Procom PCK110VT Manuel utilisateur

IMPORTANT: Read and understand this manual before

assembling, starting or servicing heater. Improper use

of heater can cause serious injury. Keep this manual for

future reference.

Never use heater in living or sleeping areas.

Heater is suitable for outdoor use and for use on com-

bustible oors.

PORTABLE FORCED AIR HEATERS

KEROSENE/DIESEL HEATER WITH BUILT-IN THERMOSTAT

OWNER’S MANUAL

PCK110VT - ADJUSTABLE 80-110,000 BTU/HR

PCK160VT - ADJUSTABLE 110-160,000 BTU/HR

PCK175VT - ADJUSTABLE 125-175,000 BTU/HR

PCK220VT - ADJUSTABLE 160-220,000 BTU/HR

Questions, problems, missing parts? Before returning to your retailer, call

our customer service department at 1-866-573-0674, 7:30 am - 4:15 pm CST,

Monday through Friday or email customerservice@usaprocom.com

www.usaprocom.com

160108-01C2

2. Fueling

a) Personnel involved with fueling shall be

qualied and thoroughly familiar with

the manufacturer's instructions and

applicable regulations regarding the

safe fueling of heating units.

b) Only the type of fuel specied on the

heater's data plate shall be used.

c) All ame shall be extinguished and the

heater allowed to cool, prior to fueling.

d) During fueling, all fuel lines and fuel-

line connections shall be inspected for

leaks. Any leaks shall be repaired prior

to returning the heater to service.

e) At no time shall more than one day's

supply of heater fuel be stored inside

a building in the vicinity of the heater.

Bulk fuel storage shall be outside the

structure.

f) All fuel storage shall be located a mini-

mum of 25 feet (762 cm) from heaters,

torches, welding equipment and similar

sources of ignition (exception: fuel res-

ervoir integral with heater unit or any

authorized auxiliary tank connected to

heater unit).

g) Whenever possible, fuel storage shall

be conned to areas where oor pen-

etrations do not permit fuel to drip onto

or be ignited by a re at lower elevation.

h) Fuel storage shall be in accordance

with the authority having jurisdiction.

3. Use only the electrical voltage and fre-

quency specied on model plate.

4. Heater is suitable for outdoor use.

5. Heater must be grounded. Use only a

properly grounded three-wire extension

cord. Plug into grounded outlet only.

6. Use only in areas free of ammable va-

pors or high dust content.

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble,

operate or service this heater.

Improper use of this heater can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning resemble the u,

with headaches, dizziness and/or nausea. If

you have these signs, the heater may not be

working properly. Get fresh air at once! Have

heater serviced. Some people are more af-

fected by carbon monoxide than others. These

include pregnant women, persons with heart

or lung disease or anemia, those under the

inuence of alcohol and those at high altitudes.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

1. Use only kerosene, #1/#2 diesel/fuel oil,

JET A or JP-8 fuels to avoid risk of re or

explosion. Never use gasoline, oil from

crank cases, naphtha, paint thinners,

alcohol or other highly ammable fuels.

SAFETY

TABLE OF CONTENTS

Safety ........................................................ 2

Unpacking.................................................. 3

Assembly ................................................... 3

Product Identication and Label Locations 5

Specications ............................................ 6

Fuels .......................................................... 6

Ventilation .................................................. 6

Operation ................................................... 7

Operation with Portable Generator ............ 8

Storing, Transporting or Shipping .............. 8

Preventative Maintenance Schedule ......... 8

Troubleshooting ......................................... 9

Service Procedures ................................. 13

Wiring Diagram ........................................ 18

Technical Service..................................... 18

Accessories ............................................. 18

Parts ........................................................ 19

Replacement Parts .................................. 23

Warranty .................................................. 24

www.usaprocom.com

3160108-01C

SAFETY

UNPACKING

7. Minimum clearance from any combustible

materials: 8 feet (244 cm) from hot air

outlet, 6 feet (183 cm) from top, and 4

feet (120 cm) from sides and inlet.

8. Locate heater on a stable and level sur-

face while hot or operating or a re may

occur.

9. Heater is acceptable for use on ooring

such as wood (a combustible material).

10. Use only in well vented areas. Before

using heater, provide at least a 3 ft

2

(2800 cm

2

) opening of fresh, outside air

for each 100,000 Btu/Hr (30 kw) of rating.

11. Keep children and animals away from

heater at all times.

12. Never start heater when combustion

chamber is hot or if fuel has accumulated

in combustion chamber.

13. This heater is equipped with a thermostat.

Heater may start at anytime.

14. Never leave a heater plugged in without

adult supervision if children or animals are

likely to be present.

15. Use caution when moving or storing

heater when fuel tank contains fuel. Fuel

spillage can occur.

16. Use heater only in accordance with lo-

cal ordinances and codes. Canadian

residents should refer to CSA standard

B139, Installation Code for Oil Burning

Equipment for recommended installation

practice.

17. Never use gasoline, crankcase drainings,

naphtha, paint thinners, alcohol or other

highly ammable fuels.

18. Never use heater where gasoline, paint

thinner or other highly ammable vapors

are present.

19. Never use heater in living or sleeping

areas.

20. Never move, handle, refuel or service a

hot, operating or plugged-in heater.

21. Never attach duct work to front or rear of

heater.

22. Heaters used in the vicinity of tarpaulins,

canvas or similar enclosure materials shall

be located a safe distance from such ma-

terials. The recommended minimum safe

distance is 10 feet (304.8 cm). It is further

recommended that these enclosure ma-

terials be of a re retardant nature. These

enclosure materials shall be securely fas-

tened to prevent them from igniting or from

upsetting the heater due to wind action.

23. Unplug heater when not in use.

24. Never block air inlet (rear) or air outlet

(front) of heater.

25. Warning to New York City Residents

For Use Only At Construction Sites in

accordance with applicable NYC codes.

26. Never use external fuel sources or tanks

that are not specically designed for use

with this heater.

Figure 1 - Wire Guard Moved to Locked

Position

1. Remove all packing items applied to

heater for shipment.

2. Remove all items from carton.

3. Check items for any shipping damage. If

heater is damaged call ProCom Heating,

Inc. at 1-866-573-0674 for replacement

parts before returning to dealer.

ASSEMBLY

WIRE GUARD

All Models

Grasp wire guard from top of shell and pull

towards front of heater until it locks into place

in slots on both sides of upper shell.

www.usaprocom.com

160108-01C4

WHEEL ASSEMBLY

Models 160, 175 and 220

1. Slide Axle (A) through holes in wheel support frame.

2. Slide Wheel Spacer (B), then wheel (D) (concave side facing outward) onto axle.

3. Attach Acorn Nut (C) nger tight to end of axle.

4. Repeat steps 2 and 3 for opposite side, then tighten nuts with adjustable wrench.

Axle (A)

Acorn Nut (C)

Wheel (D)

Spacer (B)

Figure 2 - Wheel Assembly, 160, 175 and 220 Models

HANDLE ASSEMBLY

Models 160, 175 and 220

1. Slide rear handle (E) onto Wheel Support Frame. Insert Screws (G) from rear and attach

lock nuts (F).

2. Place Front Handle (I) under ange of fuel tank and insert 4 screws (J) from top of ange

through holes in ange into holes in handle. Attach Lock Nuts (H) and tighten.

Rear Handle (E)

Screw, 10-24 x 1.5 (G)

Lock Nut 10-24 (F)

Screw 1/4-20 x 1.75" (J)

Front Handle (I)

Figure 3 - Handle Assembly, 160, 175 and 220 Models

ASSEMBLY

www.usaprocom.com

5160108-01C

PRODUCT IDENTIFICATION AND LABEL LOCATIONS

Fueling Label

Part No. 160168-01

Control Label

Part No. 160167-02

CSA Label (Rating Plate)

Part No. 160111-04, 110 model

Part No. 160112-02, 160 model

Part No. 160112-03, 175 model

Part No. 160112-05, 220 model

Operating Label

Part No. 160173-01

Operating Codes Label

Part No. 160174-01

Maintenance Label

Part No. 160175-01

Caution Label

Part No. 160172-01

Figure 4 - Product Identication & Label Locations

English Warnings

Label 160110-01

French Warnings

Label 160110-02

Spanish Warnings

Label 160110-03

NY, MA and CA

Information Label

Part No. 160169-01

All Models

Right Side

(220 Model Shown)

All Models

Left Side

(110 Model Shown)

Front

Handle

(160, 175 &

220 models)

Hot Air

Outlet

Control

Panel

Rear Handle

(160, 175 &

220 models)

Wire

Guard

Top Handle

(110 model)

Fuel

Tank

Cold Air

Inlet

Power

Cord

Fuel Cap

Fuel

Gauge

Hot Air

Outlet

www.usaprocom.com

160108-01C6

SPECIFICATIONS

VENTILATION

Example: A 220,000 Btu/Hr (64.5 kw) heater

requires one of the following:

• a two-car garage door [16 feet (4.88 meter)

opening] raised 5" (12.7 cm)

• a single-car garage door [9 feet (2.74 me-

ter) opening] raised 9" (22.9 cm)

• two, 30" (76.2 cm) windows raised 16"

(40.6 cm)

FUELS

• noticeable odor

• additional fuel lter maintenance

* Use of #2 diesel/fuel oil in extreme cold

temperatures may require nontoxic anti-icer

additives.

Do not use fuels heavier than No. 2 grade

or heavy oils such as oil drained from crank-

cases. These heavy oils will not ignite properly

and will contaminate the heater.

IMPORTANT: Use a KEROSENE ONLY (blue)

or DIESEL ONLY (yellow) storage container.

Be sure storage container is clean. Foreign

matter such as rust, dirt or water will cause the

ignition control assembly to shut down heater.

Foreign matter may also require heater's fuel

system to be frequently cleaned.

PCK110VT PCK160VT PCK175VT PCK220VT

Output Rating 80K-110K 110K-160K 125K-175K 160K-220K

Fuel (all models) Use only kerosene, #1/#2 diesel*/fuel oil, JET A or JP-8 fuels

Fuel Tank Capacity 5.5 gal/20.8 L 10 gal/37.9 L 10 gal/37.9 L 14 gal/53 L

Fuel Consumption (per hr) 0.82 gal/3.1 L 1.19 gal/4.5 L 1.3 gal/4.9 L 1.64 gal/6.2 L

Pump Pressure 6.9 PSI (hot) 6.7 PSI (hot) 6.8 PSI (hot) 8.4 PSI (hot)

Electric Requirements 120 V/60 HZ 120 V/60 HZ 120 V/60 HZ 120 V/60 HZ

Amperage (Normal Run) 2.9 3.2 3.4 4.6

Typical Motor Speed 3400 RPM 3400 RPM 3400 RPM 3400 RPM

Motor 1/4 hp 1/4 hp 1/4 hp 1/4 hp

Shipping Weight 42 lbs/19 kg 71 lbs/32.2 kg 71 lbs/32.2 kg 77 lbs/35 kg

Heater Weight without

Fuel (approx)

36 lbs/16.3 kg

60.5 lbs/27.4 kg 60.5 lbs/27.4 kg 66 lbs/29.9 kg

WARNING: Use only kero-

sene, #1/#2 diesel/fuel oil, JET

A or JP-8 fuels to avoid risk

of re or explosion. Never use

gasoline, oil drained from crank-

cases, naphtha, paint thinners,

alcohol or other highly am-

mable fuels.

Use only kerosene, #1/#2 diesel*/fuel oil,

JET A, JP-8 fuels. Heavier fuels such as No.

2 fuel oil, No. 2 diesel fuel may also be used

but will result in:

WARNING: Provide a fresh air

opening of at least three square

feet (2,800 square cm) for each

100,000 BTU/HR rating. Provide

extra fresh air if more heaters

are being used. The minimum

ventilation requirements must

be followed to avoid risks as-

sociated with carbon monoxide

poisoning. Make certain these

requirements are met prior to

operating heater.

www.usaprocom.com

7160108-01C

ASSEMBLED IN THE USA BY:

ASSEMBLE AUX ETATS-UNIS PAR:

ENSAMBLADA EN LOS EE.UU.POR:

PROCOM HEATING, INC.

2800 GRIFFIN DRIVE

BOWLING GREEN, KY 42101

`

THERMOSTAT MODE

MODE/RESET

PUMP PRESSURE

STAND BY

ON/STOP

TEMPERATURE

MANUAL MODE

MODE MANUEL/MODO MANUAL

MODE/REINITIALISATION

`

MARCHE/ARRET

^

MODE THERMOSTAT

THERMOSTATO MODO

MODO/RESTABLECER

ENCENDER/APAGAR

TEMPERATURA

160167-02

PRESSION DE LA POMPE

PRESION DE BOMBA

`

ADJUST

AJUSTE

IMPORTANT: Review and under-

stand the warnings in the Safety

section, page 2. They are needed

to safely operate this heater.

Follow all local ordinances and

codes when using this heater.

TO START HEATER

1. Follow all ventilation and safety information.

2. Locate heater to provide maximum circu-

lation of the heated air. Follow all location

requirements noted in Safety, pages

2 and 3.

3. Fill fuel tank with fuel and attach fuel cap.

Use only kerosene, #1/#2 diesel/fuel oil,

JET A or JP-8 fuels to avoid risk of re or

explosion. Never use gasoline, oil drained

from crankcases, naphtha, paint thinners,

alcohol or other ammable fuels.

4. Plug heater’s power cord into approved,

grounded, three-wire extension cord.

Extension cord must be at least 6 feet

(1.8 m) long.

Extension Cord Size Requirement

• 6 to 10 feet (1.8 to 3 m) long, use 18

AWG (0.75 mm

2

) rated cord

• 11 to 100 feet (3.3 to 30.5 m) long, use

16 AWG (1.0 mm

2

) rated cord

• 101 to 200 feet (30.8 to 61 m) long, use

14 AWG (1.5 mm

2

) rated cord

5. Plug extension cord into standard 120

volt/60 hertz, 3-prong grounded outlet.

6. Push ON/STOP button to ON. An alarm will

sound and the display will start countdown

to ignition. The heater will start and pump

pressure will be displayed for 6 seconds.

7. Push MODE/RESET button to select

desired operating mode.

Note: When operating in Thermostat

Mode, press the MODE/RESET button

once to change to Manual Mode. When

operating in Manual Mode, Press the

MODE/RESET button twice within 5 sec-

onds to change to Thermostat Mode.

Manual Mode LED On: Adjust output to

desired setting. Press to raise the BTU

output. Press to lower the BTU output.

Note: After startup, heater BTU output can

be immediately adjusted, but adjustments

will not take effect for 2 minutes. This al-

lows the heater to stabilize.

Thermostat Mode LED On: Adjust ther-

mostat by pressing to change set point

higher. Press to change set point lower.

If thermostat set temperature is higher

than the surrounding air temperature by

3° F, the heater will ignite. If the thermostat

set temperature is lower than surrounding

air temperature, the heater will not ignite.

Heater output will adjust automatically to

maintain set temperature.

WARNING: This heater is

equipped with a thermostat.

Heater may start at any time.

TO STOP HEATER

1. Push ON/STOP button to stop heater.

2. Unplug heater when not in use.

TO RESET HEATER

1. Wait two minutes before restarting.

2. Push MODE/RESET button to restart

heater.

OPERATION

LED display will show surrounding temperature

unless up and down arrow keys are pressed.

After pressing these keys, display shows set

point temperature for ve seconds and then will

change back to display surrounding temperature.

Exposure to direct sunlight or extreme cold may

affect temperature reading and/or thermostat

operation.

This thermostat will store the last set point

even if power is removed. Unit will maintain

this set point until a new set point is entered.

Figure 5 - Controls Display

FAULT CODES

This heater will display fault codes whenever

there is a control shutdown. See Trouble-

shooting, pages 9 - 12, before attempting to

rectify any problems with your heater.

www.usaprocom.com

160108-01C8

Ground Wire (#10 AWG -

Stranded-Copper)

Copper

or Brass

Grounding

Point

Figure 6 - Typical Generator Grounding

Method (Generator construction may

vary from that shown)

PREVENTATIVE MAINTENANCE SCHEDULE

WARNING: Never service heater while it is plugged in, operating

or hot. Severe burns and electrical shock can occur.

OPERATION WITH PORTABLE GENERATOR

Alternator

Ground Lug

WARNING: Before operating

heater or any appliance from a

portable generator, verify that

generator has been properly con-

nected to earth ground. Improper

grounding or failure to ground

generator can result in electro-

cution if a ground fault occurs.

Refer to owner’s manual supplied

by generator manufacturer for

proper grounding procedures.

Operating voltage range of heater is 95 to 135

Volts. Prior to plugging heater into generator

output voltage should be veried (if generator

is equipped with automatic idle feature, output

voltage should be measured with generator

running at full speed). If voltage does not

STORING, TRANSPORTING OR SHIPPING

3. Properly dispose of old and dirty fuel.

Check with local automotive service sta-

tions that recycle oil.

4. If storing, store heater in dry place. Make

sure storage place is free of dust and

corrosive fumes.

IMPORTANT: Do not store kerosene over

summer months for use during next heating

season. Using old fuel could damage heater.

measure in this range heater should not be

plugged into generator.

Refer to Operation, page 7, for starting, stop-

ping and resetting heater procedures.

Note: If shipping, transport companies require

fuel tanks to be empty.

1. Remove excess fuel from tank using a si-

phon pump. Drain remaining fuel through

ller neck by tipping heater to the rear.

2. If any debris is noted in old fuel, add 1 or 2

quarts of clean kerosene to tank, stir and

drain again. This will prevent excess debris

from clogging lters during future use.

Item How Often How To

Fuel tank Clean every season or as needed. See Storing, Transporting, or

Shipping, above.

Air output and

lint lters

Replace every 500 hours of operation or

once a year.

See Air Output, Air Intake and

Lint Filters, page 13.

Air intake lter Wash and dry with soap and water every 500

hours of operation or as needed.

See Air Output, Air Intake and

Lint Filters, page 13.

Fuel lter Clean twice a heating season or as needed. See Fuel Filter, page 14.

Fan blades Clean every season or as needed. See Fan, page 13.

Motor Not required/permanently lubricated.

www.usaprocom.com

9160108-01C

TROUBLESHOOTING

WARNING: Never service heater while it is plugged in, operating

or hot. Severe burns and electrical shock can occur.

WARNING: High voltage! Unplug heater before servicing.

DISPLAY POSSIBLE CAUSE REMEDY

Display shows

C3,C4,C5,C6, C7,C8

or C9.

1. Control remembers codes

from prior operation. Control

only remembers codes C3,

C4, C5 and C6.

Codes C7, C8 and C9 are

reset when placing the unit

in standby and backing into

operational mode.

1. Press MODE/RESET button

to clear Code and restart

heater.

Display is off. 1. No power to heater (All LED’s

are off).

2. Bad electrical connection

between control and power

cord.

1. Check power cord connec-

tions.

2. Unplug heater. Check all

electrical connections (see

Wiring Diagram, page 18).

Display shows room tem-

perature.

1. Thermostat setting is too low. 1. Adjust thermostat to a higher

setting by pressing but-

ton or change to MANU-

AL MODE by pressing the

MODE/RESET button.

Display shows C8 Te m -

perature over 100°F.

1. Room or ambient tempera-

ture exceeds 100°F.

1. Operate heater in a cooler

environment.

Display shows C9 Low

Pressure.

1. Bad electrical connection

between motor and power

cord.

2. Motor locked-fan obstructed.

3. Motor locked-pump ob-

structed.

4. Motor defective.

1. Unplug heater. Check all

electrical connections (see

Wiring Diagram, page 18).

2. Unplug heater. Clear fan

obstruction.

3. Service pump (see page 17).

4.

Unplug heater. Replace

motor.

FAULT CONDITION

Motor does not start after heater is plugged in and ON/STOP button is ON.

www.usaprocom.com

160108-01C10

TROUBLESHOOTING

WARNING: High voltage! Unplug heater before servicing.

FAULT CONDITION

Motor starts and runs but heater does not ignite.

DISPLAY POSSIBLE CAUSE REMEDY

Display shows C9 Low

Pressure.

1. Air line or tting leaking.

2. Pump cover leaking.

Pump cover screws loose.

3. Pump cover gasket leaking.

Pump output lter clogged.

4. Pump pressure is low.

5. Pump pressure is low. Can-

not adjust to specication.

1. Unplug heater. Check air

lines and ttings for leaks.

Correct all leaks.

2. Unplug heater. Check pump

cover for leaks. Tighten pump

cover screws to 10-20 in-lbs.

3. Unplug heater. Replace pump

output lter. See Pump Pres-

sure Adjustment page 14.

4. Adjust pump pressure to

specication. See Pump Pres-

sure Adjustment, page 14.

5. Service pump, see page 17.

Display shows C3 No

Ignition.

1. No fuel in fuel tank.

2. Water in fuel tank.

3. Pump pressure incorrect.

4. Dirty Fuel Filter.

5. Obstruction in Nozzle.

6. Bad electrical connection

between ignitor and control.

7. Blown control fuse.

8. Defective ignitor.

9. Defective ignition control as-

sembly.

1. Fill Tank. See Fuels, page 6.

Restart heater.

2. Drain and flush fuel tank

with kerosene. See Storing,

Transporting or Shipping,

page 8.

3. See Pump Pressure Adjust-

ment, page 14.

4. See Fuel Filter, page 14.

5. See Nozzle Assembly, page

16.

6. Check electrical connections.

See Wiring Diagram, page 18.

7. Replace control fuse, see

page 17.

8. Replace ignitor and control

fuse, see pages 14 & 17.

9. Replace ignition control as-

sembly.

www.usaprocom.com

11160108-01C

TROUBLESHOOTING

WARNING: High voltage! Unplug heater before servicing.

FAULT CONDITION

Heater ignites but control assembly shuts heater off before running out

of fuel.

DISPLAY POSSIBLE CAUSE REMEDY

Display shows C4 Flame

Extinguished.

1. Not enough fuel in tank to

maintain combustion.

2. Water in fuel tank.

3. Pump pressure incorrect.

4. Dirty fuel lter.

5. Obstruction in nozzle.

6. Photocell assembly not prop-

erly installed.

7. Dirty photocell lens.

8. Defective photocell.

1. Fill tank. See Fuels, page 6.

Restart heater

2. Drain and flush fuel tank

with kerosene. See Storing,

Transporting or Shipping,

page 8.

3. See Pump Pressure Adjust-

ment, page 14.

4. See Fuel Filter, page 14.

5. See Nozzle Assembly, page

16.

6. Make sure photocell boot is

fully seated in bracket.

7. Clean photocell lens.

8. Replace photocell.

Display shows C5 Im-

proper Flame.

1. Pump pressure too high.

2. Heater inlet or outlet is cov-

ered and unit is not getting

enough air for combustion.

3. Fan set screw is loose.

1. See Pump Pressure Adjust-

ment, page 14.

2. Unplug heater. Remove ob-

structions or loose material

from heater inlet or outlet.

3. Tighten fan set screw to

40-50 in-lbs. See service

procedures on page 13.

Display shows C6 Flame

Change.

1. Heater inlet suddenly blocked

by debris.

2. Water in fuel tank

3. Dirty fuel lter

4. Obstruction in nozzle

5. Fan set screw is loose

1. Unplug heater. Remove ob-

structions or loose material

from heater inlet.

2. Drain and flush fuel tank

with kerosene. See Storing,

Transporting or Shipping,

page 8.

3. See Fuel Filter, page 14.

4. See Nozzle Assembly, page

16.

5. Tighten fan set screw to

40-50 in-lbs. See Service

Procedures on page 13.

www.usaprocom.com

160108-01C12

TROUBLESHOOTING

DISPLAY POSSIBLE CAUSE REMEDY

Display shows C7 Control

button stuck.

1. One or more of the control

buttons is depressed continu-

ously (stuck).

2. Defective control assembly.

1. Unplug heater. Depress and

release each control button

several times to check opera-

tion. Every button should click

every time it is depressed.

2. Replace control assembly.

Display shows C8 Te m -

perature Over 100°F.

1. Room or ambient tempera-

ture exceeds 100°F.

1. Operate heater in a cooler

environment.

Display shows C9 Low

Pressure (Setting 5).

1. Air line or tting leaking.

2. Pump cover leaking. Pump

cover screws loose.

3. Pump cover gasket leaking.

Pump output lter clogged.

4. Pump pressure is low.

5. Pump pressure is low. Can-

not adjust to specification.

Pump lters are dirty.

6. Pump pressure is low, pump

has excessive wear or im-

proper adjustment.

1. Unplug heater. Check air

lines and fittings of leaks.

Correct all leaks.

2. Unplug heater. Check pump

cover for leaks. Tighten pump

cover screws to 10-20 in-lbs.

3. Unplug heater Replace pump

output lter. See Pump Rotor,

page 17.

4. Adjust pump pressure to

specication. See Pump Pres-

sure Adjustment, page 14.

5. Replace pump filters. See

page 13.

6. Adjust pump rotor gap or re-

place pump rotor and blades.

See page 17.

WARNING: High voltage! Unplug heater before servicing.

FAULT CONDITION

(Continued) Heater ignites but control assembly shuts heater off before

running out of fuel.

www.usaprocom.com

13160108-01C

Figure 7 - Upper Shell Removal

Motor

Shaft

Setscrew

Figure 8 - Fan, Motor Shaft, and

Setscrew Location

Motor

Shaft

Back of Flat on

Motor Shaft

1.82"

Motor

Shaft

Length

Fan

Setscrew

Touching

Back of Flat

on Motor

Shaft

Figure 9 - Fan Cross Section

Fan

Motor

SERVICE PROCEDURES

WARNING: To avoid risk of

burn and electrical shock, never

attempt to service heater while it

is plugged in, operating, or hot.

UPPER SHELL REMOVAL

1. Remove screws along each side of heater

using 5/16" nut-driver. These screws at-

tach upper and lower shells together. See

Figure 7.

2. Lift upper shell off.

3. Remove fan guard.

FAN

IMPORTANT: Remove fan from motor shaft

before removing motor from heater. The

weight of the motor resting on the fan could

damage the fan pitch (see Figure 8).

1. Remove upper shell (see Figure 7).

2. The fan is located with the set screw in

contact with the back of at on motor as

shown in Figure 9.

3. Use 1/8" Allen wrench to loosen setscrew

which holds fan to motor shaft (see Fig-

ure 8).

4. Slip fan off motor shaft.

5. Clean fan using a soft cloth moistened

with kerosene or solvent.

6. Dry fan thoroughly.

7. Place setscrew on flat of shaft.

Tighten setscrew firmly (40-50 inch-

pounds/4.5-5.6 n-m).

8. Replace fan guard and upper shell.

AIR OUTPUT, AIR INTAKE AND

LINT FILTERS

1.

Remove upper shell (see Figure 7).

2. Remove lter end cover screws using

5/16" nut-driver (see Figure 10).

3. Remove lter end cover.

4. Replace air output and lint lters.

5. Wash or replace air intake lter.

6. Replace lter end cover.

7. Replace fan guard and upper shell.

IMPORTANT: Do not oil lters.

Air Intake

Filter

Lint Filter

Filter

End

Cover

Air Output

Filter

Figure 10 - Air Output, Air Intake, and

Lint Filters

www.usaprocom.com

160108-01C14

ASSEMBLED IN THE USA BY:

ASSEMBLE AUX ETATS-UNIS PAR:

ENSAMBLADA EN LOS EE.UU.POR:

PROCOM HEATING, INC.

2800 GRIFFIN DRIVE

BOWLING GREEN, KY 42101

`

THERMOSTAT MODE

MODE/RESET

PUMP PRESSURE

STAND BY

ON/STOP

TEMPERATURE

MANUAL MODE

MODE MANUEL/MODO MANUAL

MODE/REINITIALISATION

`

MARCHE/ARRET

^

MODE THERMOSTAT

THERMOSTATO MODO

MODO/RESTABLECER

ENCENDER/APAGAR

TEMPERATURA

160167-02

PRESSION DE LA POMPE

PRESION DE BOMBA

`

ADJUST

AJUSTE

SERVICE PROCEDURES

PUMP PRESSURE

ADJUSTMENT (USING

EXTERNAL GAUGE)

1. Remove pressure gauge plug from lter

end cover (see Figure 11).

2. Install 0-15 PSI pressure gauge.

3. Start heater (see Operation, page 7). Al-

low heater to reach operating temperature

(approx. 10 minutes).

4. Set heater to MANUAL MODE, SETTING

5. This is the only setting that will allow

pressure adjustment.

5. Adjust pressure. Turn relief valve to right

to increase pressure. Turn relief valve to

left to decrease pressure. See specica-

tions with Figure 12 for correct pressure

for each model. DO NOT OVERTIGHTEN

ADJUSTMENT SCREW. Service pump if

pressure can not be adjusted to proper

setting (see Figure 12).

6. Remove pressure gauge. Replace pres-

sure gauge plug in lter end cover.

Figure 11 - Pressure Gauge Plug

Removal

Pressure

Gauge

Plug

Relief Valve

LED Display

Pressure

Gauge

Figure 12 - Adjusting Pump Pressure

Using External Gauge

Figure 13 - Adjusting Pump Pressure

Using Built-In Gauge

Relief

Valve

Pump

Model Pressure

110 6.9 PSI

160 6.7 PSI

175 6.8 PSI

220 8.4 PSI

Fuel Filter,

Bushing,

and Lower

Fuel Line

Upper Fuel Line

Side

Cover

Figure 14 - Fuel Filter Removal

FUEL FILTER

1. Remove side cover screws using 5/16"

nut-driver.

2. Remove side cover with a 5/16" nut driver.

On 160, 175 and 220 models, remove two

wheel support bolts and nuts with a Phillips

screwdriver and an adjustable wrench.

the heater to MANUAL MODE, SETTING

5, then press the MODE/RESET button

once. Pump pressure will be displayed

(example: "6.9") for 5 seconds.

4. Adjust pressure. Turn relief valve to right

to increase pressure. Turn relief valve to

left to decrease pressure. See specica-

tions with Figure 12 for correct pressure

for each model. DO NOT OVERTIGHTEN

ADJUSTMENT SCREW. Service pump if

pressure can not be adjusted to proper

setting (see Figure 12).

PUMP PRESSURE ADJUSTMENT

(USING BUILT-IN GAUGE)

1. This heater continuously monitors pump

pressure with a built-in pressure sensor.

2. When the heater starts, pump pressure

will be displayed for 6 seconds.

