Zebra DS6708 Guide de démarrage rapide

Marque: Zebra

Modèle: DS6708

Catégorie: Lecteurs de codes à barres

Taper: Guide de démarrage rapide

http://www.zebra.com/ds6708

DS6708

RS-232

USB

IBM 46XX

DS6708 Poster

BLACK

PANTONE 285

Perforation

DS6708 Poster

POST IN WORK AREAPOST IN WORK AREA

Quick Start Guide

ACCESSORIES

CORD ATTACHMENT/REMOVAL

See Product Reference Guide

for detailed information

HOST INTERFACES

NOTE: Cables may vary depending on configuration

TROUBLESHOOTING

No power to scanner

Check system power;

ensure power supply,

if required, is connected

Incorrect interface cable used

Ensure that correct

interface cable is used

Ensure all cable connections

are secure

Scan appropriate host parameter bar codes Ensure all cable connections are secure

Interface/power cables are loose

Scanner not working

Bar code unreadable

Ensure bar code is not defaced;

try scanning test bar code of same

bar code type

Distance between scanner

and bar code incorrect

Move scanner closer to

or further from bar code

Scanner not programmed

for bar code type

Ensure scanner is programmed

to read type of bar code being

scanned

Scanner not decoding bar code

Scanner not programmed for correct host interface Interface cable is loose

Scanner decoding bar code, but data not transmitting to host

Scanner not programmed for correct host interface

Scan appropriate host parameter bar codes

Scanned data incorrectly displayed on host

DS6708 PROGRAMMING BAR CODES

1 LED Indicators

2 Scan Window

3 Scan Trigger

IntelliStand

Desk Cup

Wall Mount

SET DEFAULTS

HID KEYBOARD EMULATION

IBM HAND-HELD USB

ICL RS-232

NIXDORF RS-232 MODE A

NIXDORF RS-232 MODE B

FUJITSU RS-232

OPOS/JPOS

Keyboard Wedge

IBM PC/AT and IBM PC COMPATIBLE

PORT 5B

PORT 9B

STANDARD RS-232

LEVEL

Enter Key (Carriage Return/Line Feed)

RS-232 Host Types

Set Defaults

IBM 46XX Host Types

USB Host Types

Keyboard Wedge Host Types

Level

http://www.zebra.com/ds6708

DS6708

English: For EU Customers: All products at the end of their life must be returned

to Zebra for recycling. For information on how to return product, please go to:

http://www.zebra.com/weee.

Bulgarish: За клиенти от ЕС: След края на полезния им живот всички

продукти трябва да се връщат на Zebra за рециклиране. За информация

относно връщането на продукти, моля отидете на адрес:

http://www.zebra.com/weee

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich

životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení

produktu najdete na webové stránce: http://www.zebra.com/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når

de er udtjent. Læs oplysningerne om returnering af produkter på:

http://www.zebra.com/weee.

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer

Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur

Rücksendung von Produkten finden Sie unter

http://www.zebra.com/weee.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής

τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες

πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη

διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada

taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote

tagastamise kohta külastage palun aadressi:

http://www.zebra.com/weee.

Español: Para clientes en la Unión Europea: todos los productos deberán

entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea

más información sobre cómo devolver un producto, visite:

http://www.zebra.com/weee.

Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie

doivent être retournés à Zebra pour recyclage. Pour de plus amples informations

sur le retour de produits, consultez : http://www.zebra.com/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo

ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per

informazioni sulle modalità di restituzione, visitare il seguente sito Web:

http://www.zebra.com/weee.

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā

atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu

nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti

grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį,

rasite: http://www.zebra.com/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz

kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával

kapcsolatos tudnivalókért látogasson el a

http://www.zebra.com/weee weboldalra.

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu

tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif

għandek tirritorna l-prodott, jekk jogħġbok żur:

http://www.zebra.com/weee

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun

levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg

http://www.zebra.com/weee voor meer informatie over het terugzenden van

producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji

nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu

produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser

devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver

o produto, visite: http://www.zebra.com/weee.

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de

funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre

returnarea produsului, accesaţi: http://www.zebra.com/weee.

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí

doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o

vrátení výrobkov nájdete na: http://www.zebra.com/weee.

Slovenski:

Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti

podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite:

http://www.zebra.com/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava

kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen

palauttamisesta on osoitteessa http://www.zebra.com/weee.

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste

returneras till Zebra för återvinning. Information om hur du returnerar produkten

finns på http://www.zebra.com/weee.

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme

için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için

lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.

012345

LASER LIGHT- DO NOT STARE INTO

BEAM . CLASS 2 LASER PRODUCT.

LASERSTRAHLUNG - NICHT IN DEN

STRAHL BLICKEN. LASER KLASSE 2.

