Allen-Bradley Flex integra 1793-IB16 Installation Instructions Manual

Taper
Installation Instructions Manual

Ce manuel convient également à

Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
FAST SHIPPING AND
DELIVERY
TENS OF THOUSANDS OF
IN-STOCK ITEMS
EQUIPMENT DEMOS
HUNDREDS OF
MANUFACTURERS
SUPPORTED
LEASING/MONTHLY
RENTALS
ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | sales@artisantg.com | www.artisantg.com
SM
View
Instra
FLEX I/O and FLEX Integra are trademarks
of Rockwell Automation
Publication 1793-5.8 - December 1999
Installation Instructions
FLEX Integra
16 Sink Input Module
(Cat. No. 1793-IB16 and -IB16S)
Module Installation
This module mounts on a DIN rail. It connects to an adapter or another
FLEX I/O or Integra module. Note: If using this module with FLEX I/O
modules, do not mount between FLEX I/O modules. Mount Integra
modules to the right of the FLEX I/O modules. To mount this module:
1. Remove the cover plug (if used) in the male connector of the unit to
which you are connecting this module.
2. Position the module on the 35 x 7.5mm DIN rail A (A-B pt. no.
199-DR1).
3. Rotate the module onto the DIN rail with the top of the rail hooked
under the lip on the rear of the module.
30869-M
A
A
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
2 FLEX Integra 16 Sink Input Module
Publication 1793-5.8 - December 1999
4. Press down to lock the module on the DIN rail.
If the module does not lock in place, use a screwdriver of similar
device to move the locking tab down, press the module flush with the
DIN rail and release the locking tab to lock the module in place.
5. Firmly push the module into the adjacent module/terminal base until
the units lock together.
6. Repeat the above steps to install the next module.
7. To remove an Integra module, you must work from the right side and
remove one module at a time. To disengage a module from its
neighbor, place a common flat-bladed screwdriver between the 2
modules and turn 1/4 turn to separate the modules.
8. Then slide the module away from its left neighbor, and release the
locking lever to remove the module from the DIN rail.
30870-M
30871-M
30872-M
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
FLEX Integra 16 Sink Input Module 3
Publication 1793-5.8 - December 1999
European Union Directive Compliance
If this product has the CE mark it is approved for installation within the
European Union and EEA regions. It has been designed and tested to meet
the following directives.
EMC Directive
This product is tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC) and the following standards, in
whole or in part, documented in a technical construction file:
EN 50081-2 EMC - Generic Emission Standard, Part 2 - Industrial Environment
EN 50082-2 EMC - Generic Immunity Standard, Part 2 - Industrial Environment
This product is intended for use in an industrial environment.
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC Low Voltage,
by applying the safety requirements of EN 61131-2 Programmable
Controllers, Part 2 - Equipment Requirements and Tests.
For specific information required by EN 61131-2, see the appropriate
sections in this publication, as well as the following Allen-Bradley
publications:
Industrial Automation Wiring and Grounding Guidelines For Noise Immunity,
publication 1770-4.1
Automation Systems Catalog, publication B111
This equipment is classified as open equipment and must be mounted in an
enclosure during operation to provide safety protection.
!
ATTENTION: Do not remove this module under
power. Removing this module under power will break the
electrical backplane (flexbus) connections. This can cause
personal injury or property damage by:
sending an erroneous signal to your system's field
devices causing unintended machine motion
causing an explosion in a hazardous environment
breaking communication to modules beyond this
module
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
4 FLEX Integra 16 Sink Input Module
Publication 1793-5.8 - December 1999
Wiring
This module is available with 2 styles of terminations: 1793-IB16 -
screw-cage and 1793-IB16S - spring-clamp. Refer to the wiring figure
below.
1. Connect individual sensor signal input leads to terminals 0 through 15
on row A (channels 0 thru 15 respectively).
2. Connect the associated sensor power lead to +24V dc on row (B).
3. Connect +24V dc voltage to V terminal on row B.
4. Connect 24V dc common to terminal COM on row A.
5. If daisy-chaining + 24V dc from this module to the next Integra
module, connect a jumper from terminal V to terminal 8 on the next 8
point Integra module or terminal V on the next 16 point Integra
module.
6. If daisy-chaining 24V dc common from this module to the next FLEX
Integra module, connect a jumper from terminal COM on this module
to terminal 0 on the next 8 point Integra module, or to terminal COM
on the next 16 point Integra module.
.
!
ATTENTION: Total current draw through the module’s
(V) voltage terminals is limited to 10A. Separate power
connections to the module may be required.
A
B
01 2345678 9101112131415COM
COM
VV
41816
0 12345 6789101112131415
A
B
41814
VV
COM
COM
1793-IB16
Where: COM = common, V = +24V dc power, 0 thru 15 = inputs
1793-IB16S
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
FLEX Integra 16 Sink Input Module 5
Publication 1793-5.8 - December 1999
Wiring Connections
Example of 2-wire and 3-wire Sensors
Channel Input Power Channel Input Power
00
connect to
corresponding
terminal on
row B
88
connect to
corresponding
terminal on row
B
11 99
2 2 10 10
3 3 11 11
4 4 12 12
5 5 13 13
6 6 14 14
7 7 15 15
+24V dc Power terminals V are internally connected together in the module.
24V dc
common
Common terminals COM are internally connected together in the
module.
A
B
01 2345678 9101112131415COM
COM
VV
41818
2-Wire Sensor
3-Wire Sensor
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
6 FLEX Integra 16 Sink Input Module
Publication 1793-5.8 - December 1999
Indicators
A = Status indicators - 0 through 15 - shows status of individual inputs
B = Insertable label for writing individual input designations
Memory Mapping
Bit/
Word
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Read I15 I14 I13 I12 I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0
Write Reserved DT 12-15 DT 00-11
Where:I = Input
DT = delay time - refer to “Setting the Input Delay Time”
1793-IB16
AB
0 1 2 3 4 5 6 7 8 9 10 11 14 1512 13
24 VDC SINK INPUT
41812
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
FLEX Integra 16 Sink Input Module 7
Publication 1793-5.8 - December 1999
Setting the Input Delay Time
You can select the input delay time (DT) for channels 00 thru 011, and
channels 12-15. Select the input delay time by setting the corresponding
bits in the output image table (complementary word) for the module.
For example, to set a delay time of 4ms for an input module at address rack
1, module group 0, set bits05, 04, 03, 02, 01 and 00 as shown below.
Input Delay Times
Important: Input and output wiring must be in accordance with Class I,
Division 2 wiring methods and in accordance with the
authority having jurisdiction.
02 01 00 Filter Time for Inputs 00-11
Selected
Filter Time
05 04 03 Filter Time for Inputs 12-15
000Filter Time 0 (default) 250
μ
s
001Filter Time 1 500
μ
s
010Filter Time 2 1ms
011Filter Time 3 2ms
100Filter Time 4 4ms
101Filter Time 5 8ms
110Filter Time 6 16ms
111Filter Time 7 32ms
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
100
= 44 Octal or 36 decimal
Write delay time on system startup.
Write DT to complement
of input module.
Fill File
Source
Destination
Length
3
#O:010
1
I:000
00
FLL
O:010
Dec.
41335B
100
DT 00-11
DT 12-15
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
8 FLEX Integra 16 Sink Input Module
Publication 1793-5.8 - December 1999
C-UL and UL Hazardous Location Approval
Approbation d’utilisation dans des
environnements dangereux par la C-UL and UL
C-UL and UL certifies products for general use as
well as for use in hazardous locations. Actual
C-UL and UL certification is indicated by the
product label as shown below, and not by
statements in any user documentation.
La C-UL and UL certifie des produits pour une
utilisation générale aussi bien que pour une
utilisation en environnements dangereux. La
certification C-UL and UL en vigueur est indiquée
par l'étiquette produit et non par des indications
dans la documentation utilisateur.
Example of the
C-UL and UL
certification
product label
Exemple
d'étiquette de
certification d'un
produit par la
C-UL and UL
To comply with C-UL and UL certification for use
in hazardous locations, the following information
becomes a part of the product literature for this
C-UL and UL-certified industrial constrol product.
This equipment is suitable for use in Class
I, Division 2, Groups A, B, C, D, or
non-hazardous locations only.
The products having the appropriate C-UL
and UL markings (that is, Class I, Division 2,
Groups A, B, C, D) are certified for use in
other equipment where the suitability of
combination (that is, application or use) is
determined by the C-UL and UL or the local
inspection office having jurisdiction
Peripheral equipment must be suitable for
the location in which it is used.
EPour satisfaire à la certification C-UL and UL en
environnements dangereux, les informations
suivantes font partie intégrante de la
documentation des produits de commande
industrielle certifiés.
Cet équipement ne convient qu’à une
utilisation dans
des environnements de Classe I, Division 2,
Groupes A, B, C, D ou non dangereux.
Les produits portant le marquage C-UL and
UL approprié (c'est-à-dire Classe I, Division
2, Groupes A, B, C, D) sont certifiés pour une
utilisation avec d'autres équipements, les
combinaisons d’applications et d’utilisation
étant déterminées par la C-UL and UL ou le
bureau local d'inspection.
L'équipement périphérique doit convenir à
l'emplacement d'utilisation.
Important: Due to the modular nature of a
programmable control system, the
product with the highest temperature
rating determines the overall
temperature code rating of a
programmable control system in a Class
I, Division 2, location. The temperature
code rating is marked on the product
label as shown.
Important: De par la nature modulaire des systèmes de
commande programmables, le produit
ayant le code de température le plus éle
détermine le code de température global du
système dans un environnement de Classe
I, Division 2. Le code de température est
indiqué sur l'étiquette produit.
The following warnings apply to products having
C-UL and UL certification for use in hazardous
locations.
Les avertissements suivants s'appliquent aux
produits ayant la certification C-UL and UL pour une
utilisation dans des environnements dangereux.
CUS
CUS
LISTED
CL I, DIV 2
GP A,B,C,D
TEMP
CL I, DIV 2
GP A,B,C,D
TEMP
Look for temperature
code rating here.
CUS
LISTED
Le code de température
est indiqué ici.
CUS
LISTED
CL I, DIV 2
GP A,B,C,D
TEMP
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
FLEX Integra 16 Sink Input Module 9
Publication 1793-5.8 - December 1999
C-UL and UL Hazardous Location Approval
Approbation d’utilisation dans des
environnements dangereux par la C-UL and UL
WARNING: Explosion Hazard
Substitution of components may impair
suitability for Class I, Division 2.
Do not replace components unless power
has been switched off or the area is known
to be non-hazardous.
Do not disconnect equipment unless power
has been switched off or the area is known
to be non-hazardous.
Do not disconnect connectors unless
power has been switched off or the area is
known to be non-hazardous. Secure any
user-supplied connectors that mate to
external circuits on this equipment by using
screws, sliding latches, threaded
connectors, or other means such that any
connection can withstand a 15 Newton (3.4
lb.) separating force applied for a minimum
of one minute.
Batteries must only be changed in an area
known to be non-hazardous.
La substitution de composants peut rendre ce
matériel inadapté à une utilisation en
environnement de
Classe I, Division 2.
Couper le courant ou s'assurer que
l’environnement est classé non dangereux
avant de remplacer des composants.
Couper le courant ou s’assurer que
l’environnement est classé non dangereux
avant de débrancher l'équipement.
Couper le courant ou s'assurer que
l’environnement est classé non dangereux
avant de débrancher les connecteurs. Fixer
tous les connecteurs fournis par l'utilisateur
pour se brancher aux circuits externes de cet
appareil à l 'aide de vis, loquets coulissants,
connecteurs filetés ou autres, de sorte que les
connexions résistent à une force de séparation
de 15 Newtons (1,5 kg - 3,4 lb.) appliquée
pendant au moins une minute.
S'assurer que l'environnement est classé non
dangereux avant de changer les piles.
C-UL and UL logo is a registered trademark of the
Underwriters Laboratories.
Le sigle C-UL and UL est une marque déposée de
la Underwriters Laboratories.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
10 FLEX Integra 16 Sink Input Module
Publication 1793-5.8 - December 1999
Specifications - 16 Input Module Cat. No. 1793-IB16 and -IB16S
Module Type 16 digital input - sinking
1793-IB16 - screw-cage terminations
1793-IB16S - spring-clamp terminations
Module Location DIN rail mounting
Number of Channels 16 (1 group of 16, nonisolated, sinking)
On-state Voltage 10V dc minimum
24V dc nominal
31.2V dc maximum
On-state Current 2mA minimum
8.8mA nominal at 24V dc
12.1mA maximum
Off-state Voltage 5V dc maximum
Off-state Current 1.5mA minimum
Input Impedance 2.5K
Ω
maximum
Isolation Voltage 100% tested at 850V dc for 1s between user and system.
No isolation between individual channels
Input Filter Time - selectable
Off to On
On to Off
Minimum 1ms plus selected filter time of:
250
μ
s, 500
μ
s, 1ms, 2ms, 4ms, 8ms, 16ms, or 32ms
250
μ
s, 500
μ
s, 1ms, 2ms, 4ms, 8ms, 16ms, or 32ms
Default = 250
μ
s selectable thru output image table
Flexbus Current 25mA maximum
Power Dissipation 6.1W @ 31.2V dc
Thermal Dissipation 20.8 BTU/hr @ 31.2V dc
Indicators 16 yellow channel status indicators
External dc Power Voltage 19.2-31.2V dc (5% ac ripple)
See Derating Curve.
Dimensions Inches
(Millimeters)
2.72H x 3.7D x 3.2W
(69H x 94D x 80W)
Environmental Conditions
Operational Temperature
Storage Temperature
Relative Humidity
Shock Operating
Nonoperating
Vibration
0 to +55
o
C (32 to +131
o
F)
-40 to +85
o
C (-40 to +185
o
F)
5 to 95% noncondensing
Tested to 30g peak acceleration, 11(+
1)ms pulse width
Tested to 50g peak acceleration, 11(+
1)ms pulse width
Tested 5g @ 10-500Hz per IEC68-2-6
Conductors Wire Size
Category
12 gauge to 18 gauge (4mm
2
to 0.75mm
2
)
stranded wire rated @ 75
o
C minimum
3/64 in (1.2mm) maximum insulation
2
1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
FLEX Integra 16 Sink Input Module 11
Publication 1793-5.8 - December 1999
Derating Curve
Screw Terminal Torque 5-7 lb-in (0.5-0.6Nm)
Agency Certification
(when product is marked)
C-UL Listed
C-UL Class I, Division 2 Groups A, B, C and D certified
•UL listed
CE marked for all applicable directives
C-Tick marked for all applicable acts.
1Use this category information for planning conductor routing as described in publication 1770-4.1, “Wiring and
Grounding Guidelines for Noise Immunity.”
Specifications - 16 Input Module Cat. No. 1793-IB16 and -IB16S
31.2
30
25
20
15
10
0
10 20 30 40 50 55 6037
27.5
Vin
On-State
Voltage
(V dc)
41820
Ambient Temperature (
o
C)
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Publication 1793-5.8 - December 1999 PN 957259-15
Supersedes publication 1793-5.8 - September 1999 © (1999) Rockwell International Corporation.Printed in USA
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
FAST SHIPPING AND
DELIVERY
TENS OF THOUSANDS OF
IN-STOCK ITEMS
EQUIPMENT DEMOS
HUNDREDS OF
MANUFACTURERS
SUPPORTED
LEASING/MONTHLY
RENTALS
ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | sales@artisantg.com | www.artisantg.com
SM
View
Instra
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Allen-Bradley Flex integra 1793-IB16 Installation Instructions Manual

Taper
Installation Instructions Manual
Ce manuel convient également à

dans d''autres langues