Maytag MHW4200BW Mode d'emploi
- Catégorie
- Machines à laver
- Taper
- Mode d'emploi
If you have any problems or questions, visit us at www.maytag.com
Pour tout problème ou question, consulter www.maytag.ca
Designed to use only HE
High Efficiency detergents.
Conçue pour l’utilisation
d’un détergent haute
efficacité seulement.
Use & Care Guide
Guide d’utilisation et d’entretien
Para obtener acceso
al Manual de uso y cuidado
en español, o para obtener
información adicional acerca
de su producto, visite:
www.maytag.com
FRONT-LOADING AUTOMATIC WASHER
LAVEUSE AUTOMATIQUE DE CHARGEMENT FRONTAL
W10441130B
W10441131B - SP
2
WASHER SAFETY
TABLE OF CONTENTS
WASHER SAFETY ..................................................................................2
ACCESSORIES ....................................................................................... 3
CONTROL PANEL AND FEATURES .................................................4
USING THE DISPENSER DRAWER ................................................. 6
CYCLE GUIDE..........................................................................................7
USING YOUR WASHER ....................................................................... 9
WASHER MAINTENANCE ................................................................ 13
TROUBLESHOOTING ........................................................................ 16
WARRANTY ........................................................................................... 23
ASSISTANCE OR SERVICE ............................................. Back Cover
TABLE DE MATIÈRES
SÉCURITÉ DE LA LAVEUSE ............................................................. 24
ACCESSOIRES .................................................................................... 25
TABLEAU DE COMMANDE ET CARACTÉRISTIQUES ............ 26
UTILISATION DU TIROIR DU DISTRIBUTEUR ........................... 29
GUIDE DE PROGRAMMES ............................................................. 29
UTILISATION DE LA LAVEUSE ........................................................ 32
ENTRETIEN DE LA LAVEUSE .......................................................... 36
DÉPANNAGE ......................................................................................... 39
GARANTIE .............................................................................................. 47
ASSISTANCE OU SERVICE .................................Couverture arrière
3
ACCESSORIES
Customize your new washer and dryer with the following
genuine Maytag accessories. For more information on options
and ordering, contact your dealer, call us at 1-800-901-2042,
or visit: www.maytag.com/accessories.
In Canada, call 1-800-807-6777, or visit: www.maytag.ca.
Stack Kit
If space is at a premium,
the stack kit allows the dryer
to be installed on top of
the washer.
Worksurface
The worksurface bridges the
washer and dryer, and provides
a convenient working and storage
area.
15" Pedestal
Color-matched pedestals raise the washer
and dryer to a more comfortable working
height. The large drawer provides convenient
storage.
4
CONTROL PANEL AND FEATURES
Not all features and cycles are available on all models.
POWER/CANCEL
Touch to turn the washer on and off. Touch to stop/cancel
a cycle at any time.
WASH CYCLE KNOB
Use your Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See “Cycle Guide” for detailed descriptions of cycles.
START
Touch and hold until the light above START comes on to start
a cycle, or touch once while a cycle is in process to pause it.
If you want to add a garment, you can touch START when the
“Add a Garment” LED is on.
LED DISPLAY AND SETTINGS
When you select a cycle, its default settings will light up and the
Estimated Cycle Time will be displayed. Factors such as load
size, wash temperature, and water pressure may affect the time
shown in the display during the cycle. Tightly packing garments,
unbalanced loads, or excessive suds may cause the washer to
adjust the cycle time, as well.
Touch the desired option along the right of the display to adjust
settings. See “Cycle Guide” for available settings on each cycle.
Not all settings are available with all cycles.
Temperature
The recommended wash temperature is preset for each cycle.
You may also select a wash temperature based on the type
of fabric and soils being washed. For best results, follow the
garment label instructions. All wash temperatures feature a
cold rinse.
Soil Level
The Soil Level setting (wash time) is preset for each wash cycle.
For most loads, use this preset soil level. When you change
the soil setting, the cycle time will increase or decrease in the
Estimated Cycle Time display.
For heavily soiled and sturdy fabrics, use the Soil Level
setting to select more wash time. For lightly soiled and
delicate fabrics, use the Soil Level setting to select less wash
time. Lower soil level settings will help reduce tangling and
wrinkling.
1
2
3
4
NOTE: The control panel features a sensitive surface that responds
to a light touch of your finger. To ensure your selections are registered,
touch the control panel with your finger tip, not your fingernail. When
selecting a setting or option, simply touch its name.
Model MHW4200
3
2
1
7
6
C
A
B
D
E
5
Spin Speed
This washer automatically selects the spin speed based on the
cycle selected. Some preset speeds can be changed.
n Higher
spin speeds mean shorter dry times, but may
increase wrinkling in your load.
n
Lower spin speeds reduce wrinkling, but will leave
your load more damp.
DELAY START
Use + and – to delay the start of the wash cycle by up to
12 hours. To turn off Delay Start, use + and – to set the delay
time to “0,” or touch POWER/CANCEL.
CYCLE STATUS LIGHTS
For details, see “Cycle Status Lights”.
