Zebra LS3408 Guide de démarrage rapide

Marque: Zebra

Modèle: LS3408

Catégorie: Lecteurs de codes à barres

Taper: Guide de démarrage rapide

LS/DS3408

http://www.zebra.com/ls3408

http://www.zebra.com/ds3408

See Product Reference Guide

for detailed information

POST IN WORK AREA

1 Tether Plate

2 LED Indicators

3 Scan Window

4 Scan Trigger

Variants

Accessories

Laser Scanner

(ER, FZ)

Digital Scanner

(DS)

IntelliStand Forklift Holder

CORD ATTACHMENT

HOST INTERFACES

NOTE: Cables may vary depending on configuration

TROUBLESHOOTING

IBM 46XX

USBRS-232 Keyboard Wedge

Wand Emulation

Scanner Emulation

No power to scanner

Check system power;

ensure power supply,

if required, is connected

Incorrect interface cable used

Ensure that correct

interface cable is used

Interface/power cables are loose

Check for loose cable

connections

Scanner not working

Bar code unreadable

Ensure bar code is not defaced;

try scanning test bar code of sam

bar code type

Distance between scanner

and bar code incorrect

Move scanner closer to

or further from bar code

Scanner not programmed

for bar code type

Ensure scanner is programmed

to read type of bar code being

scanned

Scanner not decoding bar code

Scanner not programmed for correct host interface

Check scanner host parameters or edit options

Interface cable is loose

Check for loose cable connections

Scanner decoding bar code, but data not transmitting to host

Scanner not programmed for correct host interface

Check scanner host parameters or edit options

Scanned data incorrectly displayed on host

Set Defaults

LS/DS3408 PROGRAMMING BAR CODES

RS-232 Host Types Enter Key (Carriage Return/Line Feed)

Wand Emulation Host Types

Keyboard Wedge Host Types

USB Host Types

IBM 46XX Host Types

SET DEFAULTS

HID KEYBOARD EMULATION

IBM HAND-HELD USB

PORT 5B

PORT 9B

STANDARD RS-232

ICL RS-232

NIXDORF RS-232 MODE A

SYMBOL WAND

ENABLE CONVERT TO CODE 39

DISABLE CONVERT TO CODE 39

SCAN OPTIONS

ENTER

NIXDORF RS-232 MODE B

FUJITSU RS-232

OPOS/JPOS

IBM PC/AT and IBM PC COMPATIBLE

Quick Start Guide

Auto Aim trigger mode is the default (red laser aiming pattern automatically turns on when

the digital scanner senses motion). After 2 seconds of inactivity, the red laser aiming pattern

automatically shuts off. To turn off default, scan Level below to activate the red laser aiming

pattern and decode processing upon trigger pull. Decode processing continues until bar code

decodes, trigger release or Decode Session Timeout is reached.

Level (00h)

Level

http://www.zebra.com/ls3408

http://www.zebra.com/ds3408

LS/DS3408

ENGLISH HEBREW

CLASS 1 CLASS 1 LASER PRODUCT

CLASS 2 LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

DANISH / DANSK ITALIAN / ITALIANO

KLASSE 1 KLASSE 1 LASERPRODUKT CLASSE 1 PRODOTTO AL LASER DI CLASSE 1

KLASSE 2 LASERLYF CLASSE 2 LUCE LASER

SE IKKE IND I STRÅLEN NON FISSARE IL RAGGIOPRODOTTO

KLASSE 2 LASERPRODUKT AL LASER DI CLASSE 2

DUTCH / NEDERLANDS NORWEGIAN / NORSK

KLASSE 1 KLASSE-1 LASERPRODUKT KLASSE 1 LASERPRODUKT, KLASSE 1

KLASSE 2 LASERLICHT KLASSE 2 LASERLYS IKKE STIRR INN ILYSSTRÅLEN

NIET IN STRAAL STAREN LASERPRODUKT, KLASSE 2

KLASSE-2 LASERPRODUKT

FINNISH / SUOMI PORTUGUESE / PORTUGUÊS

LUOKKA 1 LUOKKA 1 LASERTUOTE CLASSE 1 PRODUTO LASER DA CLASSE 1

LUOKKA 2 LASERVALO CLASSE 2 LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO

ÄLÄ TUIJOTA SÄDETTÄ PRODUTO LASER DA CLASSE 2

LUOKKA 2 LASERTUOTE

FRENCH / FRANÇAIS SPANISH / ESPAÑOL

CLASSE 1 PRODUIT LASER DE CLASSE 1 CLASE 1 PRODUCTO LASER DE LA CLASE 1

CLASSE 2 LUMIERE LASER CLASE 2 LUZ LASER

NE PAS REGARDER LE RAYON FIXEMENT NO MIRE FIJAMENTE EL HAZ

PRODUIT LASER DE CLASSE 2 PRODUCTO LASER DE LA CLASE 2

GERMAN / DEUTCH SWEDISH / SVENSKA

KLASSE 1 LASERPRODUKT DER KLASSE 1 KLASS 1 LASERPRODUKT KLASS 1

KLASSE 2 LASERSTRAHLEN KLASS 2 LASERLJUS STIRRA INTE MOT STRÅLEN

NICHT DIREKT IN DEN LASERSTRAHL LASERPRODUKT KLASS 2

SCHAUEN

LASERPRODUKT DER KLASSE 2

JAPANESE /

CHINESE / 简体中文

1 类 1 类激光产品

2 类激光切勿注视光束

2 类激光产品

LASER LIGHT- DO NOT STARE INTO BEAM . CLASS 2

LASER PRODUCT. LASERLICHT -

NICHT IN DEN

STRAHL BLICKEN. LASER KLASSE 2. LUMIÈRE

LASER - NE PAS

REGARDER DANS LE FAISCEAU.

APPAREIL À LASER DE CLASSE 2 630-680nm, 1mW

CAUTION - CLASS 3R LASER LIGHT WHEN OPEN. AVOID DIRECT

EYE EXPOSURE LUMIÈRE LASER EN CAS D'OUVERTURE DE

CLASSE 3R. EXPOSITION DANGEREUSE AU FAISCEAU. KLASSE

3R, VORSICHT - LASERLICHT, WENN ABDECKUNG GEÖFFNET.

NICHT DEM STRAHL AUSSETZEN.

COMPLIES WITH 21CFR1040.10 AND 1040.11

EXCEPT FOR DEVIATIONS

PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007 AND

IEC 60825-1 (Ed. 2.0), EN60825-1:2007.

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-103. CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST

CONFORME À LA NORME NMB-003 DU CANADA.

English: For EU Customers: All products at the end of their life must be returned

to Zebra for recycling. For information on how to return product, please go to:

http://www.zebra.com/weee.

Bulgarish: За клиенти от ЕС: След края на полезния им живот всички

продукти трябва да се връщат на Zebra за рециклиране. За информация

относно връщането на продукти, моля отидете на адрес:

http://www.zebra.com/weee.

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich

životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení

produktu najdete na webové stránce: http://www.zebra.com/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når

de er udtjent. Læs oplysningerne om returnering af produkter på:

http://www.zebra.com/ weee.

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer

Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur

Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας

ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για

περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,

επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada

taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote

tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.

Español: Para clientes en la Unión Europea: todos los productos deberán

entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea

más información sobre cómo devolver un producto, visite:

http://www.zebra.com/weee.

Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de

vie doivent être retournés à Zebra pour recyclage. Pour de plus amples

informations sur le retour de produits, consultez : http://www.zebra.com/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del

rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il

riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito

Web: http://www.zebra.com /weee.

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir

jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu

nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi

būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti

gaminį, rasite: http://www.zebra.com/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra

vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának

módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee

weboldalra.

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu

tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif

għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van

hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg

http://www.zebra.com/weee voor meer informatie over het terugzenden van

producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji

nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu

produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser

devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver

o produto, visite: http://www.zebra.com/weee.

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de

funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre

returnarea produsului, accesaţi: http://www.zebra.com/weee.

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí

doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o

vrátení výrobkov nájdete na: http://www.zebra.com/weee.

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe

vrniti podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite:

http://www.zebra.com/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava

kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen

palauttamisesta on osoitteessa http://www.zebra.com/weee.

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste

returneras till Zebra för återvinning. Information om hur du returnerar produkten

finns på http://www.zebra.com/weee.

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme

için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için

lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.

012345

OPTIMUM UPRIGHT BODY POSTURE AVOID EXTREME WRIST ANGLES

Low/medium/high beep

Power up

Short high beep

Bar code decoded

[if decode beeper

enabled]

4 long low beeps

Transmission error

detected; data is

ignored

Standard Use

High/low beep

Correct programming

sequence performed

Low/high beep

Incorrect

programming

sequence or

Cancel bar code

scanned

High/low/high/low beep

Successful

parameter

setting

Parameter Menu Scanning

BEEPER INDICATIONS

LED Indications

Off

Scanner is on

and ready to scan,

or no power to

scanner

Green

Bar code is successfully

decoded

Red

Transmission

error

Local Contact:

POST IN WORK AREAPOST IN WORK AREA

72-67131-02 Revision A June 2004

OPTIMUM SCANNING POSITIONS

TAKING BREAKS AND TASK ROTATION RECOMMENDEDTAKING BREAKS AND TASK ROTATION RECOMMENDED

ALTERNATE LEFT AND RIGHT HANDSALTERNATE LEFT AND RIGHT HANDS

1 Tether Plate

2 LED Indicators

3 Scan Window

4 Scan Trigger

Optimum Body Posture

for Low Scanning

ALTERNATE LEFT

AND RIGHT KNEES

Optimum Body Posture for

Extended Range Scanning

Tested to comply

with FCC Standards

FOR HOME OR OFFICE USE

REGULATORY INFORMATION

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury follow

the recommendations below. Consult with your local Health & Safety Manager to

ensure that you are adhering to your company's safety programs to prevent

employee injury.

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures.

Regulatory Information

This guide applies to the following Model Numbers: DS3408, LS3408. All

Zebra devices are designed to be compliant with rules and regulations in

locations they are sold and will be labeled as required.

Any changes or modifications to Zebra equipment, not expressly approved by

Zebra, could void the user's authority to operate the equipment.

Radio Frequency Interference Requirements

Note: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

However there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Interference Requirements – Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Marking and European Economic Area (EEA)

Statement of Compliance

Zebra Technologies Corporation, hereby declares that this device is in compliance

with all the applicable Directives, 2004/108/EC, 2006/95/EC and 2011/65/EU. A

Declaration of Conformity may be obtained from http://www.zebra.com/doc.

Laser Devices

Zebra products using lasers comply with US 21CFR1040.10

and1040.11 except for deviations pursuant to laser notice no.

50, dated June 24, 2007 and IEC 60825-1 (Ed. 2.0), EN60825-1:2007.

The laser classification is marked on one of the labels on the product.

Class 1 Laser devices are not considered to be hazardous when used for their

intended purpose. The following statement is required to comply with US and

international regulations:

Caution: Use of controls, adjustments or performance of procedures other

than those specified herein may result in hazardous laser light exposure.

Class 2 laser scanners use a low power, visible light diode. As with any very bright

light source, such as the sun, the user should avoid staring directly into the light

beam. Momentary exposure to a Class 2 laser is not known to be harmful.

Scanner Labeling

AVOID EXTREME

WRIST ANGLES

AVOID REACHING

AVOID BENDING

Laser Scanner

(ER, FZ)

Aiming Digital Scanner

(DS)

OPTIMUM BODY POSTURE

Recommended Usage Guide

72-67131-04 Rev A March 2015

Zebra Technologies Corporation

Lincolnshire, IL U.S.A.

http://www.zebra.com

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The

Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra

Technologies company.

Zebra reserves the right to make changes to any product to improve reliability,

function, or design.

Zebra does not assume any product liability arising out of, or in connection with,

the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise

under any patent right or patent, covering or relating to any combination, system,

apparatus, machine, material, method, or process in which Zebra products might

be used. An implied license exists only for equipment, circuits, and subsystems

contained in Zebra products.

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The

Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra

Technologies company. Other product names mentioned in this manual may be

trademarks or registered trademarks of their respective companies and are hereby

acknowledged.

Warranty

For the complete Zebra hardware product warranty statement, go to:

http://www.zebra.com/warranty.

Service Information

If you have a problem using the equipment, contact your facility’s Technical or

Systems Support. If there is a problem with the equipment, they will contact the

Zebra Support at: http://www.zebra.com/support.

For the latest version of this guide go to: http://www.zebra.com/support.

Power Supply

Use ONLY a LISTED, Type no. 50-14000, or PWRS-14000, Direct Plug-In power

supply, marked Class 2 or LPS, or SELV, Rated 5 Vdc, 850 m A Min. (IEC 60950-1).

Use of alternative power supply will invalidate any approvals given

to this device and may be dangerous.

Laser Labels

In accordance with Clause 5, IEC 825 and EN60825, the following

information is provided to the user:

Zebra LS3408 Guide de démarrage rapide

Marque: Zebra

Modèle: LS3408

Catégorie: Lecteurs de codes à barres

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: Zebra LS3408 Quick start guide
Nederlands: Zebra LS3408 Snelstartgids

Documents connexes

Autres documents

Motorola DS3407 Guide de démarrage rapide