Fronius TS 65A-3 Mode d'emploi

Marque: Fronius

Modèle: TS 65A-3

Taper: Mode d'emploi

/ Perfect Welding / Solar Energy / Perfect Charging

QUICK START GUIDE

Fronius Smart Meter TS 65A-3

42,0410,2496 006-22042021 FRONIUS INTERNATIONAL GMBH www.fronius.com

DE: WARNUNG! Fehlbedienung und fehlerhaft durchgeführte Arbeiten können schwerwiegende Personen- oder

Sachschäden verursachen. Die Installation und Inbetriebnahme des Smart Meters darf nur durch geschultes Personal und

nur im Rahmen der technischen Bestimmungen erfolgen. Vor Arbeiten mit dem Gerät, alle beiliegenden, aufgedruckten

und online zur Verfügung gestellten Dokumente lesen und verstehen! Dieses Dokument beschreibt nicht alle möglichen

Systemkongurationen.

EN: WARNING! Incorrect operation and incorrectly performed work can cause serious personal injury or material damage. The Fronius

Smart Meter may only be installed and commissioned by trained personnel and only within the scope of the technical regulations. Befo-

re working with the device, read and understand all enclosed, printed and online documents! This document does not describe all of the

possible system congurations.

FR: AVERTISSEMENT ! Une mauvaise utilisation et un travail mal eectué peuvent causer des blessures graves ou des dommages

matériels. Le Fronius Smart Meter ne peut être installé et mis en service que par du personnel formé et uniquement dans le cadre des

réglementations techniques. Avant de travailler avec l’appareil, lisez et comprenez tous les documents ci-joints, imprimés et en ligne ! Ce

document ne décrit pas toutes les congurations possibles du système.

IT: ATTENZIONE! Un funzionamento non corretto e un lavoro eseguito in modo non corretto possono causare gravi lesioni personali o

danni materiali. Lo Fronius Smart Meter può essere installato e messo in funzione solo da personale addestrato e solo nell’ambito delle

norme tecniche. Prima di lavorare con l’apparecchio, leggere e comprendere tutti i documenti allegati, stampati e online! Questo docu-

mento non descrive tutte le possibili congurazioni di sistema.

ES: ¡ADVERTENCIA! El funcionamiento incorrecto y el trabajo realizado de forma incorrecta pueden causar graves lesiones personales o

daños materiales. El Fronius Smart Meter sólo puede ser instalado y puesto en marcha por personal capacitado y sólo dentro del ámbito

de los reglamentos técnicos. Antes de trabajar con el dispositivo, lea y entienda todos los documentos adjuntos, impresos y en línea! Este

documento no describe todas las conguraciones posibles del sistema.

DA: ADVARSEL! Forkert betjening og forkert udført arbejde kan forårsage alvorlig personskade eller materielle skader. Fronius Smart

Meter må kun installeres og idriftsættes af uddannet personale og kun inden for rammerne af de tekniske forskrifter. Læs og forstå alle

vedlagte, trykte og online dokumenter, før du arbejder med enheden! Dette dokument beskriver ikke alle mulige systemkongurationer.

PB: ALERTA! Uma operação incorreta e trabalhos mal executados podem provocar graves danos às pessoas e aos equipamentos. A

instalação e o comissionamento do Smart Meter podem ser realizados somente por pessoal treinado e dentro das determinações técnicas.

Antes de trabalhar com o dispositivo, deve-se ler e compreender todos os documentos anexos, impressos e disponíveis online! Os módu-

los solares expostos à luz fornecem tensão ao inversor. Este documento não descreve todas as congurações de sistema possíveis.

Detailed, country-specic warranty terms are available on: www.fronius.com/solar/warranty

FIND MORE

INFORMATION

manuals.fronius.com/html/4204260349

SOFTWARE REQUIREMENTS

Fronius Datamanager 2.0 ≥ 3.16.1 version

Fronius Symo Hybrid ≥ 1.16.1 version

MEASURING INPUT

Nominal voltage (4-conductor) range 208 - 400 V (±20%)

Power consumption in the voltage path (max. voltage) ≤ 10 VA

Nominal frequency

Tolerance

50 - 60 Hz

45 - 65 Hz

Nominal current, lb5 A

Maximum current, Imax 65 A

Starting current 20 mA

Short-time overload

(EN IEC 62053-21, EN IEC 62053-23)

30 lmax / 0.001 s

Self-consumption - current path (max. current) ≤ 1 W

Power factor

Operating range

(EN IEC 62053-21, EN IEC 62053-23)

active cosφ 0.5 ind - 0.8 cap,

reactive sinφ 0.5 ind - 0.5 cap

Current distortion factor in acc. with EN 50470

OUTPUT

RS485 communication (Electrically isolated from measuring input)

Standard RS485 - 3 conductors

Protocol Compatible with Modbus RTU

Addresses 1 - 255

Baud rate 300, 2400, 9600 bit/s

Response time ≤ 200 ms

INSULATION (EN IEC 62052-11, EN IEC 62053-21)

Installation category III

Degree of pollution 2

Insulation voltage 4 kVAC RMS (1 min)

ELECTROMAGNETIC COMPATIBILITY

Emission test In acc. with EN IEC 62052-11, EN 50470-3

Immunity test In acc. with EN IEC 62052-11, EN 50470-3

OPERATING CONDITIONS

Reference temperature 25 °C (± 5 °C)

Operating range -25 to +55 °C

Temperature limit for storage and transport -30 to +80 °C

Mechanical environment

Electromechanical environment

HOUSING

Housing 3 modules according to DIN 43880

Sealable housing/terminal cover

Connection Screw connection

Mounting Can be snapped onto 35 mm DIN rail

Housing material Noryl, self-extinguishing

Degree of protection (EN 60529) IP51 housing, IP20 connections

Weight 240 grams

TERMINALS - MEASURING INPUT

Wire min. 1 mm² / max. 16 mm²

Recommended torque max. 2.8 Nm

TERMINALS - DATA OUTPUT (N-CONNECTOR)

Wire min 0.05 mm²

Recommended torque max. 0.4 Nm

Load / Source

MOUNT THE SMART METER (Step: 2)SWITCH OFF THE CIRCUIT BREAKER (Step: 1) 2 PHASES, 3 WIRES (Step: 3a) 3 PHASES, 4 WIRES (Step: 3b) 3 PHASES, 3 WIRES (Step: 3c) MOUNT THE PROTECTIVE COVERS (Step: 4)

1 3a

Load / Source

10 11

PASS

2633

PrG

Factory default: 2633

P14

AddrESS

001

PrG

Factory default: Modbus Address 001

0 0

2 sec. adjust / confirm

1 x page up / value up

1 x page down / value down

Setup your PV system in a few minutes.

START INSTALLATION

& password) in order to get the most out of the

PV System. Installing a new product does not

require a Login.

Imprint & Contac

erms & ConditionsData Privacy

Fronius Solar.start

1312

P18

END

START UP THE SMART METER (Step: 15)SETUP THE PASSWORD (Step: 12) SETUP THE ADDRESS (Step: 13)NAVIGATE IN THE SETTINGS (Step: 10) ENTER THE SETTINGS (Step: 11) EXIT THE SETTINGS (Step: 14)

0,4 Nm

CU Wire

0,05 mm²

Bypass (cable)

M-

85 CONNECT THE DATA CABLES (Step: 5) 6SET UP THE TERMINATING RESISTOR (Steps: 6-7) 7SWITCH ON THE CIRCUIT BREAKER (Step: 9)MOUNT THE CONNECTOR COVERS (Step: 8)

00 1

Manufacturer manualManufacturer manual

max. 300 m

GND

D+

M+ M-

D-

Invertere. g. Ohmpilot, Battery Smart Meter