VTech VNT832 Manuel utilisateur

Go to

businessphones.vtech.com

to register your product for

enhanced warranty support and

the latest VTech product news.

VNT832

4-Port Ethernet Router

User’s manual

Congratulations

on your purchase of this VTech product. Before using this product,

please read the Important safety information.

This user’s manual provides you with the complete installation,

setup and operation instructions.

For customer service or product information, visit our website at

businessphones.vtech.com or call 1 (888) 370-2006.

Model number: VNT832

Type: 4-Port Ethernet Router

Serial number: __________________________________

Purchase date: __________________________________

Place of purchase: __________________________________

Both the model and serial numbers of your VTech product can be

found on the bottom of the router.

Save your sales receipt and original packaging in case it is

necessary to return your router for warranty service.

i

Important Safety Information

When using your equipment, basic safety precautions should always be followed

to reduce the risk of re, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Do not use this product near water such as near a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

3. Do not place this product on an unstable table, shelf, stand or other unstable

surfaces.

4. CAUTION: Use only the adapters included with this product. Incorrect adapter

polarity or voltage can seriously damage the product.

Power adapter: Input 100–240V AC 500mA 50/60Hz; Output: 12V DC 1000mA.

5. The power adapters are intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

6. For pluggable equipment, the socket-outlet shall be installed near the

equipment and shall be easily accessible.

7. Unplug this product from the wall outlet before cleaning. Do not use liquid or

aerosol cleaners. Use a damp cloth for cleaning.

8. Do not cut off the power adapters to replace them with other plugs, as this

causes a hazardous situation.

9. Do not allow anything to rest on the power cords. Do not install this product

where the cords may be walked on or crimped.

10. This product should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power supplied at the

premises, consult your dealer or local power company.

11. Do not overload wall outlets or use an extension cord.

12. This product should not be placed in any area where proper ventilation is

not provided. Slots and openings in the back or bottom of this product are

provided for ventilation. To protect them from overheating, these openings

must not be blocked by placing the product on a soft surface such as a bed,

sofa or rug. This product should never be placed near or over a radiator or

heat register.

13. Never push objects of any kind into this product through the slots because

they may touch dangerous voltage points or create a short circuit. Never spill

liquid of any kind on the product.

14. To reduce the risk of electric shock, do not disassemble this product, but take

it to an authorized service facility. Opening or removing parts of the product

other than specied access doors may expose you to dangerous voltages or

other risks. Incorrect reassembling can cause electric shock when the product

is subsequently used.

15. Periodically examine all components for damage.

SAVE THESE INSTRUCTIONS

ii

Important Safety Information

Electromagnetic elds (EMF)

This VTech product complies with all standards regarding

electromagnetic elds (EMF). If handled properly and according to

the instructions in this user’s manual, the product is safe to be used

based on scientic evidence available today.

Parts checklist

Your router package contains the following items. Save your sales

receipt and original packaging in the event warranty service is

necessary.

RouterAbridged user’s

manual

Ethernet cable Power adapter

Go to

businessphones.vtech.com

to register your product for

enhanced warranty support and

the latest VTech product news.

User’s manual

VNT832

4-Port Ethernet Router

1

Table of Contents

Important Safety Information ... i

Parts checklist .........................ii

Getting started ........................3

Router Overview .......................... 3

Connect your system ...................5

Congure your computer network .6

For Windows XP/2000 ............... 6

For Windows Vista/7/8 ............... 9

Connecting wireless devices ........12

Manual connection .................... 12

Using WPS ................................ 12

Congure your router .............13

Log in to the web management

page ..........................................13

Web management page

overview ....................................14

Fast conguration .......................15

Status ........................................16

Device info: Wireless Router

Status ........................................ 16

Statistics .................................... 17

Setup ......................................... 18

WAN: WAN Conguration ......... 18

LAN: LAN Interface Setup ........ 20

LAN: DHCP mode: .................... 21

LAN: DHCP Static IP

Conguration ............................. 23

WLAN: Wireless Basic

Settings ...................................... 24

WLAN: Wireless Security

Setup ......................................... 25

WLAN: Wireless Multiple

BSSID Setup ............................. 27

WLAN: Wireless Access

Control ....................................... 28

WLAN: Wireless Advanced

Settings ...................................... 29

WLAN: Wi-Fi Protected Setup .. 31

WLAN: WDS Settings ............... 32

Advanced ...................................33

Route: Routing conguration .... 33

Route: RIP Conguration .......... 34

NAT: DMZ .................................. 35

NAT: Virtual server ..................... 36

NAT: ALG ................................... 37

NAT: NAT port trigger ................ 38

NAT: NAT IP mapping ............... 39

QoS: IP QoS .............................. 40

QoS: IP QoS trafc shaping: ..... 41

Port Mapping Conguration ...... 42

Others: Bridge Setting ............... 43

Others: Client limit

conguration .............................. 44

Others: Telnet ............................ 44

Service ......................................45

UPnP ......................................... 45

DNS Conguration .................... 46

2

Dynamic DNS Conguration..... 47

USB Storage ............................. 48

Firewall ......................................49

MAC lter ................................... 49

IP/Port lter ................................ 50

URL lter .................................... 52

DoS ............................................ 53

Maintenance ..............................54

Update: Upgrade rmware ....... 54

Update: Backup/restore

settings: ..................................... 56

Password: User account

conguration .............................. 58

Reboot ....................................... 60

Time ........................................... 61

Log: Log setting ......................... 62

Diagnostics: Ping ...................... 62

Diagnostics: Traceroute ............ 63

Diagnostics: Diagnostic test ...... 64

Appendix ................................65

Frequently asked questions ......... 65

FCC part 15 ...............................66

For cETL compliance only ...........67

Mesures de sécurité

importantes ................................ 67

For cETL compliance only ...........68

Limited Warranty.........................69

Technical specications ............... 71

3

Getting started

Router Overview

1– On/Off light

• On when the router is powered on.

2– USB light

• On when there is a device connected to the USB port.

• Flashes when the USB port receives data

• Off when no device is connected to the USB port.

3– WAN light

• On when the Internet connectivity is established as the WAN port is

connected to Internet.

4– light

• On when any LAN port is connected.

• Flashes when any LAN port receives data.

5– Wi-Fi light

• On when the Wi-Fi is turned on.

• Off when the Wi-Fi is turned off.

6– light

• On when WPS is in progress.

• Off when the WPS is not in progress.

11 12 13 14 15 16 17 18 19

1

2

3 4

5

6

7

8 9 10 11

12

13

2 3 4 5 6 7 8 9

20

10

4

Getting started

Router Overview

7–USB port

• Connects to USB device for le sharing.

8–Power jack

• Connects to the power adapter.

9– On/Off button

• Press to power on the router.

• Press once again to power it off.

10–LAN ports

• Connect to Ethernet devices such as computers and SIP phones.

11–WAN port

• Connects to the wide area network.

12–RESET button

• Press and hold (using a narrow-pointed object) to reset the router to

default settings.

13–WPS button

• After turning on the Wi-Fi, press and hold for 10 seconds to start

the Wireless Protected Setup (WPS).

11 12 13 14 15 16 17 18 19

1

2

3 4

5

6

7

8 9 10 11

12

13

2 3 4 5 6 7 8 9

20

10

WPS

5

Getting started

Connect your system

The VNT832 router has four LAN ports for connecting Ethernet

devices such as computers and SIP phones. Before you start setting

up your system, plan it carefully. Consider the number of Ethernet

device(s) you need to connect before you start planning your system.

NOTES

• Use only the adapter provided.

• Make sure the electrical outlet is not controlled by a wall switch.

• The adapter is intended to be correctly oriented in a vertical or oor mount

position. The prongs are not designed to hold the plug in place if it is plugged into

a ceiling, under-the-table or cabinet outlet.

To power on, press the button at the back of the router. The

light will turn on.

Connects to

Computer

Connects to

SIP Phone

Power

on/off

button

Connects

to power

Connects to the

internet via

Cable/DSL Modem

WPS

6

Getting Started

Congure your computer network

In order to view or change the settings of the VNT832 router, you

need to login to the web management page of the router. Before

that, connect your computer to the LAN port of the router, and then

set the computer to obtain IP address automatically according to the

steps below.

For Windows XP/2000

1. Click Start, then open the Control Panel.

2. Double-click Network Connections.

7

Getting Started

Congure your computer network

3. Right-click Local Area Connection, and then select Properties.

4. Select Internet Protocol (TCP/IP), and then click Properties.

8

Getting Started

Congure your computer network

5. Select Obtain IP address automatically and Obtain DNS

server address automatically, and then click OK.

9

Getting Started

Congure your computer network

For Windows Vista/7/8

1. Click Start, and then open the Control Panel.

2. Click Network and Internet, and then Network and Sharing Center.

10

Getting Started

Congure your computer network

3. Click Change adapter settings.

4. Right-click Local Area Connection, and then select Properties.

11

Getting Started

Congure your computer network

5. Select Internet Protocol Version 4 (TCP/IPv4), and then click

Properties.

6. Select Obtain an IP address automatically and Obtain DNS

server address automatically, and then click OK.

12

Getting Started

Connecting wireless devices

Before you connect wireless devices to the router, you should run the

fast conguration Wizard. See “Fast conguration” on page 15.

You can connect wireless devices manually or by using WPS, which

is fast and convenient.

Manual connection

1. On your wireless device, open your Network or Wi-Fi settings

and nd the list of available Wi-Fi networks.

2. Find the network name (SSID) for your VNT832 router. If you

have trouble identifying the SSID, it is printed on the label on the

bottom of the router.

3. On your device, select the network and enter the Wi-Fi

password, which is also printed on the label on the bottom of the

router.

4. On your device, click Connect.

Using WPS

1. On the router, press and hold the Wi-Fi/WPS button for 10

seconds.

The WPS light on the front panel turns on, and you will have two

minutes to complete the rest of this procedure.

2. On your device, nd your WPS settings and turn WPS on.

Your device will connect to the network. If your device requests

a WPS PIN, the WPS PIN is printed on the label on the bottom

of the router.

To congure additional WPS settings for the router, see “WLAN: Wi-

Fi Protected Setup” on page 31.

13

Congure your router

Log in to the web management page

With your computer connected to a LAN port of the router and set to

obtain an IP address automatically, power on the router. You can log

in to the web management page to browse the router settings and

change them if necessary.

TIP

• Before you browse the web management page, check your browser’s network

setting. Make sure you do not use a proxy server for LAN setting.

1. Open a web browser on your computer.

2. Type http://192.168.1.1 in the address bar, and then press

Enter. The following login page displays.

3. Enter the default user name and password for the administrative

account as shown below. The user name and password are

case-sensitive.

Username: admin

Password: 12345

4. Click Login to enter the web management page of the router.

NOTE

• Both administrative account and normal user account can view the router

settings. To change the settings, you must login using an administrative account.

14

Congure your router

Web management page overview

After you logged in to the web management page, you can do the

congurations of your router here. You will see the menus for Status,

Wizard, Setup, Advanced, Service, Firewall, and Maintenance.

• STATUS: Allows you to view the information and statistics of the

router.

• WIZARD: Allows you to start the fast conguration Wizard.

• SETUP: Allows you to congure the basic functions of the router.

• ADVANCED: Allows you to congure the advanced functions of

the router.

• SERVICE: Allows you to congure extended network features.

• FIREWALL: Allows you to secure your router from unauthorized

devices and/or services.

• MAINTENANCE: Allows you to manage rmware updates,

passwords, network time, and diagnostics.

15

Congure your router

Fast conguration

The Wizard feature can guide you through the basic conguration of

the router step by step. After running the Wizard you can close the web

management page and then start connecting devices to the router.

1. Click the Wizard menu to start the fast conguration.

2. Select or input the information on the page as appropriate to

congure the WAN settings. Click Next to proceed.

3. Preview the settings and click Apply Changes to save the

settings. Otherwise, click Prev to return to the previous page or

click Cancel to cancel the fast conguration.

16

Congure your router

Status

The Status menu allows you to view the information and statistics of

the router. Choose this menu and you can see the next sub-menus:

Device info and Statistics.

Device info: Wireless Router Status

Click the Status menu. The Wireless Router Status page under the

Device info sub-menu in the left pane opens, displaying the basic

information of the router, including system, LAN conguration, DNS

status and Ethernet WAN interfaces.

La page charge ...

VTech VNT832 Manuel utilisateur

VTech VNT832 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents