INSTALLATION INSTRUCTIONS
CPU Enclosure - Pipe Mount Accessory
CMA170
CMA170 Installation Instructions
2
DISCLAIMER
CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components does not exceed the weight capacity of the
mount.
•The weight capacity of the CMA-170 is 25 lbs
(11.34 kg).
Measurements in: inches
[millimeters]
DIMENSIONS
Installation Instructions CMA170
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
CMA170 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
A (1)
B (1) C (2) D (1)
5/32" E (1)
3/16"
F (2)
10-24 x 1/4" G (2)
1/4-20 x 3/8" H (2)
1/4-20 x 7/8" J (4)
5/16-18 x 7/8" K (4)
5/16-18 x 1-1/8" L (4)
10-24 x 1/4"
M (4) N (4)
(Only used with
optional CMA152)
(Only used with
optional CMA152)
Security
Installation Instructions CMA170
5
Assembling CMA-170
1. Swing open the CMA-170 end door. (See Figure 1)
2. Lift end door up and out of top tab. (See Figure 1)
Figure 1
3. Remove hardware bag from inside CMA-170.
Installing CMA-170
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
NOTE: The projector/display must be removed from the mount
before installing this accessory.
Installing CMA-170 Horizontally to Projector
Mount
1. Attach CMA-170 to projector pipe mount using two pipe
brackets (C), four 5/16-18 x 1-1/8" button head cap screws
(K) and nylon spacers (N). (See Figure 2)
NOTE: If NOT using the optional CMA-152, instead use four
5/16-18 x 7/8" button head cap screws (J) and nylon
spacers (M). (See Figure 2)
Figure 2
Installing CMA-170 Vertically to Projector Mount
1. Attach CMA-170 to projector pipe mount using two pipe
brackets (C), four 5/16-18 x 1-1/8" button head cap screws
(K) and nylon spacers (N). (See Figure 3)
NOTE: If NOT using the optional CMA-152, instead use four
5/16-18 x 7/8" button head cap screws (J) and nylon
spacers (M). (See Figure 3)
Figure 3
1
2
(C) x 2
(N) x 4
[or (M) x 4]
(K) x 4
[or (J) x 4]
Optional
CMA-152
(A)
(K) x 4
[or (J) x 4]
(C) x 2
(N) x 4
[or (M) x 4]
(A)
Optional
CMA-152
CMA170 Installation Instructions
6
Installing CMA-170 to Display
NOTE: A PCS/MCS bracket must be used to attach a display
to the CMA-170.
1. Attach bracket (B) to CMA-170 using two 1/4-20 x 7/8"
button head cap screws (H) from INSIDE CMA-170. (See
Figure 4)
Figure 4
2. Attach CMA-170 to PCS/MCS bracket using two
1/4-20 x 3/8" button head cap screws (G). (See Figure 5)
Figure 5
3. Attach CMA-170 to display pipe mount using one pipe
bracket (C), two 5/16-18 x 7/8" button head cap screws (J)
and nylon spacers (M). (See Figure 6)
Figure 6
Reattaching Projector/Display
1. Reattach the pipe to the ceiling mount following instructions
included with the mount.
2. Reattach the projector/display to the mount following
instructions included with the mount.
Installing CPU
1. Install the CPU into the CMA-170 and place it on the six
shelves located in the CMA-170. (See Figure 7)
Figure 7
1
(H) x 2
(B)
(A)
2
(G) x 2
(A)
PCS/MCS
3
(J) x 2
(M) x 2
(C)
(A)
Place CPU on
interior shelves
CPU
(A)
Installation Instructions CMA170
7
NOTE: In a sample installation, install components into the
CMA-170 in the following order (See Figure 8):
1. CPU;
2. Remote control;
3. Cables should be installed and run through the cable
access holes;
4. Power supply.
Figure 8
Securing CMA-170
1. Add the door to CMA-170 by placing the top tab into the slot
on top of CMA-170. (See Figure 9)
2. Swing the door bottom into place. (See Figure 9)
Figure 9
3. Fasten CMA-170 door closed with two 10-24 x 1/4" button
head cap security screws (F). (See Figure 10)
NOTE: Phillips head screws (L) are provided if security screws
are not required. Security screws can also be removed
from the other CMA-170 door and replaced with the
Phillips head screws (L).
Figure 10
1
2
3
4
Run
Cables
2
1
CPU
(A)
Slot
3
(F) x 2
(A)
CMA170 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
P+86-755-8996 9226 ; 8996 9236 ; 8996 9220
F+86-755-8996 9217
8803-000081
2007 Chief Manufacturing
www.chiefmfg.com
03/07
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief KITQS012C Le manuel du propriétaire
- Catégorie
- Mur
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Chief KITQS012C Owner's manual
Documents connexes
-
Chief Manufacturing RPMA1 Manuel utilisateur
-
Chief LCDPA Guide d'installation
-
-
Chief RPEUW Guide d'installation
-
Chief Manufacturing LCD2C Manuel utilisateur
-
Chief RSMEU spécification
-
Chief FCA4U Guide d'installation
-
Chief FCA3U Guide d'installation
-
-
Chief Manufacturing PL2A Manuel utilisateur