3. To display the pump pressure while oper-

ating, operate the heater for 2 minutes, set

www.usaprocom.com

15160108-01C

7. Remove ignitor screw with a 1/4" nut

driver. Carefully remove ignitor from

nozzle adapter bracket.

CAUTION: Do not bend or

strike ignitor element. Handle

with care.

8. Carefully remove replacement ignitor from

packing.

9. Carefully guide ignitor into opening in

nozzle adapter bracket. Do not strike

ignitor element. Attach ignitor to nozzle

adapter bracket with screw using a 1/4"

nut driver. Torque 0.90 to 1.69 N-m (8 to

15 in-lbs) Do not over torque.

10. Replace combustion chamber.

11. Route the ignitor wires back down through

the hole in the lower shell. Connect wires

to the ignition control assembly (see Fig-

ure 15).

12. Replace fuse on ignition control assembly

with the fuse provided with the SP002-01

Igniter Kit. See Ignition Control Assembly,

page 17.

13. Replace control side cover.

14. Connect and route fuel line hose and air

line hose to nozzle adapter assembly.

15. Replace photocell in photocell bracket.

16. Replace fan (see page 13).

17. Replace fan guard and upper shell (see

page 13).

SERVICE PROCEDURES

Photocell

Bracket

Ignitor

Ignitor Screw/

Washer Assembly

Nozzle

Adapter

Bracket

Ignitor

Element

Combustion

Chamber

Nozzle Adapter

Bracket Opening

Figure 16 - Ignitor SP002-01

Replacement

Figure 15 - Disconnecting Ignitor Wires

from Ignition Control Assembly

Photocell

Bracket

Air Line

Hose

Fuel Line

Hose

Combustion

Chamber

Photocell

Assembly

Ignitor

Nozzle Adapter

Bracket

Ignition

Control

Assembly

Side

Cover

Ignitor

Wire

3. Pull upper fuel line off fuel lter neck (see

Figure 14, page 14).

4. Carefully pry bushing, fuel lter, and lower

fuel line out of fuel tank (see Figure 14,

page 14).

5. Wash fuel lter with clean fuel and replace

in tank.

6. Attach upper fuel line to fuel lter neck.

7. Replace side cover.

IGNITOR

1. Remove upper shell and fan guard (See

Upper Shell Removal, page 13).

2. Remove fan (see page 13).

3. Remove the control side cover with a

5/16" nut driver. On 160, 175 and 220

models, remove two wheel support bolts

and nuts with a Phillips screwdriver and

an adjustable wrench. Remove side cover

(see Figure 14).

4. Disconnect ignitor wires from ignition

control assembly (see Figure 15). Pull

the ignitor wires up through the hole in

the lower shell.

5. Disconnect fuel line hose and air line

hose. Remove photocell from photocell

bracket (see Figure 15).

6. Remove combustion chamber. Stand

combustion chamber on end with nozzle

adapter bracket on top (see Figure 16).

www.usaprocom.com

160108-01C16

Figure 17 - Removing Air and Fuel Line

Hoses

Fuel Line

Hose

Air Line

Hose

Nozzle/

Adapter

Assembly

Combustion

Chamber

Photocell

Bracket

Nozzle

Adapter

Bracket

NOZZLE ASSEMBLY

1. Remove upper shell (see Upper Shell

Removal, page 13).

2. Remove fan (see Fan, page 13).

3. Remove fuel and air line hoses from

nozzle assembly (see Figure 17).

4. Turn nozzle assembly 1/4 turn to left and

pull toward motor to remove (see Figure

18).

5. Place plastic hex-body into vise and

lightly tighten.

6. Carefully remove nozzle from the nozzle

adapter using 5/8" socket wrench (see

Figure 19).

7. Blow compressed air through face of

nozzle. This will free any dirt in nozzle

area.

8. Inspect nozzle sleeve for damage.

9. Replace nozzle into nozzle adapter until

nozzle seats. Tighten 1/3 turn more using

5/8" socket wrench 4.5 to 5.1 N-m (40 to

45 in-lbs). See Figure 18.

10. Attach nozzle assembly to burner strap

(see Figure 18).

11. Attach fuel and airline hoses to nozzle

assembly.

12. Replace fan (see Fan, page 13).

13. Replace fan guard and upper shell (see

Upper Shell Removal, page 13).

Figure 18 - Removing Nozzle/Adapter

Assembly

Nozzle/

Adapter

Assembly

Combustion

Chamber

Figure 19 - Nozzle and Nozzle Adapter

Nozzle Face

Nozzle

Nozzle Sleeve

Nozzle

Adapter

Air Line

Fitting

Fuel Line

Fitting

(For 220 Model Only)

1. Remove combustion chamber and ignitor

by following steps 1 through 7 under Ig-

nitor, page 15.

2. Carefully place ignitor in a safe location.

3. Remove two nozzle adapter bracket

screws.

4. Place hex-shaped aluminum nozzle

adapter into vise (do not overtighten).

5. Carefully remove nozzle from nozzle

adapter using 5/8" socket wrench (see

Figure 19).

6. Blow compressed air through face of

nozzle. This will remove any debris in

nozzle.

7. Inspect nozzle seal for damage.

8. Replace nozzle into nozzle adapter

until nozzle seats. Tighten 80-110 inch-

pounds.

9. Attach nozzle adapter bracket to combus-

tion chamber with two screws removed in

step 3.

