Alula CAM-DB-JS1 Guide d'installation

Marque
Alula
Modèle
CAM-DB-JS1
Taper
Guide d'installation
CAM-DB-JS1
Video Doorbell
Installation Guide
Save this guide for future reference
What’s in the box
video doorbell mounting brackets
installation guide
mounting template
digital adapter &
sticker wire kit
Hardware overview
HD camera
microphone
light sensor
push button
speaker
reset button
terminals
mounting hardware
Black
Red
MicroSD card
Installing the MicroSD card
a. Remove screws and rubber cover from the back of the metal housing
b. Slide the metal housing down to separate the camera from back cover
c. Remove the rubber cover of the MicroSD slot on the left side of the camera
d. Insert the MicroSD card and put back the rubber cover
e. Slide the metal bracket back to its original position
bc
SD
de
a
Whether you have a standard or a digital doorbell, the setup process is the
same.
a. Turn off power to the doorbell
b. Remove the existing doorbell button and disconnect the two wires
c. Attach the wires to the terminals on the back of the Video Doorbell
d. Install the Digital Adapter to the door chime as shown below
e. Proceed to next step below
Note: It does not matter which wire
connects to which terminal of the
doorbell. It also does not matter which
Digital Adapter wires are connected
to the Front or Trans terminals. If you
have a digital door chime and your
doorbell button has an additional diode
connected to it, do not use it on the new
Video Doorbell.
Camera installation
a. Install the bracket where the previous doorbell was using the template,
2 small screws, and if necessary, the anchors.
b. Make sure the wires are fed through the appropriate square opening
in the bracket. Line up the video doorbell on the bracket and slide
down until secure.
c. When installed, turn power back on. Wait until the LED ring repeatedly
flashes 3 times (approx. 90 seconds for the unit to reboot)
Mounting the doorbell
Note: Do not mount the video doorbell until you have completed the in-app
connection and have the wiring completed. It is best to test the camera’s
functionality with the app prior to mounting.
Ensure the installation location is free from moisture and wires are not
exposed
angle bracket flat mount
Digital Adapter
Notes
Products with CE Marking comply with EMC Directive (2014/30/EU); Low Voltage Directive (2014/35/EU); RED (2014/53/EU);
ROHS Directive (2011/65/EU) issued by the Commission of the European Community. Compliance with these directives
implies conformity to the following European Norms:
EMC: EN 301 489
LVD: EN 62368-1
Radio: EN 300 328
If the camera system no longer functions or can no longer be repaired, it must be disposed of according to the valid statutory
regulations. Disposal of spent batteries/accumulators:
You are required by law (Battery Ordinance) to return all spent batteries and accumulators. Disposing of spent
batteries/accumulators with common household waste is prohibited! Batteries/accumulators that contain hazardous
substances are marked with the symbols on the side. These symbols indicate that it is prohibited to dispose of these
batteries/accumulators in the household waste. The abbreviations for the respective heavy metals are: Cd=cadmium,
Hg=mercury, Pb=lead. You can return spent batteries and accumulators that can no longer be charged to the designated
collection points in your community, outlets or wherever batteries or accumulators are sold. Following these instructions will
allow you to fulfill the legal requirements and contribute to the protection of our environment!
TRADEMARKS
Alula is a trademark owned by Alula Holdings, LLC. Wi-Fi is a trademark of The Wi-Fi Alliance.
Android is a trademark of Google LLC. IOS is a trademark of Cisco in the U.S. and other countries
and is used under license by Apple Inc.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received, including interference that may
cause undesired operation.
Caution: any changes or modifications to this device not explicitly approved by manufacturer could
void the user’s authority to operate this equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepti-
ble d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and
compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS
102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne
sur l'exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre
antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum
de 20 centimètres entre le radiateur et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Alula CAM-DB-JS1 Guide d'installation

Marque
Alula
Modèle
CAM-DB-JS1
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents