Össur COLD RUSH Instructions For Use Manual

Marque: Össur

Modèle: COLD RUSH

Taper: Instructions For Use Manual

Instructions for Use

COLD RUSH™

Cold Therapy System

EN | Instructions for Use 5

FR | Notice d’utilisation 16

ES | Instrucciones para el uso 28



XMA























XMA









MAX





























ENGLISH

SAFETY PRECAUTIONS

WARNING: The Cold Rush cold therapy system can be cold enough to

seriously injure skin. Read the instructions which are located inside the

unit, the instructions for the pad, and the labels on the device carefully

before operating the Cold Rush cold therapy system.

WARNING: RX ONLY.

The device should only be used with a prescription from a physician that

includes the following treatment information: () the duration of the

entire cold therapy protocol, () the length of individual cold therapy

sessions, as well as the length of breaks from cold therapy treatment, ()

setting of flow control knob, () instructions about how to inspect the

skin, and () frequency of skin checks.

WARNING: SKIN INSPECTION AND ADVERSE REACTIONS.

The patient or his healthcare provider must check the skin at least every

- hours during use of this device, regardless of whether the patient is

asleep or awake. The patient must discontinue the use of the Cold Rush

Cold Therapy Unit if he experiences any adverse reaction to the treatment

area such as: increase in pain, burning, blistering, itching, increased

swelling, discoloration of the skin, increased redness, welts or any other

changes in the appearance of the skin.

WARNING: NO DIRECT CONTACT WITH SKIN:

INSULATION BARRIER REQUIRED (not included).

The Cold Rush Pad should never make direct contact with the skin. An

insulation barrier between the pad and the skin should be used at all

times without exception in accordance with instruction from the

physician so as to prevent the skin from becoming too cold. The Cold

Rush pad operating temperature is too cold to be placed directly on the

skin.

• Unit is not suitable for use in the presence of flammable anesthetic

mixture with air, oxygen or nitrous oxide.

• Follow local ordinances or regulations for proper disposal of device,

accessories and packaging.

• Caution: Federal law requires this device to be sold by a physician or

by the order of a physician.

WARNING

Read the following treatment warning protocol instructions carefully

before operating the cold rush cold therapy system.

• The flow control knob should never be set at the maximum settings

(number “4” or “MAX”) for more than  minutes.

MAX

















• The Cold Rush pad should never be applied directly to the patient’s

skin. Do not use the Cold Rush Cold Therapy System without first

applying an insulation barrier between the Cold Rush pad and the

patient’s skin.

• Patients should never utilize cold therapy while they are asleep or

unable to check their skin every - hours unless specifically

instructed to do so by the prescribing health care provider.

• Patients must check their skin every - hours once steady flow of

water through the pad is achieved. Turn the flow control knob

counterclockwise to increase the temperature (warmer), and

clockwise to decrease the temperature (colder).

• When turning the unit on, turn the flow control knob clockwise to the

number “3” setting wait  minutes to allow the temperature to

stabilize before making any additional temperature adjustments.

MAX









• The following patients should ALWAYS turn the flow control knob

counterclockwise to the number “1” setting when using cold therapy

– Patients whose treatment area has been desensitized due to local

anesthesia or regional nerve blockers

– Patients taking prescribed medications that may negatively affect

peripheral vascular circulation, including beta adrenergic blockers

and local epinephrine use (such as in local anesthetics)

– Patients taking prescribed medications that negatively affect their

mental capacity or judgment

– Patients suffering from diabetes

– Patients who have recently undergone hand/wrist or foot/ankle

surgery

– Patients suffering from cognitive disabilities

– Young children and the elderly

• Caution: Contact your healthcare provider immediately and

discontinue the use of your Cold Rush Cold Therapy Unit if you

experience any adverse reaction to the treatment area such as:

increase in pain, burning, blistering, itching, increased swelling,

discoloration of the skin, increased redness, welts or any other

changes in the appearance of the skin.

• Make sure that the insulation barrier is dry.

• Care should be taken during prolonged use for children, diabetics,

incapacitated patients and those with decreased skin sensitivity or

poor circulation.

• A licensed healthcare practitioner must determine the correct

frequency and duration of treatment for each patient.

• If prescribed by a licensed healthcare practitioner for home use, the

healthcare practitioner must provide each patient with training for

appropriate use and proper application of the Cold Rush Cold Therapy

System.

• The health care practitioner must monitor the patient’s use of the

device to assure appropriate use and proper application of cold

therapy, including but not limited to application of an insulation

barrier between the patient’s skin and the Cold Rush Pad.

• The product should never be left unattended when plugged in.

• Never drop or insert any object into any opening or hose.

• Do not operate where aerosol (spray) products are being used or

where oxygen is being administered.

• Do not attempt to drag or reposition the Cold Rush Cold Therapy unit

by pulling or tugging on the insulated hoses, as this may cause

damage to the unit and/or cause the hoses to disconnect. Use handle

when moving the Cold Rush Cold Therapy unit.

• If you experience disturbance in any other electrical equipment near

the Cold Rush unit, please try to unplug it from the wall socket to

verify that it is not the source of disturbance.

ELECTRIC SHOCK HAZARD

• Unplug unit before filling it with ice and water. To avoid danger of

electric shock be certain that hands are dry before inserting or

removing the power supply from wall socket.

• Avoid getting water or ice on the flow control panel or power adapter.

• Always unplug this product immediately after each use.

• Do not use while bathing.

• Do not place or store product where it can fall or be pulled into a tub

or sink.

• Do not place in or drop into water or other liquid.

• Do not reach for a product that has fallen into water. Unplug

immediately.

• Never operate this product if it has a damaged electrical cord or plug,

if it is not working properly, if it has been dropped or damaged, or

dropped into water. Return the product to your healthcare provider for

examination and repair.

• Keep cord away from heated surfaces.

NOTE: To create the safest operating conditions possible, Össur has

designed the Cold Rush Cold Therapy System to operate on a  volt

power supply, significantly reducing the chance of dangerous electric

shock. Great care should always be taken when using electricity near

water.

PRODUCT DEFINITIONS

• The Cold Rush Cold Therapy System is designed for single patient use

only.

• Use of Cold Rush Cold Therapy System is designed to reduce

localized pain and swelling following surgical procedures or trauma.

LIST OF PARTS Figure 

a. Cold Rush Cold Therapy System

b. Hose

c. Couplings

d. Flow Control Knob

e. DC Connector

f. V Power Supply

g. Cold Rush Pad (Sold Separately)

TECHNICAL SPECIFICATION

Do not use any other power supply other than the one provided with the

unit.

ELECTRICAL  POWER SUPPLY

• Model no: UESWU-SPA

• Input: V US, V EU

• Input frequency: Hz US, Hz EU

• Output power: W

• Output Voltage: V

• Output Current: .A

SAFETY STANDARDS

Cold Rush™ Cold Therapy System is tested and certified to comply with

the IEC- standard of electrical safety of medical devices and IEC/

EN--, electromagnetic compatibility for medical electrical devices.

The company fulfills the requirements of ISO.

SETUP AND OPERATION

. Ensure cold therapy unit is turned off, turn flow control knob counter

clockwise to the off position. Do not plug in to wall socket (Figure )

. Fill reservoir with water to the indicated fill line (Figure )

. Add chopped or cubed ice to the reservoir up to the indicated fill line

(Figure )

. Attach the provided V power supply to DC power port, do not plug

into wall circuit (Figure )

. Apply insulation barrier over the patient’s skin in the area to be

treated (Figure a)

. Apply Cold Rush Pad over insulation barrier. The Cold Rush Pad

should never be applied directly over the patient’s skin (Figure b)

. Connect Cold Rush pad to hose extending from the unit. To ensure

proper connection, push couplings together until they snap into place

(Figure )

. Plug the provided v power supply to wall socket (V US, V

Europe) (Figure )

. Turn flow control knob clockwise to the number "" setting, this will

turn unit on (Figure )

. Wait  minutes to allow temperature to stabilize before adjusting the

temperature for comfort (Figure )

– Turn flow control knob counterclockwise to increase temperature.

– Turn flow control knob clockwise to decrease temperature.

. To turn the cold therapy unit off, turn flow control knob

counterclockwise until it stops.

. Always turn the cold therapy unit off before disconnecting the Cold

Rush pad or any hoses. To disconnect the hoses, press the release

tabs on the coupling and pull the connectors apart.

. Drain all of the water out of the cold therapy unit after each use.

. Follow directions - before each use.

MAINTENANCE

Do not try to repair your Cold Rush unit as this may create a user hazard

and will automatically void warranty. After talking with your healthcare

provider, to ensure you are following the operating instructions properly,

the unit shall be sent to Össur for repairs or maintenance. No other

company or individual is allowed to service or repair the unit in any way.

CLEANING AND PROLONGED STORAGE

• When you have finished all of your cold therapy treatments, prior to

prolonged storage, fill the unit with one gallon of water (or enough so

the water level is at the ice fill line.

• Add  tablespoons of liquid bleach or  ounces of % hydrogenated

peroxide to the water and mix.

• Connect hoses to the Cold Rush Pad, turn unit on to MAX setting.

• Allow water mixture to circulate for  minutes.

• Turn unit off and unplug the power supply.

• Carefully drain the water mixture out of the unit and store in a cool

dark place leaving the lid slightly open. (Exposure to sunlight and

extreme heat may damage hoses and unit.)

• When reusing the unit after storage, fill the reservoir with clean water

and turn the pump on to circulate the water through the hoses and

flush the remaining water mixture out of the system (use old pad for

this procedure, discard the pad after cleaning is completed).

• Dispose water and refill the reservoir with fresh ice and water

combination to begin cold therapy treatment. Follow operating

instructions - before each use.

• Before you use the unit, inspect hoses and new pad for any tears or

breaks. Contact your healthcare provider to obtain new Cold Rush

pad.

• Clean or replace insulation barrier as recommended by your

healthcare practitioner.

ENVIRONMENTAL

• Operating Temperature: +°C to °C

• Operating Humidity: % - % Relative Humidity

• Atmosphere Pressure: h Pa –  h Pa

• Shipping and Storage Temperature: -°C to °C

• Shipping and Storage Humidity: % - % Relative Humidity, non-

condensing

Guidance and Manufacturer’s Declaration – Electromagnetic Emissions

The device is intended for use in the electromagnetic environment specified

below. The customer or user of device should assure that it is used in such an

environment.

Emissions Test Compliance

Electromagnetic Environment –

Guidance

RF Emissions CISPR  Group  The device uses RF energy only for

its internal function. Therefore, its

RF emissions are low and are not

likely to cause any interference in

nearby electronic equipment.

RF Emissions CISPR  Class B The device is suitable for use in all

establishments, including domestic

establishments and those directly

connected to the public low voltage

power supply network that supplies

buildings used for domestic

purposes.

Harmonics Emissions

IEC --

Class B

Voltage Fluctuations/

Flicker Emissions

vIEC --

Complies

Guidance and Manufacturer’s Declaration – Electromagnetic Emissions

The device is intended for use in the electromagnetic environment specified below. The customer or user of device should assure that it is used in such an environment.

Immunity Test IEC  Test Level

Compliance Level Electromagnetic Environment – Guidance

Electrostatic Discharge (ESD)

IEC --

± kV contact

± kV air

± kV contact

± kV air

Floors should be wood, concrete, or ceramic

tile. If floors are covered with synthetic

material, the relative humidity should be at

least %.

Electrical fast transient/burst

IEC --

± kV for power supply lines

± kV for input/output lines

± kV for power supply lines

± kV for input/output lines

Mains power quality should be that of a

typical commercial or hospital environment.

Surge IEC -- ± kV line(s) to line(s)

± kV line(s) to earth

± kV line(s) to line(s)

± kV line(s) to earth

Mains power quality should be that of a

typical commercial or hospital environment.

Voltage dips, Short

interruptions and voltage

variations on power supply

lines IEC --

< % UT (> % dip in UT) for . cycle.

 % UT ( % dip in UT) for  cycles.

 % UT ( % dip in UT) for  cycles.

< % UT (>% dip in UT) for  s.

< % UT (> % dip in UT) for . cycle.

 % UT ( % dip in UT) for  cycles.

 % UT ( % dip in UT) for  cycles.

< % UT (>% dip in UT) for  s.

Mains power quality should be that of a

typical commercial or hospital environment.

If the user of the device requires continued

operation during power mains interruptions,

it is recommended that the device be

powered from an uninterruptible power

supply or a battery.

Power frequency (/ Hz)

magnetic field

IEC --

 A/m

 A/m Power frequency magnetic fields should be at

levels characteristic of a typical location in a

typical commercial or hospital environment.

Note: UT is the a.c. mains voltage prior to application of the test level.

Guidance and Manufacturer’s Declaration – Electromagnetic Emissions

The device is intended for use in the electromagnetic environment specified below. The customer or user of device should assure that it is used in such an environment.

Immunity Test IEC  Test Level

Compliance Level Electromagnetic Environment – Guidance

Electrostatic Discharge (ESD)

IEC --

± kV contact

± kV air

± kV contact

± kV air

Floors should be wood, concrete, or ceramic

tile. If floors are covered with synthetic

material, the relative humidity should be at

least %.

Electrical fast transient/burst

IEC --

± kV for power supply lines

± kV for input/output lines

± kV for power supply lines

± kV for input/output lines

Mains power quality should be that of a

typical commercial or hospital environment.

Surge IEC -- ± kV line(s) to line(s)

± kV line(s) to earth

± kV line(s) to line(s)

± kV line(s) to earth

Mains power quality should be that of a

typical commercial or hospital environment.

Voltage dips, Short

interruptions and voltage

variations on power supply

lines IEC --

< % UT (> % dip in UT) for . cycle.

 % UT ( % dip in UT) for  cycles.

 % UT ( % dip in UT) for  cycles.

< % UT (>% dip in UT) for  s.

< % UT (> % dip in UT) for . cycle.

 % UT ( % dip in UT) for  cycles.

 % UT ( % dip in UT) for  cycles.

< % UT (>% dip in UT) for  s.

Mains power quality should be that of a

typical commercial or hospital environment.

If the user of the device requires continued

operation during power mains interruptions,

it is recommended that the device be

powered from an uninterruptible power

supply or a battery.

Power frequency (/ Hz)

magnetic field

IEC --

 A/m

 A/m Power frequency magnetic fields should be at

levels characteristic of a typical location in a

typical commercial or hospital environment.

Note: UT is the a.c. mains voltage prior to application of the test level.

Guidance and Manufacturer’s Declaration – Electromagnetic Emissions

The device is intended for use in the electromagnetic environment specified below. The customer or user of the device should assure that it is used in such an environment.

Immunity Test IEC  Test Level Compliance Level

Electromagnetic Environment – Guidance

Portable and mobile RF communications equipment should be used no closer to any

part of the device, including cables, than the recommended separatvion distance

calculated from the equation applicable to the frequency of the transmitter.

Recommended separation distance:

Conducted RF IEC --  Vrms,  kHz to  MHz  Vrms

d=.√P

Radiated RF IEC --  V/m,  MHz to . GHz  V/m

d=.√P  MHz to  MHz

d=.√P  MHz to . GHz

where “P” is the maximum output power rating of the transmitter in watts (W)

according to the transmitter manufacturer and d is the recommended separation

distance in metres (m).

Field strengths from fixed RF transmitters, as determined by an electromagnetic site

survey*, should be less than the compliance level in each frequency range**.

Interference may occur in the vicinity of

equipment marked with the following symbol:

Note 

At  MHz and  MHz, the higher frequency range applies.

Note 

These guidelines may not apply in situations. Electromagnetic propagation is

affected by absorption and reflection from structures, objects and people.

Field strengths from fixed transmitters, such as base stations for radio (cellular/

cordless) telephones and land mobile radios, amateur radio, AM and FM radio

broadcast and TV broadcast cannot be predicted theoretically with accuracy. To

assess the electromagnetic environment due to fixed RF transmitters, an

electromagnetic site survey should be considered. If the measured field strength in

the location in which the device is used exceeds the applicable RF compliance level

above, the device should be observed to verify normal operation. If abnormal

performance is observed, additional measures may be necessary, such as

re-orienting or relocating the device.

Over the frequency range  kHz to  MHz, field strengths should be less than

 V/m.