10. Repeat steps 9 through 16 under Ignitor,

page 15.

SERVICE PROCEDURES

www.usaprocom.com

17160108-01C

IGNITION CONTROL ASSEMBLY

WARNING: High voltage!

1. Unplug heater.

2. To expose the ignition control assembly,

remove the control panel side cover

screws using 5/16" nut-driver. On 160,

175 and 220 models, remove two wheel

support bolts and nuts with a Phillips

screwdriver and an adjustable wrench.

3. Remove fuse from fuse clips (see Figure

20).

4. Replace fuse with fuse of the same type

and rating (7A, 125VP). Do not substitute

a fuse with a higher current rating.

5. Replace control panel side cover.

Figure 20 - Replacing Fuse

Ignition

Control

Assembly

Fuse

PUMP ROTOR

(Procedure if Rotor is Binding)

1. Remove upper shell (see Upper Shell

Removal, page 13).

2. Remove filter end cover screws using

5/16" nut driver (see Figure 21).

3. Remove filter end cover and air filters.

4. Remove pump plate screws using 5/16"

nut-driver.

5. Remove pump plate.

6. Remove rotor, insert, and blades (see

Figure 22).

7. Check for debris in pump. If debris is

found, blow out with compressed air.

8. Install insert and rotor.

9. Check gap on rotor. Adjust to

0.076/0.101 mm (0.003"/0.004") if needed

(see Figure 22).

Note: Rotate rotor one full turn to ensure

the gap is 0.076/0.101 mm (0.003"/0.004")

at tightest position. Adjust if needed.

Figure 21 - Rotor Location

Pump

Plate

Insert

Rotor

Blade

Filter

End

Cover

Air

Intake

Filter

Air Output Filter

Gap Adjusting

Screw

Rotor

Blade

0.003"/0.004"

(0.076-0.101 mm)

Gap Measured

With Feeler

Gauge

Gap Adjusting Screw

Figure 22 - Gap Adjusting Screw

Locations

Sandpaper

Figure 23 - Sanding Rotor

10. Install blades, pump plate, air filters, and

filter end cover.

11. Replace fan guard and upper shell (see

Upper Shell Removal, page 13).

12. Adjust pump pressure (see Pump Pres-

sure Adjustment, page 14).

Note: If rotor is still binding, proceed as

follows.

13. Perform steps 1 through 6.

14. Place fine grade sandpaper (600 grit) on

flat surface. Sand rotor lightly in “figure 8”

motion four times (see Figure 23).

15. Reinstall insert and rotor.

16. Perform steps 10 through 12.

SERVICE PROCEDURES

www.usaprocom.com

160108-01C18

WIRING DIAGRAM

ST002-01

AIR GAUGE KIT

For all models. Special tool to check pump

pressure. 0-15 PSI gauge. 3/8" NPT pipe

thread.

ST001-01

IGNITION CONTROL ASSEMBLY/

PHOTOCELL TESTER

Special tool used to test the ignition control

assembly and photocell.

ACCESSORIES

Purchase these accessories from your local dealer. If they can not supply these accessories,

contact ProCom Heating, Inc. at 1-866-573-0674 for information. You can also write to the

address listed on the back page of this manual.

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact

ProCom Heating, Inc. at 1-866-573-0674. When calling, please have your model and serial

numbers of your heater ready.

You can also visit ProCom Heating, Inc.’s web site at www.usaprocom.com.

Blue

Main Return

Heater Control Assmebly

Blue

White

Black

Ignitor

Red

Photocell

Ignitor IGN

Motor MTR

Neutral AC

Line (L1) AC

Motor MTR

Ignitor IGN

Ground

Green

motor

Yellow or White

Yellow or

White

Power Plug

120V/60Hz

www.usaprocom.com

19160108-01C

PARTS

WHEEL AND HANDLES

1

3

5

4

6

7

8

9

10

2

ITEM PART # DESCRIPTION 110 160 175 220

1 160074-01 Rear Handle 1 1 1

2 160073-01 Front Handle 1 1 1

3 160072-01 Wheel Support Frame 2 2 2

4 160158-01 Support Bushing 2 2 2

5 160072-12 Fuel Tank Support Assembly 1 1 1

6 160072-13 Screw, M10-1.5 x 60 2 2 2

7 160129-01 Acorn Nut 2 2 2

8 160080-01 Wheel 2 2 2

9 160130-01 Wheel Spacer 2 2 2

10 160079-01 Axle 1 1 1

11 160062-01 Handle 1

12 160064-01 Front Handle Bracket 1

13 160064-02 Rear Handle Bracket 1

14 160083-01 Shell Heat Shield 1

15 160100-01 Screw, 10-16 x 2.0 1

16 160078-01 Screw, 10-16 x 0.5 1

11

13

14

15

16

12

MODELS

PCK160VT

PCK175VT

PCK220VT

MODEL

PCK110VT

www.usaprocom.com

160108-01C20

PARTS

MODELS PCK110VT, PCK160VT, PCK175VT AND PCK220VT

12

13

19

20

22

21

23

28

24

25

26

27

14

16

10

15

17

18

3

4

5

6

9

7

8

11

1

2

La page charge ...

Procom PCK110VT Manuel utilisateur

Procom PCK110VT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents