Zebra DS9808-R Guide de démarrage rapide

Marque: Zebra

Modèle: DS9808-R

Catégorie: Lecteurs de codes à barres

Taper: Guide de démarrage rapide

DS9808-R

QUICK START GUIDE

2 DS9808-R Quick Start Guide

Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does

not assume any product liability arising out of, or in connection with, the application or use of any product,

circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or

otherwise under any patent right or patent, covering or relating to any combination, system, apparatus,

machine, material, method, or process in which Zebra products might be used. An implied license exists only

for equipment, circuits, and subsystems contained in Zebra products. Zebra and the Zebra head graphic are

registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a

Zebra Technologies company.

This Zebra Product may include Zebra Software, Commercial Third Party Software, and Publicly Available

software. Refer to Product Reference Guide for complete copyright, conditions and disclaimer information.

Warranty

For the complete hardware product warranty statement, go to: http://www.zebra.com/warranty.

For Australia Only

For Australia Only. This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson Road,

#05-02/03, Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under

the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation

for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or

replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Zebra Technologies Corporation Australia's limited warranty above is in addition to any rights and remedies

you may have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies

Corporation at+65 6858 0722. You may also visit our website: http://www.zebra.com for the most updated

warranty terms.

Service Information

If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a

problem with the equipment, they will contact the Global Customer Support Center at:

http://www.zebra.com/support.

For the latest version of this guide go to: http://www.zebra.com/support.

DS9808-R Quick Start Guide 3

Scanner Features

RFID

Scan Window

Trigger A

LED

RFID LED

RFID Module

Trigger B

4 DS9808-R Quick Start Guide

Cord Attachment/Removal

DS9808-R Quick Start Guide 5

Programming Bar Codes

Set Defaults

Carriage Return/Line Feed

USB Host Types

HID Keyboard Emulation

IBM Hand-Held USB

SNAPI with Imaging Interface

SNAPI Without Imaging

6 DS9808-R Quick Start Guide

IBM 46XX Host Types

RS-232 Host Types

Port 5B

Port 9B

Port 17

Standard RS-232

Nixdorf RS-232 Mode A

Nixdorf RS-232 Mode B

DS9808-R Quick Start Guide 7

RS-232 Host Types (continued)

RFID Same Tag Timeout

ICL RS-232

Fujitsu

RS-232

OPOS/JPOS

Disable

2 Seconds

5 Minutes

8 DS9808-R Quick Start Guide

RFID Trigger Modes

RFID Data Transmission Format

Continuous

Single Tag

Continuous Re-report

Continuous Flush

Raw

GS1-128

EPC URI

DS9808-R Quick Start Guide 9

Data Capture

Hands-Free Scanning

Hand-Held Scanning

Triggers

DS9808-LR

DS9808-SR

Trigger A

Trigger B

10 DS9808-R Quick Start Guide

Hands-Free RFID

Hand-Held RFID

DS9808-R Quick Start Guide 11

LED Indications

Beeper Indications

Indication LED

Hand-Held Scanning / RFID

The scanner is on and ready to scan/read, or no power to the

scanner

Off

The scanner successfully decoded a bar code or read an RFID tag Green

Transmission error Red

Hands-Free (Presentation) Scanning

No power to the scanner Off

The scanner is ready to scan Green

A bar code is successfully decoded Off momentarily

Transmission error Red

Indication Beeper Sequence

Standard Use

Power up Low/medium/high beep

A bar code is successfully decoded Short medium beep

Transmission error, data is ignored 4 long low beeps

RFID

An RFID tag was read (if RFID read beeper is enabled) Medium/high (two-tone) beep

Unexpected RFID indication High/medium/low/low beeps

Parameter Menu Scanning

Successful parameter setting High/low/high/low beep

Correct programming sequence performed High/low beep

Incorrect programming sequence, or Cancel bar code scanned Low/high beep

12 DS9808-R Quick Start Guide

Optimum Arm Position Avoid Extreme Wrist Angles

Avoid Bending and Reaching

Alternate left and right hands. Taking breaks and task rotation recommended.

AVOID EXTREME

WRIST ANGLES

AVOID REACHING

AVOID BENDING

DS9808-R Quick Start Guide 13

Troubleshooting

Problem Possible Solution

Scanner not working

No power to scanner Check system power; ensure power supply,

if required, is connected

Incorrect interface cable used Use correct interface cable

Interface/power cables are loose Ensure all cable connections are secure

Scanner does not decode bar code

Scanner not programmed for bar code type Ensure the scanner is programmed to read the

type of bar code being scanned

Bar code is unreadable Ensure the bar code is not defaced; scan a test

bar code of the same bar code type

Distance between scanner and bar code is

incorrect

Move the scanner closer to or further from the

bar code

Scanner decodes bar code but does not transmit data to host

Scanner not programmed for correct host

interface

Scan appropriate host parameter bar codes

Interface cable is loose Ensure all cable connections are secure

Scanned data incorrectly displayed on host

Scanner not programmed for correct host

interface

Scan appropriate host parameter bar codes

14 DS9808-R Quick Start Guide

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below.

Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety

programs to prevent employee injury.

•

Reduce or eliminate repetitive motion

•

Maintain a natural position

•

Reduce or eliminate excessive force

•

Keep objects that are used frequently within easy reach

•

Perform tasks at correct heights

•

Reduce or eliminate vibration

•

Reduce or eliminate direct pressure

•

Provide adjustable workstations

•

Provide adequate clearance

•

Provide a suitable working environment

•

Improve work procedures.

Regulatory Information

The guide applies to the following Model Numbers: DS9808-RUS, DS9808-RWW, and DS9808REU.

Local language translations are available at the following website: www.zebra.com/support

All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be

labeled as required. Any changes or modifications to Zebra equipment, not expressly approved by Zebra could

void the user’s authority to operate the equipment.

Caution

Declared maximum operating temperature: 40

C / 104

This guide is available on local languages, translations are available at the following website:

http://www.zebra.com/support

Wireless Device Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved

for use in the following countries: United States, Canada, Mexico, and Europe. Please refer to the Declaration

of Conformity (DoC) for details of other country markings.

This is available at http://www.zebra.com/doc

Note: Europe includes, Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain,

Sweden, Switzerland and the United Kingdom.

DS9808-R Quick Start Guide 15

Radio Frequency Interference Requirements - FCC

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•

Consult the dealer or an experienced radio/TV technician for help.

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Radio Frequency Interference Requirements - Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Radio Transmitters

This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical

specifications were met.

Warnings for Use of Wireless Devices

Please observe all warning notices with regard to the usage of wireless devices.

Potentially Hazardous Atmospheres

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants

etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).

Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical equipment. Wireless

devices should be switched off wherever you are requested to do so in hospitals, clinics or healthcare facilities.

These requests are designed to prevent possible interference with sensitive medical equipment.

16 DS9808-R Quick Start Guide

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a

handheld wireless device and a pacemaker to avoid potential interference with the pacemaker.

These recommendations are consistent with independent research and recommendations by Wireless

Technology Research. Persons with Pacemakers:

•

Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.

•

Should not carry the device in a breast pocket.

•

Should use the ear furthest from the pacemaker to minimise the potential for interference.

•

If you have any reason to suspect that interference is taking place, turn OFF your device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine if the operation of your

wireless product may interfere with the medical device.

RF Exposure Guidelines

International

The device complies with internationally recognized standards covering human exposure to electromagnetic

fields from radio devices. For information on “International” human exposure to electromagnet fields refer to

the Zebra Declaration of Conformity (DoC) at http://www.zebra.com/doc.

For further information on the safety of RF energy from wireless devices - see

www.zebra.com/corporateresponsibility located under Wireless Communications and Health

Safety Information

Reducing RF Exposure – Use Properly

Only operate the device in accordance with the instructions supplied.

Handheld Devices

To comply with FCC RF exposure requirements, this device must be operated in the hand with a minimum

separation distance of 23cm or more from a person’s body. Other operating configurations should be avoided.

Europe Handheld Devices

To satisfy EU RF exposure requirements, a mobile transmitting device must operate with a minimum

separation distance of 8.3cm or more from a person’s body.

DS9808-R Quick Start Guide 17

Marking and European Economic Area (EEA)

RFID devices for use through the EEA have the following restrictions:

•

Maximum radiated transmit power of 2W ERP in the frequency range 865.6-867.6MHz

Statement of Compliance for Wireless Devices Integrated into Terminals

Zebra hereby declares that this device is in compliance with all applicable Directives, 2014/30/EU, 2014/35/EU

and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address:

http://www.zebra.com/doc.

Laser Devices

Complies with 21CFR1040.10 & 1040.11 except for deviations pursuant to Laser Notice NO. 50, dated June

24, 2007 and IEC/EN 60825-1:2007 and/or IEC/EN 60825-1:2014.

The laser classification is marked on one of the labels on the device.

Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the

sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not

known to be harmful.

Power Supply

Use only a approved power supply output rated at 12 VDC / 3.3 A (center positive connector).

The power supply shall be Listed to UL/CSA 60950-1; and certified to IEC60950-1 and EN60950-1 with SELV

outputs.

Use of alternative power supply will invalidate any approval given to this device and may be dangerous.

LASER LIGHT- DO NOT STARE INTO BEAM .

CLASS 2 LASER PRODUCT.

LASERLICHT - NICHT IN DEN

STRAHL BLICKEN. LASER KLASSE 2.

LUMIÈRE LASER - NE PAS REGARDER DANS LE FAISCEAU.

APPAREIL À LASER DE CLASSE 2 630-680nm, 1mW

Caution

class 2 laser light

when open.

Do not stare into beam.

Attention : lumière

laser en cas d'ouverture.

Ne pas regarder dans

le faisceau.

Vorsicht

laserlicht klasse 2,

wenn abdeckung geöffnet.

Nicht in den strahl blicken.

18 DS9808-R Quick Start Guide

Waste Electrical and Electronic Equipment (WEEE)

Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщ ат на Zebra за рециклиране. За

информация относно връщането на продукти, моля отидете на адрес http://www.zebra.com/weee.

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skončení jejich životnosti vrátit společnosti Zebra k recyklaci. Informace o

způsobu vrácení produktu najdete na webové stránce: http://www.zebra.com/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af

produkter på: http://www.zebra.com/weee.

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurückgesandt

werden. Informationen zur Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρ έφονται στην Zebra για

ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση

http://www.zebra.com/weee στο Διαδίκτυο.

English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return

product, please go to: http://www.zebra.com/weee.

Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean

reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.zebra.com/weee.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks

toote tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä.

Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.zebra.com/weee.

Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de

plus amples informations sur le retour de produits, consultez : http://www.zebra.com/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék

visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di

consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web:

http://www.zebra.com/weee.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau

informacijos, kaip grąžinti gaminį, rasite: http://www.zebra.com/weee.

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju

par produktu nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ.

Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor

recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naleźy zwrócić do firmy Zebra w celu ich utylizacji.

Informacje na temat zwrotu produktów znajdują się na stronie internetowej http://www.zebra.com/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações

sobre como devolver o produto, visite: http://www.zebra.com/weee.

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru reciclare.

Pentru informaţii despre returnarea produsului, accesaţi: http://www.zebra.com/weee.

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu.

Bližšie informácie o vrátení výrobkov nájdete na: http://www.zebra.com/weee.

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o vračilu

izdelka obiščite:http://www.zebra.com/weee.

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du

returnerar produkten finns på http://www.zebra.com/weee.

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği

hakkında bilgi için lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.

TURKISH WEEE Statement of Compliance

EEE Yönetmeligine Uygundur

DS9808-R Quick Start Guide 19

72E-125703-03EN Revision A - October 2016

Zebra Technologies Corporation

3 Overlook Point

Lincolnshire, IL U.S.A.

http://www.zebra.com

Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions

worldwide. All other trademarks are the property of their respective owners.

Zebra DS9808-R Guide de démarrage rapide

Marque: Zebra

Modèle: DS9808-R

Catégorie: Lecteurs de codes à barres

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: Zebra DS9808-R Quick start guide
Nederlands: Zebra DS9808-R Snelstartgids
polski: Zebra DS9808-R Skrócona instrukcja obsługi

Zebra DS9808-R Guide de démarrage rapide

Zebra DS9808-R Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents