only. Pedestrians

must use separate entrance.

8. SAVE THESE INSTRUCTIONS.

WARNING

To reduce the risk of injury or death.

8 www.hysecurity.com

2.1 UL325 Usage Classes

The UL325 standard covers gate operators. Within

this safety standard several Usage Classes are

described that deﬁ ne different types of installations

where gate operators can be applied. Some

operators are restricted in their usage application.

All Nice USA operators are approved for use in

all four UL325 Usage Classes. Appropriate Usage

Classes are shown in the Speciﬁ cations.

2.1.1 Class I Residential Gate Operator. Intended

for use in a location of one to four single

family dwellings or a parking area associated

with one to four single family dwellings.

2.1.2 Class II Commercial / General Access Gate

Operator. Intended for use in a commercial

location or building such as a multi-family

housing units (ﬁ ve or more single family

units) hotels, garages, retail stores or other

buildings servicing general public.

2.1.3 Class III Industrial / Limited Access Gate

Operator. Intended for use in an industrial

location or building such as factories

or loading docks or other locations not

intended to service general public.

2.1.4

Class IV Restricted Access Gate Operator.

Intended for use in guarded industrial

locations or buildings such as an airport

security area or other restricted access

location, not servicing general public,

in which access is monitored by security

personnel or via closed circuitry.

www.hysecurity.com 9

2.2 Vehicular Trafﬁ c Only

This automatic gate operator is not designed nor

is it intended for pedestrian trafﬁ c. Vehicular gate

operators must by their nature be powerful to

function reliably. This power can cause injury or

death. Accordingly, direct all pedestrian trafﬁ c to

a separate walk-through gate.

2.3 Install This Gate Operator Only When:

a. The operator is appropriate for the

construction of the gate and the usage Class

of the gate,

b. All openings of a horizontal slide gate are

guarded or screened from the bottom of the

gate to a minimum of 1.83 m (6 ft) above the

ground to prevent a 57.2 mm (2-1/4 inch)

diameter sphere from passing through the

openings anywhere in the gate, and the

portion of the adjacent fence that the gate

covers in the open position,

c. All exposed pinch points are eliminated or

guarded, and

d. Guarding is supplied for exposed rollers.

e. When utilizing a Nice 936 board and 1050

board and 8 sensors may be connected.

2.4 The operator is intended for installation only

on gates used for vehicles. Pedestrians must

be supplied with a separate access opening.

The pedestrian access opening shall be

designed to promote pedestrian usage.

Locate the gate such that persons will not

come in contact with the vehicular gate during

the entire path of travel of the vehicular gate.

2.5 The gate must be installed in a location so

that enough clearance is supplied between

the gate and adjacent structures when

opening and closing to reduce entrapment

risk. Swinging gates shall not open into public

access areas

2.6 The gate must be properly installed and work

freely in both directions prior to gate operator

installation. Do not ochange operator settings

to compensate for an improperly installed,

improperly functioning, or damaged gate.

2.7

Permanently mounted controls intended for

user activation must be located at least 1.83

m (6 ft) away from any moving part of the gate

and where the user is prevented from reaching

over, under, around or through the gate to

operate the controls. Exception: Emergency

access controls only accessible by authorized

personnel (e.g. fire, police, EMS) may be

placed at any location in the line-of-sight of

the gate.

2.8

The Stop and/or Reset button must be located

in the line-of-sight of the gate. Activation of

the reset control shall not cause the operator

to start.

2.9

A minimum of two (2) WARNING SIGNS shall

be installed, in the area of the gate. Each

placard is to be visible by persons located

on the side of the gate on which the placard

is installed.

2.10

For gate operators utilizing a non-contact

sensor (Photo Eye):

See instructions on the placement of non-

contact sensors for each Type of application,

Care shall be exercised to reduce the risk

of nuisance tripping, such as when a vehicle,

trips the sensor while the gate is still moving,

and

One or more non-contact sensors shall

be located where the risk of entrapment or

obstruction exists, such as the perimeter

reachable by a moving gate or barrier.

10 www.hysecurity.com

2.11 For a gate operator utilizing a contact

sensor (Edge):

a. One or more contact sensors shall be

located where the risk of entrapment or

obstruction exists, such as at the leading

edge, trailing edge, and postmounted both

inside and outside of a vehicular horizontal

slide gate.

b. A hardwired contact sensor shall be

located and its wiring arranged so that the

communication between the sensor and the

gate operator is not subjected to mechanical

damage.

c. A wireless device such as one that transmits

radio frequency (RF) signals to the gate

operator for entrapment protection functions

shall be located where the transmission of

the signals are not obstructed or impeded

by building structures, natural landscaping

or similar obstruction. A wireless device

shall function under the intended end-use

conditions.

d. One or more contact sensors shall be

located on the inside and outside leading

edge of a swing gate. Additionally, if the

bottom edge of a swing gate is greater than

152 mm (6 in) but less than 406 mm (16 in)

above the ground at any point in its arc of

travel, one or more contact sensors shall be

located on the bottom edge.

Use of Vehicle Detectors

Use of vehicle detectors (loop detectors) is strongly

encouraged to prevent damage to vehicles

caused by gates closing on them. This is not

considered to be a safety item as vehicle detectors

cannot provide protection to pedestrians. In some

situations, photoelectric devices may be used as

vehicle detectors, but should be wired accordingly.

4. Gate Construction and Safety

Gate construction plays a very important role in

ensuring the safety of any automated gate system.

The standard for gate construction is ASTM F2200.

Below are key areas to address safety in gate

design. For complete information consult the

standard. Copies of the standard are available at:

https://www.astm.org/Standards/F2200.htm

Another source of information is available

from DASMA, the Door and Access System

Manufacturer’s Association. The Association

publishes Technical Data Sheets, one of which

concerns ASTM F2200. For more information, see:

http://www.dasma.com/PDF/Publications/

TechDataSheets/OperatorElectronics/TDS370.pdf

4.1 General Requirements for gate construction

4.1.1

Gates shall be constructed in accordance

with the provisions given for the appropriate

gate type listed. Refer to ASTM F2200 for

additional gate types.

4.1.2

Gates shall be designed, constructed

and installed to not fall over more than 45

degrees from the vertical plane, when a gate

is detached from the supporting hardware.

4.1.3

Gates shall have smooth bottom edges,

with vertical bottom edged protrusions not

exceeding 0.50 in. (12.7 mm) when other

than the Exceptions listed ASTM F2200.

4.1.4

The minimum height for barbed wire shall

not be less than 6 ft. (1.83 m) above grade.

The minimum height for barbed tape shall

not be less than 8 ft. (2.44 m) above grade.

4.1.5

An existing gate latch shall be disabled

when a manually operated gate is retroﬁtted

4.1.6

A gate latch shall not be installed on an

automatically operated gate.

4.1.7

Protrusions shall not be permitted on any

gate. Consult ASTM F2200 for exceptions.

www.hysecurity.com 11

4.1.8 Gates shall be designed, constructed and

installed such that their movement shall not

be initiated by gravity when an automatic

operator is disconnected.

4.1.9 For pedestrian access in the vicinity of

an automated vehicular gate, a separate

pedestrian gate shall be provided. The

pedestrian gate shall be installed in a

location such that a pedestrian shall not

come in contact with a moving vehicular

access gate. A pedestrian gate shall not be

incorporated into an automated vehicular

gate panel.

4.1.10 Any non-automated gate that is to

be automated shall be upgraded to conform

to the provisions of this speciﬁcation.

4.1.11 This speciﬁcation shall not apply to

gates generally used for pedestrian access

and to vehicular gates not to be automated.

4.1.12 Any existing automated gate, when

the operator requires replacement, shall be

upgraded to conform to the provisions of

this speciﬁcation in effect at that time.

4.2 Vehicular Horizontal Slide Gate Requirements

4.2.1 The following provisions shall apply

to Class I, Class II and Class III vehicular

horizontal slide gates:

4.2.1.1 All weight bearing exposed rollers

8 ft (2.44 m), or less, above grade shall be

guarded or covered

4.2.1.2 All openings shall be designed,

guarded, or screened from the bottom

of the gate to the top of the gate or a

minimum of 72 in. (1.83 m) above grade,

whichever is less, to prevent a 2 1/4 in. (57

mm) diameter sphere from passing through

the openings anywhere in the gate, and in

that portion of the adjacent fence that the

gate covers in the open position. The gate

panel shall include the entire section of the

moving gate, including any back frame or

counterbalance portion of the gate.

4.2.1.3 A gap, measured in the horizontal

plane parallel to the roadway, between

a ﬁxed stationary object nearest the

roadway (such as a gate support post) and

the gate frame when the gate is in either

the fully open position or the fully closed

position, shall not exceed 2 1/4 in. (57 mm).

Exception: All other ﬁxed stationary objects

greater than 16 in. (406 mm) from the gate

frame shall not be required to comply with

this section.

4.2.1.4

Positive stops shall be required to

limit travel to the designed fully open and

fully closed positions. These stops shall

be installed at either the top of the gate,

or at the bottom of the gate where such

stops shall horizontally or vertically project

no more than is required to perform their

intended function.

4.2.1.5

All gates shall be designed with

sufﬁ cient lateral stability to assure that the

gate will enter a receiver guide. Consult

ASTM F2200 for details on various gate

panel types.

4.2.2

The following provisions shall apply to

Class IV vehicular horizontal slide gates:

4.2.2.1

All weight bearing exposed rollers

8 ft (2.44 m), or less, above grade shall be

guarded or covered.

4.2.2.2

Positive stops shall be required to

limit travel to the designed fully open and

fully closed positions. These stops shall

be installed at either the top of the gate,

or at the bottom of the gate where such

stops shall horizontally or vertically project

no more than is required to perform their

intended function.

12 www.hysecurity.com

4.3 Vehicular Horizontal Swing Gates

4.3.1 The following provisions shall apply to

Class I, Class II, and Class III horizontal swing

gates:

4.3.2 Gates shall be designed, constructed and

installed so as not to create an entrapment

area between the gate and the supporting

structure or other ﬁxed object when the

gate moves toward the fully open position,

subject to the following provisions.

4.3.3 The width of an object (such as a wall, pillar

or column) covered by a swing gate when

in the open position shall not exceed 4 in.

(102 mm), measured from the centerline of

the pivot point of the gate. Exception: For

a gate that is not in compliance with this

provision, the deﬁned area shall be subject

to the entrapment protection provisions of

UL 325.

4.3.4 Except for the zone speciﬁed in 4.3.3 the

distance between a ﬁxed object such as

a wall, pillar or column, and a swing gate

when in the open position shall not be less

than 16 in. (406 mm). Exception: For a gate

that is not in compliance with this provision,

the deﬁned area shall be subject to the

entrapment protection provisions of UL 325.

4.3.5 Class IV vehicular horizontal swing

gates shall be designed, constructed and

installed in accordance with security related

parameters speciﬁc to the application in

question.

5. Maintenance of Gate Systems

To keep your automated gate system performing

both safely and reliably it is important to ensure

that the components of that system are functioning

properly. At least monthly:

5.1

Disconnect the gate operator and manually

move the gate through its range of travel.

Note any squeaks from rollers or hinges or

areas of binding. The gate should travel

smoothly and quietly throughout its range.

If it does not, contact a gate professional to

correct the problem.

5.2

Reconnect the gate operator and perform the

following tests:

5.2.1

With the gate opening, block any photo

eyes and/or depress any safety edges used

to protect the open direction. The gate

should stop, or, stop and reverse.

5.2.2

With the gate closing, block any photo

eyes and/or depress any safety edges used

to protect the close direction. The gate

should stop, or, stop and reverse.

5.2.3

Using a suitable obstruction in the path of

the gate (a solid, immovable object), run the

gate in the open direction until it contacts

the obstruction. The gate should stop and

reverse.

5.2.4

Using a suitable obstruction in the path of

the gate (a solid, immovable object), run the

gate in the close direction until it contacts

the obstruction. The gate should stop, or,

stop and reverse.

www.hysecurity.com 13

6. Entrapment Protection

The UL325 standard for gate operators requires

a minimum of two independent entrapment

protection means for each entrapment zone. An

entrapment zone is deﬁ ned as follows:

For slide gates, any locations between a moving

gate and a counter opposing edge or surface

where entrapment is possible up to a height of 6

ft. (1.83m) above grade. Such locations occur if at

any point in travel the gap between a moving gate

and the ﬁ xed counter opposing edges or surfaces

is less than 16 in. (406mm).

For swing gates, locations between a moving

gate or moving, exposed operator components

and a counter opposing edge or surface where

entrapment is possible up to 6 ft (1.83m) above

grade. Such locations occur if during any point

in travel:

a. The gap between the bottom of a moving

gate and the ground is greater than 4 in.

(101.6 mm) and less than 16 in. (406 mm); or

The distance between the center line of the

pivot and the end of the wall, pillar, or column

to which it is mounted when in the open or

closed position exceeds 4 in. (101.6 mm).

Any other gap between a moving gate and

ﬁ xed counter opposing edges or surfaces

or other ﬁ xed objects is less than 16 in. (406

mm) (examples are walls, curbs, berms or

other immovable objects).

Potential entrapment zones are shown in Figure 1

for slide and swing gates, but keep in mind there

may be other entrapment zones presented by

the actual installation and adjacent structures or

landscape that must be protected as well.

Entrapment Protection Inputs - Typical Installation Diagram Utilizing Photocells

Outside

Gate

Close Direction Eye

Open

Direction

Eye

Open

Direction

Eye

(Possible Entrapment Zone

if gate opens to <16 inches

from wall or ﬁxed object)

(Possible Entrapment Zone

if gate opens to <16 inches

from wall or ﬁxed object)

14 www.hysecurity.com

All Nice gate operators feature an Inherent

Entrapment System (IES) (UL325 Type A) that

monitors the force on the gate during travel.

This system protects in both the open and

close direction and reverses on contact with an

obstruction. This IES system serves as one of the

means of entrapment protection.

External sensors must be used to protect against

entrapment at each location where an entrapment

zone exists. The minimum number of external

sensors required to enable automatic operation

of the gate operator is as follows:



Swing Gates: One sensor in the Close direction

(provided the gate in the open direction

presents no risk of entrapment.)



Slide Gates: One sensor in the Open direction

and one sensor in the Close direction.

The gate operator tests for the presence of these

sensors, and if the required minimum number

is not found, the operator will only run using

continuous pressure on an Open/Close button,

either on the controller, or an external device.

7. Compatible External Sensors

Only the following external sensors have been

evaluated and tested with Nice gate systems and

are approved to be used for protection against

entrapment:

Nice Through-Beam Photo Eye BlueBus

EMX IRB-RET Retro-reﬂ ective Photo Eye

ASO Sentir Series Contact Edge

Miller Edge GEM-103 Edge Sensor Converter



EMX WEL-200 Wireless Edge Transmitter/

Receiver

www.hysecurity.com 15

8 - 936 CIRCUIT BOARD LAYOUT

LEARN BUTTON

PROGRAM BUTTONS

DUAL 7 SEGMENT STATUS

DISPLAY WINDOW

PROGRAM MENU

CONTROL BUTTONS

GATE OPERATION

CONTROL BUTTONS

ACCESSORY POWER

OUTPUTS

POWER INPUT

CONNECTIONS

MOTOR CONTROLS

30A

EARTH GROUND

CONNECTION

ACCESSORY

POWER OUTPUTS and

PROGRAMMABLE INPUT

“C”

ACCESSORY

POWER OUTPUT

AND STEP INPUT

ACCESSORY

POWER OUTPUT

AND PROGRAMMABLE

INPUT A

INPUTS

16 www.hysecurity.com

9 - 1050 CIRCUIT BOARD LAYOUT

MAIN DC POWER 30A FUSE MOTOR

SERIES 1050

MOTOR 2

BATTERYSOLAR P.

OXI/A Receiver

UL325 Compliant Monitored Safety Devices(s) required.

Accessory

Output

Connections

Power Input

Connections

Motor Output

Connections

BlueBus

Connection

Primary / Secondary

Connection

Accessory Input Connections

Earth Ground

www.hysecurity.com 17

Center of Hinge Center of Hinge

10 - INSTALLATION PROCEDURES

10.1 - Pivot Arm Installation

IMPORTANT - Never weld parts to the gate or posts when the operator circuit board is powered. Doing so may

damage the board beyond repair.

PULL TO OPEN INSTALLATION - Location of Pivot Point

The following instructions provide up to 105° of swing.

Measurements are taken from the center of pivot of the gate hinge.

The pivot arm needs to be securely mounted to the hinge post or equivalent mounting surface. It is recommended to weld the

pivot arm to a metal post. In order to achieve the correct articulation, geometry and rate of speed of the gate it is critical that

the measurements below are followed. The pivot arm may need to be cut to achieve the correct placement of the actuator

mounting hole. Measurements are taken from the center of pivot of the gate hinge.

NOTE: If you have columns built around your gate hinge post, check these measurements for proper clearance before

proceeding with this pull to open installation.

LEFT HAND SWING RIGHT HAND SWING

GATE CLOSED

DIRECTION OF OPENING

OVERHEAD VIEW

FIGURE 10 - 1 PULL TO OPEN INSTALLATION

Center line of

attachment point for

gate bracket

Hinge Post

SIDE VIEW

Vertical position of pivot arm

The top edge of the Pivot Arm will be located 1/2

inch below the center line for the gate bracket. The

Pivot Arm must be level when secured.

FIGURE 10 - 2 VERTICAL PIVOT POSITION

18 www.hysecurity.com

10.2 - Push to Open Installation

PIVOT ARM INSTALLATION - Location of Pivot Point

Measurements are taken from the center of pivot of the gate hinge.

The pivot arm needs to be securely mounted to the hinge post or equivalent mounting surface. It is recommended to weld the

pivot arm to a metal post. In order to achieve the correct articulation, geometry and rate of speed of the gate it is critical that

the measurements below are followed. The pivot arm may need to be cut to achieve the correct placement of the actuator

mounting hole. Measurements are taken from the center of pivot of the gate hinge.

DIRECTION OF OPENING

GATES CLOSED

HINGE POST HINGE POST

LEFT HAND SWING RIGHT HAND SWING

TOP VIEW

6”

11”

6”

11”

FIGURE 10 - 3 PUSH TO OPEN INSTALLATION

10.3 - Actuator mounting

Mount the actuator to the pivot arm as shown.

The lock nut should be snug to prevent movement or shifting

when the actuator is running. This will also prevent excessive

“bounce” or “wobble” when the gate stops moving.

or Pin

with

Clip

FIGURE 10 - 4 ACTUATOR MOUNTING

FIGURE 10 - 5 GATE BRACKET MOUNTING

10 - INSTALLATION PROCEDURES (CONT.)

www.hysecurity.com 19

10.4 - Manual Release / Manual Operation

MANUAL RELEASE DISENGAGE

1. Lift rubber key cover, insert key into lock, and rotate 90° clockwise.

2. Lift handle

3. Actuator is now Disengaged (manual operation is possible).

NOTE: Manual operation may be prevented if the actuator is fully retracted.

FIGURE 10-6 MANUAL RELEASE DISENGAGE

FIGURE 10-7 MANUAL RELEASE RE-ENGAGE

MANUAL RELEASE RE-ENGAGE

1. Close handle.

2. Rotate key 90° counter-clockwise and remove key.

3. Replace rubber key cover.

4. Operator is now re-engaged in Automatic Mode (manual

operation is not possible).

10 - INSTALLATION PROCEDURES (CONT.)

20 www.hysecurity.com

10.5 - TITAN12L Actuator Wiring

Using the supplied key, unlock the manual release handle. Lift upwards on the release handle as shown.

FIGURE 10 - 8 MANUAL RELEASE HANDLE

With the release handle up, remove the screws from the limit cover and remove the cover. On the bottom of the actuator

loosen the strain relief nut and insert the wire into the actuator housing. The connections are on the top of the actuator

behind the limit assembly.

Terminal block

for harness

connections

Connect the wiring to the actuator

terminal block as shown.

THE FOLLOWING SECTION NEED ONLY BE USED FOR REWIRNG IN THE EVENT OF A DESIRED

LONGER OR SHORTER CABLE LENGTH.

FIGURE 10 - 9 WIRE HARNESS INSERTION

FIGURE 10 - 10 TITAN12L/12L1 ACTUATOR WIRING

10 - INSTALLATION PROCEDURES (CONT.)

La page charge ...

Nice TITAN12L Manuel utilisateur

Marque: Nice

Modèle: TITAN12L

Catégorie: Ouvre-porte

Taper: Manuel utilisateur

Ce manuel convient également à

TITAN12L1

Télécharger le PDF

rapport

dans d''autres langues

English: Nice TITAN12L User manual

Nice TITAN12L Manuel utilisateur

Ce manuel convient également à

Nice TITAN12L Manuel utilisateur

dans d''autres langues

Autres documents