User Manual
Before using self-ballasted LED lamp please read the safety instructions carefully
Can use on a stable source of voltage that fluctuates in wide range AC120V 60Hz
Always turn off the switch when replacing or cleaning the lamp. Remove and install it bygrasping
only the plastic portion of the lamp.
This product can replace incandescent lamp to use in indoor, residential and commercial lighting
Never use in the following conditions
1 Power supply with low voltage DC such as emergency light
2 Where water may drop on the lamp
3 Unsuitable for application when the lamp must turn on and off frequently
4 Do not use in moist spot and airtight lamp fixture
5 This device is not intended for use with emergency exit fixtures or emergency exit lights
This product must not be disposed together with the domestic waste. This product has to be disposed
at an authorized place for recycling of electrical and electronic appliances.
By collecting and recycling waste, you help save natural resources, and make sure the product is
disposed in an environmental friendly and healthy way.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste
separately for special treatment is necessary.
This is WIFI signal contorl dimmable LED Lamp. Please do not use any dimmer.
“For lamps with a weight significantly higher than that of the lamps for which they are a
replacement, attention should be drawn to the fact that the increased weight may reduce
the mechanical stability of certain luminaires and lampholders and may impair contact
making and lamp retention.”
Use in Dry Locations only
The light source contained in this lamp shall only be replaced by the manufacturer or his service
agent or a similar qualified person.
For lamps with a weight significantly higher than that of the lamps for which they are a replacement,
attention should be drawn to the fact that the increased weight may reduce the mechanical stability of
certain luminaires and lampholders and may impair contact making and lamp retention.
Product name: LED LAMP
Model name: 2ANTY-B0002
FCC ID: 2ANTYB0002
IC: 26025-B0002
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
This product complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This modular must be installed and operated with a minimum distance of 20
cm between the radiator and user body.
IC Warning
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
IC Radiation Exposure Statement
This product complies with IC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter. This modular must be installed and operated with a
minimum distance of 20 cm between the radiator and user body.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement
Déclaration de rayonnement IC
Ce complies avec des radiations émettrices de rayonnement Environnement. Ceci ne doit
pas être co-localisé ou opérer avec des autres Ce modular doit être installé et obtenu
avec une distance minimale de 20 cm entre les radiateurs et le corps de l’utilisateur.
-
1
-
2