OPTIONS
Touch to activate additional wash options or additional features on
the washer. Not all options are available on all models.
Steam for Stains
The Steam for Stains option adds additional soak and
wash time to many cycles to help remove tough stains, as well
as a steam boost for added cleaning power. An integrated
heater helps to maintain optimal wash temperatures. See
the “Cycle Guide” for cycles that allow the Steam for Stains
option.
Extra Rinse
Activate this option to add an extra rinse to most cycles.
NOTE: Some cycles include this feature as a default.
See “Cycle Guide” for details.
7
A
B
6
5
4
5
High Efficiency “HE” detergent compartment
This compartment holds liquid or powdered HE detergent for
your main wash cycle.
Liquid fabric softener compartment
Automatically dilutes and dispenses liquid fabric softener at
the optimum time in the cycle.
n
Use only liquid fabric softener in this dispenser.
Liquid chlorine bleach compartment
Automatically dilutes and dispenses liquid chlorine bleach at
the optimum time during the first rinse after the wash cycle.
This compartment cannot dilute powdered bleach.
A
B
C
B
A
HE detergent
Liquid fabric
softener
Chlorine bleach
8C
A
C
B
DISPENSER DRAWER
The dispenser drawer gives you the convenience of automatically
adding HE detergent, liquid chlorine bleach, and liquid fabric
softener to the wash load at the proper time. See “Using the
Dispenser Drawer” for information on using the dispenser drawer.
8
Fresh Spin™ Option
The Fresh Spin
™
option will periodically tumble the load after
the end of the cycle for up to 6 hours to reduce humidity.
To turn on the Fresh Spin
™
option, touch Fresh Spin.
If, however, the Fresh Spin
™
option is turned on, it will stay
on for all future cycles until turned back off – the washer
remembers the last on/off status set. To turn off the Fresh
Spin
™
option, touch Fresh Spin.
You may also activate the Fresh Spin
™
option without running
a cycle by touching and holding POWER/CANCEL for one
second, then touching and holding Fresh Spin for 3 seconds,
then touching and holding START for 3 seconds.
To turn off the Fresh Spin
™
option when it is running, touch
POWER/CANCEL.
NOTE:
The door will lock while the Fresh Spin
™
option is
active.
To cancel the option and unlock the door, touch
POWER/CANCEL.
Cycle Signal
Use this option to turn on or off the signal that sounds at end
of cycle.
To turn off the tones that sound when a setting is touched:
Touch and hold CYCLE SIGNAL for about 3 seconds.
Repeat to turn them on.
Control Lock
Touch and hold for 3 seconds to lock the controls to avoid
unwanted changes or operation. Touch and hold 3 seconds
again to unlock. You can still touch START to pause the cycle,
or touch POWER/CANCEL to turn the washer off.
B
C
D
E
Cycle Status Lights
Delay
If a Delay Start is set, the Delay indicator will light
and the delay time will count down in the display.
Door Locked
Door Locked will light to indicate that the door
is locked and cannot be opened without first
pausing or canceling the cycle.
Sensing
When START is touched and held, the washer
will first perform a self-test on the door lock
mechanism and the sensing light will come on.
You will hear a click, the drum will make a partial
turn, and the door will unlock briefly before locking again.
Once the door has locked the second time, the washer will drain
to calibrate the sensors; then it will begin tumbling and adding
water. The sensing process will continue throughout the cycle.
You may also hear water flowing through the dispenser, adding
detergent to the load.
After the load size is sensed, the estimated time based on load
size will be displayed. The actual cycle time may be lengthened;
however, the display will continue to show the estimated time.
The sensing light will blink once a second at various times during
the cycle, such as when the washer is reducing extra suds.
Add a Garment
When “Add a Garment” is lit, you may pause the washer,
open the door, and add items.
Steaming
This will light to show that the cycle is using a steam boost
for added cleaning power.
Done
Once the cycle is complete, this light will come on. Remove the
load promptly for best results. The Done indicator is also lit during
Fresh Spin™ option.
Choosing the Right Detergent
Use only High Efficiency detergents. The package will be marked
“HE” or “High Efficiency.” Low-water washing creates excessive
sudsing with a non-HE detergent. Using non-HE detergent will likely
result in longer cycle times and reduced rinsing performance. It may
also result in component failure and, over time, buildup of mold or
mildew. HE detergents are low-sudsing and quick-dispersing to
produce the right amount of suds for the best performance. They
hold soil in suspension so it is not re-deposited onto clean clothes.
Follow the manufacturer’s instructions to determine the amount of
detergent to use.
Use only High Efficiency (HE) detergent.
6
Adding HE detergent to dispenser
Powdered detergent:
Lift the selector to the high
position.
Liquid detergent:
Push down the selector to the
low position.
Pour a measured amount of HE
detergent into detergent compartment.
For powdered detergent, lift the selector
to the high position. For liquid detergent,
push down the selector to the low
position. Use only High Efficiency
(HE) detergent.
Do not overfill; adding too much detergent may cause
detergent to be dispensed into the washer too early.
IMPORTANT:
n Do not add single-dose laundry packet to dispenser drawer.
n Use powdered detergent when using the Delay Start option.
Liquid detergent may seep out before the wash begins.
HE detergent
compartment
1. Open the dispenser drawer.
2. Add laundry products as described in steps 4–6 in the
“Using Your Washer” section.
3. Slowly close the dispenser drawer. Make sure it is
completely closed.
NOTE: A small amount of water may remain in the dispensers from
the previous wash cycle. This is normal.
USING THE DISPENSER DRAWER
Selector
Selector
in high
position
Selector
in low
position
7
CYCLE GUIDE
* Steam for Stains option is only available when warm, hot, or extra hot water temperature is selected.
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings that best
fit the load being washed. Not all settings are available with each cycle, and some options cannot be used together.
NOTES:
n Not all cycles, temperatures, options, or spin speeds are available on all models.
n All wash temperature selections feature a cold rinse.
n Not all temperatures, spin speeds, or soil levels are labeled on the control panel.
continued on next page
Load Size Recommendations
For best results, follow the load size recommendations noted for each cycle.
Small load: Fill the washer drum with 3–4 items, not more than
1/4 full.
Medium load: Fill the washer drum up to about 1/2 full.
Large load: Fill the washer drum up to about 3/4 full.
Extra-large load: Fill the washer drum, but make sure clothes
can tumble freely. For best results, avoid packing tightly.
Cycle: Wash
Temperature: Spin
Speed: Soil
Level: Available
Options: Cycle Details:
Items to wash
using default
cycle settings:
Normally soiled cottons,
linens, sheets, and
mixed garment loads
Bright or darkly
colored cottons,
linens, casual and
mixed loads
Lightly soiled shirts,
blouses, trousers, pants
and dresses
Sheer fabrics, lingerie,
sweaters, and lightly-
soiled shirts, blouses,
trousers, pants, and
skirts
Normaly soiled sheets,
pillowcases, light
blankets, or throws
Small loads of
3–4 lightly soiled
garments
No clothes in washer
For small loads (3 –4 items) needed
quickly. This cycle combines high-
speed tumbling, a shortened wash
time, and an extra-high-speed spin
for reduced drying times.
Use this cycle every 30 washes to
keep the inside of your washer fresh
and clean. This cycle uses a higher
water level. Use with affresh® washer
cleaner tablet or liquid chlorine
bleach to thoroughly clean the inside
of your washer. This cycle should not
be interrupted. See “Washer Care.”
IMPORTANT: Do not place
garments or other items in the
washer during the Clean Washer
with affresh® cycle. Use this
cycle with an empty wash tub.
See “Washer Care” in “Washer
Maintenance.”
This cycle combines medium-speed
tumbling and an extra-high-speed
spin. This cycle is designed to
provide the most energy efficiency.
This cycle uses a concentrated
detergent solution along with cold
water throughout the cycle to gently
lift out stains and care for fabrics.
This cycle combines low-speed
tumbling and medium-speed spin
for gentle fabric care and reduced
wrinkling.
This cycle combines low-speed
tumbling and low-speed spin for
gentle fabric care and reduced
wrinkling.
The wash action of this cycle is
designed to keep large items from
tangling and balling up.
Normal
Wrinkle
Control
Delicates
Bedding
Rapid Wash
Clean
Washer
with
affresh®
Extra Heavy
Med
Light
Extra Heavy
Med
Light
Fresh Spin™
Extra Rinse
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Extra Heavy
Med
Light
Extra Heavy
Med
Light
Extra Heavy
Med
Light
Extra Heavy
Med
Light
Extra Hot
Hot
Warm
Cool
Cold
Extra Hot
Hot
Warm
Cool
Cold
Extra Hot
Hot
Warm
Cool
Cold
Cold Extra High
Med
Extra High
Med
Extra High
Med
Low
Extra High
Med
Low
Extra High
Med
Low
Extra High
Med
Low
Cold
Wash
Extra Hot
Hot
Warm
Cool
Cold
Extra Hot
Hot
Warm
Cool
Cold
8
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings that best
fit the load being washed. Not all settings are available with each cycle, and some options cannot be used together.
NOTES:
n Not all cycles, temperatures, options, or spin speeds are available on all models.
n All wash temperature selections feature a cold rinse.
n Not all temperatures, spin speeds, or soil levels are labeled on the control panel.
Cycle: Wash
Temperature: Spin
Speed: Soil
Level: Available
Options: Cycle Details:
Items to wash
using default
cycle settings:
* Steam for Stains option is only available when warm, hot, or extra hot water temperature is selected.
CYCLE GUIDE
†† Allergen
Allergen cycle reduces allergens by at least 95.1% based on independent third-party laboratory testing. It is recommended that you set your
hot water heater to 120°F (49°C) to ensure proper performance during this cycle.
† Sanitize
n This washer has a Sanitize Cycle that eliminates 99.9% of bacteria typically found on clothing, bedding, and towels, based on independent,
third-party laboratory testing. There is no carryover of bacteria between loads after the cycle is complete.
n Use the Sanitize Cycle to clean heavily soiled, colorfast fabrics. This combines an extra-hot water temperature to help ensure the removal
of heavy soils and stains. It is recommended that you set your hot water heater to 120°F (49°C) to ensure proper performance during this
cycle.
Wet load of clothes
Swimwear, items that
need rinsing
Clothing, bedding
and towels requiring
sanitization
Sturdy garments
and household items
exposed to possible
allergens
Heavily soiled fabrics Use this cycle for extremely soiled
garments and household items that
need additional cleaning power. This
cycle combines high-speed wash
action, extra-high-speed spin, and a
deep rinse to flush excess dirt from
the load.
Use Drain & Spin to remove excess
water from the load. Spin speed can
be set to a lower setting.
Select Drain & Spin; then select
Extra Rinse to add water. The
cycle includes an extra-high-speed
spin. For some fabrics, you may
wish to set the spin speed to a
lower setting.
Using the highest wash temperature
available ensures sanitization.
Check recommended wash
temperature of your items.
Uses more water to flush out
allergens such as dust mites
and pet dander from normally-
soiled items.
Drain
& Spin
Sanitize†
Allergen††
Power
Wash
N/A
N/A
Extra Heavy
Med
Light
Fresh Spin™
Delay Start
Fresh Spin™
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Steam for Stains*
Fresh Spin™
Extra Rinse
Delay Start
Extra Heavy
Med
Light
Extra Heavy
Med
Light
Extra Heavy
Med
Light
Extra Hot
Hot
Extra Hot
Hot
Warm
Cool
Cold
Extra Hot
Hot
Warm
Cool
Cold
Extra Hot
Extra High
Med
Low
Extra High
Med
Low
Extra High
Med
Low
Extra High
Med
Low
Extra High
Med
Drain
& Spin
with
Extra Rinse
9
USING YOUR WASHER
Sort items by recommended cycle, water temperature, and
colorfastness. Separate heavily soiled items from lightly soiled.
Separate delicate items from sturdy fabrics. Treat stains promptly
and check for colorfastness by testing stain remover products on
an inside seam.
1. Sort and prepare your laundry
Place a load of sorted clothes loosely in the washer. Items need to
move freely for best cleaning and to reduce wrinkling and tangling.
Close the washer door by pushing it firmly until the latch clicks.
n Depending on load type and cycle, the washer can be fully
loaded, but not tightly packed. Washer door should close easily.
See “Cycle Guide” for loading suggestions.
n Mix large and small items and avoid washing single items. Load
evenly.
n Wash small items in mesh garment bags. For multiple items, use
more than one bag and fill bags equally.
3. Load laundry into washer
First wash cycle without laundry
Before washing clothes for the first time, if not completed during
the final installation step, choose the NORMAL cycle and run it
without clothes. Use only HE detergent. Use 1/2 the manufacturer’s
recommended amount for a medium-size load. This initial cycle
serves to ensure the interior is clean before washing clothes.
IMPORTANT:
n Empty pockets. Loose change, buttons, or any small object can
plug pumps and may require a service call.
n Close zippers, fasten hooks, tie strings and sashes, and remove
non-washable trim and ornaments.
n Mend rips and tears to avoid further damage to items during
washing.
n Turn knits inside out to prevent pilling. Separate lint-takers from
lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint
from towels, rugs, and chenille fabrics.
n Do not dry garments if stains remain after washing, because heat
can set stains into fabric.
n Always read and follow fabric care labels and laundry
product instructions. Improper usage may cause damage
to your garments.
2. Add laundry products (if desired)
Single-dose laundry packet, Oxi-type boosters, color-safe bleach,
or fabric softener crystals can be added to the drum prior to
adding laundry.
NOTE: Do not add clothes to washer drum prior to adding
laundry products. Always follow manufacturer’s instructions.
10
Add liquid chlorine bleach to the bleach compartment. Do not overfill,
dilute, or use more than 2/3 cup (165 mL). Do not use color-safe
bleach or Oxi in the same cycle with liquid chlorine bleach.
n Always measure liquid chlorine bleach. Use a measuring cup with
a pour spout; do not guess.
n Do not fill beyond the “MAX” level. Overfilling could cause
garment damage.
6. Add liquid chlorine bleach to dispenser
(if desired)
Pour a measured amount of liquid fabric softener into liquid fabric
softener compartment. Always follow manufacturer’s directions for
correct amount of fabric softener based on your load size.
Fabric softener is always dispensed in the last rinse, even if Extra
Rinse is selected.
IMPORTANT: Do not overfill, dilute, or use more than 1/4 cup
(60 mL) of fabric softener. Do not fill past the MAX line. Overfilling
dispenser will cause fabric softener to immediately dispense into
washer.
n Do not spill or drip any fabric softener onto the clothes.
n Do not use liquid fabric softener dispenser balls in this washer.
They will not dispense correctly.
5. Add liquid fabric softener to dispenser
(if desired)
4. Add HE detergent
Powdered
HE detergent
Adjust the selector, based on type of HE detergent used
(either liquid or powdered). See “Using the Dispenser Drawer”
instructions on how to use the dispenser.
Liquid
HE detergent
7. Touch POWER/CANCEL to turn on
washer (optional)
Slowly close the dispenser drawer. Make sure the drawer is closed
completely, then touch POWER/CANCEL to turn on the washer or
go to Step 8.
USING LAUNDRY PRODUCT DISPENSERS
NOTE: Do not add single-dose laundry packets, Oxi-type boosters,
color-safe bleach, or fabric softener crystals to dispensers. They will
not dispense correctly.
USING YOUR WASHER
11
8. Select CYCLE*
The display will show the default settings for the selected cycle. To
adjust a setting, touch its name – Temperature, Soil Level, or Spin
Speed. Adjusting settings will change the Estimated Cycle Time.
Tightly packing the load, unbalanced loads, or excessive suds may
also cause the washer to increase the cycle time.
Turn cycle knob to select your wash cycle. See “Cycle Guide” for
details on cycle features.
9. Adjust settings, if desired*
10. Select any additional options*
To add an option to the cycle, touch its name – Steam for Stains,
Extra Rinse, Fresh Spin, or Cycle Signal. To remove an option from
the selected cycle, touch the option again.
* Not all options and settings are available with all cycles.
See “Cycle Guide” for available options and settings.
11. Setting a delayed start
If you do not want to begin a cycle immediately, you may choose
the DELAY START option. This will delay the start of the wash
cycle by up to 12 hours.
To set a delayed start:
1. Touch DELAY START + and – to set the desired delay time.
2. Touch and hold START to set the delay. The delay countdown
has started when the START light stops blinking.
12
12. Touch and hold START to begin
wash cycle
Touch and hold START to start the wash cycle. To pause
a cycle in progress, touch START once, then touch and
hold again to continue the cycle. To cancel a cycle, touch
POWER/CANCEL.
Once you touch and hold START, you will hear the door lock,
unlock, and lock again. The washer door will remain locked
during the wash cycle.
Unlocking the door to add garments:
If you need to open the door to add 1 or 2
missed garments, you may do so while the
“Add a Garment” light is lit.
Touch START once; the door will unlock
once the washer movement has stopped.
This may take several minutes. Then close
door and touch and hold START again to
restart the cycle.
13. Remove garments promptly
after cycle is finished
Promptly remove garments after cycle has
completed to avoid odor and rusting of metal
objects on garments. When unloading garments,
pull back the door seal and check for small items
between the tub and the washer drum.
If you will be unable to remove the load promptly,
use the Fresh Spin™ option
.
If selected, the Fresh
Spin™ option will tumble the load periodically for
up to 6 hours. To turn off the Fresh Spin™ option,
touch POWER/CANCEL. To set the washer so that the Fresh Spin™
option does not come on for future cycles, touch Fresh Spin.
NOTE:
n
The door will remain locked while the Fresh Spin™ option is
active. To cancel the option and unlock the door, touch POWER/
CANCEL.
n
A small amount of water may remain in the dispensers after the
wash cycle is complete. This is normal.
n This washer has a tight seal to avoid water leaks. To avoid odors,
leave the door open to allow the washer to dry between uses.
OR
USING YOUR WASHER
13
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efficiency (HE) detergents and follow the
HE detergent manufacturer’s instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the rate
at which detergent and soil residue accumulate inside your
washer, which in turn may result in undesirable odor.
2. Use warm or hot water washes sometimes (not exclusively
cold water washes), because they do a better job of controlling
the rate at which soils and detergent accumulate.
3. Always leave the washer door slightly ajar between uses
to help dry out the washer and prevent the buildup of
odor-causing residue.
Cleaning Your Front Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This Washer
Maintenance Procedure should be performed, at a minimum,
once per month or every 30 wash cycles, whichever occurs
sooner, to control the rate at which soils and detergent may
otherwise accumulate in your washer.
Cleaning the Door Seal
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect the colored seal between the door opening and the
drum for stained areas or soil buildup. Pull back the seal
to inspect all areas under the seal and to check for foreign
objects.
3. If stained areas or soil buildup are found, wipe down these
areas of the seal using either of the following two procedures:
a. affresh® Grit Grabber™ Cloth Procedure:
i. When the cycle is complete, gently pull back the rubber
door seal and clean the entire surface with the rough
side of the Grit Grabber™ cloth.
b. Dilute Liquid Chlorine Bleach Procedure:
i. Mix a dilute bleach solution, using 3/4 cup (177 mL) of
liquid chlorine bleach and 1 gallon (3.8 L) of warm tap
water.
ii. Wipe the seal area with the dilute solution, using
a damp cloth.
iii. Let stand 5 minutes.
iv. Wipe down area thoroughly with a dry cloth and let
washer interior air dry with door open.
IMPORTANT:
n Wear rubber gloves when cleaning with bleach.
n Refer to the bleach manufacturer’s instructions for
proper use.
WASHER CARE (cont.)
Cleaning the Inside of the Washer
This washer has a special cycle that uses higher water volumes
in combination with affresh® Washer Cleaner or liquid chlorine
bleach to thoroughly clean the inside of the washer. Steam
washer models also utilize steam to enhance cleaning in this
special cycle.
NOTE: Read these instructions completely before beginning the
cleaning process.
Begin procedure
1. affresh® Washer Cleaner Cycle Procedure
(Recommended for Best Performance):
a. Open the washer door and remove any clothing or items.
b. Add an affresh® Washer Cleaner tablet to the washer
drum.
c. Do not add the affresh® Washer Cleaner tablet to the
dispenser drawer.
d. Do not add any detergent or other chemical to the washer
when following this procedure.
e. Close the washer door.
f. Select the CLEAN WASHER cycle.
g. Touch and hold START to begin the cycle. The Clean
Washer Cycle Operation is described below.
2. Chlorine Bleach Procedure:
a. Open the washer door and remove any clothing or items.
b. Open the dispenser drawer and add liquid chlorine bleach
to the MAX level in both the bleach compartment and the
fabric softener compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage over time.
c. Close the washer door and the dispenser drawer.
d. Do not add any detergent or other chemicals to the
washer when following this procedure.
e. Close the washer door.
f. Select the CLEAN WASHER cycle.
g. Touch and hold START to begin the cycle. The Clean
Washer Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle.
Description of Clean Washer Cycle Operation:
1. The Clean Washer cycle will determine whether clothing
or other items are in the washer.
2. If no items are detected in the washer, it will proceed with
the cycle.
a. If any items are detected in the washer, “rL” (remove load)
will be displayed. The door will unlock. Open washer and
remove any garments from the washer drum.
b. Touch POWER/CANCEL to clear the “rL” code.
c. Touch and hold START to restart the cycle.
After the cycle is complete, leave the door open slightly to allow
for better ventilation and drying of the washer interior.
WASHER MAINTENANCE
Replace inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
WATER INLET HOSES
14
WASHER CARE (cont.)
Cancellation of Clean Washer Cycle Operation:
If the Clean Washer cycle is canceled by the user after it has
been initiated, it may take up to 30 minutes for the washer
to purge any affresh® Cleaner, chlorine bleach, or other
chemistry from the wash system and to adequately rinse any
remaining chemistry. The washer door will remain locked until
the cancellation process has been completed. This ensures no
cleaning chemistry will be carried over to the next wash cycle
and reduces the potential for damage to subsequent loads of
laundry or to the washer itself.
Clean Washer Cycle Cancellation Procedure:
1. Touch POWER/CANCEL on the washer once.
2. The washer will begin to drain and rinse away the remaining
cleaning chemistry.
3. The cycle will complete the cancellation process in
approximately 30 minutes or less.
4. The washer then can be used to either repeat the Clean
Washer cycle or to wash laundry using one of the regular
wash cycles selected by the user.
Cleaning the Dispensers
After a period of using your washer, you may find some residue
buildup in the washer’s dispensers. To remove residue from the
dispensers, remove the drawer and wipe the surfaces with a
damp cloth and towel dry either before or after you run the Clean
Washer cycle. Use an all-purpose surface cleaner, if needed.
IMPORTANT: Dispenser is not dishwasher safe.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to help keep it
looking new. Use mild soap and water.
IMPORTANT: To avoid damaging the washer’s finish, do not use
abrasive products.
WASHER CARE (cont.)
Removing the Dispenser
To remove:
1. Pull dispenser drawer out until it stops.
2. Press down on the release tab and pull straight out to
remove the dispenser.
3. Lift off cover panel by
pulling straight up.
To replace:
1. Slide cover panel back
onto posts on dispenser.
2. Align edges of dispenser
with guides in washer,
then slide dispenser
back into slot.
WASHER MAINTENANCE
15
Operate your washer only when you are home. If moving, or
not using your washer for a period of time, follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer to avoid flooding due
to water pressure surges.
3. Clean dispensers. See “Cleaning the Dispensers.”
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets, disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum
and run washer on NORMAL cycle for about 2 minutes to
mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
NON-USE AND VACATION CARE
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain hose from drain system and from back
of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer drum.
6. Bundle power cord with a rubber band or cable tie to keep
it from hanging onto the ground.
IMPORTANT: Call for service to install new transport bolts.
Do not reuse transport bolts. Washer must be transported
in the upright position. To avoid structural damage to your
washer, it must be properly set up for relocation by a certified
technician.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through NORMAL cycle to clean washer and
remove antifreeze, if used. Use only HE detergent. Use half
the manufacturer’s recommended amount for a medium-size
load.
16
If you experience Possible Causes Solution
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Error Code Appears in Display
“Sud” (Excess suds)
appears in display
Excessive suds in washer. Washer is
running a suds reduction routine.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer’s instructions.
Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer. If code appears again,
call for service.
F
08 followed by
E
01
(water supply error)
appears in display
Check for proper water supply. Both hoses must be attached and have water flowing to the inlet
valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
F
09 followed by
E
01
(drain pump system
error) appears in display
Check plumbing for correct drain
hose installation. Drain hose extends into
standpipe farther than 41⁄2" (114 mm).
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor.
F
05 followed by
E
02
(door will not lock)
appears in display
Washer door not locking. Touch POWER/CANCEL to cancel the cycle. Make sure the door
is closed completely and latching. Check for items in the washer
drum that may be keeping the door from closing completely.
Washer beeps when
START is touched Door not closed. Close the door completely.
F
07 followed by
E
01
(motor drive error)
appears in display
Motor is having difficulty turning
the drum. Washer is tightly packed. Remove some items. See “Cycle Guide”
for load size recommendations. Make sure that all shipping
materials have been removed. See the Installation Instructions.
“rL” (remove load)
appears in display
Load detected in drum during Clean
Washer with affresh® cycle. Remove items from washer drum and restart Clean Washer with
affresh® cycle.
Washer making error
beeps
Door has not been opened and closed
for at least 3 cycles. This code may appear when the washer is first turned on.
Open and close the door to clear the display.
Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle.
F
##
E
## code other
than as described above
appears in display
System error code. Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer. If code appears again,
call for service.
Not using HE detergent or using too
much HE detergent.
Use only HE detergent. Always measure detergent and follow
manufacturer’s directions based on load size and soil level.
TROUBLESHOOTING
“Int” (interrupted)
appears in display The cycle was paused or cancelled. The washer can take 20 to 30 minutes to stop spinning and drain
and will display this error code during that time. Touch POWER/
CANCEL once to clear the code. Then touch POWER/CANCEL
again to restart washer.
17
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience Possible Causes Solution
Feet may not be in contact with the
floor and locked. Front and rear feet must be in firm contact with floor, and washer
must be level to operate properly. Jam nuts must be tight against
the bottom of the cabinet.
Check floor for flexing or sagging. If flooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See “Level the Washer” in Installation Instructions.
Load could be unbalanced or too large. Avoid tightly packing the load. Avoid washing single items. Balance
a single item such as a rug or jeans jacket with a few extra items.
Item or load not suitable for selected cycle. See “Cycle Guide” and
“Using Your Washer.”
Empty pockets before washing. Loose items such as coins could
fall between washer drum and tub or may block pump. It may be
necessary to call for service to remove items.
Fill hoses not attached tightly. Tighten fill-hose connection.
Properly seat all four fill-hose flat washers.
Drain hose connection. Check that the drain hose is properly secured to drainpipe or
laundry tub.
Check household plumbing for leaks or
clogged sink or drain. Water can back up out of a clogged sink or drainpipe. Check
all household plumbing for leaks (laundry tubs, drain pipe, water
pipes, and faucets.)
Fill hose washers.
Noises
It is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel drum.
Objects caught in washer drain system.
Clicking or metallic noises
Gurgling or humming The pump may make a humming sound with periodic gurgling or
surging as final amounts of water are removed during the spin/drain
cycles. This is normal at certain stages of the cycle.
Washer may be draining water.
Water Leaks
Check the following for
proper installation
Vibration, rocking, or
“walking”
Load not completely
covered in water Water level not visible on door or
does not cover clothes. This is normal for an HE front load washer. The washer senses load
sizes and adds the correct amount of water for optimal cleaning.
Washer not performing as expected
Washer may not be level.
The door will lock, unlock, and lock again. You will hear 3 clicks after
touching and holding START. This is normal.
Door locking or unlocking.
Not using HE detergent or using too
much HE detergent. Only use HE detergent. Suds from regular detergents can
cause leaking from the door or rear of cabinet. Always measure
detergent and follow manufacturer’s directions based on your load
requirements.
Water or suds leaking from
door or rear of cabinet
Residue on door glass. Periodically clean the underside of the glass window to avoid
potential leaks.
The shipping bolts are still in the back
of the washer. See “Remove transport bolts from washer” in the Installation
Instructions.
Door opened during “Add a Garment.” Water can drip off the inside of the door when the door is opened
after the start of a cycle.
Rolling or sloshing
and occasional clicking
(on low-speed spin)
This is normal at certain stages of the cycle.Steel balls in the balancing system are
balancing the load.
Vibration or Off-Balance
18
Normal washer operation. Door must be completely closed and latched for washer to run.
Washer will pause during certain phases of cycle. Do not interrupt
cycle.
The washer pauses for about 2 minutes during certain cycles.
Allow the cycle to continue. Some cycles feature periods of
tumbling and soak.
Washer may be stopped to reduce suds.
Cold Wash uses less water in the beginning of the cycle to
provide a high concentration of detergent for optimal cleaning
action. Following this concentrated tumbling, more water is used
to complete the wash.
Plug power cord into a grounded 3-prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Check electrical source or call an electrician to check if voltage
is low.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Washer not loaded as recommended. Remove several items, rearrange load evenly in washer drum.
Close door and touch and hold START.
Do not add more than 1 or 2 additional items after cycle has started
to avoid tightly packing or unbalancing.
Do not add more water to the washer.
If you experience Possible Causes Solution
Washer won’t run or fill,
washer stops working Check for proper water supply. Both hoses must be attached and have water flowing to
inlet valve.
Both hot and cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water flow.
Check proper electrical supply.
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Washer not performing as expected (cont.)
The washer door is not firmly shut. The door must be closed during operation.
TROUBLESHOOTING
19
Washer not performing as expected (cont.)
If you experience Possible causes Solution
Incorrect or wrong wash
or rinse temperatures Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and have
both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Select DRAIN & SPIN to remove any water remaining in the
washer. The washer door will unlock at the end of the drain.
Water remaining in washer after cycle.Door locked at end of
wash cycle
Using cycles with a lower spin speed. Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/speed spin
for your garment.
Washer not loaded as recommended. A tightly packed or unbalanced load may not allow the washer to
spin correctly, leaving the load wetter than normal. See “Cycle
Guide” for load size recommendation for each cycle.
Washer not draining/
spinning, loads are
still wet
Drain hose extends into standpipe
farther than 4.5" (114 mm).
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening.
Not using HE detergent or using too
much HE detergent. Use only HE detergent. Suds from regular detergent or using
too much detergent can slow or stop draining or spinning. Always
measure and follow manufacturer’s directions for your load. To
remove extra suds, select DRAIN & SPIN with Extra Rinse. Do not
add detergent.
The load may be out of balance. Avoid washing single items. Balance a single item such as a rug or
jeans jacket with a few extra items.
The drain hose is clogged, or the
end of the drain hose more than
96" (2.4 m) above the floor.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See “Installation
Requirements” in Installation Instructions.
The drain hose fits too tightly
in the standpipe, or it is taped
to the standpipe.
The drain hose should be loose yet fit securely. Do not seal the
drain hose with tape. The hose needs an air gap. See “Secure the
Drain Hose” in Installation Instructions.
Small items may have been caught in
the pump or stuck between the washer
drum and the outer tub.
Check the drum for any items sticking through the drum holes.
Empty pockets and use garment bags when washing small items.
If the “Add a Garment” light is lit, touch START once. The door will
unlock.
Door locks when cycle has started.
Door will not unlock
Washing many loads. Your hot water tank may not have enough hot water to keep up
with the number of hot or warm washes. This is normal.
Not using HE detergent or using too
much HE detergent.
Only use HE detergent. Suds from regular detergents can
slow or stop the washer. Always measure detergent, following
manufacturer’s directions based on your load requirements.
To remove suds, cancel cycle. Select DRAIN & SPIN with Extra
Rinse. Touch and hold START. Do not add more detergent.
After 3 wash cycles in a row are completed, the door must be
opened and then closed before a new cycle can begin.
Door not opened between cycles.
Washer won’t run or fill,
washer stops working
(cont.)
While this option is on, the load is tumbled periodically for up to
6 hours. The door remains locked during this time. To unlock the
door, cancel the option by touching POWER/CANCEL.
Fresh Spin™ option is on.
TROUBLESHOOTING
20
Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the inlet
valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Not using HE detergent or using too
much HE detergent. The suds from regular detergent can cause the washer
to operate incorrectly.
Use only HE detergent. Always measure detergent and follow
manufacturer’s directions based on load size and soil level.
Washer not loaded as recommended. Avoid tightly packing the washer. The washer will not rinse well
if tightly packed. Load with dry items only. See the “Cycle Guide”
for load size recommendations for each cycle.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer has started.
If you experience Possible Causes Solution
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Washer not performing as expected (cont.)
Washer not loaded as recommended.Not cleaning or
removing stains Add load loosely. Items need to move freely for best cleaning. See
the “Cycle Guide” for load size recommendations for each cycle.
Add only 1 or 2 garments after washer has started.
Not using HE detergent or using too
much HE detergent. Use only HE detergent. Always measure detergent and follow
manufacturer’s directions based on load size and soil level.
Hard water or high level of iron (rust)
in water. You may need to install a water softener and/or iron filter.
Fabric softener dispensing ball used. Dispensing balls will not operate correctly with this washer.
Add liquid fabric softener to the fabric softener compartment.
Powdered detergent used for
low-speed cycle.
Consider using liquid detergent.
Load is wrinkled,
twisted, or tangled
Washer not loaded as recommended. Add load loosely. Items need to move freely reduce wrinkling and
tangling. See the “Cycle Guide” for load size recommendations
for each cycle.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
Select a lower spin speed. Note that items will be wetter than
when using a higher speed spin.
Wash action and/or spin speed too
high for load.
Unload the washer as soon as it stops or use Fresh Spin™ option
if you will not be able to unload the washer at the end of the
cycle.
The washer is not unloaded promptly.
Use the Delicates cycle or another cycle with a low spin speed
to reduce wrinkling.
Not choosing the right cycle for the load
being washed.
If safe for load, use warm or hot wash water.
The wash water was not warm enough
to relax wrinkles.
The load may be out of balance. When load unbalance occurs, a washing process will start to
redistribute the load. This may lengthen the cycle time. Avoid
washing single items. Balance a single item such as a rug or jeans
jacket with a few extra items.
For best performance, not all settings
are available with each cycle, and some
options cannot be used together.
Desired setting or
option does not light See the “Cycle Guide” for the available settings and options for
each cycle.
TROUBLESHOOTING
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Maytag MHW4200BW Mode d'emploi
- Catégorie
- Machines à laver
- Taper
- Mode d'emploi
dans d''autres langues
- English: Maytag MHW4200BW User guide