LUMI»RE LASER - NE PAS REGARDER

DANS LE FAISCEAU. APPAREIL ¿ LASER

DE CLASSE 2 630-680nm, 1mW

OPTIMUM ARM POSITION AVOID EXTREME WRIST ANGLES

Low/medium/high beep

Power up

Short medium beep

Bar code decoded

4 long low beeps

Transmission error

detected; data is

ignored

Standard Use

High/low beep

Correct programming

sequence performed

Low/high beep

Incorrect

programming

sequence or

“Cancel” bar code

scanned

High/low/high/low beep

Successful

parameter

setting

Parameter Menu Scanning

BEEPER INDICATIONS LED INDICATIONS

Off

Scanner is on

and ready to scan,

or no power to

scanner

Green

Bar code is successfully

decoded

Red

Transmission

error

Local Contact:

OPTIMUM SCANNING

1 LED Indicators

2 Scan Window

3 Scan Trigger

AVOID BENDING AND REACHING

Tested to comply

with FCC Standards

FOR HOME OR OFFICE USE

REGULATORY INFORMATION

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the

recommendations below. Consult with your local Health & Safety Manager to ensure that you

are adhering to your company's safety programs to prevent employee injury.

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures.

Regulatory Information

This guide applies to Model Number DS6708.

All Zebra devices are designed to be compliant with rules and regulations in locations they

are sold and will be labeled as required.

Local language translations are available at the following website:

http://www.zebra.com/support.

Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could

void the user’s authority to operate the equipment.

Antennas: Use only the supplied or an approved replacement antenna. Unauthorized

antennas, modifications, or attachments could cause damage and

may violate regulations.

Radio Frequency Interference Requirements

Note: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide

reasonable protection against harmful interference

in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. However there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Interference Requirements – Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Marking and European Economic Area (EEA)

Statement of Compliance

Zebra hereby declares that this device is in compliance with all the applicable Directives,

2004/108/EC, 2006/95/EC and 2011/65/EU. A Declaration of Conformity may be obtained from

ttp://www.zebra.com/doc.

Ukraine

Laser Devices

Zebra products using lasers comply with US 21CFR1040.10

and1040.11 except for deviations pursuant to laser notice no.

50, dated June 24, 2007 and IEC 60825-1 (Ed. 2.0),

EN60825-1:2007.

The laser classification is marked on one of the labels on the product.

Class 1 Laser devices are not considered to be hazardous when used for their

intended purpose. The following statement is required to comply with US and

international regulations:

Caution: Use of controls, adjustments or performance of procedures other

than those specified herein may result in hazardous laser light exposure.

Class 2 laser scanners use a low power, visible light diode. As with any very bright

light source, such as the sun, the user should avoid staring directly into the light

beam. Momentary exposure to a Class 2 laser is not known to be harmful.

Scanner Labeling

AVOID REACHING

AVOID BENDING

Recommended Usage Guide

AVOID EXTREME

WRIST ANGLES

72-83973-02 Revision A March 2015

Alternate left and right hands

taking breaks and task rotation

recommended

Alternate left and right hands

taking breaks and task rotation

recommended

Aiming

123SCAN

123Scan

is an easy-to-use, PC-based software tool that enables rapid and easy customized setup via a bar code or USB

cable. For more information, visit: http://www.zebra.com/123Scan2.

123SCAN

Zebra reserves the right to make changes to any product to improve reliability, function, or

design. Zebra does not assume any product liability arising out of, or in connection with, the

application or use of any product, circuit, or application described herein. No license is granted,

either expressly or by implication, estoppel, or otherwise under any patent right or patent,

covering or relating to any combination, system, apparatus, machine, material, method, or

process in which Zebra products might be used. An implied license exists only for equipment,

circuits, and subsystems contained in Zebra products.

Warranty

For the complete Zebra hardware product warranty statement, go to:

http://www.zebra.com/warranty.

For Australia Only

For Australia Only. This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71

Robinson Road, #05-02/03, Singapore 068895, Singapore. Our goods come with guarantees

that cannot be excluded under the Australia Consumer Law. You are entitled to a

replacement or refund for a major failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if

the goods fail to be of acceptable quality and the failure does not amount to a major

failure.

Zebra Technologies Corporation Australia’s limited warranty above is in addition to any

rights and remedies you may have under the Australian Consumer Law. If you have any

queries, please call Zebra Technologies Corporation at+65 6858 0722. You may also visit

our website: http://www.zebra.com for the most updated warranty terms.

Service Information

If you have a problem using the equipment, contact your facility’s Technical or Systems Support.

If there is a problem with the equipment, they will contact the Zebra Support Center at:

http://www.zebra.com/support.

For the latest version of this guide go to: http://www.zebra.com/support.

Power Supply

Use ONLY a LISTED, Type no. 50-14000, or PWRS-14000, Direct Plug-In power supply, marked

Class 2 or LPS, or SELV, Rated 5 Vdc, 850 m A Min.

(IEC 60950-1). Use of alternative power supply will invalidate any approvals given

to this device and may be dangerous.

Zebra Technologies Corporation

Lincolnshire, IL U.S.A.

http://www.zebra.com

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a

registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.

Zebra DS6708 Guide de démarrage rapide

Marque: Zebra

Modèle: DS6708

Catégorie: Lecteurs de codes à barres

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: Zebra DS6708 Quick start guide
Nederlands: Zebra DS6708 Snelstartgids

Zebra DS6708 Guide de démarrage rapide

Zebra DS6708 Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents