Crow DECT ULE FLD B Guide d'installation

Marque: Crow

Modèle: DECT ULE FLD B

Taper: Guide d'installation

DECT ULE-

FLD BUG

WATER LEAKAGE DETECTOR

CR-DU-FLD EURO

CR-DU-FLD USA

ELECTRONIC ENGINEERING LTD.

INSTALLATION INSTRUCTIONS

P/N 7101103 REV. A (O.Z.)

Issue Date: Nov. 30

, 2015

INTRODUCTION

This DECT ULE FLD BUG detector is an

advanced, fully supervised low-current wireless

detector that includes a DECT ULE transceiver for

reliable system operation.

A dedicated Adhesive tape is supplied with this

device.

This DECT ULE FLD BUG uses smart message

control, which verifies that all messages are

successfully transmitted, so that no event will be

uninformed to the system.

This DECT ULE FLD BUG detector includes series

of messages for full communication administration

(Keep Alive, Tamper Status, Battery Status, Alert,

Configuration, etc.) as well as test transmission

signals.

FEATURES

 DECT ULE RF protocol.

 Low current Technology.

 Powered by 2 AA 1.5V Alkaline batteries.

 Battery life: up to 4 years with Alkaline batteries.

 Frequency Band: All DECT Standard Bands.

 Water leak Detection transmission.

 Tamper Open/Close transmission.

 Keep Alive transmission.

 Battery status transmission.

 Bi-Color LED indications for monitoring &

Pairing.

 Range up to 500m on open space.

 Alarm triggered by the sensor.

 Remotely configurable.

 Friendly Pairing and Installation processes.

OPERATION

The DECT ULE FLD BUG detector transmits the

following events data:

KEEP ALIVE – A periodical transmission

indicating detector’s presence. The time interval is

configurable – the minimum value is 3 seconds.

ALARM – Alarm transmission triggered by the

Flood indicating on water leakage detection. The

Red LED will blink once.

LOW BAT – Whenever the battery reaches a pre-

set low level (~2.5V) Battery Low signal will be

sent. When the Battery level drops below Cut Off

level (~2.3V) the device will stop functioning and

the Red LED will blink for 10 seconds.

TAMPER – Whenever the DECT ULE FLD BUG

is removed from its bracket, a message will be

transmitted with “Tamper” signal.

PACKAGE CONTENTS

1. Flood Sensor,

2. Surface Mount,

3. Installation Guide (this document).

PREPARE FOR INSTALLATION

1. Pull the device from the surface mount by

holding it by the Pull-Out sockets (Fig. 3) and

pulling it out.

2. Pull out the plastic strip pops out from the

device’s battery compartment and wait until the

Red LED stops blinking.

3. Insert the device into its surface mount.

Match the device insertion guide on the sensor

(Fig 2) with the insertion guide on the surface

mount (Fig 3).

4. Continue with the pairing process.

FIGURE 1 – DETECTOR’S FRONT (TOP)

SIDE

FIGURE 2 – DETECTOR’S BACK (TOP)

SIDE

FIGURE 3 – SURFACE MOUNT FRONT

SIDE

FIGURE 4 – SURFACE MOUNT BACK

SIDE

PAIRING PROCESS

1. Pull the device from the surface mount by holding

it by the Pull-Out sockets (Fig. 3) and pulling it

out.

2. Initiate the Base Station pairing process.

3. Initiate the device pairing process by pressing the

pairing button (Fig. 2) for 5 seconds. The Green

LED will constantly turn On. When the Green

LED starts blinking release the pairing button.

4. The device should register to the Base Station.

5. When registration process is successfully

completed the Green LED will constantly light On

for 3 seconds and then turn Off.

** If the registration process failed the Red LED

will blink (remove the battery and run the pairing

process again – repeat this process starting from

step 3).

6. Insert the device into its surface mount.

Match the device insertion guide on the sensor

(Fig 2) with the insertion guide on the surface

mount (Fig 3).

BATTERY REPLACEMENT

1. Pull the device from its surface mount by

holding it by the Pull-Out sockets (Fig. 3) and

pulling it out.

2. Open the battery compartment by pressing it

outwards via the Battery Compartment Opening

Slot (Fig. 2).

3. Note the polarity of the batteries. Replace the

batteries with new batteries.

4. Close the battery compartment.

5. Insert the device into its surface mount.

Match the device insertion guide on the sensor

(Fig 2) with the insertion guide on the surface

mount (Fig 3).

SELECT MOUNTING LOCATION

As the detector is a wireless transceiver, and in

order to take full advantage of its sophisticated

operation, do not install the detector in areas where

large metal objects could interfere with the

transmission of signals.

This Water Leak sensor is designed in a way that

there is no special mounting required. The sensor

has to be put on the floor or surface, in close

proximity to potential water leakage points and in a

way that when there is a leak, water will not drop

directly on the sensor.

LED

Pull-Out

Sockets

Water Sensing

Probes Opening

Sensor Insertion

Guide

Water Sensing

Probes

Adhesive Tape

Tamper

Switch

Sensor

Insertion

Guide

Battery

Compartment

Opening Slot

Battery

Strip

Pairing

Button

Water Sensing

Probes

MOUNTING THE DETECTOR

In order to avoid unintended misplacements of the

device throughout the years, it is recommended to

use the double sided adhesive tape that is attached

to the device surface mount's back side in order to

fix the device to the floor / surface.

In order to do so:

1. Make sure that the device’s mounting location

is clean and dry.

2. Pull the device from its surface mount by

holding it by the Pull-Out sockets (Fig. 3) and

pulling it out.

3. Peel off the upper cover of the adhesive tape

placed on the back side of the surface mount.

4. Mount the surface mount at the selected

location by firmly pressing it towards the floor /

mounted surface with the adhesive tape facing

the floor / mounted surface.

5. Insert the device into its surface mount.

6. Match the device insertion guide on the sensor

(Fig 2) with the insertion guide on the surface

mount (Fig 3).

TRANSMISSION TESTS

TAMPER transmission test –

Changing the tamper switch state (by pulling /

inserting the device to / from its surface mount) will

cause Tamper transmissions. Verify receiving the

indications on your Application / Base Station.

IDENTIFICATION transmission test –

Use your Application / Base Station and send

Identification Request to the device. The device will

start blinking the Green & Red LEDs alternately – 5

times each LED starting with the Green LED.

EMPTY

FCC & IC STATEMENT

FCC ID: NFC-CRDU

IC: 8164A- CRDU

This device complies with FCC Rules Part 15 and with

Industry Canada license-exempt RSS standard(s).

Operation is subject to two conditions: (1) This device may

not cause harmful interference, and (2) this device must

accept any interference that may be received or that may

cause undesired operation.

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment. End users

must follow the specific operating instructions for satisfying

RF exposure compliance. This transmitter must not be co-

located or operating in conjunction with any other antenna

or transmitter.

Canada: Under Industry Canada regulations, this radio

transmitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the transmitter

by Industry Canada. To reduce potential radio interference

to other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful

communication. This device complies with Industry Canada

licence-exempt RSS standard(s).

FCC & IC STATEMENT (Continue)

Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device

must accept any interference, including interference that

may cause undesired operation of the device.

Conformément à la réglementation d'Industrie Canada, le

présent émetteur radio peut fonctionner avec une antenne

d'un type et d'un gain maximal (ou inférieur) approuvé pour

l'émetteur par Industrie Canada. Dans le but de réduire les

risques de brouillage radioélectrique à l'intention des autres

utilisateurs, il faut choisir le type d'antenne et son gain de

sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à

l'établissement d'une communication satisfaisante. Le

présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

FCC & IC STATEMENT (Continue)

Note: The digital circuit of this device has been tested

and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and

receiver.

-Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV

technician for help.

REGULATORY APPROVALS

This DECT ULE detector conforms to the essential

requirements set out by:

 RTTE directive:1999/5/EC

 EMC directive: 2004/108/EC

 Low Voltage directive: 2006/95/EC

 RoHS directive: 2011/65/EU

Harmonized Standards applicable to this products are:

 EN301406

 EN301489-6

 EN301489-1

 EN61000-6-3

 EN60950-1

 EN50581

 UL 2017

 C22.2 No.205-12

TECHNICAL SPECIFICATIONS

RF Protocol DECT ULE

Modulation Type GFSK

Signaling Type Non – Emergency signaling

Type (NM)

Frequency 1880–1900 MHz - Europe

1920–1930 MHz - USA/Canada

Event Transmission Flood Alert, Tamper, Keep Alive,

Battery status.

Detection Method Internal sensor.

Range in open space >500m

Battery Alkaline 1.5V Type: AA

Battery life expectancy >4 years (10 activation per day)

Current Consumptions: Standby 4A

Average 19µA

Maximum (TX) 250mA

Low Battery 2.5VDC

Cut Off Battery 2.3VDC

Transmit Power (Typ.): 23dBm (EURO), 20dBm (USA)

Tamper Switch Tamper

Operating temperature -10C to +55C

Dimensions 68mm x 68mm x 20mm

Weight 45 gr. (inc. batteries 92 gr.)

CAUTION !!!

RISK OF EXPLOSION IF BATTERY IS REPLACED

BY DIFFERENT TYPE / MODEL. DISPOSE USED

BATTERIES ACCORDING TO ITS INSTRUCTIONS

ATTENTION !!!

RISQUE D'EXPLOSION SI LA PILE EST

REMPLACÉE PAR UN TYPE INCORRECT.

WARNING!!!

Changes or modifications to this equipment not

expressly approved by the party responsible for

compliance (Crow Electronic Engineering Ltd.) could

void the user’s authority to operate the equipment.

CROW ELECTRONIC ENGINEERING LTD. ("Crow") - WARRANTY POLICY CERTIFICATE

This Warranty Certificate is given in favor of the purchaser (hereunder the "Purchaser") purchasing the products directly from Crow or from its

authorized distributor.

Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the

last day of the week and year whose numbers are printed on the printed circuit board inside these products (hereunder the "Warranty Period").

Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's

procedures, as such procedures are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective

in materials or workmanship under normal use and service. Repaired products shall be warranted for the remainder of the original Warranty Period.

All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall

be borne solely by the Purchaser.

Crow's warranty under this Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the

products (or any part thereof) by anyone other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product

which Crow did not provide; (d) failure caused by software or hardware which Crow did not provide; (e) use or storage other than in accordance with

Crow’s specified operating and storage instructions.

There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend

beyond the description on the face hereof.

This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the

Purchaser in connection with the products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate

replaces all other warranties and liabilities, whether oral, written, (non-mandatory) statutory, contractual, in tort or otherwise.

In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by

negligence of the Crow or any third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of

liability whatsoever. Crow does not represent that these products can not be compromised or circumvented; that these products will prevent any

person injury or property loss or damage by burglary, robbery, fire or otherwise; or that these products will in all cases provide adequate warning or

protection.

Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events

occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property

loss or damage as a result.

Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to

give any warning.

If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s

maximum liability shall not in any case exceed the purchase price of these products, which shall be the complete and exclusive remedy against

Crow.

CROW ELECTRONIC

ENGINEERING LTD.

12 Kineret St.

Airport City, 70100 Israel

Tel. +972 3 9726000

Fax. +972 3 9726001