Motorola vap2400 Guide d'installation

Marque: Motorola

Modèle: vap2400

Catégorie: Des ponts

Taper: Guide d'installation

VAP2400

Wireless Video Bridge

MOTOROLA and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC. All other product or service

No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation,

transformation, or adaptation) without written permission from Motorola, Inc. Motorola reserves the right to revise this publication and to make

changes in content from time to time without obligation on the part of Motorola to provide notiﬁcation of such revision or change. Motorola

provides this guide without warranty of any kind, implied or expressed, including, but not limited to, the implied warranties of merchantability

and ﬁtness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time.

VAP2400 Wireless Video Bridge • Installation Manual iii

Contents

INSTALLATION AND OVERVIEW ....................................................... 5

About this Manual ................................................................................ 6

Box Contents ........................................................................................ 6

Front Panel ............................................................................................ 7

Rear Panels ........................................................................................... 8

Installing Your VAP2400 (Dual Units) ..................................................... 9

Step 1: Install the Access Point ....................................................... 9

Step 2: Install the Client .................................................................. 10

Installing Additional VAP2400 Clients ................................................... 12

TROUBLESHOOTING .......................................................................... 15

Solutions ............................................................................................... 15

SAFETY AND COMPLIANCE .............................................................. 17

VAP2400 Wireless Video Bridge • Installation Manual 5

Installation and Overview

The VAP2400 enables you to transmit multiple standard- and high-deﬁnition video streams throughout your home

wirelessly. You can enjoy a full range of video services and applications without having to run wires, lay cables,

or drill holes. The VAP2400 uses one-button, Wi-Fi Protected Setup (WPS) technology to ensure easy, reliable

installation.

The VAP2400 operates via two (or more) integrated units. You’ll dedicate one unit as the Access Point and

the other unit (or units) as its Client. When you connect a VAP to your home gateway, it auto-conﬁgures as an

Access Point. The Access Point streams content to the Client, which you’ll connect to a secondary set-top in

a different location in your home. (The Client auto-conﬁgures as well when you connect it to the set-top.) The

following graphic illustrates this setup:

Room 1

Room 2

Secondary Set-top

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 6

About this Manual

This manual provides you with instructions on how to install your VAP2400 series video bridge. Motorola

designed the VAP2400 series to install and integrate easily with your set-top box and home network. If you

encounter any difﬁculties during the installation process, refer to the Troubleshooting section at the end of this

manual.

Box Contents

Your box should contain the following:

Single Unit Bundle (for additional Clients)

Dual Unit Bundle (for initial installation)

One VAP2400 Series

connection kit

Two VAP2400 Series

connection kits

One Ethernet Cable

Two Ethernet Cables

One Power Adapter Two Power Adapters

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 7

Front Panel

1 Power Green = The VAP is on

Amber = The VAP is on standby

Off = The VAP is off or disconnected from its power source

2 Wireless Link Quality Solid Green = Wireless quality is good

Flashing Green = Wireless quality is average

Off = No wireless connection

3 Operational Mode Solid Green = The VAP is functioning as an Access Point

Solid Amber = The VAP is functioning as a Client

Blinking Amber = There is an error. Refer to “Troubleshooting” for more

details.

Off = The automatic conﬁguration process has failed

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 8

Rear Panels

Four Port

Single Port

1 Reset Button Resets the VAP to its default settings

2 WPS Button Establishes wireless connection to your home network

3 Ethernet Port Connects to an Ethernet-equipped computer, hub, or switch using an

RJ-45 cable connection

4 Power Jack Provides power to the VAP2400

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 9

Installing Your VAP2400 (Dual Units)

Follow the instructions below to install your Access Point and Client.

Step 1: Install the Access Point

1. Connect one VAP unit to your Home Gateway using the provided Ethernet cable. Before you connect the

VAP, ensure the Gateway is powered on.

2. Connect the power adapter to the VAP and plug the adapter into a wall outlet. You’ll see the power LED

on the unit’s front panel light green, indicating the unit is powered:

. Check to ensure the operational

mode LED lights green, indicating the VAP is functioning as an Access Point.

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 10

Step 2: Install the Client

1. Connect the second VAP unit to your secondary set-top box with the provided Ethernet cable. Before you

connect the VAP, ensure your set-top box is powered on.

Note: While you are required to connect your VAP to a set-top box to ensure the Access Point properly

streams video to the client, the VAP’s extra Ethernet ports provide you with the option of connecting other

devices to the unit as well, such as computers and gaming consoles.

2. Connect the power adapter to the VAP and plug the adapter into a wall outlet. You’ll see the power LED on

the unit’s front panel light green, indicating the unit is powered:

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 11

3. Wait 60 seconds after powering the VAP, and then press and hold the WPS button on the back of the Client

for two seconds. After doing so, you will have two minutes to return to the Access Point and press and

hold its WPS button. Pressing the buttons on both units enables them to establish a wireless connection.

Note: After you press the WPS button, the LED below it ﬂashes green. If your connection is successful,

the LED will stop ﬂashing, light solid green for approximately ﬁve minutes, and then extinguish. This is a

normal part of the process and does not mean you have lost your connection to the Access Point. If the

LED connection continues ﬂashing, it indicates the unit has experienced an error. If this occurs, refer to

Troubleshooting, page 16.

4. The Client’s Wireless link LED lights green:

. You have now established a secure wireless connection

between the Access Point and the Client. Check to ensure the operational mode LED lights amber,

indicating the VAP is functioning as a Client. You now can begin streaming video content to your secondary

set-top box or boxes.

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 12

Installing Additional VAP2400 Clients

Once you’ve installed your Access Point to your home gateway and established a wireless connection with your

Client, you can install additional VAP clients throughout your home. Follow the instructions below for each single

client unit you wish to install.

1. Connect the VAP to your secondary set-top box with the provided Ethernet cable. Before you connect the

VAP, ensure your set-top box is powered on.

Note: While you are required to connect your VAP to a set-top box to ensure it properly transfers video

throughout your home, the VAP’s extra Ethernet ports provide you with the option of connecting other

devices to the unit as well, such as computers and gaming consoles.

2. Connect the power adapter to the VAP and plug the adapter into a wall outlet. You’ll see the power LED on

the unit’s front panel light green, indicating the unit is powered:

Installation and Overview

VAP2400 Wireless Video Bridge • Installation Manual 13

3. Wait 60 seconds after powering the VAP, and then press and hold the WPS button on the back of the Client

for two seconds. After doing so, you will have two minutes to return to the Access Point and press and

hold its WPS button. Pressing the buttons on both units enables them to establish a wireless connection.

Note: After you press the WPS button, the LED below it ﬂashes green. If your connection is successful,

the LED will stop ﬂashing, light solid green for approximately ﬁve minutes, and then extinguish. This is a

normal part of the process and does not mean you have lost your connection to the Access Point. If the

LED connection continues ﬂashing, it indicates the unit has experienced an error. If this occurs, refer to

Troubleshooting, page 16.

4. After the VAP establishes a wireless connection with your set-top box, the Wireless link LED lights: .

Check to ensure the operational mode LED lights amber, indicating the VAP is functioning as a Client. Your

VAP is now ready to stream content to the device equipped with the VAP adapter.

VAP2400 Wireless Video Bridge • Installation Manual 15

Troubleshooting

If you cannot ﬁnd a solution to your problem in this manual, or to otherwise get assistance with your VAP2400,

contact your service provider.

Solutions

If the solutions listed here do not solve your problem, try pressing the Reset button on the rear panel of the

Access Point and/or Client. Pressing and immediately releasing the Reset button resets the VAP to its current

settings. Pressing and holding the Reset button for more than ﬁve seconds will perform a factory default reset,

which you should do only if directed to do so by a technical service representative.

Problem Possible Solution

Power LED is off Check that the VAP2400 is properly plugged into the electrical outlet.

Check that the electrical outlet is working.

Press and immediately release the Reset button.

Cannot send or receive data Check that the Ethernet cable is properly connected to both the VAP2400 and your home

gateway/device.

Ensure you have not experienced an interruption in your cable or Internet service.

Ensure your home gateway is connected and functioning.

VAP cannot locate network Locate the WPS button on the VAP’s back panel. Press and hold the button until the

Wireless Link Quality LED lights solid green.

Operational Mode LED is blinking

amber

Access Point: Unplug the unit. Restart your gateway. After the gateway boots, plug in the

unit and wait for the LED to light green.

Client: If the LED continues blinking for more than 60 seconds, unplug the unit and then

plug it back into the outlet.

Troubleshooting

VAP2400 Wireless Video Bridge • Installation Manual 16

Rapidly blinking WPS LED If the LED remains in this state for longer than two minutes, go to the unit’s back panel

and push the WPS button. The LED may continue ﬂashing in a different pattern, rapidly

blinking for 1 second and then resting brieﬂy before blinking again. If this occurs, wait

one to two minutes and then press the WPS button again.

Cannot conﬁgure a VAP unit as an

Access Point

If you cannot establish one of your units as an Access Point, it may indicate that your

router is not connected to your service provider’s network. (The operational mode LED

lights green on VAP units dedicated as Access Points and amber on VAP units dedicated

as Clients; see pp. 9–11 for more details.) If you experience this problem, contact your

service provider for assistance.

VAP2400 Wireless Video Bridge • Installation Manual 17

Safety and Compliance

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE UNIT MUST NOT BE

EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT.

CAUTION: TO ENSURE REGULATORY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES.

CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND

TROUBLESHOOTING INSTRUCTIONS. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.

This device must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation

that comes with the product.

Postpone router installation until there is no risk of thunderstorm or lightning activity in the area.

Do not overload outlets or extension cords, as this can result in a risk of ﬁre or electric shock. Overloaded AC outlets, extension cords,

frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or ﬁre hazard.

Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular

attention to cords where they are attached to plugs and convenience receptacles, and examine the point where they exit from the product.

Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the power cord.

Place this equipment on a stable surface.

When using this device, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and injury to persons,

including the following:

• Read all of the instructions {listed here and/or in the user manual} before you operate this equipment. Give particular attention to all

safety precautions. Retain the instructions for future reference.

• Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols that are afﬁxed to this

equipment.

• Comply with all instructions that accompany this equipment.

Safety and Compliance

VAP2400 Wireless Video Bridge • Installation Manual 18

• Avoid using this product during an electrical storm. There may be a risk of electric shock from lightning. For added protection for this

product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet, and

disconnect the cable system. This will prevent damage to the product due to lightning and power surges.

• Operate this product only from the type of power source indicated on the product’s marking label. If you are not sure of the type of

power supplied to your home, consult your dealer or local power company.

• Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the

product is in safe operating condition.

It is recommended that the customer install an AC surge protector in the AC outlet to which this device is connected. This is to avoid

damaging the equipment by local lightning strikes and other electrical surges.

Different types of cord sets may be used for connections to the main supply circuit. Use only a main line cord that complies with all

applicable product safety requirements of the country of use.

Installation of this product must be in accordance with national wiring codes.

Place unit to allow for easy access when disconnecting the power cord/adapter of the device from the AC wall outlet.

Wipe the unit with a clean, dry cloth. Never use cleaning ﬂuid or similar chemicals. Do not spray cleaners directly on the unit or use forced

air to remove dust.

This product was qualiﬁed under test conditions that included the use of the supplied cables between system components. To be in

compliance with regulations, the user must use these cables and install them properly. Connect the unit to a grounding type AC wall outlet

using the power adapter supplied with the unit.

Do not cover the device, or block the airﬂow to the device with any other objects. Keep the device away from excessive heat and humidity

and keep the device free from vibration and dust.

Installation must at all times conform to local regulations.

FCC ComplianCe Class B Digital DeviCe

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

Safety and Compliance

VAP2400 Wireless Video Bridge • Installation Manual 19

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modiﬁcations not expressly approved by Motorola for compliance could void the user’s authority to operate the

equipment.

impoRtant note:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed

and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The availability of some speciﬁc channels and/or operational frequency bands are country dependent and are ﬁrmware programmed at the

factory to match the intended destination. The ﬁrmware setting is not accessible by the end user.

CanaDian ComplianCe

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareil

numérique de la classe B respects toutes les exigences du Règlement sur le matériel brouilleur du Canada.

FCC DeClaRation oF ConFoRmity

Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044, 1-215-323-1000, declares under sole

responsibility that the VAP2400 complies with 47 CFR Parts 2 and 15 of the FCC Rules as Class B digital devices. These devices comply

with Part 15 of FCC Rules. Operation of these devices is subject to the following two conditions: (1) These devices may not cause harmful

interference, and (2) these devices must accept any interference that may cause undesired operation.

WiReless lan inFoRmation

The VAP2400 products are wireless network products that use Orthogonal freguency-division multiplexing (OFDM) radio technology. These

products are designed to be inter-operable with any other wireless OFDM type product that complies with:

Safety and Compliance Safety and Compliance

VAP2400 Wireless Video Bridge • Installation Manual 20

• The IEEE 802.11 Standard on Wireless LANs (Revision A and Revision N), as deﬁned and approved by the Institute of Electrical

Electronics Engineers.

• The Wireless Fidelity (WiFi) certiﬁcation as deﬁned by the Wi-Fi Alliance.

WiReless lan anD youR HealtH

The VAP2400, like other radio devices, emit radio frequency electromagnetic energy, but operate within the guidelines found in radio

frequency safety standards and recommendations.

RestRiCtions on use oF WiReless DeviCes

In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible

representatives of the organization. For example, using wireless equipment in any environment where the risk of interference to other

devices or services is perceived or identiﬁed as harmful.

If you are uncertain of the applicable policy for the use of wireless equipment in a speciﬁc organization or environment, you are

encouraged to ask for authorization to use the device prior to turning on the equipment.

The manufacturer is not responsible for any radio or television interference caused by unauthorized modiﬁcation of the devices included

with this product, or the substitution or attachment of connecting cables and equipment other than speciﬁed by the manufacturer.

Correction of interference caused by such unauthorized modiﬁcation, substitution, or attachment is the responsibility of the user.

The manufacturer and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may

arise from failing to comply with these guidelines.

FCC CeRtiFiCation

The VAP2400 contains a radio transmitter and accordingly has been certiﬁed as compliant with 47 CFR Part 15 of the FCC Rules for

intentional radiators. Products that contain a radio transmitter are labeled with FCC ID and the FCC logo.

inDustRy CanaDa (iC) statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement

La page est en cours de chargement...

Motorola vap2400 Guide d'installation

Marque: Motorola

Modèle: vap2400

Catégorie: Des ponts

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Motorola vap2400 Installation guide

Motorola vap2400 Guide d'installation

Motorola vap2400 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents